High Voltage Latch-Up Proof,
Triple/Quad SPDT Switches
ADG5233/ADG5234
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
Latch-up proof
2.8 pF off source capacitance
9 pF off drain capacitance
0.4 pC charge injection
Low on resistance: 160 Ω typical
±9 V to ±22 V dual-supply operation
9 V to 40 V single-supply operation
48 V supply maximum ratings
Fully specified at ±15 V, ±20 V, +12 V, and +36 V
VDD to VSS analog signal range
Human body model (HBM) ESD rating
8 kV input/output port to supplies
2 kV input/output port to input/output port
8 kV all other pins
ADG5233
S1A
D1
S1B
S3B
D3
S3A
S2B
D2
S2A
LOGIC
09919-001
IN1 IN2 IN3 EN
SWITCHES SHOWN FOR
A 1 INPUT LOGIC.
Figure 1. ADG5233 TSSOP and LFCSP_WQ
ADG5234
S1A
D1
Automatic test equipment
Data acquisition
Instrumentation
Avionics
Audio and video switching
Communication systems
S4A
D4
S1B
S4B
IN1
IN4
IN2
IN3
S2B
S3B
D2
S2A
SWITCHES SHOWN FOR
A 1 INPUT LOGIC.
D3
S3A
09919-002
APPLICATIONS
Figure 2. ADG5234 TSSOP and LFCSP_WQ
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The ADG5233 and ADG5234 are monolithic industrial CMOS
analog switches comprising three independently selectable
single-pole, double throw (SPDT) switches and four independently selectable SPDT switches, respectively.
1.
All channels exhibit break-before-make switching action that
prevents momentary shorting when switching channels. An EN
input on the ADG5233 (LFCSP and TSSOP packages) is used to
enable or disable the device. When disabled, all channels are
switched off.
2.
The ultralow capacitance and charge injection of these switches
make them ideal solutions for data acquisition and sample-andhold applications, where low glitch and fast settling are required.
Fast switching speed coupled with high signal bandwidth make
these devices suitable for video signal switching.
4.
3.
5.
6.
Rev. D
Trench Isolation Guards Against Latch-Up.
A dielectric trench separates the P and N channel transistors
thereby preventing latch-up even under severe overvoltage
conditions.
Ultralow Capacitance and 0.4 pC Charge Injection.
Dual-Supply Operation.
For applications where the analog signal is bipolar, the
ADG5233/ADG5234 can be operated from dual supplies
up to ±22 V.
Single-Supply Operation.
For applications where the analog signal is unipolar, the
ADG5233/ADG5234 can be operated from a single-rail
power supply up to 40 V.
3 V Logic-Compatible Digital Inputs.
VINH = 2.0 V, VINL = 0.8 V.
No VL Logic Power Supply Required.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2011–2015 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADG5233/ADG5234
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Continuous Current per Channel, Sx or Dx ..............................7
Applications ....................................................................................... 1
Absolute Maximum Ratings ............................................................9
Functional Block Diagrams ............................................................. 1
ESD Caution...................................................................................9
General Description ......................................................................... 1
Pin Configurations and Function Descriptions ......................... 10
Product Highlights ........................................................................... 1
Typical Performance Characteristics ........................................... 12
Revision History ............................................................................... 2
Test Circuits ..................................................................................... 16
Specifications..................................................................................... 3
Terminology .................................................................................... 18
±15 V Dual Supply ....................................................................... 3
Trench Isolation .............................................................................. 19
±20 V Dual Supply ....................................................................... 4
Applications Information .............................................................. 20
12 V Single Supply ........................................................................ 5
Outline Dimensions ....................................................................... 21
36 V Single Supply ........................................................................ 6
Ordering Guide .......................................................................... 22
REVISION HISTORY
8/15—Rev. C to Rev. D
Changes to Features Section............................................................ 1
Changes to Table 1 ............................................................................ 3
Changes to Table 2 ............................................................................ 4
Changes to Table 3 ............................................................................ 5
Changes to Table 4 ............................................................................ 6
Changes to Table 7 ............................................................................ 9
Changes to Figure 20 Caption to Figure 22 Caption ................. 14
Changes to Figure 23 Caption to Figure 25 Caption ................. 15
Deleted Figure 20 and Figure 22; Renumbered Sequentially ... 15
Deleted Figure 24, Figure 26, and Figure 28 ............................... 16
Deleted Figure 30 ............................................................................ 17
6/13—Rev. A to Rev. B
Added 20-Lead LFCSP ...................................................... Universal
Updated Outline Dimensions ....................................................... 21
Changes to Ordering Guide .......................................................... 22
3/12—Rev. 0 to Rev. A
Added 16-Lead LFCSP ...................................................... Universal
Changes to Ordering Guide .......................................................... 22
7/11—Revision 0: Initial Version
12/14—Rev. B to Rev. C
Changes to Features Section and Product Highlights Section ... 1
Changes to Table 1 ............................................................................ 3
Changes to Table 2 ............................................................................ 4
Changes to Table 3 ............................................................................ 6
Changes to Table 4 ............................................................................ 7
Change to Table 7 ............................................................................. 9
Changes to Figure 7 to Figure 12 .................................................. 13
Changes to Figure 13 and Figure 14............................................. 14
Changes to Figure 19, Figure 20 Caption, and
Figure 22 Caption .......................................................................... 15
Added Figure 21 and Figure 23; Renumbered Sequentially ..... 15
Changes to Figure 24 Caption, Figure 26 Caption, and
Figure 28 Caption ........................................................................... 16
Added Figure 25, Figure 27, and Figure 28 ................................. 16
Changes Figure 30 Caption ........................................................... 17
Added Figure 31.............................................................................. 17
Changes to Figure 34 ...................................................................... 18
Rev. D | Page 2 of 22
Data Sheet
ADG5233/ADG5234
SPECIFICATIONS
±15 V DUAL SUPPLY
VDD = +15 V ± 10%, VSS = −15 V ± 10%, GND = 0 V, unless otherwise noted.
Table 1.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
On-Resistance Match Between
Channels, ∆RON
On-Resistance Flatness, RFLAT (ON)
25°C
−40°C to +85°C
−40°C to +125°C
Unit
VDD to VSS
V
Ω typ
160
VS = ±10 V, IS = −1 mA;
see Figure 28
VDD = +13.5 V, VSS = −13.5 V
VS = ±10 V, IS = −1 mA
200
3.5
250
280
Ω max
Ω typ
8
38
50
9
10
VS = ±10 V, IS = −1 mA
65
70
Ω max
Ω typ
Ω max
nA typ
VDD = +16.5 V, VSS = −16.5 V
VS = ±10 V, VD = 10 V;
see Figure 30
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
±0.02
±0.1
±0.02
±0.2
Drain Off Leakage, ID (Off )
±0.1
±0.08
±0.2
±0.2
±0.4
±0.3
±0.9
nA max
nA typ
nA max
Input High Voltage, VINH
2.0
V min
Input Low Voltage, VINL
Input Current, IINL or IINH
0.8
V max
µA typ
µA max
pF typ
Channel On Leakage, ID (On), IS (On)
Test Conditions/Comments
±0.4
nA max
nA typ
VS = ±10 V, VD = 10 V;
see Figure 30
VS = VD = ±10 V; see Figure 26
DIGITAL INPUTS
0.002
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION
3
Break-Before-Make Time Delay, tD
125
160
145
175
125
155
45
Charge Injection, QINJ
0.4
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
Off Isolation
−76
dB typ
Channel-to-Channel Crosstalk
−87
dB typ
−3 dB Bandwidth
355
MHz typ
Insertion Loss
−6.4
dB typ
CS (Off )
CD (Off )
CD (On), CS (On)
2.8
9
13
pF typ
pF typ
pF typ
tON (EN)
tOFF (EN)
190
215
210
240
170
180
25
Rev. D | Page 3 of 22
VIN = VGND or VDD
RL = 300 Ω, CL = 35 pF
VS = 10 V; see Figure 33
RL = 300 Ω, CL = 35 pF
VS = 10 V; see Figure 35
RL = 300 Ω, CL = 35 pF
VS = 10 V; see Figure 35
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 10 V; see Figure 34
VS = 0 V, RS = 0 Ω, CL = 1 nF;
see Figure 36
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 31
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
Figure 29
RL = 50 Ω, CL = 5 pF;
see Figure 32
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 32
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
ADG5233/ADG5234
Parameter
POWER REQUIREMENTS
IDD
ISS
Data Sheet
25°C
−40°C to +85°C
45
55
0.001
70
1
±9/±22
VDD/VSS
1
−40°C to +125°C
Unit
µA typ
µA max
µA typ
µA max
V min/V max
Test Conditions/Comments
VDD = +16.5 V, VSS = −16.5 V
Digital inputs = 0 V or VDD
Digital inputs = 0 V or VDD
GND = 0 V
Guaranteed by design; not subject to production test.
±20 V DUAL SUPPLY
VDD = +20 V ± 10%, VSS = −20 V ± 10%, GND = 0 V, unless otherwise noted.
Table 2.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
On-Resistance Match Between Channels,
∆RON
On-Resistance Flatness, RFLAT (ON)
25°C
−40°C to +85°C
Unit
VDD to VSS
V
Ω typ
140
230
Ω max
Ω typ
8
33
45
9
10
VS = ±15 V, IS = −1 mA
55
60
Ω max
Ω typ
Ω max
nA typ
VDD = +22 V, VSS = −22 V
VS = ±15 V, VD = 15 V;
see Figure 30
±0.1
±0.02
±0.2
Drain Off Leakage, ID (Off )
±0.1
±0.08
±0.2
Channel On Leakage, ID (On), IS (On)
±0.2
±0.3
±0.4
±0.4
tOFF (EN)
Break-Before-Make Time Delay, tD
nA max
nA typ
nA max
2.0
0.8
V min
V max
µA typ
µA max
pF typ
0.002
3
125
155
145
170
125
155
40
nA max
nA typ
±0.9
±0.1
tON (EN)
VS = ±15 V, IS = −1 mA;
see Figure 28
VDD = +18 V, VSS = −18 V
VS = ±15 V, IS = −1 mA
200
±0.02
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION
Test Conditions/Comments
160
3.5
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
−40°C to +125°C
180
200
200
220
160
170
20
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
Charge Injection, QINJ
0.7
pC typ
Off Isolation
−76
dB typ
Rev. D | Page 4 of 22
VS = ±15 V, VD = 15 V;
see Figure 30
VS = VD = ±15 V;
see Figure 26
VIN = VGND or VDD
RL = 300 Ω, CL = 35 pF
VS = 10 V; see Figure 33
RL = 300 Ω, CL = 35 pF
VS = 10 V; see Figure 35
RL = 300 Ω, CL = 35 pF
VS = 10 V; see Figure 35
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 10 V;
see Figure 34
VS = 0 V, RS = 0 Ω, CL = 1 nF;
see Figure 36
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 31
Data Sheet
Parameter
Channel-to-Channel Crosstalk
ADG5233/ADG5234
25°C
−87
−40°C to +85°C
Unit
dB typ
−3 dB Bandwidth
370
MHz typ
Insertion Loss
−5.6
dB typ
2.8
9
13
pF typ
pF typ
pF typ
CS (Off )
CD (Off )
CD (On), CS (On)
POWER REQUIREMENTS
IDD
ISS
50
70
0.001
110
1
±9/±22
VDD/VSS
1
−40°C to +125°C
μA typ
μA max
μA typ
μA max
V min/V max
Test Conditions/Comments
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 29
RL = 50 Ω, CL = 5 pF;
see Figure 32
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 32
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
VDD = +22 V, VSS = −22 V
Digital inputs = 0 V or VDD
Digital inputs = 0 V or VDD
GND = 0 V
Guaranteed by design; not subject to production test.
12 V SINGLE SUPPLY
VDD = 12 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 3.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
On-Resistance Match Between
Channels, ∆RON
On-Resistance Flatness, RFLAT (ON)
25°C
−40°C to +85°C
−40°C to +125°C
Unit
0 V to VDD
V
Ω typ
360
610
700
Ω max
Ω typ
20
170
280
21
22
VS = 0 V to 10 V, IS = −1 mA
335
370
Ω max
Ω typ
Ω max
nA typ
VDD = 13.2 V, VSS = 0 V
VS = 1 V/10 V, VD = 10 V/1 V;
see Figure 30
±0.02
±0.1
±0.02
±0.2
Drain Off Leakage, ID (Off )
±0.1
±0.08
±0.2
±0.2
±0.4
±0.3
±0.9
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
±0.4
2.0
0.8
0.002
±0.1
Digital Input Capacitance, CIN
VS = 0 V to 10 V, IS = −1 mA;
see Figure 28
VDD = 10.8 V, VSS = 0 V
VS = 0 V to 10 V, IS = −1 mA
500
5.5
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
Channel On Leakage, ID (On), IS (On)
Test Conditions/Comments
3
Rev. D | Page 5 of 22
nA max
nA typ
VS = 1 V/10 V, VD = 10 V/1 V;
see Figure 30
nA max
nA typ
nA max
VS = VD = 1 V/10 V; see Figure 26
V min
V max
μA typ
μA max
pF typ
VIN = VGND or VDD
ADG5233/ADG5234
Parameter
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION
Data Sheet
25°C
−40°C to +85°C
−40°C to +125°C
260
300
305
350
180
200
Test Conditions/Comments
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 33
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 35
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 35
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 8 V; see Figure 34
VS = 6 V, RS = 0 Ω, CL = 1 nF;
see Figure 36
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 31
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 29
RL = 50 Ω, CL = 5 pF;
see Figure 32
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 32
VS = 6 V, f = 1 MHz
VS = 6 V, f = 1 MHz
VS = 6 V, f = 1 MHz
VDD = 13.2 V
Digital inputs = 0 V or VDD
Break-Before-Make Time Delay, tD
165
215
200
245
130
165
85
Charge Injection, QINJ
0
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
Off Isolation
−76
dB typ
Channel-to-Channel Crosstalk
−87
dB typ
−3 dB Bandwidth
260
MHz typ
Insertion Loss
−9
dB typ
3
10
14
pF typ
pF typ
pF typ
tON (EN)
tOFF (EN)
45
CS (Off )
CD (Off )
CD (On), CS (On)
POWER REQUIREMENTS
IDD
40
50
65
9/40
VDD
1
Unit
µA typ
µA max
V min/V max
GND = 0 V, VSS = 0 V
Guaranteed by design; not subject to production test.
36 V SINGLE SUPPLY
VDD = 36 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 4.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
On-Resistance Match Between Channels,
∆RON
On-Resistance Flatness, RFLAT (ON)
25°C
−40°C to +85°C
−40°C to +125°C
Unit
0 V to VDD
V
Ω typ
140
Test Conditions/Comments
VS = 0 V to 30 V, IS = −1 mA;
see Figure 28
VDD = 32.4 V, VSS = 0 V
VS = 0 V to 30 V, IS = −1 mA
170
3.5
215
245
Ω max
Ω typ
8
35
50
9
10
VS = 0 V to 30 V, IS = −1 mA
60
65
Ω max
Ω typ
Ω max
nA typ
VDD = 39.6 V, VSS = 0 V
VS = 1 V/30 V, VD = 30 V/1 V;
see Figure 30
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
±0.02
±0.1
±0.02
±0.2
Drain Off Leakage, ID (Off )
±0.1
±0.08
±0.2
Channel On Leakage, ID (On), IS (On)
±0.2
±0.3
±0.4
±0.4
±0.9
Rev. D | Page 6 of 22
nA max
nA typ
nA max
nA typ
nA max
VS = 1 V/30 V, VD = 30 V/1 V;
see Figure 30
VS = VD = 1 V/30 V;
see Figure 26
Data Sheet
Parameter
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
ADG5233/ADG5234
25°C
−40°C to +85°C
−40°C to +125°C
Unit
Test Conditions/Comments
2.0
0.8
V min
V max
µA typ
µA max
pF typ
VIN = VGND or VDD
0.002
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS 1
Transition Time, tTRANSITION
3
Break-Before-Make Time Delay, tD
155
200
180
215
150
190
50
Charge Injection, QINJ
0.5
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
Off Isolation
−76
dB typ
Channel-to-Channel Crosstalk
−87
dB typ
−3 dB Bandwidth
275
MHz typ
Insertion Loss
−6.2
dB typ
2.8
9
13
pF typ
pF typ
pF typ
tON (EN)
tOFF (EN)
215
230
235
250
190
190
25
CS (Off )
CD (Off )
CD (On), CS (On)
POWER REQUIREMENTS
IDD
80
100
130
9/40
VDD
1
µA typ
µA max
V min/V max
RL = 300 Ω, CL = 35 pF
VS = 18 V; see Figure 33
RL = 300 Ω, CL = 35 pF
VS = 18 V; see Figure 35
RL = 300 Ω, CL = 35 pF
VS = 18 V; see Figure 35
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 18 V; see Figure 34
VS = 18 V, RS = 0 Ω, CL = 1 nF;
see Figure 36
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 31
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 29
RL = 50 Ω, CL = 5 pF;
see Figure 32
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 32
VS = 18 V, f = 1 MHz
VS = 18 V, f = 1 MHz
VS = 18 V, f = 1 MHz
VDD = 39.6 V
Digital inputs = 0 V or VDD
GND = 0 V, VSS = 0 V
Guaranteed by design; not subject to production test.
CONTINUOUS CURRENT PER CHANNEL, Sx OR Dx
Table 5. ADG5233
Parameter
CONTINUOUS CURRENT, Sx OR Dx
VDD = +15 V, VSS = −15 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 30.4°C/W)
VDD = +20 V, VSS = −20 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 30.4°C/W)
VDD = 12 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 30.4°C/W)
VDD = 36 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 30.4°C/W)
25°C
85°C
125°C
Unit
24
42
16
26.5
11
15
mA maximum
mA maximum
26
46
17
28
11
15
mA maximum
mA maximum
17
24
12
17
7.7
11
mA maximum
mA maximum
25
45
17
28
11
15
mA maximum
mA maximum
Rev. D | Page 7 of 22
ADG5233/ADG5234
Data Sheet
Table 6. ADG5234
Parameter
CONTINUOUS CURRENT, Sx OR Dx
VDD = +15 V, VSS = −15 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 30.4°C/W)
VDD = +20 V, VSS = −20 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 30.4°C/W)
VDD = 12 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 30.4°C/W)
VDD = 36 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 30.4°C/W)
25°C
85°C
125°C
Unit
21
38
15
24
10
14
mA maximum
mA maximum
22
41
15
26
10
15
mA maximum
mA maximum
15
22
11
16
7
11
mA maximum
mA maximum
22
40
15
26
10
15
mA maximum
mA maximum
Rev. D | Page 8 of 22
Data Sheet
ADG5233/ADG5234
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 7.
Parameter
VDD to VSS
VDD to GND
VSS to GND
Analog Inputs1
Digital Inputs1
Peak Current, Sx or Dx Pins
ADG5233
ADG5234
Continuous Current, Sx or Dx2
Temperature Range
Operating
Storage
Junction Temperature
Thermal Impedance, θJA
16-Lead TSSOP (4-Layer Board)
20-Lead TSSOP (4-Layer Board)
16-Lead LFCSP (4-Layer Board)
20-Lead LFCSP (4-Layer Board)
Reflow Soldering Peak
Temperature, Pb Free
Human Body Model (HBM) ESD
Input/Output Port to Supplies
Input/Output Port to
Input/Output Port
All Other Pins
Rating
48 V
−0.3 V to +48 V
+0.3 V to −48 V
VSS − 0.3 V to VDD + 0.3 V or
30 mA, whichever occurs
first
VSS − 0.3 V to VDD + 0.3 V or
30 mA, whichever occurs
first
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Only one absolute maximum rating can be applied at any
one time.
ESD CAUTION
76 mA (pulsed at 1 ms,
10% duty cycle maximum)
67 mA (pulsed at 1 ms,
10% duty cycle maximum)
Data + 15%
−40°C to +125°C
−65°C to +150°C
150°C
112.6°C/W
143°C/W
30.4°C/W
30.4°C/W
260(+0/−5)°C
8 kV
2 kV
8 kV
1
Overvoltages at the INx, Sx, and Dx pins are clamped by internal diodes.
Limit current to the maximum ratings given.
2
See Table 5 and Table 6.
Rev. D | Page 9 of 22
ADG5233/ADG5234
Data Sheet
D1 1
TOP VIEW
S2B 5 (Not to Scale) 12 S3B
D3
S2A 7
10
S3A
IN2 8
9
IN3
S2B 3
TOP VIEW
(Not to Scale)
D2 4
11 VSS
10 S3B
9 D3
S2A 5
11
ADG5233
09919-003
D2 6
12 EN
S1B 2
NOTES
1. EXPOSED PAD TIED TO SUBSTRATE, VSS.
Figure 3. ADG5233 TSSOP Pin Configuration
09919-004
VSS
14 GND
EN
13
ADG5233
S1B 4
13 IN1
14
IN3 7
IN1
D1 3
S3A 8
GND
15
16 S1A
16
IN2 6
VDD 1
S1A 2
15 VDD
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 4. ADG5233 LFCSP_WQ Pin Configuration
Table 8. ADG5233 Pin Function Descriptions
Pin No.
TSSOP LFCSP_WQ
1
15
2
16
3
1
4
2
5
3
6
4
7
5
8
6
9
7
10
8
11
9
12
10
13
11
Mnemonic
VDD
S1A
D1
S1B
S2B
D2
S2A
IN2
IN3
S3A
D3
S3B
VSS
14
12
EN
15
16
13
14
17
IN1
GND
EPAD
Description
Most Positive Power Supply Potential.
Source Terminal 1A. This pin can be an input or an output.
Drain Terminal 1. This pin can be an input or an output.
Source Terminal 1B. This pin can be an input or an output.
Source Terminal 2B. This pin can be an input or an output.
Drain Terminal 2. This pin can be an input or an output.
Source Terminal 2A. This pin can be an input or an output.
Logic Control Input 2.
Logic Control Input 3.
Source Terminal 3A. This pin can be an input or an output.
Drain Terminal 3. This pin can be an input or an output.
Source Terminal 3B. This pin can be an input or an output.
Most Negative Power Supply Potential. In single-supply applications, this pin can be connected to
ground.
Active Low Digital Input. When high, the device is disabled and all switches are off. When low, INx
logic inputs determine the on switches.
Logic Control Input 1.
Ground (0 V) Reference.
The exposed pad is connected internally. For increased reliability of the solder joints and maximum
thermal capability, it is recommended that the pad be soldered to the substrate, VSS.
Table 9. ADG5233 Truth Table
EN
1
0
0
1
INx
X1
0
1
SxA
Off
Off
On
SxB
Off
On
Off
X is don’t care.
Rev. D | Page 10 of 22
ADG5233/ADG5234
20 IN4
19 S4A
S1B 4
18 D4
ADG5234
VSS 5
17 S4B
D1
S1B
VSS
GND
S2B
16 VDD
TOP VIEW
GND 6 (Not to Scale) 15 NC
IN2 10
13 D3
12 S3A
11 IN3
NC = NO CONNECT. DO NOT
CONNECT TO THIS PIN.
ADG5234
TOP VIEW
15
14
13
12
11
D4
S4B
VDD
S3B
D3
D2 6
S2A 7
IN2 8
IN3 9
S3A 10
D2 8
S2A 9
14 S3B
09919-005
S2B 7
1
2
3
4
5
NOTES
1. EXPOSED PAD TIED TO SUBSTRATE, VSS.
Figure 5. ADG5234 TSSOP Pin Configuration
09919-102
D1 3
20
19
18
17
16
IN1 1
S1A 2
S1A
IN1
EN
IN4
S4A
Data Sheet
Figure 6. ADG5234 LFCSP_WQ Pin Configuration
Table 10. ADG5234 Pin Function Descriptions
TSSOP
1
2
3
4
5
Pin No.
LFCSP_WQ
19
20
1
2
3
Mnemonic
IN1
S1A
D1
S1B
VSS
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
N/A
4
5
6
7
8
9
10
11
12
N/A
13
14
15
16
17
18
GND
S2B
D2
S2A
IN2
IN3
S3A
D3
S3B
NC
VDD
S4B
D4
S4A
IN4
EN
N/A
21
EP
Description
Logic Control Input 1.
Source Terminal 1A. This pin can be an input or an output.
Drain Terminal 1. This pin can be an input or an output.
Source Terminal 1B. This pin can be an input or an output.
Most Negative Power Supply Potential. In single-supply applications, this pin can be connected to
ground.
Ground (0 V) Reference.
Source Terminal 2B. This pin can be an input or an output.
Drain Terminal 2. This pin can be an input or an output.
Source Terminal 2A. This pin can be an input or an output.
Logic Control Input 2.
Logic Control Input 3.
Source Terminal 3A. This pin can be an input or an output.
Drain Terminal 3. This pin can be an input or an output.
Source Terminal 3B. This pin can be an input or an output.
No Connect. This pin is open.
Most Positive Power Supply Potential.
Source Terminal 4B. This pin can be an input or an output.
Drain Terminal 4. This pin can be an input or an output.
Source Terminal 4A. This pin can be an input or an output.
Logic Control Input 4.
Active Low Digital Input. When high, the device is disabled and all switches are off. When low, INx
logic inputs determine the on switches.
Exposed Pad. The exposed pad is connected internally. For increased reliability of the solder joints
and maximum thermal capability, it is recommended that the pad be soldered to the substrate, VSS.
Table 11. ADG5234 Truth Table
INx
0
1
SxA
Off
On
SxB
On
Off
Rev. D | Page 11 of 22
ADG5233/ADG5234
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
160
TA = 25°C
TA = 25°C
140
140
VDD = +18V
VSS = –18V
120
100
80
VDD = +22V
VSS = –22V
VDD = +20V
VSS = –20V
60
80
40
20
20
–15
–10
–5
0
5
10
15
20
25
VS, VD (V)
Figure 7. On Resistance as a Function of VS, VD (±20 V Dual Supply)
250
0
09919-006
–20
VDD = 39.6V
VSS = 0V
VDD = 36V
VSS = 0V
60
40
0
–25
0
5
10
15
20
25
30
35
40
VS, VD (V)
Figure 10. On Resistance as a Function of VS, VD (36 V Single Supply)
250
TA = 25°C
VDD = +15V
VSS = –15V
VDD = +9V
VSS = –9V
200
ON RESISTANCE (Ω)
200
150
100
VDD = +16.5V
VSS = –16.5V
50
VDD = +15V
VSS = –15V
VDD = +13.5V
VSS = –13.5V
TA = +125°C
150
TA = +85°C
TA = +25°C
100
TA = –40°C
50
–16.5
–15.1
–13.7
–12.3
–10.9
–9.5
–8.1
–6.7
–5.3
–3.9
–2.5
–1.1
0.3
1.7
3.1
4.5
5.9
7.3
8.7
10.1
11.5
12.9
14.3
15.7
0
0
–15
09919-007
ON RESISTANCE (Ω)
100
09919-009
ON RESISTANCE (Ω)
ON RESISTANCE (Ω)
120
VDD = 32.4V
VSS = 0V
–10
–5
0
5
10
15
VS, VD (V)
09919-010
160
VS, VD (V)
Figure 11. On Resistance as a Function of VS (VD) for Different
Temperatures, ±15 V Dual Supply
Figure 8. On Resistance as a Function of VS, VD (±15 V Dual Supply)
ON RESISTANCE (Ω)
400
200
VDD = 9V
VSS = 0V
180
VDD = 10.8V
VSS = 0V
350
160
VDD = 12V
VSS = 0V
VDD = 13.2V
VSS = 0V
300
250
200
150
140
120
100
80
TA = +125°C
TA = +85°C
TA = +25°C
TA = –40°C
60
40
100
20 VDD = +20V
VSS = –20V
0
–20
–15
–10
50
VS, VD (V)
09919-008
0
0.6
1.2
1.8
2.4
3.0
3.6
4.2
4.8
5.4
6.0
6.6
7.2
7.8
8.4
9.0
9.6
10.2
10.8
11.4
12.0
12.6
13.2
0
–5
0
5
10
15
20
VS, VD (V)
Figure 9. On Resistance as a Function of VS, VD (12 V Single Supply)
Figure 12. On Resistance as a Function of VS (VD) for Different
Temperatures, ±20 V Dual Supply
Rev. D | Page 12 of 22
09919-011
450
TA = 25°C
ON RESISTANCE (Ω)
500
Data Sheet
ADG5233/ADG5234
100
500
ID (OFF) + –
450
TA = +125°C
340
300
TA = +25°C
250
200
TA = –40°C
150
100
0
IS (OFF) – +
–50
ID, IS (ON) – –
ID, IS (ON) + +
–100
–150
50
VDD = 12V
VSS = 0V
0
4
6
8
10
12
VS, VD (V)
0
25
50
75
100
125
TEMPERATURE (°C)
Figure 13. On Resistance as a Function of VS (VD) for Different
Temperatures, 12 V Single Supply
250
VDD = +20V
VSS = –20V
VBIAS = +15V/–15V
–200
2
09919-012
0
IS (OFF) + –
ID (OFF) – +
09919-015
LEAKAGE CURRENT (pA)
ON RESISTANCE (Ω)
50
TA = +85°C
400
Figure 16. Leakage Currents as a Function of Temperature,
±20 V Dual Supply
100
VDD = 36V
VSS = 0V
IS (OFF) + – IS (OFF) – +
0
TA = +125°C
100
TA = +85°C
TA = +25°C
TA = –40°C
–100
ID, IS (ON) + +
–200
ID (OFF) – +
–300
–400
–500
50
0
5
10
15
20
25
30
35
VS, VD (V)
09919-013
0
–600 VDD = 12V
VSS = 0V
VBIAS = 1V/10V
–700
0
25
50
75
100
125
Figure 17. Leakage Currents as a Function of Temperature,
12 V Single Supply
200
IS (OFF) + –
IS (OFF) – +
ID (OFF) – +
0
ID, IS (ON) + +
IS (OFF) + –
ID, IS (ON) + +
–50
ID (OFF) + –
–100
ID (OFF) – +
–150
ID, IS (ON) – –
–200
0
25
ID (OFF) + –
–400
–600
–800
VDD = +15V
VSS = –15V
VBIAS = +10V/–10V
–250
IS (OFF) – +
–200
50
75
TEMPERATURE (°C)
100
125
VDD = 36V
VSS = 0V
VBIAS = 1V/30V
–1000
0
25
ID, IS (ON) – –
50
75
100
125
TEMPERATURE (°C)
Figure 15. Leakage Currents as a Function of Temperature, ±15 V Dual
Supply
Figure 18. Leakage Currents as a Function of Temperature,
36 V Single Supply
Rev. D | Page 13 of 22
09919-017
LEAKAGE CURRENT (pA)
0
09919-014
LEAKAGE CURRENT (pA)
ID (OFF) + –
TEMPERATURE (°C)
Figure 14. On Resistance as a Function of VS (VD) for Different
Temperatures, 36 V Single Supply
50
ID, IS (ON) – –
09919-016
150
LEAKAGE CURRENT (pA)
ON RESISTANCE (Ω)
200
ADG5233/ADG5234
VDD
VDD
VDD
VDD
4
–40
–60
–80
–100
= +20V,
= +15V,
= +12V,
= +36V,
VSS
VSS
VSS
VSS
TA = 25°C
SOURCE TO DRAIN
= –20V
= –15V
= 0V
= 0V
3
2
1
0
100k
1M
10M
100M
1G
FREQUENCY (Hz)
–1
–20
09919-018
–120
10k
Figure 19. Off Isolation vs. Frequency, ±15 V Dual Supply
0
–10
10
VS (V)
20
09919-020
OFF ISOLATION (dB)
–20
5
TA = 25°C
VDD = +15V
VSS = –15V
CHARGE INJECTION (pC)
0
Data Sheet
30
Figure 21. Charge Injection vs. Source Voltage, Source to Drain
0
0
TA = 25°C
VDD = +15V
–20 VSS = –15V
–20
TA = 25°C
VDD = +15V
VSS = –15V
ACPSSR (dB)
–40
–60
BETWEEN SxA AND SxB
–80
NO DECOUPLING
CAPACITORS
–60
–80
–100
BETWEEN S1x AND S2x
–120
–100
–140
10k
100k
1M
10M
100M
FREQUENCY (Hz)
1G
–120
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 22. ACPSRR vs. Frequency, ±15 V Dual Supply
Figure 20. Crosstalk vs. Frequency, ±15 V Dual Supply
Rev. D | Page 14 of 22
10M
09919-021
DECOUPLING
CAPACITORS
09919-019
CROSSTALK (dB)
–40
Data Sheet
0
TA = 25°C
20 VDD = +15V
VSS = –15V
TA = 25°C
VDD = +15V
VSS = –15V
CAPACITANCE (pF)
ATTENUATION (dB)
–2
ADG5233/ADG5234
–4
–6
–8
15
SOURCE/DRAIN ON
10
DRAIN OFF
5
1M
10M
100M
1G
FREQUENCY (Hz)
0
–15
09919-023
–12
100k
250
VDD = +36V, V SS = 0V
VDD = +20V, V SS = –20V
VDD = +15V, V SS = –15V
50
0
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
120
09919-024
TIME (ns)
VDD = +12V, V SS = 0V
100
0
5
10
15
Figure 25. Capacitance vs. Source Voltage, ±15 V Dual Supply
300
150
–5
VS (V)
Figure 23. Bandwidth
200
–10
Figure 24. tTRANSITION Times vs. Temperature
Rev. D | Page 15 of 22
09919-025
SOURCE OFF
–10
ADG5233/ADG5234
Data Sheet
TEST CIRCUITS
ID
D
S2
IS (OFF)
(ON)
VD
VD
Figure 30. Off Leakage
VDD
S1
I
D D
S2
VSS
0.1µF
0.1µF
(ON)
A
VDD
IS (OFF)
VD
NC
09919-127
VS
NETWORK
ANALYZER
VSS
SxA
IN
SxB
50Ω
50Ω
VS
Figure 27. On and Off Leakage On and Off Leakage (ADG5234 TSSOP)
Dx
VIN
D
OFF ISOLATION = 20 log
09919-128
IDS
VS
RON = V ÷ IDS
VDD
VSS
NETWORK
ANALYZER
VOUT
VDD
VSS
0.1µF
0.1µF
0.1µF
0.1µF
VOUT
VS
Figure 31. Off Isolation
Figure 28. On Resistance
VDD
VDD
VSS
NETWORK
ANALYZER
VSS
NC
SxA
RL
50Ω
Dx
SxB
INx
R
50Ω
SxA
SxB
50Ω
50Ω
VS
Dx
INx
VIN
GND
CHANNEL-TO-CHANNEL CROSSTALK = 20 log
VOUT
VS
RL
50Ω
GND
09919-029
VS
VOUT
09919-030
GND
V
S
RL
50Ω
Figure 29. Channel-to-Channel Crosstalk
Rev. D | Page 16 of 22
INSERTION LOSS = 20 log
VOUT
VOUT WITH SWITCH
VOUT WITHOUT SWITCH
Figure 32. Bandwidth
09919-033
A
A
VS
Figure 26. On Leakage
NC
D
SB
A
09919-126
VS
ID (OFF)
SA
A
A
09919-130
S1
NC
Data Sheet
ADG5233/ADG5234
0.1µF
VDD
VSS
VDD
VIN
50%
50%
VIN
50%
50%
VSS
SxB
VS
0.1µF
Dx
SxA
VOUT
RL
300Ω
INx
CL
35pF
90%
VOUT
90%
tON
TRANSITION
tOFF
TRANSITION
tD
tD
09919-100
GND
VIN
Figure 33. Switching Timing
VDD
VSS
0.1µF
VDD
VSS
SxB
VS
VIN
Dx
SxA
VOUT
RL
300Ω
INx
CL
35pF
VOUT 80%
GND
VIN
09919-035
0.1µF
Figure 34. Break-Before-Make Delay, tD
3V
ENABLE
DRIVE (VIN)
50%
50%
VDD
VSS
VDD
VSS
INx
SxA
VS
SxB
0V
tON (EN)
tOFF (EN)
OUTPUT
0.9VOUT
Dx
EN
OUTPUT
VIN
50Ω
300Ω
0.1VOUT
Figure 35. Enable Delay, tON (EN), tOFF (EN)
VDD
VSS
0.1µF
0.1µF
VIN (NORMALLY
CLOSED SWITCH)
VDD
VSS
SxB
Dx
INx
VIN
NC
SxA
CL
1nF
VOUT
ON
OFF
VIN (NORMALLY
OPEN SWITCH)
VOUT
∆VOUT
GND
QINJ = CL × ∆VOUT
09919-037
VS
35pF
09919-101
GND
Figure 36. Charge Injection
Rev. D | Page 17 of 22
ADG5233/ADG5234
Data Sheet
TERMINOLOGY
IDD
IDD represents the positive supply current.
CIN
CIN represents digital input capacitance.
ISS
ISS represents the negative supply current.
tON (EN)
tON (EN) represents the delay time between the 50% and 90%
points of the digital input and switch on condition.
VD, VS
VD and VS represent the analog voltage on Terminal Dx and
Terminal Sx, respectively.
tOFF (EN)
tOFF (EN) represents the delay time between the 50% and 90%
points of the digital input and switch off condition.
RON
RON is the ohmic resistance between Terminal Dx and
Terminal Sx.
tTRANSITION
Delay time between the 50% and 90% points of the digital
inputs and the switch on condition when switching from one
address state to another.
∆RON
∆RON represents the difference between the RON of any two
channels.
RFLAT (ON)
The difference between the maximum and minimum value of
on resistance as measured over the specified analog signal range
is represented by RFLAT (ON).
IS (Off)
IS (Off) is the source leakage current with the switch off.
tD
tD represents the off time measured between the 80% point of
both switches when switching from one address state to another.
Off Isolation
Off isolation is a measure of unwanted signal coupling through
an off channel.
Charge Injection
Charge injection is a measure of the glitch impulse transferred
from the digital input to the analog output during switching.
ID (Off)
ID (Off) is the drain leakage current with the switch off.
ID (On), IS (On)
ID (On) and IS (On) represent the channel leakage currents with
the switch on.
VINL
VINL is the maximum input voltage for Logic 0.
Crosstalk
Crosstalk is a measure of unwanted signal that is coupled
through from one channel to another as a result of parasitic
capacitance.
Bandwidth
Bandwidth is the frequency at which the output is attenuated
by 3 dB.
VINH
VINH is the minimum input voltage for Logic 1.
On Response
On response is the frequency response of the on switch.
IINL, IINH
IINL and IINH represent the low and high input currents of the
digital inputs.
CD (Off)
CD (Off) represents the off switch drain capacitance, which is
measured with reference to ground.
CS (Off)
CS (Off) represents the off switch source capacitance, which is
measured with reference to ground.
AC Power Supply Rejection Ratio (ACPSRR)
ACPSRR is a measure of the ability of a part to avoid coupling
noise and spurious signals that appear on the supply voltage pin
to the output of the switch. The dc voltage on the device is
modulated by a sine wave of 0.62 V p-p. The ratio of the
amplitude of the signal on the output to the amplitude of the
modulation is the ACPSRR.
CD (On), CS (On)
CD (On) and CS (On) represent on switch capacitances, which
are measured with reference to ground.
Rev. D | Page 18 of 22
Data Sheet
ADG5233/ADG5234
TRENCH ISOLATION
In the ADG5233/ADG5234, an insulating oxide layer (trench)
is placed between the NMOS and the PMOS transistors of each
CMOS switch. Parasitic junctions, which occur between the
transistors in junction isolated switches, are eliminated, and the
result is a completely latch-up proof switch.
PMOS
P WELL
N WELL
TRENCH
BURIED OXIDE LAYER
HANDLE WAFER
Figure 37. Trench Isolation
Rev. D | Page 19 of 22
09919-038
In junction isolation, the N and P wells of the PMOS and
NMOS transistors form a diode that is reverse-biased under
normal operation. However, during overvoltage conditions, this
diode can become forward-biased. A silicon controlled rectifier
(SCR) type circuit is formed by the two transistors causing a
significant amplification of the current that, in turn, leads to
latch-up. With trench isolation, this diode is removed, and the
result is a latch-up proof switch.
NMOS
ADG5233/ADG5234
Data Sheet
APPLICATIONS INFORMATION
The low capacitance latch-up immune family of switches and
multiplexers provide a robust solution for instrumentation,
industrial, automotive, aerospace, and other harsh environments
that are prone to latch-up, which is an undesirable high current
state that can lead to device failure and persists until the power
supply is turned off.
The ADG5233/ADG5234 high voltage switches allow singlesupply operation from 9 V to 40 V and dual supply operation
from ±9 V to ±22 V.
Rev. D | Page 20 of 22
Data Sheet
ADG5233/ADG5234
OUTLINE DIMENSIONS
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.30
0.19
0.65
BSC
COPLANARITY
0.10
0.75
0.60
0.45
8°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 38. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
PIN 1
INDICATOR
4.10
4.00 SQ
3.90
0.35
0.30
0.25
0.65
BSC
16
13
PIN 1
INDICATOR
12
1
EXPOSED
PAD
4
2.70
2.60 SQ
2.50
9
0.80
0.75
0.70
SEATING
PLANE
0.45
0.40
0.35
8
5
0.20 MIN
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WGGC.
Figure 39. 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
4 mm × 4 mm Body, Very Very Thin Quad
(CP-16-17)
Dimensions shown in millimeters
Rev. D | Page 21 of 22
08-16-2010-C
TOP VIEW
ADG5233/ADG5234
Data Sheet
6.60
6.50
6.40
20
11
4.50
4.40
4.30
6.40 BSC
1
10
PIN 1
0.65
BSC
1.20 MAX
0.15
0.05
0.30
0.19
COPLANARITY
0.10
0.20
0.09
0.75
0.60
0.45
8°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153-AC
Figure 40. 20-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-20)
Dimensions shown in millimeters
0.30
0.25
0.18
0.50
BSC
PIN 1
INDICATOR
20
16
15
1
EXPOSED
PAD
2.75
2.60 SQ
2.35
11
TOP VIEW
0.80
0.75
0.70
0.50
0.40
0.30
5
10
0.25 MIN
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
6
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WGGD.
020509-B
PIN 1
INDICATOR
4.10
4.00 SQ
3.90
Figure 41. 20-LEAD LEAD FRAME CHIP SCALE PACKAGE [LFCSP_WQ]
4 mm × 4 mm BODY, VERY VERY THIN QUAD
(CP-20-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
ADG5233BRUZ
ADG5233BRUZ-RL7
ADG5233BCPZ-RL7
ADG5234BRUZ
ADG5234BRUZ-RL7
ADG5234BCPZ-RL7
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Description
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
Z = RoHS Compliant Part.
©2011–2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09919-0-8/15(D)
Rev. D | Page 22 of 22
EN Pin
Yes
Yes
Yes
No
No
Yes
Package Option
RU-16
RU-16
CP-16-17
RU-20
RU-20
CP-20-8