FEATURES
±15 kV ESD protection on output pins
400 Mbps (200 MHz) switching rates
Flow through pinout simplifies PCB layout
300 ps typical differential skew
400 ps maximum differential skew
1.7 ns maximum propagation delay
3.3 V power supply
±310 mV differential signaling
Low power dissipation (10 mW typical)
Interoperable with existing 5 V LVDS receivers
High impedance on LVDS outputs on power-down
Conforms to TIA/EIA-644 LVDS standards
Industrial operating temperature range: −40°C to +85°C
Available in surface-mount (SOIC) and low profile
TSSOP package
Qualified for automotive applications
FUNCTIONAL BLOCK DIAGRAM
VCC
ADN4667
DOUT1+
DIN1
D1
DIN2
D2
DIN3
D3
DIN4
D4
DOUT1–
DOUT2+
DOUT2–
DOUT3+
DOUT3–
DOUT4+
DOUT4–
EN
EN
GND
07032-001
Data Sheet
3 V LVDS Quad CMOS
Differential Line Driver
ADN4667
Figure 1.
APPLICATIONS
Backplane data transmission
Cable data transmission
Clock distribution
GENERAL DESCRIPTION
The ADN4667 is a quad, CMOS, low voltage differential signaling
(LVDS) line driver offering data rates of over 400 Mbps (200 MHz)
and ultralow power consumption. It features a flow through
pinout for easy PCB layout and separation of input and output
signals.
The device accepts low voltage TTL/CMOS logic signals and
converts them to a differential current output of typically ±3.1 mA
for driving a transmission medium such as a twisted pair cable.
The transmitted signal develops a differential voltage of typically ±310 mV across a termination resistor at the receiving end.
This is converted back to a TTL/CMOS logic level by an LVDS
receiver, such as the ADN4668.
The ADN4667 also offers active high and active low enable/
disable inputs (EN and EN). These inputs control all four drivers
and turn off the current outputs in the disabled state to reduce
the quiescent power consumption to typically 10 mW.
The ADN4667 and its companion LVDS receiver, the ADN4668,
offer a new solution to high speed, point-to-point data transmission, and a low power alternative to emitter-coupled logic
(ECL) or positive emitter-coupled logic (PECL).
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2008–2012 Analog Devices, Inc. All rights reserved.
ADN4667
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Pin Configuration and Function Descriptions..............................7
Applications ....................................................................................... 1
Typical Performance Characteristics ..............................................8
Functional Block Diagram .............................................................. 1
Theory of Operation ...................................................................... 11
General Description ......................................................................... 1
Enable Inputs .............................................................................. 11
Revision History ............................................................................... 2
Applications Information .......................................................... 11
Specifications..................................................................................... 3
Outline Dimensions ....................................................................... 12
AC Characteristics ........................................................................ 4
Ordering Guide .......................................................................... 13
Absolute Maximum Ratings ............................................................ 6
Automotive Products ................................................................. 13
ESD Caution .................................................................................. 6
REVISION HISTORY
3/12—Rev. A to Rev. B
Change to Features Section ............................................................. 1
Changes to Ordering Guide .......................................................... 13
Added Automotive Products Section........................................... 13
5/08—Rev. 0 to Rev. A
Added 16-Lead SOIC_N Package .................................... Universal
Changes to Table 3 ............................................................................ 6
Changes to Applications Information section ............................ 11
Updated Outline Dimensions ...................................................... 11
Changes to Ordering Guide .......................................................... 12
1/08—Revision 0: Initial Version
Rev. B | Page 2 of 16
Data Sheet
ADN4667
SPECIFICATIONS
VCC = 3.0 V to 3.6 V; RL = 100 Ω; CL = 15 pF to GND; all specifications TMIN to TMAX, unless otherwise noted. All typical values are given
for VCC = +3.3 V, TA = +25°C.
Table 1.
Parameter
LVDS OUTPUTS (DOUT+, DOUT−)
Differential Output Voltage
Change in Magnitude of VOD for Complementary Output States
Offset Voltage
Change in Magnitude of VOS for Complementary Output States
Output High Voltage
Output Low Voltage
INPUTS (DIN, EN, EN)
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
Input Clamp Voltage
LVDS OUTPUT PROTECTION (DOUT+, DOUT−)
Output Short-Circuit Current 3
Symbol
Min
Typ
Max
Unit
Conditions/Comments 1, 2
VOD
ΔVOD
VOS
ΔVOS
VOH
VOL
250
310
1
1.17
1
1.33
1.02
450
35
1.375
25
1.6
mV
|mV|
V
|mV|
V
V
See Figure 2 and Figure 4
See Figure 2 and Figure 4
See Figure 2 and Figure 4
See Figure 2 and Figure 4
See Figure 2 and Figure 4
See Figure 2 and Figure 4
VIH
VIL
IIH
IIL
VCL
2.0
GND
−10
−10
−1.5
VCC
0.8
+10
+10
V
V
μA
μA
V
VIN = VCC or 2.5 V
VIN = GND or 0.4 V
ICL = −18 mA
IOS
−4.2
−9.0
mA
Differential Output Short-Circuit Current3
LVDS OUTPUT LEAKAGE (DOUT+, DOUT−)
Power-Off Leakage
IOSD
−4.2
−9.0
mA
Output Three-State Current
1.125
0.90
+2
+2
−0.8
IOFF
−20
±1
+20
μA
IOZ
−10
±1
+10
μA
POWER SUPPLY
No Load Supply Current, Drivers Enabled
Loaded Supply Current, Drivers Enabled
ICC
ICCL
4.0
20
8.0
30
mA
mA
No Load Supply Current, Drivers Disabled
ICCZ
2.2
6.0
mA
ESD PROTECTION
DOUT+, DOUT−
All Pins Except DOUT+, DOUT−
±15
±4
1
kV
kV
Enabled, DIN = VCC, DOUT+ = 0 V
or
DIN = GND, DOUT− = 0 V
Enabled, VOD = 0 V
VOUT = 0 V or 3.6 V, VCC = 0 V or
open
EN = 0.8 V and EN = 2.0 V, VOUT
=0V
or VCC
DIN = VCC or GND
RL = 100 Ω all channels, DIN =
VCC
or GND (all inputs)
DIN = VCC or GND, EN = GND, EN
= VCC
Human body model
Human body model
Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD, ΔVOD, and ΔVOS.
The ADN4667 is a current mode device and functions within data sheet specifications only when a resistive load is applied to the driver outputs. Typical range is
90 Ω to 110 Ω.
3
Output short-circuit current (IOS) is specified as magnitude only; minus sign indicates direction only.
2
Rev. B | Page 3 of 16
ADN4667
Data Sheet
AC CHARACTERISTICS
VCC = 3.0 V to 3.6 V; RL = 100 Ω; CL 1 = 15 pF to GND; all specifications TMIN to TMAX, unless otherwise noted. All typical values are given
for VCC = +3.3 V, TA = +25°C.
Table 2.
Parameter 2
Differential Propagation Delay, High to Low, tPHLD
Differential Propagation Delay, Low to High, tPLHD
Differential Pulse Skew |tPHLD − tPLHD|, tSKD1 5
Channel-to-Channel Skew, tSKD2 6
Differential Part-to-Part Skew, tSKD3 7
Differential Part-to-Part Skew, tSKD4 8
Rise Time, tr
Fall Time, tf
Disable Time High to Inactive, tPHZ
Disable Time Low to Inactive, tPLZ
Enable Time Inactive to High, tPZH
Enable Time Inactive to Low, tPZL
Maximum Operating Frequency, fMAX 9
Min
0.5
0.5
0
0
0
0
200
Typ
0.9
1.2
0.3
0.4
Max
1.7
1.7
0.4
0.5
1.0
1.2
1.5
1.5
5
5
7
7
0.5
0.5
2
2
3
3
250
Conditions/Comments 3, 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 3 and Figure 4
See Figure 5 and Figure 6
See Figure 5 and Figure 6
See Figure 5 and Figure 6
See Figure 5 and Figure 6
See Figure 5 and Figure 6
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
MHz
1
CL includes probe and jig capacitance.
AC parameters are guaranteed by design and characterization.
3
Generator waveform for all tests unless otherwise specified: f = 50 MHz, ZO = 50 Ω, tr ≤ 1 ns, and tf ≤ 1 ns.
4
All input voltages are for one channel unless otherwise specified. Other inputs are set to GND.
5
tSKD1 = |tPHLD − tPLHD| is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the
same channel.
6
tSKD2 is the differential channel-to-channel skew of any event on the same device.
7
tSKD3, differential part-to-part skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This specification
applies to devices at the same VCC and within 5°C of each other within the operating temperature range.
8
tSKD4, part-to-part skew, is the differential channel-to-channel skew of any event between devices. This specification applies to devices over recommended operating
temperatures and voltage ranges, and across process distribution. tSKD4 is defined as |maximum − minimum| differential propagation delay.
9
fMAX generator input conditions: tr = tf < 1 ns (0% to 100%), 50% duty cycle, 0 V to 3 V. Output criteria: duty cycle = 45% to 55%, VOD > 250 mV, all channels switching.
2
Test Circuits and Timing Diagrams
DOUT+
VCC
RL/2
DIN
V VOS
V VOD
07032-002
RL/2
DOUT–
DRIVER IS ENABLED
Figure 2. Test Circuit for Driver VOD and VOS
VCC
DOUT+
CL
SIGNAL
GENERATOR
DIN
DOUT–
50Ω
DRIVER IS
ENABLED
NOTES
1. CL INCLUDES LOAD AND TEST JIG CAPACITANCE.
07032-003
CL
Figure 3. Test Circuit for Driver Propagation Delay and Transition Time
Rev. B | Page 4 of 16
Data Sheet
ADN4667
3V
DIN
1.5V
0V
tPLHD
tPHLD
VOD
DOUT–
VOH
0V (DIFFERENTIAL)
VOL
DOUT+
80%
0V
VDIFF = DOUT+ – DOUT–
tTLH
20%
07032-004
VDIFF
tTHL
Figure 4. Driver Propagation Delay and Transition Time Waveforms
DOUT+
CL
50Ω
VCC
1.2V
50Ω
DIN
DOUT–
CL
SIGNAL
GENERATOR
50Ω
07032-005
EN
EN
Figure 5. Test Circuit for Driver Three-State Delay
3V
EN WITH EN = GND
OR OPEN CIRCUIT
1.5V
0V
3V
EN WITH EN = VCC
1.5V
0V
tPHZ
tPZH
DOUT+ WITH DIN = VCC
OR DOUT– WITH DIN = GND
VOH
50%
1.2V
1.2V
50%
tPLZ
Figure 6. Driver Three-State Delay Waveforms
Rev. B | Page 5 of 16
tPZL
VOL
07032-006
DOUT+ WITH DIN = GND
OR DOUT– WITH DIN = VCC
ADN4667
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3.
Parameter
VCC to GND
Input Voltage (DIN) to GND
Enable Input Voltage (EN, EN) to GND
Output Voltage (DOUT+, DOUT−) to GND
Short-Circuit Duration (DOUT+, DOUT−) to GND
Industrial Operating Temperature Range
Storage Temperature Range
Junction Temperature (TJ max)
Power Dissipation
θJA Thermal Impedance
TSSOP Package
SOIC Package
Reflow Soldering Peak Temperature (10sec)
Rating
−0.3 V to +4 V
−0.3 V to VCC + 0.3 V
−0.3 V to VCC + 0.3 V
−0.3 V to VCC + 0.3 V
Continuous
−40°C to +85°C
−65°C to +150°C
150°C
(TJ max − TA)/θJA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
150.4°C/W
125°C/W
260°C max
Rev. B | Page 6 of 16
Data Sheet
ADN4667
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
16
15
DOUT1+
DIN2 3
ADN4667
14
DOUT2+
VCC 4
TOP VIEW
(Not to Scale)
13
DOUT2–
12
DOUT3–
DIN3 6
11
DOUT3+
DIN4 7
10
DOUT4+
EN 8
9
DOUT4–
GND 5
NC = NO CONNECT
07032-007
DOUT1–
EN 1
DIN1 2
Figure 7. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
Mnemonic
EN
2
3
4
DIN1
DIN2
VCC
5
6
7
8
GND
DIN3
DIN4
EN
9
DOUT4−
10
DOUT4+
11
DOUT3+
12
DOUT3−
13
DOUT2−
14
DOUT2+
15
DOUT1+
16
DOUT1−
Description
Active High Enable and Power-Down Input (3 V TTL/CMOS). If EN is held low or open circuit, EN enables the
drivers when high and disables the drivers when low.
Driver Channel 1 Logic Input.
Driver Channel 2 Logic Input.
Power Supply Input. These parts can be operated from 3.0 V to 3.6 V. The supply should be decoupled with a
10 μF solid tantalum capacitor in parallel with a 0.1 μF capacitor to GND.
Ground Reference Point for All Circuitry on the Part.
Driver Channel 3 Logic Input.
Driver Channel 4 Logic Input.
Active Low Enable and Power-Down Input with Pull-Down (3 V TTL/CMOS). If EN is held high, EN enables the
drivers when low or open circuit and disables the drivers and powers down the device when high.
Channel 4 Inverting Output Current Driver. When DIN4 is high, current flows into DOUT4−. When DIN4 is low, current
flows out of DOUT4−.
Channel 4 Noninverting Output Current Driver. When DIN4 is high, current flows out of DOUT4+. When DIN4 is low,
current flows into DOUT4+.
Channel 3 Noninverting Output Current Driver. When DIN3 is high, current flows out of DOUT3+. When DIN3 is low,
current flows into DOUT3+.
Channel 3 Inverting Output Current Driver. When DIN3 is high, current flows into DOUT3−.When DIN3 is low, current
flows out of DOUT3−.
Channel 2 Inverting Output Current Driver. When DIN2 is high, current flows into DOUT2−. When DIN2 is low, current
flows out of DOUT2−.
Channel 2 Noninverting Output Current Driver. When DIN2 is high, current flows out of DOUT2+. When DIN2 is low,
current flows into DOUT2+.
Channel 1 Noninverting Output Current Driver. When DIN1 is high, current flows out of DOUT1+. When DIN1 is low,
current flows into DOUT1+.
Channel 1 Inverting Output Current Driver. When DIN1 is high, current flows into DOUT1−. When DIN1 is low, current
flows out of DOUT1−.
Rev. B | Page 7 of 16
ADN4667
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
440
1.414
1.412
3.0
07032-008
1.413
3.1
3.2
3.3
3.4
3.5
TA = 25°C
VIN = GND OR VCC
420
400
380
360
07032-011
TA = 25°C
RL = 100Ω
OUTPUT THREE-STATE CURRENT, IOZ (pA)
OUTPUT HIGH VOLTAGE, VOH (V)
1.415
340
3.0
3.6
3.1
07032-009
1.088
3.2
3.3
3.4
3.5
DIFFERENTIAL OUTPUT VOLTAGE, VOD (mV)
OUTPUT LOW VOLTAGE, VOL (V)
325.0
1.089
3.1
324.6
324.4
324.2
3.1
3.4
3.5
3.6
3.5
450
400
350
300
250
90
3.6
POWER SUPPLY VOLTAGE, VCC (V)
TA = 25°C
VCC = 3.3V
07032-013
–4.1
DIFFERENTIAL OUTPUT VOLTAGE, VOD (mV)
–4.0
07032-010
SHORT-CIRCUIT CURRENT, IOS (mA)
500
3.4
3.3
Figure 12. Differential Output Voltage vs. Power Supply Voltage
TA = 25°C
VIN = GND OR VCC
VOUT = 0V
3.3
3.2
POWER SUPPLY VOLTAGE, VCC (V)
–3.9
3.2
3.6
324.8
324.0
3.0
3.6
Figure 9. Output Low Voltage vs. Power Supply Voltage
3.1
3.5
TA = 25°C
RL = 100Ω
POWER SUPPLY VOLTAGE, VCC (V)
–4.2
3.0
3.4
Figure 11. Output Three-State Current vs. Power Supply Voltage
TA = 25°C
RL = 100Ω
1.087
3.0
3.3
07032-012
Figure 8. Output High Voltage vs. Power Supply Voltage
1.090
3.2
POWER SUPPLY VOLTAGE, VCC (V)
POWER SUPPLY VOLTAGE, VCC (V)
100
110
120
130
140
LOAD RESISTOR, RL (Ω)
Figure 10. Output Short-Circuit Current vs. Power Supply Voltage
Figure 13. Differential Output Voltage vs. Load Resistor
Rev. B | Page 8 of 16
150
Data Sheet
14.92
1.251
1.249
3.0
07032-014
1.250
3.1
3.2
3.3
3.4
3.5
14.91
14.90
VCC = 3.3V
f = 1MHz
CL = 15pF
VIN = 0V TO 3V
RL = 100Ω PER DRIVER
14.89
14.88
–40
3.6
–20
POWER SUPPLY VOLTAGE, VCC (V)
ALL CHANNELS SWITCHING
20
18
16
ONE CHANNEL SWITCHING
10
100
1100
tPHLD
tPLHD
1000
900
3.0
500
3.1
3.3
3.4
3.5
3.4
3.5
3.6
3.6
VCC = 3.3V
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
tPLHD
1100
tPHLD
1000
900
–40
07032-019
DIFFERENTIAL PROPAGATION DELAY (ns)
14.915
07032-016
POWER SUPPLY CURRENT, ICC (mA)
1200
14.920
3.2
3.3
Figure 18. Differential Propagation Delay vs. Power Supply Voltage
TA = 25°C
f = 1MHz
CL = 15pF
VIN = 0V TO 3V
RL = 100Ω PER DRIVER
3.1
3.2
POWER SUPPLY VOLTAGE, VCC (V)
Figure 15.Power Supply Current vs. Switching Frequency
14.910
3.0
100
TA = 25°C
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
SWITCHING FREQUENCY (MHz)
14.925
80
07032-018
DIFFERENTIAL PROPAGATION DELAY (ns)
22
1
60
1200
TA = 25°C
CL = 15pF
VCC = 3.3V
VIN = 0V TO 3V
RL = 100Ω PER DRIVER
14
0.1
40
Figure 17. Power Supply Current vs. Ambient Temperature
07032-015
POWER SUPPLY CURRENT, ICC (mA)
24
20
AMBIENT TEMPERATURE, TA (°C)
Figure 14. Offset Voltage vs. Power Supply Voltage
26
0
07032-017
TA = 25°C
RL = 100Ω
POWER SUPPLY CURRENT, ICC (mA)
OFFSET VOLTAGE, VOS (mV)
1.252
ADN4667
–20
0
20
40
60
80
100
AMBIENT TEMPERATURE, TA (°C)
POWER SUPPLY VOLTAGE, VCC (V)
Figure 19. Differential Propagation Delay vs. Ambient Temperature
Figure 16. Power Supply Current vs. Power Supply Voltage
Rev. B | Page 9 of 16
ADN4667
Data Sheet
400
TA = 25°C
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
TA = 25°C
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
TRANSITION TIME (ps)
80
60
40
380
tTLH
360
tTHL
340
0
3.0
3.1
3.2
3.3
3.4
3.5
320
3.0
3.6
07032-022
20
07032-020
DIFFERENTIAL SKEW, tSKD (ps)
100
3.1
POWER SUPPLY VOLTAGE, VCC (V)
Figure 20. Differential Skew vs. Supply Voltage
400
VCC = 3.3V
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
TRANSITION TIME (ps)
40
3.3
3.4
3.5
3.6
Figure 22. Transition Time vs. Supply Voltage
30
20
VCC = 3.3V
f = 1MHz
CL = 15pF
RL = 100Ω PER DRIVER
380
tTLH
360
tTHL
340
0
–40
–20
0
20
40
60
80
320
–40
100
AMBIENT TEMPERATURE, TA (°C)
07032-023
10
07032-021
DIFFERENTIAL SKEW, tSKD (ps)
50
3.2
POWER SUPPLY VOLTAGE, VCC (V)
–20
0
20
40
60
80
AMBIENT TEMPERATURE, TA (°C)
Figure 21. Differential Skew vs. Ambient Temperature
Figure 23. Transition Time vs. Ambient Temperature
Rev. B | Page 10 of 16
100
Data Sheet
ADN4667
THEORY OF OPERATION
When DIN is high (Logic 1), current flows out of the DOUT+
pin (current source) through RT and back into the DOUT− pin
(current sink). At the receiver, this current develops a positive
differential voltage across RT (with respect to the inverting input)
and gives a Logic 1 at the receiver output. When DIN is low,
DOUT+ sinks current and DOUT− sources current; a negative differential voltage across RT gives a Logic 0 at the receiver output.
The output drive current is between ±2.5 mA and ±4.5 mA
(typically ±3.1 mA), developing between ±250 mV and ±450 mV
across a 100 Ω termination resistor. The received voltage is centered
around the receiver offset of 1.2 V. Therefore, the noninverting
receiver input is typically (1.2 V + [310 mV/2]) = 1.355 V, and the
inverting receiver input is (1.2 V − [310 mV/2]) = 1.045 V for
Logic 1. For Logic 0, the inverting and noninverting output
voltages are reversed. Note that because the differential voltage
reverses polarity, the peak-to-peak voltage swing across RT is
twice the differential voltage.
Current mode drivers offer considerable advantages over
voltage mode drivers such as RS-422 drivers. The operating
current remains fairly constant with increased switching
frequency, whereas that of voltage mode drivers increase
exponentially in most cases. This is caused by the overlap as
internal gates switch between high and low, which causes
currents to flow from the device power supply to ground.
A current mode device simply reverses a constant current
between its two outputs, with no significant overlap currents.
This is similar to emitter-coupled logic (ECL) and positive
emitter-coupled logic (PECL), but without the high quiescent
current of ECL and PECL.
ENABLE INPUTS
The active high and active low enable inputs deactivate all the
current drivers when in the disabled state. This also powers
down the device and reduces the current consumption from
typically 20 mA to typically 2.2 mA. A truth table for the enable
inputs is shown in Table 5.
Table 5. Enable Inputs Truth Table
EN
EN
H
L or open
H
L or open
Any other combination of EN and EN
DIN
DOUT+
DOUT−
L
H
X
ISINK
ISOURCE
Inactive
ISOURCE
ISINK
Inactive
APPLICATIONS INFORMATION
Figure 24 shows a typical application for point-to-point data
transmission using the ADN4667 as the driver and the
ADN4668 as the receiver.
1/4 ADN4667
1/4 ADN4668
EN
EN
EN
EN
DOUT+
RIN+
RT
100Ω
DIN
DOUT–
GND
DOUT
RIN–
GND
Figure 24. Typical Application Circuit
Rev. B | Page 11 of 16
07032-024
The ADN4667 is a quad line driver for low voltage differential
signaling. It takes a single-ended 3 V logic signal and converts
it to a differential current output. The data can then be transmitted for considerable distances, over media such as a twisted pair
cable or PCB backplane, to an LVDS receiver like the ADN4668,
where it develops a voltage across a terminating resistor, RT. This
resistor is chosen to match the characteristic impedance of the
medium, typically around 100 Ω. The differential voltage is
detected by the receiver and converted back into a single-ended
logic signal.
ADN4667
Data Sheet
OUTLINE DIMENSIONS
10.00 (0.3937)
9.80 (0.3858)
4.00 (0.1575)
3.80 (0.1496)
9
16
1
6.20 (0.2441)
5.80 (0.2283)
8
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
0.10
0.50 (0.0197)
0.25 (0.0098)
1.75 (0.0689)
1.35 (0.0531)
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AC
060606-A
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 25. 16-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-16)
Dimensions shown in millimeters and (inches)
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.65
BSC
0.30
0.19
COPLANARITY
0.10
SEATING
PLANE
8°
0°
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 26. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
Rev. B | Page 12 of 16
0.75
0.60
0.45
Data Sheet
ADN4667
ORDERING GUIDE
Model 1, 2
ADN4667ARZ
ADN4667ARZ-REEL7
ADN4667ARUZ
ADN4667ARUZ-REEL7
ADN4667WARZ-REEL7
1
2
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Lead Standard Small Outline Package [SOIC_N]
16-Lead Standard Small Outline Package [SOIC_N]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Standard Small Outline Package [SOIC_N]
Package Option
R-16
R-16
RU-16
RU-16
R-16
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications
AUTOMOTIVE PRODUCTS
The ADN4667W model is available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that this automotive model may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade product shown is available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for this model.
Rev. B | Page 13 of 16
ADN4667
Data Sheet
NOTES
Rev. B | Page 14 of 16
Data Sheet
ADN4667
NOTES
Rev. B | Page 15 of 16
ADN4667
Data Sheet
NOTES
©2008–2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07032-0-3/12(B)
Rev. B | Page 16 of 16
工商网监
湘ICP备2023018690号
