500 MHz to 1700 MHz Balanced Mixer,
LO Buffer and RF Balun
ADL5367
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
RF frequency range of 500 MHz to 1700 MHz
IF frequency range of 30 MHz to 450 MHz
Power conversion loss: 7.7 dB
SSB noise figure of 8.3 dB
SSB noise figure with 5 dBm blocker of 21 dB
Input IP3 of 34 dBm
Typical LO drive of 0 dBm
Single-ended, 50 Ω RF and LO input ports
High isolation SPDT LO input switch
Single-supply operation: 3.3 V to 5 V
Exposed paddle 5 mm × 5 mm, 20-lead LFCSP
1500 V HBM/500 V FICDM ESD performance
VCMI
IFOP
IFON
PWDN
COMM
20
19
18
17
16
ADL5367
VPMX 1
15
LOI2
RFIN 2
14
VPSW
RFCT 3
13
VGS1
COMM 4
12
VGS0
COMM 5
11
LOI1
BIAS
GENERATOR
Cellular base station receivers
Transmit observation receivers
Radio link downconverters
GENERAL DESCRIPTION
6
7
8
9
10
VLO3
LGM3
VLO2
LOSW
NC
NC = NO CONNECT
The ADL5367 uses a highly linear, doubly balanced passive
mixer core along with integrated RF and LO balancing circuitry
to allow for single-ended operation. The ADL5367 incorporates
an RF balun, allowing optimal performance over a 500 MHz to
1700 MHz RF input frequency range. Performance is optimized for
RF frequencies from 500 MHz to 1200 MHz using a high-side LO
and for RF frequencies from 900 MHz to 1700 MHz using a
low-side LO. The balanced passive mixer arrangement provides
good LO to RF leakage, typically better than −35 dBm, and
excellent intermodulation performance. The balanced mixer
core also provides extremely high input linearity, allowing the
device to be used in demanding cellular applications where inband blocking signals may otherwise result in the degradation
of dynamic performance. A high linearity IF buffer amplifier
follows the passive mixer core to yield a typical power conversion
loss of 7.7 dB and can be used with a wide range of output
impedances.
Figure 1.
The ADL5367 provides two switched LO paths that can be
used in TDD applications where it is desirable to rapidly switch
between two local oscillators. LO current can be externally set
using a resistor to minimize dc current commensurate with the
desired level of performance. For low voltage applications, the
ADL5367 is capable of operation at voltages down to 3.3 V with
substantially reduced current. Under low voltage operation, an
additional logic pin is provided to power down (20 dB over a limited bandwidth
Typ
Unit
1700
dB
Ω
MHz
450
5.5
Ω||pF
MHz
V
14
50
500
Differential impedance, f = 200 MHz
Externally generated
Max
34||1.9
30
3.3
−6
5.0
0
12.6
50
730
+10
1670
1.0
0.4
1.4
Device enabled, IF output to 90% of the final level
Device disabled, supply current < 5 mA
Device enabled
Device disabled
Apply the supply voltage from the external circuit through the choke inductors.
PWDN function is intended for use with VS ≤ 3.6 V only.
Rev. B | Page 3 of 24
160
220
0.0
70
dBm
dB
Ω
MHz
V
V
V
ns
ns
μA
μA
ADL5367
Data Sheet
5 V PERFORMANCE
VS = 5 V, IS = 97 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless
otherwise noted.
Table 3.
Parameter
DYNAMIC PERFORMANCE
Power Conversion Loss
Voltage Conversion Loss
SSB Noise Figure
SSB Noise Figure Under Blocking
Input Third-Order Intercept (IIP3)
Input Second-Order Intercept (IIP2)
Input 1 dB Compression Point (IP1dB)1
LO to IF Leakage
LO to RF Leakage
RF to IF Isolation
IF/2 Spurious
IF/3 Spurious
POWER SUPPLY
Positive Supply Voltage
Total Quiescent Current
1
Test Conditions/Comments
Min
Typ
Max
Unit
Including 1:1 IF port transformer and printed circuit board (PCB) loss
ZSOURCE = 50 Ω, differential ZLOAD = 50 Ω differential
6.5
7.7
1.4
8.3
21
8.5
dB
dB
dB
dB
28
34
dBm
80
dBm
25
−15
−40
−47
−75
−72
dBm
dBm
dBm
dBc
dBc
dBc
5 dBm blocker present ±10 MHz from wanted RF input, LO source
filtered
fRF1 = 899.5 MHz, fRF2 = 900.5 MHz, fLO = 1103 MHz, each RF tone
at 0 dBm
fRF1 = 950 MHz, fRF2 = 900 MHz, fLO = 1103 MHz, each RF tone
at 0 dBm
Exceeding 20 dBm RF power results in damage to the device
Unfiltered IF output
0 dBm input power
0 dBm input power
4.5
5
97
VS = 5 V
5.5
V
mA
Exceeding 20 dBm RF power results in damage to the device.
3.3 V PERFORMANCE
VS = 3.3 V, IS = 56 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, R9 = 226 Ω, VGS0 = VGS1 = 0 V, and ZO = 50 Ω,
unless otherwise noted.
Table 4.
Parameter
DYNAMIC PERFORMANCE
Power Conversion Loss
Voltage Conversion Loss
SSB Noise Figure
Input Third-Order Intercept (IIP3)
Input Second-Order Intercept (IIP2)
POWER INTERFACE
Supply Voltage
Quiescent Current
Power-Down Current
Test Conditions/Comments
Min
Including 4:1 IF port transformer and PCB loss
ZSOURCE = 50 Ω, differential ZLOAD = 200 Ω differential
fRF1 = 1949.5 MHz, fRF2 = 1950.5 MHz, fLO = 1750 MHz,
each RF tone at −10 dBm
fRF1 = 1950 MHz, fRF2 = 1900 MHz, fLO = 1750 MHz,
each RF tone at −10 dBm
3.0
Resistor programmable
Device disabled
Rev. B | Page 4 of 24
Typ
Max
Unit
7.3
1
8.1
28.5
dB
dB
dB
dBm
75
dBm
3.3
56
150
3.6
V
mA
μA
Data Sheet
ADL5367
ABSOLUTE MAXIMUM RATINGS
Junction to Board Thermal Impedance
Table 5.
Parameter
Supply Voltage, VS
RF Input Level
LO Input Level
IFOP, IFON Bias Voltage
VGS0, VGS1, LOSW, PWDN
Internal Power Dissipation
Maximum Junction Temperature
Operating Temperature Range
Storage Temperature Range
Lead Temperature Range (Soldering, 60 sec)
Rating
5.5 V
20 dBm
13 dBm
6.0 V
5.5 V
1.2 W
150°C
−40°C to +85°C
−65°C to +150°C
260°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL RESISTANCE
θJA is thermal resistance, junction to ambient (°C/W), and θJB is
thermal impedance, junction to board (°C/W).
The junction to board thermal impedance (θJB) is the thermal
impedance from the die to or near the component lead of the
ADL5367. For the ADL5367, θJB is determined experimentally
to 14.74°C/W with the device mounted on a 4-layer circuit
board with two layers as ground planes in a configuration
similar to the ADL5367-EVALZ evaluation board. Board size
and complexity (number of layers) affect θJB; more layers tend to
reduce the thermal impedance slightly.
If the board temperature is known, use the junction to board
thermal impedance to calculate die temperature (also known
as junction temperature) to ensure it does not exceed the specified
limit of 150°C. For example if the board temperature is 85°C,
the die temperature is given by the equation
Tj = TB + (PDISS × θJB)
where Tj is the junction temperature.
TB is the board temperature measured at or near the
component lead.
PDISS is the power dissipated from the device.
The typical worst case power dissipation for the ADL5367 is
605 mW (5.5 V × 110 mA). Therefore Tj is
Tj = 85°C + (0.605 W × 14.74°C/W) = 93.91°C
ESD CAUTION
Table 6. Thermal Resistance
Package Type
20-Lead LFCSP
1
θJA1
25
θJB1
14.74
Unit
°C/W
See the JEDEC standard, JESD51-2, for information on optimizing thermal
impedance (PCB with 3 × 3 vias).
Rev. B | Page 5 of 24
ADL5367
Data Sheet
20
19
18
17
16
VCMI
IFOP
IFON
PWDN
COMM
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
ADL5367
TOP VIEW
(Not to Scale)
15
14
13
12
11
LOI2
VPSW
VGS1
VGS0
LOI1
NOTES
1. NC = NO CONNECT.
2. EXPOSED PAD. MUST BE SOLDERED
TO GROUND.
08083-002
VLO3 6
LGM3 7
VLO2 8
LOSW 9
NC 10
VPMX
RFIN
RFCT
COMM
COMM
Figure 2. Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
1
2
3
4, 5, 16
6, 8
7
9
10
11, 15
12, 13
14
17
18, 19
20
Mnemonic
VPMX
RFIN
RFCT
COMM
VLO3, VLO2
LGM3
LOSW
NC
LOI1, LOI2
VGS0, VGS1
VPSW
PWDN
IFON, IFOP
VCMI
EPAD (EP)
Description
Positive Supply Voltage for IF Amplifier.
RF Input. This pin must be ac-coupled.
RF Balun Center Tap (AC Ground).
Device Common (DC Ground).
Positive Supply Voltages for LO Amplifier.
LO Amplifier Bias Control.
LO Switch. LOI1 selected for 0 V, or LOI2 selected for 3 V.
No Connect.
LO Inputs. This pin must be ac-coupled.
Mixer Gate Bias Controls. 3 V logic. Ground these pins for nominal setting.
Positive Supply Voltage for LO Switch.
Power Down. Connect this pin to ground for normal operation or connect this pin to 3.0 V for disable mode.
Differential IF Outputs.
No Connect. This pin can be grounded.
Exposed pad must be soldered to ground.
Rev. B | Page 6 of 24
Data Sheet
ADL5367
TYPICAL PERFORMANCE CHARACTERISTICS
5 V PERFORMANCE
VS = 5 V, IS = 97 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless
otherwise noted.
110
100
105
90
TA = +25°C
95
TA = +85°C
90
70
TA = +85°C
60
TA = +25°C
50
85
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
40
700
08083-017
80
700
80
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
08083-023
100
INPUT IP2 (dBm)
SUPPLY CURRENT (mA)
TA = –40°C
TA = –40°C
Figure 6. Input IP2 vs. RF Frequency
Figure 3. Supply Current vs. RF Frequency
12
10.0
9.5
11
8.5
TA = +25°C
SSB NOISE FIGURE (dB)
CONVERSION LOSS (dB)
9.0
TA = +85°C
8.0
7.5
7.0
TA = –40°C
6.5
10
TA = +85ºC
9
TA = +25ºC
8
TA = –40ºC
7
6.0
6
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
Figure 4. Power Conversion Loss vs. RF Frequency
38
TA = +25°C
34
32
TA = –40°C
TA = +85°C
28
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
08083-028
INPUT IP3 (dBm)
36
26
700
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
Figure 7. SSB Noise Figure vs. RF Frequency
40
30
5
700
Figure 5. Input IP3 vs. RF Frequency
Rev. B | Page 7 of 24
08083-011
5.0
700
08083-035
5.5
ADL5367
Data Sheet
VS = 5 V, IS = 97 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless
otherwise noted.
110
86
84
VPOS = 5.25V
82
VPOS = 5.25V
100
INPUT IP2 (dBm)
SUPPLY CURRENT (mA)
105
VPOS = 5V
95
90
VPOS = 4.75V
80
78
VPOS = 5V
VPOS = 4.75V
76
74
85
–20
0
20
40
60
80
TEMPERATURE (°C)
70
–40
08083-019
80
–40
0
–20
20
80
60
40
TEMPERATURE (°C)
Figure 8. Supply Current vs. Temperature
08083-025
72
Figure 11. Input IP2 vs. Temperature
12
10.0
VPOS = 4.75V
VPOS = 5V
VPOS = 5.25V
9.5
11
SSB NOISE FIGURE (dB)
CONVERSION LOSS (dB)
9.0
8.5
8.0
7.5
7.0
6.5
10
VPOS = 5.25V
9
VPOS = 5V
8
VPOS = 4.75V
7
6.0
–20
0
20
60
40
80
TEMPERATURE (°C)
5
–40
08083-038
5.0
–40
38
VPOS = 5.25V
VPOS = 5V
VPOS = 4.75V
30
28
–20
0
20
40
TEMPERATURE (°C)
60
80
08083-030
INPUT IP3 (dBm)
34
26
–40
20
40
60
Figure 12. SSB Noise Figure vs. Temperature
40
32
0
TEMPERATURE (ºC)
Figure 9. Power Conversion Loss vs. Temperature
36
–20
Figure 10. Input IP3 vs. Temperature
Rev. B | Page 8 of 24
80
08083-012
6
5.5
Data Sheet
ADL5367
VS = 5 V, IS = 97 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless
otherwise noted.
110
85
TA = +25°C
80
TA = –40°C
75
100
INPUT IP2 (dBm)
TA = +25°C
95
TA = +85°C
90
70
65
TA = +85°C
60
85
55
80
130
180
230
280
330
380
430
IF FREQUENCY (MHz)
50
30
08083-016
80
30
TA = –40°C
80
130
180
230
280
330
380
430
380
430
IF FREQUENCY (MHz)
Figure 13. Supply Current vs. IF Frequency
08083-021
SUPPLY CURRENT (mA)
105
Figure 16. Input IP2 vs. IF Frequency
10.0
12
9.5
11
SSB NOISE FIGURE (dB)
CONVERSION LOSS (dB)
9.0
TA = +85°C
8.5
TA = +25°C
8.0
7.5
TA = –40°C
7.0
6.5
10
9
8
7
6.0
6
80
130
180
230
280
330
380
430
IF FREQUENCY (MHz)
5
30
08083-033
5.0
30
38
TA = –40°C
34
TA = +25°C
32
30
TA = +85°C
130
180
230
280
330
IF FREQUENCY (MHz)
380
430
08083-026
INPUT IP3 (dBm)
36
80
180
230
280
330
Figure 17. SSB Noise Figure vs. IF Frequency
40
26
30
130
IF FREQUENCY (MHz)
Figure 14. Power Conversion Loss vs. IF Frequency
28
80
Figure 15. Input IP3 vs. IF Frequency
Rev. B | Page 9 of 24
08083-010
5.5
ADL5367
Data Sheet
VS = 5 V, IS = 97 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless
otherwise noted.
10.0
–40
9.5
TA = +85°C
TA = +25°C
8.0
7.5
–70
TA = –40°C
–80
TA = –40°C
7.0
TA = +85°C
–2
0
2
4
6
8
10
–100
700
08083-034
–4
LO POWER (dBm)
750
850
900
950
1000 1050 1100 1150 1200
Figure 21. IF/2 Spurious vs. RF Frequency
40
–40
–45
38
TA = –40°C
–50
TA = +25°C
IF/3 SPURIOUS (dBc)
INPUT IP3 (dBm)
800
RF FREQUENCY (MHz)
Figure 18. Power Conversion Loss vs. LO Power
36
TA = +25°C
–90
6.5
6.0
–6
–60
08083-020
8.5
IF/2 SPURIOUS (dBc)
CONVERSION LOSS (dB)
–50
9.0
34
32
TA = +85°C
30
–55
–60
TA = +85°C
–65
TA = –40°C
–70
–75
TA = +25°C
28
–2
0
2
4
6
8
10
LO POWER (dBm)
Figure 19. Input IP3 vs. LO Power
TA = +25°C
TA = –40°C
75
TA = +85°C
70
65
60
55
–4
–2
0
2
4
6
LO POWER (dBm)
8
10
08083-022
INPUT IP2 (dBm)
80
50
–6
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
Figure 22. IF/3 Spurious vs. RF Frequency
90
85
–85
700
Figure 20. Input IP2 vs. LO Power
Rev. B | Page 10 of 24
08083-040
–4
08083-027
26
–6
–80
Data Sheet
ADL5367
RESISTANCE (Ω)
PERCENT (%)
80
60
40
20
MEAN: 7.7
STANDARD DEVIATION: 0.18
7.6
7.8
CONVERSION LOSS (dB)
7.4
8.0
8.2
3.6
3.4
35.5
3.2
35.0
3.0
34.5
2.8
34.0
2.6
33.5
2.4
33.0
2.2
32.5
2.0
32.0
1.8
31.5
1.6
31.0
1.4
30.5
30
08083-068
0
7.2
36.5
36.0
1.2
80
180
230
280
330
380
430
IF FREQUENCY (MHz)
Figure 26. IF Port Return Loss
Figure 23. Conversion Loss Distribution
100
0
80
5
RF RETURN LOSS (dB)
PERCENT (%)
130
08083-069
100
CAPACITANCE (pF)
VS = 5 V, IS = 97 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless
otherwise noted.
60
40
20
10
15
20
33
35
INPUT IP3 (dBm)
37
39
25
700
750
2
80
4
LO RETURN LOSS (dB)
90
70
60
50
40
30
8.4
8.6
1000 1050 1100 1150 1200
8
10
12
SELECTED
14
UNSELECTED
18
MEAN: 8.3
STANDARD DEVIATION: 0.05
8.2
950
6
16
20
8.8
NOISE FIGURE (dB)
9.0
08083-063
PERCENTAGE (%)
0
8.0
900
Figure 27. RF Port Return Loss, Fixed IF
100
0
7.8
850
RF FREQUENCY (MHz)
Figure 24. Input IP3 Distribution
10
800
Figure 25. SSB Noise Figure Distribution
20
900
950
1000 1050 1100 1150 1200 1250 1300 1350 1400
LO FREQUENCY (MHz)
Figure 28. LO Return Loss, Selected and Unselected
Rev. B | Page 11 of 24
08083-007
31
08083-067
0
08083-013
MEAN: 34.67
STANDARD DEVIATION: 0.19
ADL5367
Data Sheet
70
–20
65
–25
LO-TO-RF LEAKAGE (dBm)
LO SWITCH ISOLATION (dB)
VS = 5 V, IS = 97 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless
otherwise noted.
TA = +25°C
60
TA = –40°C
55
TA = +85°C
50
–30
–35
TA = +85°C
TA = –40°C
–40
–45
45
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
–50
900
08083-059
750
Figure 32. LO to RF Leakage vs. LO Frequency
–40
0
TA = +85°C
–5
–10
TA = +25°C
2LO LEAKAGE (dBm)
–46
–48
–50
–52
TA = –40°C
–54
–15
–25
–30
–35
–40
–58
–45
950
1000 1050 1100 1150 1200 1250 1300 1350 1400
RF FREQUENCY (MHz)
–50
900
950
1000 1050 1100 1150 1200 1250 1300 1350 1400
LO FREQUENCY (MHz)
0
0
–10
3LO LEAKAGE (dBm)
–5
TA = –40°C
TA = +25°C
–15
TA = +85°C
–20
–25
–20
3LO TO IF
–30
–40
–50
3LO TO RF
950
1000 1050 1100 1150 1200 1250 1300 1350 1400
LO FREQUENCY (MHz)
–70
900
950
1000 1050 1100 1150 1200 1250 1300 1350 1400
LO FREUQENCY (MHz)
Figure 34. 3LO Leakage vs. LO Frequency
Figure 31. LO to IF Leakage vs. LO Frequency
Rev. B | Page 12 of 24
08083-015
–60
08083-031
LO-TO-IF LEAKAGE (dBm)
2LO TO IF
Figure 33. 2LO Leakage vs. LO Frequency
Figure 30. RF to IF Isolation vs. RF Frequency
–30
900
2LO TO RF
–20
–56
08083-039
RF-TO-IF ISOLATION (dBc)
–44
08083-014
–42
–10
1000 1050 1100 1150 1200 1250 1300 1350 1400
LO FREQUENCY (MHz)
Figure 29. LO Switch Isolation vs. RF Frequency
–60
900
950
08083-032
TA = +25°C
40
700
Data Sheet
ADL5367
VS = 5 V, IS = 97 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless
otherwise noted.
15
10
30
14
9
12
6
11
10
5
NOISE FIGURE
4
9
8
3
VGS = 0,
VGS = 0,
VGS = 1,
VGS = 1,
1
0
700
750
5
850
900
950
5
1000 1050 1100 1150 1200
Figure 35. Power Conversion Loss and SSB Noise Figure vs. RF Frequency
40
VGS = 0,
VGS = 0,
VGS = 1,
VGS = 1,
38
36
0
1
0
1
32
30
28
26
24
22
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
08083-062
INPUT IP3 (dBm)
34
750
10
6
RF FREQUENCY (MHz)
20
700
15
7
0
1
0
1
800
20
Figure 36. Input IP3 vs. RF Frequency
Rev. B | Page 13 of 24
0
–30
–25
–20
–15
–10
–5
0
5
BLOCKER POWER (dBm)
Figure 37. SSB Noise Figure vs.10 MHz Offset Blocker Level
10
08083-003
2
NOISE FIGURE (dB)
7
25
SSB NOISE FIGURE (dB)
13
08083-058
CONVERSION LOSS (dB)
CONVERSION LOSS
8
ADL5367
Data Sheet
3.3 V PERFORMANCE
VS = 3.3 V, IS = 56 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, R9 = 226 Ω, VGS0 = VGS1 = 0 V, and ZO = 50 Ω,
unless otherwise noted.
85
64
80
TA = –40°C
75
60
TA = –40°C
TA = +25°C
58
INPUT IP2 (dBm)
56
TA = +85°C
54
TA = +25°C
65
TA = +85°C
60
55
50
52
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
40
700
9.5
9.5
9.0
9.0
NOISE FIGURE (dB)
8.5
TA = +85°C
TA = +25°C
7.5
7.0
6.5
TA = –40°C
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
34
32
TA = –40°C
28
TA = +85°C
26
TA = +25°C
24
22
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
08083-029
INPUT IP3 (dBm)
30
750
TA = –40°C
7.0
6.5
5.0
700
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
Figure 42. SSB Noise Figure vs. RF Frequency at 3.3 V
Figure 39. Power Conversion Loss vs. RF Frequency at 3.3 V
20
700
TA = +85°C
7.5
5.5
900
1000 1050 1100 1150 1200
TA = +25°C
5.5
850
950
8.0
6.0
800
900
8.5
6.0
08083-036
CONVERSION LOSS (dB)
10.0
750
850
Figure 41. Input IP2 vs. RF Frequency at 3.3 V
10.0
5.0
700
800
RF FREQUENCY (MHz)
Figure 38. Supply Current vs. RF Frequency at 3.3 V
8.0
750
08083-024
45
08083-018
50
700
70
Figure 40. Input IP3 vs. RF Frequency at 3.3 V
Rev. B | Page 14 of 24
08083-064
SUPPLY CURRENT (mA)
62
Data Sheet
ADL5367
UPCONVERSION
10.0
9.5
9.5
9.0
9.0
8.5
8.0
TA = +85°C
7.5
7.0
TA = –40°C
TA = +25°C
6.5
8.5
8.0
6.5
6.0
5.5
5.5
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
Figure 43. Power Conversion Loss vs. RF Frequency, VS = 5 V, Upconversion
TA = +25°C
7.0
6.0
5.0
700
TA = +85°C
7.5
5.0
700
TA = –40°C
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
08083-066
CONVERSION LOSS (dB)
10.0
08083-065
CONVERSION LOSS (dB)
TA = 25°C, fIF = 153 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless otherwise noted.
Figure 45. Power Conversion Loss vs. RF Frequency at 3.3 V, Upconversion
34
34
TA = –40°C
TA = +25°C
32
32
30
26
28
TA = +25°C
24
22
22
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
Figure 44. Input IP3 vs. RF Frequency, VS = 5 V, Upconversion
TA = +85°C
26
24
20
700
TA = –40°C
20
700
750
800
850
900
950
1000 1050 1100 1150 1200
RF FREQUENCY (MHz)
Figure 46. Input IP3 vs. RF Frequency at 3.3 V, Upconversion
Rev. B | Page 15 of 24
08083-061
INPUT IP3 (dBm)
28
08083-060
INPUT IP3 (dBm)
TA = +85°C
30
ADL5367
Data Sheet
SPUR TABLES
All spur tables are (N × fRF) − (M × fLO) and were measured using the standard evaluation board. Mixer spurious products are measured
in dBc from the IF output power level. Data was measured only for frequencies less than 6 GHz. Typical noise floor of the measurement
system = −100 dBm.
5 V Performance
VS = 5 V, IS = 97 mA, TA = 25°C, fRF = 900 MHz, fLO = 1103 MHz, LO power = 0 dBm, RF power = 0 dBm, VGS0 = VGS1 = 0 V, and
ZO = 50 Ω, unless otherwise noted.
M
0
N
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
−39.7
−84.6
工商网监
湘ICP备2023018690号
