Rev 1; 11/03
10-Tap Silicon Delay Line
The DS1110 delay line is an improved replacement for
the DS1010. It has ten equally spaced taps providing
delays from 5ns to 500ns. The devices are offered in a
standard 16-pin SO or 14-pin TSSOP. The DS1110 series
delay lines provide a nominal accuracy of ±5% or ±2ns,
whichever is greater, at 5V and +25°C. The DS1110
reproduces the input logic state at the tap 10 output after
a fixed delay as specified by the dash number extension
of the part number. The DS1110 is designed to produce
both leading- and trailing-edge delays with equal precision. Each tap is capable of driving up to ten 74LS type
loads. Dallas Semiconductor can customize standard
products to meet special needs.
Applications
Features
♦ All-Silicon, 5V, 10-Tap Delay Line
♦ Improved, Drop-In Replacement for the DS1010
♦ 10 Taps Equally Spaced
♦ Delays are Stable and Precise
♦ Leading- and Trailing-Edge Accuracy
♦ Delay Tolerance ±5% or ±2ns, whichever is
Greater, at 5V and +25°C
♦ Economical
♦ Auto-Insertable, Low Profile
♦ Low-Power CMOS
♦ TTL/CMOS Compatible
♦ Vapor Phase, IR, and Wave Solderable
Communications Equipment
♦ Fast-Turn Prototypes
Medical Devices
Automated Test Equipment
♦ Delays Specified Over Commercial and Industrial
Temperature Ranges
PC Peripheral Devices
♦ Custom Delays Available
♦ Standard 16-Pin SO or 14-Pin TSSOP
Pin Configurations
TOP VIEW
IN 1
N.C.
2
TAP2
3
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
DS1110E-XXX
-40°C to +85°C
14 TSSOP
DS1110S-XXX
-40°C to +85°C
16 SO
14 VCC
13 TAP1
DS1110E
12 TAP3
TAP4 4
11 TAP5
TAP6 5
10 TAP7
TAP8 6
9
TAP9
GND 7
8
TAP10
Selector Guide appears at end of data sheet.
TSSOP
Pin Configurations continued at end of data sheet.
_____________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
DS1110
General Description
DS1110
10-Tap Silicon Delay Line
ABSOLUTE MAXIMUM RATINGS
Voltage on Any Pin Relative to Ground .................-0.5V to +6.0V
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-55°C to +125°C
Soldering Temperature...................See IPC/JEDEC J-STD-020A
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = 5.0V ±5%, TA = -40°C to +85°C.)
MIN
TYP
MAX
UNITS
Supply Voltage
PARAMETER
SYMBOL
VCC
(Note 1)
4.75
5.0
5.25
V
High-Level Input Voltage
VIH
(Note 1)
2.4
VCC
+ 0.3
V
Low-Level Input Voltage
VIL
(Note 1)
-0.3
+0.8
V
0V ≤ VI ≤ VCC
-1.0
Input Leakage Current
II
CONDITIONS
Active Current
ICC
VCC = max, period = min (Note 2)
High-Level Output Current
IOH
VCC = min, VOH = 2.3V
Low-Level Output Current
IOL
VCC = min, VOL = 0.5V
40
+1.0
µA
150
mA
-1.0
mA
12
mA
AC ELECTRICAL CHARACTERISTICS
(VCC = 5.0V ±5%, TA = -40°C to +85°C.)
PARAMETER
SYMBOL
Input Pulse Width
tWI
Input-to-Tap Delay
(Delays ≤ 40ns)
tPLH
tPHL
Input-to-Tap Delay
(Delays > 40ns)
tPLH
tPHL
Power-Up Time
Input Period
2
CONDITIONS
(Note 6)
MIN
TYP
+25°C, 5.0V (Notes 3, 5, 6, 7, 9)
-2
Table 1
+2
0°C to +70°C (Notes 4–7)
-3
Table 1
+3
-40°C to +85°C (Notes 4–7)
-4
Table 1
+4
+25°C, 5.0V (Notes 3, 5, 6, 7, 9)
-5
Table 1
+5
0°C to +70°C (Notes 4–7)
-8
Table 1
+8
-40°C to +85°C (Notes 4–7)
-13
Table 1
+13
200
(Note 8)
______________________________________________________________________
UNITS
ns
tPU
Period
MAX
10% of
tap 10
2 (tWI) or 20,
whichever
is greater
ns
%
ms
ns
10-Tap Silicon Delay Line
DS1110
CAPACITANCE
(TA = +25°C.)
PARAMETER
Input Capacitance
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
CONDITIONS
SYMBOL
MIN
TYP
MAX
UNITS
5
10
pF
CIN
All voltages are referenced to ground.
Measured with outputs open.
Initial tolerances are ± with respect to the nominal value at +25°C and VCC = 5.0V for both leading and trailing edges.
Temperature and voltage tolerances are with respect to the actual delay measured over stated temperature range and a 4.75V
to 5.25V range.
Intermediate delay values are available on a custom basis.
See Test Conditions section.
All tap delays tend to vary unidirectionally with temperature or voltage changes. For example, if tap 1 slows down, all other
taps also slow down; tap 3 can never be faster than tap 2.
Pulse width and period specifications may be exceeded; however, accuracy is application sensitive (decoupling, layout, etc.)
For Tap 1 delays greater than 20ns, the tolerance is ±3ns or ±5%, whichever is greater.
Typical Operating Characteristics
(VCC = 5.0V, TA = +25°C, unless otherwise noted.)
DS1110-50 ACTIVE CURRENT
vs. INPUT FREQUENCY
DS1110-500 ACTIVE CURRENT
vs. INPUT FREQUENCY
180
160
ACTIVE CURRENT (mA)
30
25
20
15
10
140
120
100
80
60
40
15pF LOAD/TAP
VCC = 5.25V
5
DS1110 toc02
35
15pF LOAD/TAP
VCC = 5.25V
20
0
0
0.1
0.1
10
1.0
1.0
100
10
FREQUENCY (MHz)
FREQUENCY (MHz)
DS1110-500 TAP 10 DELAY
vs. TEMPERATURE
DS1110-50 TAP 10 DELAY
vs. TEMPERATURE
54
DS1110 toc03
575
550
DS1110 toc04
ACTIVE CURRENT (mA)
200
DS1110 toc01
40
53
52
DELAY (ns)
DELAY (ns)
525
500
51
50
49
475
48
450
47
500kHz INPUT
46
425
-40
-15
10
35
TEMPERATURE (°C)
60
85
-40
-15
10
35
60
85
TEMPERATURE (°C)
_____________________________________________________________________
3
Typical Operating Characteristics (continued)
(VCC = 5.0V, TA = +25°C, unless otherwise noted.)
DS1110-500 DELAY vs. TAP
DS1110-50 DELAY vs. TAP
400
FALLING EDGE
45
40
350
35
300
DELAY (ns)
RISING EDGE
250
200
150
30
RISING EDGE
25
20
15
100
10
500kHz INPUT
50
5
0
0
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
TAP
TAP
DS1110-500 TAP 10 DELAY
vs. VOLTAGE
DS1110-50 TAP 10 DELAY
vs. VOLTAGE
55
DS1110 toc07
540
9
10
DS1110 toc08
DELAY (ns)
DS1110 toc06
FALLING EDGE
450
50
DS1110 toc05
500
53
520
FALLING EDGE
DELAY (ns)
DELAY (ns)
DS1110
10-Tap Silicon Delay Line
500
51
FALLING EDGE
49
RISING EDGE
RISING EDGE
480
47
500kHz INPUT
460
4.750
4.875
5.000
5.125
45
4.750
5.250
4.875
5.000
5.125
5.250
VOLTAGE (V)
VOLTAGE (V)
Pin Description
PIN
NAME
4
FUNCTION
TSSOP
SO
1
1
IN
2
2, 3, 15
N.C.
No Connection
7
8
GND
Ground
13, 3, 12, 4, 11,
5, 10, 6, 9, 8
14, 4, 13, 5, 12, 6, 11,
7, 10, 9
Tap 1–Tap 10
14
16
VCC
Input
Tap Output Number
5.0V
______________________________________________________________________
10-Tap Silicon Delay Line
Table 1. Part Number by Delay (tPHL, tPLH)
The DS1110 delay line is an improved replacement for
the DS1010. It has ten equally spaced taps providing
delays from 5ns to 500ns. The devices are offered in a
standard 16-pin SO or 14-pin TSSOP. The DS1110
series delay lines provide a nominal accuracy of ±5%
or ±2ns, whichever is greater, at 5V and +25°C. The
DS1110 reproduces the input logic state at the tap 10
output after a fixed delay as specified by the dash
number extension of the part number. The DS1110 is
designed to produce both leading- and trailing-edge
delays with equal precision. Each tap is capable of driving up to ten 74LS type loads. Dallas Semiconductor
can customize standard products to meet special
needs. For special requests call 972-371-4348.
PART
TOTAL DELAY* (ns)
DELAY/TAP (ns)
DS1110-50
50
5
DS1110-60
60
6
DS1110-75
75
7.5
DS1110-80
80
8
DS1110-100
100
10
DS1110-125
125
12.5
DS1110-150
150
15
DS1110-175
175
17.5
DS1110-200
200
20
DS1110-250
250
25
DS1110-300
300
30
DS1110-350
350
35
DS1110-400
400
40
DS1110-450
450
45
DS1110-500
500
50
*Custom delays are available.
TAP1
TAP2
TAP9
TAP10
IN
10%
10%
10%
10%
Figure 1. Logic Diagram
PERIOD
tFALL
tRISE
VIH
2.2V
2.2V
1.5V
1.5V
1.5V
0.8V
0.8V
IN VIL
tWI
tWI
tPLH
tPLH
1.5V
1.5V
OUT
Figure 2. Timing Diagram: Silicon Delay Line
_____________________________________________________________________
5
DS1110
Detailed Description
DS1110
10-Tap Silicon Delay Line
Terminology
Period: The time elapsed between the leading edge of
the first pulse and the leading edge of the following pulse.
t WI (Pulse Width): The elapsed time on the pulse
between the 1.5V point on the leading edge and the
1.5V point on the trailing edge, or the 1.5V point on the
trailing edge and the 1.5V point on the leading edge.
tRISE (Input Rise Time): The elapsed time between the
20% and the 80% point on the leading edge of the
input pulse.
tFALL (Input Fall Time): The elapsed time between the
80% and the 20% point on the trailing edge of the
input pulse.
tPLH (Time Delay, Rising): The elapsed time between
the 1.5V point on the leading edge of the input pulse
and the 1.5V point on the leading edge of any tap output pulse.
tPHL (Time Delay, Falling): The elapsed time between
the 1.5V point on the trailing edge of the input pulse
and the 1.5V point on the trailing edge of any tap output pulse.
Test Setup Description
Figure 3 illustrates the hardware configuration used for
measuring the timing parameters on the DS1110. A
precision pulse generator under software control produces the input waveform. Time delays are measured
by a time interval counter (20ps resolution) connected
PULSE
GENERATOR
START
Z0 = 50Ω
TIME
INTERVAL
COUNTER
STOP
VHF SWITCH
CONTROL UNIT
DEVICE UNDER TEST
Figure 3. Test Circuit
6
______________________________________________________________________
10-Tap Silicon Delay Line
Output
Each output is loaded with the equivalent of one 74FO4
input gate. Delay is measured at the 1.5V level on the
rising and falling edge.
Chip Information
TRANSISTOR COUNT: 6813
DS1110
between the input and each tap. Each tap is selected
and connected to the counter by a VHF switch-control
unit. All measurements are fully automated, with each
instrument controlled by a central computer over an
IEEE-488 bus.
Table 2. Test Conditions
INPUT
CONDITION
Ambient Temperature
+25°C ±3°C
Supply Voltage (VCC)
5.0V ±0.1V
High = 3.0V ±0.1V
Input Pulse
Low = 0.0V ±0.1V
Source Impedance
50Ω max
Rise and Fall Time
3ns max
Pulse Width
500ns (1µs for -500ns)
Period
1µs (2µs for -500ns)
Note: The above conditions are for test only and do not restrict
the operation of the device under other data sheet conditions.
Selector Guide
TEMP RANGE
PINPACKAGE
TOTAL
DELAY
(ns)*
DS1110E-50
-40°C to +85°C
14 TSSOP
50
DS1110E-60
-40°C to +85°C
14 TSSOP
60
DS1110E-75
-40°C to +85°C
14 TSSOP
DS1110E-80
-40°C to +85°C
14 TSSOP
DS1110E-100
-40°C to +85°C
DS1110E-125
DS1110E-150
TOTAL
DELAY
(ns)*
TEMP RANGE
PINPACKAGE
DS1110S-50
-40°C to +85°C
16 SO
50
DS1110S-60
-40°C to +85°C
16 SO
60
75
DS1110S-75
-40°C to +85°C
16 SO
75
80
DS1110S-80
-40°C to +85°C
16 SO
80
14 TSSOP
100
DS1110S-100
-40°C to +85°C
16 SO
100
-40°C to +85°C
14 TSSOP
125
DS1110S-125
-40°C to +85°C
16 SO
125
-40°C to +85°C
14 TSSOP
150
DS1110S-150
-40°C to +85°C
16 SO
150
DS1110E-175
-40°C to +85°C
14 TSSOP
175
DS1110S-175
-40°C to +85°C
16 SO
175
DS1110E-200
-40°C to +85°C
14 TSSOP
200
DS1110S-200
-40°C to +85°C
16 SO
200
DS1110E-250
-40°C to +85°C
14 TSSOP
250
DS1110S-250
-40°C to +85°C
16 SO
250
DS1110E-300
-40°C to +85°C
14 TSSOP
300
DS1110S-300
-40°C to +85°C
16 SO
300
DS1110E-350
-40°C to +85°C
14 TSSOP
350
DS1110S-350
-40°C to +85°C
16 SO
350
DS1110E-400
-40°C to +85°C
14 TSSOP
400
DS1110S-400
-40°C to +85°C
16 SO
400
DS1110E-450
-40°C to +85°C
14 TSSOP
450
DS1110S-450
-40°C to +85°C
16 SO
450
DS1110E-500
-40°C to +85°C
14 TSSOP
500
DS1110S-500
-40°C to +85°C
16 SO
500
PART
PART
*Custom delays are available.
_____________________________________________________________________
7
DS1110
10-Tap Silicon Delay Line
Pin Configurations (continued)
Package Information
For the latest package outline information, go to www.maxim-ic.
com/packages.
TOP VIEW
IN1 1
16 VCC
N.C. 2
15 N.C.
N.C.
3
TAP2
4
14 TAP1
DS1110S
13 TAP3
TAP4 5
12 TAP5
TAP6 6
11 TAP7
TAP8 7
10 TAP9
GND 8
9
TAP10
SO (300mil)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2002 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.