ADP5033ACBZ-12-R7

Dual 3 MHz, 800 mA Buck Regulators with Two 300 mA LDOs ADP5033 Data Sheet FEATURES TYPICAL APPLICATION CIRCUIT ADP5033 BUCK1 ENA ENB MODE MODE BUCK2 Power for processors, ASICS, FPGAs, and RF chipsets Portable instrumentation and medical devices Space constrained devices SW2 C5 10µF EN3 LDO1 (ANALOG) PWM PSM/PWM L2 1µH VOUT2 PGND2 EN2 VIN3 VOUT1 @ 800mA MODE EN2 EN3 EN4 VIN2 C3 1µF VOUT1 PGND1 EN1 C2 4.7µF 1.7V TO 5.5V APPLICATIONS C1 4.7µF ON OFF L1 1µH SW1 VIN1 VOUT3 VOUT2 @ 800mA C6 10µF VOUT3 @ 300mA C7 1µF VIN4 C4 1µF EN4 LDO2 (DIGITAL) VOUT4 VOUT4 @ 300mA C8 1µF AGND 09788-001 2.3V TO 5.5V ACTIV. AND UVLO Main input voltage range: 2.3 V to 5.5 V Two 800 mA buck regulators and two 300 mA LDOs Tiny, 16-ball, 2 mm × 2 mm WLCSP package Regulator accuracy: ±1.8% Factory programmable VOUTx 3 MHz buck operation with forced PWM and auto PWM/PSM modes BUCK1/BUCK2: output voltage range from 0.8 V to 3.8 V LDO1/LDO2: output voltage range from 0.8 V to 5.2 V LDO1/LDO2: low input supply voltage from 1.7 V to 5.5 V LDO1/LDO2: high PSRR and low output noise Figure 1. GENERAL DESCRIPTION The ADP5033 combines two high performance buck regulators and two low dropout regulators (LDO) in a tiny, 16-ball, 2 mm × 2 mm WLCSP to meet demanding performance and board space requirements. The high switching frequency of the buck regulators enables tiny multilayer external components and minimizes the board space. When the MODE pin is set high, the buck regulators operate in forced PWM mode. When the MODE pin is set low, the buck regulators operate in PWM mode when the load current is above a predefined threshold. When the load current falls below a predefined threshold, the regulator operates in power save mode (PSM), improving the light load efficiency. The two bucks operate out of phase to reduce the input capacitor requirement and noise. The low quiescent current, low dropout voltage, and wide input voltage range of the ADP5033 LDO extend the battery life of portable devices. The ADP5033 LDOs maintain power supply rejection greater than 60 dB for frequencies as high as 10 kHz while operating with a low headroom voltage. Rev. H The regulators in the ADP5033 are activated by the ENA and ENB pins. The specific channels controlled by ENA and ENB are set by factory programming. A high voltage level applied to the enable pins activates the regulators. The default output voltages are factory programmable and can be set to a wide range of options. Table 1. Family Models Model ADP5023 ADP5024 ADP5034 Channels 2 Bucks, 1 LDO 2 Bucks, 1 LDO 2 Bucks, 2 LDOs ADP5037 ADP5033 2 Bucks, 2 LDOs 2 Bucks, 2 LDOs with 2 EN pins 1 Buck, 2 LDOs 1 Buck, 2 LDOs with Supervisory, Watchdog, Manual Reset 2 Bucks with 2 ENx pins 2 Bucks, 2 LDOs with precision enable and power-good output ADP5040 ADP5041 ADP5133 ADP5134 Maximum Current 800 mA, 300 mA 1.2 A, 300 mA 1.2 A, 300 mA 800 mA, 300 mA 800 mA, 300 mA Package LFCSP (CP-24-10) LFCSP (CP-24-10) LFCSP (CP-24-10), TSSOP (RE-28-1) LFCSP (CP-24-10) WLCSP (CB-16-8) 1.2 A, 300 mA 1.2 A, 300 mA LFCSP (CP-20-10) LFCSP (CP-20-10) 800 mA 1.2 A, 300 mA WLCSP (CB-16-8) LFCSP (CP-24-10) Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2011–2019 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADP5033 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Theory of Operation ...................................................................... 15 Applications ....................................................................................... 1 Power Management Unit........................................................... 15 Typical Application Circuit ............................................................. 1 BUCK1 and BUCK2 .................................................................. 16 General Description ......................................................................... 1 LDO1 and LDO2 ........................................................................ 17 Revision History ............................................................................... 2 Applications Information .............................................................. 18 Specifications..................................................................................... 3 Buck External Component Selection....................................... 18 General Specifications ................................................................. 3 LDO Capacitor Selection .......................................................... 20 BUCK1 and BUCK2 Specifications ........................................... 4 Power Dissipation and Thermal Considerations ....................... 21 LDO1 and LDO2 Specifications ................................................. 4 Buck Regulator Power Dissipation .......................................... 21 Input and Output Capacitor, Recommended Specifications ........ 5 Junction Temperature ................................................................ 22 Absolute Maximum Ratings ............................................................ 6 PCB Layout Guidelines .................................................................. 23 Thermal Resistance ...................................................................... 6 Typical Application Schematic ..................................................... 24 ESD Caution .................................................................................. 6 Outline Dimensions ....................................................................... 25 Pin Configuration and Function Descriptions ............................. 7 Ordering Guide .......................................................................... 26 Typical Performance Characteristics ............................................. 8 REVISION HISTORY 3/2019—Rev. G to Rev. H Changes to Ordering Guide .......................................................... 26 9/2014—Rev. F to Rev. G Changes to Page Layout ................................................................... 1 Changes to Table 1 ............................................................................ 1 Changes to Ordering Guide .......................................................... 26 10/2013—Rev. E to Rev. F Changes to VIN1 Undervoltage Lockout Parameter, Table 2 ..... 3 Changes to Undervoltage Lockout Section ................................. 16 Moved Ordering Guide.................................................................. 26 Changes to Ordering Guide .......................................................... 26 9/2013—Rev. D to Rev. E Changes to Table 1 ............................................................................ 1 Changes to Ordering Guide .......................................................... 25 5/2013—Rev. C to Rev. D Added Table 1; Renumbered Sequentially .................................... 1 Changes to Ordering Guide .......................................................... 25 1/2013—Rev. B to Rev. C Changes to Figure 9 .......................................................................... 9 Changes to Ordering Guide .......................................................... 25 10/2012—Rev. A to Rev. B Changes to Features Section............................................................ 1 Changes to Buck Output Voltage Accuracy Parameter, Table 2 ....... 4 Changes to LDO Output Voltage Accuracy Parameter, Table 3 ....... 4 Changes to Figure 6 to Figure 8 ...................................................... 8 Changes to Figure 30 to Figure 32 ................................................ 12 Changes to Figure 36 Caption ...................................................... 13 Changes to Undervoltage Lockout Section ................................. 16 Moved Power Dissipation and Thermal Considerations Section .... 21 Changes to Buck Regulator Power Dissipation Section ............ 21 Updated Outline Dimensions ....................................................... 25 Changes to Ordering Guide .......................................................... 25 1/2012—Rev. 0 to Rev. A Changes to Features Section and General Description Section ....1 Changes to Output Characteristics Parameter, Table 2 ................4 Changes to Output Characteristics Parameter, Table 3 and Dropout Voltage Parameter, Table 3 ...............................................4 Changes to Nominal Input and Output Capacitor Ratings Parameter, Table 4 .............................................................................5 Changes to Table 5.............................................................................6 Changed VIN1= VIN2 = VIN3= VIN4 = 5.0 V to VIN1= VIN2 = VIN3= VIN4 = 3.6 V .........................................................................................8 Changes to Figure 4 to Figure 8 .......................................................8 Change to Figure 15 Caption and Figure 17 Caption ................ 10 Changes Figure 19 and Figure 20 ................................................. 10 Changes to Figure 31 and Figure 32 ............................................ 12 Changes to Figure 33, Figure 37, and Figure 38 ......................... 13 Changes to Buck Regulator Power Dissipation Section ............ 15 Changes to LDO Regulator Power Dissipation Section and Junction Temperature Section ...................................................... 16 Changes to Undervoltage Lockout Section ................................. 18 Changes to LDO1 and LDO2 Section ......................................... 19 Changes to Output Capacitor Section ......................................... 20 Changes to Table 9.......................................................................... 21 Change to Input and Output Capacitor Properties Section ..... 22 Changes to Ordering Guide .......................................................... 25 5/2011—Revision 0: Initial Version Rev. H | Page 2 of 28 Data Sheet ADP5033 SPECIFICATIONS GENERAL SPECIFICATIONS VIN1 = VIN2 = VIN3 = VIN4 = 2.3 V to 5.5 V; VIN3 = VIN4 = 1.7 V to 5.5 V; TJ = −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical specifications, unless otherwise noted. Table 2. Parameter INPUT VOLTAGE RANGE THERMAL SHUTDOWN Threshold Hysteresis START-UP TIME 1 BUCK1, LDO1, LDO2 BUCK2 ENA, ENB, MODE INPUTS Input Logic High Input Logic Low Input Leakage Current STANDBY CURRENT All Channels Enabled All Channels Disabled VIN1 UNDERVOLTAGE LOCKOUT Low UVLO Input Voltage Rising Low UVLO Input Voltage Falling 1 Symbol VIN1, VIN2 Test Conditions/Comments TSSD TSSD-HYS TJ rising Min 2.3 tSTART1 tSTART2 VIH VIL VI-LEAKAGE ISTBY-NOSW ISHUTDOWN Typ Max 5.5 150 20 °C °C 250 300 µs µs 1.1 No load, no buck switching TJ = −40°C to +85°C UVLOVIN1RISE UVLOVIN1FALL 1.95 Start-up time is defined as the time from VIN1 > UVLOVIN1RISE to VOUT1, VOUT2, VOUT3, and VOUT4 reaching 90% of their nominal levels. Rev. H | Page 3 of 28 Unit V 0.05 0.4 1 V V µA 108 0.3 175 1 µA µA 2.275 V V ADP5033 Data Sheet BUCK1 AND BUCK2 SPECIFICATIONS VIN1 = VIN2 = 2.3 V to 5.5 V; TJ = −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical specifications, unless otherwise noted. 1 Table 3. Parameter INPUT CHARACTERISTICS Input Voltage Range OUTPUT CHARACTERISTICS Output Voltage Accuracy Line Regulation Load Regulation PSM CURRENT THRESHOLD PSM to PWM Operation OPERATING SUPPLY CURRENT BUCK1 Only Test Conditions/Comments Min VIN1, VIN2 PWM mode, ILOAD1 = ILOAD2 = 0 mA to 800 mA 2.3 ∆VOUT1/VOUT1, ∆VOUT2/VOUT2 (∆VOUT1/VOUT1)/∆VIN1, (∆VOUT2/VOUT2)/∆VIN2 (∆VOUT1/VOUT1)/∆IOUT1, (∆VOUT2/VOUT2)/∆IOUT2 PWM mode; ILOAD1 = ILOAD2 = 0 mA PWM mode −1.8 IIN IIN BUCK1 and BUCK2 IIN Current Limit ACTIVE PULL-DOWN OSCILLATOR FREQUENCY ILOAD = 0 mA to 800 mA, PWM mode IPSM BUCK2 Only SW CHARACTERISTICS SW On Resistance 1 Symbol RPFET RPFET RNFET RNFET ILIMIT1, ILIMIT2 RPDWN-B fSW MODE = ground ILOAD1 = 0 mA, device not switching, all other channels disabled ILOAD2 = 0 mA, device not switching, all other channels disabled ILOAD1 = ILOAD2 = 0 mA, device not switching, LDO channels disabled PFET at VIN1 = 5 V PFET at VIN1 = 3.6 V NFET at VIN1 = 5 V NFET at VIN1 = 3.6 V PFET switch peak current limit Channel disabled 1100 2.5 Typ Max Unit 5.5 V +1.8 −0.05 % %/V −0.1 %/A 100 mA 44 μA 55 μA 67 μA 145 180 110 125 1350 75 3.0 235 295 190 220 3.5 mΩ mΩ mΩ mΩ mA Ω MHz All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC). LDO1 AND LDO2 SPECIFICATIONS VIN3 = (VOUT3 + 0.5 V) or 1.7 V (whichever is greater) to 5.5 V, VIN4 = (VOUT4 + 0.5 V) or 1.7 V (whichever is greater) to 5.5 V; CIN = COUT = 1 µF; TJ = −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical specifications, unless otherwise noted. 1 Table 4. Parameter INPUT VOLTAGE RANGE OPERATING SUPPLY CURRENT Bias Current per LDO 2 Total System Input Current LDO1 or LDO2 Only LDO1 and LDO2 Only OUTPUT CHARACTERISTICS Output Voltage Accuracy Line Regulation Load Regulation 3 Symbol VIN3, VIN4 Test Conditions/Comments IVIN3BIAS/IVIN4BIAS IOUT3 = IOUT4 = 0 µA IOUT3 = IOUT4 = 10 mA IOUT3 = IOUT4 = 300 mA Includes all current into VIN1, VIN2, VIN3, and VIN4 IOUT3 = IOUT4 = 0 µA, all other channels disabled IOUT3 = IOUT4 = 0 µA, buck channels disabled IIN ∆VOUT3/VOUT3, ∆VOUT4/VOUT4 (∆VOUT3/VOUT3)/∆VIN3, (∆VOUT4/VOUT4)/∆VIN4 (∆VOUT3/VOUT3)/∆IOUT3, (∆VOUT4/VOUT4)/∆IOUT4 Min 1.7 Typ Max 5.5 Unit V 10 60 165 30 100 245 µA µA µA 53 74 µA µA 100 µA < IOUT3 < 300 mA, 100 µA < IOUT4 < 300 mA −1.8 +1.8 % IOUT3 = IOUT4 = 1 mA −0.03 +0.03 %/V 0.003 %/mA IOUT3 = IOUT4 = 1 mA to 300 mA Rev. H | Page 4 of 28 0.001 Data Sheet Parameter DROPOUT VOLTAGE 4 CURRENT-LIMIT THRESHOLD 5 ACTIVE PULL-DOWN POWER SUPPLY REJECTION RATIO Regulator LDO1 ADP5033 Symbol VDROPOUT ILIMIT3, ILIMIT4 RPDWN-L PSRR Regulator LDO2 Test Conditions/Comments VOUT3 = VOUT4 = 5.2 V, IOUT3 = IOUT4 = 300 mA VOUT3 = VOUT4 = 3.3 V, IOUT3 = IOUT4 = 300 mA VOUT3 = VOUT4 = 2.5 V, IOUT3 = IOUT4 = 300 mA VOUT3 = VOUT4 = 1.8 V, IOUT3 = IOUT4 = 300 mA Min Channel disabled Typ 50 65 85 165 600 600 10 kHz, VIN3 = 3.3 V, VOUT3 = 2.8 V, IOUT3 = 1 mA 100 kHz, VIN3 = 3.3 V, VOUT3 = 2.8 V, IOUT3 = 1 mA 1 MHz, VIN3 = 3.3 V, VOUT3 = 2.8 V, IOUT3 = 1 mA 10 kHz, VIN4 = 1.8 V, VOUT4 = 1.2 V, IOUT4 = 1 mA 100 kHz, VIN4 = 1.8 V, VOUT4 = 1.2 V, IOUT4 = 1 mA 1 MHz, VIN4 = 1.8 V, VOUT4 = 1.2 V, IOUT4 = 1 mA 60 62 63 54 57 64 335 Max Unit mV mV mV mV mA Ω 110 dB dB dB dB dB dB All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC). This is the input current into VIN3/VIN4, which is not delivered to the output load. 3 Based on an endpoint calculation using 1 mA and 300 mA loads. 4 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only to output voltages above 1.7 V. 5 Current-limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.0 V output voltage is defined as the current that causes the output voltage to drop to 90% of 3.0 V, or 2.7 V. 1 2 INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS TA = −40°C to +125°C, unless otherwise specified. Table 5. Parameter NOMINAL INPUT AND OUTPUT CAPACITOR RATINGS BUCK1, BUCK2 Input Capacitor Rating BUCK1, BUCK2 Output Capacitor Rating LDO1, LDO2 1 Input and Output Capacitor Rating CAPACITOR ESR 1 Symbol Min CMIN1, CMIN2 CMIN1, CMIN2 CMIN3, CMIN4 RESR 4.7 10 1.0 0.001 Typ Max Unit 40 40 µF µF µF Ω 1 The minimum input and output capacitance should be greater than 0.70 µF over the full range of operating conditions. The full range of operating conditions in the application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R- and X5R-type capacitors are recommended; Y5V and Z5U capacitors are not recommended for use because of their poor temperature and dc bias characteristics. Rev. H | Page 5 of 28 ADP5033 Data Sheet ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 6. Parameter VIN1 to AGND VIN2 to VIN1 PGND1, PGND2 to AGND VIN3, VIN4, VOUT1, VOUT2, ENA, ENB, MODE to AGND VOUT3 to AGND VOUT4 to AGND SW1 to PGND1 SW2 to PGND2 Storage Temperature Range Operating Junction Temperature Range Soldering Conditions θJA and ΨJB are specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Rating −0.3 V to +6 V −0.3 V to +0.3 V −0.3 V to +0.3 V −0.3 V to (VIN1 + 0.3 V) −0.3 V to (VIN3 + 0.3 V) −0.3 V to (VIN4 + 0.3 V) −0.3 V to (VIN1 + 0.3 V) −0.3 V to (VIN2 + 0.3 V) −65°C to +150°C −40°C to +125°C JEDEC J-STD-020 Table 7. Thermal Resistance Package Type 16-Ball, 0.5 mm Pitch WLCSP ESD CAUTION Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. For detailed information on power dissipation, see the Power Dissipation and Thermal Considerations section. Rev. H | Page 6 of 28 θJA 57 ΨJB 14 Unit °C/W Data Sheet ADP5033 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS BALL A1 INDICATOR 2 1 3 4 VOUT3 VIN3 VIN4 VOUT4 AGND MODE ENA A ENB B VIN1 VOUT1 VOUT2 VIN2 C PGND1 SW1 SW2 PGND2 TOP VIEW (BALL SIDE DOWN) Not to Scale 09788-002 D Figure 2. Pin Configuration—View from the Top of the Die Table 8. Pin Function Descriptions Pin No. A1 A2 A3 A3 B1 B2 B3 B4 C1 C2 C3 C4 D1 D2 D3 D4 Mnemonic VOUT3 VIN3 VIN4 VOUT4 AGND MODE ENA ENB VIN1 VOUT1 VOUT2 VIN2 PGND1 SW1 SW2 PGND2 Description LDO1 Output Voltage and Sensing Input. LDO1 Input Supply (1.7 V to 5.5 V, VIN4 ≤ VIN1 = VIN2). LDO2 Input Supply (1.7 V to 5.5 V, VIN3 ≤ VIN1 = VIN2). LDO2 Output Voltage and Sensing Input. Analog Ground. BUCK1/BUCK2 Operating Mode. MODE = high: forced PWM operation. MODE = low: auto PWM/PSM operation. Regulator Enable Pin A, Active High. The regulators turned on with ENA are factory programmed. Regulator Enable Pin B, Active High. The regulators turned on with ENB are factory programmed. BUCK1 Input Supply (2.3 V to 5.5 V) and UVLO Detection. Connect VIN1 to VIN2. BUCK1 Output Voltage Sensing Input. BUCK2 Output Voltage Sensing Input. BUCK2 Input Supply (2.3 V to 5.5 V). Connect VIN2 to VIN1. Dedicated Power Ground for BUCK1. BUCK1 Switching Node. BUCK2 Switching Node. Dedicated Power Ground for BUCK2. Rev. H | Page 7 of 28 ADP5033 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS VIN1= VIN2 = VIN3= VIN4 = 3.6 V, TA = 25°C, unless otherwise noted. 3.310 140 3.305 –40°C 3.300 100 +25°C VOUT (V) 3.295 80 3.290 60 3.285 40 3.280 20 3.275 2.8 3.3 3.8 4.3 4.8 09788-139 3.270 0 2.3 5.3 INPUT VOLTAGE (V) +85°C 0 0.1 0.2 0.3 0.4 IOUT (A) 0.5 0.6 0.7 0.8 09788-225 QUIESCENT CURRENT (µA) 120 Figure 6. BUCK1 Load Regulation Across Temperature, VIN = 4.2 V, VOUT1 = 3.3 V, PWM Mode Figure 3. System Quiescent Current vs. Input Voltage, VOUT1 = 3.3 V, VOUT2 = 1.8 V, VOUT3 = 1.2 V, VOUT4 = 3.3 V, All Channels Unloaded 1.812 T 1.810 SW –40°C 4 1.808 VOUT (V) IOUT 2 VOUT 1 EN +25°C 1.806 1.804 1.802 +85°C BW BW CH2 50.0mA Ω BW M 40.0µs BW CH4 5.00V T 11.20% A CH3 2.2V 1.798 09788-249 CH1 2.00V CH3 5.00V 0 0.1 0.2 0.4 IOUT (A) 0.5 0.6 0.7 0.8 Figure 7. BUCK2 Load Regulation Across Temperature, VIN = 3.6 V, VOUT2 = 1.8 V, PWM Mode Figure 4. Buck1 Startup, VOUT1 = 1.8 V, IOUT1 = 5 mA 0.808 T 0.807 SW 4 +25°C 0.806 VOUT (V) IOUT 2 1 0.3 09788-224 1.800 3 VOUT –40°C 0.805 +85°C 0.804 EN 0.803 BW BW CH2 50.0mA Ω BW M 40.0µs BW CH4 5.00V T 11.20% A CH3 2.2V 0.802 09788-248 CH1 2.00V CH3 5.00V 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 IOUT (A) Figure 8. BUCK1 Load Regulation Across Temperature, VIN = 3.6 V, VOUT1 = 0.8 V, PWM Mode Figure 5. BUCK2 Startup, VOUT2 = 3.3 V, IOUT2 = 10 mA Rev. H | Page 8 of 28 09788-226 3 ADP5033 100 100 90 90 80 80 70 70 EFFICIENCY (%) 60 50 40 40 VIN = 3.9V VIN = 4.2V VIN = 5.5V 0 10 100 1000 ILOAD (mA) 0 0.001 1 Figure 12. BUCK2 Efficiency vs. Load Current, Across Input Voltage, VOUT2 = 1.8 V, PWM Mode 100 90 90 80 80 70 70 EFFICIENCY (%) 100 60 50 40 60 50 40 30 30 VIN = 2.3V VIN = 3.6V VIN = 4.2V VIN = 5.5V 20 20 VIN = 3.9V 10 10 VIN = 4.2V VIN = 5.5V 0.1 1 0 0.001 09788-039 0.01 IOUT (A) 0.01 0.1 1 IOUT (A) Figure 13. BUCK1 Efficiency vs. Load Current, Across Input Voltage, VOUT1 = 0.8 V, Auto Mode Figure 10. BUCK1 Efficiency vs. Load Current, Across Input Voltage, VOUT1 = 3.3 V, PWM Mode 100 90 90 80 80 70 70 EFFICIENCY (%) 100 60 50 40 60 50 40 30 30 0.01 0.1 IOUT (A) 10 1 0 0.001 09788-036 10 VIN = 2.3V VIN = 3.6V VIN = 4.2V VIN = 5.5V 20 VIN = 2.3V VIN = 3.6V VIN = 4.2V VIN = 5.5V 20 0 0.001 0.1 IOUT (A) Figure 9. BUCK1 Efficiency vs. Load Current, Across Input Voltage, VOUT1 = 3.3 V, Auto Mode 0 0.001 0.01 09788-034 1 09788-038 10 10 09788-035 VIN = 2.4V VIN = 3.6V VIN = 4.5V VIN = 5.5V 20 20 EFFICIENCY (%) 50 30 30 EFFICIENCY (%) 60 0.01 0.1 IOUT (A) 1 09788-065 EFFICIENCY (%) Data Sheet Figure 14. BUCK1 Efficiency vs. Load Current, Across Input Voltage, VOUT1 = 0.8 V, PWM Mode Figure 11. BUCK2 Efficiency vs. Load Current, Across Input Voltage, VOUT2 = 1.8 V, Auto Mode Rev. H | Page 9 of 28 ADP5033 Data Sheet 100 3.3 90 3.2 80 3.1 FREQUENCY (MHz) EFFICIENCY (%) 70 60 50 40 30 3.0 2.9 2.8 2.7 20 IOUT (A) 2.5 0 0.2 0.4 0.6 IOUT (A) 0.8 1.0 1.2 09788-040 1 0.1 0.01 09788-062 0 0.001 TA = +25°C TA = –40°C TA = +85°C 2.6 +25°C +85°C –40°C 10 Figure 18. BUCK2 Switching Frequency vs. Output Current, Across Temperature, VOUT2 = 1.8 V, PWM Mode Figure 15. BUCK1 Efficiency vs. Load Current, Across Temperature, VIN1 = 3.9 V, VOUT1 = 3.3 V, Auto Mode 100 T VOUT 90 80 1 EFFICIENCY (%) 70 ISW 60 2 50 40 SW 30 20 +85°C +25°C –40°C 0.01 0.1 4 1 IOUT (A) Figure 16. BUCK2 Efficiency vs. Load Current, Across Temperature, VOUT2 = 1.8 V, Auto Mode CH2 500mA Ω CH4 2.00V CH1 50.0mV M 4.00µs A CH2 240mA T 28.40% 09788-251 0 0.001 09788-063 10 Figure 19. Typical Waveforms, VOUT1 = 3.3 V, IOUT1 = 30 mA, Auto Mode 100 T 90 VOUT 80 1 EFFICIENCY (%) 70 60 ISW 2 50 40 SW 30 20 +85°C +25°C –40°C 0.01 0.1 IOUT (A) 4 1 CH1 50.0mV Figure 17. BUCK1 Efficiency vs. Load Current, Across Temperature, VOUT1 = 0.8 V, Auto Mode BW CH2 500mA Ω M 4.00µs A CH2 BW CH4 2.00V T 28.40% 220mA 09788-250 0 0.001 09788-200 10 Figure 20. Typical Waveforms, VOUT2 = 1.8 V, IOUT2 = 30 mA, Auto Mode Rev. H | Page 10 of 28 Data Sheet ADP5033 T T VOUT 1 VIN ISW VOUT 2 1 SW SW 4 3 M 400ns A CH2 220mA T 28.40% CH1 50.0mV CH3 1.00V 09788-027 CH2 500mA Ω CH4 2.00V CH1 50mV Figure 21. Typical Waveforms, VOUT1 = 3.3 V, IOUT1 = 30 mA, PWM Mode CH4 2.00V M 1.00ms A CH3 4.80V T 30.40% 09788-013 4 Figure 24. BUCK2 Response to Line Transient, VIN = 4.5 V to 5.0 V, VOUT2 = 1.8 V, PWM Mode T T SW VOUT 1 4 ISW 2 VOUT 1 SW IOUT 4 CH2 500mA Ω CH4 2.00V M 400ns A CH2 220mA T 28.40% CH1 50.0mV Figure 22. Typical Waveforms, VOUT2 = 1.8 V, IOUT2 = 30 mA, PWM Mode CH2 50.0mA Ω CH4 5.00V M 20.0µs A CH2 T 60.000µs 356mA 09788-016 CH1 50mV 09788-026 2 Figure 25. BUCK1 Response to Load Transient, IOUT1 from 1 mA to 50 mA, VOUT1 = 3.3 V, Auto Mode T T SW 4 VIN VOUT VOUT 1 1 SW IOUT 3 CH4 2.00V M 1.00ms T 30.40% A CH3 4.80V CH1 50.0mV 09788-012 CH1 50.0mV CH3 1.00V Figure 23. Buck1 Response to Line Transient, Input Voltage from 4.5 V to 5.0 V, VOUT1 = 3.3 V, PWM Mode CH2 50.0mA Ω CH4 5.00V M 20.0µs A CH2 T 22.20% 379mA 09788-015 2 Figure 26. BUCK2 Response to Load Transient, IOUT2 from 1 mA to 50 mA, VOUT2 = 1.8 V, Auto Mode Rev. H | Page 11 of 28 ADP5033 Data Sheet T SW EN 4 2 VOUT 1 VOUT 3 2 IIN CH1 50.0mV CH2 200mA Ω CH4 5.00V M 20.0µs A CH2 408mA T 20.40% 09788-017 1 CH1 100mA CH3 1.00V Figure 27. BUCK1 Response to Load Transient, IOUT1 from 20 mA to 180 mA, VOUT1 = 3.3 V, Auto Mode M 40.0µs CH2 5.00V A CH2 T 159.400µs 4.20V 09788-022 IOUT Figure 30. LDO Startup, VOUT3 = 1.8 V 3.304 T 3.303 SW 3.302 4 VIN = 5.5V 3.301 3.300 VOUT (V) VOUT 1 VIN = 4.2V 3.299 VIN = 3.8V 3.298 3.297 IOUT 3.296 2 CH2 200mA Ω CH4 5.00V M 20.0µs A CH2 88.0mA T 19.20% 3.294 09788-018 CH1 100mV 0 0.1 0.3 Figure 31. LDO Load Regulation Across Input Voltage, VOUT3 = 3.3 V Figure 28. BUCK2 Response to Load Transient, IOUT2 from 20 mA to 180 mA, VOUT2 = 1.8 V, Auto Mode 1.802 T 1.801 VOUT2 –40°C 1.800 2 1.799 VOUT (V) SW1 3 VOUT1 1 0.2 IOUT (A) 09788-232 3.295 1.798 1.797 +25°C 1.796 1.795 SW2 1.794 CH2 5.00V CH4 5.00V M 400ns T 50.00% A CH4 1.90V 1.792 09788-066 CH1 5.00V CH3 5.00V 0 0.1 0.2 IOUT (A) Figure 29. VOUT and SW Waveforms for BUCK1 and BUCK2 in PWM Mode Showing Out-of-Phase Operation 0.3 09788-233 +85°C 1.793 4 Figure 32. LDO Load Regulation Across Temperature, VIN3 = 3.6 V, VOUT3 = 1.8 V Rev. H | Page 12 of 28 Data Sheet 3.0 IOUT = 10mA IOUT = 100µA T IOUT = 1mA IOUT = 100mA IOUT = 150mA IOUT = 300mA 2.5 2.0 VOUT (V) ADP5033 VIN 1.5 VOUT 2 1 1.0 0.5 VIN (V) CH1 20.0mV CH3 1.00V 09788-234 0 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 M 100µs T 28.40% 4.80V Figure 36. LDO Response to Line Transient, Input Voltage from 4.5 V to 5 V, VOUT3 = 2.8 V Figure 33. LDO Line Regulation Across Output Load, VOUT3 = 2.8 V 60 50 VIN = 5V 45 55 VIN = 3.3V 40 GROUND CURRENT (µA) A CH3 09788-014 3 50 RMS NOISE (µV) 35 30 25 20 15 45 40 35 10 0 0.05 0.10 0.15 0.20 25 0.001 09788-136 0 0.25 LOAD CURRENT (A) Figure 34. LDO Ground Current vs. Output Load, VIN3 = 3.3 V, VOUT3 = 2.8 V 0.01 1 ILOAD (mA) 10 100 Figure 37. LDO Output Noise vs. Load Current, Across Input Voltage, VOUT3 = 2.8 V 65 T VIN = 5V 60 IOUT VIN = 3.3V RMS NOISE (µV) 55 2 1 0.1 09788-255 30 5 VOUT 50 45 40 35 CH2 100mA Ω M 40.0µs A CH2 T 19.20% 52.0mA 25 0.001 09788-019 CH1 100mV Figure 35. LDO Response to Load Transient, IOUT3 from 1 mA to 80 mA, VOUT3 = 2.8 V 0.01 0.1 1 ILOAD (mA) 10 100 09788-256 30 Figure 38. LDO Output Noise vs. Load Current, Across Input Voltage, VOUT3 = 3.0 V Rev. H | Page 13 of 28 ADP5033 Data Sheet 0 0 –10 –20 –20 –40 –40 PSRR (dB) PSRR (dB) –30 100µA 1mA 10mA 50mA 100mA 150mA –50 –60 100µA 1mA 10mA 50mA 100mA 150mA –60 –80 –70 –80 –100 100 1k 10k 100k FREQUENCY (Hz) 1M 10M –120 10 09788-050 Figure 39. LDO PSRR Across Output Load, VIN3 = 3.3 V, VOUT3 = 2.8 V 10k 100k FREQUENCY (Hz) 1M 10M 0 –10 –20 –20 –30 PSRR (dB) –40 –60 –80 –100 100 1k 10k 100k FREQUENCY (Hz) 100µA 1mA 10mA 50mA 100mA 150mA –40 –50 –60 –70 100µA 1mA 10mA 50mA 100mA 150mA –80 –90 1M 10M 09788-051 PSRR (dB) 1k Figure 41. LDO PSRR Across Output Load, VIN3 = 5.0 V, VOUT3 = 2.8 V 0 –120 10 100 Figure 40. LDO PSRR Across Output Load, VIN3 = 3.3 V, VOUT3 = 3.0 V –100 10 100 1k 10k 100k FREQUENCY (Hz) 1M 10M Figure 42. LDO PSRR Across Output Load, VIN3 = 5.0 V, VOUT3 = 3.0 V Rev. H | Page 14 of 28 09788-052 –100 10 09788-053 –90 Data Sheet ADP5033 THEORY OF OPERATION VOUT1 GM ERROR AMP VDDA ENBK1 VOUT2 75Ω 75Ω ENBK2 ADP5033 GM ERROR AMP PWM COMP PWM COMP VIN2 SOFT START SOFT START VIN1 ILIMIT ILIMIT PSM COMP PSM COMP LOW CURRENT PWM/ PSM CONTROL BUCK2 PWM/ PSM CONTROL BUCK1 LOW CURRENT SW2 SW1 DRIVER AND ANTISHOOT THROUGH OSCILLATOR DRIVER AND ANTISHOOT THROUGH SYSTEM UNDERVOLTAGE LOCKOUT OPMODE SEL B THERMAL SHUTDOWN PGND1 PGND2 MODE2 Y ENLDO1 600Ω A MODE LDO UNDERVOLTAGE LOCK OUT ENBK1 ENABLE AND MODE CONTROL ENB R1 ENBK2 ENLDO1 ENLDO2 R3 LDO CONTROL VDDA VDDA 600Ω R2 VIN3 AGND VOUT3 VIN4 LDO CONTROL ENLDO1 R4 VOUT4 09788-003 ENA LDO UNDERVOLTAGE LOCK OUT Figure 43. Functional Block Diagram POWER MANAGEMENT UNIT The ADP5033 is a micropower management unit (µPMU) combing two step-down (buck) dc-to-dc convertors and two low dropout linear regulators (LDO). The high switching frequency and tiny 16-ball WLCSP package allow for a small power management solution. To combine these high performance regulators into the µPMU, there is a system controller allowing them to operate together. The buck regulators can operate in forced PWM mode if the MODE pin is at a logic high level. In forced PWM mode, the buck switching frequency is always constant and does not change with the load current. If the MODE pin is at logic low, the switching regulators operate in auto PWM/PSM mode. In this mode, the regulators operate at fixed PWM frequency when the load current is above the power saving current threshold. When the load current falls below the power save current threshold, the regulator in question enters PSM where the switching occurs in bursts. The burst repetition is a function of the current load and the output capacitor value. This operating mode reduces the switching and quiescent current losses. The auto PWM/PSM mode transition is controlled independently for each buck regulator. The two bucks operate synchronized to each other. When a regulator is turned on, the output voltage ramp is controlled through a soft start circuit to avoid a large inrush current due to the charging of the output capacitors. Thermal Protection In the event that the junction temperature rises above 150°C, the thermal shutdown circuit turns off all the regulators. Extreme junction temperatures can be the result of high current operation, poor circuit board design, or high ambient temperature. A 20°C hysteresis is included so that when thermal shutdown occurs, the regulators do not return to operation until the on-chip temperature drops below 130°C. When coming out of thermal shutdown, all regulators restart with soft start control. Rev. H | Page 15 of 28 ADP5033 Data Sheet Undervoltage Lockout To protect against battery discharge, undervoltage lockout (UVLO) circuitry is integrated in the system. If the input voltage on VIN1 drops below a typical 2.15 V UVLO threshold, all channels shut down. In the buck channels, both the power switch and the synchronous rectifier turn off. When the voltage on VIN1 rises above the UVLO threshold, the part is enabled once more. Alternatively, the user can request a new device model with a UVLO set at a higher level, suitable for 5 V supply applications. For these models, the device reaches the turn-off threshold when the input supply drops to 3.65 V typical. To order a device with options other than the default options listed in the Ordering Guide section, contact your local Analog Devices, Inc., sales or distribution representative. In case of a thermal or UVLO event, the active pull-down resistors (if factory enabled) are enabled to discharge the output capacitors quickly. The pull-down resistors remain engaged until the thermal fault event is no longer present or the input supply voltage falls below the VPOR voltage level. The typical value of VPOR is approximately 1 V. Enable/Shutdown The ADP5033 has two enable pins (ENA and ENB). A high level applied to the enable pins enables a certain selection of regulators defined by factory programming. For example, the ADP5033 can be factory programmed to enable BUCK1 and LDO2 with ENA and BUCK2 and LDO1 with ENB. When both enables are low, all regulators are turned off. When both enable pins are high, all regulators are turned on. All possible regulator combinations can be factory programmed to operate with the ENA and ENB pins. Figure 44 shows the regulator activation timings for the ADP5033 when both enables are connected to VINx. Figure 44 also shows the active pull-down activation. BUCK1 AND BUCK2 The two bucks use a fixed frequency and high speed current mode architecture. The bucks operate with an input voltage of 2.3 V to 5.5 V. Control Scheme The bucks operate with a fixed frequency, current mode PWM control architecture at medium to high loads for high efficiency but shift to a PSM control scheme at light loads to lower the regulation power losses. When operating in fixed frequency PWM mode, the duty cycle of the integrated switches is adjusted and regulates the output voltage. When operating in PSM at light loads, the output voltage is controlled in a hysteretic manner, with higher output voltage ripple. During part of this time, the converter is able to stop switching and enters an idle mode, which improves conversion efficiency. PWM Mode In PWM mode, the bucks operate at a fixed frequency of 3 MHz set by an internal oscillator. At the start of each oscillator cycle, the PFET switch is turned on, sending a positive voltage across the inductor. Current in the inductor increases until the current sense signal crosses the peak inductor current threshold that turns off the PFET switch and turns on the NFET synchronous rectifier. This sends a negative voltage across the inductor, causing the inductor current to decrease. The synchronous rectifier stays on for the rest of the cycle. The buck regulates the output voltage by adjusting the peak inductor current threshold. VIN1 VUVLO VPOR VOUT1 VOUT3 VOUT4 30µs (MIN) VOUT2 30µs (MIN) 50µs (MIN) 50µs (MIN) BUCK1, LDO1, LDO2 PULL-DOWNS 09788-148 BUCK2 PULL-DOWN Figure 44. Regulators Sequencing on the ADP5033 (ENx = VINx) Rev. H | Page 16 of 28 Data Sheet ADP5033 PSM Current Limit The bucks smoothly transition to PSM operation when the load current decreases below the PSM current threshold. When either of the bucks enters PSM, an offset is induced in the PWM regulation level, which makes the output voltage rise. When the output voltage reaches a level approximately 1.5% above the PWM regulation level, PWM operation is turned off. At this point, both power switches are off, and the buck enters an idle mode. The output capacitor discharges until the output voltage falls to the PWM regulation voltage, at which point the device drives the inductor to make the output voltage rise again to the upper threshold. This process is repeated while the load current is below the PSM current threshold. Each buck has protection circuitry to limit the amount of positive current flowing through the PFET switch and the amount of negative current flowing through the synchronous rectifier. The positive current limit on the power switch limits the amount of current that can flow from the input to the output. The negative current limit prevents the inductor current from reversing direction and flowing out of the load. 100% Duty Operation The ADP5033 has a dedicated MODE pin controlling the PSM and PWM operation. A high logic level applied to the MODE pin forces both bucks to operate in PWM mode. A logic level low sets the bucks to operate in auto PSM/PWM. With a dropin input voltage or with an increase in load current, the buck may reach a limit where, even with the PFET switch on 100% of the time, the output voltage drops below the desired output voltage. At this limit, the buck transitions to a mode where the PFET switch stays on 100% of the time. When the input conditions change again and the required duty cycle falls, the buck immediately restarts PWM regulation without allowing overshoot on the output voltage. PSM Current Threshold Active Pull-Downs The PSM current threshold is set to 100 mA. The bucks employ a scheme that enables this current to remain accurately controlled, independent of input and output voltage levels. This scheme also ensures that there is very little hysteresis between the PSM current threshold for entry to and exit from the PSM. The PSM current threshold is optimized for excellent efficiency over all load currents. All regulators have optional, factory programmable, active pulldown resistors discharging the respective output capacitors when the regulators are disabled by the ENx pins or by a faulty condition. The pull-down resistors are connected between VOUTx and AGND. Active pull-downs are disabled when the regulators are turned on. The typical value of the pull-down resistor is 600 Ω for the LDOs and 75 Ω for the bucks. Figure 44 shows the activation timings for the active pull-down during regulator activation and deactivation. Oscillator/Phasing of Inductor Switching The ADP5033 ensures that both bucks operate at the same switching frequency when both bucks are in PWM mode. LDO1 AND LDO2 Additionally, the ADP5033 ensures that when both bucks are in PWM mode, they operate out of phase, whereby the BUCK2 PFET starts conducting exactly half a clock period after the BUCK1 PFET starts conducting. The ADP5033 contains two LDOs with low quiescent current and low dropout voltage, and provides up to 300 mA of output current. Drawing a low 25 μA quiescent current (typical) at no load makes the LDO ideal for battery-operated portable equipment. Short-Circuit Protection Each LDO operates with an input voltage of 1.7 V to 5.5 V. The wide operating range makes these LDOs suitable for cascading configurations where the LDO supply voltage is provided from one of the buck regulators. The bucks include frequency foldback to prevent output current runaway on a hard short. When the voltage at the feedback pin falls below half the target output voltage, indicating the possibility of a hard short at the output, the switching frequency is reduced to half the internal oscillator frequency. The reduction in the switching frequency allows more time for the inductor to discharge, preventing a runaway of output current. Soft Start The bucks have an internal soft start function that ramps the output voltage in a controlled manner upon startup, thereby limiting the inrush current. This prevents possible input voltage drops when a battery or a high impedance power source is connected to the input of the converter. Each LDO also provides high power supply rejection ratio (PSRR), low output noise, and excellent line and load transient response with just a small 1 µF ceramic input and output capacitor. LDO1 is optimized to supply analog circuits because it offers better noise performance compared to LDO2. LDO1 should be used in applications where noise performance is critical. Rev. H | Page 17 of 28 ADP5033 Data Sheet APPLICATIONS INFORMATION BUCK EXTERNAL COMPONENT SELECTION Output Capacitor Trade-offs between performance parameters such as efficiency and transient response can be made by varying the choice of external components in the applications circuit, as shown in Figure 1. Higher output capacitor values reduce the output voltage ripple and improve load transient response. When choosing this value, it is also important to account for the loss of capacitance due to output voltage dc bias. Inductor Ceramic capacitors are manufactured with a variety of dielectrics, each with a different behavior over temperature and applied voltage. Capacitors must have a dielectric adequate to ensure the minimum capacitance over the necessary temperature range and dc bias conditions. X5R or X7R dielectrics with a voltage rating of 6.3 V or 10 V are recommended for best performance. Y5V and Z5U dielectrics are not recommended for use with any dc-to-dc converter because of their poor temperature and dc bias characteristics. The high switching frequency of the ADP5033 bucks allows for the selection of small chip inductors. For best performance, use inductor values between 0.7 μH and 3 μH. Suggested inductors are shown in Table 9. The peak-to-peak inductor current ripple is calculated using the following equation: VOUT × (VIN − VOUT ) VIN × f SW × L The worst-case capacitance accounting for capacitor variation over temperature, component tolerance, and voltage is calculated using the following equation: where: fSW is the switching frequency. L is the inductor value. CEFF = COUT × (1 − TEMPCO) × (1 − TOL) The minimum dc current rating of the inductor must be greater than the inductor peak current. The inductor peak current is calculated using the following equation: I PEAK = I LOAD( MAX ) + I RIPPLE 2 Inductor conduction losses are caused by the flow of current through the inductor, which has an associated internal dc resistance (DCR). Larger sized inductors have smaller DCR, which may decrease inductor conduction losses. Inductor core losses are related to the magnetic permeability of the core material. Because the bucks are high switching frequency dc-to-dc converters, shielded ferrite core material is recommended for its low core losses and low EMI. where: CEFF is the effective capacitance at the operating voltage. TEMPCO is the worst-case capacitor temperature coefficient. TOL is the worst-case component tolerance. In this example, the worst-case temperature coefficient (TEMPCO) over −40°C to +85°C is assumed to be 15% for an X5R dielectric. The tolerance of the capacitor (TOL) is assumed to be 10%, and COUT is 9.2 μF at 1.8 V, as shown in Figure 45. Substituting these values in the equation yields CEFF = 9.2 μF × (1 − 0.15) × (1 − 0.1) ≈ 7.0 μF To guarantee the performance of the bucks, it is imperative that the effects of dc bias, temperature, and tolerances on the behavior of the capacitors be evaluated for each application. Table 9. Suggested 1.0 μH Inductors Model LQM2MPN1R0NG0B LQM18FN1R0M00B BRC1608T1R0M Dimensions (mm) 2.0 × 1.6 × 0.9 1.6 × 0.8 × 0.8 1.6 × 0.8 × 0.8 ISAT (mA) 1400 150 520 DCR (mΩ) 85 26 180 EPL2014-102ML GLFR1608T1R0M-LR 0603LS-102 MDT2520-CN 2.0 × 2.0 × 1.4 1.6 × 0.8 × 0.8 1.8 × 1.69 × 1.1 2.5 × 2.0 × 1.2 900 230 400 1350 59 80 81 85 10 CAPACITANCE (µF) Vendor Murata Murata Taiyo Yuden Coilcraft TDK Coilcraft Toko 12 8 6 4 2 0 0 1 2 3 4 5 DC BIAS VOLTAGE (V) Figure 45. Typical Capacitor Performance Rev. H | Page 18 of 28 6 09788-004 I RIPPLE = Data Sheet ADP5033 The peak-to-peak output voltage ripple for the selected output capacitor and inductor values is calculated using the following equation: VRIPPLE = I RIPPLE VIN ≈ 8 × f SW × COUT (2π × f SW )2 × L × COUT Capacitors with lower equivalent series resistance (ESR) are preferred to guarantee low output voltage ripple, as shown in the following equation: ESRCOUT ≤ VRIPPLE I RIPPLE The effective capacitance needed for stability, which includes temperature and dc bias effects, is a minimum of 7 µF and a maximum of 40 µF. The buck regulators require 10 µF output capacitors to guarantee stability and response to rapid load variations and to transition into and out of the PWM/PSM modes. In certain applications, where one or both buck regulators power a processor, the operating state is known because it is controlled by software. In this condition, the processor can drive the MODE pin according to the operating state; consequently, it is possible to reduce the output capacitor from 10 µF to 4.7 µF because the regulator does not expect a large load variation when working in PSM mode (see Figure 47). Table 10. Suggested 10 μF Capacitors Vendor Murata TDK Panasonic Type X5R X5R X5R Model GRM188R60J106 C1608JB0J106K ECJ1VB0J106M Rev. H | Page 19 of 28 Case Size 0603 0603 0603 Voltage Rating (V) 6.3 6.3 6.3 ADP5033 Data Sheet Input Capacitor Higher value input capacitors help to reduce the input voltage ripple and improve transient response. Maximum input capacitor current is calculated using the following equation: VOUT (VIN − VOUT ) VIN To minimize supply noise, place the input capacitor as close to the VINx pin of the buck as possible. As with the output capacitor, a low ESR capacitor is recommended. The effective capacitance needed for stability, which includes temperature and dc bias effects, is a minimum of 3 µF and a maximum of 10 µF. A list of suggested capacitors is shown in Table 11. Figure 46 depicts the capacitance vs. voltage bias characteristic of a 0402 1 µF, 10 V, X5R capacitor. The voltage stability of a capacitor is strongly influenced by the capacitor size and voltage rating. In general, a capacitor in a larger package or higher voltage rating exhibits better stability. The temperature variation of the X5R dielectric is about ±15% over the −40°C to +85°C temperature range and is not a function of package or voltage rating. 1.2 Table 11. Suggested 4.7 μF Capacitors Type X5R X5R X5R Model GRM188R60J475ME19D JMK107BJ475 ECJ-0EB0J475M Voltage Rating (V) 6.3 6.3 6.3 LDO CAPACITOR SELECTION CAPACITANCE (µF) Vendor Murata Taiyo Yuden Panasonic 1.0 Case Size 0402 0402 0402 Output Capacitor Input Bypass Capacitor Connecting a 1 µF capacitor from VIN3 and VIN4 to ground reduces the circuit sensitivity to printed circuit board (PCB) layout, especially when long input traces or high source impedance is encountered. If greater than 1 µF of output capacitance is required, increase the input capacitor to match it. Table 12. Suggested 1.0 μF Capacitors Type X5R X5R X5R X5R 0.6 0.4 0.2 The ADP5033 LDOs are designed for operation with small, space-saving ceramic capacitors, but function with most commonly used capacitors as long as care is taken with the ESR value. The ESR of the output capacitor affects the stability of the LDO control loop. A minimum of 0.70 µF capacitance with an ESR of 1 Ω or less is recommended to ensure the stability of the ADP5033. Transient response to changes in load current is also affected by output capacitance. Using a larger value of output capacitance improves the transient response of the ADP5033 to large changes in load current. Vendor Murata TDK Panasonic Taiyo Yuden 0.8 Model GRM155B30J105K C1005JB0J105KT ECJ0EB0J105K LMK105BJ105MV-F Case Size 0402 0402 0402 0402 Voltage Rating (V) 6.3 6.3 6.3 10.0 Input and Output Capacitor Properties Use any good quality ceramic capacitors with the ADP5033 as long as they meet the minimum capacitance and maximum ESR requirements. Ceramic capacitors are manufactured with a variety of dielectrics, each with a different behavior over temperature and 0 0 1 2 3 4 DC BIAS VOLTAGE (V) 5 6 09788-006 I CIN ≥ I LOAD( MAX ) applied voltage. Capacitors must have a dielectric adequate to ensure the minimum capacitance over the necessary temperature range and dc bias conditions. X5R or X7R dielectrics with a voltage rating of 6.3 V or 10 V are recommended for best performance. Y5V and Z5U dielectrics are not recommended for use with any LDO because of their poor temperature and dc bias characteristics. Figure 46. Capacitance vs. Voltage Characteristic Use the following equation to determine the worst-case capacitance accounting for capacitor variation over temperature, component tolerance, and voltage: CEFF = CBIAS × (1 − TEMPCO) × (1 − TOL) where: CBIAS is the effective capacitance at the operating voltage. TEMPCO is the worst-case capacitor temperature coefficient. TOL is the worst-case component tolerance. In this example, the worst-case temperature coefficient (TEMPCO) over −40°C to +85°C is assumed to be 15% for an X5R dielectric. The tolerance of the capacitor (TOL) is assumed to be 10%, and CBIAS is 0.85 μF at 1.8 V, as shown in Figure 46. Substituting these values into the following equation, CEFF = 0.85 μF × (1 − 0.15) × (1 − 0.1) ≈ 0.65 μF Therefore, the capacitor chosen in this example meets the minimum capacitance requirement of the LDO over temperature and tolerance at the chosen output voltage. To guarantee the performance of the ADP5033, it is imperative that the effects of dc bias, temperature, and tolerances on the behavior of the capacitors be evaluated for each application. Rev. H | Page 20 of 28 Data Sheet ADP5033 POWER DISSIPATION AND THERMAL CONSIDERATIONS The ADP5033 is a highly efficient micropower management unit (µPMU), and, in most cases, the power dissipated in the device is not a concern. However, if the device operates at high ambient temperatures and maximum loading condition, the junction temperature can reach the maximum allowable operating limit (125°C). When the temperature exceeds 150°C, the ADP5033 turns off all the regulators, allowing the device to cool down. When the die temperature falls below 130°C, the ADP5033 resumes normal operation. This section provides guidelines to calculate the power dissipated in the device and ensure that the ADP5033 operates below the maximum allowable junction temperature. POUT × 100% PIN The power loss of the buck regulator is approximated by PLOSS = PDBUCK + PL (3) where: PDBUCK is the power dissipation on one of the ADP5033 buck regulators. PL is the inductor power losses. The inductor losses are external to the device, and they do not have any effect on the die temperature. The inductor losses are estimated (without core losses) by PL ≈ IOUT1(RMS)2 × DCRL The efficiency for each regulator on the ADP5033 is given by η= BUCK REGULATOR POWER DISSIPATION (1) where: DCRL is the inductor series resistance. IOUT1(RMS) is the rms load current of the buck regulator. I OUT 1( RMS ) = I OUT1 × 1 + where: η is the efficiency. PIN is the input power. POUT is the output power. (4) r 12 (5) where r is the normalized inductor ripple current r = VOUT1 × (1 − D)/(IOUT1 × L × fSW) Power loss is given by PLOSS = PIN − POUT (2a) PLOSS = POUT (1− η)/η (2b) or Power dissipation can be calculated in several ways. The most intuitive and practical is to measure the power dissipated at the input and all the outputs. Perform the measurements at the worst-case conditions (voltages, currents, and temperature). The difference between input and output power is dissipated in the device and the inductor. Use Equation 4 to derive the power lost in the inductor and, from this, use Equation 3 to calculate the power dissipation in the ADP5033 buck converter. A second method to estimate the power dissipation uses the efficiency curves provided for the buck regulator, and the power lost on each LDO can be calculated using Equation 12. When the buck efficiency is known, use Equation 2b to derive the total power lost in the buck regulator and inductor, use Equation 4 to derive the power lost in the inductor, and then calculate the power dissipation in the buck converter using Equation 3. Add the power dissipated in the buck and in the two LDOs to find the total dissipated power. Note that the buck efficiency curves are typical values and may not be provided for all possible combinations of VIN, VOUT, and IOUT. To account for these variations, it is necessary to include a safety margin when calculating the power dissipated in the buck. (6) where: L is the inductance. fSW is the switching frequency. D is the duty cycle. D = VOUT1/VIN1 (7) The ADP5033 buck regulator power dissipation, PDBUCK, includes the power switch conductive losses, the switch losses, and the transition losses of each channel. There are other sources of loss, but these are generally less significant at high output load currents, where the thermal limit of the application is. Equation 8 captures the calculation that must be made to estimate the power dissipation in the buck regulator. PDBUCK = PCOND + PSW + PTRAN (8) The power switch conductive losses are due to the output current, IOUT1, flowing through the P-MOSFET and the N-MOSFET power switches that have internal resistance, RDSON-P and RDSON-N. The amount of conductive power loss is found by PCOND = [RDSON-P × D + RDSON-N × (1 − D)] × IOUT1(RMS)2 (9) where RDSON-P is approximately 0.2 Ω, and RDSON-N is approximately 0.16 Ω at 25°C junction temperature and VIN1 = VIN2 = 3.6 V. At VIN1 = VIN2 = 2.3 V, these values change to 0.31 Ω and 0.21 Ω, respectively, and at VIN1 = VIN2 = 5.5 V, the values are 0.16 Ω and 0.14 Ω, respectively. A third way to estimate the power dissipation is analytical and involves modeling the losses in the buck circuit provided by Equation 8 to Equation 11 and the losses in the LDO provided by Equation 12. Rev. H | Page 21 of 28 ADP5033 Data Sheet Switching losses are associated with the current drawn by the driver to turn on and turn off the power devices at the switching frequency. The amount of switching power loss is given by PSW = (CGATE-P + CGATE-N) × VIN12 × fSW (10) where: CGATE-P is the P-MOSFET gate capacitance. CGATE-N is the N-MOSFET gate capacitance. The transition losses occur because the P-channel power MOSFET cannot be turned on or off instantaneously, and the SW node takes some time to slew from near ground to near VOUT1 (and from VOUT1 to ground). The amount of transition loss is calculated by (11) where tRISE and tFALL are the rise time and the fall time of the switching node, SW. For the ADP5033, the rise and fall times of SW are in the order of 5 ns. If the preceding equations and parameters are used for estimating the converter efficiency, it must be noted that the equations do not describe all of the converter losses, and the parameter values given are typical numbers. The converter performance also depends on the choice of passive components and board layout; therefore, a sufficient safety margin should be included in the estimate. LDO Regulator Power Dissipation The power loss of an LDO regulator is given by PDLDO = [(VIN − VOUT) × ILOAD] + (VIN × IGND) In cases where the board temperature TA is known, the thermal resistance parameter, θJA, can be used to estimate the junction temperature rise. TJ is calculated from TA and PD using the formula TJ = TA + (PD × θJA) For the ADP5033, the total of (CGATE-P + CGATE-N) is approximately 150 pF. PTRAN = VIN1 × IOUT1 × (tRISE + tFALL) × fSW JUNCTION TEMPERATURE (12) where: ILOAD is the load current of the LDO regulator. VIN and VOUT are input and output voltages of the LDO, respectively. IGND is the ground current of the LDO regulator. The typical θJA value for the 16-ball, 0.5 mm pitch WLCSP is 57°C/W (see Table 7). A very important factor to consider is that θJA is based on a 4-layer 4 in × 3 in, 2.5 oz copper, as per JEDEC standard, and real applications may use different sizes and layers. It is important to maximize the copper used to remove the heat from the device. Copper exposed to air dissipates heat better than copper used in the inner layers. The exposed pad should be connected to the ground plane with several vias. If the case temperature can be measured, the junction temperature is calculated by TJ = TC + (PD × ΨJB) (15) where TC is the case temperature and ΨJB is the junction-toboard thermal resistance provided in Table 7. When designing an application for a particular ambient temperature range, calculate the expected ADP5033 power dissipation (PD) due to the losses of all channels by using the Equation 8 to Equation 13. From this power calculation, the junction temperature, TJ, can be estimated using Equation 14. The reliable operation of the converter and the two LDO regulators can be achieved only if the estimated die junction temperature of the ADP5033 (Equation 14) is less than 125°C. Reliability and mean time between failures (MTBF) is highly affected by increasing the junction temperature. Additional information about product reliability can be found in the ADI Reliability Handbook, which can be found at www.analog.com/reliability_handbook. Power dissipation due to the ground current is small, and it can be ignored. The total power dissipation in the ADP5033 simplifies to PD = PDBUCK1 + PDBUCK2 + PDLDO1 + PDLDO2 (14) (13) Rev. H | Page 22 of 28 Data Sheet ADP5033 PCB LAYOUT GUIDELINES Poor layout can affect ADP5033 performance, causing electromagnetic interference (EMI) and electromagnetic compatibility (EMC) problems, ground bounce, and voltage losses. Poor layout can also affect regulation and stability. A good layout is implemented using the following guidelines: • • • • Place the inductor, input capacitor, and output capacitor close to the IC using short tracks. These components carry high switching frequencies, and large tracks act as antennas. Route the output voltage path away from the inductor and SW node to minimize noise and magnetic interference. • Rev. H | Page 23 of 28 Maximize the size of ground metal on the component side to help with thermal dissipation. Use a ground plane with several vias connecting to the component side ground to further reduce noise interference on sensitive circuit nodes. Connect VIN1 and VIN2 together close to the IC using short tracks. ADP5033 Data Sheet TYPICAL APPLICATION SCHEMATIC ADP5033 VCORE PROCESSOR L1 1µH SW1 VIN1 VCORE VOUT1 C1 4.7µF BUCK1 PGND1 C5 4.7µF ALWAYS ON ENA VIN: 2.3V TO 5.5V ACT ENB BK1 BK2 LD1 LD2 MODE VIN2 SW2 C2 4.7µF BUCK2 L2 1µH FROM VCORE (1.7V MIN) VIN3 LDO1 VIN4 LDO2 C6 4.7µF VOUT3 C7 1µF C3 1µF C4 1µF VIO VOUT2 PGND2 FROM VIO (1.7V MIN) GPIO VIO VOUT4 C8 1µF ANALOG SUBSYSTEM VANA VDIG AGND Figure 47. Processor System Power Management with PSM/PWM Control Rev. H | Page 24 of 28 09788-152 ON OFF Data Sheet ADP5033 OUTLINE DIMENSIONS 2.040 2.000 SQ 1.960 4 3 2 1 A BALL A1 IDENTIFIER B 1.50 REF C D 0.50 REF SEATING PLANE BOTTOM VIEW (BALL SIDE UP) SIDE VIEW 0.390 0.360 0.330 COPLANARITY 0.04 0.360 0.320 0.280 0.270 0.240 0.210 Figure 48. 16-Ball Wafer Level Chip Scale Package [WLCSP] Back-Coating Included (CB-16-8) Dimensions shown in millimeters Rev. H | Page 25 of 28 10-19-2012-B 0.660 0.600 0.540 TOP VIEW (BALL SIDE DOWN) ADP5033 Data Sheet ORDERING GUIDE Model 1 ADP5033ACBZ-1-R7 Temperature Range −40°C to +125°C ADP5033ACBZ-2-R7 −40°C to +125°C ADP5033ACBZ-3-R7 −40°C to +125°C ADP5033ACBZ-4-R7 −40°C to +125°C ADP5033ACBZ-5-R7 −40°C to +125°C ADP5033ACBZ-6-R7 −40°C to +125°C ADP5033ACBZ-7-R7 −40°C to +125°C ADP5033ACBZ-8-R7 −40°C to +125°C ADP5033ACBZ-9-R7 −40°C to +125°C ADP5033ACBZ-10R7 −40°C to +125°C ADP5033ACBZ-11R7 −40°C to +125°C Output Voltage (V) 2 VOUT1: 1.2 V, VOUT2: 3.3 V, VOUT3: 2.8 V, VOUT4: 1.8 V VOUT1: 1.8 V, VOUT2: 2.8 V, VOUT3: 2.8 V, VOUT4: 3.0 V VOUT1: 3.0 V, VOUT2: 1.2 V, VOUT3: 1.8 V, VOUT4: 3.0 V VOUT1: 0.9 V, VOUT2: 0.9 V, VOUT3: 3.0 V, VOUT4: 2.8 V VOUT1: 3.3 V, VOUT2: 1.8 V, VOUT3: 1.2 V, VOUT4: 1.5 V VOUT1: 1.8 V, VOUT2: 2.5 V, VOUT3: 3.0 V, VOUT4: 3.0 V VOUT1: 1.1 V, VOUT2: 1.8 V, VOUT3: 2.5 V, VOUT4: 3.2 V VOUT1: 2.8 V, VOUT2: 1.5 V, VOUT3: 2.8 V, VOUT4: 1.8 V VOUT1: 1.1 V, VOUT2: 1.8 V, VOUT3: 1.2 V, VOUT4: 3.2 V VOUT1: 1.8 V, VOUT2: 3.3 V, VOUT3: 1.8 V, VOUT4: 3.3 V VOUT1: 1.2 V, VOUT2: 3.3 V, VOUT3: 1.8 V, VOUT4: 2.5 V ENA Controlled Channels 3 BUCK2, LDO1 Package Description 16-Ball WLCSP Package Option CB-16-8 Marking Code LHX BUCK1, BUCK2, LDO1 16-Ball WLCSP CB-16-8 LMD UVLO: low, pull-downs on all channels BUCK1, LDO1, LDO2 16-Ball WLCSP CB-16-8 LNC UVLO: low, pull-downs disabled BUCK1, BUCK2 16-Ball WLCSP CB-16-8 LNR UVLO: low, pull-downs on all channels BUCK1 16-Ball WLCSP CB-16-8 LQ3 UVLO: low, pull-downs on all channels BUCK1, LDO1 16-Ball WLCSP CB-16-8 LQ5 UVLO: low, pull-downs on all channels BUCK1 16-Ball WLCSP CB-16-8 LRB UVLO: low, pull-downs on all channels BUCK1, BUCK2, LDO2 16-Ball WLCSP CB-16-8 LRC UVLO: low, pull-downs on all channels BUCK1 16-Ball WLCSP CB-16-8 LRD UVLO: low, pull-downs on all channels BUCK1, LDO1 16-Ball WLCSP CB-16-8 LV6 UVLO: low, pull-downs on all channels BUCK1, BUCK2 16-Ball WLCSP CB-16-8 LV7 Options UVLO: low, pull-downs on buck channels only UVLO: low, pull-downs on all channels ADP5033-1-EVALZ Evaluation Board for ADP5033ACBZ1-R7 1 Z = RoHS Compliant Part. 2 For additional options, contact a local sales or distribution representative. Additional options available include the following: BUCK1 and BUCK2: 3.3 V, 3.0 V, 2.8 V, 2.5 V, 2.3 V, 2.0 V, 1.8 V, 1.6 V, 1.5 V, 1.4 V, 1.3 V, 1.2 V, 1.1 V, 1.0 V, or 0.9 V. LDO1 and LDO2: 3.3 V, 3.0 V, 2.8 V, 2.5 V, 2.25 V, 2 V, 1.8 V, 1.7 V, 1.6 V, 1.5 V, 1.2 V, 1.1 V, 1.0 V, 0.9 V, or 0.8 V. UVLO: low or high. In addition, for BUCK1, BUCK2, LDO1, and LDO2, active pull-down resistor is programmable to be either enabled or disabled. 3 ENA activated channels (ENB controls the other channels). Rev. H | Page 26 of 28 Data Sheet ADP5033 NOTES Rev. H | Page 27 of 28 ADP5033 Data Sheet NOTES ©2011–2019 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09788-0-3/19(H) Rev. H | Page 28 of 28