AD9911BCPZ-REEL7

500 MSPS Direct Digital Synthesizer with 10-Bit DAC AD9911 Data Sheet FEATURES GENERAL DESCRIPTION Patented SpurKiller technology Multitone generation Test-tone modulation Up to 800 Mbps data throughput Matched latencies for frequency/phase/amplitude changes Linear frequency/phase/amplitude sweeping capability Up to 16 levels of FSK, PSK, ASK Programmable DAC full-scale current 32-bit frequency tuning resolution 14-bit phase offset resolution 10-bit output amplitude-scaling resolution Software-/hardware-controlled power-down Multiple device synchronization Selectable 4× to 20× REF_CLK multiplier (PLL) Selectable REF_CLK crystal oscillator 56-lead LFCSP The AD9911 is a complete direct digital synthesizer (DDS). This device includes a high speed DAC with excellent wideband and narrowband spurious-free dynamic range (SFDR) as well as three auxiliary DDS cores without assigned digital-to-analog converters (DACs). These auxiliary channels are used for spur reduction, multitone generation, or test-tone modulation. The AD9911 is the first DDS to incorporate SpurKiller technology and multitone generation capability. Multitone mode enables the generation up to four concurrent carriers; frequency, phase and amplitude can be independently programmed. Multitone generation can be used for system tests, such as inter-modulation distortion and receiver blocker sensitivity. SpurKilling enables customers to improve SFDR performance by reducing the magnitude of harmonic components and/or the aliases of those harmonic components. Test-tone modulation efficiently enables sine wave modulation of amplitude on the output signal using one of the auxiliary DDS cores. APPLICATIONS Agile local oscillator Test and measurement equipment Commercial and amateur radio exciter Radar and sonar Test-tone generation Fast frequency hopping Clock generation The AD9911 can perform modulation of frequency, phase, or amplitude (FSK, PSK, ASK). Modulation is implemented by storing profiles in the register bank and applying data to the profile pins. In addition, the AD9911 supports linear sweep of frequency, phase, or amplitude for applications such as radar and instrumentation. (continued on Page 3) 500MSPS DDS CORE MODULATION CONTROL REF CLOCK INPUT CIRCUITRY RECONSTRUCTED SINE WAVE SPUR REDUCTION/ MULTITONE TIMING AND CONTROL USER INTERFACE 05785-002 SYSTEM CLOCK SOURCE 10-BIT DAC Figure 1. Basic Block Diagram Rev. A Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2006–2016 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD9911 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Linear Sweep No Dwell Mode .................................................. 25 Applications ....................................................................................... 1 Sweep and Phase Accumulator Clearing Functions .............. 26 General Description ......................................................................... 1 Output Amplitude Control ....................................................... 26 Revision History ............................................................................... 2 Synchronizing Multiple AD9911 Devices ................................... 28 Functional Block Diagram .............................................................. 3 Operation .................................................................................... 28 Specifications..................................................................................... 4 Automatic Mode Synchronization ........................................... 28 Absolute Maximum Ratings ............................................................ 9 Manual Software Mode Synchronization ................................ 28 ESD Caution .................................................................................. 9 Manual Hardware Mode Synchronization .............................. 28 Equivalent Input and Output Circuits ....................................... 9 I/O_Update, SYNC_CLK, and System Clock Relationships 29 Pin Configuration and Function Descriptions ........................... 10 I/O Port ............................................................................................ 30 Typical Performance Characteristics ........................................... 12 Overview ..................................................................................... 30 Application Circuits ....................................................................... 17 Instruction Byte Description .................................................... 30 Theory of Operation ...................................................................... 18 I/O Port Pin Description ........................................................... 31 Primary DDS Core ..................................................................... 18 I/O Port Function Description ................................................. 31 SpurKiller/Multitone Mode and Test-Tone Modulation ....... 18 MSB/LSB Transfer Description ................................................ 31 D/A Converter ............................................................................ 18 I/O Modes of Operation ............................................................ 31 Modes of Operation ....................................................................... 19 Register Maps .................................................................................. 35 Single-Tone Mode ...................................................................... 19 Control Register Map ................................................................ 35 SpurKiller/Multitone Mode ...................................................... 19 Channel Register Map ............................................................... 36 Test-tone Mode ........................................................................... 20 Profile Register Map................................................................... 37 Reference Clock Modes ............................................................. 20 Control Register Descriptions ...................................................... 38 Scalable DAC Reference Current Control Mode ................... 21 Channel Select Register (CSR) ................................................. 38 Power-Down Functions ............................................................. 21 Channel Function Register (CFR) Description...................... 39 Shift Keying Modulation ........................................................... 21 Outline Dimensions ....................................................................... 41 Shift Keying Modulation Using SDIO Pins for RU/RD ........ 23 Ordering Guide .......................................................................... 41 Linear Sweep (Shaped) Modulation Mode ............................. 23 REVISION HISTORY 11/2016—Rev. 0 to Rev. A Changes to Figure 43 Caption....................................................... 25 Updated Outline Dimensions ....................................................... 41 5/2006—Revision 0: Initial Version Rev. A | Page 2 of 41 Data Sheet AD9911 GENERAL DESCRIPTION The DDS acts as a high resolution frequency divider with the REF_CLK as the input and the DAC providing the output. The REF_CLK input can be driven directly or used in combination with an integrated REF_CLK multiplier (PLL). The REF_CLK input also features an oscillator circuit to support an external crystal as the REF_CLK source. The crystal can be used in combination with the REF_CLK multiplier. Flexibility is provided by four data pins (Pin SDIO_0, Pin SDIO_1, Pin SDIO_2, and Pin SDIO_3) that allow four programmable modes of I/O operation. The AD9911 I/O port offers multiple configurations to provide significant flexibility. The I/O port offers an SPI-compatible mode of operation that is virtually identical to the SPI operation found in earlier Analog Devices DDS products. The DDS core (the AVDD pins and the DVDD pins) is powered by a 1.8 V supply. The digital I/O interface (SPI) operates at 3.3 V and requires that the Pin DVDD_I/O (Pin 49) be connected to 3.3 V. The DAC output is supply referenced and must be terminated into AVDD by a resistor and an AVDD center-tapped transformer. The DAC has its own programmable reference to enable different full-scale currents. FUNCTIONAL BLOCK DIAGRAM Σ 32 FTW/ ∆FTW 32 32 Σ Σ PHASE/ ∆PHASE 15 COS(X) 10 10 AMP/ ∆AMP 14 MUX AD9911 Σ DAC SCALABLE DAC REF CURRENT 10 IOUT IOUT DAC_RSET SPURKILLER/ MULTI-TONE MUX DDS CORE SYNC_CLK TIMING AND CONTROL LOGIC BUFFER/ XTAL OSCILLATOR CLK_MODE_SEL REF CLOCK MULTIPLIER 4× TO 20× PWR_DWN_CTL MASTER_RESET SYSTEM CLK ÷4 REF_CLK REF_CLK DDS CORE CONTROL REGISTERS CHANNEL REGISTERS MUX I/O PORT BUFFER PROFILE REGISTERS LOOP FILTER 1.8V 1.8V AVDD DVDD 3.3V P0 P1 Figure 2. Functional Block Diagram Rev. A | Page 3 of 41 P2 P3 DVDD_I/O SCLK CS SDIO_0 SDIO_1 SDIO_2 SDIO_3 05785-001 SYNC_IN SYNC_OUT I/O_UPDATE DDS CORE AD9911 Data Sheet SPECIFICATIONS AVDD and DVDD = 1.8 V ± 5%; DVDD_I/O = 3.3 V ± 5%; RSET = 1.91 kΩ; external reference clock frequency = 500 MSPS (REF_CLK multiplier bypassed), unless otherwise noted. Table 1. Parameter REF CLOCK INPUT CHARACTERISTICS Frequency Range REF_CLK Multiplier Bypassed REF_CLK Multiplier Enabled Internal VCO Output Frequency Range VCO Gain Bit Set 1 Internal VCO Output Frequency Range VCO Gain Bit Cleared Crystal REF_CLK Source Range Input Power Sensitivity Input Voltage Bias Level Input Capacitance Input Impedance Duty Cycle with REF_CLK Multiplier Bypassed Duty Cycle with REF_CLK Multiplier Enabled CLK Mode Select (Pin 24) Logic 1 V CLK Mode Select (Pin 24) Logic 0 V DAC OUTPUT CHARACTERISTICS Full-Scale Output Current Gain Error Output Current Offset Differential Nonlinearity Integral Nonlinearity Output Capacitance Voltage Compliance Range Min Typ Max Unit 1 10 255 500 125 500 MHz MHz MHz 100 160 MHz 20 −5 30 +3 MHz dBm 55 65 1.8 0.5 V pF Ω % % V V +10 mA %FS 1.15 2 1500 45 35 1.25 10 −10 1 ±0.5 ±1.0 3 AVDD – 0.50 25 AVDD + 0.50 Measured at the pin (single-ended) 1.8 V digital input logic 1.8 V digital input logic Must be referenced to AVDD 10 mA is set by RSET = 1.91 kΩ µA LSB LSB pF V WIDEBAND SFDR The frequency range for wideband SFDR is defined as dc to Nyquist 1 MHz to 20 MHz Analog Output 20 MHz to 60 MHz Analog Output 60 MHz to 100 MHz Analog Output −65 −62 −59 dBc dBc dBc 100 MHz to 150 MHz Analog Output 150 t MHz to 200 MHz Analog Output −56 −53 dBc dBc WIDEBAND SFDR Improvement Spur Reduction Enabled 60 MHz to 100 MHz Analog Output 100 MHz to 150 MHz Analog Output 150 MHz to 200 MHz Analog Output Test Conditions/Comments Programs devices on an individual basis to enable spur reduction. See the SpurKiller/Multitone Mode section. 8 15 12 Rev. A | Page 4 of 41 dBc dBc dBc Data Sheet Parameter NARROWBAND SFDR 1.1 MHz Analog Output (±10 kHz) AD9911 Min Typ Max Unit −90 dBc 1.1 MHz Analog Output (±50 kHz) 1.1 MHz Analog Output (±250 kHz) −88 −86 dBc dBc 1.1 MHz Analog Output (±1 MHz) 15.1 MHz Analog Output (±10 kHz) −85 −90 dBc dBc 15.1 MHz Analog Output (±50 kHz) 15.1 MHz Analog Output (±250 kHz) −87 −85 dBc dBc 15.1 MHz Analog Output (±1 MHz) 40.1 MHz Analog Output (±10 kHz) 40.1 MHz Analog Output (±50 kHz) −83 −90 −87 dBc dBc dBc 40.1 MHz Analog Output (±250 kHz) 40.1 MHz Analog Output (±1 MHz) −84 −82 dBc dBc 75.1 MHz Analog Output (±10 kHz) 75.1 MHz Analog Output (±50 kHz) −87 −85 dBc dBc 75.1 MHz Analog Output (±250 kHz) 75.1 MHz Analog Output (±1 MHz) 100.3 MHz Analog Output (±10 kHz) −83 −82 −87 dBc dBc dBc 100.3 MHz Analog Output (±50 kHz) 100.3 MHz Analog Output (±250 kHz) −85 −83 dBc dBc 100.3 MHz Analog Output (±1 MHz) 200.3 MHz Analog Output (±10 kHz) −81 −87 dBc dBc 200.3 MHz Analog Output (±50 kHz) 200.3 MHz Analog Output (±250 kHz) −85 −83 dBc dBc 200.3 MHz Analog Output (±1 MHz) −81 dBc –150 –159 –165 –165 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –142 –151 –160 –162 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –135 –146 –154 –157 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –134 –144 –152 –154 dBc/Hz dBc/Hz dBc/Hz dBc/Hz PHASE NOISE CHARACTERISTICS Residual Phase Noise @ 15.1 MHz (fOUT) 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 40.1 MHz (fOUT) 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 75.1 MHz (fOUT) 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 100.3 MHz (fOUT) 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Rev. A | Page 5 of 41 Test Conditions/Comments AD9911 Parameter Residual Phase Noise @ 15.1 MHz (fOUT) with REF_CLK Multiplier Enabled 5× 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 40.1 MHz (fOUT) with REF_CLK Multiplier Enabled 5× 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 75.1 MHz (fOUT) with REF_CLK Multiplier Enabled 5× 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 100.3 MHz(fOUT) with REF_CLK Multiplier Enabled 5× 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 15.1 MHz (fOUT) with REF_CLK Multiplier Enabled 20× 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 40.1 MHz (fOUT) with REF_CLK Multiplier Enabled 20× 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 75.1 MHz (fOUT) with REF_CLK Multiplier Enabled 20× 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Residual Phase Noise @ 100.3 MHz (fOUT) with REF_CLK Multiplier Enabled 20× 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 MHz Offset Data Sheet Min Typ Max Unit –139 –149 –153 –148 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –130 –140 –145 –139 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –123 –134 –138 –132 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –120 –130 –135 –129 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –127 –136 –139 –138 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –117 –128 –132 –130 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –110 –121 –125 –123 dBc/Hz dBc/Hz dBc/Hz dBc/Hz –107 –119 –121 –119 dBc/Hz dBc/Hz dBc/Hz dBc/Hz Rev. A | Page 6 of 41 Test Conditions/Comments Data Sheet Parameter I/O PORT TIMING CHARACTERISTICS Maximum Frequency Clock (SCLK) Minimum SCLK Pulse Width Low (tPWL) Minimum SCLK Pulse Width High (tPWH) Minimum Data Set-Up Time (tDS) Minimum Data Hold Time Minimum CSB Set-Up Time (tPRE) Minimum Data Valid Time for Read Operation MISCELLANEOUS TIMING CHARACTERISTICS Master_Reset Minimum Pulse Width I/O_Update Minimum Pulse Width Minimum Set-Up Time (I/O_Update to SYNC_CLK) Minimum Hold Time (I/O_Update to SYNC_CLK) Minimum Set-Up Time (Profile Inputs to SYNC_CLK) Minimum Hold Time (Profile Inputs to SYNC_CLK) Minimum Set-Up Time (SDIO Inputs to SYNC_CLK) Minimum Hold Time (SDIO Inputs to SYNC_CLK) Propagation Delay Between REF_CLK and SYNC_CLK CMOS LOGIC INPUT VIH VIL Logic 1 Current Logic 0 Current Input Capacitance CMOS LOGIC OUTPUTS (1 mA Load) VOH VOL POWER SUPPLY Total Power Dissipation—Single-Tone Mode Total Power Dissipation—With Sweep Accumulator Total Power Dissipation—3 Spur Reduction/Multitone Channels Active Total Power Dissipation—Test-Tone Modulation Total Power Dissipation—Full Power Down IAVDD—Single-Tone Mode IAVDD— Sweep Accumulator, REF_CLK Multiplier, and 10-Bit Output Scalar Enabled IDVDD—Single-Tone Mode IDVDD—Sweep Accumulator, REF_CLK Multiplier, and 10-Bit Output Scalar Enabled IDVDD_I/O IDVDD_I/O IAVDD Power-Down Mode IDVDD Power-Down Mode AD9911 Min Typ Max Unit 200 MHz ns ns ns ns ns ns 1.6 2.2 2.2 0 1.0 12 Test Conditions/Comments 1 1 4.8 ns Minimum pulse width = 1 sync clock period Minimum pulse width = 1 sync clock period Rising edge to rising edge 0 ns Rising edge to rising edge 5.4 ns 0 ns 2.5 ns 0 ns 2.25 3.5 5.5 2.0 3 −12 2 0.8 12 2.7 0.4 ns V V µA µA pF V V 241 241 mW mW Dominated by supply variation Dominated by supply variation 351 mW Dominated by supply variation 264 mW Dominated by supply variation 1.8 73 73 mW mA mA 50 50 mA mA 40 30 0.7 1.1 mA mA mA mA Rev. A | Page 7 of 41 IDVDD = read IDVDD = write AD9911 Parameter DATA LATENCY (PIPELINE DELAY) SINGLETONE MODE 2, 3 Frequency, Phase, and Amplitude Words to DAC Output with Matched Latency Enabled Frequency Word to DAC Output with Matched Latency Disabled Phase Offset Word to DAC Output with Matched Latency Disabled Amplitude Word to DAC Output with Matched Latency Disabled DATA LATENCY (PIPELINE DELAY) MODULATION MODE 4 Frequency Word to DAC Output Data Sheet Min Max 29 25 17 34 29 Amplitude Word to DAC Output 21 Unit Test Conditions/Comments SYSCLK cycles SYSCLK cycles SYSCLK cycles SYSCLK cycles 29 Phase Offset Word to DAC Output DATA LATENCY (PIPELINE DELAY) LINEAR SWEEP MODE4 Frequency Rising/Falling Delta Tuning Word to DAC Output Phase Offset Rising/Falling Delta Tuning Word to DAC Output Amplitude Rising/Falling Delta Tuning Word to DAC Output Typ SYSCLK Cycles SYSCLK Cycles SYSCLK Cycles 41 SYSCLK Cycles SYSCLK Cycles SYSCLK Cycles 37 29 For the VCO frequency range of 160 MHz to 255 MHz, the appropriate setting for the VCO gain bit is dependent upon supply, temperature and process. Therefore, in a production environment this frequency band must be avoided. Data latency is reference to the I/O_UPDATE pin. 3 Data latency is fixed and the units are system clock (SYSCLK) cycles 4 Data latency is referenced to a profile change. 1 2 Rev. A | Page 8 of 41 Data Sheet AD9911 ABSOLUTE MAXIMUM RATINGS Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Table 2. Parameter Maximum Junction Temperature DVDD_I/O (Pin 49) AVDD, DVDD Digital Input Voltage (DVDD_I/O = 3.3 V) Digital Output Current Storage Temperature Operating Temperature Lead Temperature (10 sec Soldering) θJA θJC Rating 150°C 4V 2V −0.7 V to +4 V 5 mA –65°C to +150°C –40°C to +85°C 300°C 21°C/W 2°C/W ESD CAUTION EQUIVALENT INPUT AND OUTPUT CIRCUITS REF_CLK INPUTS AVDD 1.5kΩ DAC OUTPUTS Z Z 1.5kΩ REF_CLK REF_CLK AVDD CMOS DIGITAL INPUTS DVDD_I/O = 3.3V IOUT AVDD IOUT AMP Figure 3. CMOS Digital Inputs Figure 4. DAC Outputs Rev. A | Page 9 of 41 NOTES 1. REF_CLK INPUTS ARE INTERNALLY BIASED AND NEED TO BE AC-COUPLED. 2. OSC INPUTS ARE DC-COUPLED. Figure 5. REF_CLK Inputs 05785-005 NOTES 1. AVOID OVERDRIVING DIGITAL INPUTS. NOTES 1. TERMINATE OUTPUTS INTO AVDD. 2. DO NOT EXCEED OUTPUTS VOLTAGE COMPLIANCE. 05785-004 OUTPUT 05785-003 INPUT OSC AD9911 Data Sheet 56 55 54 53 52 51 50 49 48 47 46 45 44 43 DGND DVDD SYNC_CLK SDIO_3 SDIO_2 SDIO_1 SDIO_0 DVDD_I/O SCLK CS I/O_UPDATE DVDD DGND P3 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PIN 1 INDICATOR AD9911 TOP VIEW (Not to Scale) 42 41 40 39 38 37 36 35 34 33 32 31 30 29 P2 P1 P0 AVDD AGND AVDD IOUT IOUT AGND AVDD NC AVDD AVDD AVDD AVDD NC DAC_RSET AGND AVDD AGND AVDD REF_CLK REF_CLK CLK_MODE_SEL AGND AVDD LOOP_FILTER NC 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SYNC_IN SYNC_OUT MASTER_RESET PWR_DWN_CTL AVDD NC AVDD AVDD AVDD NC AVDD NC AVDD AVDD NOTES 1. THE EXPOSED EPAD ON BOTTOM SIDE OF PACKAGE IS AN ELECTRICAL CONNECTION AND MUST BE SOLDERED TO GROUND. 2. PIN 49 IS DVDD_I/O AND IS TIED TO 3.3V. 05785-006 NC = NO CONNECT Figure 6. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 Mnemonic SYNC_IN I/O I 2 SYNC_OUT O 3 MASTER_RESET I 4 5, 7, 8, 9, 11, 13, 14, 15, 19, 21, 26, 29, 30, 31, 33, 37, 39 18, 20, 25, 34, 38 45, 55 44, 56 35 36 17 PWR_DWN_CTL AVDD I I AGND DVDD DGND IOUT IOUT DAC_RSET I I I O O I 22 REF_CLK I 23 REF_CLK I 24 CLK_MODE_SEL I 27 LOOP_FILTER I Description Synchronizes Multiple AD9911 Devices. Connects to the SYNC_OUT pin of the master AD9911 device. Synchronizes Multiple AD9911 Devices. Connects to the SYNC_IN pin of the slave AD9911 device. Active High Reset Pin. Asserting this pin forces the internal registers to the default state shown in the Register Map section. External Power-Down Control. See the Power Down Functions section for details. Analog Power Supply Pins (1.8 V). Analog Ground Pins. Digital Power Supply Pins (1.8 V). Digital Power Ground Pins. Complementary DAC Output. Terminates into AVDD. True DAC Output. Terminates into AVDD. Establishes the Reference Current for the DAC. A 1.91 kΩ resistor (nominal) is connected from Pin 17 to AGND. Complementary Reference Clock/Oscillator Input. When the REF_CLK is operated in single-ended mode, this pin should be decoupled to AVDD or AGND with a 0.1 µF capacitor. Reference Clock/Oscillator Input. When the REF_CLK operates in single-ended mode, Pin 23 is the input. See the Modes of Operation section for the reference clock configuration. Control Pin for the Oscillator. CAUTION: Do not drive this pin beyond 1.8 V. When high (1.8 V), the oscillator is enabled to accept a crystal as the REF_CLK source. When low, the oscillator is bypassed. Connects to the External Zero Compensation Network of the PLL Loop Filter. Typically, the network consists of a 0 Ω resistor in series with a 680 pF capacitor tied to AVDD. Rev. A | Page 10 of 41 Data Sheet AD9911 Pin No. 6, 10, 12, 16, 28, 32 40, 41, 42, 43 Mnemonic NC P0, P1, P2, P3 I/O N/A I 46 I/O_UPDATE I 47 48 CS SCLK I I 49 50 51, 52, 53 DVDD_I/O SDIO_0 SDIO_1, SDIO_2, SDIO_3 SYNC_CLK I I/O I/O 54 O Description No Connection. Analog Devices recommends leaving these pins floating. These data pins are used for modulation (FSK, PSK, ASK), start/stop for the sweep accumulator, and ramping up/down the output amplitude. Any toggle of these data inputs is equivalent to an I/O_UPDATE. The data is synchronous to the SYNC_CLK (Pin 54). The data inputs must meet the set-up and hold time requirements to the SYNC_CLK. This guarantees a fixed pipeline delay of data to the DAC output; otherwise, a ±1 SYNC_CLK period of uncertainty occurs. The functionality of these pins is controlled by profile pin configuration (PPC) bits in Register FR1 . A rising edge triggers data transfer from the I/O port buffer to active registers. I/O_UPDATE is synchronous to the SYNC_CLK (Pin 54). I/O_UPDATE must meet the set-up and hold time requirements to the SYNC_CLK to guarantee a fixed pipeline delay of data to DAC output. If not, a ±1 SYNC_CLK period of uncertainty occurs. The minimum pulse width is one SYNC_CLK period. The active low chip select allows multiple devices to share a common I/O bus (SPI). Data Clock for I/O Operations. Data bits are written on the rising edge of SCLK and read on the falling edge of SCLK. 3.3 V Digital Power Supply for SPI Port and Digital I/O. Data pin SDIO_0 is dedicated to the I/O port only. Data pins SDIO_1:3 can be used for the I/O port or to initiate a ramp up/ramp down (RU/RD) of the DAC output amplitude. The SYNC_CLK, which runs at ¼ the system clock rate, can be disabled. I/O_UPDATE and profile changes (Pin 40 to Pin 43) are synchronous to the SYNC_CLK. To guarantee a fixed pipeline delay of data to DAC output, I/O_UPDATE and profile changes (Pin 40 to Pin 43) must meet the set-up and hold time requirements to the rising edge of SYNC_CLK. If not, a ±1 SYNC_CLK period of uncertainty exists. Rev. A | Page 11 of 41 AD9911 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS DELTA 1 (T1) –71.73dB 4.50901804MHz REF LVL 0dBm RBW VBW SWT 20kHz 20kHz 1.6s RF ATT 20dB UNIT dB REF LVL 0dBm 0 0 A 1 –10 –40 –40 (dB) –50 dB A 1 1AP –50 –60 –70 1 –80 1 –80 –90 START 0Hz 25MHz/DIV STOP 250MHz –100 START 0Hz Figure 7. fOUT = 1.1 MHz, fCLK = 500 MSPS, Wideband SFDR DELTA 1 (T1) –62.84dB 40.08016032MHz REF LVL 0dBm RBW VBW SWT 20kHz 20kHz 1.6s RF ATT UNIT 05785-010 05785-007 –90 –100 STOP 250MHz 25MHz/DIV Figure 10. fOUT = 15.1 MHz, fCLK = 500 MSPS, Wideband SFDR REF Lv] 0dBm 20dB dB 0 DELTA 1 (T1) –60.13dB 75.15030060MHz 20kHz 20kHz 1.6s RBW VBW SWT RF ATT 20dB UNIT dB A 1 A 1 –10 –10 –20 –20 1AP 1AP –30 –30 –40 –40 (dB) –50 –50 –60 –60 1 1 –70 –70 –80 –80 –90 05785-008 –90 –100 START 0Hz 25MHz/DIV STOP 250Hz –100 START 0Hz DELTA 1 (T1) –59.04dB 100.70140281MHz RBW VBW SWT 20kHz 20kHz 1.6s RF ATT 20dB UNIT dB 25MHz/DIV REF LVL 0dBm 0 DELTA 1 (T1) RBW –53.84dB VBW –101.20240481MHz SWT 20kHz 20kHz 1.6s RF ATT 20dB UNIT dB 0 A 1 –10 A 1 –10 –20 STOP 250MHz Figure 11. fOUT = 75.1 MHz, fCLK = 500 MSPS, Wideband SFDR Figure 8. fOUT = 40.1 MHz, fCLK = 500 MSPS, Wideband SFDR REF LVL 0dBm 05785-011 (dB) 20dB UNIT –20 1AP –30 1AP –30 –40 (dB) –40 –50 –60 –50 –60 1 –70 1 –70 –80 –80 –100 START 0Hz 25MHz/DIV STOP 250MHz 05785-009 –90 Figure 9. fOUT = 100.3 MHz, fCLK = 500 MSPS, Wideband SFDR –90 –100 START 0Hz 25MHz/DIV STOP 250MHz Figure 12. fOUT = 200.3 MHz, fCLK = 500 MSPS, Wideband SFDR Rev. A | Page 12 of 41 05785-012 (dB) –30 –60 (dB) RF ATT –20 1AP –30 0 20kHz 20kHz 1.6s RBW VBW SWT –10 –20 –70 DELTA 1 (T1) –69.47dB 30.06012024MHz Data Sheet REF LVL 0dBm AD9911 DELTA 1 (T1) –84.73dB 254.50901604kHz 0 RBW VBW SWT 500Hz 500Hz 20s RF ATT 20dB UNIT dB REF LVL 0dBm 1 500Hz 500Hz 20s 20dB UNIT dB A 1 –20 1AP –30 –40 –40 (dB) –30 –50 1AP –50 –60 –60 –70 –70 –80 –80 1 1 –90 CENTER 1.1MHz SPAN 1MHz 100kHz/DIV –100 CENTER 15.1MHz Figure 13. fOUT = 1.1 MHz, fCLK = 500 MSPS, NBSFDR, ±1 MHz REF LVL 0dBm DELTA 1 (T1) –84.10dB 120.24048096kHz 0 RBW VBW SWT 500Hz 500Hz 20s RF ATT 20dB UNIT dB 100kHz/DIV SPAN 1MHz Figure 16. fOUT = 15.1 MHz, fCLK = 500 MSPS, NBSFDR, ±1 MHz REF LVL 0dBm DELTA 1 (T1) –86.03dB 262.56513026kHz RBW VBW SWT 500Hz 500Hz 20s RF ATT 20dB UNIT dB 0 A 1 05785-016 05785-013 –90 –100 A 1 –10 –10 –20 –20 1AP –30 –40 –40 (dB) –30 –50 1AP –50 –60 –60 –70 –70 –80 –80 1 1 05785-014 –90 –100 CENTER 40.1MHz 100kHz/DIV SPAN 1MHz –100 CENTER 75.1MHz DELTA 1 (T1) –82.63dB 400.80160321kHz RBW VBW SWT 500Hz 500Hz 20s RF ATT REF LVL 0dBm 20dB UNIT dB 0 DELTA 1 (T1) –83.72dB –400.80160321kHz SPAN 1MHz RBW VBW SWT 500Hz 500Hz 20s RF ATT 20dB UNIT dB 0 A 1 100kHz/DIV Figure 17. fOUT = 75.1 MHz, fCLK = 500 MSPS, NBSFDR, ±1 MHz Figure 14. fOUT = 40.1 MHz, fCLK = 500 MSPS, NBSFDR, ±1 MHz REF LVL 0dBm 05785-017 –90 A 1 –10 –10 –20 –20 1AP –40 –40 (dB) –30 –30 –50 1AP –50 –60 –60 –70 –70 –80 1 –90 –90 –100 CENTER 100.3MHz 100kHz/DIV SPAN 1MHz 1 –100 CENTER 200.3MHz 100kHz/DIV SPAN 1MHz Figure 18. fOUT = 200.3MHz, fCLK = 500 MSPS, NBSFDR, ±1 MHz Figure 15. fOUT = 100.3 MHz, fCLK = 500 MSPS, NBSFDR, ±1 MHz Rev. A | Page 13 of 41 05785-018 –80 05785-015 (dB) RF ATT –10 –20 (dB) RBW VBW SWT 0 A –10 (dB) DELTA 1 (T1) –84.86dB –200.40080160kHz AD9911 Data Sheet –100 235 215 75.1MHz 195 –120 –130 100.3MHz –140 155 135 40.1MHz 115 –160 95 15.1MHz 10 100 1k 10k 100k 1M 10M 75 100 05785-019 –170 FREQUENCY OFFSET (Hz) 150 200 250 300 350 400 450 500 CLOCK FREQUENCY (MHz) Figure 19. Residual Phase Noise (SSB) with fOUT = 15.1 MHz, 40.1 MHz, 75.1 MHz, 100.3 MHz, fCLK = 500 MHz with REF_CLK Multiplier Bypassed 05785-022 –150 175 POWER (mW) PHASE NOISE (dBc/Hz) –110 Figure 22. Power vs. System Clock Frequency –70 0 –80 –20 –100 100.3MHz –30 –110 75.1MHz –120 –40 (dB) –130 –50 –60 40.1MHz –70 15.1MHz –80 –160 –90 100 1k 10k 100k 1M 10M FREQUENCY OFFSET (Hz) 05785-020 –170 10 –100 –70 0 –80 SPAN 15MHz 1 –10 –90 –20 –100 100.3MHz –110 –30 75.1MHz –40 –120 (dB) PHASE NOISE (dBc/Hz) 1.5MHz/ Figure 23. Amplitude Modulation Using Primary Channel (CH1 = 50 MHz) and One Auxiliary Channel (CH0 = 1 MHz) Figure 20. Residual Phase Noise (SSB) with fOUT = 15.1 MHz, 40.1 MHz, 75.1 MHz, 100.3 MHz, fCLK = 500 MHz with REF_CLK Multiplier = 5× –130 40.1MHz –140 –50 –60 15.1MHz –70 –150 –80 –160 –90 100 1k 10k 100k 1M 10M FREQUENCY OFFSET (Hz) Figure 21. Residual Phase Noise(SSB) with fOUT = 15.1 MHz, 40.1 MHz, 75.1 MHz, 100.3 MHz, fCLK = 500 MHz with REF_CLK Multiplier = 20× 05785-021 –170 10 CENTER 50.17407705MHz 05785-057 –150 –100 CENTER 10.2MHz 75kHz/ SPAN 750kHz 05785-058 PHASE NOISE (dBc/Hz) –90 –140 1 –10 Figure 24. Two-Tone Generation Using Primary Channel (CH1 = 10.1 MHz) and One Auxiliary Channel (CH0 = 10.3 MHz) Rev. A | Page 14 of 41 Data Sheet AD9911 –45 0 1 –10 –20 fOUT = 197.7MHz –50 SFDR (dBc) –30 –50 2 –60 3 fOUT = 143.7MHz –55 1 –70 –60 –80 –100 START 0Hz STOP 250MHz 25MHz/ 05785-059 fOUT = 98.7MHz –90 –65 1.5 1.6 1.7 1.8 1.9 2.0 2.1 POWER SUPPLY VOLTAGE (V) Figure 25. SpurKiller Disabled and Three Spurs Identified 05785-028 (dB) –40 Figure 28. SFDR vs. Supply Voltage (AVDD) –40 0 1 –10 –45 –20 SFDR (dBc) –30 (dB) –40 –50 –60 –50 fOUT = 197.7MHz fOUT = 143.7MHz –55 1 –70 –60 –80 25MHz/ STOP 250MHz –65 0 0.375 0.500 0.625 0.750 0.875 1.000 Figure 29. SFDR vs. DAC Output Current –50 0 –10 –52 –20 –54 SFDR (dBc) –30 –40 (dB) 0.250 DAC OUTPUT CURRENT LEVEL (% of Fullscale) Figure 26. SpurKiller Enabled with Three Spurs Reduced (see Figure 25) –50 –60 –70 fOUT = 197.7MHz –56 fOUT = 143.7MHz –58 –60 fOUT = 98.7MHz –62 –80 CENTER 20MHz 4MHz/ SPAN 40MHz 05785-061 –64 –90 –100 0.125 05785-029 START 0Hz –66 –40 -20 0 20 40 60 TEMPERATURE (°C) Figure 27. Three Auxiliary Channels Perform Two-Level FSK with Profile Pins. The three carriers are set to 10 MHz, 20 MHz, and 30 MHz using all three auxiliary channels. Rev. A | Page 15 of 41 Figure 30. SFDR vs. Temperature 80 05785-030 –100 05785-060 fOUT = 98.7MHz –90 AD9911 Data Sheet CH1 100mVΩ M50.0ns CH1 –4mV 05785-056 1 Figure 31. Primary Channel (62 MHz) 100% Amplitude Modulated by CH0 (4 MHz) Rev. A | Page 16 of 41 Data Sheet AD9911 APPLICATION CIRCUITS AD9510, AD9511, ADF4106 ÷ CHARGE PUMP PHASE COMPARATOR LOOP FILTER VCO ÷ REF CLK AD9911 05785-031 REFERENCE LPF Figure 32. DDS in PLL Feedback Locking to Reference Offering Fine Frequency and Delay Adjust Tuning AD9510 CLOCK DISTRIBUTOR WITH DELAY EQUALIZATION CLOCK SOURCE REF_CLK AD9510 SYNCHRONIZATION DELAY EQUALIZATION FPGA SYNC_OUT C1 S1 DATA A1 AD9911 (MASTER) SYNC_CLK C2 S2 DATA (SLAVE 1) SYNC_CLK FPGA C3 S3 DATA FPGA A3 AD9911 (SLAVE 2) SYNC_CLK C4 S4 DATA A4 AD9911 (SLAVE 3) SYNC_CLK A_END 05785-032 CENTRAL CONTROL A2 AD9911 FPGA Figure 33. Synchronizing Multiple Devices to Increase Channel Capacity Using the AD9510 as a Clock Distributor for the Reference and SYNC Clock PROGRAMMABLE 1 TO 32 DIVIDER AND DELAY ADJUST CLOCK OUTPUT SELECTION(S) REF CLK CH 2 LPF AD9515 AD9514 AD9513 AD9512 n LVPECL LVDS CMOS 05785-033 AD9911 n = DEPENDANT ON PRODUCT SELECTION. Figure 34. Clock Generation Circuit Using the AD951x Series of Clock Distribution Chips Rev. A | Page 17 of 41 AD9911 Data Sheet THEORY OF OPERATION PRIMARY DDS CORE The AD9911 has one complete DDS (Channel 1) that consists of a 32-bit phase accumulator, a phase-to-amplitude converter, and 10-bit DAC. Together, these digital blocks generate a sine wave when the phase accumulator is clocked and the phase increment value (frequency tuning word) is greater than 0. The phase-to-amplitude converter translates phase information to amplitude information by a cos (θ) operation. The output frequency (fO) of the DDS is a function of the rollover rate of the phase accumulator. The exact relationship is shown in the following equation: (FTW )( f S ) with 0 ≤ FTW ≤ 231 232 Spur reduction is not as effective at lower fundamental frequencies where SFDR performance is already very good. The benefits of SpurKiller channels are virtually nonexistent when the output frequency is less than 20% of the sampling frequency. Test-tone modulation is similar to amplitude modulation options of a signal generator. For test-tone modulation, auxiliary DDS Channel 0 is assigned to implement amplitude sinusoidal modulated waveforms of the primary channel. This function is programmed using internal registers. D/A CONVERTER where: fS = the system clock rate. FTW = the frequency tuning word. 232 represents the capacity of the phase accumulator’. The DDS core architecture also supports the capability to phase offset the output signal. This is performed by the channel phase offset word (CPOW). The CPOW is a 14-bit register that stores a phase offset value. This value is added to the output of the phase accumulator to offset the current phase of the output signal. The exact value of phase offset is given by the following equation: CPOW  Φ =   × 360°  214  SPURKILLER/MULTITONE MODE AND TEST-TONE MODULATION The AD9911 is equipped with three auxiliary DDS cores (Channel 0, Channel 2, and Channel 3). Because these channels do not have a DAC, there is no direct output. Instead, these channels are designed to implement either spur reduction/ multiple tones or test-tone modulation on the output spectrum for Channel 1. When using multitone mode, the device can output up to four distinct carriers concurrently. This is possible via the summing node for all four DDS cores. The frequency, phase and amplitude of each tone is adjustable. The maximum amplitude of the auxiliary channels is −12 db below the primary channel’s maximum amplitude to prevent overdriving the DAC input. The primary channel’s amplitude can be adjusted down to achieve equal amplitude for all carriers. The AD9911 incorporates a 10-bit current output DAC. The DAC converts a digital code (amplitude) into a discrete analog quantity. The DAC current outputs can be modeled as a current source with high output impedance (typically 100 kΩ). Unlike many DACs, these current outputs require termination into AVDD via a resistor or a center-tapped transformer for expected current flow. The DAC has complementary outputs that provide a combined full-scale output current (IOUT + IOUTB). The outputs always sink current. The full-scale current is controlled by means of an external resistor (RSET) and the scalable DAC current control bits discussed in the Modes of Operation section. The Resistor RSET is connected between the DAC_RSET pin and analog ground (AGND). The full-scale current is inversely proportional to the resistor value as follows: I OUT = 18.91 RSET Limiting the output to 10 mA with an RSET of 1.9 kΩ provides optimal spurious-free dynamic range (SFDR) performance. The DAC output voltage compliance range is AVDD + 0.5 V to AVDD − 0.5 V. Voltages developed beyond this range can cause excessive harmonic distortion. Proper attention should be paid to the load termination to keep the output voltage within its compliance range. Exceeding this range could damage the DAC output circuitry. When using SpurKiller mode, up to three spurs in the output spectrum for Channel 1 are reducible (one per auxiliary channel). To match an exact frequency using the three channels, Rev. A | Page 18 of 41 IOUT 1:1 LPF DAC AVDD IOUT 50Ω 05785-034 fO = the spur must be harmonically related to the fundamental frequency or the tuning word for Channel 1. A nonharmonic spur may be impossible to match frequency. Figure 35. Typical DAC Output Termination Configuration Data Sheet AD9911 MODES OF OPERATION SINGLE-TONE MODE To configure the AD9911 in single-tone mode, the auxiliary DDS cores (CH0, CH2, and CH3) must be disabled by using the channel enable bits and digital powering down (CSR bit ) the three auxiliary DDS cores. Only CH1 remains enabled. See the Register Maps section for a description of the channel enable bits in the channel select register or CSR (Register 0x00). The channel enable bits are enabled or disabled immediately after the CSR data byte is written. An I/O_UPDATE is not required for channel enable bits. The two main registers used in this mode, Register 0x04 and Register 0x05, contain the frequency tuning word and the phase offset word for CH1. The following is a basic protocol to program a frequency tuning word and/or phase offset word for CH1. 1. 2. 3. 4. Power up the AD9911 and issue a master reset. A master reset places the part in single-bit mode for serial programming operations (refer to the I/O Modes of Operation section). The frequency tuning word and phase offset word for CH1 defaults to 0. Disable CH0, CH2, CH3 and enable CH1 using the channel enable bits in Register 0x00. Using the I/O port, program the desired frequency tuning word (Register 0x04) and/or the phase offset word (Register 0x05) for CH1. Send an I/O update signal. CH1 should output its programmed frequency and/or phase offset value, after a pipeline delay (see Table 1). Single-Tone Mode—Matched Pipeline Delay For multitone mode, the digital content of the three auxiliary DDS channels are summed with the primary channel. Each tone can be individually programmed for frequency, phase and amplitude as well as individually modulated using the profile pins in shift-keying modulation. See Figure 24 and Figure 27 for examples. Note the data align bits in Register 0x03 Bits , provide a coarse amplitude adjust setting for the auxiliary channels. These bits default to clear; for multitone mode these bit should typically be set. For SpurKiller mode, the digital contents of the three auxiliary DDS channels are attenuated and summed with the primary channel. In this manner, harmonic spurs from the DAC can be reduced. This is accomplished by matching the frequency of the harmonic component, the amplitude, and the phase (180° offset) of the desired spur on one of the SpurKiller channels. Bench level observations and manipulation are required to establish the optimal parameter settings for the SpurKiller channel(s). The parameters are dependent on the fundamental frequency and system clock frequency. The repeatability of these settings on a unit-to-unit basis depends directly on the SFDR variation of the DAC. The DAC on the AD9911 has enough part-to-part SFDR variation that using a set of fixed programming values across multiple devices will not consistently improve SFDR. Spur reduction performance on an individual device is stable over supply and temperature. The SpurKiller/multitone mode configuration is illustrated in Figure 36. In single-tone mode, the AD9911 offers matched pipeline delay to the DAC input for all frequency, phase, and amplitude changes. The result is that frequency, phase, and amplitude changes arrive at the DAC input simultaneously. The feature is enabled by asserting the match pipeline delay bit found in the channel function register (CSR) (Register 0x03). This feature is available in single-tone mode only. The amplitude of the auxiliary channels uses coarse and fine adjustments to match the amplitude of the targeted spur. The coarse adjust is implemented via the data align bits in Register 0x03 Bits . The approximate amplitude of the auxiliary channel is programmable between −60 dB and −12 dB compared to the full-scale fundamental, per the following equation: SPURKILLER/MULTITONE MODE where AMP is the amplitude and D is the decimal value (0-7) of the data align bits For both SpurKiller and multitone mode, the frequency, phase and amplitude settings of the auxiliary channels and the primary channel use Register 0x04 Bits for frequency and Register 0x05 Bits for phase. Note the channel enable bits in the CSR register must be use to distinguish the content of each channel. See the I/O Port section for details. AMP = −60 dB + (D × 6 dB) For fine amplitude adjustments, the 10-bit output scalar (multiplier) of the auxiliary channel in Register 0x06 Bit is used. The multiplier is enabled by Register 0x06 Bit . A single active SpurKiller channel targeting the second harmonic is expressed as fOUT = A × cos(ωt + Φ1) + B × cos(2ωt + Φ2) + B × cos(2ωt + Φ2 + 180°) + (all other spurious components) where B × cos(2ωt + Φ2 + 180°) represents the fundamental tone of the SpurKiller channel. Rev. A | Page 19 of 41 AD9911 Data Sheet 10 10 COS(X) 10 DAC 1 DDS CORE 1 10-BIT DAC MUX 10 COS(X) DDS CORE 0 10 0 DATA ALIGN 3 CFR 10 COS(X) DDS CORE 2 10 DATA ALIGN 3 CFR DDS CORE 3 DATA ALIGN 10 3 CFR 05785-035 10 COS(X) Figure 36. SpurKiller/Multitone Mode Configuration TEST-TONE MODE Test-tone mode enables sinusoidal amplitude modulation of the carrier (CH1). Setting Bit 2 in Register 0x01 enables test-tone mode. Auxiliary CH2 and CH3 should both be disabled using the channel enable bits (CSR Bit ). The frequency of modulation is set using the frequency tuning word (Register 0x04 Bits ) of auxiliary CH0. Auxiliary CH0 output scalar (Register 0x06 Bits ) sets the magnitude of the modulating signal. See Figure 37 for a diagram of the testtone mode configuration. DDS CORE 1 COS(X) 10 10 DAC 1 10 DDS CORE 0 COS(X) PHASE OFFSET 10 05785-036 14 AMPLITUDE Figure 37. Test-Tone Mode Configuration REFERENCE CLOCK MODES The AD9911 supports several methods for generating the internal system clock. An on-chip oscillator circuit is available for initiating the low frequency reference signal by connecting a crystal to the clock input pins. The system clock can also be generated using the internal, PLL-based reference clock multiplier, allowing the part to operate with a low frequency clock source while still providing a high sample rate for the DDS and DAC. For best phase noise performance, a clean, stable clock with a high slew rate is required. Enabling the PLL allows multiplication of the reference clock frequency from 4× to 20×, in integer steps. The PLL multiplication value is 5-bits located in the Function Register 1 (FR1) Bits . For further information, refer to the Register Map section. When FR1 is programmed with values ranging from 4 to 20 (decimal), the clock multiplier is enabled. The integer value in the register represents the multiplication factor. The system clock rate with the clock multiplier enabled is equal to the reference clock rate times the multiplication factor. If FR1 is programmed with a value less than 4 or greater than 20, the clock multiplier is disabled. Note that the output frequency of the PLL has a restricted frequency range. There is a VCO gain bit that must be set appropriately. The VCO gain bit (FR1) defines two ranges (low/high) of frequency output. See the Register Map section for configuration directions and defaults. The charge pump current in the PLL defaults to 75 μA, which typically produces the best phase noise characteristics. Increasing charge pump current typically degrades phase noise, but decreases the lock time and alters the loop bandwidth. The charge pump control bits (FR1 ) function is described in the Register Map section. To enable the on-chip oscillator for crystal operation, drive CLK_MODE_SEL (Pin 24) high. The CLKMODESEL pin is considered an analog input, operating on 1.8 V logic. With the on-chip oscillator enabled, connection of an external crystal to the REF_CLK and REF_CLKB inputs is made producing a low frequency reference clock. The crystal frequency must be in the range of 20 MHz to 30 MHz. summarizes the clock mode options. See the Register Maps section for more details. Rev. A | Page 20 of 41 Data Sheet AD9911 Table 4. CLK_MODE_SEL Pin 24 High = 1.8 V Logic High = 1.8 V Logic Low Low FR1 PLL, Bits = M 4 ≤ M ≤ 20 M < 4 or M > 20 4 ≤ M ≤ 20 M < 4 or M > 20 The reference clock input circuitry has two modes of operation. The first mode (logic low) configures the circuitry as an input buffer. In this mode, the reference clock must be ac-coupled to the input due to internal dc biasing. This mode supports either differential or single-ended configurations. If single-ended mode is desired, the complementary reference clock input (Pin 23) should be decoupled to AVDD or AGND via a 0.1 µF capacitor. The following three figures exemplify common reference clock configurations for the AD9911. 25Ω 0.1µF 25Ω REF_CLK PIN 23 REF_CLK PIN 22 05785-037 0.1µF REFERENCE CLOCK SOURCE Figure 38. Typical Reference Clock Configuration for Sine Wave Source The reference clock inputs can also support an LVPECL or PECL driver as the reference clock source. 0.1µF LVPECL/ PECL DRIVER REF_CLK PIN 23 REF_CLK PIN 22 05785-038 0.1µF Figure 39. Typical Reference Clock Configuration for LVPECL/PECL Source For external crystal operation, both clock inputs must be dccoupled via the crystal leads and bypassed. Figure 40 shows the configuration when a crystal is used. 25MHz XTAL REF_CLK PIN 23 05785-039 REF_CLK PIN 22 39pF CFR 1 0 1 0 1 1 0 0 LSB Current State Full-scale Half-scale Quarter-scale Eighth-scale POWER-DOWN FUNCTIONS The AD9911 supports pin-controlled power-down plus numerous software selectable power-down modes. Software controlled power-down allows the input clock circuitry, DAC, and the digital logic (for the primary and auxiliary DDS cores) to be individually powered. When the PWR_DWN_CTL input pin is high, the AD9911 enters power-down mode based on the FR1 bit. When the PWR_DWN_CTL input pin is low, the individual power-down bits (CFR ) control the power-down modes of operation. See the Control Register Descriptions section for further details. SHIFT KEYING MODULATION TERMINATION 39pF Min/Max Frequency Range (MHz) 100 < fSYSCLK < 500 20 < fSYSCLK < 30 100 < fSYSCLK < 500 0 < fSYSCLK < 500 Table 5. Reference Clock Input Circuitry 1:1 BALUN System Clock (fSYS CLK) fSYSCLK = fOSC × M fSYSCLK = fOSC fSYSCLK = fREF CLK × M fSYSCLK = fREF CLK Oscillator Enabled Yes Yes No No Figure 40. Crystal Configuration for Reference Clock Source SCALABLE DAC REFERENCE CURRENT CONTROL MODE Set the full-scale output current using bits CFR , as shown in Table 5. The AD9911 can perform 2-/4-/8- or 16-level modulation of frequency, phase, or amplitude (FSK, PSK, ASK) by applying data to the profile pins. SYNC_CLK must be enabled when performing FSK, PSK, or ASK, while the auxiliary DDS cores must be disabled. Digital power down (CSR Bit ) of the auxiliary channels is recommended. In addition, the AD9911 has the ability to ramp up or ramp down the output amplitude before, during, or after a modulation (FSK, PSK only) sequence. This is accomplished by using the 10-bit output scalar. Profile pins or SDIO_1:3 pins can be configured to initiate the ramp up/ramp down (RU/RD) operation. See the Output Amplitude Control section for further details. In modulation mode, a set of control bits (CFR) determines the type (frequency, phase, or amplitude) of modulation. The primary channel (CH1) has 16 profile registers. Register Address 0x0A through Register Address 0x18 are profile registers for modulation of frequency, phase, or amplitude. Register 0x04, Register 0x05, and Register 0x06 are dedicated registers for frequency, phase, and amplitude, respectively. These registers contain the initial frequency, phase offset and amplitude word. Frequency modulation is 32-bit resolution, phase modulation is 14 bit, and amplitude is 10 bit. When modulating phase or amplitude, the word value must be MSBaligned in the profile registers; excess bits are ignored. In Rev. A | Page 21 of 41 AD9911 Data Sheet modulation mode, bits CFR and FR1 configure the modulation type and level. See Table 6 and Table 7 for settings. Note that the linear sweep enable bit must be set to Logic 0 in modulation mode. Table 6. CFR 0 0 0 1 1 0 1 1 CFR x 0 0 0 4-Level Modulation—No RU/RD Description Modulation disabled Amplitude modulation Frequency modulation Phase modulation Modulation level bits are set to 01 (4-level). AFP bits are set to the desired modulation. RU/RD bits and the linear sweep bit are disabled. Table 10 displays how the profile pins are assigned. Table 10. 4-Level Modulation—No RU/RD Table 7. FR1 0 0 1 1 Profile Pin Configuration (PPC) Bits FR1 0 1 1 Description 2-level modulation 4-level modulation 8-level modulation 16-level modulation 0 1 0 1 When both modulation and the RU/RD feature are desired, unused profile pins or SDIO pins can be assigned. SDIO pins can only be used for RU/RD. Table 8. RU/RD Bits FR1 0 0 0 1 1 1 0 1 Description RU/RD disabled. Profile Pin 2 and Pin 3 configured for RU/RD operation. Profile Pin 3 configured for RU/RD operation. SDIO Pin 1, Pin 2, and Pin 3 configured for RU/RD operation. Forces the I/O to be used only in 1-bit mode. If profile pins are used for RU/RD, Logic 0 sets for ramp up and Logic 1 sets for ramp down. To support RU/RD flexibility, it is necessary to assign the profile pins and/or SDIO Pin 1 to Pin 3 to CH1 operation. This is controlled by the profile pin configuration (PPC) or PPC bits (FR1 ). The modulation descriptions that follow include data pin assignment. In the modulation descriptions, an “x” indicates that it does not matter. 2-Level Modulation—No RU/RD Modulation level bits are set to 00 (2-level). AFP bits are set to the desired modulation. RU/RD bits and the linear sweep bit are disabled. Table 9 displays how the profile pins are assigned. Table 9. 2-Level Modulation—No RU/RD Bits FR1 x x x As shown in Table 9, only Profile Pin P1 can be used to modulate CH1. If Pin P1 is Logic 0 and FSK modulation is desired, then Profile Register 0 (Register 0x04) frequency is chosen. If Pin P1 is Logic 1, then Profile Register 1 (Register 0x0A) frequency is chosen. P0 P1 P2 P3 N/A CH1 N/A N/A P0 CH1 P1 CH1 P2 N/A P3 N/A For this condition, the profile register chosen is based on the 2 bit value presented to profile pins . For example, if PPC = 011 and = 11, then the contents of Profile Register 3 (Register 0x0C) are presented to CH1 output. 8-Level Modulation—No RU/RD Modulation level bits are set to 10 (8-level). AFP bits are set to the desired modulation. RU/RD bits and the linear sweep bit are disabled. Table 11 shows the assignment of profile pins and channels. Table 11. 8-Level Modulation—No RU/RD Profile Pin Config. Bits FR1 x 0 1 P0 CH1 P1 CH1 P2 CH1 P3 x For this condition, the profile register (1 of 8) chosen is based on the 3-bit value presented to the Profile Pin P0 to Pin P2. For example, if PPC = x01 and = 111, then the contents of Profile Register 7 (Register 0x10) are presented to CH1 output. 16-Level Modulation—No RU/RD Modulation level bits are set to 11 (16-level). AFP bits are set to the desired modulation. RU/RD bits and the linear sweep bit are disabled. Table 12 displays how the profile pins and channels are assigned. Table 12. 16-Level Modulation—No RU/RD Profile Pin Config. (PPC) Bits FR1 x 0 1 P0 CH1 P1 CH1 P2 CH1 P3 CH1 For these conditions, the profile register chosen is based on the 4-bit value presented to Profile Pin P0 to Pin P3. For example, if PPC = x01 and = 1110, then the contents of Profile Register 14 (Register 0x17) are presented to CH1 output. 2-Level Modulation Using Profile Pins for RU/RD When the RU/RD bits = 01, either Profile Pin P2 or Pin P3 are available for RU/RD. Note that only a modulation level of two is available when RU/RD bits = 01. See Table 13 for available pin assignments. Rev. A | Page 22 of 41 Data Sheet AD9911 16-Level Modulation Using SDIO Pins for RU/RD Table 13. 2-Level Modulation—RU/RD Profile Pin Config. Bits FR1 0 0 0 P0 N/A P1 CH1 P2 N/A 0 CH1 N/A CH1 RU/RD 1 1 P3 CH1 RU/RD N/A 8-Level Modulation Using a Profile Pin for RU/RD RU/RD = 11 (SDIO Pin 1 available for RU/RD) and the level is set to 16. See the pin assignment shown in Table 18. Table 18. Profile Pin Config. Bits (FR1) x 0 1 P0 CH1 P1 CH1 P2 CH1 P3 CH1 SDIO_1 CH1 RU/RD SDIO_2 N/A SDIO_3 N/A When the RU/RD bits = 10, Profile Pin P3 is available for RU/RD. Note that only a modulation level of eight is available when the RU/RD bits = 10. See Table 14 for available pin assignments. Table 14. 8-Level Modulation—RU/RD For the configuration shown in Table 18, the profile register is chosen based on the 4-bit value presented to . For example, if PPC = x01 and = 1101, then the contents of Profile Register 13 (Register 0x16) are presented to CH1 output. The SDIO_1 pin provides the RU/RD function. Profile Pin Config. Bits FR1 x 0 1 LINEAR SWEEP (SHAPED) MODULATION MODE P0 CH1 P1 CH1 P2 CH1 P3 CH1 RU/RD SHIFT KEYING MODULATION USING SDIO PINS FOR RU/RD For RU/RD bits = 11, SDIO Pin 1, Pin 2, and Pin 3 are available for RU/RD. In this mode, modulation levels of 2, 4, and 16 are available. Note that the I/O port can only be used in 1-bit serial mode. Table 15. 2-Level Modulation Using SDIO Pins for RU/RD Profile Pin Config. Bits FR1 x x x P0 N/A P1 CH1 P2 N/A P3 N/A In this case, the SDIO pins can be used for the RU/RD function, as described in Table 16. Table 16. SDIO Pins 1 0 0 2 1 1 3 0 1 Description Triggers the ramp-up function for CH1 Triggers the ramp-down function for CH1 4-Level Modulation Using SDIO Pins for RU/RD For RU/RD = 11 (SDIO Pin 1 and Pin 2 are available for RU/RD), the modulation level is set to four. See Table 17 for pin assignments, including SDIO pin assignments. Table 17. Profile Pin Config. Bits (FR1) 0 0 0 P0 N/A P1 N/A P2 CH1 P3 CH1 SDIO_1 N/A 0 CH1 CH1 N/A N/A CH1 RU/RD 1 1 SDIO_2 CH1 RU/RD N/A SDIO_3 N/A N/A For the configuration shown in Table 17, the profile register is chosen based on the 2-bit value presented to or . For example, if PPC = 011, = 11, then the contents of Profile Register 3 (Register 0x0C) are presented to CH1 output. SDIO Pin 1 and Pin 2 provide the RU/RD function. Linear sweep enables the user to sweep frequency, phase, or amplitude from a starting point (S0) to an endpoint (E0). The purpose of linear sweep mode is to provide better bandwidth containment compared to direct modulation mode by enabling more gradual, user-defined changes between S0 and E0. Note that SYNC_CLK must be enabled when using Linear Sweep while the auxiliary DDS cores must be disabled. Digital power down (CSR bit ) of the auxiliary channels is recommended. Figure 41 depicts the linear sweep block diagram. In linear sweep mode, S0 is loaded into Profile Register 0 (Profile 0 is represented by Register 0x04, Register 0x05, or Register 0x06, depending on the parameter being swept) and E0 is always loaded into Profile Register 1 (Register 0x0A). If E0 is configured for frequency sweep, the resolution is 32-bits. For phase sweep, the resolution is 14 bits and for amplitude sweep, the resolution is 10 bits. When sweeping phase or amplitude, the word value must be MSB-aligned in Profile Register 1; unused bits are ignored. Profile Pin1 triggers and controls the direction (up/down) of the linear sweep for frequency, phase, or amplitude. The AD9911 can be programmed to ramp up or ramp down the output amplitude (using the 10-bit output scalar) before and after a linear sweep. If the RU/RD feature is desired, profile pins or SDIO_1:3 pins can be configured to control the RU/RD operation. For further details, refer to the Output Amplitude Control section. To enable linear sweep mode, AFP bits (CFR ), modulation level bits (FR1 ), and the linear sweep enable bit (CFR ) must be programmed. The AFP bits determine the type of linear sweep to be performed (see Table 19). The modulation level bits must be set to 00 (2-level). Table 19. AFP CFR 0 0 0 1 1 0 1 1 Rev. A | Page 23 of 41 Linear Sweep Enable CFR 1 1 1 1 Description N/A Amplitude sweep Frequency sweep Phase sweep AD9911 Data Sheet 32 Z–1 FREQ SWEEP EN 0 MUX PHASE OFFSET ADDER PHASE SWEEP EN 1 0 CTW0 MUX 15 COS(X) 10 AMP SWEEP EN 1 DAC 0 MUX 1 ACR CPW0 SWEEP FUNCTION LOGIC RU/RD LOGIC 05785-055 PHASE ACCUMULATOR Figure 41. Linear Sweep Capability Setting the Rate of the Linear Sweep The rate of the linear sweep is set by the intermediate step size (delta-tuning word) between S0 and E0 (see Figure 42) and the time spent (sweep ramp rate word) at each step. The resolution of the delta-tuning word is 32 bits for frequency, 14 bits for phase, and 10 bits for amplitude. The resolution for the delta ramp rate word is 8 bits. In linear sweep, the user programs a rising delta word (RDW, Register 0x08) and a rising sweep ramp rate word (RSRR, Register 0x07). These settings apply when sweeping from F0 to E0. The falling delta word (FDW, Register 0x09) and falling sweep ramp rate (FSRR, Register 0x07) apply when sweeping from E0 to S0. When programming, note that attention is required to prevent overflow of the sweep. If the sweep accumulator is allowed to overflow, an uncontrolled, continuous sweep operation occurs. To avoid this, the magnitude of the rising or falling delta word should be smaller than the difference between full scale and the E0 value (full scale − E0). For a frequency sweep, full scale is 231−1. For a phase sweep, full scale is 214 −1. For an amplitude sweep, full scale is 210−1. (FREQUENCY/PHASE/AMPLITUDE) LINEAR SWEEP The graph in Figure 42 displays a linear sweep up and then down using a profile pin. Note that the no dwell bit is cleared. If the no dwell bit (CFR) is set, the sweep accumulator returns to 0 upon reaching E0. For more information, see the Linear Sweep No Dwell Mode section. EO RDW ∆f,p,a RSRR ∆t TIME Figure 42. Linear Sweep Mode 05785-040 SO PROFILE PIN RDW f   32   SYNC _ CLK  2  (Hz) RDW ΔΦ   14   360  2  RDW a   10    2  DAC full-scale current The formula for calculating delta time from RSRR or FSRR is t  RSRR / SYNC _ CLK (Hz) At 500 MSPS operation (SYNC_CLK =125 MHz), the minimum time interval between steps is 1/125 MHz × 1 = 8 ns. The maximum time interval is (1/125 MHz) × 255 = 2.04 μs. Frequency Linear Sweep Example This section provides an example of a frequency linear sweep followed by a description. AFP CFR =10, modulation level FR1 = 00, sweep enable CFR = 1, linear sweep no-dwell CFR = 0. In linear sweep mode, when the profile pin transitions from low to high, the RDW is applied to the input of the sweep accumulator and the RSRR register is loaded into the sweep rate timer. When the profile pin transitions from high to low, the FDW is applied to the input of the sweep accumulator and the FSRR register is loaded into the sweep rate timer. FSRR ∆t The formulae for calculating the step size of RDW or FDW are The RDW accumulates at the rate given by the ramp rate (RSRR) until the output equals the CTW1 register value. The sweep is then complete and the output held constant in frequency. FDW ∆f,p,a For a piecemeal or a nonlinear transition between S0 and E0, the delta tuning words and ramp rate words can be reprogrammed during the transition. The FDW accumulates at the rate given by the ramp rate (FSRR) until the output equals the CTW0 register value. The sweep is then complete and the output held constant in frequency. See Figure 43 for the linear sweep circuitry. Figure 45 depicts a frequency sweep with no-dwell mode disabled. In this mode, the output follows the state of the profile Rev. A | Page 24 of 41 Data Sheet AD9911 pin. A phase or amplitude sweep works in the same manner with fewer bits. reverts to the S0 and stalls until high is detected on the profile pin. LINEAR SWEEP NO DWELL MODE Figure 44 demonstrates the no-dwell mode. The points labeled A indicate where a rising edge is detected on the profile pin. Points labeled B indicate at which points where the AD9911 has determined that the output has reached E0 and reverts to S0. To enable linear sweep no dwell mode, set CFR . The rising sweep is started by setting the profile input pin to 1. The frequency, phase or amplitude continues to sweep up at the rate set by the rising sweep ramp rate and the resolution set by the rising delta tuning word, until it reaches E0. The output then The falling ramp rate register and the falling delta word are unused in this mode. SWEEP ACCUMULATOR 0 FDW 0 N MUX RDW 0 N MUX N Z–1 N N 0 1 0 1 SWEEP ADDER MUX 0 1 MUX 1 N PROFILE PIN CTW0 RAMP RATE TIMER: 8-BIT LOADABLE DOWN COUNTER RATE TIME LOAD CONTROL LOGIC MUX FSRR PROFILE PIN N CTW1 1 05785-041 0 LIMIT LOGIC TO KEEP SWEEP BETWEEN S0 AND E0 ACCUMULATOR RESET LOGIC 8 RSRR Figure 43. Linear Sweep Block Circuitry (Frequency Sweep) fOUT B FTW1 A FTW0 B B A A SINGLE–TONE MODE PS = 0 PS = 1 PS = 0 PS = 1 PS = 0 Figure 44. Linear Sweep Mode Enabled—No Dwell Bit Set Rev. A | Page 25 of 41 PS = 1 05785-042 TIME AD9911 Data Sheet fOUT B FTW1 A FTW0 TIME PS = 0 LINEAR SWEEP MODE PS = 1 05785-043 SINGLE–TONE MODE PS = 0 Figure 45. Linear Sweep Enabled-No Dwell Bit Cleared SWEEP AND PHASE ACCUMULATOR CLEARING FUNCTIONS The AD9911 provides two different clearing functions. The first function is a continuous zeroing of the sweep logic and phase accumulator (clear and hold). CFR clears the sweep accumulator and CFR clears the phase accumulator The second function is a clear and release or automatic zeroing function. CFR is the automatic clear sweep accumulator bit and CFR is the automatic clear phase accumulator bit. Continuous Clear Bits The continuous clear bits are static control signals that, when high, hold the respective accumulator at 0. When the bit is programmed low, the respective accumulator is released. Clear and Release Bits The auto clear sweep accumulator bit, when set, clears and releases the sweep accumulator upon an I/O update or a change in the profile input pins. The auto clear phase accumulator, when set, clears and releases the phase accumulator upon an I/O update or a change in the profile pins. The automatic clearing function is repeated for every subsequent I/O update or change in profile pins until the clear and release bits are cleared via the I/O port. OUTPUT AMPLITUDE CONTROL The output amplitude may be controlled via one of four methods. Output amplitude control is implemented by the use of the 10-bit output scale factor (multiplier). See Figure 46 for output amplitude control configurations. For further details on the corresponding methods, see the Shift Keying Modulation section and the Linear Sweep (Shaped) Modulation Mode sections. The remaining methods (Manual and Automatic RU/RD) are described in this section. The RU/RD feature is used to control an on/off emission from the DAC. This helps reduce the adverse spectral impact of abrupt burst transmissions of digital data. The multiplier can be bypassed by clearing the multiplier enable bit (ACR = 0). Automatic and manual RU/RD modes are supported. The automatic mode generates a zero to full-scale (10-bits) linear ramp at a rate set using the amplitude ramp rate control register (ACR ). Ramp initiation and direction (up/down) is controlled using either the profile pins or the SDIO1:3 pins. See Table 21. Manual mode is selected by programming ACR = 10. In this mode, the user sets the output amplitude by writing to the amplitude scale factor value in the amplitude control register (Register 0x06 Bits ). Automatic RU/RD Mode Operation The automatic RU/RD mode is entered by setting ACR = 11. In this mode, the scale factor is internally generated and applied to the multiplier input port for scaling the output. The scale factor is the output of a 10-bit counter that increments/ decrements at a rate set by the 8-bit output ramp rate in Register 0x06 Bits . The scale factor increments if the external pin is high and decrements if the pin is low. The scale factor step size is selected using the ACR. Table 20 details the step size options available. Table 20. Autoscale Factor Step Size ASF (Binary) 00 01 10 11 Increment/Decrement Size 1 2 4 8 The amplitude scale factor register allows the device to ramp to a value less than full scale. Rev. A | Page 26 of 41 Data Sheet AD9911 AMPLITUDE MULTIPLIER ENABLE ACR DDS CORE 0 DAC 1 COS(X) 10 PROFILE/SDIO_1:3 PINS MUX PROFILE REGISTERS FOR ASK MODULATION TEST TONE MODULATION 10 SYNC_CLK 10 0 1 10 10 0 LOAD ARR TIMER BIT ACR AMPLITUDE RAMP RATE REGISTER (ACR BITS ) 0 1 8 AMPLITUDE SCALE FACTOR REGISTER (ACR) 10 2 10 INCREMENT/ DECREMENT STEP SIZE ACR MANUAL RAMP UP/DOWN (RU/RD) HOLD UP/DN INC/DEC EN LOAD DATA EN 10-BIT BINARY UP/DOWN COUNTER 8-BIT BINARY DOWN COUNTER OUT SYNC CLOCK 05785-054 LINEAR SWEEP ACCUMULATOR 10 AUTO RAMP UP/DOWN (RU/RD) RAMP UP/DOWN (RU/RD) ENABLE ACR Figure 46. Output Amplitude Control Configurations Ramp Rate Timer The ramp rate timer is a loadable 8-bit down counter. It generates the clock signal to the 10-bit counter, which in turn generates the internal scale factor. The formula for calculating the amplitude ramp rate time is t   x  / SYNC _ CLK(Hz) Where x is the decimal value in Register 00x06 Bits . At 500 MSPS operation (SYNC_CLK =125 MHz), the minimum time interval between steps is 1/125 MHz × 1 = 8 ns. The maximum time interval is (1/125 MHz) × 255 = 2.04 μs. The ramp rate timer is loaded with the value of the ASF every time the counter reaches 1 (decimal). This load and count down operation continues for as long as the timer is enabled unless the timer is forced to load before reaching a count of 1. If the load ARR timer bit ACR is set, the ramp rate timer is loaded if any of the following three incidents transpire: an I/O update occurs, a profile pin changes, or the timer reaches a See through Table 13 through Table 18 for RU/RD pin assignments. Rev. A | Page 27 of 41 AD9911 Data Sheet SYNCHRONIZING MULTIPLE AD9911 DEVICES The AD9911 allows easy synchronization of multiple AD9911 devices. At power-up, the phase of SYNC_CLK may be offset between multiple devices. There are three options (one automatic mode and two manual modes) to compensate for this offset and align the SYNC_CLK edges. These modes force the internal state machines of multiple devices to a common state, which aligns SYNC_CLKs. Any mismatch in REF_CLK phase between devices results in a corresponding phase mismatch on the SYNC_CLKs. OPERATION The first step is to program the master and slave devices for their respective roles. Configure the master device by setting its master enable bit (FR2 ). This causes the SYNC_OUT of the master device to output a pulse whose pulse width equals one system clock period and whose frequency equals ¼ of the system clock frequency. Configuring device(s) as slaves is performed by setting the slave enable bit (FR2 ). AUTOMATIC MODE SYNCHRONIZATION In automatic mode, synchronization is achieved by connecting the SYNC_OUT pin on the master device to the SYNC_IN pin of the slave device(s). Devices are configured as master or slave through programming bits, accessible via the I/O port. A configuration for synchronizing multiple AD9911 devices in automatic mode is shown in the Application Circuits section. In this configuration, the AD9510 provides coincident REF_CLK and SYNC_IN to all devices. In this mode, slave devices sample SYNC_OUT pulses from the master device and a comparison of all state machines is made by the auto-synchronization circuitry. If the slave device(s) state machines are not identical to the master, the slave device(s) state machines stall for one system clock cycle. This procedure synchronizes the slave device(s) within three SYNC_CLK periods. Delay Time Between SYNC_OUT and SYNC_IN When the delay between SYNC_OUT and SYNC_IN exceeds one system clock period, phase offset bits (FR2 ) are used to compensate. Without the compensation factor, a phase error of 90°, 180°, or 270° might exist. The default state of these bits is 00, which implies that the SYNC_OUT of the master and the SYNC_IN of the slave have a propagation delay of less than one system clock period. If the propagation time is greater than one system clock period, the time should be measured and the appropriate offset programmed. Table 21 describes the delays required per system clock offset value. Table 21. System Clock Offset Value 00 01 10 11 SYNC_OUT/SYNC_IN Propagation Delay 0 ≤ delay ≤ 1 1 ≤ delay ≤ 2 2 ≤ delay ≤ 3 3 ≤ delay ≤ 4 Automatic Synchronization Status Bit If a slave device falls out of sync, the sync status bit is set. This bit can be read through the I/O port bit (FR2 ). It clears automatically when read. If the device reacquires sync before the bit is read, the alarm will remain high. The bit does not necessarily reflect the current state of the device. The status bit can be masked by writing Logic 1 to the synchronization status mask bit (FR2 ). When masked, the bit is held low. MANUAL SOFTWARE MODE SYNCHRONIZATION The manual software mode is enabled by setting the manual synchronization bit (FR1 ). In this mode, the I/O update that resets the Manual SW synchronization bit stalls the state machine of the clock generator for one system clock cycle. Stalling the clock generation state machine by one cycle changes the phase relationship of SYNC_CLK between devices by one system clock period (90°). Note that the user may repeat this process until the devices have the corresponding SYNC_CLK signals in the desired phase relationship. The SYNC_IN input can be left floating since this input has an internal pull-up. The SYNC_OUT is not used. MANUAL HARDWARE MODE SYNCHRONIZATION Manual hardware mode is enabled by setting the manual SW synchronization bit (FR1 ). In this mode, the SYNC_CLK stalls by one system clock cycle each time a rising edge is detected on the SYNC_IN input. Stalling the SYNC_CLK state machine by one cycle changes the phase relationship of SYNC_CLK between devices by one system clock period (90°). Note that the process can be repeated until the devices have SYNC_CLK signals in the desired phase relationship. The SYNC_IN input can be left floating since this input has an internal pull-up. The SYNC_OUT is not used. Rev. A | Page 28 of 41 Data Sheet AD9911 I/O_UPDATE, SYNC_CLK, AND SYSTEM CLOCK RELATIONSHIPS I/O_UPDATE and SYNC_CLK are used together to transfer data from the I/O buffer to the active registers in the device. Data in the I/O buffer is inactive. SYNC_CLK is a rising edge active signal. It is derived from the system clock and a divide-by frequency divider of 4. The SYNC_CLK is provided externally to synchronize external hardware to the AD9911 internal clocks. If the set-up time between these signals is met, then constant latency (pipeline) to the DAC output exists. For example, if repetitive changes to phase offset via the SPI port is desired, the latency of those changes to the DAC output is constant, otherwise a time uncertainty of one SYNC_CLK period will be present. The I/O UPDATE is sampled on the rising edge of the SYNC_CLK. Therefore, I/O_UPDATE must have a minimum pulse width greater than one SYNC_CLK period. I/O_UPDATE initiates the start of a buffer transfer. It can be sent synchronously or asynchronously relative to the SYNC_CLK. The timing diagram shown in Figure 47 depicts when data in the I/O buffer is transferred to the active registers. The I/O UPDATE is set up and held around the rising edge of SYNC_CLK and has zero hold time and 4.8 ns setup time. SYSCLK A B SYNC_CLK I/O UPDATE DATA IN I/O BUFFERS N N–1 N N+1 N+1 N+2 THE DEVICE REGISTERS AN I/O UPDATE AT POINT A. THE DATA IS TRANSFERRED FROM THE ASYNCHRONOUSLY LOADED I/O BUFFERS AT POINT B. Figure 47. I/O_UPDATE Timing Rev. A | Page 29 of 41 05785-044 DATA IN REGISTERS AD9911 Data Sheet I/O PORT Three of the four data pins (SDIO_1:3) can be used for functions other than I/O port operation. These pins may be set to initiate a ramp-up or ramp-down (RU/RD) of the 10-bit amplitude output scalar. One of these pins (SDIO_3) may be used to provide the SYNC_I/O function. An I/O_UPDATE transfers data from the I/O port buffer to active registers. The I/O_UPDATE can either be sent for each communication cycle or when all I/O operations are complete. Data remains inactive until an I/O_UPDATE is sent, with the exception of the channel enable bits in the Channel Select Register (CSR). These bits require no I/O_UPDATE to be enabled. The maximum speed of the I/O port SCLK is 200 MHz. The maximum data throughput of 800 Mbps is achieved by using all SDIO_0:3 pins. tPRE tDSU There are four sets of addresses (0x03 to 0x18) that channel enable bits can access to provide channel independence when using the auxiliary DDS cores for either test-tone generation or spur killing. See the Control Register Descriptions section for further discussion of programming channels that are common or independent from one another. tSCLKPWH tDHLD SDIO SYMBOL tPRE tSCLK tDSU tSCLKPWH tSCLKPWL tDHLD DEFINITION CS SETUP TIME PERIOD OF SERIAL DATA CLOCK SERIAL DATA SETUP TIME SERIAL DATA CLOCK PULSE WIDTH HIGH SERIAL DATA CLOCK PULSE WIDTH LOW SERIAL DATA HOLD TIME MIN 1.0ns 5.0ns 2.2ns 2.2ns 1.6ns 0ns Figure 48. Set-Up and Hold Timing for the I/O Port CS There are two phases to a communications cycle. The first is the instruction phase, which writes the instruction byte into the AD9911. Each bit of the instruction byte is registered on each corresponding rising edge of SCLK. The instruction byte defines whether the upcoming data transfer is a write or read operation and contains the serial address of the address register. For example, when accessing Function Register 1, (FR1), which is three bytes wide, Phase 2 of the I/O cycle requires that three bytes are transferred. After transferring all data bytes per the instruction byte, the communication cycle is complete. tSCLKPWL SCLK I/O operation of the AD9911 occurs at the register level, not the byte level; the controller expects that all byte(s) contained in the register address are accessed. The SYNC_I/O function can be used to abort an I/O operation, thereby not allowing all bytes to be accessed. This feature can be used to program only a part of the addressed register. Note that only completed bytes are stored. Phase 2 of the I/O cycle is of the data transfer (write/read) between the I/O port controller and the I/O port buffer. The number of bytes transferred during this phase of the communication cycle is a function of the register being accessed. The actual number of additional SCLK rising edges required for the data transfer and instruction byte depends on the number of byte(s) in the register and the I/O mode of operation. tSCLK CS 05785-045 The AD9911 I/O port offers multiple configurations to provide significant flexibility. The I/O port includes an SPI-compatible mode of operation. Flexibility is provided by four data (SDIO_0:3) pins supporting four programmable modes of I/O operation. Upon completion of a communication cycle, the AD9911 I/O port controller expects the next set of rising SCLK edges to be the instruction byte for the next communication cycle. Data writes occur on the rising edge of SCLK. Data reads occur on the falling edge of SCLK. See Figure 43 and Figure 44. SCLK SDIO SDO (SDIO_2) tDV SYMBOL DEFINITION MIN tDV DATA VALID TIME 12ns 05785-046 OVERVIEW Figure 49. Timing Diagram for Data Read for I/O Port INSTRUCTION BYTE DESCRIPTION The instruction byte contains the information displayed in Table 22 where x = don’t care. Table 22. MSB R/Wb Rev. A | Page 30 of 41 D6 x D5 x D4 A4 D3 A3 D2 A2 D1 A1 LSB A0 Data Sheet AD9911 Bit 7 of the instruction byte (R/Wb) determines whether a read or write data transfer occurs after the instruction byte write. set indicates a read operation; Cleared indicates a write operation. Bit 4 to Bit 0 of the instruction byte determine which register is accessed during the data transfer portion of the communications cycle. The internal byte addresses are generated by the AD9911. I/O PORT PIN DESCRIPTION Data Clock (SCLK) The clock pin is used to synchronize data to and from the internal state machines of the AD9911. Chip Select (CS) The chip select pin allows more than one AD9911 device to be on the same communications lines. The chip select is an active low enable pin. Defined SDIO inputs go to a high impedance state when CS is high. If CS is driven high during any communications cycle, that cycle is suspended until CS is reactivated low. Data I/O (SDIO_0:3) Of the four SDIO pins, only the SDIO_0 pin is dedicated to this function. SDIO_1:3 can be used to control the ramping of the output amplitude. Bits in the channel select register (CSR Register 0x00) control the configuration of these pins. See the I/O Modes of Operation section for more information. I/O PORT FUNCTION DESCRIPTION Serial Data Out (SDO) The SDO function is available in single-bit (3-wire) mode only. In SDO mode, data is read from the SDIO_2 pin for protocols that use separate lines for reading and writing data (see Table 23 for pin configuration options). Bits in the CSR register (Register 0x00) control the configuration of this pin. The SDO function is not available in 2-bit and 4-bit I/O modes. SYNC_I/O The SYNC_I/O function is available in 1-bit and 2-bit modes. SDIO_3 serves as the SYNC_I/O pin, as configured by Bits in the CSR register (Register 0x00). Otherwise, the SYNC_I/O function is used to synchronize the I/O port state machines without affecting the addressable register contents. An active high input on the SYNC_I/O pin causes the current communication cycle to abort. After SDIO_3 returns low (Logic 0), another communication cycle can begin. The SYNC_I/O function is not available in 4-bit I/O mode. MSB/LSB TRANSFER DESCRIPTION The AD9911 I/O port supports either MSB or LSB first data formats. This functionality is controlled by CSR in the channel select register (CSR). MSB-first is the default. When CSR is set, the I/O port is LSB-first. The instruction byte must be written in the manner selected by CSR . Example To write the Function Register 1 (FR1) in MSB-first format, apply an instruction byte of MSB > 00000001 < LSB, starting with the MSB. The internal controller recognizes a write transfer of three bytes starting with the MSB, Bit , in the FR1 address (Register 0x01). Bytes are written on each consecutive rising SCLK edge until Bit is transferred. This indicates the I/O communication cycle is complete and the next byte is considered an instruction byte. To write the Function Register 1 (FR1) in LSB-first format, apply an instruction byte of MSB > 00000001 < LSB, starting with the LSB. The internal controller recognizes a write transfer of three bytes, starting with the LSB, Bit , in the FR1 address (Register 0x01). Bytes are written on each consecutive rising SCLK edge until Bit is transferred. Once the last data bit is written, the I/O communication cycle is complete and the next byte is considered an instruction byte. I/O MODES OF OPERATION There are four selectable modes of I/O port operation: • • • • Single-bit serial 2-wire mode (default mode). Single-bit, 3-wire mode. 2-bit mode. 4-bit mode (SYNC_I/O not available). Table 23 displays the function of all six I/O interface pins, depending on the mode of I/O operation selected. Table 23. I/O Port Pin Function vs. I/O Mode Pin Name SCLK CSB SDIO_0 SDIO_1 SDIO_2 SDIO_3 Single Bit, 2-Wire Mode I/O Clock Chip Select Data I/O Not used for SDIO1 Not used for SDIO1 SYNC_I/O Single Bit, 3-Wire Mode I/O Clock Chip Select Data In Not used for SDIO1 Serial Data Out (SDO) SYNC_I/O 2-Bit Mode I/O Clock Chip Select Data I/O Data I/O 4-Bit Mode I/O Clock Chip Select Not used for SDIO1 SYNC_I/O Serial Data I/O Serial Data I/O Data I/O Data I/O In this mode, these pins can be used for RU/RD operation. 1 The two bits, CSR , in the channel select register set the I/O mode of operation. These bits are defined as follows: CSR = 00. Single bit serial mode (2-wire mode) CSR = 01. Single bit serial mode (3-wire mode) CSR = 10. 2-bit mode CSR = 11. 4-bit mode Rev. A | Page 31 of 41 AD9911 Data Sheet Single-Bit Serial (2- and 3-Wire) Modes This reduces by 75% the number of cycles required to program the device. Note that when reprogramming the device for 4-bit mode, it is important to keep the SDIO_3 pin at Logic 0 until the device is programmed out of the single bit serial mode. Failure to do so can result in the I/O port controller being out of sequence. The single-bit serial mode interface allows read/write access to all registers that configure the AD9911. MSB-first or LSB-first transfer formats and the SYNC_I/O function are supported. In 2-wire mode, the SDIO_0 pin is the single serial data I/O pin. In 3-wire mode, the SDIO_0 pin is the serial data input pin and the SDIO_2 pin is the output. For both modes, the SDIO_3 pin is configured as an input and operates as the SYNC_I/O pin. The SDIO_1 pin is unused. Figure 50 through Figure 52 are write timing diagrams for the I/O modes available. Both MSB and LSB-first modes are shown. LSB-first bits are shown in parenthesis. The clock stall low/high feature shown is not required, but rather is used to show that data (SDIO) must have the proper setup time relative to the rising edge of SCLK. 2-Bit Mode The SPI port operation in 2-bit mode is identical to the SPI port operation in single bit mode, except that two bits of data are registered on each rising edge of SCLK, cutting in half the number of cycles required to program the device. The SDIO_0 pin contains the even numbered data bits using the notation D while the SDIO_1 pin contains the odd numbered data bits regardless of whether in MSB- or LSB-first format (see Figure 47). Figure 53 through Figure 56 are read timing diagrams for each I/O mode available. Both MSB and LSB-first modes are shown. LSB-first bits are shown in parenthesis. The clock stall low/high feature shown is not required. It is used to show that data (SDIO) must have the proper set-up time relative to the rising edge of SCLK for the instruction byte and the read data that follows the falling edge of SCLK. 4-Bit Mode The SPI port in 4-bit mode is identical to the SPI port in single bit mode, except that four bits of data are registered on each rising edge of SCLK. INSTRUCTION CYCLE DATA TRANSFER CYCLE CS I7 (I0) I6 (I1) I5 (I2) I4 (I3) I3 (I4) I2 (I5) I1 (I6) I0 (I7) D7 (D0) D6 (D1) D5 (D2) D4 (D3) D3 (D4) D2 (D5) Figure 50. Single-Bit Serial Mode Write Timing—Clock Stall Low INSTRUCTION CYCLE DATA TRANSFER CYCLE CS SCLK SDIO_1 I7 (I1) I5 (I3) I3 (I5) I1 (I7) D7 (D1) D5 (D3) D3 (D5) D1 (D7) SDIO_0 I6 (I0) I4 (I2) I2 (I4) I0 (I6) D6 (D0) D4 (D2) D2 (D4) D0 (D6) Figure 51. 2-Bit Mode Write Timing—Clock Stall Low Rev. A | Page 32 of 41 05785-048 SDIO_0 D1 (D6) D0 (D7) 05785-047 SCLK Data Sheet AD9911 INSTRUCTION CYCLE DATA TRANSFER CYCLE CS SDIO_3 I7 (I3) I3 (I7) D7 (D3) D3 (D7) SDIO_2 I6 (I2) I2 (I6) D6 (D2) D2 (D6) SDIO_1 I5 (I1) I1 (I5) D5 (D1) D1 (D5) SDIO_0 I4 (I0) I0 (I4) D4 (D0) D0 (D4) 05785-049 SCLK Figure 52. 4-Bit Mode Write Timing—Clock Stall Low DATA TRANSFER CYCLE INSTRUCTION CYCLE CS I7 (I0) SDIO_0 I6 (I1) I5 (I2) I4 (I3) I3 (I4) I2 (I5) I1 (I6) I0 (I7) D7 (D0) D6 (D1) D5 (D2) D4 (D3) D3 (D4) D2 (D5) D1 (D6) D0 (D7) 05785-050 SCLK Figure 53. Single-Bit Serial Mode (2-Wire) Read Timing—Clock Stall High DATA TRANSFER CYCLE INSTRUCTION CYCLE CS SCLK I7 (I0) I6 (I1) I5 (I2) I4 (I3) I3 (I4) I2 (I5) I1 (I6) I0 (I7) SDO DON'T CARE D7 (D0) (SDIO_2 PIN) D6 (D1) D5 (D2) D4 (D3) Figure 54. Single-Bit Serial Mode (3-Wire) Read Timing—Clock Stall Low Rev. A | Page 33 of 41 D3 (D4) D2 (D5) D1 (D6) D0 (D7) 05785-051 SDIO_0 AD9911 Data Sheet INSTRUCTION CYCLE DATA TRANSFER CYCLE CS SCLK I7 (I1) I5 (I3) I3 (I5) I1 (I7) D7 (D1) D5 (D3) D3 (D5) D1 (D7) SDIO_0 I6 (I0) I4 (I2) I2 (I4) I0 (I6) D6 (D0) D4 (D2) D2 (D4) D0 (D6) 05785-052 SDIO_1 Figure 55. 2-Bit Mode Read Timing—Clock Stall High INSTRUCTION CYCLE DATA TRANSFER CYCLE CS SDIO_3 I7 (I3) I3 (I7) D7 (D3) D3 (D7) SDIO_2 I6 (I2) I2 (I6) D6 (D2) D2 (I6) SDIO_1 I5 (I1) I1 (I5) D5 (D1) D1 (D5) SDIO_0 I4 (I0) I0 (I4) D4 (D0) D0 (D4) Figure 56. 4-Bit Mode Read Timing—Clock Stall High Rev. A | Page 34 of 41 05785-053 SCLK Data Sheet AD9911 REGISTER MAPS CONTROL REGISTER MAP Table 24. Register Name (Address) Channel Select Register (CSR) (0x00) Function Register 1 (FR1) (0x01) Function Register 2 (FR2) (0x02) 1 Bit Range Bit 0 (LSB) Default Value I/0 mode select LSB first 0xF0 Testtone enable Manual software synchronization 0x00 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Auxiliary Channel 3 (W/R enable 1) Auxiliary Channel 2 (W/R enable1) Primary Channel 1 (W/R enable1) Auxiliary Channel 0 (W/R enable1) Must be 0 Reference clock input power down External power down mode Sync clock disable DAC reference power down Open Open Profile pin configuration Ramp up/ramp down PLL divider ratio Bit 1 Manual hardware synchronization Modulation Level 0x00 VCO gain control Charge pump control 0x00 Multidevice synchronization slave enable Multidevice synchronization master enable Multidevice synchronization status Multidevice synchronization mask Open System clock offset 0x00 All channels auto clear sweep accumulator All channels clear sweep accumulator All channels auto clear phase accumulator All channels clear phase accumulator Open Open 0x00 Channel enable bits do not require an I/O update to be activated. These bits are active immediately after the byte containing the bits is written. All other bits need an I/O update to become active. The channel enable bits determine if the channel registers and/or profile registers are written to or not. Rev. A | Page 35 of 41 AD9911 Data Sheet CHANNEL REGISTER MAP Table 25. Register Name (Address) Channel Function 1 (CFR) (0x03) Bit Range Channel Frequency Tuning Word 01 (CTW0) (0x04) Channel Phase1 Offset Word 0 (CPOW0) (0x05) Amplitude Control (ACR) (0x06) Linear Sweep Ramp Rate1 (LSR) (0x07) LSR Rising Delta1 (RDW) (0x08) LSR Falling Delta1 (FDW) (0x09) Bit 7 (MSB) Digital powerdown Bit 6 DAC power down Linear sweep no-dwell Linear sweep enable Amplitude frequency phase select Bit 5 Matched pipe delays active Bit 4 Auto clear sweep accumulator Bit 3 Clear sweep accumulator Bit 2 Auto clear phase accumulator Load SRR at I/O Update Open Open Must be 0 Open Data align bits for SpurKiller mode Frequency Tuning Word 0 Frequency Tuning Word 0 Frequency Tuning Word 0 Frequency Tuning Word 0 Phase Offset Word 0 Phase Offset Word 0 Open Increment/decrement step size (LSB) Bit 0 Sine wave output enable DAC full-scale current control Bit 1 Clear phase accumulator 2 Open Amplitude scale factor Amplitude Ramp-up/ Load ARR at I/O multiplier ramp-down update enable enable Amplitude ramp rate Linear sweep rising ramp rate (RSRR) Linear sweep falling ramp rate (FSRR) Default Value 0x02 0x03 0x00 0x00 0x00 0x00 Amplitude scale factor 0x00 0x00 – – – Rising delta word – Rising delta word Rising delta word Rising delta word Falling delta word – – – – Falling delta word Falling delta word Falling delta word – – – There are four sets of channel registers and profile registers, one per channel. This is not shown in the channel or profile register maps because the addresses of all channel registers and profile registers are the same for each channel. Therefore, the channel enable bits determine if the channel registers and/or profile registers are written to or not. 2 The clear accumulator bit is set after a master reset. It self clears when an I/O update is asserted. 1 Rev. A | Page 36 of 41 Data Sheet AD9911 PROFILE REGISTER MAP Table 26. Register Name (address) Channel Word 1 (CTW1) (0x0A) Channel Word 2 (CTW2) (0x0B) Channel Word 3 (CTW3) (0x0C) Channel Word 4 (CTW4) (0x0D) Channel Word 5 (CTW5) (0x0E) Channel Word 6 (CTW6) (0x0F) Channel Word 7 (CTW7) (0x10) Channel Word 8 (CTW8) (0x11) Channel Word 9 (CTW9) (0x12) Channel Word 10 (CTW10) (0x13) Channel Word 11 (CTW11) (0x14) Channel Word 12 (CTW12) (0x15) Channel Word 13 (CTW13) (0x16) Channel Word 14 (CTW14) (0x17) Channel Word 15 (CTW15) (0x18) Bit Range MSB LSB Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Frequency tuning word or phase word or amplitude word Rev. A | Page 37 of 41 Default Value – – – – – – – – – – – – – – – AD9911 Data Sheet CONTROL REGISTER DESCRIPTIONS CHANNEL SELECT REGISTER (CSR) The CSR register determines if channels are enabled or disabled by the status of the channel enable bits. Channels are enabled by default. The CSR register also determines which mode and format (MSB-first or LSB-first) of operation is active. The CSR is comprised of one byte located in Register 0x00. synchronization feature is active. See the Synchronizing Multiple AD9911 Devices +section for details. FR1 Test-tone modulation enable. FR1 = 0 (default) disables and 1 enables. FR1 open. FR1 DAC reference power-down. CSR LSB-first CSR = 0 (default), the serial interface, accepts data in MSBfirst format. CSR = 1, the interface, accepts data in LSBfirst format. CSR I/O mode select FR1 = 0 (default). The DAC reference is enabled. FR1 = 1. DAC reference is disabled and powered down. FR1 SYNC_CLK disable. FR1 = 0 (default), the SYNC_CLK pin is active. CSR 00 = single bit serial (2-wire mode). 01 = single bit serial (3-wire mode). 10 = 2-bit mode. 11 = 4-bit mode. FR1 = 1. The SYNC_CLK pin assumes a static Logic 0 state (disabled). The pin drive logic is shut down. The synchronization circuitry remains active internally (necessary for normal device operation.) See the I/O Modes of Operation section for more details. FR1 external power-down mode. CSR = must be cleared to 0. FR1 = 0 (default). The external power-down mode is in the fast recovery power-down mode. When the PWR_DWN_CTL input pin is high, the digital logic and the DAC digital logic are powered down. The DACs bias circuitry, PLL, oscillator, and clock input circuitry are not powered down. CSR channel enable bits. CSR bits are active immediately once written. They do not require an I/O update to take effect. There are four sets of channel registers and profile registers, one per channel. This is not shown in the channel or profile register map. The addresses of all channel registers and profile registers are the same for each channel. Therefore, the channel enable bits distinguish the channel registers and profile registers values for each channel. FR1 = 1. The external power down mode is in the full power-down mode. When the PWR_DWN_CTL input pin is high, all functions are powered down. This includes the DAC and PLL, which take a significant amount of time to power up. For example, FR1 = 0 (default). The clock input circuitry is enabled for operation. FR1 = 1. The clock input circuitry is disabled and is in a low power dissipation state. CSR = 0010, only primary Channel 1 receives commands from the channel and profile registers. CSR = 0000, only auxiliary Channel 0 receives commands from the channel registers and profile registers. CSR = 0011, both Channel 0 and Channel 1 receive commands from the channel registers and profile registers. FR1 clock input power-down. FR1 modulation level bits. The modulation (FSK, PSK, and ASK) level bits control the level (2/4/8/16) of modulation to be performed. See Table 7 for settings. FR1 RU/RD bits. Function Register 1 (FR1) Description FR1 is comprised of three bytes located in Register 0x01. The FR1 is used to control the mode of operation of the chip. The functionality of each bit is detailed as follows: FR1 manual software synchronization bit. FR1 = 0 (default), the software manual synchronization feature is inactive. FR1 = 1.The manual software synchronization feature is active. See Synchronizing Multiple AD9911 Devices section for details. FR1 Manual hardware synchronization bit. FR1 = 0 (default), the manual hardware synchronization feature is inactive. FR1 = 1, the manual hardware The RU/RD bits control how the profile pins and SDIO_1:3 pins are assigned. See Table 8 for settings FR1 profile pin configuration bits. The profile pin configuration bits assign the profile and SDIO pins for the different tasks. See the Shift Keying Modulation section for examples. FR1 inactive. FR1 charge pump current control. FR1 = 00 (default), the charge pump current is 75 µA. = 01 charge pump current is 100 µA. = 10 charge pump current is 125 µA. = 11 charge pump current is 150 µA. Rev. A | Page 38 of 41 Data Sheet AD9911 FR1 PLL divider values. FR1 , if the value is > 3 and < 21, the PLL is enabled and the value sets the multiplication factor. If the value is < 4 or >20 the PLL is disabled. FR1 PLL VCO gain. FR1 = 0 (default), the low range (system clock below 160 MHz). FR1 = 1, the high range (system clock above 255 MHz). Function Register 2 (FR2) Description The FR2 is comprised of two bytes located in Address 0x02. The FR2 is used to control the various functions, features, and modes of the AD9911. The functionality of each bit is as follows: FR2 system clock offset. See the Synchronizing Multiple AD9911 Devices section for more details. FR2 inactive. FR2 . Multidevice synchronization bits. See the Synchronizing Multiple AD9911 Devices section for more details. CFR = 0 (default). The angle-to-amplitude conversion logic employs a cosine function. CFR = 1. The angle-toamplitude conversion logic employs a sine function. CFR Clear phase accumulator. CFR = 0 (default). The phase accumulator functions as normal. CFR = 1. The phase accumulator memory elements are asynchronously cleared. CFR auto clear phase accumulator. CFR = 0 (default). A new frequency tuning word is applied to the inputs of the phase accumulator, but not loaded into the accumulator. CFR = 1. This bit automatically synchronously clears (loads 0s) the phase accumulator for one cycle upon reception of the I/O_UPDATE sequence indicator. CFR clear sweep accumulator. CFR = 0 (default). The sweep accumulator functions as normal. CFR = 1. The sweep accumulator memory elements are asynchronously cleared. CFR auto clear sweep accumulator. CFR = 0 (default). A new delta word is applied to the input, as in normal operation, but not loaded into the accumulator. CFR = 1. This bit automatically synchronously clears (loads 0s) the sweep accumulator for one cycle upon reception of the I/O_UPDATE sequence indicator. FR2 inactive. FR2 Clear phase accumulator. FR2 = 0 (default), the phase accumulator functions as normal. FR2 = 1, the phase accumulator memory elements are asynchronously cleared. CFR match pipe delays active. FR2 Auto clear phase accumulator. FR2 = 0 (default). A new frequency tuning word is applied to the inputs of the phase accumulator, but not loaded into the accumulator. FR2 = 1. This bit automatically synchronously clears (loads zeros into) the phase accumulator for one cycle upon reception of the I/O update sequence indicator on both channels. CFR = 0 (default), match pipe delay mode is inactive. CFR = 1, match pipe delay mode is active. See the SingleTone Mode—Matched Pipeline Delay section for details. CFR DAC power-down. CFR = 0 (default). The DAC is enabled for operation. CFR = 1. The DAC is disabled and held in its lowest power dissipation state. CFR digital power-down. CFR = 0 (default). The digital core is enabled for operation. FR2 Clear sweep accumulator. CFR = 1. The digital core is disabled and is in its lowest power dissipation state. FR2 = 0 (default), the sweep accumulator functions as normal. FR2 = 1, the sweep accumulator memory elements are asynchronously cleared. CFR . DAC LSB control (see Table 5). FR2 Auto clear sweep accumulator. CFR = 00 (default). FR2 = 0 (default). A new delta word is applied to the input, as in normal operation, but not loaded into the accumulator. FR2 = 1. This bit automatically synchronously clears (loads 0s) the sweep accumulator for one cycle upon reception of the I/O_UPDATE sequence indicator on both channels. CFR must be cleared to 0. CHANNEL FUNCTION REGISTER (CFR) DESCRIPTION CFR Enable sine function. CFR linear sweep ramp rate load at I/O_UPDATE. CFR = 0 (default). The linear sweep ramp rate timer is loaded only upon timeout (timer = 1); it is not loaded by the I/O_UPDATE input signal. CFR = 1. The linear sweep ramp rate timer is loaded upon timeout (timer = 1) or at the time of an I/O_UPDATE input signal. CFR linear sweep enable. Rev. A | Page 39 of 41 AD9911 Data Sheet CFR = 0 (default). The linear sweep capability of the AD9911 is inactive. CFR = 1. The linear sweep capability of the AD9911 is active. The delta frequency tuning word is applied to the frequency accumulator at the programmed ramp rate. ACR = 1. The amplitude ramp rate timer is loaded upon timeout (timer =1) or at the time of an I/O_UPDATE input signal (or change in profile select bits). CFR linear sweep no-dwell. ACR = 0 (default). When ACR is active, Logic 0 on ACR enables the manual RU/RD operation. See the Output Amplitude Control section of this document for details. ACR = 1. If ACR is active, a Logic 1 on ACR enables the AUTO RU/RD operation. See the Output Amplitude Control section for details. CFR = 0 (default). The linear sweep no-dwell function is inactive. CFR = 1. The linear sweep no-dwell function is active. See the Linear Sweep (Shaped) Modulation Mode section for details. If CFR is clear, this bit is ignored. CFR Data align bits for SpurKiller mode. See the SpurKiller/Multitone Mode section for details. ACR auto RU/RD enable (only valid when ACR is active high). ACR amplitude multiplier enable. CFR inactive. CFR amplitude/frequency/phase select controls, the type of modulation is to be performed for that channel. See the Shift Keying Mode section for examples. ACR = 0 (default). Amplitude multiplier is disabled. The associated clocks are stopped for power saving; the data from the DDS core is routed around the multipliers. ACR = 1, amplitude multiplier is enabled. Channel Frequency Tuning Word 0 (CFTW0) Description ACR inactive. CFTW0 Frequency Tuning Word 0 for each channel. Channel Phase Offset Word 0 (CPOW0) Description ACR amplitude increment/decrement step size. See Table 20 for details. CPOW0 Phase Offset Word 0 for each channel. ACR amplitude ramp rate value. CPOW0 inactive. Channel Linear Sweep Register (LSR) Description Amplitude Control Register (ACR) Description LSR linear sweep rising ramp rate. ACR amplitude scale factor. Channel Linear Sweep Rising Delta Word Register (RDW) Description ACR amplitude ramp rate load control bit. ACR = 0 (default). The amplitude ramp rate timer is loaded only upon timeout (timer = 1) and is not loaded by an I/O_UPDATE input signal (or change in the profile select bits). RDW 32-bit rising delta tuning word. Channel Linear Sweep Falling Delta Word Register (FDW) Description FDW 32-bit falling delta tuning word. Rev. A | Page 40 of 41 Data Sheet AD9911 OUTLINE DIMENSIONS 0.30 0.23 0.18 0.60 MAX 0.60 MAX 43 1 42 PIN 1 INDICATOR 7.85 7.75 SQ 7.65 0.50 BSC 6.25 6.10 SQ 5.95 EXPOSED PAD 29 TOP VIEW 1.00 0.85 0.80 SEATING PLANE 0.80 MAX 0.65 TYP 12° MAX 0.50 0.40 0.30 14 28 15 BOTTOM VIEW 0.25 MIN 6.50 REF 0.05 MAX 0.02 NOM COPLANARITY 0.20 REF 0.08 SIDE VIEW PIN 1 INDICATOR 56 FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-VLLD-2 06-07-2012-A 8.10 8.00 SQ 7.90 Figure 57. 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 8 mm × 8 mm Body, Very Thin Quad (CP-56-1) Dimensions shown in millimeters ORDERING GUIDE Model 1 AD9911BCPZ AD9911BCPZ-REEL7 AD9911/PCB 1 Temperature Range –40°C to +85°C –40°C to +85°C Package Description 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] Evaluation Board Z = RoHS Compliant Part.. ©2006–2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05785-0-11/16(A) Rev. A | Page 41 of 41 Package Option CP-56-1 CP-56-1