I2C® CMOS 8 × 8 Unbuffered Analog
Switch Array with Dual/Single Supplies
ADG2188
Data Sheet
FEATURES
GENERAL DESCRIPTION
I2C-compatible interface
3.4 MHz high speed I2C option
32-lead LFCSP_WQ (5 mm × 5 mm)
Double-buffered input logic
Simultaneous update of multiple switches
Up to 300 MHz bandwidth
Fully specified at dual ±5 V/single +12 V operation
On resistance 35 Ω maximum
Low quiescent current < 20 µA
Qualified for automotive applications
The ADG2188 is an analog cross point switch with an array size of
8 × 8. The switch array is arranged so that there are eight columns
by eight rows, for a total of 64 switch channels. The array is
bidirectional, and the rows and columns can be configured as
either inputs or outputs. Each of the 64 switches can be addressed
and configured through the I2C-compatible interface. Standard,
full speed, and high speed (3.4 MHz) I2C interfaces are supported.
Any simultaneous switch combination is allowed. An additional
feature of the ADG2188 is that switches can be updated simultaneously, using the LDSW command. In addition, a RESET option
allows all of the switch channels to be reset/off. At power on, all
switches are in the off condition. The device is packaged in a
32-lead, 5 mm × 5 mm LFCSP_WQ.
APPLICATIONS
AV switching in TV
Automotive infotainment
AV receivers
CCTV
Ultrasound applications
KVM switching
Telecom applications
Test equipment/instrumentation
PBX systems
FUNCTIONAL BLOCK DIAGRAM
VDD
VL
VSS
ADG2188
SDA
INPUT
REGISTER
AND
7 TO 64
DECODER
LATCHES
64
LDSW
A2 A1 A0
1
1
8 × 8 SWITCH ARRAY
X0 TO X7 (I/O)
64
LDSW
GND
Y0 TO Y7 (I/O)
05897-001
SCL
Figure 1.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2006–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADG2188
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Readback ..................................................................................... 18
Applications ....................................................................................... 1
Serial Interface ................................................................................ 19
General Description ......................................................................... 1
High Speed I2C Interface ........................................................... 19
Functional Block Diagram .............................................................. 1
Serial Bus Address ...................................................................... 19
Revision History ............................................................................... 2
Writing to the ADG2188 ............................................................... 20
Specifications..................................................................................... 3
Input Shift Register .................................................................... 20
I C Timing Specifications ............................................................ 7
Write Operation.......................................................................... 22
Timing Diagram ........................................................................... 8
Read Operation........................................................................... 22
Absolute Maximum Ratings ............................................................ 9
Evaluation Board ............................................................................ 24
ESD Caution .................................................................................. 9
Using the ADG2188 Evaluation Board ................................... 24
Pin Configuration and Function Descriptions ........................... 10
Power Supply............................................................................... 24
Typical Performance Characteristics ........................................... 11
Schematics ................................................................................... 25
Test Circuits ..................................................................................... 15
Outline Dimensions ....................................................................... 27
Terminology .................................................................................... 17
Ordering Guide .......................................................................... 27
Theory of Operation ...................................................................... 18
Automotive Products ................................................................. 27
2
RESET/Power-On Reset ............................................................ 18
Load Switch (LDSW) ................................................................. 18
REVISION HISTORY
7/2017—Rev. A to Rev. B
Changes to Figure 3 ........................................................................ 10
Changes to RESET/Power-On Reset Section .............................. 18
Updated Outline Dimensions ....................................................... 27
Changes to Ordering Guide .......................................................... 27
2/2015—Rev. 0 to Rev. A
Changed NC Pins to DNC Pins .................................................... 10
Updated Outline Dimensions ....................................................... 27
Changes to Ordering Guide .......................................................... 27
Added Automotive Products Section........................................... 27
4/2006—Revision 0: Initial Version
Rev. B | Page 2 of 28
Data Sheet
ADG2188
SPECIFICATIONS
VDD = 12 V ± 10%, VSS = 0 V, VL = 5 V, GND = 0 V, all specifications TMIN to TMAX, unless otherwise noted.1
Table 1.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
On Resistance Matching
Between Channels, ∆RON
On Resistance Flatness, RFLAT(ON)
LEAKAGE CURRENTS
Channel Off Leakage, IOFF
Channel On Leakage, ION
DYNAMIC CHARACTERISTICS2
COFF
CON
tON
tOFF
THD + N
PSRR
−3 dB Bandwidth
Off Isolation
Channel-to-Channel Crosstalk
Adjacent Channels
Nonadjacent Channels
Differential Gain
Differential Phase
Charge Injection
LOGIC INPUTS (Ax, RESET)2
Input High Voltage, VINH
Input Low Voltage, VINL
Input Leakage Current, IIN
B Version
−40°C to
+25°C
+85°C
Y Version
−40°C to
+25°C
+125°C
VDD − 2 V
30
35
32
37
45
50
4.5
8
2.3
3.5
14.5
18
40
42
57
9
4
20
VDD − 2 V
30
35
32
37
45
50
4.5
8
2.3
3.5
14.5
18
47
62
10
5
22
V max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
±0.03
±0.03
±0.03
±0.03
μA typ
μA typ
11
18.5
170
185
210
250
0.04
11
18.5
170
185
210
250
0.04
90
pF typ
pF typ
ns typ
ns max
ns typ
ns max
% typ
dB typ
190
255
195
260
210
16.5
−69
210
16.5
−69
MHz typ
MHz typ
dB typ
−63
−76
0.4
0.6
−3.5
−63
−76
0.4
0.6
−3.5
dB typ
dB typ
% typ
° typ
pC typ
2.0
0.8
0.005
2.0
0.8
0.005
±1
Input Capacitance, CIN
42
Unit
7
±1
7
Rev. B | Page 3 of 28
V min
V max
μA typ
μA max
pF typ
Test Conditions/Comments
VDD = 10.8 V, VIN = 0 V, IS = −10 mA
VDD = 10.8 V, VIN = 1.4 V, IS = −10 mA
VDD = 10.8 V, VIN = 5.4 V, IS = −10 mA
VDD = 10.8 V, VIN = 0 V, IS = −10 mA
VDD = 10.8 V, VIN = 0 V to 1.4 V, IS = −10 mA
VDD = 10.8 V, VIN = 0 V to 5.4 V, IS = −10 mA
VDD = 13.2 V
VX = 7 V/1 V, VY = 1 V/7 V
VX = VY = 1 V or 7 V
RL = 300 Ω, CL = 35 pF
RL = 300 Ω, CL = 35 pF
RL = 10 kΩ, f = 20 Hz to 20 kHz, VS = 1 V p-p
f = 20 kHz; without decoupling; see
Figure 24
Individual inputs to outputs
8 inputs to 1 output
RL = 75 Ω, CL = 5 pF, f = 5 MHz
RL = 75 Ω, CL = 5 pF, f = 5 MHz
RL = 75 Ω, CL = 5 pF, f = 5 MHz
RL = 75 Ω, CL = 5 pF, f = 5 MHz
VS = 4 V, RS = 0 Ω, CL = 1 nF
ADG2188
Parameter
LOGIC INPUTS (SCL, SDA)2
Input High Voltage, VINH
Data Sheet
B Version
−40°C to
+25°C
+85°C
0.7 VL
VL + 0.3
−0.3
0.3 VL
Input Low Voltage, VINL
Input Leakage Current, IIN
Input Hysteresis
Input Capacitance, CIN
LOGIC OUTPUT (SDA)2
Output Low Voltage, VOL
Floating State Leakage Current
POWER REQUIREMENTS
IDD
Y Version
−40°C to
+25°C
+125°C
0.005
0.7 VL
VL + 0.3
−0.3
0.3 VL
0.005
±1
0.05 VL
7
±1
0.05 VL
7
0.4
0.6
±1
0.05
0.4
0.6
±1
0.05
1
ISS
0.05
1
0.05
1
IL
Interface Inactive
1
0.3
Interface Active: 400 kHz fSCL
0.1
Interface Active: 3.4 MHz fSCL
0.4
2
0.1
0.2
0.2
0.4
1.2
2
V min
V max
V min
V max
μA typ
μA max
V min
pF typ
Test Conditions/Comments
VIN = 0 V to VL
V max
V max
μA max
ISINK = 3 mA
ISINK = 6 mA
μA typ
μA max
μA typ
μA max
Digital inputs = 0 V or VL
Digital inputs = 0 V or VL
Digital inputs = 0 V or VL
0.3
2
1
Unit
1.7
Temperature range is as follows: B version: −40°C to +85°C; Y version: −40°C to +125°C.
Guaranteed by design, not subject to production test.
Rev. B | Page 4 of 28
μA typ
μA max
mA typ
mA max
mA typ
mA max
-HS model only
Data Sheet
ADG2188
VDD = +5 V ± 10% , VSS = −5 V ± 10% , VL = 5 V, GND = 0 V, all specifications TMIN to TMAX, unless otherwise noted. 1
Table 2.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
On Resistance Matching
Between Channels, ∆RON
On Resistance Flatness, RFLAT(ON)
B Version
−40°C to
+25°C +85°C
Y Version
−40°C to
+25°C +125°C
34
40
50
55
66
75
4.5
8
17
20
34
34
40
50
55
66
75
4.5
8
17
20
34
VDD − 2 V
42
LEAKAGE CURRENTS
Channel Off Leakage, IOFF
Channel On Leakage, ION
DYNAMIC CHARACTERISTICS 2
COFF
CON
tON
tOFF
THD + N
PSRR
−3 dB Bandwidth
Off Isolation
Channel-to-Channel Crosstalk
Adjacent Channels
Nonadjacent Channels
Differential Gain
Differential Phase
Charge Injection
LOGIC INPUTS (Ax, RESET)2
Input High Voltage, VINH
Input Low Voltage, VINL
Input Leakage Current, IIN
45
65
85
9
23
45
42
95
10
25
48
µA typ
µA typ
6
9.5
170
200
210
250
0.04
300
18
−66
6
9.5
170
200
210
250
0.04
90
300
18
−64
pF typ
pF typ
ns typ
ns max
ns typ
ns max
% typ
dB typ
MHz typ
MHz typ
dB typ
−62
−79
1.5
1.8
−3
−62
−79
1.5
1.8
−3
215
255
2.0
0.8
0.005
220
260
dB typ
dB typ
% typ
° typ
pC typ
2.0
0.8
0.005
7
±1
7
0.7 VL
VL + 0.3
−0.3
0.3 VL
0.005
0.7 VL
VL + 0.3
−0.3
0.3 VL
0.005
±1
±1
Rev. B | Page 5 of 28
Test Conditions/Comments
VDD = +4.5 V, VSS = −4.5 V, VIN = VSS, IS = −10 mA
VDD = +4.5 V, VSS = −4.5 V, VIN = 0 V, IS = −10 mA
VDD = +4.5 V, VSS = −4.5 V, VIN = +1.4 V, IS = −10 mA
VDD = +4.5 V, VSS = −4.5 V, VIN = VSS, IS = −10 mA
VDD = +4.5 V, VSS = −4.5 V, VIN = VSS to 0 V, IS = −10 mA
VDD = +4.5 V, VSS = −4.5 V, VIN = VSS to +1.4 V,
IS = −10 mA
Ω max
±0.03
±0.03
Input Low Voltage, VINL
Input Leakage Current, IIN
70
V max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Ω typ
±0.03
±0.03
±1
Input Capacitance, CIN
LOGIC INPUTS (SCL, SDA)2
Input High Voltage, VINH
50
Unit
VDD = 5.5 V, VSS = 5.5 V
VX = +4.5 V/−2 V, VY = −2 V/+4.5 V
VX = VY = −2 V or +4.5 V
RL = 300 Ω, CL = 35 pF
RL = 300 Ω, CL = 35 pF
RL = 10 kΩ, f = 20 Hz to 20 kHz, VS = 1 V p-p
f = 20 kHz; without decoupling; see Figure 24
Individual inputs to outputs
8 inputs to 1 output
RL = 75 Ω, CL = 5 pF, f = 5 MHz
RL = 75 Ω, CL = 5 pF, f = 5 MHz
RL = 75 Ω, CL = 5 pF, f = 5 MHz
RL = 75 Ω, CL = 5 pF, f = 5 MHz
VS = 0 V, RS = 0 Ω, CL = 1 nF
V min
V max
µA typ
µA max
pF typ
V min
V max
V min
V max
µA typ
µA max
VIN = 0 V to VL
ADG2188
Parameter
Input Hysteresis
Input Capacitance, CIN
LOGIC OUTPUT (SDA)2
Output Low Voltage, VOL
Floating State Leakage Current
POWER REQUIREMENTS
IDD
Data Sheet
B Version
−40°C to
+25°C +85°C
0.05 VL
7
Y Version
−40°C to
+25°C +125°C
0.05 VL
7
0.4
0.6
±1
0.05
0.4
0.6
±1
0.005
1
ISS
0.05
1
0.005
1
1
Unit
V min
pF typ
Test Conditions/Comments
V max
V max
µA max
ISINK = 3 mA
ISINK = 6 mA
µA typ
µA max
µA typ
µA max
Digital inputs = 0 V or VL
IL
Digital inputs = 0 V or VL
Interface Inactive
0.3
Interface Active: 400 kHz fSCL
0.1
Interface Active: 3.4 MHz fSCL
0.4
0.3
2
2
0.1
0.1
2
0.1
0.4
0.3
1
Digital inputs = 0 V or VL
0.3
Temperature range is as follows: B version: –40°C to +85°C; Y version: –40°C to +125°C.
Guaranteed by design, not subject to production test.
Rev. B | Page 6 of 28
µA typ
µA max
mA typ
mA max
mA typ
mA max
-HS model only
Data Sheet
ADG2188
I2C TIMING SPECIFICATIONS
VDD = 5 V to 12 V; VSS = −5 V to 0 V; VL = 5 V; GND = 0 V; TA = TMIN to TMAX, unless otherwise noted (see Figure 2).
Table 3.
Parameter 1
fSCL
t1
t2
t3
t4 3
t5
t6
t7
t8
t9
t10
Test Conditions/Comments
Standard mode
Fast mode
High speed mode 2
CB = 100 pF maximum
CB = 400 pF maximum
Standard mode
Fast mode
High speed mode2
CB = 100 pF maximum
CB = 400 pF maximum
Standard mode
Fast mode
High speed mode2
CB = 100 pF maximum
CB = 400 pF maximum
Standard mode
Fast mode
High speed mode2
Standard mode
Fast mode
High speed mode2
CB = 100 pF maximum
CB = 400 pF maximum
Standard mode
Fast mode
High speed mode2
Standard mode
Fast mode
High speed mode2
Standard mode
Fast mode
Standard mode
Fast mode
High speed mode2
Standard mode
Fast mode
High speed mode2
CB = 100 pF maximum
CB = 400 pF maximum
Standard mode
Fast mode
High speed mode2
CB = 100 pF maximum
CB = 400 pF maximum
ADG2188 Limit at TMIN, TMAX
Min
Max
Unit
100
kHz
400
kHz
3.4
1.7
4
0.6
MHz
MHz
µs
µs
60
120
4.7
1.3
ns
ns
µs
µs
160
320
250
100
10
0
0
ns
ns
ns
ns
ns
µs
µs
0
0
4.7
0.6
160
4
0.6
160
4.7
1.3
4
0.6
160
3.45
0.9
1000
300
ns
ns
µs
µs
ns
µs
µs
ns
µs
µs
µs
µs
ns
ns
ns
20 + 0.1 CB
80
160
300
300
ns
ns
ns
ns
10
20
80
160
ns
ns
20 + 0.1 CB
10
20
70
150
Rev. B | Page 7 of 28
Description
Serial clock frequency
tHIGH, SCL high time
tLOW, SCL low time
tSU;DAT, data setup time
tHD;DAT, data hold time
tSU;STA, setup time for a repeated start condition
tHD;STA, hold time for a (repeated) start condition
tBUF, bus free time between a stop and a start condition
tSU;STO, setup time for a stop condition
tRDA, rise time of SDA signal
tFDA, fall time of SDA signal
ADG2188
Parameter 1
t11
t11A
t12
tSP
Data Sheet
Test Conditions/Comments
Standard mode
Fast mode
High speed mode2
CB = 100 pF maximum
CB = 400 pF maximum
Standard mode
Fast mode
High speed mode2
CB = 100 pF maximum
CB = 400 pF maximum
Standard mode
Fast mode
High speed mode2
CB = 100 pF maximum
CB = 400 pF maximum
Fast mode
High speed mode2
ADG2188 Limit at TMIN, TMAX
Min
Max
Unit
1000
ns
20 + 0.1 CB
300
ns
10
20
40
80
1000
300
ns
ns
ns
ns
20 + 0.1 CB
80
160
300
300
ns
ns
ns
ns
10
20
0
0
40
80
50
10
ns
ns
ns
ns
20 + 0.1 CB
10
20
Description
tRCL, rise time of SCL signal
tRCL1, rise time of SCL signal after a repeated start condition
and after an acknowledge bit
tFCL, fall time of SCL signal
Pulse width of suppressed spike
Guaranteed by initial characterization. All values measured with input filtering enabled. CB refers to capacitive load on the bus line; tR and tF are measured between
0.3 VDD and 0.7 VDD.
High speed I2C is available only in -HS models
3
A device must provide a data hold time for SDA to bridge the undefined region of the SCL falling edge.
1
2
TIMING DIAGRAM
t2
t11
t12
t6
SCL
t6
t4
t5
t3
t8
t1
t9
t10
SDA
t7
S
S
P
05897-002
P
S = START CONDITION
P = STOP CONDITION
Figure 2. Timing Diagram for 2-Wire Serial Interface
Rev. B | Page 8 of 28
Data Sheet
ADG2188
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 4.
Parameter
VDD to VSS
VDD to GND
VSS to GND
VL to GND
Analog Inputs
Digital Inputs
Continuous Current
10 V on Input; Single Input
Connected to Single Output
1 V on Input; Single Input
Connected to Single Output
10 V on Input; Eight Inputs
Connected to Eight Outputs
Operating Temperature Range
Industrial (B Version)
Automotive (Y Version)
Storage Temperature Range
Junction Temperature
32-Lead LFCSP_WQ
θJA Thermal Impedance
Reflow Soldering (Pb Free)
Peak Temperature
Time at Peak Temperature
Rating
15 V
−0.3 V to +15 V
+0.3 V to −7 V
−0.3 V to +7 V
VSS − 0.3 V to VDD + 0.3 V
−0.3 V to VL + 0.3 V or 30 mA,
whichever occurs first
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
65 mA
90 mA
25 mA
–40°C to +85°C
–40°C to +125°C
–65°C to +150°C
150°C
108.2°C/W
260°C (+0/–5)
10 sec to 40 sec
Rev. B | Page 9 of 28
ADG2188
Data Sheet
32
31
30
29
28
27
26
25
GND
RESET
A2
A1
A0
SCL
SDA
VL
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
ADG2188
TOP VIEW
(Not to Scale)
24
23
22
21
20
19
18
17
VDD
DNC
DNC
DNC
DNC
DNC
X7
X6
NOTES
1. NC = NO CONNECT.
2. THE EXPOSED PADDLE IS SOLDERED TO VSS.
05897-003
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
9
10
11
12
13
14
15
16
VSS
DNC
X0
X1
X2
X3
X4
X5
Figure 3. Pin Configuration
Table 5. Pin Function Descriptions
1
Pin No.
1
2, 19 to 23
3 to 8,
17, 18
9 to 16
24
25
26
27
Mnemonic
VSS
DNC
X0 to X7
Description
Negative Power Supply in a Dual-Supply Application. For single-supply applications, this pin must be tied to GND.
Do No Connect.
Can be inputs or outputs.
Y0 to Y7
VDD
VL
SDA
SCL
28
29
30
31
32
A0
A1
A2
RESET
GND
EPAD
Can be inputs or outputs.
Positive Power Supply Input.
Logic Power Supply Input.
Digital I/O. Bidirectional open drain data line. External pull-up resistor required.
Digital Input, Serial Clock Line. Open drain input that is used in conjunction with SDA to clock data into the
device. External pull-up resistor required.
Logic Input. Address pin that sets the least significant bit of the 7-bit slave address.
Logic Input. Address pin that sets the second least significant bit of the 7-bit slave address.
Logic Input. Address pin that sets the third least significant bit of the 7-bit slave address.
Active Low Logic Input. When this pin is low, all switches are open, and appropriate registers are cleared to 0.
Ground. Reference point for all circuitry on the ADG2188.
Exposed Paddle. The exposed paddle is soldered to VSS.
1
It is recommended that the exposed paddle be soldered to VSS to improve heat dissipation and crosstalk.
Rev. B | Page 10 of 28
Data Sheet
ADG2188
TYPICAL PERFORMANCE CHARACTERISTICS
90
TA = 25°C
IDS = 10mA
200
TA = 25°C
180 IDS = 10mA
80
VDD = 7.2V
160
RON (Ω)
VSS = 0V
VDD = +8V
140
VSS = –5V
VDD = +5V
120
100
80
VDD = 8V
60
50
60
VDD = 8.8V
20
1
2
3
4
5
6
7
8
9 10 11 12
SOURCE VOLTAGE (V)
0
0.5
80
TA = 25°C
IDS = 10mA
2.5
3.0
VDD = +5V
VSS = –5V
IDS = 10mA
70
VDD/VSS = ±4.5V
3.5
4.0
4.5
5.0
TA = +125°C
60
65
TA = +85°C
50
VDD/VSS = ±5V
RON (Ω)
55
40
TA = +25°C
30
45
35
TA = –40°C
20
VDD/VSS = ±5.5V
10
–4.5
–3.5
–2.5
–1.5
–0.5
0.5
0
–5
05897-017
25
–5.5
1.5
SOURCE VOLTAGE (V)
60
VDD = 10.8V
60
–2
–1
0
VDD = 12V
VSS = 0V
IDS = 10mA
50
55
1
TA = +125°C
TA = +85°C
40
VDD = 12V
RON (Ω)
50
–3
Figure 8. RON vs. Temperature, Dual ±5 V Supplies
70
TA = 25°C
IDS = 10mA
–4
SOURCE VOLTAGE (V)
Figure 5. RON vs. Source Voltage, Dual ±5 V Supplies
65
05464-026
RON (Ω)
2.0
Figure 7. RON vs. Source Voltage, VDD = 8 V ± 10%
85
45
TA = +25°C
30
TA = –40°C
40
20
35
VDD = 13.2V
30
10
25
20
0
1
2
3
4
5
6
SOURCE VOLTAGE (V)
7
8
05897-018
RON (Ω)
1.5
SOURCE VOLTAGE (V)
Figure 4. Signal Range
75
1.0
05897-007
30
0
–5 –4 –3 –2 –1 0
05897-025
40
VSS = 0V
VDD = +12V
40
Figure 6. RON vs. Supplies, VDD = 12 V ± 10%
0
0
1
2
3
4
SOURCE VOLTAGE (V)
Figure 9. RON vs. Temperature, VDD = 12 V
Rev. B | Page 11 of 28
5
6
05897-027
RON (Ω)
70
ADG2188
Data Sheet
80
18
VDD = 8V
VSS = 0V
IDS = 10mA
TA = +125°C
60
TA = +85°C
50
RON (Ω)
Y CHANNELS, VBIAS = 7V
14
LEAKAGE CURRENTS (nA)
70
VDD = 12V
VSS = 0V
16
40
TA = +25°C
30
TA = –40°C
20
X CHANNELS, VBIAS = 7V
12
10
8
Y CHANNELS, VBIAS = 1V
6
4
2
10
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
SOURCE VOLTAGE (V)
40
60
9
LEAKAGE CURRENTS (nA)
LEAKAGE CURRENTS (nA)
X CHANNELS,
VBIAS = +4V
6
Y CHANNELS,
VBIAS = –2V
4
120
X, Y CHANNELS;
VBIAS = 7V ON X CHANNEL;
1V ON Y CHANNEL
7
12
8
100
VDD = 12V
VSS = 0V
8
10
80
Figure 13. On Leakage vs. Temperature, 12 V Single Supply
VDD = +5V
VSS = –5V
14
20
TEMPERATURE (°C)
Figure 10. RON vs. Temperature, VDD = 8 V
16
0
05897-011
0
–2
05897-013
0
6
5
4
3
X, Y CHANNELS;
VBIAS = 1V ON X CHANNEL;
7V ON Y CHANNEL
2
1
2
20
40
60
80
100
120
TEMPERATURE (°C)
–1
20
40
60
80
100
120
TEMPERATURE (°C)
Figure 11. On Leakage vs. Temperature, Dual ±5 V Supplies
12
0
05897-012
0
05897-014
0
0
Figure 14. Off Leakage vs. Temperature, 12 V Single Supply
0
VDD = +5V
VSS = –5V
–0.5
10
CHARGE INJECTION (pC)
8
X, Y CHANNELS;
VBIAS = +4V ON X CHANNEL;
–2V ON Y CHANNEL
6
4
X, Y CHANNELS;
VBIAS = –2V ON X CHANNEL;
+4V ON Y CHANNEL
2
–1.5
–2.0
–2.5
–3.0
–3.5
VDD = +5V, VSS = –5V
–4.0
0
VDD = +12V, VSS = 0V
–4.5
0
20
40
60
80
100
120
TEMPERATURE (°C)
Figure 12. Off Leakage vs. Temperature, Dual ±5 V Supplies
–5.0
–5
–3
–1
1
3
5
7
9
SUPPLY VOLTAGE (V)
Figure 15. Charge Injection vs. Supply Voltage
Rev. B | Page 12 of 28
11
05897-030
–2
05897-015
LEAKAGE CURRENTS (nA)
–1.0
Data Sheet
ADG2188
0
–1
220
–2
tON/tOFF (ns)
200
INSERTION LOSS (dB)
240
tOFF
VDD = +5V, VSS = –5V
180
tON
160
VDD = 12V, VSS = 0V
–3
–4
–5
–6
140
–8
10
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
–10
–20
–3
1G
10G
VDD = +5V TO +12V
VSS = –5V TO 0V
TA = 25°C
INSERTION LOSS (dB)
–30
–4
–5
–6
–40
–50
–60
–70
–80
–90
VDD = +5V
VSS = –5V
TA = 25°C
100k
10M
1G
10G
FREQUENCY (Hz)
–110
10
1k
100k
10M
1G
05897-023
1k
1G
05897-024
–100
05897-020
INSERTION LOSS (dB)
10M
Figure 19. One Input to Eight Outputs Bandwidth, ±5 V Dual Supply
–2
–8
10
100k
FREQUENCY (Hz)
Figure 16. tON/tOFF Times vs. Temperature
–7
1k
05897-029
100
–40
VDD = +5V
VSS = –5V
TA = 25°C
05897-022
–7
120
FREQUENCY (Hz)
Figure 17. Individual Inputs to Individual Outputs Bandwidth,
Dual ±5 V Supply
Figure 20. Off Isolation vs. Frequency
–1
–20
INSERTION LOSS (dB)
–3
–4
–5
–6
–7
–8
10
VDD = 12V
VSS = 0V
TA = 25°C
VDD = +5V TO +12V
VSS = –5V TO 0V
TA = 25°C
–40
ADJACENT
CHANNELS
–60
–80
NON-ADJACENT
CHANNELS
–100
1k
100k
10M
1G
10G
FREQUENCY (Hz)
05897-021
INSERTION LOSS (dB)
–2
Figure 18. Individual Inputs to Individual Outputs Bandwidth,
12 V Single Supply
–120
10
1k
100k
10M
FREQUENCY (Hz)
Figure 21. Crosstalk vs. Frequency
Rev. B | Page 13 of 28
ADG2188
0.35
Data Sheet
0
VDD = +5V
VSS = –5V
0.30
VDD = 5V/12V
VSS = –5V/0V
TA = 25°C
0.2V p-p RIPPLE
–20
VL = 5V
SWITCH ON,
WITHOUT DECOUPLING
0.25
ACPSRR (dB)
0.20
0.15
–100
0.5
1.0
1.5
2.0
2.5
–120
100
05897-016
0
3.0
FREQUENCY (MHz)
1.6
VL = 5V
1.2
1.0
0.8
0.6
0.4
0
1
2
3
VLOGIC (V)
4
5
6
05897-019
VL = 3V
0.2
10k
100k
1M
Figure 24. ACPSRR
1.8
1.4
1k
FREQUENCY (Hz)
Figure 22. Digital Curr
ent (IL) vs. Frequency
IL (mA)
WITH DECOUPLING
VL = 3V
0.05
0
–60
–80
0.10
0
SWITCH OFF,
WITHOUT DECOUPLING
Figure 23. Digital Current (IL) vs. VLOGIC for Varying Digital Supply Voltage
Rev. B | Page 14 of 28
10M
100M
1G
05897-028
IL (mA)
–40
Data Sheet
ADG2188
TEST CIRCUITS
The test circuits show measurements on one channel for clarity, but the circuit applies to any of the switches in the matrix.
IDS
V1
VS
05897-031
Y
X
RON = V1/IDS
Figure 25. On Resistance
IOFF
X
A
Y
A
VX
05897-032
IOFF
VY
Figure 26. Off Leakage
Y
A
VY
05897-033
ION
X
NC
Figure 27. On Leakage
0.1µF
VDD
VSS
VDD
VSS
X
0.1µF
50%
9TH DATA BIT
VOUT
Y
90%
RL
300Ω
VX
CL
35pF
VOUT
tOFF AND tON
05897-034
GND
Figure 28. Switching Times, tON, tOFF
RX
VSS
VDD
VSS
X
0.1 µF
SW ON
Y
VOUT
SW OFF
DATA BIT
CL
1nF
VX
ΔVOUT
VOUT
GND
QINJ = CL × ΔVOUT
Figure 29. Charge Injection
Rev. B | Page 15 of 28
05897-035
0.1 µF
VDD
ADG2188
Data Sheet
VDD
VSS
NETWORK
ANALYZER
VSS
VDD
50Ω
NETWORK
ANALYZER
VSS
50Ω
X
50Ω
X
0.1µF
VX
VX
Y
Y
V
RL
50Ω
OFF ISOLATION = 20 log
V
RL
50Ω
GND
05897-036
GND
VOUT
VOUT
VS
INSERTION LOSS = 20 log
VOUT WITH SWITCH
VOUT WITHOUT SWITCH
Figure 31. Bandwidth
Figure 30. Off Isolation
VDD
VSS
0.1µF
NETWORK
ANALYZER
0.1µF
VSS
VDD
VOUT
RL
50Ω
Y1
X1
X2
Y2
R
50Ω
50Ω
VX
R
50Ω
DATA
BIT
CHANNEL-TO-CHANNEL CROSSTALK = 20 log
GND
VOUT
VS
Figure 32. Channel-to-Channel Crosstalk
Rev. B | Page 16 of 28
VOUT
05897-037
VDD
VSS
0.1µF
0.1µF
05897-038
VDD
0.1µF
Data Sheet
ADG2188
TERMINOLOGY
On Resistance (RON)
The series on-channel resistance measured between the
X input/output and the Y input/output.
Total Harmonic Distortion + Noise (THD + N)
The ratio of the harmonic amplitudes plus noise of a signal to
the fundamental.
On Resistance Match (∆RON)
The channel-to-channel matching of on resistance when
channels are operated under identical conditions.
−3 dB Bandwidth
The frequency at which the output is attenuated by 3 dB.
On Resistance Flatness (RFLAT(ON))
The variation of on resistance over the specified range produced
by the specified analog input voltage change with a constant
load current.
Channel Off Leakage (IOFF)
The sum of leakage currents into or out of an off channel input.
Channel On Leakage (ION)
The current loss/gain through an on-channel resistance,
creating a voltage offset across the device.
Input Leakage Current (IIN)
The current flowing into a digital input when a specified low
level or high level voltage is applied to that input.
Input Off Capacitance (COFF)
The capacitance between an analog input and ground when the
switch channel is off.
Input/Output On Capacitance (CON)
The capacitance between the inputs or outputs and ground
when the switch channel is on.
Off Isolation
The measure of unwanted signal coupling through an off switch.
Crosstalk
The measure of unwanted signal that is coupled through from
one channel to another as a result of parasitic capacitance.
Differential Gain
The measure of how much color saturation shift occurs when
the luminance level changes. Both attenuation and amplification
can occur; therefore, the largest amplitude change between any
two levels is specified and is expressed as a percentage of the
largest chrominance amplitude.
Differential Phase
The measure of how much hue shift occurs when the luminance
level changes. It can be a negative or positive value and is expressed
in degrees of subcarrier phase.
Charge Injection
The measure of the glitch impulse transferred from the digital
input to the analog output during on/off switching.
Input High Voltage (VINH)
The minimum input voltage for Logic 1.
Digital Input Capacitance (CIN)
The capacitance between a digital input and ground.
Input Low Voltage (VINL)
The maximum input voltage for Logic 0.
Output On Switching Time (tON)
The time required for the switch channel to close. The time is
measured from 50% of the logic input change to the time the
output reaches 10% of the final value.
Output Low Voltage (VOL)
The minimum input voltage for Logic 1.
Output Off Switching Time (tOFF)
The time required for the switch to open. This time is measured
from 50% of the logic input change to the time the output
reaches 90% of the switch off condition.
IDD
Positive supply current.
Input Low Voltage (VINL)
The maximum output voltage for Logic 0.
ISS
Negative supply current.
Rev. B | Page 17 of 28
ADG2188
Data Sheet
THEORY OF OPERATION
The ADG2188 is an analog cross point switch with an array size
of 8 × 8. The eight rows are referred to as the X input/output
lines, and the eight columns are referred to as the Y input/output
lines. The device is fully flexible in that it connects any X line or
number of X lines with any Y line when turned on. Similarly, it
connects any X line with any number of Y lines when turned on.
Control of the ADG2188 is carried out via an I2C interface. The
device can be operated from single supplies of up to 13.2 V or
from dual ±5 V supplies. The ADG2188 has many attractive
features, such as the ability to reset all the switches, the ability to
update many switches at the same time, and the option of reading
back the status of any switch. All of these features are described
in more detail here in the Theory of Operation section.
RESET/POWER-ON RESET
The ADG2188 offers the ability to reset all of the 64 switches
to the off state. This is done through the RESET pin. When the
RESET pin is low, all switches are open (off), and appropriate
registers are cleared. Note that the ADG2188 also has a poweron reset block. This ensures that all switches are in the off
condition at power-up of the device. In addition, all internal
registers are filled with 0s and remain so until a valid write
to the ADG2188 takes place.
The digital section of the ADG2188 goes through an initialization
phase during the RESET power up. This initialization also occurs
after a hardware or software reset. After reset, ensure that a
minimum of 200 ns from the time of power-up or reset before
any I2Ccommand is issued.
Ensure that RESET does not drop out during the 200 ns
initialization phase because it can result in an incorrect
operation of the ADG2188.
Ensure a minimum of 50 ns reset pulse width to achieve a
complete reset.
LOAD SWITCH (LDSW)
LDSW is an active high command that allows a number of
switches to be simultaneously updated. This is useful in
applications where it is important to have synchronous
transmission of signals. There are two LDSW modes: the
transparent mode and the latched mode.
Transparent Mode
In this mode, the switch position changes after the new word is
written into the input shift register. LDSW is set to 1.
Latched Mode
In this mode, the switch positions are not updated at the same
time that the input registers are written to. This is achieved by
setting LDSW to 0 for each word (apart from the last word) written
to the device. Then, setting LDSW to 1 for the last word allows
all of the switches in that sequence to be simultaneously
updated.
READBACK
Readback of the switch array conditions is also offered when in
standard mode and fast mode. Readback enables the user to
check the status of the switches of the ADG2188. This is very
useful when debugging a system.
Rev. B | Page 18 of 28
Data Sheet
ADG2188
SERIAL INTERFACE
The ADG2188 is controlled via an I2C-compatible serial bus.
The devices are connected to this bus as a slave device (no clock
is generated by the switch).
2.
HIGH SPEED I2C INTERFACE
In addition to standard and full speed I2C, the ADG2188 also
supports the high speed (3.4 MHz) I2C interface. Only the –HS
models provide this added performance. See the Ordering
Guide for details.
SERIAL BUS ADDRESS
The ADG2188 has a 7-bit slave address. The four MSBs are
hard coded to 1110, and the three LSBs are determined by the
state of Pin A0, Pin A1, and Pin A2. By offering the facility to
hardware configure Pin A0, Pin A1, and Pin A2, up to eight of
these devices can be connected to a single serial bus.
The 2-wire serial bus protocol operates as follows:
1.
The master initiates data transfer by establishing a start
condition, defined as when a high-to-low transition on the
SDA line occurs while SCL is high. This indicates that an
address/data stream follows. All slave peripherals connected to
the serial bus respond to the start condition and shift in the
next eight bits, consisting of a 7-bit address (MSB first) plus an
R/W bit that determines the direction of the data transfer,
that is, whether data is written to or read from the slave device.
3.
4.
The peripheral whose address corresponds to the transmitted
address responds by pulling the SDA line low during the
ninth clock pulse, known as the acknowledge bit. At this
stage, all other devices on the bus remain idle while the
selected device waits for data to be written to or read from
its serial register. If the R/W bit is 1 (high), the master reads
from the slave device. If the R/W bit is 0 (low), the master
writes to the slave device.
Data is transmitted over the serial bus in sequences of nine
clock pulses: eight data bits followed by an acknowledge bit
from the receiver of the data. Transitions on the SDA line must
occur during the low period of the clock signal, SCL, and
remain stable during the high period of SCL, because a lowto-high transition when the clock is high can be interpreted as
a stop signal.
When all data bits have been read or written, a stop condition
is established by the master. A stop condition is defined as
a low-to-high transition on the SDA line while SCL is high.
In write mode, the master pulls the SDA line high during
the 10th clock pulse to establish a stop condition. In read
mode, the master issues a no acknowledge for the ninth clock
pulse (that is, the SDA line remains high). The master then
brings the SDA line low before the 10th clock pulse and then
high during the 10th clock pulse to establish a stop condition.
Refer to Figure 33 and Figure 34 for a graphical explanation of
the serial data transfer protocol.
Rev. B | Page 19 of 28
ADG2188
Data Sheet
WRITING TO THE ADG2188
INPUT SHIFT REGISTER
The input shift register is 24 bits wide. A 3-byte write is necessary when writing to this register and is done under the control of the serial
clock input, SCL. The contents of the three bytes of the input shift register are shown in Figure 33 and described in Table 6.
1
1
1
0
A2
A1
A0
R/W
DB8 (LSB)
DB15 (MSB)
DATA AX3 AX2 AX1 AX0 AY2 AY1 AY0
DEVICE ADDRESS
DATA BITS
DB0 (LSB)
DB7 (MSB)
X
X
X
X
X
X
DATA BITS
X
LDSW
05897-004
DB16 (LSB)
DB23 (MSB)
Figure 33. Data-Words
Table 6. Input Shift Register Bit Function Descriptions
Bit
DB23 to DB17
Mnemonic
1110xxx
DB16
R/W
DB15
Data
DB14 to DB11
DB10 to DB8
DB7 to DB1
DB0
AX3 to AX0
AY2 to AY0
X
LDSW
Description
The MSBs of the ADG2188 are set to 1110. The LSBs of the address byte are set by the state of the
three address pins, Pin A0, Pin A1, and Pin A2.
Controls whether the ADG2188 slave device is read from or written to.
If R/W = 1, the ADG2188 is being read from.
If R/W = 0, the ADG2188 is being written to.
Controls whether the switch is to be open (off ) or closed (on).
If Data = 0, the switch is open/off.
If Data = 1, the switch is closed/on.
Controls I/Os X0 to X7. See Table 7 for the decode truth table.
Controls I/Os Y0 to Y7. See Table 7 for the decode truth table.
Don’t care.
This bit is useful when a number of switches need to be updated simultaneously.
If LDSW = 1, the switch position changes after the new word is read in.
If LDSW = 0, the input data is latched, but the switch position is not changed.
As shown in Table 6, Bit DB11 to Bit DB14 control the X input/output lines, while Bit DB8 to Bit DB10 control the Y input/output lines.
Table 7 shows the truth table for these bits. Note that the full coding sequence is written out for Channel Y0, and Channel Y1 to Channel Y7
follow a similar pattern. Note also that the RESET pin must be high when writing to the device.
Table 7. Address Decode Truth Table
DB15
DATA
1
0
1
0
1
0
1
0
1
0
1
0
X
X
1
0
1
0
X
DB14
AX3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
DB13
AX2
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
DB12
AX1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
0
0
1
DB11
AX0
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
0
1
1
0
DB10
AY2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DB9
AY1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Rev. B | Page 20 of 28
DB8
AY0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Switch Configuration
X0 to Y0 (on)
X0 to Y0 (off )
X1 to Y0 (on)
X1 to Y0 (off )
X2 to Y0 (on)
X2 to Y0 (off )
X3 to Y0 (on)
X3 to Y0 (off )
X4 to Y0 (on)
X4 to Y0 (off )
X5 to Y0 (on)
X5 to Y0 (off )
Reserved
Reserved
X6 to Y0 (on)
X6 to Y0 (off )
X7 to Y0 (on)
X7 to Y0 (off )
Reserved
Data Sheet
DB15
DATA
X
X
X
X
X
1
0
..
1
1
0
..
1
1
0
..
1
1
0
..
1
1
0
..
1
1
0
..
1
1
0
..
1
DB14
AX3
1
1
1
1
1
0
0
..
1
0
0
..
1
0
0
..
1
0
0
..
1
0
0
..
1
0
0
..
1
0
0
..
1
ADG2188
DB13
AX2
0
1
1
1
1
0
0
..
0
0
0
..
0
0
0
..
0
0
0
..
0
0
0
..
0
0
0
..
0
0
0
..
0
DB12
AX1
1
0
0
1
1
0
0
..
0
0
0
..
0
0
0
..
0
0
0
..
0
0
0
..
0
0
0
..
0
0
0
..
0
DB11
AX0
1
0
1
0
1
0
0
..
1
0
0
..
1
0
0
..
1
0
0
..
1
0
0
..
1
0
0
..
1
0
0
..
1
DB10
AY2
0
0
0
0
0
0
0
..
0
0
0
..
0
0
0
..
0
1
1
..
1
1
1
..
1
1
1
..
1
1
1
..
1
DB9
AY1
0
0
0
0
0
0
0
..
0
1
1
..
1
1
1
..
1
0
0
..
0
0
0
..
0
1
1
..
1
1
1
..
1
Rev. B | Page 21 of 28
DB8
AY0
0
0
0
0
0
1
1
..
1
0
0
..
0
1
1
..
1
0
0
..
0
1
1
..
1
0
0
..
0
1
1
..
1
Switch Configuration
Reserved
Reserved
Reserved
Reserved
Reserved
X0 to Y1 (on)
X0 to Y1 (off )
X7 to Y1 (on)
X0 to Y2 (on)
X0 to Y2 (off )
X7 to Y2 (on)
X0 to Y3 (on)
X0 to Y3 (off )
X7 to Y3 (on)
X0 to Y4 (on)
X0 to Y4 (off )
X7 to Y4 (on)
X0 to Y5 (on)
X0 to Y5 (off )
X7 to Y5 (on)
X0 to Y6 (on)
X0 to Y6 (off )
X7 to Y6 (on)
X0 to Y7 (on)
X0 to Y7 (off )
X7 to Y7 (on)
ADG2188
Data Sheet
WRITE OPERATION
b.
When writing to the ADG2188, the user must begin with an
address byte and R/W bit, after which the switch acknowledges
that it is prepared to receive data by pulling SDA low. This address
byte is followed by the two 8-bit words. The write operations for
the switch array are shown in Figure 34. Note that it is only the
condition of the switch corresponding to the bits in the data bytes
that changes state. All other switches retain their previous
condition.
Enter the readback address for the X line of interest,
the addresses of which are shown in Table 8. Note that
the ADG2188 is expecting a 2-byte write; therefore, be
sure to also enter another byte of don’t cares (see
Figure 35).
c.
The ADG2188 then places the status of those eight
switches in a register than can be read back.
2.
READ OPERATION
Readback on the ADG2188 is designed to work as a tool for
debug and can output the status of any of the 64 switches of the
device. The readback function is a two-step sequence that works
as follows:
1.
The second step involves reading back from the register
that holds the status of the eight switches associated with
the X line of choice.
a.
As before, enter the I2C address of the ADG2188. This
time, set the R/W to 1 to indicate a read back from the
device.
d.
As with a write to the device, the ADG2188 outputs a
2-byte sequence during readback. Therefore, the first
eight bits of data out that are read back are all 0s. The
next eight bits of data that come back are the status of
the eight Y lines attached to that particular X line. If
the bit is a 1, then the switch is closed (on); similarly, if
the bit is a 0, the switch is open (off).
Select the relevant X line to be read back from. Note that
there are eight switches connecting that X line to the eight
Y lines. The next step involves writing to the ADG2188 to
tell the device to reveal the status of those eight switches.
a.
Enter the I2C address of the ADG2188, and set the
R/W to 0 to indicate a write to the device.
The entire read sequence is shown in Figure 35.
SCL
START
COND
BY
MASTER
A1
A0
DATA
R/W
AX3
ACK
BY
SWITCH
ADDRESS BYTE
AX2
AX1
AX0
AY2
AY1
AY0
DATA BYTE
x
x
x
ACK
BY
SWITCH
x
x
x
DATA BYTE
x
LDSW
ACK
BY
SWITCH
STOP
COND
BY
MASTER
Figure 34. Write Operation
Table 8. Readback Addresses for Each X Line
X Line
X0
X1
X2
X3
X4
X5
X6
X7
RB7
0
0
0
0
0
0
0
0
RB6
0
0
1
1
0
0
1
1
RB5
1
1
1
1
1
1
1
1
RB4
1
1
1
1
1
1
1
1
Rev. B | Page 22 of 28
RB3
0
1
0
1
0
1
0
1
RB2
1
1
1
1
1
1
1
1
RB1
0
0
0
0
0
0
0
0
RB0
0
0
0
0
1
1
1
1
05897-005
A2
SDA
Data Sheet
ADG2188
SCL
A2
SDA
START
COND
BY
MASTER
A1
A0
RB7
R/W
ACK
BY
SWITCH
ADDRESS BYTE
RB6
RB5
RB4
RB3
RB2
RB1
RB0
DATA BYTE
x
x
x
ACK
BY
SWITCH
x
x
x
x
x
NO ACK
BY
SWITCH
DATA BYTE
STOP
COND
BY
MASTER
SCL
START
COND
BY
MASTER
ADDRESS BYTE
A1
A0
Y7
R/W
ACK
BY
SWITCH
DUMMY READBACK BYTE
Figure 35. Read Operation
Rev. B | Page 23 of 28
ACK
BY
MASTER
Y6
Y5
Y4
Y3
Y2
READBACK BYTE
Y1
Y0
NO ACK
BY
MASTER
STOP
COND
BY
MASTER
05897-006
A2
SDA
ADG2188
Data Sheet
EVALUATION BOARD
The ADG2188 evaluation board allows designers to evaluate
the high performance 8 × 8 switch array of the ADG2188 with a
minimum of effort.
The evaluation kit includes a populated, tested ADG2188
printed circuit board. The evaluation board interfaces to the
USB port of a PC, or it can be used as a standalone evaluation
board. Software is available with the evaluation board that allows
the user to easily program the ADG2188 through the USB port.
Schematics of the evaluation board are shown in Figure 36 and
Figure 37. The software runs on any PC that has Microsoft®
Windows® 2000 or Windows XP installed.
USING THE ADG2188 EVALUATION BOARD
The ADG2188 evaluation kit is a test system designed to
simplify the evaluation of the ADG2188. Each input/output
of the device comes with a socket specifically chosen for easy
audio/video evaluation. An application note is also available
with the evaluation board that gives full information on
operating the evaluation board.
POWER SUPPLY
The ADG2188 evaluation board can be operated with both single
and dual supplies. VDD and VSS are supplied externally by the
user. The VL supply can be applied externally, or the USB port
can power the digital circuitry.
Rev. B | Page 24 of 28
Data Sheet
ADG2188
05897-041
SCHEMATICS
Figure 36. EVAL-ADG2188EB Schematic, USB Controller Section
Rev. B | Page 25 of 28
Data Sheet
05897-042
ADG2188
Figure 37. EVAL-ADG2188EB Schematic, Chip Section
Rev. B | Page 26 of 28
Data Sheet
ADG2188
OUTLINE DIMENSIONS
DETAIL A
(JEDEC 95)
0.30
0.25
0.18
25
PIN 1
INDIC ATOR AREA OPTIONS
(SEE DETAIL A)
32
24
1
0.50
BSC
3.25
3.10 SQ
2.95
EXPOSED
PAD
17
0.50
0.40
0.30
TOP VIEW
0.80
0.75
0.70
SIDE VIEW
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
PKG-003898
8
9
16
0.25 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WHHD
02-22-2017-A
PIN 1
INDICATOR
5.10
5.00 SQ
4.90
Figure 38. 32-Lead Lead Frame Chip Scale Package [LFCSP]
5 mm x 5 mm Body and 0.75 mm Package Height
(CP-32-7)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1, 2
ADG2188BCPZ-REEL7
ADG2188YCPZ-REEL7
ADW54012Z-0REEL7
EVAL-ADG2188EBZ
1
2
Temperature
Range
−40°C to +85°C
−40°C to +125°C
−40°C to +85°C
I2C Speed
100 kHz, 400 kHz
100 kHz, 400 kHz
100 kHz, 400 kHz
Package Description
32-Lead Lead Frame Chip Scale Package [LFCSP]
32-Lead Lead Frame Chip Scale Package [LFCSP]
32-Lead Lead Frame Chip Scale Package [LFCSP]
8 x 8 Evaluation Board
Package
Option
CP-32-7
CP-32-7
CP-32-7
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The ADW54012 model is available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that this automotive model may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
Rev. B | Page 27 of 28
ADG2188
Data Sheet
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
©2006–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05897-0-7/17(B)
Rev. B | Page 28 of 28