ADIS16135BMLZ

The World Leader in High Performance Signal Processing Solutions iSensor ® ADIS16135 Evaluation Tool Overview Mark Looney iSensor® Application Engineer July 2011 iSensor® The Simple Solution for Sensor Integration PC-Based Evaluation  The ADISUSBZ provides PC-based demonstration and basic evaluation support for the ADIS16135BMLZ.  This system provides a simple USB interface, along with a simple graphical user interface (GUI) package, for evaluating most of the ADIS16135 functions and performance.  This system is most useful for basic data collection and performance validation.  This is not a real-time development system. No SDK available.  Part number for ordering: (1) ADIS16135BMLZ, (1) ADISUSBZ ADIS16135BMLZ ADISUSBZ 2 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Software Installation The ADIS16135 demonstration software can be found at www.analog.com/ADIS16135 1. Click on “Evaluation Software Downloads” 2. Click on 135ES.zip and save it to a temporary directory 3. Open it and double click on setup.exe. 4 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Software Installation Installation Steps (continued) 4. Click OK on next screen 5. Click here to start installation 5 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Software Installation Installation Steps (continued) 6. Click Continue 7. If this message comes up, click on No 8. Click OK 6 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Software Installation Installation Steps (continued) 9. Open the newly created directory and double-click onto GIVEIO.EXE 10. Click Install, then I agree 7 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Software Installation Installation Steps (continued) 11. Click Yes 12. Giveio Driver complete, click OK 8 iSensor® The Simple Solution for Sensor Integration ADIS16135BMLZ Installation on ADISEVALUSBZ-135 Installation Steps (continued) 13. Install ADIS16135BMLZ on ADISEVALUSBZ 14. Remove ribbon cable and screws 1. Secure with 2x18mm screws 2. Attach 135/PCBZ to J4 Connector 15. Carefully insert the ADIS16135BMLZ into the J4 connector 16. Secure part with 2x18mm screws 3. Verify JP1 set to +5V 4. Hook USB cable up 9 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Software Installation Installation Steps (continued) 17. USB Driver screen will pop-up Click Next to start this process 18. Then click on Continue Anyway This process will repeat for a second driver file. Just follow the instructions and allow it to go through one more time. After completing this, the devices is ready for test. 10 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Tips—Verify USB Driver #1 Click here to access setup #2 Click OK to verify 11 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Tips— Initial Start up #3 Click Read to see if Gyro Out is close to “0” when board is laying flat on a table 12 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Tips—AUTO-Null While the part is flat on the table top click on Run button. When complete, click on Update, then Flash Memory Update. Select Configuration and Calibration 13 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Tips— Gyro 1. Watch the Gyro Out response on screen. 1 Observe Gyro Out while rotating board back and forth on table top 14 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Tips— Alarms?? Select Configuration and Alarms from the drop down menu 15 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Tips— Alarm Set up 1. Set Alarm 1 source for Gyro Out. 1 2. Set the Trigger level to 50 and Greater Than 2 3. Click the Update button to accept changes 4. Click on Close Window to return to the main screen 3 4 16 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Tips— Alarms Continued 5. Alarm 1 is set when the Gyro level is above 50 6. The Plot Scale can be changed for a more accurate reading by moving the slider 5 Position part as shown and observe output and axis Readings 6 17 iSensor® The Simple Solution for Sensor Integration ADIS16135 Demonstration Tips— Collect Data 1. Select Datalog on the main screen 1 2. File Setup- enter # of samples delay and # of files 2 3 4 3. Data Selection- Choose the output data you want 4. File Information- Enter the file name and # of files 5. Start Datalog- Click the button to begin data processing a. File is output to program file folder created during installation 5 18  CONTACTS:  APPLICATIONS  MARKETING: ENGINEER: Mark Looney, 1-336-605-4139 Bob Scannell, 1-336-605-4031 Analog Devices, Inc. 7910 Triad Center Drive Greensboro, NC 27409 EMAIL: mark.looney@analog.com 19