ADBMS6815WCSWZ

12-Channel Multicell Battery Monitor ADBMS6815 Data Sheet FEATURES TYPICAL APPLICATION CIRCUIT 4 MODULES SHOWN MODULE 2 + MODULE N – 1 isoSPI PORT B UP TO 12 CELLS isoSPI PORT A ADBMS6815 –t° –t° ADBMS6815 isoSPI PORT A UP TO 12 CELLS isoSPI PORT B + MODULE 1 + MODULE N isoSPI PORT B UP TO 12 CELLS isoSPI PORT A ADBMS6815 –t° UP TO 12 CELLS –t° ADBMS6815 isoSPI PORT A isoSPI PORT B + BAT+ OPTIONAL REVERSIBLE isoSPI LOOP isoSPI PORT LTC2949 BATTERY PACK MONITOR HV– isoSPI LTC6820 SPI 4 isoSPI LTC6820 SPI 4 BMS CONTROLLER (SAFETY MICROCONTROLLER) CHASSIS GND HV+ 21645-101 HV– HV+ BAT Measures up to 12 battery cells in series Maximum lifetime total measurement error: 1.5 mV Stackable architecture for high voltage battery packs Built-in isoSPI interface 2 Mb isolated serial communications Uses a single twisted pair, up to 20 meters Low EMI susceptibility and emissions Bidirectional for broken wire protection Capacitor or transformer coupled Hot plug tolerant without external protection ADBMS6815WFS models designed for use in ISO 26262 applications for Automotive Safety Integrity Level Capability D (ASIL D) Diagnostics for IC and application circuit failure modes 304 μs to measure all cells in a system 16-bit ADC with programmable noise filter Passive cell balancing up to 300 mA per channel with programmable PWM 7 GPIO or analog inputs Temperature or other sensor inputs Configurable as an I2C or SPI master Sleep state supply current: 5.5 μA 48-lead LQFP package with exposed pad AEC-Q100 qualified for automotive applications Figure 1. Typical Application Circuit APPLICATIONS Electric and hybrid electric vehicles Backup battery systems Grid energy storage Large portable power banks GENERAL DESCRIPTION The ADBMS6815 is a multicell battery stack monitor that measures up to 12 series connected battery cells with a lifetime total measurement error (TME) of less than 1.5 mV. The cell measurement range of 0 V to 5 V makes the ADBMS6815 suitable for most battery chemistries. All 12 cells can be measured in 304 μs, and lower data acquisition rates can be selected for high noise reduction. Multiple ADBMS6815 devices can be connected in series, permitting simultaneous cell monitoring of long, high voltage battery strings. Each ADBMS6815 has an isoSPI™ interface for high speed, RF immune, long distance communications. Multiple devices are connected in a daisy chain with one host processor connection for all devices. This daisy chain can be operated bidirectionally, ensuring communication integrity even in the event of a fault along the communication path. The ADBMS6815 can be powered directly from the battery stack or from an isolated supply. The ADBMS6815 includes passive balancing for each cell, with individual pulse-width modulation (PWM) duty cycle control for each cell. Other features include an on-board 5 V regulator, seven generalpurpose input/output (GPIO) lines, and a sleep state, where current consumption is reduced to 5.5 μA. The ADBMS6815WFS models are designed for use in ISO 26262 applications for Automotive Safety Integrity Level Capability D (ASIL D). For more information on the ADBMS6815, visit the ADBMS6815 product page. Rev. SpA Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2020–2021 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADBMS6815 Data Sheet NOTES ©2020–2021 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D21645F-1/21(SpA) Rev. SpA | Page 2 of 2