ADA4530-1R-EBZ User Guide
UG-865
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for the ADA4530-1 8-Lead SOIC Package
FEATURES
EVALUATION BOARD PHOTOGRAPHS
Footprint for ADA4530-1 8-lead SOIC package
Footprints for passive components
Available in buffer or transimpedance configuration
Easy modifications to other standard configurations
Guard ring to minimize leakage current
Assembled with metal shields
Enables quick prototyping
Easy connection to test equipment
The ADA4530-1R-EBZ is an evaluation board for the ADA4530-1
offered in an 8-lead SOIC package. The ADA4530-1R-EBZ is a
4-layer printed circuit board (PCB) designed to minimize
leakage currents with its guard ring features for femtoampere
input bias current (IB) measurement.
13409-001
GENERAL DESCRIPTION
Figure 1. ADA4530-1R-EBZ Top View
The ADA4530-1R-EBZ is available in two default configurations:
buffer (ADA4530-1R-EBZ-BUF) and transimpedance
(ADA4530-1R-EBZ-TIA). Both boards are populated with the
necessary passive components, banana jacks/terminal blocks for
supply voltages, BNC/terminal blocks for the output voltage,
multiple test pins, and metal shields. All components are placed
on the primary side with the exception of the triaxial (triax)/
coaxial (coax) input connector (J1) and SHIELD3.
Specifications for the ADA4530-1 are provided in the
ADA4530-1 data sheet available from Analog Devices, Inc.
The ADA4530-1 data sheet and the AN-1373 Application Note
should be consulted in conjunction with this user guide when
using the evaluation board.
Figure 1 shows the top view of the evaluation board, and Figure 2
shows the bottom view. For more views of the evaluation board
images, see the ADA4530-1R-EBZ Evaluation Board Photographs
section.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 14
13409-003
The ADA4530-1R-EBZ also has unpopulated resistor and
capacitor pads that allows quick prototyping with different
configurations, such as noninverting gain and inverting gain.
Figure 2. ADA4530-1R-EBZ Bottom View
UG-865
ADA4530-1R-EBZ User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Buffer with Triax Guard Driven by Amp Guard .......................6
General Description ......................................................................... 1
Buffer with Resistor at IN+ to Ground.......................................7
Evaluation Board Photographs ....................................................... 1
Noninverting Gain ........................................................................7
Revision History ............................................................................... 2
Hardware Components .................................................................... 3
Transimpedance with 10 GΩ SMT Feedback Resistor and
IN+ Connected to Ground (ADA4530-1R-EBZ-TIA) .............8
Board Assembly ............................................................................ 3
Transimpedance with Through Hole Feedback Resistor .........8
Input, Output, and Supplies ........................................................ 3
Transimpedance with Direct Sensor Connection .....................9
Guard and Shield .......................................................................... 3
Inverting Gain ................................................................................9
Board Layers Stackup ................................................................... 4
ADA4530-1R-EBZ Evaluation Board Photographs ................... 10
Cleaning and Handling .................................................................... 5
Evaluation Board Schematics........................................................ 11
Amplifier Configurations ................................................................ 6
Ordering Information .................................................................... 13
Buffer with Triax Guard Externally Driven
(ADA4530-1R-EBZ-BUF) ........................................................... 6
Bill of Materials ........................................................................... 13
REVISION HISTORY
10/15—Revision 0: Initial Version
Rev. 0 | Page 2 of 14
ADA4530-1R-EBZ User Guide
UG-865
HARDWARE COMPONENTS
BOARD ASSEMBLY
Power supplies to the board can be applied in two different ways:
The ADA4530-1R-EBZ evaluation board is available in two
default configurations:
1.
2.
V+_TP, GND_TP, and V−_TP test points are provided.
ADA4530-1R-EBZ-BUF: amplifier is populated in buffer
configuration
ADA4530-1R-EBZ-TIA: amplifier is populated in
transimpedance configuration
Both evaluation boards are pre-assembled with necessary
components, except for SHIELD2. SHIELD2 is included in the
kit, but not installed.
See the Amplifier Configurations section for all other possible
configurations.
INPUT, OUTPUT, AND SUPPLIES
ADA4530-1R-EBZ-TIA is populated with an input BNC
connector (J1) that connects to the amplifier inverting pin
through JP2.
ADA4530-1R-EBZ-BUF is populated with an input triax
connector (J1). The inner conductor of J1 is the high impedance
connection through JP1 to the noninverting pin of the
ADA4530-1. The inner braided shield is a guard; the driving
source is configured with JP3. The outer braided shield is the
signal return; it is connected to GND.
The evaluation board uses JP3 to select the driving source of the
triax guard. Table 1 shows the three different configurations of
JP3.
Table 1. JP3 Configuration
JP3
Unconnected
Short
TRIAX GUARD
to AMP GUARD
Short
TRIAX GUARD
to GND
Description
Triax guard is externally driven. This
configuration is used when the guard is driven
by an external test equipment, such as a
picoammeter. This configuration is also by
default on both the ADA4530-1R-EBZ-TIA and
ADA4530-1R-EBZ-BUF boards.
Triax guard is driven by the ADA4530-1 guard
buffer. This configuration is useful if the
ADA4530-1R-EBZ-BUF is connected to a
passive sensor.
Triax guard is connected to signal ground. This
configuration is useful when the amplifier is in
transimpedance configuration with the
noninverting pin connected to signal ground.
V+ (J3), GND (J4), and V− (J5) allow banana plugs to be used
Terminal block (J6) allows wire-to-board connection
GUARD AND SHIELD
The ADA4530-1R-EBZ board uses guard rings, a guard plane,
and a via fence to entirely guard the high impedance input
traces against leakage current. On the top layer, the guard ring
encircle the inverting and noninverting input components (see
Figure 3). Guard via fences from the top layer to bottom layer
are also used to encircle the high impedance inputs to prevent
leakage currents from inner layers of the board. For more
information on the physical implementation of guarding
techniques, see the ADA4530-1 data sheet.
The copper shield traces, SHIELD1, SHIELD2, and SHIELD3
allow soldered metal shields to enclose the high impedance inputs
as a means to avoid electrostatic interference. The shield traces
are electrically connected to the amplifier guard potential.
SHIELD1 and SHIELD3 are 1 inch × 1.5 inch × 0.25 inch metal
shields and are pre-assembled on board. There is a high
impedance pin socket (P7) that goes through the bottom of the
board, and hence SHIELD3 is populated at the bottom of the
board. Other than providing electrostatic shielding, the shields
also prevent contamination from fingerprints, dust, and other
contaminants to the high impedance inputs.
SHIELD2 is a 1.5 inch × 3 inch × 0.75 inch metal shield and is
provided separately with the evaluation board. It is used when
large through hole resistors are populated on board. RF clips
are assembled to hold the shield in place. Note that it is
sufficient to remove the SHIELD1 cover, without needing to
desolder SHIELD1, to accommodate SHIELD2 when large
through hole resistors are used.
1.
2.
BNC connector (J2) allows BNC cabling
Terminal block (J7) allows wire-to-board connection
GUARD RING
A VOUT_TP test point is also provided.
GUARD VIA FENCE
Figure 3. Guarding
RO isolates the output load from the amplifier output to prevent
any oscillation from excessive capacitive loading. A 499 Ω
resistor is mounted on-board.
Rev. 0 | Page 3 of 14
13409-004
The evaluation board output can be measured with two
different options:
UG-865
ADA4530-1R-EBZ User Guide
13409-005
BOARD LAYERS STACKUP
The ADA4530-1R-EBZ is a 4-layer evaluation board that uses
the Rogers 4350B, a high performance PCB laminate. A hybrid
stackup is required for mechanical strength. The top and bottom
layers are ceramic (Rogers 4350B) while the middle core layer is
a conventional glass epoxy laminate (FR-4). The Rogers 4350B
material provides superior insulation resistance in the presence
of humidity compared to glass/epoxy materials. It minimizes
current leakage and, therefore, increases signal integrity.
Additionally, the dielectric relaxation times of Rogers 4350B are
much shorter than glass/epoxy dielectrics. For more information
on dielectric relaxation, see the ADA4530-1 data sheet.
Figure 4. Board Layer Stackup
Rev. 0 | Page 4 of 14
ADA4530-1R-EBZ User Guide
UG-865
CLEANING AND HANDLING
3.
It is important to always handle the board by the edges and
never touch the area within SHIELD1.
Before using the board, properly clean the evaluation board to
remove any contaminants, such as solder flux, saline moisture,
dirt, and dust, to maintain its low leakage performance. Any
contaminants can severely degrade its femtoampere performance.
The board must also be cleaned again after any rework to the
components.
An effective cleaning procedure consists of the following steps:
1.
2.
Soak the board in an ultrasonic bath with cleanroom grade
isopropyl alcohol for 15 minutes. Ultrasonic cleaning uses
ultrasound at a high frequency, creating cavitation in the
cleaning solution. This process helps to remove contaminants on the surface of the board and in areas under
soldered components that are hard to reach. The next
cleaning steps require using fresh isopropyl alcohol.
Remove the board from the ultrasonic bath with a pair of
forceps. Rinse and flush the board with isopropyl alcohol
to remove any contaminant residue.
4.
5.
6.
7.
8.
9.
Rev. 0 | Page 5 of 14
Flood the board with isopropyl alcohol and gently scrub
it with an acid brush. Concentrate on areas between the
U1 pins, the input traces to J1, the guard ring, and the area
within SHIELD1.
Rinse and flush the board with isopropyl alcohol.
Repeat Step 3 and Step 4 for the bottom of the board.
Give a final flush for the top and bottom of the board with
isopropyl alcohol.
Use compressed dry air to dry the board. Blow air around
the U1 pins, the input traces to J1, and the guard ring area.
Be sure to direct the compressed air under J1 and U1 as well.
To make sure that the board is completely dry, bake the
board in the oven at 125°C for 15 minutes.
After cleaning, remember to place the cover of the metal
shield on both sides of the board. The metal shields help
prevent any contact to the guarded area.
UG-865
ADA4530-1R-EBZ User Guide
AMPLIFIER CONFIGURATIONS
This section describes the different configurations possible with
the evaluation board. For some configurations, remove stated preassembled components to allow assembly of new components of
choice. After any rework, the evaluation board must be cleaned
according to the Cleaning and Handling section.
BUFFER WITH TRIAX GUARD EXTERNALLY
DRIVEN (ADA4530-1R-EBZ-BUF)
BUFFER WITH TRIAX GUARD DRIVEN BY AMP
GUARD
For a buffer configuration where the triax guard is not driven by
any external test equipment, TRIAX GUARD must be shorted to
AMP GUARD via JP3. This configuration is useful when the
buffer is connected to a passive sensor (or an input signal).
Table 3 shows the recommended component values.
The amplifier on this evaluation board is defaulted to a buffer
configuration. An input signal can be applied through the triax
connector, J1. Note that JP3 is left unconnected by default so
that the triax guard can to be driven by external test equipment.
For direct input bias current (IB) measurement, connect an
electrometer such as the Keithley 6430 to the board via J1. The
Keithley 6430 internal guard buffer drives the triax guard (see
Figure 5 and Figure 6 for the configuration). Details regarding
IB measurement are described in the AN-1373 Application Note.
Table 3. Buffer with Triax Guard Driven by Amp Guard
Pad/Connector Configuration1
Pad/Connector
JP1
JP3
RF1
1
Use the ADA4530-1R-EBZ-BUF board.
SHORT TRIAX GUARD
TO AMP GUARD
Table 2. Buffer with Triax Guard Externally Driven
Pad/Connector Configuration
Pad/Connector
JP1
JP3
RF1
Description
0Ω
Short TRIAX GUARD to AMP GUARD
0Ω
Description
0Ω
Unconnected
0Ω
RF1
0Ω
JP1
0Ω
13409-014
RF1
0Ω
JP1
0Ω
Figure 7. Buffer with Triax Guard Driven by Amp Guard
RF1
0Ω
Figure 5. Buffer with Triax Guard Externally Driven
RF1
0Ω
V+
JP1
0Ω
TRIAX
GUARD IS
EXTERNALLY
DRIVEN
U1
V–
JP1
0Ω
TRIAX
GUARD IS
CONNECTED TO
AMP GUARD
U1
V–
RO
499Ω
VOUT
J2
(BNC)
OUTPUT
Figure 8. Buffer with Triax Guard Driven by Amp Guard Schematic
RO
499Ω
J2
(BNC)
OUTPUT
VOUT
13409-007
J1
(TRIAX)
INPUT
V+
13409-015
13409-006
J1
(TRIAX)
INPUT
Figure 6. Buffer with Triax Guard Externally Driven Schematic
Rev. 0 | Page 6 of 14
ADA4530-1R-EBZ User Guide
UG-865
BUFFER WITH RESISTOR AT IN+ TO GROUND
NONINVERTING GAIN
To configure the DUT as a buffer with a large resistor at the
noninverting pin to ground, use the ADA4530-1R-EBZ-BUF
evaluation board and remove JP1. Large value, through hole
resistors (RS2) can be placed between the noninverting pin and
ground using the P7 and P4 pin sockets. Place one end of the
leaded resistor at P7 and the other end at P4 (GND). If an SMT
resistor is used, use the RS1 pad instead. The RS1 pad allows the
assembly of a 1206 or 1210 package size resistor. This configuration allows the user to measure IB+, where VOUT = IB+ × RS1 or
VOUT = IB+ × RS2.
To configure the ADA4530-1 in a noninverting gain, use the
components shown in Table 5. Choose appropriate RF1 and
RS3 values for the desired gain. Note that the pre-assembled
RF1 must be replaced with a resistor of choice.
Table 4. Buffer with Resistor at IN+ to Ground Pad
Configuration1
Pad/Connector
JP1
JP3
RF1
RS3
1
Description
0Ω
Short TRIAX GUARD to AMP GUARD
Replace 0 Ω resistor with resistor of choice
Populate with resistor of choice
Use the ADA4530-1R-EBZ-BUF board.
Description
0Ω
Unconnected
0Ω
Used for a SMT source resistor
Used for a through hole source resistor
SHORT TRIAX GUARD
TO AMP GUARD
RS3
RF1
1
Use the ADA4530-1R-EBZ-BUF board.
2
Assemble either RS1 or RS2..
JP1
0Ω
RS2
(THROUGH HOLE)
13409-016
RF1
0Ω
Figure 11. Noninverting Gain
RS1
(SMT)
RF1
J1
(TRIAX)
INPUT
RS3
V+
13409-012
U1
Figure 9. Buffer with Resistor at IN+ to Ground
RF1
0Ω
TRIAX
GUARD
RS2
(THROUGH HOLE)
J2
(BNC)
RO OUTPUT
499Ω
V+
JP1
0Ω
U1
VOUT
V–
RS1
(SMT)
13409-013
J1
(TRIAX)
INPUT
Figure 10. Buffer with Resistor at IN+ to Ground Schematic
Rev. 0 | Page 7 of 14
JP1
TRIAX
GUARD IS 0Ω
CONNECTED
TO AMP GUARD
RO
499Ω
J2
(BNC)
OUTPUT
VOUT
V–
Figure 12. Noninverting Gain Schematic
13409-017
Pad
JP1
JP3
RF1
RS12
RS22
Table 5. Noninverting Gain Pad/Connector Configuration1
UG-865
ADA4530-1R-EBZ User Guide
TRANSIMPEDANCE WITH 10 GΩ SMT FEEDBACK
RESISTOR AND IN+ CONNECTED TO GROUND
(ADA4530-1R-EBZ-TIA)
TRANSIMPEDANCE WITH THROUGH HOLE
FEEDBACK RESISTOR
On the ADA4530-1R-EBZ-TIA board, the amplifier is defaulted
to a transimpedance configuration. The transimpedance
configuration is a current-to-voltage (I to V) converter. A
10 GΩ SMT 1206 package size feedback resistor (RF1) is preassembled on board. If other resistor values or package sizes are
needed, the 10 GΩ feedback resistor can be desoldered to allow
the assembly for the SMT resistor of choice. The evaluation
board provides a combination footprint that allows assembly of
either an 0805, 1206, 1210, 2510, or 2512 package size for RF1.
Larger value through hole feedback resistors, in the order of high
gigaohms or teraohms, are also often used in a transimpedance
application. This option is discussed in the Transimpedance
with Through Hole Feedback Resistor section.
Table 6. Transimpedance with 10 GΩ SMT Feedback
Resistor and IN+ Connected to Ground Pad/Connector
Configuration
Pad/Connector
JP2
JP3
RF1
RS1
In a transimpedance configuration, larger value through hole
feedback resistors, in the order of high gigaohms or teraohms,
are often used. These resistors are glass encapsulated and
hermetically sealed, and come in large footprints. An example
of this is the Ohmite RX-1M ultrahigh resistance, high stability,
hermetically sealed resistor.
To cater to its large footprint, pin sockets (P7 and VOUT) are
provided for RF2. Place one end of the leaded resistor at P7 and
the other end at VOUT. Note that when using the evaluation
board for this configuration, use the ADA4530-1R-EBZ-TIA
board and remove the pre-assembled 10 GΩ feedback resistor.
When RF2 is used, remove the cover of SHIELD1 to allow
placement of the large through hole resistor. Secure SHIELD3,
which is provided with the kit, with the pre-assembled RF clips
to provide electrostatic shielding.
Table 7. Transimpedance with Through Hole Feedback
Resistor Pad/Connector Configuration1
Description
0Ω
Unconnected
10 GΩ
0Ω
Pad/Connector
JP2
JP3
RS1
RF1
RF2
1
Description
0Ω
Unconnected
0Ω
Remove from board
Populate with resistor of choice
Use the ADA4530-1R-EBZ-TIA board.
JP2
0Ω
RF1
10GΩ
JP2
0Ω
RS1
0Ω
RF2
GΩ/TΩ
13409-008
RS1
0Ω
RF1
10GΩ
V+
U1
RS1
0Ω
V–
RO
499Ω
Figure 15. Transimpedance with Through Hole Feedback Resistor
J2
(BNC)
OUTPUT
J1
(BNC)
INPUT
VOUT
RF2
THROUGH HOLE
JP2
0Ω
V+
U1
RS1
0Ω
Figure 14. Transimpedance with 10 GΩ Feedback and IN+
Connected to Ground Schematic
V–
RO
499Ω
J2
(BNC)
OUTPUT
VOUT
13409-011
JP2
0Ω
13409-009
J1
(BNC)
INPUT
13409-010
Figure 13. Transimpedance with 10 GΩ Feedback and IN+
Connected to Ground
Figure 16. Transimpedance with Through Hole Feedback Resistor Schematic
Rev. 0 | Page 8 of 14
ADA4530-1R-EBZ User Guide
UG-865
TRANSIMPEDANCE WITH DIRECT SENSOR
CONNECTION
INVERTING GAIN
The ADA4530-1R-EBZ-TIA board can be reconfigured to allow
direct sensor connection. The P6 and P1, P2, or P3 pins are
provided to allow assembly of a photodiode. To reconfigure the
board, remove the input BNC connector (J1). The user must then
access Pin P6 (the inner conductor pin of the BNC connector).
Assemble the photodiode of choice between P6 and P1, P2, or P3.
P1, P2, and P3 are electrically connected to signal ground.
These three pins are provided to allow different photodiode
packages to be used, for example: TO-19, TO-5, or TO-8.
To configure the ADA4530-1 in an inverting gain, use the
components shown in Table 9. Choose appropriate RF1 and JP2
values for the desired gain.
Table 9. Inverting Gain Pad Configuration1
Pad
JP2
RS1
RF1
1
Description
Populate with resistor of choice
0Ω
Replace 10 GΩ with resistor of choice
Use the ADA4530-1R-EBZ-TIA board.
Table 8. Transimpedance with Direct Sensor Connection
Pad/Connector Configuration1
RF23
Description
Feedback capacitor2
Remove J1
0Ω
Unconnected
0Ω
Use pre-assembled 10 GΩ resistor or
replace with SMT resistor of choice
Used with through hole feedback resistor
JP2
RF1
RS1
0Ω
13409-018
Pad/Connector
CF1
J1
JP2
JP3
RS1
RF13
1
Use the ADA4530-1R-EBZ-TIA board.
See the Photodiode Interface section in the ADA4530-1 data sheet on how
to select CF1
3
Assemble either RF1 or RF2.
2
Figure 19. Inverting Gain
RF1
JP2
V+
U1
JP2
RS1
0Ω
CF1
PHOTODIODE
RO
499Ω
J2
(BNC)
OUTPUT
VOUT
V–
RF2
Figure 20. Inverting Gain Schematic
13409-124
RS1
0Ω
Figure 17. Transimpedance with Direct Sensor Connection
CF1
RF1 (SMT)
RF2 (THROUGH HOLE)
J2
(BNC)
RO OUTPUT
499Ω
V+
PHOTODIODE
U1
RS1
0Ω
V–
VOUT
13409-125
JP2
0Ω
Figure 18. Transimpedance with Direct Sensor Connection Schematic
Rev. 0 | Page 9 of 14
13409-019
J1
(BNC)
INPUT
UG-865
ADA4530-1R-EBZ User Guide
13409-002
ADA4530-1R-EBZ EVALUATION BOARD PHOTOGRAPHS
13409-121
Figure 21. Evaluation Board Top View with SHIELD1
13409-122
Figure 22. Evaluation Board Bottom View with SHIELD3
Figure 23. Evaluation Board Top View with SHIELD2
Rev. 0 | Page 10 of 14
ADA4530-1R-EBZ User Guide
UG-865
EVALUATION BOARD SCHEMATICS
1
RF2
DNI
GND_P4_TP
1
2
3
AGND
RS3
DNI
CF1
DNI
RF1
VOUT_TP
1 VOUT
10GΩ
R0
VOUT_ISO 1
499Ω
5 4 3 2
GUARD
JP2
1
J2
1-1337445-0
2
IN–
VDD_DUT
0
R1206
1
2
U1
ADA4530-1
1
2
3
JP3
SAMTECTSW10608GS3PIN
AGND
7
8
9
AGND
DNI 1
JP1
VSS_DUT
2
AGND
IN+
0
R1206
C2
0.1µF
C0805
AGND
RS1
0Ω
13409-020
3
4
5
6
0.1µF
C0805
1
8
+IN
–IN
2
7
GRD GRD
6
3
DNC OUT
4
5
V–
V+
J1
UCBBJR29
AGND
C1
Figure 24. ADA4530-1R-EBZ-TIA Schematic
Rev. 0 | Page 11 of 14
UG-865
ADA4530-1R-EBZ User Guide
1
RF2
DNI
GND_P4_TP
1
2
3
AGND
RS3
DNI
CF1
DNI
RF1
VOUT_TP
1 VOUT
R0
VOUT_ISO 1
499Ω
0Ω
5 4 3 2
GUARD
1
JP2
J2
1-1337445-0
2
IN–
VDD_DUT
DNI
1
2
1
2
3
JP3
SAMTECTSW10608GS3PIN
7
8
9
AGND
AGND
1
JP1
VSS_DUT
2
IN+
0
R1206
C2
0.1µF
C0805
AGND
RS1
DNI
13409-021
3
4
5
6
U1
ADA4530-1
AGND
1
8
+IN
–IN
2
7
GRD GRD
6
3
DNC OUT
4
5
V–
V+
0.1µF
C0805
J1
CBBJR9A
AGND
C1
Figure 25. ADA4530-1R-EBZ-BUF Schematic
Rev. 0 | Page 12 of 14
ADA4530-1R-EBZ User Guide
UG-865
ORDERING INFORMATION
BILL OF MATERIALS
Table 10. Bill of Materials for ADA4530-1R-EBZ-TIA
Qty
1
Reference
Designator
U1
2
2
1
2
1
Manufacturer Part Number
Analog Devices, Inc., ADA4530-1
Distributor
C1, C2
C3, C4
RO
RS1, JP2
RF1
Description
Femtoampere input bias current
electrometer amplifier (device under test)
0.1 μF, 50 V, 5%, 0805
10 μF, 35 V, 10%, 7343
499 Ω, 0.125 W, 1%, 0805
0 Ω, 0.25 W, 0.05%, 1206
10G Ω, 0.25W, 10%, 1206
Kemet, C0805C104J5RACTU
AVX, TPSD106K035R0125
Panasonic, ERJ-6ENF4990V
Panasonic, ERJ-8GEY0R00V
Ohmite, HVC1206Z1008KET
1
J1
BNC connector, right angle
1
1
3
J2
JP3
J3, J4, J5
BNC connector, through hole
3-pin header, 100 mil spacing
Banana jack, panel mount
1
1
3
1
1
3
J6
J7
P4, P7, VOUT
SHIELD1, SHEILD3
SHIELD2
N/A1
Terminal block, 2-position
Terminal block, 3-position
Pin receptacle, 22 mil to 32 mil pin diameter
1.0 x 1.5 x 0.25 RF shield
1.5 x 3.0 x 0.75 RF shield
RF shield clip (to be used with SHIELD2)
Trompeter/Cinch Connectivity,
UCBBJR29
TE Connectivity, 1-1337445-0
Samtec, TSW-103-08-G-S
Emerson Network Power
Connectivity Johnson, 108-0740-001
Keystone, 8718
Keystone, 8719
Mill-Max, 0294-0-15-15-06-27-10-0
Fotofab, DMP-1.0 X 1.5 X 0.25
Fotofab, 1.5 X 3.0 X 0.75
Harwin, Inc., S1711-46R
Digi-Key, 399-1171-6-ND
Digi-Key, 478-3337-2-ND
Digi-Key, P499CCT-ND
Digi-Key, P0.0ECT-ND
Digi-Key,
HVC1206Z1008KETCT-ND
Mouser, 530-UCBBJR29
1
Digi-Key, A101972-ND
Digi-Key, SAM1038-03-ND
Digi-Key, J147-ND
Mouser, 534-8718
Mouser,534-8719
Digi-Key, ED90072-ND
Digi-Key, 655-1015-ND
Digi-Key, 952-1475-1-ND
N/A means not applicable.
Table 11. Bill of Materials for ADA4530-1R-EBZ-BUF
Qty
1
Reference
Designator
U1
2
2
1
3
1
C1, C2
C3, C4
RO
RF1, JP1
J1
Description
Femtoampere Input bias current
electrometer amplifier (device under test)
0.1 μF, 50 V, 5%, 0805
10 μF, 35 V, 10%, 7343
499 Ω, 0.125 W, 1%, 0805
0 Ω, 0.25 W, 0.05%, 1206
Triax connector, right angle, 3-lug
1
1
3
J2
JP3
J3, J4, J5
BNC connector, through hole
3-pin header, 100 mil spacing
Banana jack, panel mount
1
1
3
1
1
3
J6
J7
P4, P7, VOUT
SHIELD1, SHEILD3
SHIELD2
N/A1
Terminal block, 2-position
Terminal block, 3-position
Pin receptacle, 22 mil to 32 mil pin diameter
1.0 x 1.5 x 0.25 RF shield
1.5 x 3.0 x 0.75 RF Shield
RF shield clip (to be used with SHIELD2)
1
Manufacturer Part Number
Analog Devices, Inc., ADA4530-1
Distributor
Kemet, C0805C104J5RACTU
AVX, TPSD106K035R0125
Panasonic, ERJ-6ENF4990V
Panasonic, ERJ-8GEY0R00V
Emerson Network Power
Connectivity Trompeter, CBBJR79/A
TE Connectivity, 1-1337445-0
Samtec TSW-103-08-G-S
Emerson Network Power
Connectivity Johnson, 108-0740-001
Keystone, 8718
Keystone, 8719
Mill-Max, 0294-0-15-15-06-27-10-0
Fotofab, DMP-1.0 X 1.5 X 0.25
Fotofab, 1.5 X 3.0 X 0.75
Harwin, Inc., S1711-46R
Digi-Key, 399-1171-6-ND
Digi-Key, 478-3337-2-ND
Digi-Key, P499CCT-ND
Digi-Key, P0.0ECT-ND
Digi-Key, 1097-1046-ND
N/A means not applicable.
Rev. 0 | Page 13 of 14
Digi-Key, A101972-ND
Digi-Key, SAM1038-03-ND
Digi-Key, J147-ND
Mouser, 534-8718
Mouser, 534-8719
Digi-Key, ED90072-ND
Digi-Key, 655-1015-ND
Digi-Key, 952-1475-1-ND
UG-865
ADA4530-1R-EBZ User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG13409-0-10/15(0)
Rev. 0 | Page 14 of 14
工商网监
湘ICP备2023018690号
