1 GSPS Quadrature Digital
Upconverter with 14-Bit DAC
EVAL-AD9957
FEATURES
GENERAL DESCRIPTION
1 GSPS internal clock speed (up to 400 MHz analog output)
Integrated 1 GSPS 14-bit DAC
250 MHz I/Q data throughput rate
Phase noise ≤ −125 dBc/Hz (400 MHz carrier @ 1 kHz offset)
Excellent dynamic performance >80 dB narrow-band SFDR
8 programmable profiles for shift keying
Sin(x)/(x) correction (inverse sinc filter)
Reference clock multiplier
Internal oscillator for a single crystal operation
Software and hardware controlled power-down
Integrated RAM
Phase modulation capability
Multichip synchronization
Easy interface to Blackfin SPORT
Interpolation factors from 4× to 252×
Interpolation DAC mode
Gain control DAC
Internal divider allows references up to 2 GHz
1.8 V and 3.3 V power supplies
100-lead TQFP_EP package
This data sheet serves as a guide to setup and use the AD9957
evaluation board. The AD9957 is a 1 GSPS quadrature digital
upconverter with a 14-bit DAC.
The evaluation board software provides a graphical user
interface for easy communication with the device along with
many user-friendly features such as the mouse-over effect,
which clarifies elements by hovering the mouse over the
element.
Use this data sheet in conjunction with the AD9957 data sheet,
available from Analog Devices, Inc., at www.analog.com.
PACKAGE CONTENTS
AD9957 evaluation board
AD9957/PCB installation software
USB cable
FUNCTIONAL BLOCK DIAGRAM
MODULATION
DATA
TO PC
USB
INTERFACE
EVAL-AD9957
FIFO
SPI
DC POWER
HEADER
MULTICHIP
SYNC
AD9957
REFERENCE
CLOCK
DAC OUT
07801-001
BASEBAND
I/Q DATA
Figure 1.
Rev. 0
Evaluation boards are only intended for device evaluation and not for production purposes.
Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or
statutory including, but not limited to, any implied warranty of merchantability or fitness for a
particular purpose. No license is granted by implication or otherwise under any patents or other
intellectual property by application or use of evaluation boards. Information furnished by Analog
Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result
from its use. Analog Devices reserves the right to change devices or specifications at any time
without notice. Trademarks and registered trademarks are the property of their respective owners.
Evaluation boards are not authorized to be used in life support devices or systems.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
www.analog.com
Tel: 781.329.4700
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
EVAL-AD9957
TABLE OF CONTENTS
Features .............................................................................................. 1
SDPSK .......................................................................................... 19
General Description ......................................................................... 1
Simulator ......................................................................................... 20
Package Contents .............................................................................. 1
Simulator Tool................................................................................. 21
Functional Block Diagram .............................................................. 1
Overview ..................................................................................... 21
Revision History ............................................................................... 2
Simulator Activation .................................................................. 21
Evaluation Board Hardware ............................................................ 3
Simulator Description ............................................................... 21
Requirements ................................................................................ 3
Single-Tone Mode Simulation .................................................. 23
Setting up the Evaluation Board ................................................. 3
QDUC Parallel Data Mode Simulation ................................... 24
Evaluation Board Software .............................................................. 5
QDUC BlackFin (Serial Data) Mode Simulation................... 24
Installing the Software ................................................................. 5
Interpolating DAC Mode Simulation ...................................... 25
Installing the Driver ..................................................................... 5
Virtual Oscilloscope and Spectrum Analyzer ........................ 25
Launching the Program ............................................................... 5
User Data File(s) ......................................................................... 25
Feature Windows .............................................................................. 7
Auxiliary Control File ................................................................ 26
Control ........................................................................................... 7
Keywords ......................................................................................... 27
Profiles.............................................................................................. 10
Debug ........................................................................................... 27
Profiles Windows........................................................................ 10
Showclip....................................................................................... 27
View Windows ............................................................................ 14
Samples ........................................................................................ 27
QDUC RAM Control................................................................. 14
DDSCORE................................................................................... 27
FIFO Control .............................................................................. 15
RSET............................................................................................. 27
MultiChip Sync Control ............................................................ 15
DACXFR ...................................................................................... 27
GPIO ............................................................................................ 16
FFTWINDOWTYPE................................................................. 27
Debug Window ........................................................................... 16
Register Map (Software Buffer) Values Window ................... 17
Virtual Oscillope and Spectrum Analyzer Instruments
Keywords ..................................................................................... 28
DUT I/O ...................................................................................... 17
DAC Output Signal Keywords.................................................. 29
Modulation Vector Generator....................................................... 18
Ordering Information .................................................................... 32
QAM............................................................................................. 18
Ordering Guide .......................................................................... 32
GMSK/EDGE .............................................................................. 19
ESD Caution................................................................................ 32
REVISION HISTORY
7/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 32
EVAL-AD9957
EVALUATION BOARD HARDWARE
REQUIREMENTS
Device Clock Oscillator Options
To use the evaluation board and run the software, the
requirements listed in Table 1 must be met.
The AD9957 architecture provides the user with three options
when providing an input signal to the part. The first option allows
the user to provide a high frequency input signal, connected to J1.
The second option allows the user to connect the part using a
lower input reference frequency, enabling the clock multiplier,
connected through J1. The third option allows the user to
connect a crystal resonator on the backside of the board.
Table 1. EVAL-AD9957 Requirements
Item
Operating System
Processor
Memory
Ports
Clocking
Requirement
Windows® 98/ME/2000/XP
Pentium® I or better
128 MB or better
One USB port
Signal generator capable of generating
sinusoidal waves of at least 0 dBm power,
up to at least 10 MHz
Capability to generate at least two
independent dc voltages (1.8 V/3.3 V)
Appropriate measurement device, such as a
spectrum analyzer or a high bandwidth
oscilloscope
USB 1.1/2.0 cable, and SMA-to-x cables (x =
SMA or BNC, depending on the connector
of the device interfacing with the board)
Power Supplies
Measurement
Cables
Note that the AD9957 does not populate the PLL loop filter
components. Therefore, to use the internal PLL of the AD9957 ,
the user must solder down these components, or else the PLL is
not stable. The AD9957 data sheet has helpful formulas to
calculate the appropriate values.
To enable the crystal mode, switch the jumper, W7, to the XTAL
mode. Remove C51 and C52. Place 0 Ω resistors at R4 and R11
on the backside of the board. The crystal oscillates at 25 MHz.
Refer to the AD9957 data sheet for details on the maximum
input speeds and input sensitivities of these two inputs.
Device Communication Requirements
Two interface standards are available on the evaluation board:
SETTING UP THE EVALUATION BOARD
DC Power Supply
•
•
The AD9957 evaluation board has two power supply connectors
(four pins each): TB1 and TB2. TB1 powers the USB interface
circuitry, the digital I/O interface, and the digital core. TB2
powers the DAC and the clock input circuitry.
Analog Devices provides a GUI for the PC but does not provide
control software for external controllers.
Table 2 shows the necessary connections and the appropriate
biasing voltage for TB1 and TB2.
Use the jumper settings listed in Table 3 to enable different
modes of communication.
Table 2. Connections and Biasing Voltage
Table 3. Jumper Settings for Communication Modes
Connector
TB1
TB1
TB1
TB1
TB2
TB2
TB2
Pin No.
1
2
3
4
1, 3
2
4
Label
VCC
GND
DVDD_IO
DVDD
GND
DAC_VDD
CLK_VDD
Voltage (V)
3.3
0
3.3
1.8
0
3.3
1.8
USB 1.1/2.0
A header row (U5 and U9), which places the part under
the control of an external controller (such as a microprocessor,
FPGA, or DSP).
Mode
PC Control, USB Port
External Control
Settings
Set Jumper W1 and Jumper W2 to
enable.
Set Jumper W4 to EN.
Place a jumper on W5, W6, and W3.
Set Jumper W1 and Jumper W2 to
disable.
Set Jumper W4 to DIS.
Remove the jumper on W5, W6, and W3.
Jumper W1, Jumper W2, and Jumper W4 enable the USB
circuitry to control the AD9957. Jumper W3 controls the
EEPROM and is used in starting up the USB circuitry. Jumper
W5 and Jumper W6 control the signals SDO and SDIO to and
from the AD9957.
Rev. 0 | Page 3 of 32
EVAL-AD9957
REFERENCE
CLOCK
INPUT
DAC OUTPUT
07801-002
POWER SUPPLY
CONNECTIONS
MANUAL I/O
CONTROL HEADERS
Figure 2. Evaluation Board Layout
Manual I/O Control Headers
Clock Mode Select
Header connectors (U5, U6, and U9) provide the communication interface for the AD9957 when the part is under the
command of an external controller (see Table 3 for the correct
jumper settings).
Clock mode select controls whether the reference clock source
is a 20 MHz to 30 MHz crystal or an external signal generator.
A 25 MHz crystal is provided on underside of the AD9957
evaluation board.
Multidevice Synchronous Control
Reference Clock Input
J2, J5, J6, and J7 connections are used to set up the AD9957
for multidevice synchronous operation.
The reference clock input is the input for the external reference
clock signal.
DAC Output
Power Supply Connections
The J4 connection is the filtered output of the DAC and J3
represents the unfiltered (default) DAC output. To enable
the filtered path, R19 on the PCB must be installed.
These two connectors, TB1 and TB2, provide all the necessary
supply voltages needed by the AD9957 and the evaluation board
(see Table 2).
USB Port
When the part is under PC control (default mode), the evaluation
board communicates with the AD9957 via the USB port.
Rev. 0 | Page 4 of 32
EVAL-AD9957
EVALUATION BOARD SOFTWARE
INSTALLING THE SOFTWARE
Windows XP Users
Use the following steps to install the AD9957 evaluation
software:
1.
2.
1.
2.
3.
3.
4.
5.
Log into your PC system with administrative privileges.
Uninstall any previous versions of the AD9957 evaluation
software from your PC system.
Insert the AD9957 evaluation software CD. Do not connect
the AD9957 evaluation board to the computer until the
AD9957 evaluation software has been installed.
Open the Readme.txt file located in the Software folder
before proceeding with the installation of the AD9957
evaluation software.
Run the setup.exe file located in the Software folder and
follow the on-screen installation instructions.
INSTALLING THE DRIVER
4.
5.
6.
7.
8.
Once the software has been installed onto your PC, interface
the AD9957 evaluation software to the AD9957 evaluation
board via the USB port (see Figure 2).
Power up the AD9957 evaluation board (see Table 2).
Connect the evaluation board to the computer using a USB
cable via the USB port. Then, the VBUS LED (CR1 on the
AD9957 evaluation board) illuminates.
When the USB cable is connected, the Found New
Hardware Wizard appears. Click Next to continue.
The AD9957 Firmware Loader appears.
Click Continue Anyway when the Hardware Installation
warning window appears.
Click Finish in the Found New Hardware Wizard when
the install is complete.
Click Next when the next Found New Hardware Wizard
appears.
Click Continue Anyway when the Hardware Installation
warning window appears.
Click Finish in the Found New Hardware Wizard when
the install is complete.
Once this screen has disappeared, the USB status LED (CR2 on
AD9957 evaluation board) should be flashing, indicating that the
evaluation board is properly connected. If the LED does not flash,
verify that all power and USB connections are properly connected.
In order for the evaluation board and software to communicate
properly, drivers must be loaded onto your PC system. Use the
instructions in the following sections to install these drivers on
your PC system.
Installing the Simulator
Windows 98/ME/2000 Users
1.
1.
2.
2.
3.
4.
Power up the AD9957 evaluation board (see Table 2).
Connect the evaluation board to the computer using a
USB cable via the USB port; the VBUS LED (CR1 on the
AD9957 evaluation board) illuminates.
When the USB cable is connected, the Found New
Hardware window appears.
Click Finish in the Found New Hardware Wizard when
the install is complete.
After the window has disappeared, the USB status LED (CR2 on
the AD9957 evaluation board) flashes, which indicates that the
evaluation board is connected properly.
3.
Run Setup.exe in the software MLRT73 installer directory
on the CD.
Follow the on screen instructions for installing the
simulator.
The simulator can be accessed from the AD9957
evaluation board software. See the Simulator Activation
section for further information.
LAUNCHING THE PROGRAM
Follow these steps to load the AD9957 evaluation software:
1.
2.
3.
Before starting the software, make sure that the AD9957
evaluation board is powered up, connected to the
computer, and that the USB status LED is flashing.
Click the Start button.
Select Programs > AD9957 Eval Software folder, >
AD9957 Eval Software to load the software.
A status message appears. See the Status Messages upon
Loading Software section for more information.
Rev. 0 | Page 5 of 32
EVAL-AD9957
Status Messages upon Loading Software
Once the AD9957 evaluation software has been loaded, a green
splash screen appears. The status box within the splash screen
gives the status of the AD9957 evaluation software. Green
writing in the status box indicates that the software has loaded
(see Figure 3). The status box disappears following a successful
load.
Most status message errors are resolved by checking jumper
settings, making sure that the evaluation board is powered up
correctly, and inspecting the USB port and cable connections.
In addition, check that the clock input source is connected and
properly configured.
07801-003
A splash screen with red writing in the status box indicates that
the software did not load and that an error occurred. Click
within this box to create a cursor. Scrolling up through the
status box with the cursor indicates why the software did not
load correctly.
Figure 3. Successful Load
Rev. 0 | Page 6 of 32
EVAL-AD9957
07801-004
FEATURE WINDOWS
Figure 4. Chip Level Control Window
Load
I/O updates can be sent manually (Manual I/O Update) or
automatically (Auto I/O Update) (see Figure 3). By default, the
AD9957 evaluation software is set to Auto I/O Update. When
LOAD is clicked, an I/O update signal is automatically sent to
the device. If synchronization across channels is desired, use the
Manual I/O Update button. To send an I/O update, uncheck
the Auto I/O Update box at the top of the screen and press the
I/O Update button.
The LOAD button is used to send data to the AD9957 device.
All LOAD buttons found in the evaluation software have the
same functionality.
The Show Warnings check box in Figure 4 can be selected
to show when you have entered data that exceeds the specifications of the AD9957.
CONTROL
The Control window provides control of the clock input, clock
multiplier, DAC gain settings, internal I/O update, and power
down functions of the AD9957. The following sections describe
the chip level control window portions as they appear in
Figure 4.
When new data is detected, LOAD flashes orange, indicating
that you need to click LOAD to send the updates to the serial
I/O buffer where they are stored until an I/O update is issued.
The I/O update sends the contents of the serial I/O buffer to
active registers.
Rev. 0 | Page 7 of 32
EVAL-AD9957
Clock
Operating Mode
The Clock section allows you to configure the reference clock
path in the AD9957.
The Operating Mode selector allows you to select between
the three operating modes of the AD9957. Quadrature
Modulation is the default setting. This puts the AD9957 into
quadrature digital up-converter (QDUC) mode. QDUC mode
takes digital baseband data and upconverts it to a specified IF
output. Single tone allows you to get a single tone output from
the AD9957. Single tone mode allows you to select a single
output frequency. Interpolating DAC keeps baseband data at
baseband but can change the sample rate of the data. See the
AD9957 data sheet for more information about the different
modes of operation.
External Clock inputs the operating frequency of the external
reference clock or crystal. The maximum reference clock frequency of the AD9957 is 1 GHz. A red outline indicates that
the value entered is out of range.
The ÷2 Divider Disable checkbox disables the input divider for
the clock path. The maximum frequency of this divider is 2 GHz.
The Enable Multiplier section selects the PLL multiplication
factor (12× to 127×) which is used to scale the input frequency.
The default setting of this box is disabled, indicating that the
reference clock multiplier circuitry is bypassed and the reference clock/crystal input is piped directly to the DDS core.
CP Current selects the charge pump current output of the
PLL in the reference clock multiplier circuitry. Selecting a
higher current output results in the loop locking faster,
but there is a trade-off. Increasing this current output also
increases phase noise.
Internal I/O Update
The Use Internal IO Update check box sets the I/O update pin
to an output. This output generates an active high pulse when
the internal I/O update occurs. The rate of the internal I/O
update can be programmed through the serial port. See the
AD9957 data sheet for more information.
Modulation Options
The VCO Range menu allows you to select the range of operation for the VCO on the AD9957. The AD9957 evaluation
software automatically determines which range the AD9957
should operate in. However, if you to run a given frequency in
a band other than the one selected by the software, a warning
box prompts you to confirm this. Note that using a VCO frequency outside of its specified range may result in undesired
operation, including nonfunctionality. See the AD9957 data
sheet for more information regarding the different VCO bands.
The XTAL Out drop-down menu selects the output drive
strength of the XTAL reference output. There are three drive
strengths: low, middle, and high.
The Data Format selection allows you to select the formatting
method of the input data either from Two’s Complement or
Offset Binary.
The Invert TX Enable check box allows you to invert the
polarity of the TxENABLE signal.
The Enable PDCLK check box allows you to control the
PDCLK functionality.
The Invert PDCLK box allows you to invert the polarity of
the PDCLK signal.
The PDClk = ½ Input Data Rate box allows you to set the
PDCLK signal to ½ of the input data rate.
The Data Assembler Holds Last Value box allows you to
choose between the data assembler, which outputs all zeros
or the last value received when TxENABLE is low.
PLL Lock indicates when the PLL is in a valid lock state. If
the PLL loses lock, the indicator light display lights up or
turns green.
Activate BFI
System Clock displays the operating frequency the DDS
core (system). The value shown here is derived from the
values entered in the External Clock and Multiplier boxes.
Using the Active BFI control allows you to make the AD9957
data compatible with an Analog Devices, Inc., Blackfin® DSP.
Refer to the AD9957 data sheet for more information regarding
clock modes and operation.
The Bit Order section allows you to specify the input format
of LSB or MSB first.
AUX DAC Control
The Early Frame Sync Enable box changes the BFI
compatibility to late frame or early frame.
The DAC Gain Ctrl drop-down menu controls the auxiliary
DAC setting to select the full-scale output current of the DAC.
See the AD9957 data sheet for more information about DAC
gain setting.
The DAC Iout box displays the full-scale output current of
the DAC. This number is based on a DAC_RSET resistor
value of 10 kΩ.
Rev. 0 | Page 8 of 32
EVAL-AD9957
Power Down
Sync Sample Error
The Digital, DAC, Clock Input, and Aux. DAC power-down
controls allow you to power down each of the specific circuit
blocks individually.
The Sync Sample Error section allows you to enable/disable
the sync sample error detection using the bit provided. If a
sync error is detected, the external flag is set.
Setting the Enable Auto PD box enables the condition when
the TxENABLE pin is Logic 0, the baseband signal processing
chain is flushed of residual data, and the clocks are automatically stopped. Clocks restart when the TxENABLE pin is a
Logic 1. The enable auto PD bit does nothing when it is cleared.
Other Controls
The External PD Mode section allows you to control which
power-down mode is used in conjunction with the external
power-down pin. The Fast Recovery mode sets the AD9957
into a power-down state that keeps clocks running and bias
circuits active but does not allow the part to output data. This
mode uses significantly more power than Full Power Down
mode. Full Power Down mode stops clocks and powers down
bias circuits. It takes significantly longer to power back up from
power-down state.
The Enable I/O Sync Clock Output Pin box allows you to
enable/disable the output driver for the I/O sync clock output.
The Enable Matched Latency box allows you to align the
application of the frequency tuning word, phase offset word,
and amplitude scale factor at the same time. If this bit is cleared,
then those words are applied at different times.
The Auto Clear Phase Accumulator box sets the DDS phase
accumulator to a reset state when the I/O_UPDATE pin is set
high or when a profile changes.
The Clear Phase Accumulator box holds the DDS phase
accumulator in a reset state as long as the clear phase
accumulator bit is set.
The External Power Down Pin button allows you to control the
external power-down pin without having to alter the evaluation
board. See the AD9957 data sheet for more information about
full power-down conditions.
Rev. 0 | Page 9 of 32
EVAL-AD9957
07801-005
PROFILES
Figure 5. Profiles Control Window for QDUC Modulation Mode
PROFILES WINDOWS
The Profiles window allows you to change the different profile
settings easily. Figure 5 to Figure 7 show the profile control
windows for the three operating modes of the AD9957:
QDUC modulation mode, single-tone mode, and interpolating DAC mode.
QDUC Modulation Mode
Output Freq is used to set the frequency generated by the DDS.
This is the IF carrier to which the unconverted modulation data
is applied.
Phase Offset controls the phase of the DDS output. This can
be changed from 0° to 360° with 16-bit resolution.
Output Scale Factor digitally controls the amplitude of the
carrier from the DDS. This scalar has 8-bits of resolution.
Note that this can be used in conjunction with DAC Gain Ctrl
(see Figure 4) to increase the flexibility of the output amplitude.
CCI Interpolation Rate is the upconversion rate through the
cascaded comb integrator (CCI) filters on the AD9957. This can
vary from 1 to 63 using a 6-bit control word. Note that this is
not the only source of interpolation. See the AD9957 data sheet
for more information on interpolation.
Inverse CCI Bypass allows you to enable or disable the inverse
CCI filter. This filter predistorts the data coming into the CCI
section to compensate for a slight attenuation gradient caused
by the CCI filter.
Spectral Inversion allows you to change the orientation of the
modulated signal with respect to the carrier.
Rev. 0 | Page 10 of 32
07801-006
EVAL-AD9957
Figure 6. Profile Control Window for Single-Tone Mode
Single-Tone Mode
Output Freq is used to set the frequency generated by the
DDS. In the case of a single tone output, the AD9957 generates
a sine/cosine wave at this output frequency.
Amplitude SF digitally controls the amplitude of the carrier
from the DDS. This scalar has 14-bits of resolution. Note that
this can be used in conjunction with DAC Gain Ctrl to increase
the flexibility of the output amplitude. The Enable Profile ASF
must be checked to use this control.
Phase Offset controls the phase of the DDS output. This can be
changed from 0° to 360° with 16-bit resolution.
Rev. 0 | Page 11 of 32
07801-007
EVAL-AD9957
Figure 7. Profile Control Window for Interpolating DAC Mode
Interpolating DAC Mode
Output Freq and Phase Offset are not available in interpolating
DAC mode. There is no DDS output frequency when using this
mode. This mode can resample the baseband data to a different
data rate, but does not perform any upconversion.
CCI Interpolation Rate is the upconversion rate through the
cascaded comb integrator (CCI) filters on the AD9957. This
can vary from 1 to 63 using a 6-bit control word.
Inverse CCI Bypass allows you to enable or disable the inverse
CCI filter. This filter predistorts the data coming into the CCI
section to compensate for a slight attenuation gradient caused
by the CCI filter.
Data Entry Windows
07801-008
Output Scale Factor digitally controls the amplitude of the
carrier from the DDS. This scalar has eight bits of resolution.
Note that this can be used in conjunction with DAC Gain Ctrl
to increase the flexibility of the output amplitude.
Figure 8. Edit Output Frequency Pop-Up Window
The Edit Phase Offset window (see Figure 9) appears by
double-clicking the Phase Offset data entry form. The Edit
Phase Offset window allows you to set individual bits in the
phase offset tuning word. These can be entered in using dec,
hex, or binary format. This window also allows you to enter in a
tuning word and see the correct dec, hex, or binary representations for this word. You can scroll through the Phase Offset
form to view the different tuning words one bit at a time.
07801-009
The Edit output frequency window (see Figure 8) appears by
double-clicking the Output Freq data entry form. The Edit
output frequency window allows you to set individual bits in
the frequency tuning word. These can be entered by using dec,
hex, or binary format. This window also allows you to enter in a
tuning word and see the correct dec, hex, or binary representations for this word. You can scroll through the Frequency form
to view the different tuning words one bit at a time.
Figure 9. Edit Phase Offset Pop-Up Window
Rev. 0 | Page 12 of 32
EVAL-AD9957
Edit Output Scale Factor window (see Figure 10) appears by
double-clicking the Output Scale Factor data entry form. The
Edit Output Scale Factor window allows you to set individual
bits in the output scale factor tuning word. These can be entered
in using dec, hex, or binary. This window also allows you to
enter in a tuning word and see the correct dec, hex, or binary
representations for this word. You can scroll the Output Scale
Factor to view the different tuning words one bit at a time.
Other Controls and CCI Overflow/Clear
The Q First Data Pairing check box selects between applying
I-data followed by Q-data or Q-data followed by I-data.
The Enable Profile ASF check box selects different amplitude
scale factors by using the different profiles.
The Enable Inverse Sinc check box turns on or off the inverse
sinc filter. This filter compensates for the frequency related
amplitude roll-off caused by the sinc function nature of the
sampling DAC.
The Enable Sine Out check box selects the output as cosine
or sine.
07801-010
The Clear CCI check box clears the CCI filter from an overflow
condition. An overflow condition causes wide band noise at the
output of the device. This condition is usually caused by a CCI
rate change while Tx_ENABLE is high. In addition, the
overflow can be the result of excessive jitter on the external
clock, or the internal PLL is unlocked.
Figure 10. Edit Output Scale Factor Pop-Up Window
Activate
The Activate section in the Profiles window allows you to select
which profile register is active. The active profile register is the
one that supplies the frequency tuning and phase offset words
along with the amplitude control and modulation control (for
QDUC mode) to the DDS core. This section functions the same
way for all modes of the AD9957. This window controls three
external pins, which may also be driven by an external source.
Rev. 0 | Page 13 of 32
EVAL-AD9957
VIEW WINDOWS
QDUC RAM CONTROL
To access the View Windows, click the View tab at the top of
the screen in Figure 3 and select from the pull-down menu.
Click the Enable RAM check box to use the RAM (see
Figure 12). The RAM has two available internal destinations.
See the AD9957 data sheet for a complete description of the
RAM and its entire functionality. The QDUC RAM Destination
box selects which of the two destinations the RAM data is
loaded into.
OSK Control
Set the beginning address, final address, and address step rate in
the forms provided. Use the Mode Control pull-down window
to select the playback mode for the RAM. Use Load RAM and
Save RAM to load or save files to and from the PC for use in the
RAM. The Set ISFC Pin High and Set ISFC Pin Low buttons
are used to control that external pin. When this pin is high, the
RAM sweeps from the beginning RAM address to the end
address. When it is low, the RAM sweeps from the end address
to the beginning address.
07801-011
To use the OSK function of the AD9957, click the Enable
Output Shift Keying box (see Figure 11). Set the Amplitude
Scale Factor to control the final amplitude of the signal. Check
Use External OSK Pin for manual control of the OSK. You can
use the OSK Pin button to manually control the on/off of the
OSK manually. The OSK Pin button controls a pin that can be
driven externally. Check Enable Auto OSK to use the automatic
OSK function. Set the Amplitude Ramp Rate and the Amplitude
Step Adjust using the boxes provided. The Load ARR @ I/O
Update box allows you to reload the ramp rate timer when an
I/O update is issued or when there is a profile change.
07801-012
Figure 11. OSK Control Window
Figure 12. QDUC RAM Control Window
Rev. 0 | Page 14 of 32
EVAL-AD9957
FIFO CONTROL
MULTICHIP SYNC CONTROL
The AD9957 evaluation board comes equipped with a FIFO
that allows you to apply baseband modulation data to the
AD9957 for evaluation purposes. This should be only raw I/Q
data. Note that the FIFO has a speed limit of 100 MHz; consider
this when designing modulation data. The FIFO has a refresh
time when the memory wraps around that last 2048 PDCLK
cycles. The FIFO holds Tx_ENABLE during the refresh time.
This affects use with the FIFO in looping the transmission.
The Multi-Chip Sync window allows you to set up the sync
function (see Figure 14). This allows you to sync multiple chips
to one master AD9957. Refer to the AD9957 data sheet for a full
discussion on multichip sync functions. The Input Sync Pulse
Delay pull-down menu sets the input delay of the synchronization receiver in 150 ps steps. The Output Sync Pulse Delay
pull-down menu sets the output delay of the synchronization
generator in 150 ps steps. The Sync Window Delay pull-down
menu sets the state that the internal clock generator assumes
when it receives a sync pulse. The Sync Enable check box sets
the synchronization clock receiver to active. The Sync Driver
Enable check box sets the synchronization clock generator to
active. The Generate Sync Pulse control area allows you to
select the sync pulse generation corresponding to the rising or
falling SYSCLK edge. The Sync Sample Error section displays
a flag when there is a sync sample error. Use the Clear Error
button to clear a sample error. Refer to the AD9910 data sheet
section for synchronizing multiple parts.
07801-014
In the LOAD FIFO section (see Figure 13), use the three select
buttons, Fill FIFO with Random Data, Load FIFO with
(0-262143), and Load Data from a file:, to select the source of
the data to be loaded into the FIFO. Use the browse button or
the form to enter the location of the file to be used. If using BFI
mode, select the Format Data for BFI Mode check box and be
aware of the LSB First Mode check box under the BFI Mode
Data Format section. Use the LOAD FIFO button to transfer
the data from the PC to the FIFO. A pop-up box alerts you
whether the transfer was successful. Use the Loop Transmission
check box to tell the AD9957 evaluation software to run the
modulation data into the AD9957 continuously. Leaving this
box unchecked only transmits the data for one burst. Use the
Transmit FIFO Data button to initiate the transfer of data to
the AD9957.
07801-013
Figure 14. Multi-Chip Sync Window
Figure 13. FIFO Control Window
Rev. 0 | Page 15 of 32
EVAL-AD9957
GPIO
Configure GPIO Lines
The Input and Output buttons allow you to select whether
an individual pin is configured as an input or an output (see
Figure 15). The Data Pins column lists all 18 of the GPIO pins.
The LOAD and READ buttons allow you to program each pin
or read the value of each pin.
Read/Write Data Lines
07801-016
The Data Line column shows the 18 pins available. The Data
column allows you to set each pin to logic high or logic low.
Figure 16. Debug Window
DUT Signals (PA)
The ISFC, ExtPwrDwn, Reset DUT, I/O Reset, and CSB check
boxes control the pins to which they correspond. All of these
functions are available elsewhere in the software. Clicking these
boxes means that the pin is in its active state. Note that this does
not mean that the pin is logic high or low, which is determined
by the active state on that pin. See the AD9957 data sheet for
information about external pins. The Flash and USB_Status
check boxes are used to control the two LEDs on the AD9957
evaluation board.
DUT Signals (PE)
The I/OUpdateEn, I/O Update, OSK, P3, P2, and P1 boxes
control their selected pins. Pin P3, Pin P2, and Pin P1 control
the profile register pins. See the AD9957 data sheet for the logic
to control the profiles via the external pins.
DUT Signals (CTL)
07801-015
The serial clock (SCLK) pin is used to synchronize data to and
from the AD9957 and to run the internal state machines. This
window allows you to toggle the external pin.
Figure 15. GPIO Window
DEBUG WINDOW
The Debug window gives you complete direct access to the
register map as well as control of many external pins (see
Figure 16). The Debug window is intended for debugging
issues with the AD9957. It may be used for all programming,
but is not user friendly. Note that the Auto Apply check boxes
indicate that when a box is selected, the action is automatically
taken without needing to click Apply.
Rev. 0 | Page 16 of 32
EVAL-AD9957
DUT Flags (PD)
DUT I/O
The CCI Over Flow, PLL Lock, Sync Sample Error, and RAM
Sweep Over flags indicate an active state on each of those
external pins. See the AD9957 data sheet for descriptions of
the active state of each pin.
The DUT I/O window allows you to select the serial I/O port
configuration. Under I/O Port Config, you can select either
2-Wire or 3-Wire mode. In the Data Format mode, you can
select MSB First or LSB First. See the AD9957 data sheet for
more information on these serial port modes. The Reset I/O
Port button allows you to reset the I/O port at any time.
Serial I/O
The Serial I/O section allows direct access to the register map.
The Reg Addr pull-down menu allows you to select the register
of interest. The bit numbers are shown above each byte in the
register. The maximum size of any given register is eight bytes.
For registers that are smaller, the unavailable bytes are grayed
out. You can enter the register values in either binary or hexadecimal code.
The Serial Port Status box displays the serial operating mode of
the AD9957.
REGISTER MAP (SOFTWARE BUFFER) VALUES
WINDOW
07801-018
The Register Map (Software Buffer) Values window allows
you to read the values in the software buffers (see Figure 17).
These values are not sent to the AD9957 from the software
buffers until and I/O update is issued.
Figure 18. DUT I/O Window
The Choose REGMAP Buff drop-down menu allows you to select
between the current or the new values in the software buffer.
The Format selection allows you to choose values to be
displayed in either binary or hexadecimal format.
07801-017
The Auto Refresh check box allows the software to update the
values displayed as they are updated in the buffers. This can be
disabled and you can refresh manually by clicking the Refresh
button.
Figure 17. Register Map (Software Buffer) Values Window
Rev. 0 | Page 17 of 32
EVAL-AD9957
MODULATION VECTOR GENERATOR
The modulation vector generator (MVG) software is built
into the AD9957 software. It allows users to create modulation
schemes and save them as files. The modulation data can be
loaded into the AD9957 using the FIFO. This allows you
inclusive access for creating modulation data for use in the
QDUC mode of the AD9957. To access this software, click
the MVG button located in the toolbar at the top of the
AD9957 software (see Figure 3). The modulation vector
generator is capable of producing modulation data for three
different modulation schemes: QAM, GMSK\EDGE, and
SKPSK (see Figure 19). In addition to providing the
modulation data, the generator produces a graph of the
impulse response and the frequency response of the userdefined symbol pulse shaping filter.
filters on the AD9957. There is no rule for predicting the
amount of attenuation (if any) required for a particular
application, so some trial and error may be necessary. The
Filter Graph Pts box sets the number of plotted points for
the graphs produced by the MVG software.
The QAM tab in the Modulation Vector Generator window
allows you to generate QAM data in different conditions. The
Number Of Symbols field allows you to specify the number
of symbols used in the modulation. The button to the right
side of the entry field sets the field to the maximum number
of symbols that can be used with the 65K FIFO. See the FIFO
Control section for more information. The Number of Output
Vectors field displays the total number of samples that the
generator produces (based on the symbol count and upsampling factor). The Filter Type selection switches between the
different filter types: Raised Cosine and Square Root Raised
Cosine. The Filter Taps field allows you to set the number of
digital filter taps. When setting the number of taps be aware
that setting the taps to an odd or even number may impact the
quality of the demodulated signal depending on the measurement equipment. The receive filter in the equipment used to
demodulate the signal might be even, odd, or selectable. In any
case, the receive and transmit filters must both be of the same
general order (odd or even). If this is different, it can severely
degrade the error vector magnitude (EVM) that can be
measured.
The Filter Tap Resolution field allows you to specify the
resolution (in bits) of the digital filter tap coefficients. An
entry of zero results in floating point coefficients. The Filter
Up-Sampling Factor field sets the amount by which the pulse
shaping filter oversamples the baseband symbols. The Filter
Rolloff Factor (alpha) field is the excess bandwidth parameter
of the pulse shaping filter. See the AN-922 Application Note for
more information on alpha and other modulation information.
The Number of Output Bits field sets the resolution of the final
output data. The AD9957 expects 18-bits of data, so this should
be the value used in most cases. The Attenuation Value field
is used to reduce the full-scale digital amplitude of the final
output data. This is important because in some cases, using the
full-scale amplitude can result in clipping in the half-band
07801-019
QAM
Figure 19. Modulation Vector Generator in QAM Mode
The Output Data Format field sets the format of the final
output data. In all cases, the output file is a standard text file
readable by most text editors. The Interleaved I/Q setting
produces a single output file of signed integers with each integer
on a separate line. The first line is the first I sample, the second
line is the first Q sample, the third line the second I sample, etc.
The AD9957, by default, expects interleaved samples on its parallel
data port, so Interleaved I/Q is the default setting. The I&Q
setting produces separate I and Q data files. The remaining
assortment of I&Q Bits settings are used for generating data
for the Blackfin interface mode of the AD9957. These formats
yield a single bit (0 or 1) per line in the output file. See the
AD9957 data sheet for more information on using Blackfin
interface mode.
The Output Filename box allows you to define the name
and location of the output files generated by the MVG. It is
important to note the location of the output data file(s)
because both the FIFO and the simulator tools require you
to enter the location of the data file(s). The default location
is the QAMVectGen folder where the AD9957 evaluation
board software is installed. Click the Generate Data button
to generate the specified modulation data and to plot the
filter response graphs.
Rev. 0 | Page 18 of 32
EVAL-AD9957
The MVG creates three additional files in the selected directory.
Each file contains the sequence of random symbols generated
by the MVG. The symbols are given in decimal, binary, and
hexadecimal format in the symbol.bin, symbol.dec, and
symbol.hex files, respectively. The binary and hexadecimal
versions of these can contain appended zero bits in the MSB
positions to generate whole nibbles. For example, QPSK data
consists of only two bits, but the symbol.bin file contains whole
nibbles with the two MSBs being 0.
GMSK/EDGE
Number of Truncated Samples = Filter Span × Upsampling Factor
SDPSK
The MVG can also generate data according to SDPSK
modulation.
07801-021
07801-020
The MVG can also generate data conforming to the GSM
standards. Refer to the ETSI standard, GSM 05.04, for more
information on GSM standards. Many of the settings on the
GMSK\EDGE tab are the same as the QAM tab (see Figure 20).
The following settings are different.
The Filter Span (Symbols) field sets the symbol length of the
filter response. To conform to the GSM standard, this number
should be 3 for GMSK and 5 for EDGE data. Changing this to
another value results in nonstandard data. The GMSK Normalized
Bandwidth and GMSK Modulation Index parameters are also
set by the GSM standard. The Enable Full Length Output
check box assures valid data through the filter. This truncates
the first samples in and the last samples out of the filter. Using
those samples results in demodulation errors, as that data is
undefined. This parameter depends on the upsampling factor.
To find the number of samples truncated, use the following
equation:
Figure 20. Modulation Vector Generator in GMSK/EDGE Mode
Figure 21. Modulation Vector Generator in SDPSK Mode
Rev. 0 | Page 19 of 32
EVAL-AD9957
SIMULATOR
properly. The previous sections of this data sheet along with
the AD9957 data sheet provide information on data formatting.
The Run Simulator button applies the software settings and the
modulation data to the simulator. The simulator produces two
different graphs. The first graph shows the time domain response
of the simulated output, a virtual oscilloscope. The second
graph shows the frequency domain response of the simulated
output, a virtual spectrum analyzer.
The Register Map Options section allows you control of where
the simulator settings come from (see Figure 22). The Use the
Current DUT Settings option requires that a AD9957 evaluation board be connected to the PC. The simulator reads the
settings from the DUT and uses them as the device settings.
The Use Current Software Settings option uses the values that
have been entered into the AD9957 evaluation board software.
Set up the software as if using it to program the DUT even if
one is not present. For example, the system clock frequency and
frequency tuning word should be set as normal. The Auxiliary
Control File section is necessary for running the simulator
software. This file sets up parameters specific to the simulator.
The I/Q Base Band Data File is the file that contains the
baseband modulation data. For example, the modulation
vector generator included with the AD9957 evaluation board
software could be used to generate this data file. It can also
come from another source as long as the file is formatted
Rev. 0 | Page 20 of 32
07801-022
The AD9957 evaluation board software has a simulator
built into it. This simulator extracts the device settings of
the AD9957 either from the programming windows of the
evaluation board software or directly from the internal
registers of the device. The simulator uses MATLAB code
to model the AD9957 and produce both a time domain and
frequency domain plot of the simulated AD9957 output signal.
See the Simulator Tool section for more information on the
actual workings of the simulator. The simulator is accessed with
the Simulator button on the toolbar of the AD9957 evaluation
board software (see Figure 3).
Figure 22. AD9957 Simulator Interface Window
EVAL-AD9957
SIMULATOR TOOL
OVERVIEW
The AD9957 evaluation board software includes a MATLABbased simulator tool. The simulator is a virtual model of the
AD9957 that works in unison with the evaluation board software. The device parameters programmed via the evaluation
board GUIs are passed to the simulator. The simulator uses the
programmed parameters to model a virtual AD9957 in the time
domain. The simulation results are displayed in both the time
and frequency domain in two separate plot windows—the
equivalent of a virtual oscilloscope and spectrum analyzer (see
the Virtual Oscilloscope and Spectrum Analyzer section).
When programmed for QDUC mode (either using the parallel
data port or the dual serial port) or for interpolating DAC
mode, the AD9957 is normally driven with time domain data
samples originating from an external source (a microcontroller
or FPGA, for example). The samples are delivered to either the
18-bit parallel data port or the dual serial port (BlackFin interface). For these modes of operation, provide data files that
contain the data streams normally delivered to the device input
(see the User Data File(s) section). The simulator reads these
files and treats them as the time domain input sequence to the
device. The data is processed along the data path of the virtual
device (in the time domain) and the signal at the output of
virtual device is presented in the form of both a time and
frequency domain plot.
One very useful feature of the simulator is that it functions
without the need of a physical AD9957 evaluation board. The
simulator can extract the device programming information
directly from evaluation board GUIs. This allows the simulator
to serve as a virtual development tool during the early stages
of a design. The user can see the results of various baseband
modulation schemes and device settings without the need for
a physical prototype.
SIMULATOR ACTIVATION
The simulator is activated by clicking the Simulator button in
the toolbar of the evaluation board main GUI (see Figure 3).
However, first enter the appropriate device parameters the
various evaluation board GUI windows. The device parameters
can come from one of two sources, either directly from the GUI
windows or via an interrogation of the register contents of the
AD9957 device on the evaluation board (assuming an evaluation board is present). Therefore, when the simulator is
activated the evaluation board software prompts the user for
the desired source of the device parameters.
While the simulator is running, it provides detailed information
of its progress. This information is displayed in a separate
console window with the option of either displaying or hiding
the console window.
At the end of the simulation, two plot windows are displayed.
The first is a time domain plot that serves as a virtual
oscilloscope. The second is a frequency domain plot that
serves as a virtual spectrum analyzer.
SIMULATOR DESCRIPTION
The simulator models the digital behavior of the AD9957.
Although it is not a fully bit true device model, it models the
quantization, truncation, and clipping behavior of the digital
signal processing components (such as, the various digital
filters, the digital modulator, the DDS core) to a high level of
precision.
The simulator is not intended to exactly model the spurious
or noise contributions associated with the analog components
of the AD9957. However, in an attempt to simulate the output
spectrum to a reasonably high degree, two significant distortion
contributors are modeled.
The first modeled distortion contributor is the sin(x)/x
frequency domain distortion that results from the sampled
nature of the DAC output signal. This is modeled by imposing
a sin(x)/x distortion envelope on the final DAC output spectrum. An artifact of this technique, however, is that the sin(x)/x
distortion is imposed on the noise floor. This exhibits itself as a
noticeable droop in the noise floor near the sampling frequency
of the DAC. However, normal device operation restricts the
maximum useable output frequency to be less than ½ the DAC
sampling rate (that is, the Nyquist frequency). With this
restriction the artificial droop imposed on the noise floor is
constrained to less than 4 dB.
The second modeled distortion contributor is the harmonic
distortion of the DAC. Again, this is not intended as an exact
model but offers a reasonable approximation of the typical
spectral performance of the device. The ability to model DAC
harmonic distortion allows you to observe the frequency
location of harmonic spurs.
Rev. 0 | Page 21 of 32
EVAL-AD9957
•
Some analog characteristics are not modeled at all. These
include the spurious clock artifacts associated with the
DAC, noise contributions of the REFCLK PLL signal path,
and effects due to variations in temperature, power supply
voltage, or the semiconductor fabrication process. Additionally,
some ancillary digital features of the AD9957 are not modeled
either. The features and functionality that are not modeled by
the simulator are
•
•
•
Profile activation via the external profile pins (Profile0,
Profile1, Profile2)
Functionality of Profile Register 1 through Profile
Register 7 (however, the simulator does use Profile
Register 0 to extract any profile-specific device parameters)
Multichip synchronization
RAM functionality
DIALOG BOX
•
A functional block diagram of the simulator is shown in
Figure 23. The AD9957 simulator software receives input
from a number of sources. These are the register image file,
the auxiliary control file, and the user data file(s).
EVALUATION BOARD SOFTWARE
SIMULATE
CREATE
REGISTER MAP
IMAGE FILE
AD9957
SIMULATOR
LIBRARY OF
FUNCTIONAL BLOCKS
1) HALF-BAND FILTERS
2) CCI FILTER
3) DDS
4) INVERSE SINC FILTER
5) INVERSE CCI FILTER
6) DAC
7) OSCILLOSCOPE
8) SPECTRUM ANALYZER
9) ETC.
AUXILIARY
CONTROL
FILE
USER
DATA FILE(S)
AD9957 SIMULATOR
MAIN
SINGLETONE
SIMULATOR
QDUC
SIMULATOR
FREQUENCY
DOMAIN
PLOT
BLACKFIN
QDUC
SIMULATOR
INTERPOLATING DAC
SIMULATOR
TIME
DOMAIN
PLOT
Figure 23. Functional Block Diagram of the AD9957 Evaluation Board Software and Simulator Tool
Rev. 0 | Page 22 of 32
07801-023
•
•
•
•
•
•
OSK functionality (except for manual control of amplitude
via the evaluation board GUI)
Functionality of the PDCLK and TxENABLE pins
Functionality of the GPIO port
Power-down functionality
Functionality of the I/O_UPDATE pin
REFCLK PLL functionality (that is, the simulator does not
model phase noise or jitter associated with the REFCLK
signal path)
DAC distortion products (the simulator models the DAC
as being ideal)
EVAL-AD9957
When the Simulator button (see Figure 3) is pressed, the
evaluation board software presents a dialog box that allows the
user to enter (or browse for) the path and file name of the
pertinent file(s). In addition, the user selects whether register
programming information comes directly from the evaluation
board GUI windows or as a result of interrogating the register
contents of the physical device. In either case, the evaluation
board software generates a register image file that contains an
image of the device programming information, which the
simulator uses to determine the appropriate simulation
parameters. The dialog box always asks for the name of the
auxiliary control file and optionally for the file(s) containing the
user’s time domain data (when the AD9957 is programmed for
either the QDUC or interpolating DAC modes).
SINGLE-TONE MODE SIMULATION
After finishing the instructions, the evaluation board software
launches the simulator. The simulator receives two parameters
passed to it directly by the evaluation board software:
Note that the simulator only uses Profile Register 0 to determine any profile-specific device programming parameters.
Profile Register 1 to Profile Register 7 are ignored.
•
When the simulator is activated, the evaluation board software
prompts the user for the name and location of the auxiliary control
file. The simulator reads the auxiliary control file as well as the
register image file. The register image file is generated by the
evaluation board software and provides the simulator with the
frequency tuning word and the phase offset word for the DDS,
the state of the sine enable bit (to model the appropriate DDS
output), the value of the optional amplitude scale factor, whether
or not the inverse sinc filter is bypassed, and the full scale
current setting for the DAC.
The name of the register image file (created by the
evaluation board software)
The frequency of the system clock (that is, the DAC
sample rate)
SIMULATE
SIMULATION DIALOG BOX
The simulator reads the register image file and determines
which of the four available simulation types to execute:
•
•
•
•
AUXILIARY CONTROL FILE NAME
Single tone
Quadrature digital up-converter (QDUC) using the
parallel data port
QDUC using the Blackfin interface (dual serial port)
Interpolating DAC
REGISTER
MAP FILE
SINGLE-TONE
SIMULATOR
AUXILIARY
CONTROL
FILE
In addition to the simulation type, the simulator also extracts
specific device programming information from the register
image file (such as DDS output frequency, DDS phase offset,
QDUC interpolation factor, input data format).
The simulator also reads the contents of the auxiliary control
file. This file defines additional simulation parameters that are
not part of the evaluation board software. For example, control
parameters for the virtual oscilloscope and spectrum analyzer
are stored in the auxiliary control file. This file is intended to
be edited by the user (using a text editor) so that the auxiliary
parameters can be customized. The auxiliary control file is
covered in detail in the Auxiliary Control File section.
Rev. 0 | Page 23 of 32
FREQUENCY
DOMAIN
PLOT
TIME
DOMAIN
PLOT
07801-024
•
A block diagram of the simulator with the AD9957 programmed for single-tone operation is shown in Figure 24.
Figure 24. Simulation Block Diagram for Single-Tone Mode
EVAL-AD9957
QDUC PARALLEL DATA MODE SIMULATION
QDUC BLACKFIN (SERIAL DATA) MODE
SIMULATION
A block diagram of the simulator with the AD9957 programmed for QDUC operation using the parallel data port
is shown in Figure 25.
When the simulator is activated, the evaluation board software
prompts the user for the name and location of the auxiliary
control file and the time domain data file of the user. The time
domain data file contains the baseband I/Q samples that
would otherwise be delivered to the 18-bit parallel data port
of the AD9957 (see the User Data File(s) section for details).
The simulator reads the auxiliary control file as well as the
register image file. The register image file is generated by the
evaluation board software and provides the simulator with
all the device programming information required to simulate
QDUC operation with the parallel data port. The simulator
also reads the time domain data file, which serves as the
baseband input signal to the device.
Note that the simulator only uses Profile Register 0 to determine any profile specific device programming parameters.
Profile Register 1 to Profile Register 7 are ignored.
A block diagram of the simulator with the AD9957 programmed for QDUC operation using the dual serial port
(Blackfin interface) is shown in Figure 26.
When the simulator is activated, the evaluation board software
prompts the user for the name and location of the auxiliary
control file and the time domain data files of the user. The time
domain data files contain the baseband I and Q bit streams
that would otherwise be delivered to the dual serial port of
the AD9957 (see the User Data File(s) section for details).
The simulator reads the auxiliary control file as well as the
register image file. The register image file is generated by the
evaluation board software and provides the simulator with all
the device programming information required to simulate
QDUC operation with the Blackfin interface. The simulator
also reads the time domain data files, which serve as the
baseband input signal to the device.
Note that the simulator only uses Profile Register 0 to determine any profile specific device programming parameters.
Profile Register 1 to Profile Register 7 are ignored.
SIMULATE
SIMULATE
SIMULATION DIALOG BOX
AUXILIARY CONTROL FILE NAME
SIMULATION DIALOG BOX
I/Q DATA FILE NAME
AUXILIARY CONTROL FILE NAME
I BITSTREAM FILE NAME
Q BITSTREAM FILE NAME
REGISTER
MAP FILE
I/Q DATA FILE
REGISTER
MAP FILE
AUXILIARY
CONTROL
FILE
I BITSTREAM
FILE
BLACKFIN
QDUC
SIMULATOR
TIME
DOMAIN
PLOT
Q BITSTREAM
FILE
07801-025
FREQUENCY
DOMAIN
PLOT
AUXILIARY
CONTROL
FILE
FREQUENCY
DOMAIN
PLOT
Figure 25. Simulation Block Diagram for QDUC Mode With the
18-Bit Parallel Data Port
TIME
DOMAIN
PLOT
Figure 26. Simulation Block Diagram for QDUC Mode with the
Dual Serial Port
Rev. 0 | Page 24 of 32
07801-026
QDUC
SIMULATOR
EVAL-AD9957
INTERPOLATING DAC MODE SIMULATION
VIRTUAL OSCILLOSCOPE AND SPECTRUM
ANALYZER
A block diagram of the simulator with the AD9957
programmed for interpolating DAC operation is shown
in Figure 27.
When the simulator is activated, the evaluation board software
prompts the user for the name and location of the auxiliary
control file and the time domain data file of the user. This
data file contains the time domain data samples that would
otherwise be delivered to the 18-bit parallel data port of the
AD9957 (see the User Data File(s) section for details).
The simulator reads the auxiliary control file as well as the
register image file. The register image file is generated by the
evaluation board software and provides the simulator with all
the device programming information required to simulate the
interpolating DAC mode. The simulator also reads the time
domain data file, which serves as the input signal to the device.
Note that the simulator only uses Profile Register 0 to determine any profile specific device programming parameters.
Profile Register 1 to Profile Register 7 are ignored.
SIMULATION DIALOG BOX
AUXILIARY CONTROL FILE NAME
REGISTER
MAP FILE
TIME
DOMAIN
PLOT
Tx DAC
DATA FILE
Note that the default auxiliary control file supplied with the
simulator software uses a 4-term Blackman Harris window.
USER DATA FILE(S)
07801-027
FREQUENCY
DOMAIN
PLOT
The spectrum analyzer plot is the result of an FFT computation
performed by the simulator. Often, it is desirable to apply a
windowing function to the data before computing the FFT.
The auxiliary control file provides the user with the option to
select from a variety of common FFT windowing functions.
Note that the default auxiliary control file supplied with the
simulator software has the minimum and maximum horizontal
and vertical axis limits specified as zero. This causes the simulator to automatically adjust the axis limits according to the
bounds of the data.
Tx DAC DATA FILE NAME
AUXILIARY
CONTROL
FILE
Both plots are MATLAB-based plot windows. Each can be
modified via the controls on the toolbar of the plot window.
For example, the trace can be magnified/compressed by
zooming in/out or individual tags can be placed directly in
the plot window for use as data point markers.
The axis limits for both plots are specified in the auxiliary
control file (see the Auxiliary Control File section for details).
The user can edit the auxiliary control file to customize the
horizontal and vertical limits as desired.
SIMULATE
INTERPOLATING
DAC
SIMULATOR
The virtual oscilloscope and spectrum analyzer are the time
domain and frequency domain plots, respectively, generated
by the simulator. They represent the signal that would appear
at one of the output pins of the AD9957 DAC, including any
optional scaling specified in the auxiliary control file.
Figure 27. Simulation Block Diagram for Interpolating DAC Mode
When simulating the QDUC or interpolating DAC modes you
must provide the simulator with a data file (or a pair of data
files for QDUC operation using the Blackfin interface). The
user data file contains the time domain samples that would
normally be delivered to the 18-bit parallel data port or the
dual serial port (Blackfin interface) of the AD9957 using
external hardware (a microcontroller or FPGA, for example).
A user data file is a simple text file (for example, a file created
with Notepad, the basic text editor that is supplied with the
Windows® operating system). Each line in the text file contains
an integer that represents an input sample to the AD9957. Each
integer must be in the range of −131072 to +131071 (inclusive)
when the parallel data port is the intended input or either 0 or 1
when the dual serial port (that is, the Blackfin interface) is the
intended input.
Rev. 0 | Page 25 of 32
EVAL-AD9957
When simulating QDUC operation with the 18-bit parallel data
port, the data file must contain an even number of samples. The
reason is that the simulator expects the data to represent alternating I/Q sample pairs, the same way that data is delivered to
the 18-bit parallel port in QDUC mode. The first line in the file
contains the first I-sample, the second line the first Q-sample,
the third line the second I-sample, the fourth line the second
Q-sample, etc.
When simulating the interpolating DAC mode an arbitrary
number of samples can be used. That is, the even number
of samples restriction associated with the QDUC mode does
not apply.
When simulating QDUC operation with the Blackfin interface
two data files are required. One contains the I bit stream and
the other the Q bit stream. Each data file must contain a
number of samples that is divisible by 16. The reason is that
the simulator expects the data files to represent the serial bit
streams that would normally be delivered to the dual serial port.
That is, each bit stream must be partitioned into 16-bit frames
with each frame defining a 16-bit signed integer. In accordance
with the functionality of the AD9957, the 16-bit frames can be
formatted as containing either twos-complement or offset
binary numbers and can be presented in either LSB-first or
MSB-first order. Of course, the device programming via the
AD9957 evaluation board software must match the data file
format; otherwise the simulator does not properly translate
the data file contents.
AUXILIARY CONTROL FILE
The auxiliary control file contains 23 parameters that the user
can alter to customize a simulation run. It is a simple text file
in which instructions are organized as pairs of consecutive
lines. The first line in a pair contains a keyword that identifies
a particular parameter and the next line contains the value
associated with the keyword. The simulator reads the auxiliary
control file one line at a time. When it encounters a keyword it
uses the next line as the value for the parameter associated with
the keyword.
Note that the simulator searches for keywords as an exact
match so they are case sensitive. The keywords must also be
left justified (that is, the first character of the keyword must
not be preceded by any other character).
The auxiliary file can also contain comment lines. These are
either blank lines or lines that begin with a percent (%) symbol.
Comment lines are ignored by the simulator.
Note that a remark line must not appear between a keyword
and its associated value.
The parameter value associated with a keyword is either a
numeric quantity or a character string (depending on the
particular parameter that is associated with the keyword).
Numeric parameter values may be entered in any of the
numeric formats supported by MATLAB. For example,
2400 may be entered as 2400, 2.4E3, 2.4e3, 2.4D3, or 2.4d3.
Character string parameter values must begin and end with
a single-quote character (‘).
Rev. 0 | Page 26 of 32
EVAL-AD9957
KEYWORDS
A comprehensive keyword list is listed in this section. It
includes an explanation of the function of the keyword
parameter and any restrictions on its parameter value.
RSET
DEBUG
•
•
•
•
•
•
•
Enables or disables the debug mode of the simulator.
Parameter value must be numeric.
Zero disables the debug mode of the simulator; any
nonzero value enables it.
In debug mode, the simulator prints additional detailed
information to the console window during the simulation
process. It also generates time and frequency domain plots
for each significant node along the signal path.
DACXFR
•
•
•
SHOWCLIP
•
•
•
Controls the display of clipping events.
Parameter value must be numeric.
Some of the signal processing blocks in the AD9957 signal
path (the half-band filters are one example) apply clipping
to samples that would otherwise cause a numeric overflow
or underflow. When the simulator detects that clipping
has occurred at a particular node it displays information
regarding each clipped sample. The showclip value tells
the simulator the maximum number of clipped samples
for which to print detailed information. For example, if
the showclip is 10, then every functional block that clips
during simulation is limited to displaying no more that
10 clipped samples.
SAMPLES
•
•
Defines the number of samples that the simulator generates
for single-tone mode.
Parameter value must be numeric and must be a positive
integer.
DDSCORE
•
•
•
The value of the DAC RSET resistor (in ohms) installed on
the evaluation board (the default value is 10,000).
Parameter value must be numeric and greater than zero.
The RSET resistor establishes the full-scale output current of
the DAC.
Defines how the simulator models the harmonic distortion
of the DAC.
Parameter must be numeric.
A zero value tells the simulator to model the DAC with a
perfectly linear transfer function (that is, no harmonic
distortion). A nonzero value tells the simulator to use a
distorted transfer function that produces typical harmonic
products.
FFTWINDOWTYPE
•
•
•
Specifies the windowing function applied to the data prior
to computing an FFT.
Parameter must be a character string.
The parameter value is a four-character mnemonic that
identifies a particular window function as shown in
Table 4.
Table 4.
Mnemonic
rect
bart
hamm
hann
blk3
blk4
rose
Defines how the simulator treats the angle-to-amplitude
conversion of the DDS core.
Parameter must be numeric.
A zero value tells the simulator to calculate an ideal,
14-bit quantized lookup table to emulate the DDS core.
A nonzero value tells the simulator to load the DDS core
values that were extracted from the digital code used to
produce the actual silicon device.
Note that sometimes a shorter simulation time can be realized
with a value of zero for this parameter because it usually takes
less time to compute a lookup table than to load the relatively
large DDS core files.
Rev. 0 | Page 27 of 32
Description
Rectangular window (that is, no window is applied
to the data)
Bartlett (triangular) window
Hamming window
Hann window
3-term Blackman-Harris window
4-term Blackman-Harris window
Rosenfeld window
EVAL-AD9957
VIRTUAL OSCILLOPE AND SPECTRUM ANALYZER
INSTRUMENTS KEYWORDS
The following ten keywords pertain to the virtual oscilloscope
and spectrum analyzer instruments. The first two parameters
specify the virtual input impedance of the instrument. The next
eight parameters specify the axis limits of the instruments.
Note that when the minimum and maximum limits for a
particular instrument axis are both zero, the simulator
automatically selects the limits for that axis to accommodate
the range of the data.
minV_SCOPE
•
•
Lower limit of the oscilloscope vertical axis.
Parameter value must be numeric.
maxV_SCOPE
•
•
Upper limit of the oscilloscope vertical axis.
Parameter value must be numeric.
minH_SA
•
Lower limit of the spectrum analyzer horizontal
(frequency) axis.
Parameter value must be numeric.
ZSCOPE
•
•
maxH_SA
•
Input impedance (ohms) of the virtual oscilloscope
instrument.
Parameter value must be numeric and nonnegative.
•
•
ZSA
•
•
Input impedance (ohms) of the virtual spectrum analyzer
instrument.
Parameter value must be numeric and nonnegative.
minH_SCOPE
•
•
Lower limit of the oscilloscope horizontal (time) axis.
Parameter value must be numeric.
minV_SA
•
•
Lower limit of the spectrum analyzer vertical axis.
Parameter value must be numeric.
maxV_SA
•
•
maxH_SCOPE
•
•
Upper limit of the spectrum analyzer horizontal
(frequency) axis.
Parameter value must be numeric.
Upper limit of the oscilloscope horizontal (time) axis.
Parameter value must be numeric.
Rev. 0 | Page 28 of 32
Upper limit of the spectrum analyzer vertical axis.
Parameter value must be numeric.
EVAL-AD9957
DAC OUTPUT SIGNAL KEYWORDS
DAC_LOAD_THEV_SCOPE
The remaining six keywords specify the scaling of the DAC
output signal. These parameters are useful for including
external DAC termination circuitry as part of the simulation.
These parameters, however, only allow scaling of the output
amplitude. Frequency dependent behavior associated with the
components of the external DAC termination circuitry cannot
be modeled.
•
The three keywords with the SCOPE suffix control the scaling
of the DAC output signal for the virtual oscilloscope, while the
three keywords with the SA suffix are for the spectrum analyzer.
DAC_LOAD_SCOPE
•
•
The single-ended equivalent load (ohms) at the DAC
output, which includes the combined loading effects of
the external circuitry as well as the input impedance of the
virtual oscilloscope.
Parameter value must be numeric and nonnegative.
•
DAC_LOAD_SA
•
•
•
The gain of an ideal amplifier used to model gain or
loss (active or passive) in the external DAC termination
circuitry in the signal path leading to the virtual
oscilloscope.
Parameter value must be numeric and nonnegative. The
units are assumed to be linear (not decibels).
The single-ended equivalent load (ohms) at the DAC
output, which includes the combined loading effects of
the external circuitry as well as the input impedance of
the virtual spectrum analyzer.
Parameter value must be numeric and nonnegative.
DAC_LOAD_SCALE_SA
•
•
DAC_LOAD_SCALE_SCOPE
•
The Thevenin equivalent load (ohms) of the DAC
termination circuitry as seen from the input of the
virtual oscilloscope looking toward the DAC.
Parameter value must be numeric and nonnegative.
The gain of an ideal amplifier used to model gain or loss
(active or passive) in the external DAC termination circuitry
in the signal path leading to the virtual spectrum analyzer.
Parameter value must be numeric and nonnegative. The
units are assumed to be linear (not decibels).
DAC_LOAD_THEV_SA
•
•
Rev. 0 | Page 29 of 32
The Thevenin equivalent load (ohms) of the DAC
termination circuitry as seen from the input of the
virtual spectrum analyzer looking toward the DAC.
Parameter value must be numeric and nonnegative.
EVAL-AD9957
AD9957 SIMULATOR
SCALING COMPONENTS FOR
THE VIRTUAL OSCILLOSCOPE
SIGNAL PATH.
AD9957
VIRTUAL
OSCILLOSCOPE
DAC_LOAD_SCALE_SCOPE
DAC
DAC_LOAD_THEV_SCOPE
ZSCOPE
DAC_LOAD_SCOPE
SCALING COMPONENTS FOR
THE VIRTUAL SPECTRUM
ANALYZER SIGNAL PATH.
AD9957
VIRTUAL
SPECTRUM
ANALYZER
DAC_LOAD_SCALE_S A
DAC
DAC_LOAD_THEV_SA
ZSA
07801-028
DAC_LOAD_SA
MEASUREMENT
INSTRUMENT
1:1
IOUT
50Ω
DAC
25Ω
IOUT
DAC_LOAD_SCALE
DAC
8
VIRTUAL
INSTRUMENT
50Ω
DAC_LOAD_THEV
DAC_LOAD
Figure 29. Example Schematic of the External DAC Termination Circuitry
Rev. 0 | Page 30 of 32
07801-029
AD9957
50Ω
Figure 29 shows the required scaling component values for the
case in which the DAC drives a center-tapped transformer with
a 1:1 turns ratio. It includes a schematic of the external DAC
termination circuitry and the resulting model of the scaling
components. The scaling component values assume that the
input impedance of the virtual instruments is 50 Ω.
AD9957
6.25Ω
Although the AD9957 has two DAC output pins (normal and
complementary), the simulator models the output as singleended. That is, the simulator treats the DAC as though only
one of the two outputs is used as a signal source. This knowledge
is necessary to properly calculate the parameter values for the
output scaling keywords. This is especially true when using the
simulator to accurately model an external DAC termination
circuit that uses both output pins. Figure 28 shows a diagram
of the scaling components in the context of the simulator’s
treatment of the DAC output and the virtual instruments.
25Ω
Figure 28. Scaling Component Detail
EVAL-AD9957
See the AN-912 Application Note regarding the use of a centertapped transformer with a balanced current-output DAC for
more information.
Z NORM = ZCOMP =
RO RL
2RL + 4 RO N 2
ZS = 2N RO
2
(2)
⎛ 2 I MAX
v NORM = vCOMP = ⎜⎜
8
⎝
⎛ 2 I MAX
vS = ⎜⎜
2
⎝
(1)
⎞
⎞⎛
RO RL
⎟
⎟⎜
⎟⎜ R + 2R N 2 ⎟
O
⎠⎝ L
⎠
⎞⎛ NRO RL ⎞
⎟
⎟⎜
⎟⎜ R + 2R N 2 ⎟
O
⎠⎝ L
⎠
(3)
Equation 1 to Equation 4 are related to the scaling component
values as follows:
ZNORM provides the value for the DAC_LOAD_SCOPE and
DAC_LOAD_SA keywords.
The formula, 2(vS/vNORM), provides the value for the
DAC_LOAD_SCALE_SCOPE and DAC_LOAD_SCALE_SA
keywords.
ZS provides the value for the DAC_LOAD_THEV_SCOPE and
DAC_LOAD_THEV_SA keywords.
(4)
Rev. 0 | Page 31 of 32
EVAL-AD9957
ORDERING INFORMATION
ESD CAUTION
ORDERING GUIDE
Model
AD9957/PCBZ1
1
Description
Evaluation Board
Z = RoHS Compliant Part.
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
EB07801-0-7/09(0)
Rev. 0 | Page 32 of 32
工商网监
湘ICP备2023018690号
