2 A, Low VIN, Low Noise,
CMOS Linear Regulator
ADP1762
Data Sheet
TYPICAL APPLICATION CIRCUITS
APPLICATIONS
GENERAL DESCRIPTION
The ADP1762 is a low noise, low dropout (LDO) linear regulator.
It is designed to operate from a single input supply with an
input voltage as low as 1.10 V, without the requirement of an
external bias supply, to increase efficiency and provide up to
2 A of output current.
The low 62 mV typical dropout voltage at a 2 A load allows the
ADP1762 to operate with a small headroom while maintaining
regulation and providing better efficiency.
Rev. D
CIN
10µF
PG
RPULL-UP
100kΩ
VIN
VOUT
VOUT = 1.5V
COUT
10µF
SENSE
EN
PG
SS
CSS
10nF
ON
OFF
VADJ
VREG
CREG
1µF
REFCAP
CREF
1µF
GND
Figure 1. Fixed Output Operation
ADP1762
VIN = 1.7V
CIN
10µF
PG
RPULL-UP
100kΩ
VIN
VOUT
CSS
10nF
VOUT = 1.5V
COUT
10µF
SENSE
EN
PG
SS
VADJ
VREG
CREG
1µF
ON
OFF
REFCAP
GND
CREF
1µF
RADJ
10kΩ
Figure 2. Adjustable Output Operation
Table 1. Related Devices
Device
ADP1761
ADP1763
Regulation to noise sensitive applications such as radio
frequency (RF) transceivers, analog-to-digital converter
(ADC) and digital-to-analog converter (DAC) circuits,
phase-locked loops (PLLs), voltage controlled oscillators
(VCOs) and clocking integrated circuits
Field-programmable gate array (FPGA) and digital signal
processor (DSP) supplies
Medical and healthcare
Industrial and instrumentation
ADP1762
VIN = 1.7V
12922-002
2 A maximum output current
Low input voltage supply range
VIN = 1.10 V to 1.98 V, no external bias supply required
Fixed output voltage range: VOUT_FIXED = 0.9 V to 1.5 V
Adjustable output voltage range: VOUT_ADJ = 0.5 V to 1.5 V
Ultralow noise: 2 μV rms, 100 Hz to 100 kHz
Noise spectral density
4 nV/√Hz at 10 kHz
3 nV/√Hz at 100 kHz
Low dropout voltage: 62 mV typical at 2 A load
Operating supply current: 4.5 mA typical at no load
±1.5% fixed output voltage accuracy over line, load, and
temperature
Excellent power supply rejection ratio (PSRR) performance
62 dB typical at 10 kHz at 2 A load
46 dB typical at 100 kHz at 2 A load
Excellent load/line transient response
Soft start to reduce inrush current
Optimized for small 10 μF ceramic capacitors
Current-limit and thermal overload protection
Power-good indicator
Precision enable
16-lead, 3 mm × 3 mm LFCSP package
AEC-Q100 qualified for automotive applications
12922-001
FEATURES
ADP1740/
ADP1741
ADP1752/
ADP1753
ADP1754/
ADP1755
Input
Voltage
1.10 V to
1.98 V
1.10 V to
1.98 V
1.6 V to
3.6 V
1.6 V to
3.6 V
1.6 V to
3.6 V
Maximum
Current
1A
Fixed/
Adjustable
Fixed/adjustable
3A
Fixed/adjustable
2A
Fixed/adjustable
0.8 A
Fixed/adjustable
1.2 A
Fixed/adjustable
Package
16-lead
LFCSP
16-lead
LFCSP
16-lead
LFCSP
16-lead
LFCSP
16-lead
LFCSP
The ADP1762 is optimized for stable operation with small 10 μF
ceramic output capacitors. The ADP1762 delivers optimal
transient performance with minimal board area.
The ADP1762 is available in fixed output voltages ranging from
0.9 V to 1.5 V. The output of the adjustable output model can be
set from 0.5 V to 1.5 V through an external resistor connected
between VADJ and ground.
The ADP1762 has an externally programmable soft start time by
connecting a capacitor to the SS pin. Short-circuit and thermal
overload protection circuits prevent damage in adverse conditions.
The ADP1762 is available in a small 16-lead LFCSP for the smallest
footprint solution to meet a variety of applications.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice.
No license is granted by implication or otherwise under any patent or patent rights of Analog
Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2016–2021 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADP1762
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Soft Start Function ..................................................................... 11
Applications ...................................................................................... 1
Adjustable Output Voltage ....................................................... 12
General Description ......................................................................... 1
Enable Feature ............................................................................ 12
Typical Application Circuits ........................................................... 1
Power-Good (PG) Feature ........................................................ 12
Revision History ............................................................................... 2
Applications Information ............................................................. 13
Specifications .................................................................................... 3
Capacitor Selection .................................................................... 13
Input and Output Capacitor: Recommended Specifications . 4
Undervoltage Lockout ............................................................... 14
Absolute Maximum Ratings ........................................................... 5
Current-Limit and Thermal Overload Protection ................ 14
Thermal Data ................................................................................ 5
Thermal Considerations ........................................................... 14
Thermal Resistance/Parameter .................................................. 5
PCB Layout Considerations ..................................................... 17
ESD Caution.................................................................................. 5
Outline Dimensions ....................................................................... 18
Pin Configuration and Function Descriptions ............................ 6
Ordering Guide .......................................................................... 18
Typical Performance Characteristics ............................................. 7
Automotive Products ................................................................ 19
Theory of Operation ...................................................................... 11
REVISION HISTORY
3/2021—Rev. C to Rev. D
Changes to Features Section ........................................................... 1
Change to Undervoltage Lockout, Hysteresis Parameter,
Table 2 ................................................................................................ 4
Changes to Ordering Guide .......................................................... 18
Added Automotive Products Section .......................................... 19
3/2019—Rev. A to Rev. B
Changes to Figure 25 ..................................................................... 11
9/2016—Rev. 0 to Rev. A
Changes to Figure 23 and Figure 24 ............................................ 11
4/2016—Revision 0: Initial Version
3/2020—Rev. B to Rev. C
Changes to Thermal Data Section, Thermal
Resistance/Parameter Section, and Table 5 .................................. 5
Rev. D | Page 2 of 19
Data Sheet
ADP1762
SPECIFICATIONS
VIN = VOUT + 0.2 V or VIN = 1.1 V, whichever is greater, ILOAD = 10 mA, CIN = 10 μF, COUT = 10 μF, CREF = 1 μF, CREG = 1 μF, TA = 25°C,
Minimum and maximum limits at TJ = −40°C to +125°C, unless otherwise noted.
Table 2.
Parameter
INPUT VOLTAGE SUPPLY RANGE
CURRENT
Operating Supply Current
Shutdown Current
OUTPUT NOISE1
Noise Spectral Density
POWER SUPPLY REJECTION RATIO1
Symbol
VIN
Test Conditions/Comments
TJ = −40°C to +125°C
IGND
ILOAD = 0 μA
ILOAD = 10 mA
ILOAD = 100 mA
ILOAD = 2 A
EN = GND
TJ = −40°C to +85°C,
VIN = (VOUT + 0.2 V) to 1.98 V
TJ = 85°C to 125°C,
VIN = (VOUT + 0.2 V) to 1.98 V
10 Hz to 100 kHz, VIN = 1.1 V, VOUT = 0.9 V
100 Hz to 100 kHz, VIN = 1.1 V, VOUT = 0.9 V
10 Hz to 100 kHz, VIN = 1.5 V, VOUT = 1.3 V
100 Hz to 100 kHz, VIN = 1.5 V, VOUT = 1.3 V
10 Hz to 100 kHz, VIN = 1.7 V, VOUT = 1.5 V
100 Hz to 100 kHz, VIN = 1.7 V, VOUT = 1.5 V
VOUT = 0.9 V to 1.5 V, ILOAD = 100 mA
At 10 kHz
At 100 kHz
ILOAD = 2 A, modulated VIN
10 kHz, VOUT = 1.3 V, VIN = 1.6 V
100 kHz, VOUT = 1.3 V, VIN = 1.6 V
1 MHz, VOUT = 1.3 V, VIN = 1.6 V
10 kHz, VOUT = 0.9 V, VIN = 1.2 V
100 kHz, VOUT = 0.9 V, VIN = 1.2 V
1 MHz, VOUT = 0.9 V, VIN = 1.2 V
IGND-SD
OUTNOISE
OUTNSD
PSRR
OUTPUT VOLTAGE
Output Voltage Range
Fixed Output Voltage Accuracy
Typ
Max
1.98
Unit
V
4.5
4.9
5.5
9.4
2
8
8
8.5
14
180
mA
mA
mA
mA
μA
μA
800
μA
12
2
15
2
21
2
μV rms
μV rms
μV rms
μV rms
μV rms
μV rms
4
3
nV/√Hz
nV/√Hz
62
46
39
63
46
34
dB
dB
dB
dB
dB
dB
TA = 25°C
VOUT_FIXED
VOUT_ADJ
VOUT
ADJUSTABLE PIN CURRENT
IADJ
ADJUSTABLE OUTPUT VOLTAGE GAIN FACTOR
AD
REGULATION
Line Regulation
Load Regulation2
DROPOUT VOLTAGE3
Min
1.10
ΔVOUT/ΔVIN
ΔVOUT/ΔIOUT
VDROPOUT
ILOAD = 100 mA, TA = 25°C
10 mA < ILOAD < 2 A, VIN = (VOUT + 0.2 V) to
1.98 V, TJ = 0°C to 85°C
10 mA < ILOAD < 2 A, VIN = (VOUT + 0.2 V) to
1.98 V
TA = 25°C
VIN = (VOUT + 0.2 V) to 1.98 V
TA = 25°C
VIN = (VOUT + 0.2 V) to 1.98 V
VIN = (VOUT + 0.2 V) to 1.98 V
ILOAD = 10 mA to 2 A
ILOAD = 100 mA, VOUT = 1.2 V
ILOAD = 2 A, VOUT = 1.2 V
Rev. D | Page 3 of 19
0.9
0.5
−0.5
−1
1.5
1.5
+0.5
+1.5
V
V
%
%
−1.5
+1.5
%
50.5
51.0
μA
μA
49.5
48.8
50.0
50.0
3.0
2.95
3.055
−0.15
+0.15
0.41
23
95
0.15
12
62
%/V
%/A
mV
mV
ADP1762
Parameter
START-UP TIME1, 4
SOFT START CURRENT
CURRENT-LIMIT THRESHOLD5
THERMAL SHUTDOWN
Threshold
Hysteresis
POWER-GOOD (PG) OUTPUT THRESHOLD
Output Voltage
Falling
Rising
PG OUTPUT
Output Voltage Low
Leakage Current
Delay1
PRECISION EN INPUT
Logic Input
High
Low
Input Logic Hysteresis
Input Leakage Current
Input Delay Time
UNDERVOLTAGE LOCKOUT
Input Voltage
Rising
Falling
Hysteresis
Data Sheet
Symbol
tSTART-UP
ISS
ILIMIT
Test Conditions/Comments
ILOAD = 10 nF, VOUT = 1 V
1.1 V ≤ VIN ≤ 1.98 V
TSSD
TSSD-HYS
TJ rising
150
15
°C
°C
PGFALL
PGRISE
1.1 V ≤ VIN ≤ 1.98 V
1.1 V ≤ VIN ≤ 1.98 V
−7.5
−5
%
%
PGLOW
IPG-LKG
PGDELAY
1.1 V ≤ VIN ≤ 1.98 V, IPG ≤ 1 mA
1.1 V ≤ VIN ≤ 1.98 V
ENRISING to PGRISING
1.1 V ≤ VIN ≤ 1.98 V
0.01
0.75
ENHIGH
ENLOW
ENHYS
IEN-LKG
tIEN-DLY
UVLO
UVLORISE
UVLOFALL
UVLOHYS
Min
8
2.2
595
550
EN = VIN or GND
From EN rising from 0 V to VIN to 0.1 × VOUT
TJ = −40°C to +125°C
TJ = −40°C to +125°C
0.87
Typ
0.6
10
3
Max
12
4
Unit
ms
μA
A
0.35
1
V
μA
ms
625
580
45
0.01
100
690
630
mV
mV
mV
μA
μs
1.01
0.93
80
1.06
1
V
V
mV
1
Guaranteed by design and characterization; not production tested.
Based on an endpoint calculation using 10 mA and 2 A loads.
3
Dropout voltage is defined as the input to output voltage differential when the input voltage is set to the nominal output voltage, which applies only for output
voltages above 1.1 V.
4
Start-up time is defined as the time from the rising edge of EN to VOUT being at 90% of the nominal value.
5
Current-limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 1.0 V
output voltage is defined as the current that causes the output voltage to drop to 90% of 1.0 V, or 0.9 V.
2
INPUT AND OUTPUT CAPACITOR: RECOMMENDED SPECIFICATIONS
Table 3.
Parameter
CAPACITANCE1
Input
Output
Regulator
Reference
CAPACITOR EQUIVALENT SERIES RESISTANCE (ESR)
CIN, COUT
CREG, CREF
1
Symbol
CIN
COUT
CREG
CREF
RESR
Test Conditions/Comments
TA = −40°C to +125°C
Min
Typ
7.0
7.0
0.7
0.7
10
10
1
1
Max
Unit
μF
μF
μF
μF
TA = −40°C to +125°C
0.001
0.001
0.5
0.2
Ω
Ω
The minimum input and output capacitance must be >7.0 μF over the full range of the operating conditions. Consider the full range of the operating conditions in the
application during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended. Y5V and Z5U
capacitors are not recommended for use with any LDO.
Rev. D | Page 4 of 19
Data Sheet
ADP1762
ABSOLUTE MAXIMUM RATINGS
Table 4.
Parameter
VIN to GND
EN to GND
VOUT to GND
SENSE to GND
VREG to GND
REFCAP to GND
VADJ to GND
SS to GND
PG to GND
Storage Temperature Range
Operating Temperature Range
Operating Junction Temperature
Lead Temperature (Soldering, 10 sec)
Rating
−0.3 V to +2.16 V
−0.3 V to +3.96 V
−0.3 V to VIN
−0.3 V to VIN
−0.3 V to VIN
−0.3 V to VIN
−0.3 V to VIN
−0.3 V to VIN
−0.3 V to +3.96 V
−65°C to +150°C
−40°C to +125°C
125°C
300°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL DATA
ΨJB of the package is based on modeling and calculation using a
4-layer board. JESD51-12, Guidelines for Reporting and Using
Electronic Package Thermal Information, states that thermal
characterization parameters are not the same as thermal
resistances. ΨJB measures the component power flowing
through multiple thermal paths rather than a single path as in
thermal resistance, θJB. Therefore, ΨJB thermal paths include
convection from the top of the package as well as radiation
from the package, factors that make ΨJB more useful in realworld applications.
THERMAL RESISTANCE/PARAMETER
Values shown in Table 5 are calculated in compliance with JEDEC
standards for thermal reporting. θJA is the natural convection
junction to ambient thermal resistance measured in a one cubic
foot sealed enclosure. θJC is the junction to case thermal resistance.
θJB is the junction to board thermal resistance. ΨJB is the junction to
board thermal characterization parameter. ΨJT is the junction to
top thermal characterization parameter.
In applications where high maximum power dissipation exists,
close attention to thermal board design is required. Thermal
resistance/parameter values may vary, depending on the PCB
material, layout, and environmental conditions.
Table 5. Thermal Resistance/Parameter
Absolute maximum ratings apply individually only, not in
combination. The ADP1762 can be damaged when the junction
temperature limits are exceeded. The use of appropriate thermal
management techniques is recommended to ensure that the
maximum junction temperature does not exceed the limits shown
in Table 4.
Package
Type
CP-16-221
Use the following equation to calculate the junction temperature
(TJ) from the board temperature (TBOARD) or package top
temperature (TTOP)
ESD CAUTION
1
θJA
50.95
θJB
29.31
θJC-T
49.53
θJC-B
8.53
ΨJB
29.31
ΨJT
0.3
Unit
°C/W
Thermal resistance/parameter simulated values are based on a JEDEC 2S2P
thermal test board for ΨJT, ΨJB, θJA and θJB and a JEDEC 1S0P thermal test
board for θJC with four thermal vias. See JEDEC JESD51-12.
TJ = TBOARD + (PD × ΨJB)
TJ = TTOP + (PD × ΨJT)
ΨJB is the junction to board thermal characterization parameter
and ΨJT is the junction to top thermal characterization
parameter with units of °C/W.
Rev. D | Page 5 of 19
ADP1762
Data Sheet
13 SENSE
14 SS
16 EN
15 PG
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
VIN 1
VIN 3
12 VOUT
ADP1762
TOP VIEW
(Not to Scale)
10 VOUT
GND 7
VOUT
VADJ 8
VREG 6
9
REFCAP 5
VIN 4
11 VOUT
NOTES
1. THE EXPOSED PAD IS ELECTRICALLY
CONNECTED TO GND. IT IS RECOMMENDED
THAT THIS PAD BE CONNECTED TO A GROUND
PLANE ON THE PCB. THE EXPOSED PAD IS
ON THE BOTTOM OF THE PACKAGE.
12922-003
VIN 2
Figure 3. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
1 to 4
Mnemonic
VIN
5
REFCAP
6
VREG
7
8
GND
VADJ
9 to 12
VOUT
13
SENSE
14
15
SS
PG
16
EN
EP
Description
Regulator Input Supply. Bypass VIN to GND with a 10 μF or greater capacitor. Note that all four VIN pins must be
connected to the source supply.
Reference Filter Capacitor. Connect a 1 μF capacitor from the REFCAP pin to ground. Do not connect a load to
ground.
Regulated Input Supply to LDO Amplifier. Bypass VREG to GND with a 1 μF or greater capacitor. Do not connect
a load to ground.
Ground.
Adjustable Voltage Pin for the Adjustable Output Option. Connect a 10 kΩ external resistor between the VADJ
pin and ground to set the output voltage to 1.5 V. For the fixed output option, leave this pin floating.
Regulated Output Voltage. Bypass VOUT to GND with a 10 μF or greater capacitor. Note that all four VOUT pins
must be connected to the load.
Sense Input. The SENSE pin measures the actual output voltage at the load and feeds it to the error amplifier.
Connect VSENSE as close to the load as possible to minimize the effect of IR voltage drop between VOUT and the
load.
Soft Start Pin. A 10 nF capacitor connected to the SS pin and ground sets the start-up time to 0.6 ms.
Power-Good Output. This open-drain output requires an external pull-up resistor. If the device is in shutdown
mode, current-limit mode, or thermal shutdown mode, or if VOUT falls below 90% of the nominal output
voltage, the PG pin immediately transitions low.
Enable Input. Drive the EN pin high to turn on the regulator. Drive the EN pin low to turn off the regulator. For
automatic startup, connect the EN pin to the VIN pin.
Exposed Pad. The exposed pad is electrically connected to GND. It is recommended that this pad be connected
to a ground plane on the PCB. The exposed pad is on the bottom of the package.
Rev. D | Page 6 of 19
Data Sheet
ADP1762
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = 1.5 V, VOUT = 1.3 V, TA = 25°C, unless otherwise noted.
OUTPUT VOLTAGE (V)
1.303
14
NO LOAD
ILOAD = 10mA
ILOAD = 100mA
ILOAD = 1A
ILOAD = 2A
12
GROUND CURRENT (mA)
1.305
1.301
1.299
10
8
6
4
1.297
–25
0
25
50
75
100
125
150
JUNCTION TEMPERATURE (°C)
0
–50
12922-004
1.295
–50
NO LOAD
ILOAD = 100mA
ILOAD = 1A
–25
ILOAD = 10mA
ILOAD = 500mA
ILOAD = 2A
0
25
50
75
100
125
150
JUNCTION TEMPERATURE (°C)
12922-007
2
Figure 7. Ground Current vs. Junction Temperature
Figure 4. Output Voltage (VOUT) vs. Junction Temperature
12
1.3035
1.3030
GROUND CURRENT (mA)
OUTPUT VOLTAGE (V)
10
1.3025
1.3020
8
6
4
0.1
1
10
LOAD CURRENT (A)
0
0.01
12922-005
12
= 100mA
= 1A
= 1.5A
= 2A
GROUND CURRENT (mA)
10
1.306
1.304
1.302
8
6
4
2
1.300
1.298
1.5
1.6
10
Figure 8. Ground Current vs. Load Current
1.7
1.8
1.9
INPUT VOLTAGE (V)
2.0
12922-006
OUTPUT VOLTAGE (V)
1.308
ILOAD
ILOAD
ILOAD
ILOAD
1
LOAD CURRENT (A)
Figure 5. Output Voltage (VOUT) vs. Load Current
1.310
0.1
0
1.5
NO LOAD
ILOAD = 100mA
ILOAD = 1A
1.6
ILOAD = 10mA
ILOAD = 500mA
ILOAD = 2A
1.7
1.8
1.9
INPUT VOLTAGE (V)
Figure 9. Ground Current vs. Input Voltage
Figure 6. Output Voltage vs. Input Voltage
Rev. D | Page 7 of 19
2
12922-009
1.3015
0.01
12922-008
2
ADP1762
160
140
10
GROUND CURRENT (mA)
180
SHUTDOWN CURRENT (µA)
12
VIN = 1.5V
VIN = 1.7V
VIN = 1.9V
VIN = 1.6V
VIN = 1.8V
VIN = 1.98V
120
100
80
60
40
8
6
4
20
2
0
–25
0
25
50
75
100
125
150
JUNCTION TEMPERATURE (°C)
0
1.1
12922-010
–20
–50
Figure 10. Shutdown Current vs. Junction Temperature at
Various Input Voltages (VIN)
NO LOAD
ILOAD = 100mA
ILOAD = 1A
1.2
ILOAD = 10mA
ILOAD = 500mA
ILOAD = 2A
1.3
1.4
1.5
1.6
INPUT VOLTAGE (V)
12922-012
200
Data Sheet
Figure 13. Ground Current vs. Input Voltage (in Dropout), VOUT = 1.3 V
70
3A/µs SLEW RATE
DROPOUT VOLTAGE (mV)
60
50
2
ILOAD
40
30
1
VOUT
20
1
10
LOAD CURRENT (A)
CH1 50.0mV
12922-111
0
0.1
Figure 11. Dropout Voltage vs. Load Current, VOUT = 1.3 V
B
W
CH2 1.00A
M4.00µs
T 18.70%
A CH2
640mA
12922-114
10
Figure 14. Load Transient Response, COUT = 10 μF, VIN = 1.7 V, VOUT = 1.3V
1.35
OUTPUT VOLTAGE (V)
1.30
ILOAD
ILOAD
ILOAD
ILOAD
= 100mA
= 1A
= 1.5A
= 2A
3A/µs SLEW RATE
2
ILOAD
1.25
1.20
1
VIN
1.3
1.4
INPUT VOLTAGE (V)
1.5
Figure 12. Output Voltage vs. Input Voltage (in Dropout), VOUT = 1.3 V
CH1 50.0mV
CH2 1.00A
M4.00µs
T 19.00%
A CH2
640mA
12922-115
1.10
1.2
12922-112
1.15
Figure 15. Load Transient Response, COUT = 47 μF, VIN = 1.7 V, VOUT = 1.3 V
Rev. D | Page 8 of 19
Data Sheet
ADP1762
–10
VIN = 1.1V
VIN = 1.2V
VIN = 1.3V
VIN = 1.4V
VIN = 1.5V
VIN = 1.6V
–20
1V/µs SLEW RATE
–30
VIN
PSRR (dB)
–40
VOUT
1
2
–50
–60
–70
–80
–90
CH2 500mV
M2.00µs
T 17.50%
A CH2
1.68V
–110
1
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 19. Power Supply Rejection Ratio (PSRR) vs. Frequency for Various VIN,
VOUT = 0.9 V, Load Current = 2 A
Figure 16. Line Transient Response, Load Current = 2 A,
VIN = 1.5 V to 1.98 V Step, VOUT = 1.3 V
–10
16
VOUT = 1.3V (10Hz TO 100kHz)
VIN = 1.5V
VIN = 1.6V
VIN = 1.7V
VIN = 1.8V
VIN = 1.9V
VIN = 1.98V
–20
14
–30
12
–40
10
PSRR (dB)
NOISE (µV rms)
10
12922-019
CH1 5.00mV
12922-116
–100
8
6
–50
–60
–70
–80
4
–90
VOUT = 1.3V (100Hz TO 100kHz)
–100
1
10
LOAD CURRENT (A)
–110
1
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 20. Power Supply Rejection Ratio (PSRR) vs. Frequency for
Various VIN, VOUT = 1.3 V, Load Current = 2 A
Figure 17. Noise vs. Load Current for Various Output Voltages
–10
10k
VIN = 1.7V
VIN = 1.8V
VIN = 1.9V
VIN = 1.98V
–20
–30
1k
–40
PSRR (dB)
100
10
–50
–60
–70
–80
–90
1
100
–100
1k
FREQUENCY (Hz)
10k
100k
Figure 18. Noise Spectral Density vs. Frequency for Various Output Voltages,
ILOAD = 100 mA
Rev. D | Page 9 of 19
–110
1
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 21. Power Supply Rejection Ratio (PSRR) vs. Frequency for
Various VIN, VOUT = 1.5 V, Load Current = 2 A
12922-021
0.1
10
VOUT = 0.9V
VOUT = 1.3V
VOUT = 1.5V
12922-015
NOISE SPECTRAL DENSITY (nV/√Hz)
10
12922-020
0
0.1
12922-013
2
ADP1762
–10
Data Sheet
ILOAD = 200mA
ILOAD = 500mA
ILOAD = 1A
ILOAD = 2A
–20
–30
PSRR (dB)
–40
–50
–60
–70
–80
–90
–110
1
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
12922-022
–100
Figure 22. Power Supply Rejection Ratio (PSRR) vs. Frequency for
Various Loads, VOUT = 1.3 V, VIN = 1.6 V
Rev. D | Page 10 of 19
Data Sheet
ADP1762
THEORY OF OPERATION
The ADP1762 is an LDO, low noise linear regulator that uses an
advanced proprietary architecture to achieve high efficiency
regulation. It also provides high PSRR and excellent line and load
transient response using a small 10 F ceramic output capacitor.
The device operates from a 1.10 V to 1.98 V input rail to provide
up to 2 A of output current. Supply current in shutdown mode
is 2 μA.
ADP1762
VIN
EN
INTERNAL
BIAS SUPPLY
SS BLOCK
For applications that require a controlled startup, the ADP1762
provides a programmable soft start function. The programmable
soft start is useful for reducing inrush current upon startup and
for providing voltage sequencing. To implement soft start, connect
a small ceramic capacitor from SS to ground. At startup, a 10 μA
current source charges this capacitor. The voltage at SS limits the
ADP1762 start-up output voltage, providing a smooth ramp-up
to the nominal output voltage. To calculate the start-up time for
the fixed output and adjustable output, use the following equations:
tSTART-UP_FIXED = tDELAY + VREF × (CSS/ISS)
SS
REFCAP
Figure 23. Functional Block Diagram, Fixed Output
ADP1762
VIN
VREG
SOFT START FUNCTION
PG
REFERENCE,
BIAS
GND
SENSE
12922-023
VREG
VOUT
SHORT-CIRCUIT,
THERMAL
PROTECTION
The ADP1762 uses the EN pin to enable and disable the VOUT
pin under normal operating conditions. When EN is high, VOUT
turns on. When EN is low, VOUT turns off. For automatic
startup, tie EN to VIN.
tSTART-UP_ADJ = tDELAY + VADJ × (CSS/ISS)
(2)
where:
tDELAY is a fixed delay of 100 μs.
VREF is a 0.5 V internal reference for the fixed output model option.
CSS is the soft start capacitance from SS to GND.
ISS is the current sourced from SS (10 μA).
VADJ is the voltage at the VADJ pin equal to RADJ × IADJ.
1.7
VOUT
INTERNAL
BIAS SUPPLY
SHORT-CIRCUIT,
THERMAL
PROTECTION
1.5
SENSE
1.3
IADJ
1.1
VOUT, EN (V)
EN
VADJ
(1)
3×
0.9
0.7
PG
0.5
0.3
SS
Figure 24. Functional Block Diagram, Adjustable Output
0.3
0.8
1.3
1.8
TIME (ms)
Figure 25. Fixed VOUT Ramp-Up with External Soft Start Capacitor (VOUT, EN) vs. Time
2.0
Internally, the ADP1762 consists of a reference, an error amplifier,
and a pass device. The output current is delivered via the pass
device, which is controlled by the error amplifier, forming a
negative feedback system that ideally drives the feedback
voltage to equal the reference voltage. If the feedback voltage is
lower than the reference voltage, the negative feedback drives
more current, increasing the output voltage. If the feedback
voltage is higher than the reference voltage, the negative feedback
drives less current, decreasing the output voltage.
The ADP1762 is available in output voltages ranging from 0.9 V to
1.5 V for a fixed output. Contact a local Analog Devices, Inc., sales
representative for other fixed voltage options. The adjustable
output option can be set from 0.5 V to 1.5 V.
Rev. D | Page 11 of 19
1.5
1.0
0.5
EN
VOUT = 0.5V; CSS
VOUT = 0.5V; CSS
VOUT = 1.5V; CSS
VOUT = 1.5V; CSS
0
–0.5
–0.2
0.3
0.8
1.3
= 10nF
= 22nF
= 10nF
= 22nF
1.8
TIME (ms)
Figure 26. Adjustable VOUT Ramp-Up with External Soft Start
Capacitor (VOUT, EN) vs. Time
12922-226
REFCAP
–0.1
–0.2
VOUT, EN (V)
SS BLOCK
12919-024
GND
12922-025
EN
CSS = 0nF
CSS = 10nF
CSS = 22nF
0.1
ADP1762
Data Sheet
ADJUSTABLE OUTPUT VOLTAGE
POWER-GOOD (PG) FEATURE
The output voltage of the ADP1762 can be set over a 0.5 V to
1.5 V range. Connect a resistor (RADJ) from the VADJ pin to
ground to set the output voltage. To calculate the output
voltage, use the following equation:
The ADP1762 provides a power-good pin (PG) to indicate the
status of the output. This open-drain output requires an external
pull-up resistor that can be connected to VIN or VOUT. If the
device is in shutdown mode, current-limit mode, or thermal
shutdown, or if it falls below 90% of the nominal output
voltage, PG immediately transitions low. During soft start, the
rising threshold of the power-good signal is 95% of the nominal
output voltage.
VOUT = AD × (RADJ × IADJ)
(3)
where:
AD is the gain factor with a typical value of 3.0 between the
VADJ pin and VOUT pin.
IADJ is the 50.0 μA constant current out of the VADJ pin.
ENABLE FEATURE
The ADP1762 uses the EN pin to enable and disable the VOUT
pins under normal operating conditions. As shown in Figure 27,
when a rising voltage on EN crosses the active threshold, VOUT
turns on. When a falling voltage on EN crosses the inactive
threshold, VOUT turns off.
EN
The open-drain output is held low when the ADP1762 has a
sufficient input voltage to turn on the internal PG transistor. An
optional soft start delay can be detected. The PG transistor is
terminated via a pull-up resistor to VOUT or VIN.
Power-good accuracy is 92.5% of the nominal regulator output
voltage when this voltage is rising, with a 95% trip point when
this voltage is falling.
Regulator input voltage brownouts or glitches trigger a power
no good if VOUT falls below 92.5%.
A normal power-down triggers a power good when VOUT is at 95%.
VOUT
VIN
1
VOUT
2
CH1 200mV
B
W
CH2 200mV
B
W
M4.0ms
A CH1
T
8.26ms
768mV
12922-026
1
PG
4
As shown in Figure 28, the EN pin has hysteresis built in. This
hysteresis prevents on/off oscillations that can occur due to
noise on the EN pin as it passes through the threshold points.
CH1 1.00V
CH2 1.00V
CH4 1.00V
M100µs
A CH4
T 228.0000µs
420mV
12922-027
Figure 27. Typical EN Pin Operation
Figure 29. Typical PG Behavior vs. VOUT, VIN Rising (VOUT = 1.3 V)
1.4
1.3
VIN
1.2
1.0
1
0.9
VOUT
0.8
0.7
0.6
2
PG
0.5
0.4
0.3
0.1
0
0.55
0.56
0.57
0.58
0.59
0.60
0.61
0.62
0.63
0.64
0.65
EN VOLTAGE (V)
Figure 28. Output Voltage vs. Typical EN Pin Voltage, VOUT = 1.3 V
Rev. D | Page 12 of 19
CH1 1.00V
CH2 1.00V
CH4 1.00V
M200µs
A CH1
T 0.000000s
3.00V
12922-128
4
0.2
12922-127
OUTPUT VOLTAGE (V)
1.1
Figure 30. Typical PG Behavior vs. VOUT, VIN Falling (VOUT = 1.3 V)
Data Sheet
ADP1762
APPLICATIONS INFORMATION
CAPACITOR SELECTION
Input and Output Capacitor Properties
Output Capacitor
Use any good quality ceramic capacitors with the ADP1762, as
long as they meet the minimum capacitance and maximum
ESR requirements. Ceramic capacitors are manufactured with a
variety of dielectrics, each with different behavior over temperature
and applied voltage. Capacitors must have a dielectric adequate to
ensure the minimum capacitance over the necessary temperature
range and dc bias conditions. X5R or X7R dielectrics with a
voltage rating of 6.3 V or 10 V are recommended. Y5V and
Z5U dielectrics are not recommended, due to poor temperature
and dc bias characteristics.
The ADP1762 is designed for operation with small, space-saving
ceramic capacitors, but it can function with most commonly
used capacitors as long as care is taken with the effective series
resistance (ESR) value. The ESR of the output capacitor affects
the stability of the LDO control loop. A minimum of 10 μF
capacitance with an ESR of 500 mΩ or less is recommended to
ensure the stability of the ADP1762. Transient response to changes
in load current is also affected by output capacitance. Using a
larger value of output capacitance improves the transient response
of the ADP1762 to large changes in load current. Figure 31 and
Figure 32 show the transient responses for output capacitance
values of 10 μF and 47 μF, respectively.
2
ILOAD
Figure 33 shows the capacitance vs. bias voltage characteristics
of an 0805 case, 10 μF, 10 V, X5R capacitor. The voltage stability of
a capacitor is strongly influenced by the capacitor size and voltage
rating. In general, a capacitor in a larger package or with a higher
voltage rating exhibits better stability. The temperature variation
of the X5R dielectric is about ±15% over the −40°C to +85°C
temperature range and is not a function of package size or
voltage rating.
12
VOUT
B
W
CH2 1.00A
M1.00µs
T 18.70%
A CH2
640mA
CAPACITANCE (µF)
CH1 50.0mV
10
12922-130
1
8
6
4
Figure 31. Output Transient Response, COUT = 10 μF
0
2
1
0
1
2
3
4
5
DC BIAS VOLTAGE (V)
ILOAD
6
12922-032
2
Figure 33. Capacitance vs. DC Bias Voltage
Use Equation 4 to determine the worst case capacitance,
accounting for capacitor variation over temperature, component
tolerance, and voltage.
VIN
CEFF = COUT × (1 − Tempco) × (1 − TOL)
CH2 1.00A
M1.00µs
T 19.00%
A CH2
640mA
where:
CEFF is the effective capacitance at the operating voltage.
COUT is the output capacitor.
Tempco is the worst case capacitor temperature coefficient.
TOL is the worst case component tolerance.
12922-131
CH1 50.0mV
(4)
Figure 32. Output Transient Response, COUT = 47 μF
Input Bypass Capacitor
Connecting a 10 μF capacitor from the VIN pin to the GND pin to
ground reduces the circuit sensitivity to the PCB layout, especially
when long input traces or high source impedance are encountered.
If output capacitance greater than 10 μF is required, it is
recommended that the input capacitor be increased to match it.
In this example, the worst case temperature coefficient (tempco)
over −40°C to +85°C is assumed to be 15% for an X5R dielectric.
The tolerance of the capacitor (TOL) is assumed to be 10%, and
COUT = 10 μF at 1.0 V, as shown in Figure 33.
Rev. D | Page 13 of 19
ADP1762
Data Sheet
Substituting these values in Equation 4 yields
THERMAL CONSIDERATIONS
CEFF = 10 μF × (1 − 0.15) × (1 − 0.1) = 7.65 μF
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over temperature
and tolerance at the chosen output voltage.
To guarantee the performance of the ADP1762, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
UNDERVOLTAGE LOCKOUT
The ADP1762 has an internal undervoltage lockout circuit that
disables all inputs and the output when the input voltage is less
than approximately 1.06 V. The UVLO ensures that the ADP1762
inputs and the output behave in a predictable manner during
power-up.
CURRENT-LIMIT AND THERMAL OVERLOAD
PROTECTION
The ADP1762 is protected against damage due to excessive power
dissipation by current-limit and thermal overload protection
circuits. The ADP1762 is designed to reach the current limit
when the output load reaches 3 A (typical). When the output
load exceeds 3 A, the output voltage is reduced to maintain a
constant current limit.
Thermal overload protection is included, which limits the
junction temperature to a maximum of 150°C (typical). Under
extreme conditions (that is, high ambient temperature and power
dissipation) when the junction temperature begins to rise above
150°C, the output is turned off, reducing the output current to
zero. When the junction temperature drops below 135°C (typical),
the output is turned on again, and the output current is restored to
the nominal value.
Consider the case where a hard short from VOUT to ground
occurs. At first, the ADP1762 reaches the current limit so that
only 3 A is conducted into the short circuit. If self heating of the
junction becomes great enough to cause the temperature to rise
above 150°C, thermal shutdown activates, turning off the output
and reducing the output current to zero. As the junction
temperature cools and drops below 135°C, the output turns
on and conducts 3 A into the short circuit, again causing the
junction temperature to rise above 150°C. This thermal oscillation
between 135°C and 150°C causes a current oscillation between
3 A and 0 A that continues as long as the short circuit remains
at the output.
Current-limit and thermal overload protections are intended
to protect the device against accidental overload conditions.
For reliable operation, limit the device power externally so that
junction temperatures do not exceed 125°C.
To guarantee reliable operation, the junction temperature of
the ADP1762 must not exceed 125°C. To ensure that the
junction temperature stays below this maximum value, the user
needs to be aware of the parameters that contribute to junction
temperature changes. These parameters include ambient
temperature, power dissipation in the power device, and
thermal resistance between the junction and ambient air (θJA).
The θJA value is dependent on the package assembly compounds
used and the amount of copper to which the GND pin and the
exposed pad (EPAD) of the package are soldered on the PCB.
Table 7 shows typical θJA values for the 16-lead LFCSP for
various PCB copper sizes. Table 8 shows typical ΨJB values for
the 16-lead LFCSP.
Table 7. Typical θJA Values
Copper Size (mm2)
25
100
500
1000
6400
θJA (°C/W), LFCSP
138.1
102.9
76.9
67.3
56
Table 8. Typical ΨJB Values
Copper Size (mm2)
100
500
1000
ΨJB (°C/W) at 1 W
33.3
28.9
28.5
To calculate the junction temperature of the ADP1762, use the
following equation:
TJ = TA + (PD × θJA)
(5)
where:
TA is the ambient temperature.
PD is the power dissipation in the die, given by
PD = ((VIN − VOUT) × ILOAD) + (VIN × IGND)
where:
VIN and VOUT are the input and output voltages, respectively.
ILOAD is the load current.
IGND is the ground current.
As shown in Equation 6, for a given ambient temperature
and computed power dissipation, a minimum copper size
requirement exists for the PCB to ensure that the junction
temperature does not rise above 125°C.
Rev. D | Page 14 of 19
(6)
Data Sheet
ADP1762
140
Figure 34 through Figure 39 show the junction temperature
calculations for the different ambient temperatures, load
currents, VIN to VOUT differentials, and areas of PCB copper.
TJ MAX
JUNCTION TEMPERATURE (°C)
120
140
TJ MAX
2A
100
1A
80
500mA
60
40
100
500mA
80
100mA
60
10mA
40
20
0
0.2
100mA
0.4
0.6
10mA
20
0.8
1.0
1.2
1.4
1.6
VIN – VOUT (V)
12922-037
JUNCTION TEMPERATURE (°C)
120
1A
2A
Figure 37. 6400 mm2 of PCB Copper, TA = 50°C
0.4
0.6
0.8
1.0
1.2
1.4
1.6
VIN – VOUT (V)
140
TJ MAX
100
500mA
80
2A
1A
500mA
100
80
100mA
60
10mA
40
20
60
0
0.2
100mA
40
0.4
0.6
10mA
20
0.8
1.0
1.2
1.4
1.6
VIN – VOUT (V)
12922-038
JUNCTION TEMPERATURE (°C)
1A
2A
TJ MAX
120
JUNCTION TEMPERATURE (°C)
Figure 34. 6400 mm2 of PCB Copper, TA = 25°C
120
140
12922-034
0
0.2
Figure 38. 500 mm2 of PCB Copper, TA = 50°C
0.4
0.6
0.8
1.0
1.2
1.4
1.6
VIN – VOUT (V)
140
TJ MAX
500mA
100
80
2A
1A
500mA
100
80
100mA
60
10mA
40
20
60
0
0.2
40
0.6
0.8
1.0
1.2
1.4
VIN – VOUT (V)
10mA
20
0.4
Figure 39. 25 mm2 of PCB Copper, TA = 50°C
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
VIN – VOUT (V)
1.6
Figure 36. 25 mm2 of PCB Copper, TA = 25°C
Rev. D | Page 15 of 19
1.6
12922-039
100mA
12922-036
JUNCTION TEMPERATURE (°C)
1A
2A
TJ MAX
120
JUNCTION TEMPERATURE (°C)
Figure 35. 500 mm2 of PCB Copper, TA = 25°C
120
140
12922-035
0
0.2
ADP1762
Data Sheet
Figure 40 through Figure 43 show the junction temperature
calculations for the different board temperatures, load currents,
VIN to VOUT differentials, and areas of PCB copper.
TJ MAX
80
1A
60
500mA
40
0
0.2
120
100mA
10mA
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.6
VIN – VOUT (V)
100
2A
Figure 42. 1000 mm2 of PCB Copper, TB = 25°C
140
80
1A
120
500mA
40
100mA
10mA
20
0.4
0.6
0.8
1.0
1.2
1.4
1.6
VIN – VOUT (V)
Figure 40. 500 mm2 of PCB Copper, TB = 25°C
JUNCTION TEMPERATURE (°C)
60
12922-040
JUNCTION TEMPERATURE (°C)
2A
20
140
0
0.2
100
12922-042
(7)
TJ MAX
120
12922-043
TJ = TB + (PD × ΨJB)
140
JUNCTION TEMPERATURE (°C)
In cases where the board temperature is known, the thermal
characterization parameter (ΨJB) can be used to estimate the
junction temperature rise. The maximum junction temperature
(TJ) is calculated from the board temperature (TB) and power
dissipation (PD) using the following formula:
2A
100
1A
80
500mA
60
100mA
10mA
40
20
140
TJ MAX
0
0.2
2A
100
80
500mA
60
100mA
10mA
40
20
0.4
0.6
0.8
0.6
0.8
1.0
1.2
1.4
Figure 43. 1000 mm2 of PCB Copper, TB = 50°C
1A
0
0.2
0.4
VIN – VOUT (V)
1.0
1.2
1.4
VIN – VOUT (V)
1.6
12922-041
JUNCTION TEMPERATURE (°C)
120
Figure 41. 500 mm2 of PCB Copper, TB = 50°C
Rev. D | Page 16 of 19
Data Sheet
ADP1762
PCB LAYOUT CONSIDERATIONS
Heat dissipation from the package can be improved by increasing
the amount of copper attached to the pins of the ADP1762.
However, as shown in Table 8, a point of diminishing returns is
eventually reached, beyond which an increase in the copper size
does not yield significant heat dissipation benefits.
Place the input capacitor as close as possible to the VIN
and GND pins.
Place the output capacitor as close as possible to the
VOUT and GND pins.
Place the soft start capacitor (CSS) as close as possible to the
SS pin.
Place the reference capacitor (CREF) and regulator capacitor
(CREG) as close as possible to the REFCAP pin and the
VREG pin, respectively.
Connect the load as close as possible to the VOUT and
SENSE pins.
12922-045
Use the following recommendations when designing PCBs:
Figure 45. Typical Board Layout, Top Side
12922-046
Use of 0603 or 0805 size capacitors and resistors achieves the
smallest possible footprint solution on boards where area is
limited.
12922-044
Figure 46. Typical Board Layout, Bottom Side
Figure 44. Evaluation Board
Rev. D | Page 17 of 19
ADP1762
Data Sheet
OUTLINE DIMENSIONS
DETAIL A
(JEDEC 95)
0.30
0.23
0.18
0.50
BSC
13
16
12
1
1.75
1.60 SQ
1.45
EXPOSED
PAD
9
0.50
0.40
0.30
TOP VIEW
0.80
0.75
0.70
SIDE VIEW
PKG-005138
4
8
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
P IN 1
IN D I C ATO R AR E A OP T IO N S
(SEE DETAIL A)
5
BOTTOM VIEW
0.20 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WEED-6
08-24-2018-E
PIN 1
INDICATOR
AREA
3.10
3.00 SQ
2.90
Figure 47. 16-Lead Lead Frame Chip Scale Package [LFCSP]
3 mm × 3 mm Body and 0.75 mm Package Height
(CP-16-22)
Dimensions shown in millimeters
ORDERING GUIDE
Model1, 2
ADP1762ACPZ-R7
ADP1762ACPZ-0.9-R7
ADP1762ACPZ0.95-R7
ADP1762ACPZ-1.0-R7
ADP1762ACPZ-1.1-R7
ADP1762ACPZ-1.2-R7
ADP1762ACPZ1.25-R7
ADP1762ACPZ-1.3-R7
ADP1762ACPZ-1.5-R7
ADP1762WACPZ-R7
ADP1762WACPZ-0.9-R7
ADP1762WACPZ0.95-R7
ADP1762WACPZ-1.0-R7
ADP1762WACPZ-1.1-R7
ADP1762WACPZ-1.2-R7
ADP1762WACPZ1.25-R7
ADP1762WACPZ-1.3-R7
ADP1762WACPZ-1.5-R7
ADP1762-1.3-EVALZ
ADP1762-ADJ-EVALZ
Temperature
Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Output
Voltage (V)3
Adjustable
0.9
0.95
1.0
1.1
1.2
1.25
1.3
1.5
Adjustable
0.9
0.95
1.0
1.1
1.2
1.25
1.3
1.5
1.3
1.1
Package Description
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
Evaluation Board
Evaluation Board
1
Package
Option
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
CP-16-22
Marking
Code
LRS
LRT
LUP
LRU
LRV
LRW
LRZ
LRX
LRY
LVH
LV9
LVJ
LVA
LVB
LVD
LVE
LVF
LVG
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications.
3
For additional options, contact a local Analog Devices sales or distribution representative. Additional voltage output options available include the following: 0.5 V,
0.55 V, 0.6 V, 0.65 V, 0.7 V, 0.75 V, 0.8 V, 0.85 V, 1.05 V, 1.15 V, 1.35 V, 1.4 V, or 1.45 V.
2
Rev. D | Page 18 of 19
Data Sheet
ADP1762
AUTOMOTIVE PRODUCTS
The ADP1762W models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
©2016–2021 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12922-3/21(D)
Rev. D | Page 19 of 19
工商网监
湘ICP备2023018690号
