5 kV RMS/3.75 kV RMS, 600 Mbps,
Dual-Channel LVDS Isolators
ADN4650/ADN4651/ADN4652
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
APPLICATIONS
VIN1
ADN4650
ISOLATION
BARRIER
LDO
VDD1
LDO
VDD2
DIN1+
DOUT1+
DIN1–
DOUT1–
LVDS
DIGITAL ISOLATOR
LVDS
DOUT2+
DIN2–
DOUT2–
GND1
GND2
Figure 1.
VIN1
ADN4651
VIN2
ISOLATION
BARRIER
LDO
VDD1
LDO
VDD2
DIN1+
DOUT1+
DIN1–
DOUT1–
LVDS
DIGITAL ISOLATOR
LVDS
DIN2+
DOUT2–
DIN2–
GND1
GND2
Figure 2.
VIN1
ADN4652
VDD1
LDO
VIN2
ISOLATION
BARRIER
LDO
VDD2
DIN1+
DIN1–
DOUT1–
LVDS
DIGITAL ISOLATOR
Multiple channel configurations are offered, and the LVDS receivers
on the ADN4651/ADN4652 include a fail-safe mechanism to
LVDS
DIN2+
DOUT2+
DIN2–
DOUT2–
GND1
The devices integrate Analog Devices, Inc., iCoupler® technology,
enhanced for high speed operation, to provide galvanic isolation of
the TIA/EIA-644-A compliant LVDS drivers and receivers.
This technology allows drop-in isolation of an LVDS signal
chain.
13677-001
DOUT2+
GENERAL DESCRIPTION
The ADN4650/ADN4651/ADN46521 are signal isolated, low
voltage differential signaling (LVDS) buffers that operate at up
to 600 Mbps with very low jitter.
13677-101
DIN2+
DOUT1+
Analog front-end (AFE) isolation
Data plane isolation
Isolated high speed clock and data links
Isolated serial peripheral interface (SPI) over LVDS
1
VIN2
GND2
13677-103
5 kV rms/3.75 kV rms LVDS isolator
Complies with TIA/EIA-644-A LVDS standard
Multiple dual-channel configurations
Up to 600 Mbps switching with low jitter
4.5 ns maximum propagation delay
151 ps maximum peak-to-peak total jitter at 600 Mbps
100 ps maximum pulse skew
600 ps maximum part to part skew
2.5 V or 3.3 V supplies
−75 dBc power supply ripple rejection and glitch immunity
±8 kV IEC 61000-4-2 ESD protection across isolation barrier
High common-mode transient immunity: >25 kV/μs
Passes EN55022 Class B radiated emissions limits with
600 Mbps PRBS
Safety and regulatory approvals (20-lead SOIC package)
UL: 5000 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice 5A
VDE certificate of conformity
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
VIORM = 424 V peak
Fail-safe output high for open, short, and terminated input
conditions (ADN4651/ADN4652)
Operating temperature range: −40°C to +125°C
Choice of package and isolation options
3.75 kV rms in highly integrated 20-lead SSOP
5 kV rms in 20-lead SOIC with 7.8 mm creepage/clearance
Figure 3.
ensure a Logic 1 on the corresponding LVDS driver output
when the inputs are floating, shorted, or terminated, but not
driven.
For high speed operation with low jitter, the LVDS and isolator
circuits rely on a 2.5 V supply. An integrated on-chip low dropout
regulator (LDO) can provide the required 2.5 V from an external
3.3 V power supply. The devices are fully specified over a wide
industrial temperature range and are available in a 20-lead,
wide body SOIC package with 5 kV rms isolation or a 20-lead
SSOP package with 3.75 kV rms isolation.
Protected by U.S. Patents 5,952,849; 6,873,065; 6,903,578; and 7,075,329. Other patents are pending.
Rev. E
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2015–2019 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADN4650/ADN4651/ADN4652
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Thermal Resistance .......................................................................8
Applications ....................................................................................... 1
ESD Caution...................................................................................8
General Description ......................................................................... 1
Pin Configurations and Function Descriptions ............................9
Functional Block Diagrams ............................................................. 1
Typical Performance Characteristics ........................................... 12
Revision History ............................................................................... 2
Test Circuits and Switching Characteristics................................ 17
Specifications..................................................................................... 3
Theory of Operation ...................................................................... 18
Receiver Input Threshold Test Voltages .................................... 4
Truth Table and Fail-Safe Receiver .......................................... 18
Timing Specifications .................................................................. 4
Isolation ....................................................................................... 19
Insulation and Safety Related Specifications ............................ 5
PCB Layout ................................................................................. 19
Package Characteristics ............................................................... 6
Magnetic Field Immunity.......................................................... 19
Regulatory Information ............................................................... 6
Insulation Lifetime ..................................................................... 20
DIN V VDE V 0884-10 (VDE V 0884-10) Insulation
Characteristics .............................................................................. 6
Applications Information .............................................................. 22
Recommended Operating Conditions ...................................... 7
Ordering Guide .......................................................................... 24
Outline Dimensions ....................................................................... 24
Absolute Maximum Ratings............................................................ 8
REVISION HISTORY
6/2019—Rev. D to Rev. E
Changes to Features Section............................................................ 1
Changed UL (Pending) Column to UL Column, CSA (Pending)
Column to CSA Column, VDE (Pending) Column to VDE
Column, Table 7, and DIN V VDE V 0884-10 (VDE V 0884-110)
Insulation Characteristics (Pending) Section to DIN V VDE V
0884-10 (VDE V 0884-110) Insulation Characteristics Section...... 6
1/2017—Rev. C to Rev. D
Changes to Ordering Guide .......................................................... 24
9/2016—Rev. B to Rev. C
Added 20-Lead SSOP .................................................... Throughout
Changes to Title, Features Section, and General Description .... 1
Added Table 5; Renumbered Sequentially .................................... 5
Change to Figure 5 ........................................................................... 7
Changes to PCB Layout Section ................................................... 19
Changes to Surface Tracking Section ........................................... 20
Updated Outline Dimensions ....................................................... 24
Changes to Ordering Guide .......................................................... 24
4/2016—Rev. A to Rev. B
Added ADN4652 ................................................................ Universal
Changes to Features Section and General Description Section....... 1
Added Figure 3; Renumbered Sequentially .................................. 1
Changes to Supply Current Parameter, Table 1 ............................ 3
Changes to Skew Parameter and Fail-Safe Delay Parameter,
Table 3 .................................................................................................4
Changes to Table 12 ..........................................................................9
Moved Figure 7 ............................................................................... 10
Added Table 13 ............................................................................... 10
Added Figure 8 and Table 14, Renumbered Sequentially ......... 11
Changes to PCB Layout Section ................................................... 19
Changes to Ordering Guide .......................................................... 24
2/2016—Rev. 0 to Rev. A
Added ADN4650 ................................................................ Universal
Changes to Features Section and General Description Section ........ 1
Added Figure 1; Renumbered Sequentially ...................................1
Changes to Supply Current Parameter, Table 1 .............................3
Changes to Skew Parameter and Fail-Safe Delay Parameter,
Table 3 .................................................................................................4
Added Figure 5...................................................................................9
Changes to Table 12 ..........................................................................9
Changes to Figure 30 Caption and Figure 31 Caption .............. 14
Change to Figure 34 ....................................................................... 15
Changes to Truth Table and Fail-Safe Receiver Section ............ 16
Added Table 13; Renumbered Sequentially ................................ 16
Change to Applications Information Section ............................. 20
Added Figure 41 ............................................................................. 20
Changes to Ordering Guide .......................................................... 22
11/2015—Revision 0: Initial Version
Rev. E | Page 2 of 25
Data Sheet
ADN4650/ADN4651/ADN4652
SPECIFICATIONS
For all minimum/maximum specifications, VDD1 = VDD2 = 2.375 V to 2.625 V, TA = TMIN to TMAX, unless otherwise noted. For all typical
specifications, VDD1 = VDD2 = 2.5 V, TA = 25°C.
Table 1.
Parameter
INPUTS (RECEIVERS)
Input Threshold
High
Low
Symbol
Min
Typ
100
0.5|VID|
−5
|VOD|
|ΔVOD|
VOS
ΔVOS
VOS(PP)
IOS
250
310
1.125
1.17
Differential Output
Capacitance1
POWER SUPPLY
Supply Current
COUTx±
1
2
Test Conditions/Comments
mV
V
µA
pF
See Figure 36 and Table 2
See Figure 36 and Table 2
DINx± = VDD or 0 V, other input = 1.2 V, VDD = 2.5 V or 0 V
DINx± = 0.4 sin(30 × 106πt) V + 0.5 V, other input = 1.2 V
450
50
1.375
50
150
−20
12
mV
mV
V
mV
mV
mA
mA
pF
See Figure 34 and Figure 35, RL = 100 Ω
See Figure 34 and Figure 35, RL = 100 Ω
See Figure 34, RL = 100 Ω
See Figure 34, RL = 100 Ω
See Figure 34, RL = 100 Ω
DOUTx± = 0 V
|VOD| = 0 V
DOUTx± = 0.4 sin(30 × 106πt) V + 0.5 V, other input =
1.2 V, VDD1 or VDD2 = 0 V
55
80
65
72
3.6
mA
mA
mA
mA
V
No output load, inputs with 100 Ω, no applied |VID|
All outputs loaded, RL = 100 Ω, f = 300 MHz
No output load, inputs with 100 Ω, |VID| = 200 mV
All outputs loaded, RL = 100 Ω, f = 300 MHz
No external supply on VDD1 or VDD2
2.625
V
2
5
IDD1, IIN1,
IDD2, or IIN2
VIN1 or
VIN2
VDD1 or
VDD2
PSRR
3.0
58
50
60
3.3
2.375
2.5
|CM|
25
ADN4650 Only
COMMON-MODE TRANSIENT
IMMUNITY 2
mV
mV
2.4 − 0.5|VID|
+5
ADN4651/ADN4652 Only
Power Supply Ripple Rejection,
Phase Spur Level
100
−100
|VID|
VIC
IIH, IIL
CINx±
LDO Output Range
Unit
See Figure 36 and Table 2
VTH
VTL
Differential Input Voltage
Input Common-Mode Voltage
Input Current
Differential Input Capacitance1
OUTPUTS (DRIVERS)
Differential Output Voltage
VOD Magnitude Change
Offset Voltage
VOS Magnitude Change
VOS Peak-to-Peak1
Output Short-Circuit Current
LDO Input Range
Max
−75
dBc
50
kV/µs
Phase spur level on DOUTx± with 300 MHz clock on
DINx± and applied ripple of 100 kHz, 100 mV p-p on
a 2.5 V supply to VDD1 or VDD2
VCM = 1000 V, transient magnitude = 800 V
These specifications are guaranteed by design and characterization.
|CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining any DOUTx+/DOUTx− pin in the same state as the corresponding DINx+/DINx−
pin (no change on output), or producing the expected transition on any DOUTx+/DOUTx− pin if the applied common-mode transient edge is coincident with a data
transition on the corresponding DINx+/DINx− pin. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges.
Rev. E | Page 3 of 25
ADN4650/ADN4651/ADN4652
Data Sheet
RECEIVER INPUT THRESHOLD TEST VOLTAGES
Table 2. Test Voltages for Receiver Operation
Applied Voltages
DINx+ (V)
DINx− (V)
1.25
1.15
1.15
1.25
2.4
2.3
2.3
2.4
0.1
0
0
0.1
1.5
0.9
0.9
1.5
2.4
1.8
1.8
2.4
0.6
0
0
0.6
Input Voltage, Differential (VID) (V)
0.1
−0.1
0.1
−0.1
0.1
−0.1
0.6
−0.6
0.6
−0.6
0.6
−0.6
Input Voltage, Common-Mode (VIC) (V)
1.2
+1.2
2.35
+2.35
0.05
+0.05
1.2
+1.2
2.1
+2.1
0.3
+0.3
Driver Output (VOD) (mV)
>250
250
250
250
250
250
1.3V
DINx+
1.2V
(DINx– = 1.2V)
400
II
μm min
V
Unit
V rms
mm min
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Material Group
Test Conditions/Comments
1-minute duration
Measured from input terminals to output terminals,
shortest distance through air
Measured from input terminals to output terminals,
shortest distance path along body
Measured from input terminals to output terminals,
shortest distance through air, line of sight, in the PCB
mounting plane
Insulation distance through insulation
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
Table 5. 20-Lead SSOP Package
Parameter
Rated Dielectric Insulation Voltage
Minimum External Air Gap (Clearance)
Symbol
L (I01)
Value
3750
5.3
Minimum External Tracking (Creepage)
L (I02)
5.3
mm min
Minimum Clearance in the Plane of the Printed
Circuit Board (PCB Clearance)
L (PCB)
5.6
mm min
CTI
22
>400
II
μm min
V
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Material Group
Rev. E | Page 5 of 25
Test Conditions/Comments
1-minute duration
Measured from input terminals to output terminals,
shortest distance through air
Measured from input terminals to output terminals,
shortest distance path along body
Measured from input terminals to output terminals,
shortest distance through air, line of sight, in the PCB
mounting plane
Insulation distance through insulation
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
ADN4650/ADN4651/ADN4652
Data Sheet
PACKAGE CHARACTERISTICS
Table 6.
Parameter
Resistance (Input to Output) 1
Capacitance (Input to Output)1
Input Capacitance 2
IC Junction to Ambient Thermal Resistance
20-Lead SOIC
20-Lead SSOP
1
2
Symbol
RI-O
CI-O
CI
θJA
Min
Typ
1013
2.2
3.7
Max
Unit
Ω
pF
pF
Test Conditions/Comments
f = 1 MHz
Thermal simulation with 4-layer standard JEDEC PCB
45.7
69.6
°C/W
°C/W
The device is considered a 2-terminal device: Pin 1 through Pin 10 are shorted together, and Pin 11 through Pin 20 are shorted together.
Input capacitance is from any input data pin to ground.
REGULATORY INFORMATION
See Table 12 and the Insulation Lifetime section for details regarding recommended maximum working voltages for specific crossisolation waveforms and insulation levels.
Table 7.
UL
To Be Recognized Under UL 1577
Component Recognition
Program 1
Single Protection, Isolation Voltage
20-lead SOIC, 5000 V rms
20-lead SSOP, 3750 V rms
File E214100
CSA
To be approved under CSA
Component Acceptance Notice 5A
VDE
To be certified according to DIN V VDE V 0884-10
(VDE V 0884-10):2006-12 2
Reinforced insulation, VIORM = 424 V peak, VIOSM = 6000 V peak
Basic insulation, VIORM = 424 V peak, VIOSM = 10,000 V peak
File 2471900-4880-0001
File 205078
In accordance with UL 1577, each ADN4650/ADN4651/ADN4652 is proof tested by applying an insulation test voltage ≥6000 V rms (20-lead SOIC) or ≥4500 V rms (20-lead SSOP)
for 1 sec.
2
In accordance with DIN V VDE V 0884-10, each ADN4650/ADN4651/ADN4652 is proof tested by applying an insulation test voltage ≥795 V peak for 1 sec (partial discharge
detection limit = 5 pC).
1
DIN V VDE V 0884-10 (VDE V 0884-10) INSULATION CHARACTERISTICS
This isolator is suitable for reinforced electrical isolation only within the safety limit data. Protective circuits ensure the maintenance of
the safety data.
Table 8.
Description
Installation Classification per DIN VDE 0110
For Rated Mains Voltage ≤ 150 V rms
For Rated Mains Voltage ≤ 300 V rms
For Rated Mains Voltage ≤ 600 V rms
Climatic Classification
Pollution Degree per DIN VDE 0110, Table 1
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method B1
Input to Output Test Voltage, Method A
After Environmental Tests Subgroup 1
After Input and/or Safety Test Subgroup 2
and Subgroup 3
Highest Allowable Overvoltage
Surge Isolation Voltage
Basic
Reinforced
Test Conditions/Comments
VIORM × 1.875 = Vpd (m), 100% production test,
tini = tm = 1 sec, partial discharge < 5 pC
Symbol
Characteristic
Unit
VIORM
Vpd (m)
I to IV
I to IV
I to III
40/125/21
2
424
795
V peak
V peak
636
V peak
509
V peak
VIOTM
5000
V peak
VIOSM
VIOSM
10,000
6000
V peak
V peak
Vpd (m)
VIORM × 1.5 = Vpd (m), tini = 60 sec, tm = 10 sec,
partial discharge < 5 pC
VIORM × 1.2 = Vpd (m), tini = 60 sec, tm = 10 sec,
partial discharge < 5 pC
VPEAK = 12.8 kV, 1.2 µs rise time, 50 µs, 50% fall time
VPEAK = 10 kV, 1.2 µs rise time, 50 µs, 50% fall time
Rev. E | Page 6 of 25
Data Sheet
ADN4650/ADN4651/ADN4652
Description
Test Conditions/Comments
(see Figure 5)
Maximum Junction Temperature
Total Power Dissipation at 25°C
20-Lead SOIC
20-Lead SSOP
Insulation Resistance at TS
VIO = 500 V
Unit
TS
PS
150
°C
2.78
1.8
>109
W
W
Ω
RECOMMENDED OPERATING CONDITIONS
20-LEAD SOIC
Table 9.
2.5
SAFE LIMITING POWER (W)
Characteristic
RS
3.0
2.0
Parameter
Operating Temperature
Supply Voltages
Supply to LDO
LDO Bypass, VINx Shorted to VDDx
20-LEAD SSOP
1.5
1.0
0
50
100
150
AMBIENT TEMPERATURE (°C)
200
13677-002
0.5
0
Symbol
Figure 5. Thermal Derating Curve, Dependence of Safety Limiting Values
with Ambient Temperature per DIN V VDE V 0884-10
Rev. E | Page 7 of 25
Symbol
TA
Rating
−40°C to +125°C
VIN1, VIN2
VDD1, VDD2
3.0 V to 3.6 V
2.375 V to 2.625 V
ADN4650/ADN4651/ADN4652
Data Sheet
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 10.
Parameter
VIN1 to GND1/VIN2 to GND2
VDD1 to GND1/VDD2 to GND2
Input Voltage (DINx+, DINx−) to GNDx on
the Same Side
Output Voltage (DOUTx+, DOUTx−) to
GNDx on the Same Side
Short-Circuit Duration (DOUTx+, DOUTx−)
to GNDx on the Same Side
Operating Temperature Range
Storage Temperature Range
Junction Temperature (TJ Maximum)
Power Dissipation
ESD
Human Body Model (All Pins to
Respective GNDx, 1.5 kΩ, 100 pF)
IEC 61000-4-2 (LVDS Pins to Isolated
GNDx Across Isolation Barrier)
20-Lead SOIC
20-Lead SSOP
θJA is specified for the worst case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Rating
−0.3 V to +6.5 V
−0.3 V to +2.8 V
−0.3 V to VDD + 0.3 V
Table 11. Thermal Resistance
Package Type
20-Lead SOIC
20-lead SSOP
−0.3 V to VDD + 0.3 V
θJA
45.7
69.6
Unit
°C/W
°C/W
Continuous
−40°C to +125°C
−65°C to +150°C
150°C
(TJ maximum − TA)/θJA
ESD CAUTION
±4 kV
±8 kV
±7 kV
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Table 12. Maximum Continuous Working Voltage1
Parameter
AC Voltage
Bipolar Waveform
Basic Insulation
Reinforced Insulation
Unipolar Waveform
Basic Insulation
Reinforced Insulation
DC Voltage
Basic Insulation
Reinforced Insulation
1
Rating
20-Lead SOIC
20-Lead SSOP
Constraint
495 V peak
495 V peak
424 V peak
424 V peak
50-year minimum insulation lifetime for 1% failure
50-year minimum insulation lifetime for 1% failure
990 V peak
875 V peak
848 V peak
620 V peak
50-year minimum insulation lifetime for 1% failure
Lifetime limited by package creepage, maximum approved working voltage
1079 V peak
536 V peak
754 V peak
380 V peak
Lifetime limited by package creepage, maximum approved working voltage
Lifetime limited by package creepage, maximum approved working voltage
The maximum continuous working voltage refers to the continuous voltage magnitude imposed across the isolation barrier. See the Insulation Lifetime section for
more details.
Rev. E | Page 8 of 25
Data Sheet
ADN4650/ADN4651/ADN4652
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
VIN1 1
20
VIN2
GND1 2
19
GND2
VDD1 3
18
VDD2
GND1 4
17
GND2
DIN1– 6
DIN2+ 7
ADN4650
DOUT1+
TOP VIEW
(Not to Scale) 15 DOUT1–
14 DOUT2+
16
DIN2– 8
13
DOUT2–
VDD1 9
12
VDD2
GND1 10
11
GND2
13677-104
DIN1+ 5
Figure 6. ADN4650 Pin Configuration
Table 13. ADN4650 Pin Function Descriptions
Pin No.
1
Mnemonic
VIN1
2, 4, 10
3, 9
GND1
VDD1
5
6
7
8
11, 17, 19
12, 18
DIN1+
DIN1−
DIN2+
DIN2−
GND2
VDD2
13
14
15
16
20
DOUT2−
DOUT2+
DOUT1−
DOUT1+
VIN2
Description
Optional 3.3 V Power Supply/LDO Input for Side 1. Bypass VIN1 to GND1 using a 1 μF capacitor. Alternatively, if using a
2.5 V supply, connect VIN1 directly to VDD1.
Ground, Side 1.
2.5 V Power Supply for Side 1. Connect both pins externally and bypass to GND1 with 0.1 μF capacitors. If supplying
3.3 V to VIN1, connect a 1 μF capacitor between Pin 3 and GND1 for proper regulation of the 2.5 V output of the
internal LDO.
Noninverted Differential Input 1.
Inverted Differential Input 1.
Noninverted Differential Input 2.
Inverted Differential Input 2.
Ground, Side 2.
2.5 V Power Supply for Side 2. Connect both pins externally and bypass to GND2 with 0.1 μF capacitors. If supplying
3.3 V to VIN2, connect a 1 μF capacitor between Pin 18 and GND2 for proper regulation of the 2.5 V output of the
internal LDO.
Inverted Differential Output 2.
Noninverted Differential Output 2.
Inverted Differential Output 1.
Noninverted Differential Output 1.
Optional 3.3 V Power Supply/LDO Input for Side 2. Bypass VIN2 to GND2 using a 1 μF capacitor. Alternatively, if using a
2.5 V supply, connect VIN2 directly to VDD2.
Rev. E | Page 9 of 25
ADN4650/ADN4651/ADN4652
Data Sheet
VIN1 1
20
VIN2
GND1 2
19
GND2
VDD1 3
18
VDD2
GND1 4
17
GND2
DIN1– 6
DOUT2+ 7
ADN4651
DOUT1+
TOP VIEW
(Not to Scale) 15 DOUT1–
14 DIN2+
16
DOUT2– 8
13
DIN2–
VDD1 9
12
VDD2
GND1 10
11
GND2
13677-003
DIN1+ 5
Figure 7. ADN4651 Pin Configuration
Table 14. ADN4651 Pin Function Descriptions
Pin No.
1
Mnemonic
VIN1
2, 4, 10
3, 9
GND1
VDD1
5
6
7
8
11, 17, 19
12, 18
DIN1+
DIN1−
DOUT2+
DOUT2−
GND2
VDD2
13
14
15
16
20
DIN2−
DIN2+
DOUT1−
DOUT1+
VIN2
Description
Optional 3.3 V Power Supply/LDO Input for Side 1. Bypass VIN1 to GND1 using a 1 μF capacitor. Alternatively, if using a
2.5 V supply, connect VIN1 directly to VDD1.
Ground, Side 1.
2.5 V Power Supply for Side 1. Connect both pins externally and bypass to GND1 with 0.1 μF capacitors. If supplying
3.3 V to VIN1, connect a 1 μF capacitor between Pin 3 and GND1 for proper regulation of the 2.5 V output of the
internal LDO.
Noninverted Differential Input 1.
Inverted Differential Input 1.
Noninverted Differential Output 2.
Inverted Differential Output 2.
Ground, Side 2.
2.5 V Power Supply for Side 2. Connect both pins externally and bypass to GND2 with 0.1 μF capacitors. If supplying
3.3 V to VIN2, connect a 1 μF capacitor between Pin 18 and GND2 for proper regulation of the 2.5 V output of the
internal LDO.
Inverted Differential Input 2.
Noninverted Differential Input 2.
Inverted Differential Output 1.
Noninverted Differential Output 1.
Optional 3.3 V Power Supply/LDO Input for Side 2. Bypass VIN2 to GND2 using a 1 μF capacitor. Alternatively, if using a
2.5 V supply, connect VIN2 directly to VDD2.
Rev. E | Page 10 of 25
ADN4650/ADN4651/ADN4652
VIN1 1
20
VIN2
GND1 2
19
GND2
VDD1 3
18
VDD2
GND1 4
17
GND2
16
DIN1+
15
DIN1–
DIN2+ 7
14
DOUT2+
DIN2– 8
13
DOUT2–
VDD1 9
12
VDD2
GND1 10
11
GND2
DOUT1+ 5
DOUT1– 6
ADN4652
TOP VIEW
(Not to Scale)
13677-108
Data Sheet
Figure 8. ADN4652 Pin Configuration
Table 15. ADN4652 Pin Function Descriptions
Pin No.
1
Mnemonic
VIN1
2, 4, 10
3, 9
GND1
VDD1
5
6
7
8
11, 17, 19
12, 18
DOUT1+
DOUT1−
DIN2+
DIN2−
GND2
VDD2
13
14
15
16
20
DOUT2−
DOUT2+
DIN1−
DIN1+
VIN2
Description
Optional 3.3 V Power Supply/LDO Input for Side 1. Bypass VIN1 to GND1 using a 1 μF capacitor. Alternatively, if using a
2.5 V supply, connect VIN1 directly to VDD1.
Ground, Side 1.
2.5 V Power Supply for Side 1. Connect both pins externally and bypass to GND1 with 0.1 μF capacitors. If supplying
3.3 V to VIN1, connect a 1 μF capacitor between Pin 3 and GND1 for proper regulation of the 2.5 V output of the
internal LDO.
Noninverted Differential Output 1.
Inverted Differential Output 1.
Noninverted Differential Input 2.
Inverted Differential Input 2.
Ground, Side 2.
2.5 V Power Supply for Side 2. Connect both pins externally and bypass to GND2 with 0.1 μF capacitors. If supplying
3.3 V to VIN2, connect a 1 μF capacitor between Pin 18 and GND2 for proper regulation of the 2.5 V output of the
internal LDO.
Inverted Differential Output 2.
Noninverted Differential Output 2.
Inverted Differential Input 1.
Noninverted Differential Input 1.
Optional 3.3 V Power Supply/LDO Input for Side 2. Bypass VIN2 to GND2 using a 1 μF capacitor. Alternatively, if using a
2.5 V supply, connect VIN2 directly to VDD2.
Rev. E | Page 11 of 25
ADN4650/ADN4651/ADN4652
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
70
60
60
30
20
IDD1
IDD2
IIN1
IIN2
10
0
0
50
100
150
200
250
300
INPUT CLOCK FREQUENCY (MHz)
20
0
–50
60
60
SUPPLY CURRENT (mA)
70
50
40
30
20
0
IDD1
IDD2
IIN1
IIN2
0
50
100
150
200
250
300
INPUT CLOCK FREQUENCY (MHz)
0
2.35
30
20
75
AMBIENT TEMPERATURE (°C)
100
125
2.40
2.45
2.50
(DIN2 ACTIVE)
(DIN2 ACTIVE)
(DIN1 ACTIVE)
(DIN1 ACTIVE)
2.55
2.60
2.65
50
40
30
20
IIN1 (DIN2 ACTIVE)
IIN2 (DIN2 ACTIVE)
IIN1 (DIN1 ACTIVE)
IIN2 (DIN1 ACTIVE)
10
13677-006
50
IDD1
IDD2
IDD1
IDD2
Figure 13. IDD1/IDD2 Supply Current vs. Supply Voltage, VDD1/VDD2
IDD1
IDD2
IIN1
IIN2
25
125
SUPPLY VOLTAGE, VDD1 /VDD2 (V)
SUPPLY CURRENT (mA)
40
100
20
60
50
75
30
60
0
50
40
70
–25
25
50
70
0
–50
0
10
Figure 10. IDD1/IDD2 or IIN1/IIN2 Supply Current vs. DIN2± Input Clock Frequency
(DIN1± Not Switching)
10
–25
Figure 12. IDD1/IDD2 or IIN1/IIN2 Supply Current vs. Ambient Temperature (TA)
(DIN2± with 300 MHz Clock Input, DIN1± Not Switching)
70
10
IDD1
IDD2
IIN1
IIN2
AMBIENT TEMPERATURE (°C)
13677-005
SUPPLY CURRENT (mA)
30
10
Figure 9. IDD1/IDD2 or IIN1/IIN2 Supply Current vs. DIN1± Input Clock Frequency
(DIN2± Not Switching)
SUPPLY CURRENT (mA)
40
13677-008
40
50
Figure 11. IDD1/IDD2 or IIN1/IIN2 Supply Current vs. Ambient Temperature (TA)
(DIN1± with 300 MHz Clock Input, DIN2± Not Switching)
Rev. E | Page 12 of 25
0
3.00
3.15
3.30
3.45
3.60
SUPPLY VOLTAGE, VIN1/VIN2 (V)
Figure 14. IIN1/IIN2 Supply Current vs. Supply Voltage, VIN1/VIN2
13677-009
50
13677-007
SUPPLY CURRENT (mA)
70
13677-004
SUPPLY CURRENT (mA)
VDD1 = VDD2 = 2.5 V, TA = 25°C, RL = 100 Ω, 300 MHz input with |VID| = 200 mV, and VIC = 1.1 V, unless otherwise noted.
Data Sheet
ADN4650/ADN4651/ADN4652
2.60
2.55
2.50
2.45
2.40
2.35
3.0
VDD1
VDD2
3.1
3.2
3.3
3.4
3.5
3.6
LDO INPUT VOLTAGE, VIN1/VIN2 (V)
1.40
1.35
1.30
VOH CHANNEL 1
VOH CHANNEL 2
2.40
2.45
2.50
2.55
2.60
2.65
Figure 18. Driver Output High Voltage, VOH vs. Supply Voltage, VDD1/VDD2
1.25
330
320
310
300
290
280
270
VOD CHANNEL 1
VOD CHANNEL 2
260
50
100
150
200
250
300
350
Figure 16. Driver Differential Output Voltage, VOD vs. Input Clock Frequency
1.10
1.05
1.00
0.95
0.90
2.35
VOL CHANNEL 1
VOL CHANNEL 2
2.40
2.45
2.50
2.55
2.60
2.65
SUPPLY VOLTAGE, VDD1 /VDD2 (V)
Figure 19. Driver Output Low Voltage, VOL vs. Supply Voltage, VDD1/VDD2
1.375
DRIVER OUTPUT OFFSET VOLTAGE, VOS (V)
450
400
350
300
250
200
150
100
50
VOD CHANNEL 1
VOD CHANNEL 2
75
100
OUTPUT LOAD, RL (Ω)
125
150
Figure 17. Driver Differential Output Voltage, VOD vs. Output Load, RL
1.325
1.275
1.225
1.175
1.125
2.35
13677-012
0
50
1.15
VOS CHANNEL 1
VOS CHANNEL 2
2.40
2.45
2.50
2.55
SUPPLY VOLTAGE, VDD1 /VDD2 (V)
2.60
2.65
13677-015
0
1.20
13677-014
DRIVER OUTPUT LOW VOLTAGE, VOL (V)
340
INPUT CLOCK FREQUENCY (MHz)
DRIVER DIFFERENTIAL OUTPUT VOLTAGE, VOD (mV)
1.45
SUPPLY VOLTAGE, VDD1 /VDD2 (V)
350
250
1.50
1.25
2.35
13677-011
DRIVER DIFFERENTIAL OUTPUT VOLTAGE, VOD (mV)
Figure 15. LDO Output Voltage, VDD1/VDD2 vs. LDO Input Voltage, VIN1/VIN2
1.55
13677-013
DRIVER OUTPUT HIGH VOLTAGE, VOH (V)
1.60
13677-010
LDO OUTPUT VOLTAGE, VDD1 /VDD2 (V)
2.65
Figure 20. Driver Output Offset Voltage, VOS vs. Supply Voltage, VDD1/VDD2
Rev. E | Page 13 of 25
ADN4650/ADN4651/ADN4652
3.60
3.40
3.35
3.30
2.35
2.40
2.45
2.50
2.55
2.60
2.65
SUPPLY VOLTAGE, VDD1 AND VDD2 (V)
Figure 21. Differential Propagation Delay vs. Supply Voltage, VDD1 and VDD2
3.8
3.7
3.6
3.5
3.4
3.3
tPHL CHANNEL 2
tPLH CHANNEL 2
tPHL CHANNEL 1
tPLH CHANNEL 1
3.2
3.1
3.0
–50
–25
0
25
50
75
100
125
AMBIENT TEMPERATURE (°C)
Figure 22. Differential Propagation Delay vs. Ambient Temperature (TA)
3.50
3.45
3.40
tPHL CHANNEL 2
tPLH CHANNEL 2
tPHL CHANNEL 1
tPLH CHANNEL 1
3.35
3.30
0
0.2
0.4
0.6
0.8
1.0
DIFFERENTIAL INPUT VOLTAGE, VID (V)
1.2
1.4
Figure 23. Differential Propagation Delay vs. Receiver Differential Input
Voltage, VID
0
0.5
1.0
1.5
2.0
2.5
240
tF CHANNEL 2
tR CHANNEL 2
tF CHANNEL 1
tR CHANNEL 1
220
200
180
160
140
120
2.35
2.40
2.45
2.50
2.55
2.60
2.65
SUPPLY VOLTAGE, VDD1 /VDD2 (V)
Figure 25. Differential Output Transition Time vs. Supply Voltage, VDD1/VDD2
DIFFERENTIAL OUTPUT TRANSITION TIME (ps)
3.55
3.35
Figure 24. Differential Propagation Delay vs. Receiver Input Offset Voltage, VIC
13677-019
DIFFERENTIAL PROPAGATION DELAY (ns)
3.60
3.40
RECEIVER INPUT OFFSET VOLTAGE, VIC (V)
DIFFERENTIAL OUTPUT TRANSITION TIME (ps)
3.9
3.45
3.30
13677-018
DIFFERENTIAL PROPAGATION DELAY (ns)
4.0
3.50
13677-020
3.45
3.55
13677-021
3.50
tPHL CHANNEL 2
tPLH CHANNEL 2
tPHL CHANNEL 1
tPLH CHANNEL 1
240
220
200
180
160
tF CHANNEL 2
tR CHANNEL 2
tF CHANNEL 1
tR CHANNEL 1
140
120
–50
–25
0
25
50
75
AMBIENT TEMPERATURE (°C)
100
125
13677-022
3.55
DIFFERENTIAL PROPAGATION DELAY (ns)
tPHL CHANNEL 2
tPLH CHANNEL 2
tPHL CHANNEL 1
tPLH CHANNEL 1
13677-017
DIFFERENTIAL PROPAGATION DELAY (ns)
3.60
Data Sheet
Figure 26. Differential Output Transition Time vs. Ambient Temperature (TA)
Rev. E | Page 14 of 25
Data Sheet
ADN4650/ADN4651/ADN4652
30
50
15
10
5
0
2.35
tSK(D) CHANNEL 2
tSK(D) CHANNEL 1
2.40
2.45
2.50
2.55
2.60
2.65
SUPPLY VOLTAGE, VDD1 AND VDD2 (V)
40
35
30
25
20
15
10
CHANNEL 1
CHANNEL 2
5
0
2.35
2.40
2.45
2.50
2.55
2.60
2.65
SUPPLY VOLTAGE, VDD1 /VDD2 (V)
Figure 27. Duty Cycle Skew, tSK(D) vs. Supply Voltage, VDD1 and VDD2
13677-026
DETERMINISTIC JITTER, tDJ(PP) (ps)
20
13677-023
DUTY CYCLE SKEW, tSK(D) (ps)
45
25
Figure 30. Deterministic Jitter, tDJ(PP) vs. Supply Voltage, VDD1/VDD2
30
50
15
10
5
0
–50
tSK(D) CHANNEL 2
tSK(D) CHANNEL 1
–25
0
25
50
75
100
125
AMBIENT TEMPERATURE (°C)
40
35
30
25
20
15
10
CHANNEL 1
CHANNEL 2
5
Figure 28. Duty Cycle Skew, tSK(D) vs. Ambient Temperature (TA)
0
2.35
2.40
2.45
2.50
2.55
2.60
2.65
SUPPLY VOLTAGE, VDD1 /VDD2 (V)
Figure 31. Deterministic Jitter, tDJ(PP) vs. Ambient Temperature
35
30
25
20
15
10
5
0
100
200
300
400
500
DATA RATE (Mbps)
600
CH1 50mV
CH3 10mV
CH2 50mV
CH4 10mV
300ps/DIV
DELAY 61.0828ns
Figure 32. ADN4651 Eye Diagram for DOUT1±
Figure 29. Deterministic Jitter, tDJ(PP) vs. Data Rate
Rev. E | Page 15 of 25
13677-028
0
CHANNEL 1
CHANNEL 2
13677-025
DETERMINISTIC JITTER, tDJ(PP) (ps)
40
13677-026
DETERMINISTIC JITTER, tDJ(PP) (ps)
20
13677-024
DUTY CYCLE SKEW, tSK(D) (ps)
45
25
CH1 50mV
CH3 10mV
CH2 50mV
CH4 10mV
300ps/DIV
DELAY 61.0828ns
Data Sheet
13677-029
ADN4650/ADN4651/ADN4652
Figure 33. ADN4651 Eye Diagram for DOUT2±
Rev. E | Page 16 of 25
Data Sheet
ADN4650/ADN4651/ADN4652
TEST CIRCUITS AND SWITCHING CHARACTERISTICS
DINx+
VIN–
V
RL/2
DOUTx–
VOS
V
VOD
R
DINx–
D
DOUTx–
NOTES
1. VTEST = 0V TO 2.4V
3.75kΩ
Figure 36. Voltage Definitions
DINx+
VTEST
SIGNAL
GENERATOR
V
RL
3.75kΩ
V VOD
50Ω
13677-031
DOUTx+
VOUT+
VOUT–
NOTES
1. VID = VIN+ – VIN–
2. VIC = (VIN+ + VIN–)/2
3. VOD = VOUT+ – VOUT–
4. VOS = (VOUT+ + VOUT–)/2
Figure 34. Driver Test Circuit
DINx+
VOD
DOUTx–
13677-032
DINx–
RL/2
D
13677-030
R
D
DINx–
DOUTx+
R
50Ω DINx–
Rev. E | Page 17 of 25
RL
D
DOUTx–
NOTES
1. CL INCLUDES PROBE AND JIG CAPACITANCE.
Figure 35. Driver Test Circuit (Full Load Across Common-Mode Range)
CL
Figure 37. Timing Test Circuit
CL
13677-033
DOUTx+
R
VID
VIN+
DINx+
DOUTx+
ADN4650/ADN4651/ADN4652
Data Sheet
THEORY OF OPERATION
The ADN4650/ADN4651/ADN4652 are TIA/EIA-644-A LVDS
compliant isolated buffers. LVDS signals applied to the inputs are
transmitted on the outputs of the buffer, and galvanic isolation
is integrated between the two sides of the device. This integration
allows drop-in isolation of LVDS signal chains.
The LVDS receiver detects the differential voltage present across a
termination resistor on an LVDS input. An integrated digital
isolator transmits the input state across the isolation barrier,
and an LVDS driver outputs the same state as the input.
With a positive differential voltage of ≥100 mV across any DINx±
pin, the corresponding DOUTx+ pin sources current. This current
flows across the connected transmission line and termination at
the receiver at the far end of the bus, while DOUTx− sinks the return
current. With a negative differential voltage of ≤−100 mV across
any DINx± pin, the corresponding DOUTx+ pin sinks current, with
DOUTx− sourcing the current. Table 16 and Table 17 show these
input/output combinations.
The output drive current is between ±2.5 mA and ±4.5 mA
(typically ±3.1 mA), developing between ±250 mV and ±450 mV
across a 100 Ω termination resistor (RT). The received voltage is
centered around 1.2 V. Note that because the differential voltage
(VID) reverses polarity, the peak-to-peak voltage swing across RT
is twice the differential voltage magnitude (|VID|).
TRUTH TABLE AND FAIL-SAFE RECEIVER
The LVDS standard, TIA/EIA-644-A, defines normal receiver
operation under two conditions: an input differential voltage
of ≥+100 mV corresponding to one logic state, and a voltage of
≤−100 mV for the other logic state. Between these thresholds,
standard LVDS receiver operation is undefined (it may detect
either state), as shown in Table 16 for the ADN4650. The
ADN4651/ADN4652 incorporate a fail-safe circuit to ensure
the LVDS outputs are in a known state (logic high) when the
input state is undefined (−100 mV < VID < +100 mV), as shown
in Table 17.
This input state can occur when the inputs are floating
(unconnected, no termination resistor), when the inputs are
shorted, and when there is no active driver connected to the inputs
(but with a termination resistor). Open-circuit, short-circuit, and
terminated/idle bus fail-safes, respectively, ensure a known output
state for these conditions, as implemented by the
ADN4651/ADN4652.
After the fail-safe circuit is triggered by these input states
(−100 mV < VID < +100 mV), there is a delay of up to 1.2 µs
before the output is guaranteed to be high (VOD ≥ 250 mV).
During this time, the output may transition to or stay in a logic
low state (VOD ≤ −250 mV).
The fail-safe circuit triggers as soon as the input differential
voltage remains between +100 mV and −100 mV for some
nanoseconds. This means that very slow rise and fall times on
the input signal, outside typical LVDS operation (350 ps maximum
tR/tF), can potentially trigger the fail-safe circuit on a high to low
crossover.
At the minimum |VID| of 100 mV for normal operation, the
rise/fall time must be ≤5 ns to avoid triggering a fail-safe state.
Increasing |VID| to 200 mV correspondingly allows an input
rise/fall time of up to 10 ns without triggering a fail-safe state.
For very low speed applications where slow high to low transitions
in excess of this limit are expected, using external biasing resistors
is an option to introduce a minimum |VID| of 100 mV (that is,
the fail-safe cannot trigger).
Table 16. ADN4650 Input/Output Operation
Powered On
Yes
Yes
Yes
No
Input (DINx±)
VID (mV)
≥100
≤−100
−100 < VID < +100
Don’t care
Logic
High
Low
Indeterminate
Don’t care
Powered On
Yes
Yes
Yes
Yes
Output (DOUTx±)
VOD (mV)
≥250
≤−250
Indeterminate
≥250
Logic
High
Low
Indeterminate
High
Table 17. ADN4651/ADN4652 Input/Output Operation
Powered On
Yes
Yes
Yes
No
Input (DINx±)
VID (mV)
≥100
≤−100
−100 < VID < +100
Don’t care
Logic
High
Low
Indeterminate
Don’t care
Rev. E | Page 18 of 25
Powered On
Yes
Yes
Yes
Yes
Output (DOUTx±)
VOD (mV)
≥250
≤−250
≥250
≥250
Logic
High
Low
High
High
Data Sheet
ADN4650/ADN4651/ADN4652
In the absence of input transitions for more than approximately
1 µs, a periodic set of refresh pulses, indicative of the correct input
state, ensures dc correctness at the output (including the fail-safe
output state, if applicable). These periodic refresh pulses also
correct the output state within 1 μs in the event of a fault condition
or set the ADN4651/ADN4652 output to the fail-safe state.
The ADN4650/ADN4651/ADN4652 require appropriate
decoupling of the VDDx pins with 100 nF capacitors. If the
integrated LDO is not used, and a 2.5 V supply is connected
directly, connect the appropriate VINx pin to the supply as well,
as shown in Figure 38, using the ADN4651 as an example.
100nF
VIN1
On power-up, the output state may initially be in the incorrect
dc state if there are no input transitions. The output state is
corrected within 1 µs by the refresh pulses.
If the decoder receives no internal pulses for more than
approximately 1 µs, the device assumes that the input side is
unpowered or nonfunctional, in which case, the output is set to
a positive differential voltage (logic high).
GND1
VDD1
100Ω
20
2
19
Controlled 50 Ω impedance traces are needed on the LVDS
signal lines for full signal integrity, reduced system jitter, and
minimizing electromagnetic interference (EMI) from the PCB.
Trace widths, lateral distance within each pair, and distance to the
ground plane underneath all must be chosen appropriately. Via
fencing to the PCB ground between pairs is also a best practice to
minimize crosstalk between adjacent pairs.
The ADN4650/ADN4651/ADN4652 pass EN55022 Class B
emissions limits without extra considerations required for the
isolator when operating with up to 600 Mbps PRBS data. When
isolating high speed clocks (for example, 300 MHz), a reduced
PCB clearance (isolation gap) may be required with the 20-lead
SOIC models to reduce dipole antenna effects and provide
sufficient margin below Class B emissions limits. The 20-lead
SSOP models pass the Class B limits up to 150 MHz clock
frequencies with no extra PCB measures.
VDD2
3
18
4
17
GND2
DIN1+
5
16
6
TOP VIEW
(Not to Scale) 15
DOUT1+
DIN1–
DOUT2+
7
14
DIN2+
DOUT2–
8
13
DIN2–
9
12
GND1
10
11
ADN4651
100nF
The ADN4650/ADN4651/ADN4652 can operate with high
speed LVDS signals up to 300 MHz clock, or 600 Mbps nonreturn
to zero (NRZ) data. With such high frequencies, it is particularly
important to apply best practices for the LVDS trace layout and
termination. Locate a 100 Ω termination resistor as close as
possible to the receiver, across the DINx+ and DINx− pins.
VIN2
GND2
GND1
VDD1
PCB LAYOUT
100nF
1
DOUT1–
100Ω
VDD2
GND2
100nF
13677-035
In response to any change in the input state detected by the
integrated LVDS receiver, an encoder circuit sends narrow (~1 ns)
pulses to a decoder circuit using integrated transformer coils.
The decoder is bistable and is, therefore, either set or reset by
the pulses that indicate input transitions. The decoder state
determines the LVDS driver output state in normal operation,
and this in turn reflects the isolated LVDS buffer input state.
The best practice for high speed PCB design avoids any other emissions from PCBs in applications that use the ADN4650/ADN4651/
ADN4652. Special care is recommended for off board connections,
where switching transients from high speed LVDS signals (and
clocks in particular) may conduct onto cabling, resulting in
radiated emissions. Use common-mode chokes, ferrites, or
other filters as appropriate at the LVDS connectors, as well as
cable shield or PCB ground connections to earth/chassis.
Figure 38. Required PCB Layout When Not Using the LDO (2.5 V Supply)
1µF 100nF
1µF
VIN1
1
100nF 1µF
1µF
20
VIN2
GND1
2
19
3
18
GND1
4
17
GND2
DIN1+
5
16
6
TOP VIEW
(Not to Scale) 15
DOUT1+
DIN1–
DOUT2+
7
14
DIN2+
DOUT2–
8
13
DIN2–
9
12
GND1
10
11
VDD1
100Ω
VDD1
ADN4651
100nF
GND2
VDD2
DOUT1–
100Ω
VDD2
GND2
100nF
13677-036
ISOLATION
Figure 39. Required PCB Layout When Using the LDO (3.3 V Supply)
When the integrated LDO is used, bypass capacitors of 1 µF are
required on the VINx pins and on the nearest VDDx pins (LDO
output), as shown in Figure 39, using the ADN4651 as an
example.
MAGNETIC FIELD IMMUNITY
The limitation on the magnetic field immunity of the device
is set by the condition in which the induced voltage in the
transformer receiving coil is sufficiently large, either to falsely
set or reset the decoder. The following analysis defines such
conditions. The ADN4650/ADN4651/ADN4652 are examined
in a 2.375 V operating condition because it represents the most
susceptible mode of operation for this product.
Rev. E | Page 19 of 25
ADN4650/ADN4651/ADN4652
Data Sheet
where:
β is the magnetic flux density.
rn is the radius of the nth turn in the receiving coil.
N is the number of turns in the receiving coil.
Given the geometry of the receiving coil in the ADN4650/
ADN4651/ADN4652, and an imposed requirement that the
induced voltage be, at most, 50% of the 0.25 V margin at the
decoder, a maximum allowable magnetic field is calculated
as shown in Figure 40.
MAXIMUM ALLOWABLE MAGNETIC FLUX
DENSITY (kgauss)
100
DISTANCE = 100mm
10
DISTANCE = 5mm
1
0.1
0.01
1k
100k
10k
10M
1M
MAGNETIC FIELD FREQUENCY (Hz)
100M
Figure 41. Maximum Allowable Current for Various Current to
ADN4650/ADN4651/ADN4652 Spacings
Note that at combinations of strong magnetic field and high
frequency, any loops formed by PCB traces can induce
sufficiently large error voltages to trigger the thresholds of
succeeding circuitry. Avoid PCB structures that form loops.
1k
100
10
INSULATION LIFETIME
All insulation structures eventually break down when subjected
to voltage stress over a sufficiently long period. The rate of
insulation degradation is dependent on the characteristics of
the voltage waveform applied across the insulation as well as on
the materials and material interfaces.
1
0.1
10k
100k
1M
10M
MAGNETIC FIELD FREQUENCY (Hz)
100M
13677-037
0.01
0.001
1k
DISTANCE = 1m
1k
13677-038
V = (−dβ/dt)∑πrn2; n = 1, 2, …, N
10k
MAXIMUM ALLOWABLE CURRENT (kA)
The pulses at the transformer output have an amplitude greater
than 0.5 V. The decoder has a sensing threshold of about 0.25 V,
therefore establishing a 0.25 V margin in which induced voltages
are tolerated. The voltage induced across the receiving coil is
given by the following:
Figure 40. Maximum Allowable External Magnetic Flux Density
For example, at a magnetic field frequency of 1 MHz, the
maximum allowable magnetic field of 0.92 kgauss induces a
voltage of 0.125 V at the receiving coil. This voltage is about
50% of the sensing threshold and does not cause a faulty output
transition. If such an event occurs with the worst case polarity
during a transmitted pulse, it reduces the received pulse from
>0.5 V to 0.375 V. This voltage is still higher than the 0.25 V
sensing threshold of the decoder.
The preceding magnetic flux density values correspond to specific
current magnitudes at given distances from the ADN4650/
ADN4651/ADN4652 transformers. Figure 41 expresses these
allowable current magnitudes as a function of frequency for
selected distances. The ADN4650/ADN4651/ADN4652 are
very insensitive to external fields. Only extremely large, high
frequency currents, very close to the component, can potentially
be a concern. For the 1 MHz example noted, a 2.29 kA current
must be placed 5 mm from the ADN4650/ADN4651/ADN4652
to affect component operation.
The two types of insulation degradation of primary interest are
breakdown along surfaces exposed to the air and insulation wear
out. Surface breakdown is the phenomenon of surface tracking
and the primary determinant of surface creepage requirements
in system level standards. Insulation wear out is the phenomenon
where charge injection or displacement currents inside the
insulation material cause long-term insulation degradation.
Surface Tracking
Surface tracking is addressed in electrical safety standards by
setting a minimum surface creepage based on the working voltage,
the environmental conditions, and the properties of the insulation
material. Safety agencies perform characterization testing on the
surface insulation of components that allows the components to be
categorized in different material groups. Lower material group
ratings are more resistant to surface tracking and, therefore, can
provide adequate lifetime with smaller creepage. The minimum
creepage for a given working voltage and material group is in
each system level standard and is based on the total rms voltage
across the isolation barrier, pollution degree, and material group.
The material group and creepage for ADN4650/ADN4651/
ADN4652 are presented in Table 4 and Table 5.
Rev. E | Page 20 of 25
Data Sheet
ADN4650/ADN4651/ADN4652
Insulation Wear Out
The working voltage across the barrier from Equation 1 is
The lifetime of insulation caused by wear out is determined by
the thickness, material properties, and the voltage stress applied.
It is important to verify that the product lifetime is adequate at
the application working voltage. The working voltage supported by
an isolator for wear out may not be the same as the working
voltage supported for tracking. It is the working voltage applicable
to tracking that is specified in most standards.
Testing and modeling show that the primary driver of long-term
degradation is displacement current in the polyimide insulation
causing incremental damage. The stress on the insulation can be
broken down into broad categories, such as dc stress, which causes
very little wear out because there is no displacement current,
and an ac component time varying voltage stress, which causes
wear out.
The ratings in certification documents are usually based on
60 Hz sinusoidal stress because this reflects isolation from line
voltage. However, many practical applications have combinations
of 60 Hz ac and dc across the isolation barrier, as shown in
Equation 1. Because only the ac portion of the stress causes
wear out, the equation can be rearranged to solve for the ac rms
voltage, as shown in Equation 2. For insulation wear out with the
polyimide materials used in this product, the ac rms voltage
determines the product lifetime.
VRMS = VAC RMS2 + VDC 2
(1)
VAC RMS = VRMS 2 − VDC 2
(2)
VRMS = VAC RMS2 + VDC 2
VRMS = 2402 + 4002
VRMS = 466 V
This VRMS value is the working voltage used together with the
material group and pollution degree when looking up the creepage
required by a system standard.
To determine if the lifetime is adequate, obtain the time varying
portion of the working voltage. To obtain the ac rms voltage,
use Equation 2.
VAC RMS = VRMS 2 − VDC 2
VAC RMS = 4662 − 4002
VAC RMS = 240 V rms
In this case, the ac rms voltage is simply the line voltage of
240 V rms. This calculation is more relevant when the waveform is
not sinusoidal. The value is compared to the limits for the working
voltage in Table 12 for the expected lifetime, less than a 60 Hz
sine wave, and it is well within the limit for a 50-year service life.
Note that the dc working voltage limit in Table 12 is set by the
creepage of the package as specified in IEC 60664-1. This value
can differ for specific system level standards.
where:
VRMS is the total rms working voltage.
VAC RMS is the time varying portion of the working voltage.
VDC is the dc offset of the working voltage.
ISOLATION VOLTAGE
or
VAC RMS
VPEAK
VRMS
VDC
The following example frequently arises in power conversion
applications. Assume that the line voltage on one side of the
isolation is 240 V ac rms and a 400 V dc bus voltage is present
on the other side of the isolation barrier. The isolator material is
polyimide. To establish the critical voltages in determining the
creepage, clearance, and lifetime of a device, see Figure 42 and
the following equations.
Rev. E | Page 21 of 25
TIME
Figure 42. Critical Voltage Example
13677-039
Calculation and Use of Parameters Example
ADN4650/ADN4651/ADN4652
Data Sheet
APPLICATIONS INFORMATION
High speed LVDS interfaces can be isolated using the ADN4650/
ADN4651/ADN4652 either between components, between boards,
or at a cable interface. The ADN4650/ADN4651/ADN4652 offer
full LVDS compliant inputs and outputs, allowing increased LVDS
output drive strength compared to built-in reduced specification
LVDS interfaces on other components. The LVDS compliant
receiver inputs on the ADN4650/ADN4651/ADN4652 also ensure
full compatibility with any LVDS source being isolated.
Newer programmable logic controller (PLC) and input/output
modules communicate across an LVDS backplane, illustrating a
board to board LVDS interface, as shown in Figure 45. With a
daisy-chain type topology for transmit and receive to either
adjacent node, two ADN4651 (or ADN4652) devices on each
node can isolate four LVDS channels. The addition of galvanic
isolation allows a much more robust backplane interface port
on the PLC or input/output modules.
Isolated analog front-end applications provide an example of
the ADN4650/ADN4651 isolating an LVDS interface between
components. As shown in Figure 43, two ADN4650 components
isolate the LVDS interface of the AD7960 analog-to-digital
converter (ADC), including 600 Mbps data, a 300 MHz echoed
clock, and a 5 MHz sample clock. Isolation of the AD7960 using
two ADN4651 components is shown in Figure 44. The ADN4651
additive phase jitter is sufficiently low that it does not affect the
ADC performance even when isolating the sample clock. In
addition, implementing the galvanic isolation improves ADC
performance by removing digital and power supply noise from
the field-programmable gate array (FPGA) circuit.
With galvanic isolation, even LVDS ports can be treated as full
external ports and transmitted along cable runs (see Figure 46),
even in harsh environments where high common-mode
voltages may be induced on the cable. The low jitter of the
ADN4651/ADN4652 ensures that more of the jitter budget can
be used to account for the cable effects, allowing the cable to be
as long as possible. The ADN4651/ADN4652 offer a high drive
strength, fully LVDS compliant output, capable of driving short
cable runs of a few meters. This is in contrast to alternative
isolation methods that degrade the LVDS signal quality. The
data rate can be chosen as appropriate for the cable length; the
ADN4651/ADN4652 operate not only at 600 Mbps but also at
any arbitrary data rate down to dc.
D±
100Ω
DCO±
100Ω
ISOLATION
ADN4650
100Ω D±
100Ω DCO±
AD7960
100Ω
CNV±
100Ω
100Ω
CLK±
100Ω
CNV±
13677-040
CLK±
ISOLATION
FPGA/ASIC
ADN4650
Figure 43. Example Isolated Analog Front-End Implementation (Isolated AD7960 Using the ADN4650)
100Ω
D±
CLK±
100Ω
ISOLATION
ADN4651
100Ω D±
100Ω
CLK±
AD7960
CNV±
100Ω
100Ω DCO±
100Ω
CNV±
ADN4651
Figure 44. Example Isolated Analog Front-End Implementation (Isolated AD7960 Using the ADN4651)
Rev. E | Page 22 of 25
13677-040
100Ω
DCO±
ISOLATION
FPGA/ASIC
Data Sheet
ADN4650/ADN4651/ADN4652
ISOLATION
100Ω
CONNECTOR
100Ω
MODULE 1
100Ω
ISOLATION
100Ω
100Ω
100Ω
100Ω
ISOLATION
100Ω
MODULE 2
100Ω
100Ω
ISOLATION
100Ω
ISOLATION
100Ω
100Ω
CONNECTOR
100Ω
13677-041
100Ω
MCU 3
CONNECTOR
ISOLATION
100Ω
ADN4651
100Ω
MODULE 3
Figure 45. Example Isolated Backplane Implementation for PLCs and Input/Output Modules Using the ADN4651
SHIELDED
TWISTED PAIR
CABLE
Figure 46. Example Isolated LVDS Cable Application Using the ADN4651
Rev. E | Page 23 of 25
100Ω
FPGA/
ASIC
100Ω
13677-042
ISOLATION
100Ω
ADN4651
CONNECTOR
100Ω
CONNECTOR
100Ω
FPGA/
ASIC
100Ω
ADN4651
ISOLATION
CONNECTOR
ADN4651
100Ω
MCU 2
ADN4651
MCU 1
ADN4650/ADN4651/ADN4652
Data Sheet
OUTLINE DIMENSIONS
13.00 (0.5118)
12.60 (0.4961)
11
20
7.60 (0.2992)
7.40 (0.2913)
1
10.65 (0.4193)
10.00 (0.3937)
10
2.65 (0.1043)
2.35 (0.0925)
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
1.27
(0.0500)
BSC
SEATING
PLANE
0.75 (0.0295)
45°
0.25 (0.0098)
8°
0°
1.27 (0.0500)
0.40 (0.0157)
0.33 (0.0130)
0.20 (0.0079)
06-07-2006-A
COMPLIANT TO JEDEC STANDARDS MS-013-AC
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 47. 20-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-20)
Dimensions shown in millimeters and (inches)
7.50
7.20
6.90
11
20
5.60
5.30
5.00
1
8.20
7.80
7.40
10
PIN 1
INDICATOR
TOP VIEW
0.65 BSC
PKG-004600
0.05 MIN
COPLANARITY
0.10
0.25
0.09
1.85
1.75
1.65
SIDE VIEW
0.38
0.22
SEATING
PLANE
END VIEW
8°
4°
0°
COMPLIANT TO JEDEC STANDARDS MO-150-AE
0.95
0.75
0.55
06-01-2006-A
2.00 MAX
Figure 48. 20-Lead Shrink Small Outline Package [SSOP]
(RS-20)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
ADN4650BRWZ
ADN4650BRWZ-RL7
ADN4650BRSZ
ADN4650BRSZ-RL7
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
20-Lead, Wide Body, Standard Small Outline Package [SOIC_W]
20-Lead, Wide Body, Standard Small Outline Package [SOIC_W]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
Rev. E | Page 24 of 25
Package Option
RW-20
RW-20
RS-20
RS-20
Data Sheet
Model 1
ADN4651BRSZ
ADN4651BRSZ-RL7
ADN4651BRWZ
ADN4651BRWZ-RL7
ADN4652BRSZ
ADN4652BRSZ-RL7
ADN4652BRWZ
ADN4652BRWZ-RL7
EVAL-ADN4650EBZ
EVAL-ADN4650EB1Z
EVAL-ADN4651EBZ
EVAL-ADN4651EB1Z
EVAL-ADN4652EBZ
EVAL-ADN4652EB1Z
1
ADN4650/ADN4651/ADN4652
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead, Wide Body, Standard Small Outline Package [SOIC_W]
20-Lead, Wide Body, Standard Small Outline Package [SOIC_W]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead, Wide Body, Standard Small Outline Package [SOIC_W]
20-Lead, Wide Body, Standard Small Outline Package [SOIC_W]
ADN4650 SSOP Evaluation Board
ADN4650 SOIC_W Evaluation Board
ADN4651 SSOP Evaluation Board
ADN4651 SOIC_W Evaluation Board
ADN4652 SSOP Evaluation Board
ADN4652 SOIC_W Evaluation Board
Z = RoHS Compliant Part.
©2015–2019 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D13677-0-6/19(E)
Rev. E | Page 25 of 25
Package Option
RS-20
RS-20
RW-20
RW-20
RS-20
RS-20
RW-20
RW-20