FEATURES
FUNCTIONAL BLOCK DIAGRAMS
APPLICATIONS
VCC
ADM8612
RESET
VIN
RESET
GENERATOR
VTH
MR
DEBOUNCE
12782-001
Ultralow power consumption with ICC = 92 nA (typical)
Continuous monitoring with no blank time
Pretrimmed voltage monitoring threshold options
10 options from 2 V to 4.63 V for the ADM8611
20 options from 0.5 V to 1.9 V for the ADM8612/ADM8615
5 options from 2.32 V to 4.63 V for the ADM8613/ADM8614
±1.3% threshold accuracy over full temperature range
Manual reset input (ADM8611/ADM8612/ADM8613/ADM8615)
200 ms (typical) reset timeout
Low voltage input monitoring down to 0.5 V (ADM8612/
ADM8615)
Watchdog timer (ADM8613/ADM8614/ADM8615)
Watchdog function disable input (ADM8613/ADM8614 only)
Watchdog timeout extension input (ADM8614 only)
Active low, open-drain RESET output
Power supply glitch immunity
Available in a 1.46 mm × 0.96 mm WLCSP
Operational temperature range: −40°C to +85°C
GND
Figure 1. ADM8612 Functional Block Diagram
VCC
ADM8614
RESET
RESET
GENERATOR
VTH
WATCHDOG
DETECTOR
WDI
GND
WD_DIS
WDT_SEL
12782-002
Data Sheet
Ultralow Power Supervisory ICs with
Watchdog Timer and Manual Reset
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
Figure 2. ADM8614 Functional Block Diagram
Portable/battery-operated equipment
Microprocessor systems
Energy metering
Energy harvesting
GENERAL DESCRIPTION
The ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
are voltage supervisory circuits that monitor power supply voltage
levels and code execution integrity in microprocessor-based
systems. Apart from providing power-on reset signals, an onchip watchdog timer can reset the microprocessor if it fails to
strobe within a preset timeout period. A reset signal can also be
asserted by an external push-button through a manual reset input.
The ultralow power consumption of these devices makes them
suitable for power efficiency sensitive systems, such as batterypowered portable devices and energy meters.
The features of each member of the device family are shown in
Table 9. Each device subdivides into submodels with differences
in factory preset voltage monitoring threshold options. In the
range of 2 V to 4.63 V, 10 options are available for the ADM8611.
In the range of 2.32 V to 4.63 V, five options are available for
Rev. G
both the ADM8613 and ADM8614. A separate supply input
allows the ADM8612 and ADM8615 to monitor 20 different
low voltage levels from 0.5 V to 1.9 V. Not all device options are
available as standard models. See the Ordering Guide for details.
The ADM8611, ADM8612, ADM8613, and ADM8615 can
reset on demand through the manual reset input. The watchdog
function on the ADM8613, ADM8614, and ADM8615 monitors
the heartbeat of the microprocessor through the WDI pin. The
ADM8613 and ADM8614 have a watchdog disable input, which
allows the user to disable the watchdog function, if required. The
ADM8614 also has a watchdog timeout extension input, allowing
the watchdog timeout to be extended from 1.6 sec to 100 sec.
The ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
are available in a 6-ball, 1.46 mm × 0.96 mm WLCSP. These
devices are specified over the temperature range of −40°C to +85°C.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2015–2021 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Voltage Monitoring Input ......................................................... 12
Applications ....................................................................................... 1
VIN as an Adjustable Input....................................................... 12
Functional Block Diagrams ............................................................. 1
Transient Immunity ................................................................... 12
General Description ......................................................................... 1
Reset Output ............................................................................... 12
Revision History ............................................................................... 2
Manual Reset Input .................................................................... 13
Specifications..................................................................................... 3
Watchdog Timer ......................................................................... 13
Absolute Maximum Ratings............................................................ 5
Watchdog Timeout Select Input ............................................... 13
Thermal Resistance ...................................................................... 5
Typical Application Circuits ..................................................... 13
ESD Caution .................................................................................. 5
Low Power Design Techinques ................................................. 14
Pin Configurations and Function Descriptions ........................... 6
Device Model Options ................................................................... 15
Typical Performance Characteristics ............................................. 9
Outline Dimensions ....................................................................... 17
Theory of Operation ...................................................................... 12
Ordering Guide .......................................................................... 17
REVISION HISTORY
5/2021—Rev. F to Rev. G
Added VCC Slew Rate Considerations Section.......................... 12
2/2017—Rev. C to Rev. D
Changes to Ordering Guide .......................................................... 17
2/2018—Rev. E to Rev. F
Changes to General Description Section ...................................... 1
Added Note 1, Table 1 ...................................................................... 4
Changed Device Options Section to Model Options Section ...... 15
Changes to Model Options Section.............................................. 15
Added Table 15; Renumbered Sequentially ................................ 16
Changes to Ordering Guide .......................................................... 17
5/2016—Rev. B to Rev. C
Changes to MR Pull-Up Resistance Parameter, Table 1 ...............4
12/2017—Rev. D to Rev. E
Changes to Ordering Guide .......................................................... 17
12/2015—Rev. A to Rev. B
Changes to Watchdog Timeout Period Parameter, Table 1 .........4
Changes to Ordering Guide .......................................................... 17
4/2015—Rev. 0 to Rev. A
Changes to Reset Threshold Hysteresis Parameter, Table 1 ........3
1/2015—Revision 0: Initial Version
Rev. G | Page 2 of 17
Data Sheet
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
SPECIFICATIONS
VCC = 2 V to 5.5 V, VIN < VCC + 0.3 V, TA = −40°C to +85°C, unless otherwise noted. Typical values are at TA = 25°C.
Table 1.
Parameter
OPERATING VOLTAGE RANGE
ADM8611, ADM8613, ADM8614
ADM8612, ADM8615
UNDERVOLTAGE LOCKOUT (ADM8612,
ADM8615)
Input Voltage Rising
Input Voltage Falling
Hysteresis
INPUT CURRENT
VCC Quiescent Current
Symbol
VCC
Min
Typ
Max
Unit
Test Conditions/Comments
5.5
5.5
V
V
V
Guarantees valid RESET output
Guarantees valid RESET output
Guarantees RESET output low
1.95
V
V
mV
190
nA
110
nA
4
4
8.5
32
nA
nA
VTH − 1.3%
VTH − 1.3%
VTH − 1.4%
VTH − 1.6%
VTH − 1.6%
VTH − 1.7%
VTH − 1.8%
VTH − 1.8%
VTH − 1.9%
VTH − 1.9%
VTH − 2.0%
VTH − 2.1%
VTH − 2.1%
VTH − 2.2%
VTH
VTH
1.1
1
0.95
0.9
0.85
0.8
0.75
0.7
0.65
0.6
0.55
0.5
VTH + 1.3%
VTH + 1.3%
VTH + 1.4%
VTH + 1.6%
VTH + 1.6%
VTH + 1.7%
VTH + 1.8%
VTH + 1.8%
VTH + 1.9%
VTH + 1.9%
VTH + 2.0%
VTH + 2.1%
VTH + 2.1%
VTH + 2.2%
V
V
V
V
V
V
V
V
V
V
V
V
V
V
240
V
V
mV
ms
VTH > 1 V
VTH ≤ 1 V
170
0.9% × VTH
0.9% × VTH
10.3
200
18
26
37
μs
VCC falling with VTH × 10% overdrive
13.5
23
35
μs
VIN falling with VTH × 10% overdrive
13.5
23
32
μs
VCC falling, with VTH × 10% overdrive
13.5
21
27
μs
VIN falling with VTH × 10% overdrive
0.9
2
0.9
UVLORISE
UVLOFALL
UVLOHYS
1.6
90
ICC
92
VIN Average Input Current
RESET THRESHOLD VOLTAGE1
ADM8611, ADM8613, ADM8614
ADM8612, ADM8615
VTH
RESET THRESHOLD HYSTERESIS
ADM8611, ADM8613, ADM8614
ADM8612, ADM8615
VHYST
RESET TIMEOUT PERIOD
tRP
PROPAGATION DELAY
VCC to RESET
ADM8611, ADM8613, ADM8614
VIN to RESET
ADM8612, ADM8615
INPUT GLITCH REJECTION
VCC Glitch Rejection
ADM8611, ADM8613, ADM8614
VIN Glitch Rejection
ADM8612, ADM8615
VCC = 2 V to 5.5 V, RESET deasserts,
VWDI = VCC
VCC = 2 V to 5.5 V, RESET deasserts,
VWDI = VCC, TA = 25°C
VIN = 2 V, VCC = 5.5 V
VIN = 2 V, VCC = 2 V
Input falling
See Table 10 and Table 12
VTH ≥ 1.2 V, see Table 11
1.1 V threshold option
1 V threshold option
0.95 V threshold option
0.9 V threshold option
0.85 V threshold option
0.8 V threshold option
0.75 V threshold option
0.7 V threshold option
0.65 V threshold option
0.6 V threshold option
0.55 V threshold option
0.5 V threshold option
tPD_VCC
tPD_VIN
tGR_VCC
tGR_VIN
Rev. G | Page 3 of 17
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
Parameter
WATCHDOG INPUT, WDI (ADM8613,
ADM8614, ADM8615)
Watchdog Timeout Period1
ADM8613, ADM8615
ADM8614
Leakage Current
Input Threshold
High
Low
WDI Pulse Width
WDI Glitch Rejection
RESET OUTPUT
Output Voltage Low
Symbol
Min
Typ
Max
Unit
Test Conditions/Comments
tWD − 13%
tWD − 13%
tWD − 13%
tWD
tWD
tWD
tWD + 19%
tWD + 19%
tWD + 19%
5
sec
sec
sec
nA
Base period, WD_SEL low
Extended period, WD_SEL high
VWDI = VCC = 5.5 V
tWD
0.9
0.4
tWPR
tWPF
85
300
60
VRST_OL
Leakage Current
MANUAL RESET INPUT, MR (ADM8611,
ADM8612, ADM8613, ADM8615)
VIL
VIH
MR Minimum Input Pulse Width
MR Glitch Rejection
MR To Reset Delay
MR Pull-Up Resistance
WATCHDOG TIMEOUT DISABLE INPUT,
WD_DIS (ADM8613, ADM8614)
VIL
VIH
Leakage Current
Glitch Rejection
WATCHDOG TIMEOUT SELECTION
INPUT, WDT_SEL (ADM8614)
VIL
VIH
Leakage Current
1
Data Sheet
0.4
0.4
0.4
0.4
5
V
V
V
V
nA
0.4
V
V
μs
μs
μs
kΩ
0.9
1
tD_MR
300
0.4
0.65
600
900
0.4
0.9
−5
+5
0.1
0.4
0.9
−5
+5
Not all device options are available as standard models. See the Ordering Guide for details.
Rev. G | Page 4 of 17
V
V
ns
ns
ns
V
V
nA
μs
V
V
nA
High pulse
Low pulse
VCC > 4.25 V, ISINK = 6.5 mA
VCC > 2.5 V, ISINK = 6 mA
VCC > 1.2 V, ISINK = 4.6 mA
VCC > 0.9 V, ISINK = 0.9 mA
VRESET = VCC = 5.5 V
VWD_DIS = 0 V to VCC
VWDT_SEL = 0 V to VCC
Data Sheet
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 2.
Parameter
VCC
WD_DIS
RESET
VIN
MR
WDI
WDT_SEL
Input/Output Current
Storage Temperature Range
Operating Temperature Range
θJA is specified for a device soldered on an FR4 board with a
minimum footprint.
Rating
−0.3 V to +6 V
−0.3 V to +6 V
−0.3 V to +6 V
−0.3 V to +6 V
−0.3 V to VCC + 0.3 V
−0.3 V to VCC + 0.3 V
−0.3 V to VCC + 0.3 V
10 mA
−40°C to +150°C
−40°C to +85°C
Table 3.
Package Type
6-Ball WLCSP
ESD CAUTION
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. G | Page 5 of 17
θJA
105.6
Unit
°C/W
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
BALL A1
INDICATOR
1
2
VCC
GND
DNC
GND
MR
RESET
A
B
TOP VIEW
(BALL SIDE DOWN)
Not to Scale
DNC = DO NOT CONNECT.
DO NOT CONNECT TO THIS PIN.
12782-003
C
Figure 3. ADM8611 Pin Configuration
Table 4. ADM8611 Pin Function Descriptions
Pin No.
A1
Mnemonic
VCC
A2
B1
B2
C1
C2
GND
DNC
GND
MR
RESET
Description
Power Supply Input. The voltage on the VCC pin is monitored on the ADM8611. It is recommended to place a
0.1 μF decoupling capacitor as close as possible to the device between the VCC pin and the GND pin.
Ground. Both GND pins on the ADM8611 must be grounded.
Do Not Connect. Do not connect to this pin.
Ground. Both GND pins on the ADM8611 must be grounded.
Manual Reset Input, Active Low.
Active Low, Open-Drain RESET Output.
BALL A1
INDICATOR
1
2
VCC
GND
MR
GND
VIN
RESET
A
B
TOP VIEW
(BALL SIDE DOWN)
Not to Scale
12782-006
C
Figure 4. ADM8612 Pin Configuration
Table 5. ADM8612 Pin Function Descriptions
Pin No.
A1
Mnemonic
VCC
A2
B1
B2
C1
GND
MR
GND
VIN
C2
RESET
Description
Power Supply Input. The voltage on the VCC pin is not monitored on the ADM8612. It is recommended to place a
0.1 μF decoupling capacitor as close as possible to the device between the VCC pin and the GND pin.
Ground. Both GND pins on the ADM8612 must be grounded.
Manual Reset Input, Active Low.
Ground. Both GND pins on the ADM8612 must be grounded.
Low Voltage Monitoring Input. This separate supply input allows the ADM8612 to monitor low voltages on the
VIN pin to 0.5 V.
Active Low, Open-Drain RESET Output.
Rev. G | Page 6 of 17
Data Sheet
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
BALL A1
INDICATOR
1
2
VCC
GND
WDI
WD_DIS
MR
RESET
A
B
TOP VIEW
(BALL SIDE DOWN)
Not to Scale
12782-004
C
Figure 5. ADM8613 Pin Configuration
Table 6. ADM8613 Pin Function Descriptions
Pin No.
A1
Mnemonic
VCC
A2
B1
B2
GND
WDI
WD_DIS
C1
C2
MR
RESET
Description
Power Supply Input. The voltage on the VCC pin is monitored on the ADM8613. It is recommended to place a
0.1 μF decoupling capacitor as close as possible to the device between the VCC pin and the GND pin.
Ground.
Watchdog Timer Input.
Watchdog Function Disable Input. Tie this pin high to disable the watchdog function of the device. Connect
this pin to ground if it is not used.
Manual Reset Input, Active Low.
Active Low, Open-Drain RESET Output.
BALL A1
INDICATOR
1
2
VCC
GND
WDI
WD_DIS
A
B
WDT_SEL RESET
TOP VIEW
(BALL SIDE DOWN)
Not to Scale
12782-007
C
Figure 6. ADM8614 Pin Configuration
Table 7. ADM8614 Pin Function Descriptions
Pin No.
A1
Mnemonic
VCC
A2
B1
B2
GND
WDI
WD_DIS
C1
WDT_SEL
C2
RESET
Description
Power Supply Input. The voltage on the VCC pin is monitored on the ADM8614. It is recommended to place a
0.1 μF decoupling capacitor as close as possible to the device between the VCC pin and the GND pin.
Ground.
Watchdog Timer Input.
Watchdog Function Disable Input. Tie this pin high to disable the watchdog function of the device. Connect this
pin to ground if it is not used.
Watchdog Timeout Selection Input. Pull this pin high to extend the watchdog timeout period of the ADM8614 to
100 sec. Pull this pin low to return the watchdog timeout period to its base value. Toggling WDT_SEL resets the
watchdog timer.
Active Low, Open-Drain RESET Output.
Rev. G | Page 7 of 17
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
Data Sheet
BALL A1
INDICATOR
1
2
VCC
GND
MR
WDI
VIN
RESET
A
B
TOP VIEW
(BALL SIDE DOWN)
Not to Scale
12782-005
C
Figure 7. ADM8615 Pin Configuration
Table 8. ADM8615 Pin Function Descriptions
Pin No.
A1
Mnemonic
VCC
A2
B1
B2
C1
GND
MR
WDI
VIN
C2
RESET
Description
Power Supply Input. The voltage on the VCC pin is not monitored on the ADM8615. It is recommended to place a
0.1 μF decoupling capacitor as close as possible to the device between the VCC pin and the GND pin.
Ground.
Manual Reset Input, Active Low.
Watchdog Timer Input.
Low Voltage Monitoring Input. This separate supply input allows the ADM8615 to monitor low voltages on the VIN
pin to 0.5 V.
Active Low, Open-Drain RESET Output.
Rev. G | Page 8 of 17
Data Sheet
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
TYPICAL PERFORMANCE CHARACTERISTICS
600
120
VCC = 2V
VCC = 3.3V
VCC = 5.5V
115
500
110
105
400
ICC (nA)
ICC (nA)
100
95
300
90
200
85
80
100
0
10
20
30
40
50
60
70
0
12782-008
70
–40 –30 –20 –10
80
TEMPERATURE ( °C)
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
LOGIC INPUT PIN VOLTAGE (V)
12782-111
75
Figure 11. Supply Current (ICC) vs. Logic Input Pin Voltage, with the Exception
of the MR Pin
Figure 8. Supply Current (ICC) vs. Temperature
3.0
200
180
2.5
160
VCC FALLING
140
120
ICC (nA)
ICC (µA)
2.0
1.5
VCC RISING
1.0
100
80
60
40
0.5
0.5
1.0
1.5
2.0
2.5
SUPPLY VOLTAGE (V)
0
12782-009
0
0
200
600
800
1000
Figure 12. Average Supply Current (ICC) vs. WDI Toggling Frequency, Using a
Square Pulse Signal with a Duty Cycle of 50%
Figure 9. Supply Current (ICC) vs. Supply Voltage, VCC < 2V
8
120
IVIN, VCC = 0V
IVIN, VCC = 2V
ICC, VCC = 2V
7
110
INPUT CURRENT (µA)
6
100
90
80
5
4
3
2
1
0
70
60
2.0
2.5
3.0
3.5
4.0
4.5
5.0
SUPPLY VOLTAGE (V)
5.5
–2
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
VIN (V)
Figure 10. Supply Current (ICC) vs. Supply Voltage
Figure 13. VIN Pin and VCC Pin Input Current vs. VIN
Rev. G | Page 9 of 17
5.5
12782-013
–1
12782-010
ICC (nA)
400
WDI TOGGLING FREQUENCY (Hz)
12782-112
20
0
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
5
4
3
2
1
10
20
30
40
50
60
70
80
TEMPERATURE (°C)
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
–40 –30 –20 –10
12782-014
0
1.3
1.010
1.005
1.000
0.995
0.990
0.985
0.980
–40
–20
0
20
40
30
40
50
60
70
80
90
1.5
= 0.6V
= 2.0V
= 3.3V
= 4.7V
NORMALIZED WATCHDOG TIMEOUT PERIOD
1.015
20
Figure 17. Normalized Reset Timeout Period vs. Temperature
60
80
TEMPERATURE (°C)
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
–40
12782-115
NORMALIZED FALLING THRESHOLD
VTH
VTH
VTH
VTH
10
TEMPERATURE (°C)
Figure 14. VIN Leakage Current vs. Temperature
1.020
0
12782-117
6
0
–40 –30 –20 –10
1.4
NORMALIZED RESET TIMEOUT PERIOD
7
VIN LEAKAGE CURRENT (nA)
1.5
VCC = 5.5V
VCC = 3.3V
VCC = 2V
–20
0
20
40
60
12782-118
8
Data Sheet
80
TEMPERATURE (°C)
Figure 18. Normalized Watchdog Timeout Period vs. Temperature
Figure 15. Normalized Falling Threshold vs. Temperature
0.30
350
0.25
300
RESET PIN LEAKAGE (nA)
200
150
100
0.15
0.10
0.05
0
–0.05
–0.10
50
1
10
100
INPUT OVERDRIVE (mV)
Figure 16. Maximum Transient Duration vs. Input Overdrive,
VCC and VIN Falling
–0.20
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
RESET PIN VOLTAGE (V)
Figure 19. RESET Pin Leakage vs. RESET Pin Voltage
Rev. G | Page 10 of 17
5.5
12782-019
0
–0.15
12782-016
TRANSIENT DURATION (µs)
0.20
250
Data Sheet
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
0.50
RPULLUP = 10kΩ
RPULLUP = 100kΩ
0.45
RESET PIN VOLTAGE (V)
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0
0.5
1.0
1.5
2.0
2.5
12782-020
0
12782-022
0.05
3.0
VCC (V)
Figure 22. RESET Timeout Delay With VCC and VIN Rising
Figure 20. RESET Pin Voltage vs. Voltage on VCC
(with the RESET Pin Pulled Up to the VCC Pin Through RPULLUP)
2.0
1.6
1.4
1.2
1.0
0.8
0.6
VCC
VCC
VCC
VCC
0.2
0
1
2
3
4
5
6
7
8
= 0.9V
= 1.2V
= 2.5V
= 4.25V
9 10 11 12 13 14 15 16 17 18 19 20
ISINK (mA)
12782-023
0.4
12782-021
RESET OUTPUT LOW VOLTAGE (V)
1.8
Figure 21. RESET Output Low Voltage (VRST_OL) vs. Sink Current (ISINK)
Figure 23. RESET Timeout Delay With VCC and VIN Falling
Rev. G | Page 11 of 17
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
Data Sheet
THEORY OF OPERATION
The ADM8611/ADM8612/ADM8613/ADM8614/ADM8615 low
power voltage supervisors protect the integrity of system
operation by ensuring the proper operation during power-up,
power-down, and brownout conditions. These devices monitor
the input voltage level and compare it against an internal reference.
The RESET output asserts whenever the monitored voltage level
is below the reference threshold, keeping the processor in a reset
state. The RESET output deasserts if the monitored voltage rises
above the threshold reference for a minimum period, the active
reset timeout period. This ensures that the supply voltage for
the processor is raised to an adequate level and stable before
exiting reset.
The ultralow supply current makes the ADM8611/ADM8612/
ADM8613/ADM8614/ADM8615 devices particularly suitable
for use in low power, portable equipment.
VCC
It is recommended to place a 0.1 μF decoupling capacitor as close
as possible to the device between the VCC pin and the GND pin.
VCC Slew Rate Consideration
A fast VCC ramp (μs range) on power-up can cause the device
to behave in an irregular manner. In applications where a high
slew rate on VCC is possible, for example, powering up using a
battery pack, it is recommended that an RC filter is used to reduce
the slew rate. RC combinations of 3.3 kΩ + 2.2 μF and 1 kΩ + 10 μF
have been tested and identified as safe options.
VIN AS AN ADJUSTABLE INPUT
Due to the low leakage nature of the VIN pin, the ADM8612 or
ADM8615 can be used as devices with an adjustable threshold. Use
an external resistor divider circuit to program the desired voltage
monitoring threshold based on the VIN threshold, as shown in
Figure 27.
3.3V
ADM8611
RESET
12V
RESET
GENERATOR
VTH
VIO
VCC
RESET
ADM8615
VIN
DEBOUNCE
12782-127
Figure 24. ADM8611 Functional Block Diagram
Figure 27. ADM8615 Typical Application Circuit
VCC
TRANSIENT IMMUNITY
ADM8613
To avoid unnecessary resets caused by fast power supply transients,
an input glitch filter is added to the VCC pin of the ADM8611/
ADM8613/ADM8614 and the VIN pin of the ADM8612 and
ADM8615 to filter out the transient glitches on these pins.
RESET
RESET
GENERATOR
DEBOUNCE
GND
WATCHDOG
DETECTOR
WDI
Figure 16 shows the comparator overdrive (that is, the maximum
magnitude of negative going pulses with respect to the typical
threshold) vs. the pulse duration without a reset.
12782-025
MR
WD_DIS
Figure 25. ADM8613 Functional Block Diagram
RESET OUTPUT
VCC
The ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
devices all have an active low, open-drain reset output. For the
ADM8611/ADM8613/ADM8614, the state of the output is
guaranteed to be valid as soon as VCC is greater than 0.9 V. For
the ADM8612 and ADM8615, the output is guaranteed to be
held low from when VCC = 0.9 V to when the device exits ULVO.
ADM8615
RESET
VIN
MR
DEBOUNCE
WATCHDOG
DETECTOR
GND
WDI
12782-026
RESET
GENERATOR
VTH
OUTPUT
MR GND
GND
VTH
MICROPROCESSOR
12782-024
MR
WDI
RESET
Figure 26. ADM8615 Functional Block Diagram
VOLTAGE MONITORING INPUT
The VCC pin of the ADM8611/ADM8613/ADM8614 acts as
both a device power input node and a voltage monitoring input
node. The ADM8612 uses separate pins for supply and voltage
monitoring to achieve a low voltage monitoring threshold to 0.5 V.
When the monitored voltage falls below its associated threshold,
RESET is asserted within 23 μs to 26 μs (typical). Asserting RESET
this quickly ensures that the entire system can be reset at once
before any part of the system voltage falls below its recommended
operating voltage. This system reset can avoid dangerous and/or
erroneous operation of a microprocessor-based system.
Rev. G | Page 12 of 17
Data Sheet
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
MANUAL RESET INPUT
WATCHDOG TIMEOUT SELECT INPUT
The ADM8611, ADM8612, ADM8613, and ADM8615 feature a
manual reset input (MR). Drive MR low to assert the reset output.
When MR transitions from low to high, the reset remains asserted
for the duration of the reset timeout period before deasserting.
The MR input has a 600 kΩ internal pull-up resistor so that the
input is always high when unconnected. To drive the MR input,
use an external signal or a push-button switch to ground; debounce
circuitry is integrated on-chip for this purpose. Noise immunity is
provided on the MR input, and fast, negative going transients of
up to 0.4 μs (typical) are ignored. If required, a 0.1 μF capacitor
between the MR pin and ground provides additional noise
immunity.
Pulling the watchdog timeout select input (WDT_SEL) on the
ADM8614 high allows the device to extend its watchdog timeout
period from 1.6 sec (typical) to 100 sec (typical). This function
allows processors to have a long initialization time during startup.
The long timeout period also enables the processor to stay in
low power mode for a long period and work only intermittently,
reducing overall system power consumption.
TYPICAL APPLICATION CIRCUITS
3.3V
RESET
ADM8611
VTH
tRP
RESET
MICROPROCESSOR
GND
tRP
RESET
12782-029
VCC
VCORE
VCC
MR
Figure 30. ADM8611 Typical Application Circuit
0.8V
3.3V
12782-027
VIO
VCC
Figure 28. Manual Reset Timing
RESET
WATCHDOG TIMER
ADM8612
In addition to logic transitions on WDI, the watchdog timer
is also cleared by a reset assertion caused by an undervoltage
condition on the VCC pin, WDT_SEL toggling, or MR being
pulled low. When RESET is asserted, the watchdog timer is
cleared and does not begin counting again until the RESET
output is deasserted. The watchdog timer can be disabled by
driving the watchdog disable input (WD_DIS) high.
0V
tRP
tWD
tRP
12782-028
RESET
GND
WDI
0V
MICROPROCESSOR
MR
Figure 31. ADM8612 Typical Application Circuit
2.5V
VCC
RESET
ADM8613
WDI
MR
RESET
VIO
MICROPROCESSOR
OUTPUT
WD_DIS
GND
Figure 32. ADM8613 Typical Application Circuit
2.5V
VCC
RESET
ADM8614
VTH
VCC
VIN
12782-030
The ADM8613/ADM8614/ADM8615 feature a watchdog timer
that monitors microprocessor activity. A timer circuit is cleared
with every low to high or high to low logic transition on the watchdog input pin (WDI), which detects pulses as short as 85 ns. If
the timer counts through the preset watchdog timeout period (tWD),
a RESET output is asserted. The microprocessor must toggle the
WDI pin to avoid being reset. Failure of the microprocessor to
toggle the WDI pin within the timeout period indicates a code
execution error, and the reset pulse generated restarts the
microprocessor in a known state.
VCORE
INPUT
12782-031
tD_MR
RESET
VIO
MICROPROCESSOR
WDI
WD_DIS
OUTPUT
WDT_SEL
GND
OUTPUT
OUTPUT
Figure 33. ADM8614 Typical Application Circuit
Figure 29. Watchdog Timer Timing
Rev. G | Page 13 of 17
12782-032
MR EXTERNALLY
DRIVEN LOW
MR
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
LOW POWER DESIGN TECHINQUES
With their ultralow power consumption level, the ADM8611/
ADM8612/ADM8613/ADM8614/ADM8615 are ideal for batterypowered, low power applications where every bit of power matters.
In addition to using low power ICs, good circuit design practices
can help the user further reduce the overall system power loss.
Digital Inputs
and increase the bias current (ICC) of the ADM8613/ADM8614/
ADM8615. To minimize the power loss in this setup, use short
positive pulses to drive the WDI pin. The ideal pulse width is as
small as possible but greater than the required minimum pulse
width of the WDI input. One pulse within the watchdog timeout
period is sufficient to prevent the watchdog timer from generating
a reset output.
HIGH
WDI Input
When the watchdog input (WDI) is driven by a push-pull
input/output with a logic high level near the VCC level of the
ADM8613/ADM8614/ADM8615, neither a high nor a low input
logic causes the system to consume additional current. To reduce
the total current consumption, increase the speed of the input
transition to the number of transitions. One high to low or low
to high transition within the watchdog timeout period is sufficient
to prevent the watchdog timer from generating a reset output.
If the watchdog input is driven by a push-pull output with a logic
high level near the minimum logic high specification of the digital
input, then a logic high input may cause CMOS shoot through
1.5V
VIO
VCC
WDI
PUSH-PULL
OUTPUT
ADM8614
WATCHDOG
OUTPUT
MICROPROCESSOR
Figure 34. Using a Push-Pull Output with a Lower Logic High Level to VCC,
Driving the WDI Pin with Short Positive Pulse to Reduce ICC
Similarly, if an open-drain input/output with a pull-up resistor
to VCC is used to drive WDI, a logic low input causes additional
current flowing through the pull-up resistor. A short negative
pulse technique can minimize the long-term current consumption.
2.5V
VCC
WDI
ADM8614
HIGH
LOW
OPEN-DRAIN
OUTPUT
WATCHDOG
OUTPUT
MICROPROCESSOR
12782-036
If the digital input does not need to be toggled in a particular
design, tie it directly to the VCC or GND pin of the device.
Push-pull outputs with logic high levels close to the VCC of the
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615 are
the ideal choice for driving the digital signal line.
Using push-pull outputs with a logic high level near the
minimum logic high specification of the digital input is
usually not recommended. One exception is if the input is
required to be driven high only infrequently for a relatively
short period.
Open-drain outputs with a pull-up resistor to VCC can be
used to drive digital signal lines. Open-drain outputs are
best suited for driving lines that are required to be driven
low only infrequently for a relatively short period.
The leakage current on both the digital input and the opendrain output determines the size of the pull-up resistor
needed and, in turn, decides the power loss through the
resistor while driving the input low.
The MR pin on the ADM8611, ADM8612, ADM8613, and
ADM8615 features an internal pull-up resistor. The infrequent
usage of this pin makes its power loss while driven to logic
low negligible.
LOW
2.5V
12782-033
The digital inputs of the ADM8611/ADM8612/ADM8613/
ADM8614/ADM8615 voltage supervisors are designed with
CMOS technology to minimize power consumption. The nature of
the CMOS structure leads to an increase of the device ICC, while
the voltage level on the input approaches its undefined logic range,
as shown in Figure 11. To minimize this effect, follow these
recommendations:
Data Sheet
Figure 35. Short Negative Pulse on the WDI Pin to Reduce Leakage Current
Through the Pull-Up Resistor
WD_DIS Input
For the ADM8613 and ADM8614, the watchdog disable input
(WD_DIS) disables the watchdog function during system
prototyping or during power-up to allow extra time for
processor initialization.
To disable the watchdog timer function during power-up after a
reset deassertion, the processor configures its input/output and
drives WD_DIS high within the watchdog timeout period. If
there is not enough time to configure the input/output or if an
open-drain input/output is used to drive WD_DIS, an external
pull-up resistor is required to keep the watchdog function disabled
during power-up. Extra current is consumed through the pull-up
resistor to enable the watchdog function. The leakage current
on both WD_DIS and the input/output that drives it determines
the size of the pull-up resistor needed and, in turn, determines
the power loss through the resistor while driving the input low.
Rev. G | Page 14 of 17
Data Sheet
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
DEVICE MODEL OPTIONS
The ADM8611/ADM8612/ADM8613/ADM8614/ADM8615 include many device options; however, not all options are released for sale.
Released options are called standard models and are listed in the Ordering Guide. For the most up to date list of standard models, refer to
the Analog Devices website at www.analog.com/supervisory. Contact an Analog Devices sales representative for information on nonstandard
models, and be aware that samples and production units have long lead times.
Table 9. Selection Table
Device
Number
ADM8611
ADM8612
ADM8613
ADM8614
ADM8615
Low Voltage
Monitoring
No
Yes
No
No
Yes
Manual
Reset
Yes
Yes
Yes
No
Yes
Watchdog
Timer
No
No
Yes
Yes
Yes
Watchdog Disable
Input
No
No
Yes
Yes
No
Watchdog Timeout
Selection Input
No
No
No
Yes
No
Table 10. ADM8611 VCC Reset Threshold Voltage (VTH) Options (TA = −40°C to +85°C)
Reset Threshold Number
200
220
232
263
280
293
300
308
440
463
Min
1.974
2.171
2.290
2.596
2.764
2.892
2.961
3.040
4.343
4.570
Typ
2
2.2
2.32
2.63
2.8
2.93
3
3.08
4.4
4.63
Max
2.026
2.229
2.350
2.664
2.836
2.968
3.039
3.120
4.457
4.690
Unit
V
V
V
V
V
V
V
V
V
V
Table 11. ADM8612 and ADM8615 VIN Reset Threshold Voltage (VTH) Options (TA = −40°C to +85°C)
Reset Threshold Number
050
055
060
065
070
075
080
085
090
095
100
110
120
130
140
150
160
170
180
190
Min
0.489
0.538
0.588
0.637
0.686
0.736
0.785
0.835
0.885
0.935
0.984
1.084
1.184
1.283
1.382
1.481
1.579
1.678
1.777
1.875
Rev. G | Page 15 of 17
Typ
0.5
0.55
0.6
0.65
0.7
0.75
0.8
0.85
0.9
0.95
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
Max
0.511
0.562
0.612
0.663
0.714
0.764
0.815
0.865
0.915
0.965
1.016
1.116
1.216
1.317
1.418
1.520
1.621
1.722
1.823
1.925
Unit
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
Data Sheet
Table 12. ADM8613 and ADM8614 VCC Reset Threshold Voltage (VTH) Options (TA = −40°C to +85°C)
Reset Threshold Number
232
263
293
308
463
Min
2.290
2.596
2.892
3.040
4.570
Typ
2.32
2.63
2.93
3.08
4.63
Max
2.350
2.664
2.968
3.120
4.690
Unit
V
V
V
V
V
Table 13. ADM8613 and ADM8615 Watchdog Timeout Options (TA = −40°C to +85°C)
Watchdog Timeout Period Code
Y
Z
Min
1.4
22.3
Typ
1.6
25.6
Max
1.9
30.5
Unit
sec
sec
Test Condition/Comments
WD_DIS low
WD_DIS low
Unit
sec
sec
Test Condition/Comments
WD_DIS low, WDT_SEL low
WD_DIS low, WDT_SEL high
Table 14. ADM8614 Watchdog Timeout Options (TA = −40°C to +85°C)
Watchdog Timeout Period Code
Y
Min
1.4
87
Typ
1.6
100
Max
1.9
119
Table 15. Standard Models
Reset Threshold (V)
2.63
2.93
1.1
2.32
2.32
2.63
1
0.5
Watchdog Timeout (sec)
N/A
N/A
N/A
1.6
25.6
1.6
1.6
25.6
ADM861_ _ _ _ _A_ _Z-R7
GENERIC NUMBER
(1 TO 5)
WATCHDOG TIMEOUT PERIOD CODE
Y:1.6s (TYP)
Z: 25.6s (TYP)
N: NO WATCH DOG FUNCTION
RESET THRESHOLD NUMBER
(050 TO 463)
PACKING MATERIAL
R7 = 7" TAPE AND REEL
(3000 PIECE QUANTITY)
Z = LEAD-FREE
PACKAGE DESIGNATON
CB: WLCSP
TEMPERATURE RANGE
A: –40°C TO +85°C
Figure 36. Ordering Code Structure
Rev. G | Page 16 of 17
12782-037
Model
ADM8611N263ACBZ-R7
ADM8611N293ACBZ-R7
ADM8612N110ACBZ-R7
ADM8613Y232ACBZ-R7
ADM8613Z232ACBZ-R7
ADM8614Y263ACBZ-R7
ADM8615Y100ACBZ-R7
ADM8615Z050ACBZ-R7
Data Sheet
ADM8611/ADM8612/ADM8613/ADM8614/ADM8615
OUTLINE DIMENSIONS
1.000
0.960
0.920
BOTTOM VIEW
(BALL SIDE UP)
2
1
A
BALL A1
IDENTIFIER
1.500
1.460
1.420
1.00
REF
0.50
BSC
TOP VIEW
(BALL SIDE DOWN)
0.660
0.600
0.540
B
C
0.50 BSC
0.390
0.360
0.330
SIDE VIEW
0.360
0.320
0.280
PKG-003299
SEATING
PLANE
0.270
0.240
0.210
08-25-2014-A
COPLANARITY
0.04
Figure 37. 6-Ball Wafer Level Chip Scale Package [WLCSP]
(CB-6-17)
Dimensions shown in millimeters
ORDERING GUIDE
Model1, 2, 3
ADM8611N263ACBZ-R7
ADM8611N293ACBZ-R7
ADM8612N110ACBZ-R7
ADM8613Y232ACBZ-R7
ADM8613Z232ACBZ-R7
ADM8614Y263ACBZ-R7
ADM8615Y100ACBZ-R7
ADM8615Z050ACBZ-R7
ADM8611-EVALZ
ADM8612-EVALZ
ADM8613-EVALZ
ADM8614-EVALZ
ADM8615-EVALZ
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
6-Ball Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Ball Wafer Level Chip Scale Package [WLCSP]
Evaluation Board
Evaluation Board
Evaluation Board
Evaluation Board
Evaluation Board
1
Package Option
CB-6-17
CB-6-17
CB-6-17
CB-6-17
CB-6-17
CB-6-17
CB-6-17
CB-6-17
Marking Code
DJ
ES
DV
DQ
ED
DR
DS
EG
Z = RoHS Compliant Part.
The ADM8611/ADM8612/ADM8613/ADM8614/ADM8615 include many device options; however, not all options are released for sale. Released options are called
standard models and are listed in the Ordering Guide. For the most up to date list of standard models, refer to the Analog Devices website at www.analog.com/supervisory.
Contact an Analog Devices sales representative for information on nonstandard models, and be aware that samples and production units have long lead times.
3
If ordering nonstandard models, complete the ordering code shown in Figure 36 by inserting the model number, reset threshold, and watchdog timeout.
2
©2015–2021 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12782-5/21(G)
Rev. G | Page 17 of 17
工商网监
湘ICP备2023018690号
