Half-Duplex, iCoupler
Isolated RS-485 Transceiver
ADM2481
Data Sheet
FUNCTIONAL BLOCK DIAGRAM
VDD1
VDD2
ADM2481
DE
TxD
RxD
A
B
RE
GND2
GND1
08920-001
RS-485 transceiver with electrical data isolation
Complies with ANSI TIA/EIA-485-A and ISO 8482: 1987(E)
500 kbps data rate
Slew rate-limited driver outputs
Low power operation: 2.5 mA maximum
Suitable for 5 V or 3.3 V operations (VDD1)
High common-mode transient immunity: >25 kV/μs
True fail-safe receiver inputs
Chatter-free power-up/power-down protection
256 nodes on bus
Thermal shutdown protection
Safety and regulatory approvals
UL recognition: 2500 V rms for 1 minute per
UL 1577
VDE certificates of conformity
DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12
VIORM = 560 V peak
Operating temperature range: −40°C to +85°C
GALVANIC ISOLATION
FEATURES
Figure 1.
APPLICATIONS
Low power RS-485/RS-422 networks
Isolated interfaces
Building control networks
Multipoint data transmission systems
GENERAL DESCRIPTION
The ADM2481 differential bus transceiver is an integrated,
galvanically isolated component designed for bidirectional data
communication on balanced, multipoint bus transmission lines.
It complies with ANSI EIA/TIA-485-A and ISO 8482: 1987(E).
Using iCoupler® technology from Analog Devices, Inc., the
ADM2481 combines a 3-channel isolator, a three-state differential line driver, and a differential input receiver into a single
package. The logic side of the device is powered with either a
5 V or 3 V supply, and the bus side uses a 5 V supply only.
The ADM2481 is slew-limited to reduce reflections with improperly terminated transmission lines. The controlled slew rate
limits the data rate to 500 kbps. The input impedance of the
device is 96 kΩ, allowing up to 256 transceivers on the bus. Its
driver has an active-high enable feature. The driver differential
outputs and receiver differential inputs are connected internally
Rev. B
to form a differential input/output (I/O) port. When the driver
is disabled or when VDD1 or VDD2 = 0 V, this imposes minimal
loading on the bus. An active-high receiver disable feature,
which causes the receiver output to enter a high impedance
state, is provided as well.
The receiver inputs have a true fail-safe feature that ensures a
logic-high receiver output level when the inputs are open or
shorted. This guarantees that the receiver outputs are in a
known state before communication begins and at the point
when communication ends.
Current limiting and thermal shutdown features protect against
output short circuits and bus contention situations that might
cause excessive power dissipation. The part is fully specified
over the industrial temperature range of −40°C to +85°C and is
available in a 16-lead, wide body SOIC package.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2010–2018 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADM2481
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................8
Applications ....................................................................................... 1
Test Circuits ..................................................................................... 11
Functional Block Diagram .............................................................. 1
Switching Characteristics .............................................................. 12
General Description ......................................................................... 1
Circuit Description......................................................................... 13
Revision History ............................................................................... 2
Electrical Isolation...................................................................... 13
Specifications..................................................................................... 3
Truth Tables................................................................................. 14
Timing Specifications .................................................................. 4
Thermal Shutdown .................................................................... 14
Package Characteristics ............................................................... 4
True Fail-Safe Receiver Inputs .................................................. 14
Regulatory Information ............................................................... 4
Magnetic Field Immunity.......................................................... 14
Insulation and Safety-Related Specifications ............................ 4
Applications Information .............................................................. 16
VDE 0884 Insulation Characteristics ........................................ 5
Printed Circuit Board (PCB) Layout ....................................... 16
Absolute Maximum Ratings............................................................ 6
Isolated Power Supply Circuit .................................................. 16
ESD Caution .................................................................................. 6
Outline Dimensions ....................................................................... 17
Pin Configuration and Function Descriptions ............................. 7
Ordering Guide .......................................................................... 17
REVISION HISTORY
4/2018—Rev. A to Rev. B
Change to Minimum External Air Gap (Clearance)
Parameter, Value Column, Table 5 ................................................. 4
6/2012—Rev. 0 to Rev. A
Updated Safety and Regulatory Approvals (Throughout) .......... 1
Updated Outline Dimensions ....................................................... 17
Changes to Ordering Guide .......................................................... 17
7/2010—Revision 0: Initial Version
Rev. B | Page 2 of 17
Data Sheet
ADM2481
SPECIFICATIONS
3.0 V ≤ VDD1 ≤ 5.5 V, 4.75 V ≤ VDD2 ≤ 5.25 V, TA = TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter
DRIVER
Differential Outputs
Differential Output Voltage
Δ |VOD| for Complementary Output States
Common-Mode Output Voltage
Δ |VOC| for Complementary Output States
Output Short-Circuit Current,
VOUT = High
VOUT = Low
Logic Inputs
Input High Voltage
Input Low Voltage
CMOS Logic Input Current (TxD, DE, RE)
RECEIVER
Differential Inputs
Differential Input Threshold Voltage
Input Hysteresis
Input Resistance (A, B)
Input Current (A, B)
RxD Logic Output
Output High Voltage
Output Low Voltage
Output Short-Circuit Current
Three-State Output Leakage Current
POWER SUPPLY CURRENT
Logic Side
Bus Side
COMMON-MODE TRANSIENT IMMUNITY 1
1
Symbol
Min
VOD
VOD
VOD3
2.0
1.5
1.5
Typ
VOC
Max
Unit
Test Conditions/Comments
5
5
5
5
V
V
V
V
0.2
3
0.2
V
V
V
RL = ∞, see Figure 16
RL = 50 Ω (RS-422), see Figure 16
RL = 27 Ω (RS-485), see Figure 16
VTEST = −7 V to +12 V, VDD1 ≥ 4.75,
see Figure 17
RL = 27 Ω or 50 Ω, see Figure 16
RL = 27 Ω or 50 Ω, see Figure 16
RL = 27 Ω or 50 Ω, see Figure 16
+250
+250
mA
mA
−7 V ≤ VOUT ≤ +12 V
−7 V ≤ VOUT ≤ +12 V
0.25 VDD1
+10
V
V
µA
TxD, DE, RE
TxD, DE, RE
TxD, DE, RE = VDD1 or 0 V
0.125
−0.1
mV
mV
kΩ
mA
mA
−7 V ≤ VCM ≤ +12 V
−7 V ≤ VCM ≤ +12 V
−7 V ≤ VCM ≤ +12 V
VIN = 12 V
VIN = −7 V
0.1
0.4
85
±1
V
V
V
V
mA
µA
IOUT = 20 µA, VA − VB = 0.2 V
IOUT = 4 mA, VA − VB = 0.2 V
IOUT = −20 µA, VA − VB = −0.2 V
IOUT = −4 mA, VA − VB = −0.2 V
VOUT = GND or VCC
0.4 V ≤ VOUT ≤ 2.4 V
2.5
mA
1.3
mA
2.0
1.7
mA
mA
kV/µs
4.5 V ≤ VDD1 ≤ 5.5 V, outputs
unloaded, RE = 0 V
3.0 V ≤ VDD1 ≤ 3.6 V, outputs
unloaded, RE = 0 V
Outputs unloaded, DE = 5 V
Outputs unloaded, DE = 0 V
TxD = VDD1 or 0 V, VCM = 1 kV,
transient magnitude = 800 V
ISC
−250
−250
VIH
VIL
II
VTH
VHYS
0.7 VDD1
−10
+0.01
−200
−125
20
150
96
VOH
VDD1 − 0.1
VDD1 − 0.4
VDD1 − 0.2
VOL
ISC
7
IDD1
IDD2
VCM
−30
25
Common-mode transient immunity is the maximum common-mode voltage slew rate that can be sustained while maintaining specification-compliant operation.
VCM is the common-mode potential difference between the logic and bus sides. The transient magnitude is the range over which the common mode is slewed. The
common-mode voltage slew rates apply to both rising and falling common-mode voltage edges.
Rev. B | Page 3 of 17
ADM2481
Data Sheet
TIMING SPECIFICATIONS
3.0 V ≤ VDD1 ≤ 5.5 V, 4.75 V ≤ VDD2 ≤ 5.25 V, TA = TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter
DRIVER
Maximum Data Rate
Propagation Delay
Skew
Rise/Fall Time
Enable Time
Disable Time
RECEIVER
Propagation Delay
Differential Skew
Enable Time
Disable Time
Symbol
tPLH, tPHL
tSKEW
tR, tF
tPLH, tPHL
tSKEW
Min
Typ
500
250
200
400
25
40
Max
Unit
Test Conditions/Comments
620
40
600
1050
1050
kbps
ns
ns
ns
ns
ns
RL = 54 Ω, CL1 = CL2 = 100 pF, see Figure 18 and Figure 22
RL = 54 Ω, CL1 = CL2 = 100 pF, see Figure 18 and Figure 22
RL = 54 Ω, CL1 = CL2 = 100 pF, see Figure 18 and Figure 22
RL = 500 Ω, CL = 100 pF, see Figure 19 and Figure 24
RL = 500 Ω, CL = 15 pF, see Figure 19 and Figure 24
1050
250
70
70
ns
ns
ns
ns
CL = 15 pF, see Figure 20 and Figure 23
CL = 15 pF, see Figure 20 and Figure 23
RL = 1 kΩ, CL = 15 pF, see Figure 21 and Figure 25
RL = 1 kΩ, CL = 15 pF, see Figure 21 and Figure 25
PACKAGE CHARACTERISTICS
Table 3.
Parameter
Resistance (Input-Output) 1
Capacitance (Input-Output)1
Input Capacitance 2
1
2
Symbol
RI-O
CI-O
CI
Min
Typ
1012
3
4
Max
Unit
Ω
pF
pF
Test Conditions
f = 1 MHz
Device is considered a 2-terminal device: Pin 1 to Pin 8 are shorted together, and Pin 9 to Pin16 are shorted together.
Input capacitance is from any input data pin to ground.
REGULATORY INFORMATION
Table 4. ADM2481 Approvals
Organization
UL
Approval Type
Recognized under the Component Recognition
Program of Underwriters Laboratories, Inc.
VDE
Certified according to DIN V VDE V 0884-10
(VDE V 0884-10): 2006-12
Notes
In accordance with UL 1577, each ADM2481 is proof tested by
applying an insulation test voltage of ≥ 3000 V rms for 1 second
(current leakage detection limit = 5 µA).
In accordance with DIN V VDE V 0884-10, each ADM2481 is proof
tested by applying an insulation test voltage of ≥ 1050 V peak for
1 second (partial discharge detection limit = 5 pC).
INSULATION AND SAFETY-RELATED SPECIFICATIONS
Table 5.
Parameter
Rated Dielectric Insulation Voltage
Minimum External Air Gap (Clearance)
Symbol
L(I01)
Value
2500
7.6
Unit
V rms
mm
Minimum External Tracking (Creepage)
L(I02)
7.6
mm
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Isolation Group
CTI
0.017 min
>175
IIIa
mm
V
Rev. B | Page 4 of 17
Conditions
1-minute duration
Measured from input terminals to output
terminals, shortest distance through air
Measured from input terminals to output
terminals, shortest distance along body
Insulation distance through insulation
DIN IEC 112/VDE 0303 Part 1
Material Group (Table 1 in DIN VDE 0110,1/89)
Data Sheet
ADM2481
VDE 0884 INSULATION CHARACTERISTICS
This isolator is suitable for basic electrical isolation only within this safety limit data. Maintenance of this safety data shall be ensured by
means of protective circuits.
Table 6.
Description
Installation Classification per DIN VDE 0110 for Rated Mains Voltage
≤150 V rms
≤300 V rms
≤400 V rms
Climatic Classification
Pollution Degree (Table 1 in DIN VDE 0110)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b1
VIORM × 1.875 = VPR, 100% Production Tested
tm = 1 sec, Partial Discharge of < 5 pC
Input-to-Output Test Voltage, Method a
(After Environmental Tests, Subgroup 1)
VIORM × 1.6 = VPR, tm = 60 sec, Partial Discharge of < 5 pC
(After Input and/or Safety Test, Subgroup 2/3)
VIORM × 1.2 = VPR, tm = 60 sec, Partial Discharge of < 5 pC
Highest Allowable Overvoltage
(Transient Overvoltage, tTR = 10 sec)
Safety-Limiting Values (Maximum Value Allowed in the Event of a Failure; see Figure 13)
Case Temperature
Input Current
Output Current
Insulation Resistance at TS, VIO = 500 V
Rev. B | Page 5 of 17
Symbol
Characteristic
Unit
VIORM
VPR
I to IV
I to III
I to II
40/85/21
2
560
1050
VPEAK
VPEAK
896
VPEAK
VPR
672
VPEAK
VTR
4000
VPEAK
TS
IS, INPUT
IS, OUTPUT
RS
150
265
335
>109
°C
mA
mA
Ω
ADM2481
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted. All voltages are relative to
their respective ground.
Table 7.
Parameter
VDD1
VDD2
Digital Input Voltage (DE, RE, TxD)
Digital Output Voltage (RxD)
Driver Output/Receiver Input Voltage
ESD Rating: Contact
Human Body Model (A, B Pins
Operating Temperature Range
Storage Temperature Range
Average Output Current per Pin
θJA Thermal Impedance
Lead Temperature
Soldering (10 sec)
Vapor Phase (60 sec)
Infrared (15 sec)
Rating
−0.5 V to +7 V
−0.5 V to +6 V
−0.5 V to VDD1 + 0.5 V
−0.5 V to VDD1 + 0.5 V
−9 V to +14 V
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
±2 kV
−40°C to +85°C
−55°C to +150°C
−35 mA to +35 mA
65°C/W
260°C
215°C
220°C
Rev. B | Page 6 of 17
Data Sheet
ADM2481
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
16 VDD2
VDD1 1
15 GND21
GND11 2
RxD 3
RE 4
ADM2481
14 NC
13 B
TOP VIEW
DE 5 (Not to Scale) 12 A
TxD 6
11 NC
GND11 7
10 GND21
GND11 8
9
GND21
PIN 9, PIN 10, AND PIN 15 MUST BE CONNECTED TO GND2.
08920-002
NC = NO CONNECT
1 PIN 2, PIN 7, AND PIN 8 MUST BE CONNECTED TO GND .
1
Figure 2. Pin Configuration
Table 8. Pin Function Descriptions
Pin No.
1
2, 7, 8
3
Mnemonic
VDD1
GND1
RxD
4
RE
5
6
9, 10, 15
11, 14
12
DE
TxD
GND2
NC
A
13
B
16
VDD2
Description
Power Supply (Logic Side).
Ground (Logic Side).
Receiver Output Data. When enabled, if (A − B) ≥ −30 mV, then RxD = high; if (A − B) ≤ −200 mV, then
RxD = low. This is a tristate output when the receiver is disabled, that is, when RE is driven high.
Receiver Enable Input. This is an active-low input. Driving this input low enables the receiver, and
driving it high disables the receiver.
Driver Enable Input. Driving the input high enables the driver, and driving it low disables the driver.
Transmit Data Input. Data to be transmitted by the driver is applied to this input.
Ground (Bus Side).
No Connect.
Noninverting Driver Output/Receiver Input. When the driver is disabled, or when VDD1 or VDD2 is
powered down, Pin A is put into a high impedance state to avoid overloading the bus.
Inverting Driver Output/Receiver Input. When the driver is disabled, or when VDD1 or VDD2 is powered
down, Pin B is put into a high impedance state to avoid overloading the bus.
Power Supply (Bus Side).
Rev. B | Page 7 of 17
ADM2481
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
0.32
1.6
IDD1 _RCVR_ENABLE @ 5.5V
1.4
OUTPUT VOLTAGE (V)
SUPPLY CURRENT (mA)
0.30
1.2
1.0
0.8
IDD2 _DE_ENABLE @ 5.5V
0.6
0.28
0.26
0.24
0.4
08920-038
0
0.20
–40
85
25
–40
08920-031
0.22
0.2
–25
35
80
65
50
TEMPERATURE (°C)
Figure 6. Receiver Output Low Voltage vs. Temperature, IOUT = –4 mA
Figure 3. Unloaded Supply Current vs. Temperature
120
4.78
100
4.76
OUTPUT VOLTAGE (V)
80
60
40
4.74
4.72
4.70
4.68
20
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
OUTPUT VOLTAGE (V)
4.66
–40
08920-014
0
08920-032
OUTPUT CURRENT (mA)
20
5
–10
TEMPERATURE (°C)
–25
–10
5
20
35
50
80
65
TEMPERATURE (°C)
Figure 4. Output Current vs. Driver Output Low Voltage
Figure 7. Receiver Output High Voltage vs. Temperature, IOUT = 4 mA
90
DRIVER OUTPUT CURRENT (mA)
80
–30
–50
–70
–90
70
60
50
40
30
20
–110
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
OUTPUT VOLTAGE (V)
5.0
Figure 5. Output Current vs. Driver Output High Voltage
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
DIFFERENTIAL OUTPUT VOLTAGE (V)
Figure 8. Driver Output Current vs. Differential Output Voltage
Rev. B | Page 8 of 17
08920-013
10
08920-015
OUTPUT CURRENT (mA)
–10
Data Sheet
ADM2481
600
500
1
tPLHA
tPHLA
tPLHB
tPHLB
300
200
2
0
–40
08920-034
100
–15
10
35
60
4
85
CH1 5.00V
CH3 1.00V
TEMPERATURE (°C)
Figure 9. Driver Propagation Delay vs. Temperature
CH2 1.00V
CH4 5.00V
M200ns
A CH1
T
1.33600µs
3.10V
08920-022
TIME (ns)
400
Figure 11. Driver/Receiver Propagation Delay, High to Low
800
700
tPHL
1
600
tPLH
400
300
200
2
0
–40
–15
10
35
60
4
85
CH1 5.00V
CH3 1.00V
TEMPERATURE (°C)
Figure 10. Receiver Propagation Delay vs. Temperature
CH2 1.00V
CH4 5.00V
M200ns
A CH1
T
360.000ns
3.10V
Figure 12. Driver/Receiver Propagation Delay, Low to High
Rev. B | Page 9 of 17
08920-023
100
08920-035
TIME (ns)
500
Data Sheet
0
300
–5
OUTPUT CURRENT (mA)
350
250
BUS SIDE
200
150
LOGIC SIDE
100
50
0
200
150
100
CASE TEMPERATURE (°C)
Figure 13. Thermal Derating Curve, Dependence of Safety-Limiting Values
with Case Temperature per VDE 0884
35
30
25
20
15
10
5
0
0
0.25
0.50
0.75
1.00
1.25
1.50
1.75
2.00
2.25
OUTPUT VOLTAGE (V)
08920-037
OUTPUT CURRENT (mA)
–15
–20
Figure 14. Output Current vs. Receiver Output Low Voltage
Rev. B | Page 10 of 17
–30
3.0
3.2
3.4
3.6
3.8
4.0
4.2
4.4
4.6
4.8
5.0
OUTPUT VOLTAGE (V)
Figure 15. Output Current vs. Receiver Output High Voltage
08920-036
0
–10
–25
50
08920-024
SAFETY-LIMITING CURRENT (mA)
ADM2481
Data Sheet
ADM2481
TEST CIRCUITS
VCC
A
0V OR 3V
VOC
08920-003
RL
RL
S1
DE
S2
CL
VOUT
B
DE IN
Figure 16. Driver Voltage Measurement
08920-006
RL
VOD
Figure 19. Driver Enable/Disable
375Ω
A
VOUT
RE
CL
Figure 17. Driver Voltage Measurement over Common-Mode Range
Figure 20. Receiver Propagation Delay
VCC
+1.5V
S1
A
CL2
08920-005
RL
B
–1.5V
CL1
RL
RE
S2
CL
VOUT
RE IN
Figure 18. Driver Propagation Delay
Figure 21. Receiver Enable/Disable
Rev. B | Page 11 of 17
08920-008
375Ω
B
08920-007
VTEST
60Ω
08920-004
VOD3
ADM2481
Data Sheet
SWITCHING CHARACTERISTICS
VDD1
0.7VDD1
0.5VDD1
0.5VDD1
DE
0V
tPLH
B
0.5VDD1
0.5VDD1
tPHL
0.3VDD1
tLZ
tZL
1/2VOD
VOD
A
VOL + 0.5V
VOL
90% POINT
90% POINT
tHZ
tZH
VOH
A, B
10% POINT
10% POINT
tR
VOH – 0.5V
A, B
2.3V
04736-009
VOL
tF
0V
Figure 22. Driver Propagation Delay, Rise/Fall Timing
08920-011
VOH
2.3V
A, B
tSKEW = |tPLH – tPHL|
Figure 24. Driver Enable/Disable Timing
0.7VDD1
RE
0.5VDD1
0.5VDD1
0.3VDD1
tZL
0V
tLZ
0V
1.5V
RxD
VOL + 0.5V
OUTPUT LOW
tPHL
tPLH
tZH
VOH
VOL
tHZ
OUTPUT HIGH
1.5V
tSKEW = |tPLH – tPHL|
1.5V
VOL
VOH
VOH – 0.5V
RxD
08920-010
RxD
1.5V
0V
Figure 23. Receiver Propagation Delay
Figure 25. Receiver Enable/Disable Timing
Rev. B | Page 12 of 17
08920-012
A–B
Data Sheet
ADM2481
CIRCUIT DESCRIPTION
ELECTRICAL ISOLATION
iCoupler Technology
In the ADM2481, electrical isolation is implemented on the
logic side of the interface. Therefore, the part has two main
sections: a digital isolation section and a transceiver section (see
Figure 26). Driver input and data enable signals, applied to the
TxD and DE pins, respectively, and referenced to logic ground
(GND1), are coupled across an isolation barrier to appear at the
transceiver section referenced to isolated ground (GND2).
Similarly, the receiver output, referenced to isolated ground in
the transceiver section, is coupled across the isolation barrier
to appear at the RxD pin referenced to logic ground (GND1).
The digital signals are transmitted across the isolation barrier
using iCoupler technology. This technique uses chip scale transformer windings to couple the digital signals magnetically from
one side of the barrier to the other. Digital inputs are encoded
into waveforms that are capable of exciting the primary transformer winding. At the secondary winding, the induced waveforms
are then decoded into the binary value that was originally
transmitted.
VDD1
VDD2
ISOLATION
BARRIER
ENCODE
TxD
DECODE
D
A
B
DE
ENCODE
DECODE
RxD
DECODE
ENCODE
R
DIGITAL ISOLATION
GND1
TRANSCEIVER
GND2
Figure 26. Digital Isolation and Transceiver Sections
Rev. B | Page 13 of 17
04736-025
RE
ADM2481
Data Sheet
TRUTH TABLES
TRUE FAIL-SAFE RECEIVER INPUTS
The following truth tables use the abbreviations shown in Table 9.
The receiver inputs have a true fail-safe feature that ensures that
the receiver output is high when the inputs are open or shorted.
During line-idle conditions, when no driver on the bus is
enabled, the voltage across a terminating resistance at the
receiver input decays to 0 V. With traditional transceivers,
receiver input thresholds specified between −200 mV and
+200 mV mean that external bias resistors are required on the
A and B pins to ensure that the receiver outputs are in a known
state. The true fail-safe receiver input feature eliminates the
need for bias resistors by specifying the receiver input threshold between −30 mV and −200 mV. The guaranteed negative
threshold means that when the voltage between A and B decays
to 0 V, the receiver output is guaranteed to be high.
Table 9.
Letter
H
L
X
Z
NC
Description
High level
Low level
Don’t care
High impedance (off )
Disconnected
Table 10. Transmitting
Supply Status
VDD1
VDD2
On
On
On
On
On
On
On
Off
Off
On
Off
Off
DE
H
H
L
X
L
X
Inputs
TxD
H
L
X
X
L
X
A
H
L
Z
Z
Z
Z
Outputs
B
L
H
Z
Z
Z
Z
MAGNETIC FIELD IMMUNITY
Because iCouplers use a coreless technology, no magnetic
components are present, and the problem of magnetic saturation of the core material does not exist. Therefore, iCouplers
have essentially infinite dc field immunity. The analysis that
follows defines the conditions under which this might occur.
The 3 V operating condition of the ADM2481 is examined
because it represents the most susceptible mode of operation.
Table 11. Receiving
Supply Status
VDD1
On
On
On
On
On
On
Off
VDD2
On
On
On
On
On
Off
Off
Inputs
A − B (V)
>−0.03
1.0 V to 0.75 V. This is well above the 0.5 V sensing threshold
of the decoder.
DISTANCE = 1m
100.00
100M
08920-028
MAXIMUM ALLOWABLE CURRENT (kA)
10.000
08920-027
MAXIMUM ALLOWABLE MAGNETIC
FLUX DENSITY (kGAUSS)
100.000
Figure 28. Maximum Allowable Current for Various
Current-to-ADM2481 Spacings
At combinations of strong magnetic field and high frequency,
any loops formed by printed circuit board traces could induce
large enough error voltages to trigger the thresholds of succeeding circuitry. To avoid this possibility, take care in the layout of
such traces.
Rev. B | Page 15 of 17
ADM2481
Data Sheet
APPLICATIONS INFORMATION
In applications involving high common-mode transients, take
care to ensure that board coupling across the isolation barrier
is minimized. Furthermore, the board layout must be designed
such that any coupling that does occur equally affects all pins
on a given component side.
PRINTED CIRCUIT BOARD (PCB) LAYOUT
The ADM2481 signal isolated RS-485 transceiver requires no
external interface circuitry for the logic interfaces. Power supply
bypassing is required at the input and output supply pins (see
Figure 29).
Failure to ensure this can cause voltage differentials between
pins that exceed the absolute maximum ratings of the device,
thereby leading to latch-up or permanent damage.
Bypass capacitors are most conveniently connected between
Pin 1 and Pin 2 for VDD1 and between Pin 15 and Pin 16 for
VDD2. The capacitor value must be between 0.01 μF and 0.1 μF.
The total lead length between both ends of the capacitor and
the input power supply pin must not exceed 20 mm.
VDD2
GND2
NC
B
A
NC
GND2
GND2
NC = NO CONNECT
Figure 29. Recommended Printed Circuit Board Layout
ISOLATION
BARRIER
VCC
SD103C
TRANSFORMER
DRIVER
22µF
VCC
OUT
IN
+
SD ADP3330
ERR
NR
5V
+
10µF
GND
78253
SD103C
VCC
VDD1
VDD2
ADM2481
GND1
GND2
Figure 30. Isolated Power Supply Circuit
Rev. B | Page 16 of 17
08920-029
ADM2481
The ADM2481 requires isolated power capable of 5 V at
100 mA to be supplied between the VDD2 and GND2 pins. If
no suitable integrated power supply is available, a discrete
circuit, such as the one in Figure 30, can be used. A centertapped transformer provides electrical isolation. The primary
winding is excited with a pair of square waveforms that are 180°
out of phase with each other. A pair of Schottky diodes and a
smoothing capacitor are used to create a rectified signal from
the secondary winding. The ADP3330 linear voltage regulator
provides a regulated power supply to the bus-side circuitry of
the ADM2481.
08920-127
VDD1
GND1
RxD
RE
DE
TxD
GND1
GND1
ISOLATED POWER SUPPLY CIRCUIT
Data Sheet
ADM2481
OUTLINE DIMENSIONS
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
8
1.27 (0.0500)
BSC
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
10.65 (0.4193)
10.00 (0.3937)
0.75 (0.0295)
45°
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
SEATING
PLANE
8°
0°
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
1.27 (0.0500)
0.40 (0.0157)
03-27-2007-B
1
Figure 31. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model 1
ADM2481BRWZ
ADM2481BRWZ-RL7
EVAL-ADM2481EBZ
1
Data Rate (kbps)
500
500
Temperature Range
−40°C to +85°C
−40°C to +85°C
Z = RoHS Compliant Part.
©2010–2018 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08920-0-4/18(B)
Rev. B | Page 17 of 17
Package Description
16-Lead, Wide Body SOIC_W
16-Lead, Wide Body SOIC_W
ADM2481 Evaluation Board
Package Option
RW-16
RW-16
工商网监
湘ICP备2023018690号
