Dual, 3 V, CMOS, LVDS
High Speed Differential Driver
ADN4663
±15 kV ESD protection on output pins
600 Mbps (300 MHz) switching rates
Flow-through pinout simplifies PCB layout
300 ps typical differential skew
700 ps maximum differential skew
1.5 ns maximum propagation delay
3.3 V power supply
±355 mV differential signaling
Low power dissipation: 23 mW typical
Interoperable with existing 5 V LVDS receivers
Conforms to TIA/EIA-644 LVDS standard
Industrial operating temperature range (−40°C to +85°C)
Available in surface-mount (SOIC) package
FUNCTIONAL BLOCK DIAGRAM
VCC
ADN4663
DOUT1+
DIN1
DOUT1–
DOUT2+
DIN2
DOUT2–
GND
07927-001
FEATURES
Figure 1.
APPLICATIONS
Backplane data transmission
Cable data transmission
Clock distribution
GENERAL DESCRIPTION
The ADN4663 is a dual, CMOS, low voltage differential
signaling (LVDS) line driver offering data rates of over
600 Mbps (300 MHz), and ultralow power consumption.
It features a flow-through pinout for easy PCB layout and
separation of input and output signals.
The device accepts low voltage TTL/CMOS logic signals and
converts them to a differential current output of typically
±3.1 mA for driving a transmission medium such as a
twisted-pair cable. The transmitted signal develops a differential
voltage of typically ±355 mV across a termination resistor at the
receiving end, and this is converted back to a TTL/CMOS logic
level by a line receiver.
The ADN4663 and a companion receiver offer a new solution
to high speed point-to-point data transmission, and a low
power alternative to emitter-coupled logic (ECL) or positive
emitter-coupled logic (PECL).
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
ADN4663
TABLE OF CONTENTS
Features .............................................................................................. 1
ESD Caution...................................................................................6
Applications ....................................................................................... 1
Pin Configuration and Function Descriptions..............................7
Functional Block Diagram .............................................................. 1
Typical Performance Characteristics ..............................................8
General Description ......................................................................... 1
Theory of Operation ...................................................................... 11
Revision History ............................................................................... 2
Applications Information .......................................................... 11
Specifications..................................................................................... 3
Outline Dimensions ....................................................................... 12
AC Characteristics........................................................................ 4
Ordering Guide .......................................................................... 12
Absolute Maximum Ratings............................................................ 6
REVISION HISTORY
1/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
ADN4663
SPECIFICATIONS
VCC = 3.0 V to 3.6 V; RL = 100 Ω; CL = 15 pF to GND; all specifications TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter 1, 2
LVDS OUTPUTS (DOUTx+, DOUTx−)
Differential Output Voltage
Change in Magnitude of VOD for
Complementary Output States
Offset Voltage
Change in Magnitude of VOS for
Complementary Output States
Output High Voltage
Output Low Voltage
INPUTS (DIN1, DIN2)
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
Input Clamp Voltage
LVDS OUTPUT PROTECTION (DOUTx+, DOUTx−)
Output Short-Circuit Current 3
LVDS OUTPUT LEAKAGE (DOUTx+, DOUTx−)
Power-Off Leakage
POWER SUPPLY
Supply Current, Unloaded
Supply Current, Loaded
ESD PROTECTION
DOUTx+, DOUTx− Pins
All Pins Except DOUTx+, DOUTx−
Symbol
Min
Typ
Max
Unit
Test Conditions
VOD
ΔVOD
250
355
1
450
35
mV
|mV|
See Figure 2 and Figure 4
See Figure 2 and Figure 4
VOS
ΔVOS
1.125
1.2
3
1.375
25
V
|mV|
See Figure 2 and Figure 4
See Figure 2 and Figure 4
1.4
1.1
1.6
V
V
See Figure 2 and Figure 4
See Figure 2 and Figure 4
VCC
0.8
+10
+10
V
V
μA
μA
V
VIN = 3.3 V or 2.4 V
VIN = GND or 0.5 V
ICL = −18 mA
−5.7
−8.0
mA
DINx = VCC, DOUTx+ = 0 V or DINx = GND, DOUTx− = 0 V
±1
+10
μA
VOUT = VCC or GND, VCC = 0 V
8
10
14
20
mA
mA
No load, DINx = VCC or GND
DINx = VCC or GND
kV
kV
Human body model
Human body model
VOH
VOL
0.90
VIH
VIL
IIH
IIL
VCL
2.0
GND
−10
−10
−1.5
IOS
IOFF
ICC
ICCL
−10
±2
±1
−0.6
±15
±4
1
Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD, ΔVOD, and ΔVOS.
The ADN4663 is a current mode device and functions within data sheet specifications only when a resistive load is applied to the driver outputs. Typical range is
90 Ω to 110 Ω.
3
Output short-circuit current (IOS) is specified as magnitude only; minus sign indicates direction only.
2
Rev. 0 | Page 3 of 12
ADN4663
AC CHARACTERISTICS
VCC = 3.0 V to 3.6 V; RL = 100 Ω; CL 1 = 15 pF to GND; all specifications TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter 2
Differential Propagation Delay High to Low
Differential Propagation Delay Low to High
Differential Pulse Skew |tPHLD − tPLHD| 5
Channel-to-Channel Skew 6
Differential Part-to-Part Skew 7
Differential Part-to-Part Skew 8
Rise Time
Fall Time
Maximum Operating Frequency 9
Symbol
tPHLD
tPLHD
tSKD1
tSKD2
tSKD3
tSKD4
tTLH
tTHL
fMAX
Min
0.3
0.3
0
0
0
0
0.2
0.2
Typ
0.8
1.1
0.3
0.4
0.5
0.5
350
1
Max
1.5
1.5
0.7
0.8
1.0
1.2
1.0
1.0
Unit
ns
ns
ns
ns
ns
ns
ns
ns
MHz
Conditions/Comments 3, 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3
CL includes probe and jig capacitance.
AC parameters are guaranteed by design and characterization.
Generator waveform for all tests, unless otherwise specified: f = 50 MHz, ZO = 50 Ω, tTLH ≤ 1 ns, and tTHL ≤ 1 ns.
4
All input voltages are for one channel, unless otherwise specified. Other inputs are set to GND.
5
tSKD1 = |tPHLD − tPLHD| is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the
same channel.
6
tSKD2 is the differential channel-to-channel skew of any event on the same device.
7
tSKD3, differential part-to-part skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This specification
applies to devices at the same VCC and within 5°C of each other within the operating temperature range.
8
tSKD4, differential part-to-part skew, is the differential channel-to-channel skew of any event between devices. This specification applies to devices over recommended
operating temperatures and voltage ranges, and across process distribution. tSKD4 is defined as |maximum − minimum| differential propagation delay.
9
fMAX generator input conditions: tTLH = tTHL < 1 ns (0% to 100%), 50% duty cycle, 0 V to 3 V. Output criteria: duty cycle = 45% to 55%, VOD > 250 mV, all channels
switching.
2
3
Rev. 0 | Page 4 of 12
ADN4663
Test Circuits and Timing Diagrams
DOUTx+
VCC
VCC
RL/2
RL/2
V
VOS
V
VOD
07927-002
DINx
DOUTx–
Figure 2. Test Circuit for Driver VOD and VOS
DOUTx+
VCC
CL
SIGNAL
GENERATOR
DINx
RL
DOUTx–
50Ω
07927-003
CL
CL INCLUDES LOAD AND TEST JIG CAPACITANCE.
Figure 3. Test Circuit for Driver Propagation Delay, Transition Time, and Maximum Operating Frequency
3V
DINx
1.5V
1.5V
0V
tPHLD
tPLHD
VOH
DOUTx–
0V (DIFFERENTIAL) VOD
0V
DOUTx+
VOL
80%
0V
0V
VDIFF = DOUT+ – DOUT–
20%
20%
tTHL
tTHL
Figure 4. Driver Propagation Delay and Transition Time Waveforms
Rev. 0 | Page 5 of 12
07927-004
VDIFF
80%
ADN4663
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted. All voltages are relative to
their respective ground.
Table 3.
Parameter
VCC to GND
Input Voltage (DINx) to GND
Output Voltage (DOUTx+, DOUTx−) to GND
Short-Circuit Duration (DOUTx+, DOUTx−) to GND
Operating Temperature Range
Industrial
Storage Temperature Range
Junction Temperature (TJ max)
Power Dissipation
SOIC Package
θJA Thermal Impedance
Reflow Soldering Peak Temperature
Pb-Free
Rating
−0.3 V to +4 V
−0.3 V to VCC + 0.3 V
−0.3 V to VCC + 0.3 V
Continuous
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
−40°C to +85°C
−65°C to +150°C
150°C
(TJ max − TA)/θJA
149.5°C/W
260°C ± 5°C
Rev. 0 | Page 6 of 12
ADN4663
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
ADN4663
7
3
TOP VIEW
(Not to Scale)
DOUT1+
DIN2
6
DOUT2+
GND
4
5
DOUT2–
8
07927-005
DOUT1–
VCC
DIN1
Figure 5. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
Mnemonic
VCC
2
3
4
5
DIN1
DIN2
GND
DOUT2−
6
DOUT2+
7
DOUT1+
8
DOUT1−
Description
Power Supply Input. The part can be operated from 3.0 V to 3.6 V, and the supply should be decoupled with a
10 μF solid tantalum capacitor in parallel with a 0.1 μF capacitor to GND.
Driver Channel 1 Logic Input.
Driver Channel 2 Logic Input.
Ground reference point for all circuitry on the part.
Channel 2 Inverting Output Current Driver. When DIN2 is high, current flows into DOUT2−. When DIN2 is low, current
flows out of DOUT2−.
Channel 2 Noninverting Output Current Driver. When DIN2 is high, current flows out of DOUT2+. When DIN2 is low,
current flows into DOUT2+.
Channel 1 Noninverting Output Current Driver. When DIN1 is high, current flows out of DOUT1+. When DIN1 is low,
current flows into DOUT1+.
Channel 1 Inverting Output Current Driver. When DIN1 is high, current flows into DOUT1−. When DIN1 is low, current
flows out of DOUT1−.
Rev. 0 | Page 7 of 12
ADN4663
TYPICAL PERFORMANCE CHARACTERISTICS
325.0
1.414
1.413
3.2
3.3
3.4
3.5
3.6
POWER SUPPLY VOLTAGE, VCC (V)
DIFFERENTIAL OUTPUT VOLTAGE, VOD (mV)
3.3
3.4
3.5
3.6
POWER SUPPLY VOLTAGE, VCC (V)
OFFSET VOLTAGE, VOS (mV)
–4.1
3.5
3.6
POWER SUPPLY VOLTAGE, VCC (V)
07927-008
SHORT-CIRCUIT CURRENT, I OS (mA)
–4.0
3.4
3.6
400
350
300
90
1.252
3.3
3.5
TA = 25°C
VCC = 3.3V
TA = 25°C
VIN = GND OR VCC
VOUT = 0V
3.2
3.4
100
110
120
130
140
150
3.6
Figure 10. Differential Output Voltage vs. Load Resistor
–3.9
3.1
3.3
LOAD RESISTOR, RL (Ω)
Figure 7. Output Low Voltage vs. Power Supply Voltage
–4.2
3.0
3.2
450
250
07927-007
OUTPUT LOW VOLTAGE, VOL (V)
1.088
3.2
3.1
POWER SUPPLY VOLTAGE, VCC (V)
500
1.089
3.1
324.2
Figure 9. Differential Output Voltage vs. Power Supply Voltage
TA = 25°C
RL = 100Ω
1.087
3.0
324.4
324.0
3.0
Figure 6. Output High Voltage vs. Power Supply Voltage
1.090
324.6
07927-010
3.1
324.8
07927-011
1.412
3.0
TA = 25°C
RL = 100Ω
07927-009
DIFFERENTIAL OUTPUT VOLTAGE, VOD (mV)
TA = 25°C
RL = 100Ω
07927-006
OUTPUT HIGH VOLTAGE, VOH (V)
1.415
Figure 8. Output Short-Circuit Current vs. Power Supply Voltage
TA = 25°C
RL = 100Ω
1.251
1.250
1.249
3.0
3.1
3.2
3.3
3.4
3.5
POWER SUPPLY VOLTAGE, VCC (V)
Figure 11. Offset Voltage vs. Power Supply Voltage
Rev. 0 | Page 8 of 12
ADN4663
13
ONE CHANNEL SWITCHING
9
7
5
0.01
0.1
1
10
100
1k
SWITCHING FREQUENCY (MHz)
1200
DIFFERENTIAL PROPAGATION DELAY (ns)
11.5
11.0
10.5
3.1
3.2
3.3
3.4
3.5
3.6
POWER SUPPLY VOLTAGE, VCC (V)
DIFFERENTIAL SKEW, tSKD1 (ps)
12
11
10
35
60
TEMPERATURE (°C)
3.5
3.6
tPLHD
1100
tPHLD
1000
100
VCC = 3.3V
f = 1MHz
CL = 15pF
VIN = 0V TO 3V
RL = 100Ω PER DRIVER
–15
3.4
–20
0
20
40
60
80
100
Figure 16. Differential Propagation Delay vs. Ambient Temperature
13
10
–40
3.3
AMBIENT TEMPERATURE, TA (°C)
85
07927-014
POWER SUPPLY CURRENT, ICC (mA)
14
3.2
VCC = 3.3V
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
900
–40
Figure 13. Power Supply Current vs. Power Supply Voltage
15
3.1
Figure 15. Differential Propagation Delay vs. Power Supply Voltage
TA = 25°C
f = 1MHz
CL = 15pF
VIN = 0V TO 3.3V
RL = 100Ω PER DRIVER
10.0
3.0
1000
POWER SUPPLY VOLTAGE, VCC (V)
07927-013
POWER SUPPLY CURRENT, ICC (mA)
12.0
tPLHD
900
3.0
Figure 12. Power Supply Current vs. Switching Frequency
12.5
tPHLD
07927-016
11
1100
07927-015
BOTH CHANNELS SWITCHING
TA = 25°C
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
Figure 14. Power Supply Current vs. Ambient Temperature
80
TA = 25°C
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
60
40
20
0
3.0
3.1
3.2
3.3
3.4
3.5
POWER SUPPLY VOLTAGE, VCC (V)
Figure 17. Differential Skew vs. Power Supply Voltage
Rev. 0 | Page 9 of 12
3.6
07927-017
15
DIFFERENTIAL PROPAGATION DELAY (ns)
17
1200
TA = 25°C
CL = 15pF
VCC = 3.3V
VIN = 0V TO 3.3V
RL = 100Ω PER DRIVER
07927-012
POWER SUPPLY CURRENT, ICC (mA)
19
ADN4663
TRANSITION TIME (ps)
30
20
380
tTLH
360
tTHL
340
10
0
–40
–20
0
20
40
60
80
100
AMBIENT TEMPERATURE, TA (°C)
Figure 18. Differential Skew vs. Ambient Temperature
400
TA = 25°C
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
380
tTLH
360
tTHL
340
320
3.0
3.1
3.2
3.3
3.4
3.5
POWER SUPPLY VOLTAGE, VCC (V)
320
–40
–20
0
20
40
60
80
AMBIENT TEMPERATURE, TA (°C)
Figure 20. Transition Time vs. Ambient Temperature
3.6
07927-019
TRANSITION TIME (ps)
VCC = 3.3V
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
Figure 19. Transition Time vs. Power Supply Voltage
Rev. 0 | Page 10 of 12
100
07927-020
40
400
VCC = 3.3V
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
07927-018
DIFFERENTIAL SKEW, tSKD1 (ps)
50
ADN4663
THEORY OF OPERATION
When DINx is high (Logic 1), current flows out of the DOUTx+ pin
(current source) through RT and back into the DOUTx− pin (current
sink). At the receiver, this current develops a positive differential
voltage across RT (with respect to the inverting input) and results
in a Logic 1 at the receiver output. When DINx is low, DOUTx+
sinks current and DOUTx− sources current; a negative differential
voltage across RT results in a Logic 0 at the receiver output.
The output drive current is between ±2.5 mA and ±4.5 mA
(typically ±3.55 mA), developing between ±250 mV and ±450 mV
across a 100 Ω termination resistor. The received voltage is centered
around the receiver offset of 1.2 V. Therefore, the noninverting
receiver input is typically (1.2 V + [355 mV/2]) = 1.377 V, and
the inverting receiver input is (1.2 V − [355 mV/2]) = 1.023 V
for Logic 1. For Logic 0, the inverting and noninverting output
voltages are reversed. Note that because the differential voltage
reverses polarity, the peak-to-peak voltage swing across RT is
twice the differential voltage.
A current mode device simply reverses a constant current
between its two outputs, with no significant overlap currents.
This is similar to emitter-coupled logic (ECL) and positive
emitter-coupled logic (PECL), but without the high quiescent
current of ECL and PECL.
APPLICATIONS INFORMATION
Figure 21 shows a typical application for point-to-point data
transmission using the ADN4663 as the driver and a LVDS
receiver.
+3.3V
+ 10µF
TANTALUM
0.1µF
+
VCC
VCC
ADN4663
Rev. 0 | Page 11 of 12
DOUTx+
RT
100Ω
DINx
Current mode drivers offer considerable advantages over
voltage mode drivers such as RS-422 drivers. The operating
current remains fairly constant with increased switching
frequency, whereas that of voltage mode drivers increase
exponentially in most cases. This is caused by the overlap
as internal gates switch between high and low, which causes
currents to flow from the device power supply to ground.
+3.3V
DOUTx–
GND
DIN+
LVDS RECEIVER
DOUT
DIN–
GND
Figure 21. Typical Application Circuit
07927-021
The ADN4663 is a dual line driver for low voltage differential
signaling. It takes a single-ended 3 V logic signal and converts
it to a differential current output. The data can then be transmitted
for considerable distances, over media such as a twisted-pair cable
or PCB backplane, to an LVDS receiver, where it develops a voltage
across a terminating resistor, RT. This resistor is chosen to match
the characteristic impedance of the medium, typically around
100 Ω. The differential voltage is detected by the receiver and
converted back into a single-ended logic signal.
ADN4663
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
1
5
6.20 (0.2441)
5.80 (0.2284)
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
0.50 (0.0196)
0.25 (0.0099)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-A A
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
Figure 22. 8-Lead Standard Small Outline Package [SOIC(N)]
(R-8)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model
ADN4663BRZ 1
ADN4663BRZ-REEL71
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
8-Lead Standard Small Outline Package [SOIC-N]
8-Lead Standard Small Outline Package [SOIC-N]
Z = RoHS Compliant Part.
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07927-0-1/09(0)
Rev. 0 | Page 12 of 12
Package Option
R-8
R-8
工商网监
湘ICP备2023018690号
