DS1088E
Fixed-Frequency EconOscillator™
General Description
Benefits and Features
The DS1088E is a low-cost clock generator that produces a square-wave output without external timing components. The fixed-frequency oscillator is available in a
factory-calibrated frequency of 133MHz. The device has a
power-down pin for power-sensitive applications.
● Factory-Programmed, 133MHz Square-Wave
Generator
● Single Output
● No External Timing Components Required
● 2.85V to 3.6V Supply
● Power-Down Mode
Applications
●
●
●
●
●
●
●
● Wide Temperature Range (-40°C to +95°C)
Optical Modules
Printers
Copiers
Automotive Telematics
Computer Peripherals
POS Terminals
Cable Modems
EconOscillator is a trademark of Maxim Integrated Products, Inc.
Ordering Information appears at end of data sheet.
For related parts and recommended products to use with this part, refer
to www.maximintegrated.com/DS1088E.related.
Typical Operating Circuit
133MHz
OUTPUT
OUT
DNC
DS1088E
VCC
VCC
DNC
VCC
PDN
GND
GND
DECOUPLING CAPACITORS
(0.1µF AND 0.01µF)
19-6853; Rev 0; 11/13
VCC
DS1088E
Fixed-Frequency EconOscillator™
Absolute Maximum Ratings
(Voltages relative to ground.)
Voltage Range on VCC..........................................-0.5V to +6.0V
Voltage Range on PDN............................-0.5V to (VCC + 0.5V)*
Operating Temperature Range............................ -40°C to +95°C
Storage Temperature Range............................. -55°C to +125°C
Lead Temperature (soldering, 10s).................................. +300°C
Soldering Temperature (reflow)........................................+260°C
*Not to exceed +6.0V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Recommended Operating Conditions
(TA = -40NC to +95NC, unless otherwise noted.)
PARAMETER
SYMBOL
Supply Voltage
VCC
High-Level Input Voltage (PDN)
VIH
Low-Level Input Voltage (PDN)
VIL
CONDITIONS
(Note 1)
MIN
TYP
2.85
0.7 x VCC
-0.3
MAX
UNITS
3.63
V
VCC + 0.3
V
0.3 x VCC
V
DC Electrical Characteristics
(VCC = 2.85V to 3.63V, TA = -40NC to +95NC, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
High-Level Output Voltage (OUT)
VOH
IOH = -4mA, VCC = MIN
Low-Level Output Voltage (OUT)
VOL
IOL = 4mA
High-Level Input Current (PDN)
IIH
VCC = 3.63V
Low-Level Input Current (PDN)
IIL
VIL = 0V
Supply Current (Active)
ICC
VCC = 3.63V, CL = 15pF, fO = 133MHz
Standby Current (Power-Down)
ICCQ
MIN
TYP
MAX
VCC 0.4
UNITS
V
0.4
V
1
μA
24
mA
10
μA
MAX
UNITS
-1
μA
15
Power-down mode
Oscillator Characteristics
(VCC = 2.85V to 3.63V, TA = -40NC to +95NC, unless otherwise noted.)
PARAMETER
Output Frequency Range
Available
Output Frequency Tolerance
www.maximintegrated.com
SYMBOL
CONDITIONS
MIN
133.3
fO
Δf/fO
TYP
-15
MHz
+5
%
Maxim Integrated │ 2
DS1088E
Fixed-Frequency EconOscillator™
AC Electrical Characteristics
(VCC = 2.85V to 3.63V, TA = -40NC to +95NC, unless otherwise noted.)
PARAMETER
Power-Up Time
OUT Disabled After Entering
Power-Down Mode
Load Capacitance
Output Duty Cycle (OUT)
SYMBOL
MAX
UNITS
(Note 2)
100
μs
tPDN
(Note 3)
7
μs
CL
(Note 4)
50
pF
tPOR +
tSTAB
CONDITIONS
MIN
TYP
15
55
%
Note 1: All voltages are referenced to ground.
Note 2: This indicates the time elapsed between power-up and the output becoming active. An on-chip delay is intentionally introduced to allow the oscillator to stabilize. tSTAB is equivalent to approximately 512 clock cycles and will depend on the programmed oscillator frequency.
Note 3: Output disabled in two cycles or less of the output frequency.
Note 4: Output voltage swings may be impaired at high frequencies combined with high-output loading.
www.maximintegrated.com
Maxim Integrated │ 3
DS1088E
Fixed-Frequency EconOscillator™
Typical Operating Characteristics
(VCC = 3.3V, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
SUPPLY CURRENT
vs. TEMPERATURE
12.8
14
toc01
VCC = 3.3V
12.6
13.5
12
11.8
11.6
11.4
12.5
12
11.5
TA = +25oC
11
10.5
11.2
10
-40
-25
-10
5
20
35
50
65
80
95
2.85
3
55
toc04
SHUTDOWN SUPPLY CURRENT (µA)
DUTY CYCLE (%)
53
52
51
50
49
2.85
3
3.15
3.3
3.45
3.6
3.45
3.6
3
3.15
3.3
3.45
DUTY CYCLE
vs. TEMPERATURE
50.6
2.2
50.4
2.18
50.2
2.16
2.14
2.12
2.1
VCC = 3.3V
2.08
50
49.6
49.4
49
48.8
-10
5
20
35
50
65
80
VCC = 3.3V
49.2
2.04
-25
toc06
49.8
2.06
SUPPLY VOLTAGE (V)
95
TEMPERATURE (oC)
3.6
50.8
2.22
-40
2.85
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
toc05
toc03
TA = +25oC
SUPPLY VOLTAGE (V)
2.24
TA = +25oC
54
3.3
DUTY CYCLE (%)
DUTY CYCLE
vs. SUPPLY VOLTAGE
3.15
0.9
0.85
0.8
0.75
0.7
0.65
0.6
0.55
0.5
0.45
0.4
0.35
0.3
0.25
0.2
0.15
FREQUENCY ERROR
vs. SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
TEMPERATURE (oC)
48
FREQUENCY ERROR (%)
13
12.2
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
12.4
11
toc02
-40
-25
-10
5
20
35
50
65
80
95
TEMPERATURE (oC)
FREQUENCY ERROR
vs. TEMPERATURE
toc07
2.5
FREQUENCY ERROR (%)
2
1.5
1
0.5
VCC = 3.3V
0
-0.5
-40 -25 -10
5
20
35
50
65
80
95
TEMPERATURE (oC)
www.maximintegrated.com
Maxim Integrated │ 4
DS1088E
Fixed-Frequency EconOscillator™
Pin Configuration
TOP VIEW
DNC DNC PDN GND
8
7
6
5
DS1088E
EP
+
1
2
OUT VCC
3
4
VCC GND
TDFN
2mm x 3mm
Pin Description
PIN
NAME
1
OUT
Oscillator Output
FUNCTION
2, 3
VCC
Power Supply
4, 5
GND
Ground
6
PDN
Active-Low Power-Down. When the pin is high, the oscillator is enabled. When the pin is low,
the oscillator is disabled (power-down mode).
7, 8
DNC
Do Not Connect. The DNC pins are internally connected to ground.
EP
—
www.maximintegrated.com
Exposed Pad. Internally connected to GND. Connect to the ground plane to minimize noise
injection. Not intended for use as the device electrical ground.
Maxim Integrated │ 5
DS1088E
Fixed-Frequency EconOscillator™
Detailed Description
Output Frequency
The DS1088E is a low-cost clock generator that produces a square-wave output without external timing components. The fixed-frequency oscillator is available in a
factory-calibrated frequency of 133MHz. The device has a
power-down pin for power-sensitive applications. A block
diagram of the device is shown in Figure 1.
VCC
VCC
EEPROM
CONTROL
VOLTAGECONTROLLED
OSCILLATOR
80MHz TO 160MHz
PRESCALER
÷ BY 1, 2, 4...256
GND
DS1088E
www.maximintegrated.com
Power-Down Mode
The PDN pin disables the internal oscillator and the
oscillator output for power-sensitive applications. The
power-down pin must remain low for at least two output
frequency cycles plus 10µs for deglitching purposes. On
power-up, the output is disabled until power is stable and
the voltage-controlled oscillator has generated 512 clock
cycles.
Applications Information
PDN
Figure 1. Block Diagram
The internal oscillator frequency is divided by the factoryprogrammed prescaler to produce an output frequency of
133MHz.
OUT
133MHz
Power-Supply Decoupling
To achieve the best results when using the device, the
power supply must be decoupled with 0.01µF and 0.1µF
high-quality, ceramic, surface-mount capacitors. Surfacemount components minimize lead inductance, which
improves performance, and tend to have adequate highfrequency response for decoupling applications. These
capacitors should be placed as close as possible to the
VCC and GND pins.
Maxim Integrated │ 6
DS1088E
Fixed-Frequency EconOscillator™
Ordering Information
PART
DS1088EN-133+T
FREQUENCY (MHz)
TEMP RANGE
PIN-PACKAGE
133.3
-40°C to +95°C
8 TDFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
*EP = Exposed pad.
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
OUTLINE NO.
LAND PATTERN NO.
8 TDFN-EP
T823+1
21-0174
90-0091
Chip Information
SUBSTRATE CONNECTED TO GROUND
www.maximintegrated.com
Maxim Integrated │ 7
DS1088E
Fixed-Frequency EconOscillator™
Revision History
REVISION
NUMBER
REVISION
DATE
0
11/13
DESCRIPTION
Initial release
PAGES
CHANGED
—
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2013 Maxim Integrated Products, Inc. │ 8
很抱歉,暂时无法提供与“DS1088EN-133+T”相匹配的价格&库存,您可以联系我们找货
免费人工找货