ADL5357-EVALZ1

500 MHz to 1700 MHz Balanced Mixer, LO Buffer, IF Amplifier, and RF Balun ADL5357 FEATURES RF frequency range of 500 MHz to 1700 MHz IF frequency range of 30 MHz to 450 MHz Power conversion gain: 8.6 dB SSB noise figure of 9.1 dB SSB noise figure with 5 dBm blocker of 19.5 dB Input IP3 of 26.6 dBm Input P1dB of 10.2 dBm Typical LO drive of 0 dBm Single-ended, 50 Ω RF and LO input ports High isolation SPDT LO input switch Single-supply operation: 3.3 V to 5 V Exposed paddle 5 mm × 5 mm, 20-lead LFCSP 1500 V HBM/500 V FICDM ESD performance FUNCTIONAL BLOCK DIAGRAM IFGM 20 IFOP 19 IFON 18 PWDN 17 LEXT 16 ADL5357 VPIF 1 15 LOI2 RFIN 2 14 VPSW RFCT 3 BIAS GENERATOR COMM 4 13 VGS1 12 VGS0 APPLICATIONS Cellular base station receivers Transmit observation receivers Radio link downconverters COMM 5 6 7 8 9 10 11 LOI1 NC = NO CONNECT Figure 1. GENERAL DESCRIPTION The ADL5357 uses a highly linear, doubly balanced passive mixer core along with integrated RF and LO balancing circuitry to allow for single-ended operation. The ADL5357 incorporates an RF balun, allowing for optimal performance over a 500 MHz to 1700 MHz RF input frequency range using high-side LO injection for RF frequencies from 500 MHz to 1200 MHz and low-side injection for frequencies from 900 MHz to 1700 MHz. The balanced passive mixer arrangement provides good LO-to-RF leakage, typically better than −46 dBm, and excellent intermodulation performance. The balanced mixer core also provides extremely high input linearity, allowing the device to be used in demanding cellular applications where in-band blocking signals may otherwise result in the degradation of dynamic performance. A high linearity IF buffer amplifier follows the passive mixer core to yield a typical power conversion gain of 8.6 dB and can be used with a wide range of output impedances. The ADL5357 provides two switched LO paths that can be used in TDD applications where it is desirable to rapidly switch between two local oscillators. LO current can be externally set using a resistor to minimize dc current commensurate with the desired level of performance. For low voltage applications, the ADL5357 is capable of operation at voltages down to 3.3 V with substantially reduced current. Under low voltage operation, an additional logic pin is provided to power down (20 dB over a limited bandwidth 500 Differential impedance, f = 200 MHz Externally generated 30 3.3 −6 240||0.4 5.0 0 12 50 450 5.5 +10 Min Typ 19 50 1700 Max Unit dB Ω MHz Ω||pF MHz V dBm dB Ω MHz V V V ns ns μA μA 730 1.0 1670 0.4 1.4 Device enabled, IF output to 90% of its final level Device disabled, supply current < 5 mA Device enabled Device disabled 160 220 0.0 70 1 2 Apply the supply voltage from the external circuit through the choke inductors. The PWDN function is intended for use with VPOS ≤ 3.6 V only. Rev. 0 | Page 3 of 24 ADL5357 5 V PERFORMANCE VPOS = 5 V, IS = 190 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless otherwise noted. Table 3. Parameter DYNAMIC PERFORMANCE Power Conversion Gain Voltage Conversion Gain SSB Noise Figure SSB Noise Figure Under Blocking Input Third-Order Intercept (IIP3) Input Second-Order Intercept (IIP2) Input 1 dB Compression Point (IP1dB) LO-to-IF Leakage LO-to-RF Leakage RF-to-IF Isolation IF/2 Spurious IF/3 Spurious POWER SUPPLY Positive Supply Voltage Quiescent Current Total Quiescent Current Conditions Including 4:1 IF port transformer and PCB loss ZSOURCE = 50 Ω, differential ZLOAD = 200 Ω differential 5 dBm blocker present ±10 MHz from wanted RF input, LO source filtered fRF1 = 899.5 MHz, fRF2 = 900.5 MHz, fLO = 1103 MHz, each RF tone at −10 dBm fRF1 = 950 MHz, fRF2 = 900 MHz, fLO = 1103 MHz, each RF tone at −10 dBm Unfiltered IF output Min 7 Typ 8.6 14.9 9.1 19.5 26.6 62.8 10.2 −7 −46.7 −35 −69.2 −83.4 4.5 LO supply, resistor programmable IF supply, resistor programmable VPOS = 5 V 5 100 90 190 5.5 Max 9.5 Unit dB dB dB dB dBm dBm dBm dBm dBm dBc dBc dBc V mA mA mA 22 −10 dBm input power −10 dBm input power 3.3 V PERFORMANCE VPOS = 3.3 V, IS = 125 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, R9 = 226 Ω, R14 = 604 Ω, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless otherwise noted. Table 4. Parameter DYNAMIC PERFORMANCE Power Conversion Gain Voltage Conversion Gain SSB Noise Figure Input Third-Order Intercept (IIP3) Input Second-Order Intercept (IIP2) Input 1 dB Compression Point (IP1dB) POWER INTERFACE Supply Voltage Quiescent Current Power-Down Current Conditions Including 4:1 IF port transformer and PCB loss ZSOURCE = 50 Ω, differential ZLOAD = 200 Ω differential fRF1 = 899.5 MHz, fRF2 = 900.5 MHz, fLO = 1103 MHz, each RF tone at −10 dBm fRF1 = 950 MHz, fRF2 = 900 MHz, fLO = 1103 MHz, each RF tone at −10 dBm Min Typ 8.8 15.1 9.0 21.4 55.7 7.1 3.0 Resistor programmable Device disabled 3.3 125 150 3.6 Max Unit dB dB dB dBm dBm dBm V mA μA Rev. 0 | Page 4 of 24 ADL5357 ABSOLUTE MAXIMUM RATINGS Table 5. Parameter Supply Voltage, VPOS RF Input Level LO Input Level IFOP, IFON Bias Voltage VGS0, VGS1, LOSW, PWDN Internal Power Dissipation θJA Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Lead Temperature Range (Soldering, 60 sec) Rating 5.5 V 20 dBm 13 dBm 6.0 V 5.5 V 1.2 W 25°C/W 150°C −40°C to +85°C −65°C to +150°C 260°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. 0 | Page 5 of 24 ADL5357 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS IFGM IFOP IFON PWDN LEXT VPIF RFIN RFCT COMM COMM 1 2 3 4 5 20 19 18 17 16 PIN 1 INDICATOR ADL5357 TOP VIEW (Not to Scale) 15 LOI2 14 VPSW 13 VGS1 12 VGS0 11 LOI1 NOTES 1. NC = NO CONNECT. 2. EXPOSED PAD. MUST BE SOLDERED TO GROUND. VLO3 6 LGM3 7 VLO2 8 LOSW 9 NC 10 Figure 2. Pin Configuration Table 6. Pin Function Descriptions Pin No. 1 2 3 4, 5 6, 8 7 9 10 11, 15 12, 13 14 16 17 18, 19 20 Mnemonic VPIF RFIN RFCT COMM VLO3, VLO2 LGM3 LOSW NC LOI1, LOI2 VGS0, VGS1 VPSW LEXT PWDN IFON, IFOP IFGM EPAD (EP) Description Positive Supply Voltage for IF Amplifier. RF Input. Must be ac-coupled. RF Balun Center Tap (AC Ground). Device Common (DC Ground). Positive Supply Voltages for LO Amplifier. LO Amplifier Bias Control. LO Switch. LOI1 selected for 0 V, and LOI2 selected for 3 V. No Connect. LO Inputs. Must be ac-coupled. Mixer Gate Bias Controls. 3 V logic. Ground these pins for nominal setting. Positive Supply Voltage for LO Switch. IF Return. This pin must be grounded. Power Down. Connect this pin to ground for normal operation and connect this pin to 3.0 V for disable mode. Differential IF Outputs (Open Collectors). Each requires an external dc bias. IF Amplifier Bias Control. Exposed pad. Must be soldered to ground. Rev. 0 | Page 6 of 24 08081-002 ADL5357 TYPICAL PERFORMANCE CHARACTERISTICS 5 V PERFORMANCE VPOS = 5 V, IS = 190 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, R9 = 1.1 kΩ, R14 = 910 Ω, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless otherwise noted. 220 210 80 70 TA = –40°C 60 TA = +25°C SUPPLY CURRENT (mA) 200 TA = –40°C INPUT IP2 (dBm) 50 40 30 20 10 0 700 TA = +85°C 190 180 170 160 150 700 TA = +85°C TA = +25°C 08081-034 750 800 850 900 950 1000 1050 1100 1150 1200 750 800 850 900 950 1000 1050 1100 1150 1200 RF FREQUENCY (MHz) RF FREQUENCY (MHz) Figure 3. Supply Current vs. RF Frequency 12 14 13 12 Figure 6. Input IP2 vs. RF Frequency 10 TA = –40°C TA = +25°C CONVERSION GAIN (dB) INPUT P1dB (dBm) 8 TA = +85°C 11 10 9 8 TA = +25°C TA = +85°C 6 TA = –40°C 4 2 7 6 700 750 800 850 900 950 1000 1050 1100 1150 1200 08081-015 750 800 850 900 950 1000 1050 1100 1150 1200 RF FREQUENCY (MHz) RF FREQUENCY (MHz) Figure 4. Power Conversion Gain vs. RF Frequency 35 30 25 TA = –40°C TA = +25°C Figure 7. Input P1dB vs. RF Frequency 20 18 16 SSB NOISE FIGURE (dB) INPUT IP3 (dBm) TA = +85°C 14 12 10 8 6 4 TA = +85°C TA = +25°C 20 15 10 5 TA = –40°C 2 750 800 850 900 950 1000 1050 1100 1150 1200 08081-027 750 800 850 900 950 1000 1050 1100 1150 1200 RF FREQUENCY (MHz) 08081-021 0 700 0 700 RF FREQUENCY (MHz) Figure 5. Input IP3 vs. RF Frequency Figure 8. SSB Noise Figure vs. RF Frequency Rev. 0 | Page 7 of 24 08081-024 0 700 08081-019 ADL5357 250 VPOS = 5.25V 80 70 60 INPUT IP2 (dBm) VPOS = 4.75V VPOS = 5V VPOS = 5.0V VPOS = 5.25V 200 SUPPLY CURRENT (mA) VPOS = 4.75V 150 50 40 30 20 100 50 10 0 –40 –20 0 20 40 60 80 08081-035 –20 0 20 40 60 80 TEMPERATURE (°C) TEMPERATURE (°C) Figure 9. Supply Current vs. Temperature 10 14 VPOS = 4.75V VPOS = 5.0V VPOS = 5.25V 13 12 Figure 12. Input IP2 vs. Temperature 9 CONVERSION GAIN (dB) 8 INPUT P1dB (dBm) 11 10 9 8 7 6 5 VPOS = 4.75V VPOS = 5.0V VPOS = 5.25V 7 6 5 –20 0 20 40 60 80 08081-046 –20 0 20 40 60 80 TEMPERATURE (°C) TEMPERATURE (°C) Figure 10. Power Conversion Gain vs. Temperature 35 33 31 29 INPUT IP3 (dBm) 11 12 Figure 13. Input P1dB vs. Temperature VPOS = 5.0V VPOS = 5.25V VPOS = 4.75V SSB NOISE FIGURE (dB) VPOS = 5.0V 10 VPOS = 5.25V 27 25 23 21 19 17 –20 0 20 40 9 VPOS = 4.75V 8 7 60 80 08081-048 –20 0 20 40 60 80 TEMPERATURE (°C) TEMPERATURE (°C) Figure 11. Input IP3 vs. Temperature Figure 14. SSB Noise Figure vs. Temperature Rev. 0 | Page 8 of 24 08081-028 15 –40 6 –40 08081-049 4 –40 4 –40 08081-047 0 –40 ADL5357 220 210 SUPPLY CURRENT (mA) 80 70 TA = –40°C TA = +25°C 200 INPUT IP2 (dBm) 60 TA = –40°C 50 40 30 20 10 0 TA = +85°C 190 180 TA = +25°C TA = +85°C 170 160 150 30 08081-031 80 130 180 230 280 330 380 430 30 80 130 180 230 280 330 380 430 IF FREQUENCY (MHz) IF FREQUENCY (MHz) Figure 15. Supply Current vs. IF Frequency 12 12 Figure 18. Input IP2 vs. IF Frequency 10 CONVERSION GAIN (dB) TA = –40°C TA = +25°C 10 TA = +85°C TA = –40°C TA = +25°C TA = +85°C 6 INPUT P1dB (dBm) 8 8 6 4 4 2 2 08081-013 80 130 180 230 280 330 380 430 80 130 180 230 280 330 380 430 IF FREQUENCY (MHz) IF FREQUENCY (MHz) Figure 16. Power Conversion Gain vs. IF Frequency 35 30 25 TA = –40°C TA = +25°C Figure 19. Input P1dB vs. IF Frequency 15 14 13 SSB NOISE FIGURE (dB) TA = +85°C 12 11 10 9 8 7 INPUT IP3 (dBm) 20 15 10 5 0 30 6 08081-020 80 130 180 230 280 330 380 430 80 130 180 230 280 330 380 430 IF FREQUENCY (MHz) IF FREQUENCY (MHz) Figure 17. Input IP3 vs. IF Frequency Figure 20. SSB Noise Figure vs. IF Frequency Rev. 0 | Page 9 of 24 08081-011 5 30 08081-022 0 30 0 30 08081-017 ADL5357 12 12 TA = +85°C 10 TA = –40°C TA = +25°C 10 TA = –40°C CONVERSION GAIN (dB) TA = +25°C TA = +85°C 6 INPUT P1dB (dBm) 2 4 6 8 10 08081-014 8 8 6 4 4 2 2 –4 –2 0 2 4 6 8 10 LO POWER LEVEL (dBm) LO POWER (dBm) Figure 21. Power Conversion Gain vs. LO Power 30 TA = –40°C –10 0 Figure 24. Input P1dB vs. LO Power 25 TA = +85°C TA = +25°C –20 INPUT IP3 (dBm) 20 IF/2 SPURIOUS (dBc) –30 –40 –50 –60 –70 TA = –40°C TA = +85°C 750 800 850 900 950 1000 1050 1100 1150 1200 08081-007 08081-008 15 10 TA = +25°C 5 –80 6 4 2 0 2 4 6 8 10 LO POWER LEVEL (dBm) 08081-016 0 –90 700 RF FREQUENCY (MHz) Figure 22. Input IP3 vs. LO Power 80 70 60 50 40 30 20 TA = –40°C TA = +25°C Figure 25. IF/2 Spurious vs. RF Frequency 0 –10 –20 IF/3 SPURIOUS (dBc) TA = +85°C –30 –40 –50 –60 –70 –80 TA = +25°C TA = –40°C 750 800 850 900 950 INPUT IP2 (dBm) 10 0 –6 –90 –4 –2 0 2 4 6 8 10 08081-018 –100 700 TA = +85°C 1000 1050 1100 1150 1200 LO POWER (dBm) RF FREQUENCY (MHz) Figure 23. Input IP2 vs. LO Power Figure 26. IF/3 Spurious vs. RF Frequency Rev. 0 | Page 10 of 24 08081-023 0 –6 –4 –2 0 0 –6 ADL5357 100 MEAN: 8.59 SD: 0.14% 500 10 DISTRIBUTION PERCENTAGE (%) 80 400 8 60 300 6 40 200 4 20 100 2 08081-044 8.4 8.5 8.6 8.7 8.8 8.9 80 130 180 230 280 330 380 430 CONVERSION GAIN (dB) IF FREQUENCY (MHz) Figure 27. Power Conversion Gain Distribution 100 Figure 30. IF Port Return Loss 0 5 MEAN: 26.57 SD: 0.39% DISTRIBUTION PERCENTAGE (%) 80 RF RETURN LOSS (dB) 10 15 20 25 30 35 60 40 20 INPUT IP3 (dBm) 08081-043 750 800 850 900 950 1000 1050 1100 1150 1200 RF FREQUENCY (MHz) Figure 28. Input IP3 Distribution 100 0 Figure 31. RF Port Return Loss, Fixed IF MEAN: 10.22 SD: 0.50% DISTRIBUTION PERCENTAGE (%) 80 5 LO RETURN LOSS (dB) 10 SELECTED 15 UNSELECTED 20 60 40 20 25 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 LO FREQUENCY (MHz) INPUT P1dB (dBm) Figure 29. Input P1dB Distribution Figure 32. LO Return Loss, Selected and Unselected Rev. 0 | Page 11 of 24 08081-038 9.6 9.9 10.2 10.5 10.8 08081-045 0 30 900 08081-029 0 24 25 26 27 28 29 40 700 08081-050 0 8.3 0 30 0 CAPACITANCE (pF) RESISTANCE (Ω) ADL5357 70 0 65 –10 TA = +25°C TA = +85°C TA = –40°C LO SWITCH ISOLATION (dB) 60 LO-TO-RF LEAKAGE (dBm) –20 55 –30 TA = +85°C –40 TA = –40°C 50 45 –50 TA = +25°C 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 LO FREQUENCY (MHz) 08081-026 08081-040 08081-039 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 LO FREQUENCY (MHz) 08081-041 40 900 –60 900 Figure 33. LO Switch Isolation vs. LO Frequency 0 –5 Figure 36. LO-to-RF Leakage vs. LO Frequency 0 –5 –10 2LO LEAKAGE (dBm) RF-TO-IF ISOLATION (dBc) –10 –15 –20 –25 –30 –35 –40 –45 700 TA = +85°C TA = –40°C TA = +25°C –15 –20 2LO TO RF 2LO TO IF –25 –30 –35 –40 –45 900 750 800 850 900 950 1000 1050 1100 1150 1200 08081-030 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 LO FREQUENCY (MHz) RF FREQUENCY (MHz) Figure 34. RF-to-IF Isolation vs. RF Frequency 0 TA = –40°C –5 Figure 37. 2LO Leakage vs. LO Frequency 0 –10 TA = +85°C LO-TO-IF LEAKAGE (dBm) 3LO LEAKAGE (dBm) TA = +25°C –10 –20 –15 –30 3LO TO RF 3LO TO IF –20 –40 –25 –50 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 LO FREQUENCY (MHz) 08081-025 –30 900 –60 900 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 LO FREQUENCY (MHz) Figure 35. LO-to-IF Leakage vs. LO Frequency Figure 38. 3LO Leakage vs. LO Frequency Rev. 0 | Page 12 of 24 ADL5357 10 9 8 CONVERSION GAIN 15 14 13 NOISE FIGURE (dB) 08081-037 30 25 SSB NOISE FIGURE (dB) CONVERSION GAIN (dB) 7 6 5 4 3 2 1 0 700 750 12 SSB NOISE FIGURE 20 11 10 9 8 VGS = 00 VGS = 01 VGS = 10 VGS = 11 15 10 7 6 5 800 850 900 950 –25 –20 –15 –10 –5 0 5 10 RF FREQUENCY (MHz) BLOCKER POWER (dBm) Figure 39. Power Conversion Gain and SSB Noise Figure vs. RF Frequency 20 18 16 30 28 26 24 22 Figure 42. SSB Noise Figure vs.10 MHz Offset Blocker Level 140 120 R9 LO SET RESISTOR SUPPLY CURRENT (mA) VGS = 00 VGS = 01 VGS = 10 VGS = 11 INPUT IP3 INPUT P1dB (dBm) 100 80 R14 IF SET RESISTOR 60 40 20 0 600 14 12 INPUT P1dB 10 8 6 700 20 18 16 1000 1050 1100 1150 1200 INPUT IP3 (dBm) 800 1000 1200 1400 1600 1800 RF FREQUENCY (MHz) BIAS RESISTOR VALUE (Ω) Figure 40. Input P1dB and Input IP3 vs. RF Frequency 12 INPUT IP3 11 25 30 Figure 43. IF or LO Supply Current vs. IF or LO Bias Resistor Value 12 INPUT IP3 11 25 30 CONVERSION GAIN AND SSB NOISE FIGURE (dB) INPUT IP3 (dBm) SSB NOISE FIGURE 9 CONVERSION GAIN 8 10 15 SSB NOISE FIGURE 9 CONVERSION GAIN 8 10 15 7 5 7 5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 LO BIAS RESISTOR VALUE (kΩ) IF BIAS RESISTOR VALUE (kΩ) Figure 41. Power Conversion Gain, SSB Noise Figure, and Input IP3 vs. LO Bias Resistor Value Figure 44. Power Conversion Gain, SSB Noise Figure, and Input IP3 vs. IF Bias Resistor Value Rev. 0 | Page 13 of 24 08081-059 0.8 1.0 1.2 1.4 1.6 1.8 08081-012 6 0.6 0 6 0 INPUT IP3 (dBm) 10 20 CONVERSION GAIN AND SSB NOISE FIGURE (dB) 10 20 08081-033 750 800 850 900 950 08081-036 08081-042 5 1000 1050 1100 1150 1200 0 –30 ADL5357 3.3 V PERFORMANCE VPOS = 3.3 V, IS = 125 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, R9 = 226 Ω, R14 = 604 Ω, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless otherwise noted. 160 150 140 SUPPLY CURRENT (mA) 80 70 TA = +85°C TA = +25°C 60 TA = +25°C TA = –40°C INPUT IP2 (dBm) 130 120 110 100 90 80 70 60 700 750 800 850 900 950 1000 1050 1100 1150 1200 TA = +85°C 50 40 30 20 10 0 700 TA = –40°C RF FREQUENCY (MHz) 08081-064 750 800 850 900 950 1000 1050 1100 1150 1200 RF FREQUENCY (MHz) Figure 45. Supply Current vs. RF Frequency at 3.3 V 12 12 Figure 48. Input IP2 vs. RF Frequency at 3.3 V 10 TA = –40°C TA = +25°C 10 TA = +25°C CONVERSION GAIN (dB) 8 TA = +85°C 6 INPUT P1dB (dBm) 8 TA = +85°C 6 TA = –40°C 4 4 2 2 08081-060 750 800 850 900 950 1000 1050 1100 1150 1200 750 800 850 900 950 1000 1050 1100 1150 1200 RF FREQUENCY (MHz) RF FREQUENCY (MHz) Figure 46. Power Conversion Gain vs. RF Frequency at 3.3 V 25 TA = –40°C 20 TA = +25°C 12 14 Figure 49. Input P1dB vs. RF Frequency at 3.3 V SSB NOISE FIGURE (dB) TA = +85°C INPUT IP3 (dBm) 10 TA = +85°C TA = +25°C 15 8 TA = –40°C 6 10 5 4 08081-062 750 800 850 900 950 1000 1050 1100 1150 1200 750 800 850 900 950 1000 1050 1100 1150 1200 RF FREQUENCY (MHz) RF FREQUENCY (MHz) Figure 47. Input IP3 vs. RF Frequency at 3.3 V Figure 50. SSB Noise Figure vs. RF Frequency at 3.3 V Rev. 0 | Page 14 of 24 08081-051 0 700 2 700 08081-063 0 700 0 700 08081-061 ADL5357 SPUR TABLES All spur tables are (N × fRF) − (M × fLO) and were measured using the standard evaluation board. Mixer spurious products are measured in dBc from the IF output power level. Data was only measured for frequencies less than 6 GHz. Typical noise floor of the measurement system = −100 dBm. 5 V Performance VPOS = 5 V, IS = 190 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless otherwise noted. Table 7. 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 −41.3 −87.1