DS21348/DS21Q348
3.3V E1/T1/J1 Line Interface
www.maxim-ic.com
FEATURES
PIN CONFIGURATIONS
111
Complete E1, T1, or J1 Line Interface Unit
(LIU)
Supports Both Long-Haul And Short-Haul
Trunks
Internal Software-Selectable Receive-Side
Termination for 75Ω/100Ω/120Ω
3.3V Power Supply
32-Bit or 128-Bit Crystal-Less Jitter
Attenuator Requires Only a 2.048MHz
Master Clock for Both E1 and T1 with
Option to Use 1.544MHz for T1
Generates the Appropriate Line Build-Outs,
with and without Return loss, for E1 and
DSX-1 and CSU Line Build-Outs for T1
AMI, HDB3, and B8ZS, Encoding/Decoding
16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz Clock Output Synthesized to
Recovered Clock
Programmable Monitor Mode for Receiver
Loopbacks and PRBS Pattern Generation/
Detection with Output for Received Errors
Generates/Detects In-Band Loop Codes,
1 to 16 Bits Including CSU Loop Codes
8-Bit Parallel or Serial Interface with
Optional Hardware Mode
Muxed and Nonmuxed Parallel Bus Supports
Intel or Motorola
Detects/Generates Blue (AIS) Alarms
NRZ/Bipolar Interface for Tx/Rx Data I/O
Transmit Open-Circuit Detection
Receive Carrier Loss (RCL) Indication
(G.775)
High-Impedance State for TTIP and TRING
50mA (RMS) Current Limiter
PRELMINARY
44
TOP VIEW
1
DS21348
44 TQFP
DS21Q348
49 CSBGA
(7mm x 7mm)
See Section 8 for 144-pin CSBGA pinout.
ORDERING INFORMATION
PART
CHANNEL
DS21348TN
DS21348TN+
DS21348T
DS21348T+
DS21348GN
DS21348GN+
DS21348G
DS21348G+
DS21Q348N
DS21Q348
Single
Single
Single
Single
Single
Single
Single
Single
Four
Four
TEMP
RANGE
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
0°C to +70°C
PIN-PACKAGE
44 TQFP
44 TQFP
44 TQFP
44 TQFP
49 CSBGA
49 CSBGA
49 CSBGA
49 CSBGA
144 CSBGA
144 CSBGA
+ Denotes lead-free/RoHS-compliant package.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.
1 of 76
REV: 011206
DS21348/DS21Q348
DETAILED DESCRIPTION
The DS21348 is a complete selectable E1 or T1 line interface unit (LIU) for short-haul and long-haul
applications. Throughout the data sheet, J1 is represented wherever T1 exists. Receive sensitivity adjusts
automatically to the incoming signal and can be programmed for 0dB to 12dB or 0dB to 43dB for E1
applications and 0dB to 30dB or 0dB to 36dB for T1 applications. The device can generate the necessary
G.703 E1 waveshapes in 75Ω or 120Ω applications and DSX-1 line build-outs or CSU line build-outs of
0dB, -7.5dB, -15dB, and -22.5dB for T1 applications. The crystal-less on-board jitter attenuator requires
only a 2.048MHz MCLK for both E1 and T1 applications (with the option of using a 1.544MHz MCLK
in T1 applications). The jitter attenuator FIFO is selectable to either 32 bits or 128 bits in depth and can
be placed in either the transmit or receive data paths. An X 2.048MHz output clock synthesized to RCLK
is available for use as a backplane system clock (where n = 1, 2, 4, or 8).
The DS21348 has diagnostic capabilities such as loopbacks and PRBS pattern generation/detection. 16bit loop-up and loop-down codes can be generated and detected. The device can be controlled through an
8-bit parallel muxed or nonmuxed port, serial port, or used in hardware mode. The device fully meets all
of the latest E1 and T1 specifications including ANSI T1.403-1999, ANSI T1.408, AT&T TR 62411,
ITU G.703, G.704, G.706, G.736, G.775, G.823, I.431, O.151, O.161, ETSI ETS 300 166, JTG.703,
JTI.431, JJ-20.1, TBR12, TBR13, and CTR4.
2 of 76
DS21348/DS21Q348
TABLE OF CONTENTS
1.
INTRODUCTION.................................................................................................................. 6
1.1
2.
DOCUMENT REVISION HISTORY...............................................................................................6
PIN DESCRIPTION............................................................................................................ 10
2.1
3.
PIN DESCRIPTIONS ........................................................................................................................14
HARDWARE MODE .......................................................................................................... 25
3.1
3.2
3.3
4.
REGISTER MAP .............................................................................................................................25
PARALLEL PORT OPERATION .........................................................................................................26
SERIAL PORT OPERATION..............................................................................................................26
CONTROL REGISTERS .................................................................................................... 29
4.1
5.
6.
DEVICE POWER-UP AND RESET .....................................................................................................32
STATUS REGISTERS ....................................................................................................... 36
DIAGNOSTICS .................................................................................................................. 41
6.1
6.2
IN-BAND LOOP CODE GENERATION AND DETECTION ......................................................................41
LOOPBACKS ..................................................................................................................................46
6.2.1
6.2.2
6.2.3
6.2.4
6.3
6.4
PRBS GENERATION AND DETECTION ............................................................................................47
ERROR COUNTER ..........................................................................................................................47
6.4.1
6.5
7.
Remote Loopback (RLB) ..................................................................................................................... 46
Local Loopback (LLB) .......................................................................................................................... 46
Analog Loopback (ALB) ....................................................................................................................... 46
Dual Loopback (DLB)........................................................................................................................... 46
Error Counter Update........................................................................................................................... 48
ERROR INSERTION ........................................................................................................................48
ANALOG INTERFACE ...................................................................................................... 49
7.1
7.2
7.3
7.4
8.
9.
10.
11.
12.
RECEIVER .....................................................................................................................................49
TRANSMITTER ...............................................................................................................................50
JITTER ATTENUATOR .....................................................................................................................50
G.703 SYNCHRONIZATION SIGNAL .................................................................................................51
DS21Q348 QUAD LIU ....................................................................................................... 58
DC CHARACTERISTICS ................................................................................................... 62
THERMAL CHARACTERISTICS....................................................................................... 63
AC CHARACTERISTICS ................................................................................................... 64
PACKAGE INFORMATION ............................................................................................... 73
12.1 44-PIN TQFP (56-G4012-001) .....................................................................................................73
12.2 49-BALL CSGBA (7MM X 7MM) (56-G6006-001) ...........................................................................74
12.3 144-BALL CSBGA (17MM X 17MM) (56-G6011-001) .....................................................................75
3 of 76
DS21348/DS21Q348
LIST OF FIGURES
Figure 1-1. DS21348 Block Diagram ..........................................................................................................7
Figure 1-2. Receive Logic...........................................................................................................................8
Figure 1-3. Transmit Logic..........................................................................................................................9
Figure 2-1. Parallel Port Mode Pinout (BIS1 = 0, BIS0 = 1 or 0) (TQFP Package) ..................................22
Figure 2-2. Serial Port Mode Pinout (BIS1 = 1, BIS0 = 0) (TQFP Package) ............................................23
Figure 2-3. Hardware Mode Pinout (BIS1 = 1, BIS0 = 1) (TQFP Package) .............................................24
Figure 3-1. Serial Port Operation for Read Access (R = 1) Mode 1 .........................................................27
Figure 3-2. Serial Port Operation for Read Access Mode 2 .....................................................................27
Figure 3-3. Serial Port Operation for Read Access Mode 3 .....................................................................27
Figure 3-4. Serial Port Operation for Read Access Mode 4 .....................................................................28
Figure 3-5. Serial Port Operation for Write Access (R = 0) Modes 1 and 2..............................................28
Figure 3-6. Serial Port Operation for Write Access (R = 0) Modes 3 and 4..............................................28
Figure 7-1. Basic Interface .......................................................................................................................52
Figure 7-2. Protected Interface Using Internal Receive Termination........................................................53
Figure 7-3. Protected Interface Using External Receive Termination.......................................................54
Figure 7-4. E1 Transmit Pulse Template ..................................................................................................55
Figure 7-5. T1 Transmit Pulse Template ..................................................................................................56
Figure 7-6. Jitter Tolerance ......................................................................................................................57
Figure 7-7. Jitter Attenuation ....................................................................................................................57
Figure 8-1. 144-CSBGA (17mm x 17mm) Pinout .....................................................................................61
Figure 11-1. Intel Bus Read Timing (PBTS = 0, BIS1 = 0, BIS0 = 0) .......................................................65
Figure 11-2. Intel Bus Write Timing (PBTS = 0, BIS1 = 0, BIS0 = 0) .......................................................65
Figure 11-3. Motorola Bus Timing (PBTS = 1, BIS1 = 0, BIS0 = 0)..........................................................66
Figure 11-4. Intel Bus Read Timing (PBTS = 0, BIS1 = 0, BIS0 = 1) .......................................................68
Figure 11-5. Intel Bus Write Timing (PBTS = 0, BIS1 = 0, BIS0 = 1) .......................................................68
Figure 11-6. Motorola Bus Read Timing (PBTS = 1, BIS1 = 0, BIS0 = 1) ................................................69
Figure 11-7. Motorola Bus Write Timing (PBTS = 1, BIS1 = 0, BIS0 = 1) ................................................69
Figure 11-8. Serial Bus Timing (BIS1 = 1, BIS0 = 0) ................................................................................70
Figure 11-9. Receive Side Timing ............................................................................................................71
Figure 11-10. Transmit Side Timing .........................................................................................................72
4 of 76
DS21348/DS21Q348
LIST OF TABLES
Table 2-1. Bus Interface Selection ...........................................................................................................10
Table 2-2. Pin Assignment in Parallel Port Mode .....................................................................................10
Table 2-3. Pin Assignment in Serial Port Mode ........................................................................................11
Table 2-4. Pin Assignment in Hardware Mode .........................................................................................12
Table 2-5. Pin Descriptions in Parallel Port Mode (Sorted by Pin Name, DS21348T Pin Numbering).....14
Table 2-6. Pin Descriptions in Serial Port Mode (Sorted By Pin Name, DS21348T Pin Numbering) .......16
Table 2-7. Pin Descriptions in Hardware Mode (Sorted By Pin Name, DS21348T Pin Numbering) ........18
Table 2-8. Loopback Control in Hardware Mode ......................................................................................21
Table 2-9. Transmit Data Control in Hardware Mode ...............................................................................21
Table 2-10. Receive Sensitivity Settings ..................................................................................................21
Table 2-11. Monitor Gain Settings ............................................................................................................21
Table 2-12. Internal Rx Termination Select ..............................................................................................21
Table 2-13. MCLK Selection.....................................................................................................................22
Table 3-1. Register Map ...........................................................................................................................25
Table 4-1. MCLK Selection.......................................................................................................................30
Table 4-2. Receive Equalizer Sensitivity Settings ....................................................................................32
Table 4-3. Backplane Clock Select...........................................................................................................34
Table 4-4. Monitor Gain Settings ..............................................................................................................34
Table 4-5. Internal Rx Termination Select ................................................................................................34
Table 5-1. Received Alarm Criteria ..........................................................................................................36
Table 5-2. Receive Level Indication .........................................................................................................40
Table 6-1. Transmit Code Length .............................................................................................................41
Table 6-2. Receive Code Length..............................................................................................................42
Table 6-3. Definition of Received Errors...................................................................................................47
Table 6-4. Function of ECRS Bits and RNEG Pin ....................................................................................48
Table 7-1. Line Build-Out Select for E1 in Register CCR4 (ETS = 0).......................................................51
Table 7-2. Line Build-Out Select for T1 in Register CCR4 (ETS = 1).......................................................51
Table 7-3. Transformer Specifications for 3.3V Operation .......................................................................51
Table 8-1. DS21Q348 Pin Assignment.....................................................................................................58
Table 9-1. Recommended DC Operating Conditions ...............................................................................62
Table 9-2. Capacitance ............................................................................................................................62
Table 9-3. DC Characteristics ..................................................................................................................62
Table 10-1. Thermal Characteristics—DS21Q348 CSBGA Package.......................................................63
Table 10-2. Theta-JA (θJA) vs. Airflow.......................................................................................................63
Table 11-1. AC Characteristics—Multiplexed Parallel Port (BIS1 = 0, BIS0 = 0) .....................................64
Table 11-2. AC Characteristics—Nonmultiplexed Parallel Port (BIS1 = 0, BIS0 = 1)...............................67
Table 11-3. AC Characteristics—Serial Port (BIS1 = 1, BIS0 = 0) ...........................................................70
Table 11-4. AC Characteristics—Receive Side ........................................................................................71
Table 11-5. AC Characteristics—Transmit Side .......................................................................................72
5 of 76
DS21348/DS21Q348
1. INTRODUCTION
The analog AMI/HDB3 waveform off of the E1 line or the AMI/B8ZS waveform off of the T1 line is
transformer coupled into the RTIP and RRING pins of the DS21348. The user has the option to use
internal termination, software selectable for 75Ω/100Ω/120Ω applications, or external termination. The
device recovers clock and data from the analog signal and passes it through the jitter attenuation MUX
outputting the received line clock at RCLK and bipolar or NRZ data at RPOS and RNEG. The DS21348
contains an active filter that reconstructs the analog received signal for the nonlinear losses that occur in
transmission. The receive circuitry is also configurable for various monitor applications. The device has a
usable receive sensitivity of 0dB to -43dB for E1 and 0dB to -36dB for T1, which allows the device to
operate on 0.63mm (22AWG) cables up to 2.5km (E1) and 6k feet (T1) in length. Data input at TPOS and
TNEG is sent via the jitter attenuation mux to the waveshaping circuitry and line driver. The DS21348
will drive the E1 or T1 line from the TTIP and TRING pins via a coupling transformer. The line driver
can handle both CEPT 30/ISDN-PRI lines for E1 and long-haul (CSU) or short-haul (DSX-1) lines for
T1.
1.1 Document Revision History
REVISION
011801
092101
101104
113004
011206
DESCRIPTION
Data sheet revised for 3.3V only.
Added supply current measurements
Added thermal characteristics of quad package
Corrected typos and removed all instances of 5V operation.
Updated the storage and soldering temperature specs in the Absolute
Maximum Ratings section.
Added lead-free packages to Ordering Information table on page 1.
6 of 76
DS21348/DS21Q348
MCLK
VSM
VDD
VSS
Figure 1-1. DS21348 Block Diagram
2
2
JACLK
Jitter
Attenuator
MUX
Power Connections
2.048MHz to
1.544MHz PLL
M
U
X
See Figure 1-3
Control and
Interrupt
Control and Test Port
(routed to all blocks)
A0 to A4
Hardware
Interface
21
7 of 76
INT
8
CS
5
D0 to D7 /
AD0 to AD7
ALE(AS)
RD(DS)
WR(R/W)
Parallel Interface
PBTS
SDO
SDI
SCLK
RPOS
RCLK
RNEG
RCL/LOTC
TPOS
TCLK
TNEG
DS21348
Serial Interface
BPCLK
PBEO
MUX
MUX (the Serial, Parallel, and Hardware Interfaces share device pins)
BIS0
See Figure 3-2
Remote Loopback
Jitter Attenuation
(can be placed in either transmit or receive path)
Local Loopback
Remote Loopback (Dual Mode)
Wave Shaping
TTIP
CSU Filters
Line Drivers
Unframed
All Ones
Insertion
TRING
BIS1
Clock / Data
Recovery
Peak Detect
Analog Loopback
RTIP
Filter
RRING
Optional
Termination
VCO / PLL
16.384MHz or
8.192MHz or
4.096MHz or
2.048MHz
Synthesizer
HRST
TEST
DS21348/DS21Q348
Figure 1-2. Receive Logic
Clock
Invert
From
Remote
Loopback
Routed to
All Blocks
RCLK
CCR2.0
RPOS
mux
B8ZS/HDB3
Decoder
NRZ Data
RNEG
BPV/CV/EXZ
CCR1.6
4 or 8 Zero Detect
16 Zero Detect
CCR2.3
CCR6.2/ RIR1.5
CCR6.0/
CCR6.1
All Ones
Detector
SR.4 RIR1.3
RIR1.7
Loop Code
Detector
SR.6
SR.7
PBEO
PRBS
Detector
SR.0
mux
CCR6.0
RIR1.6
CCR1.4
8 of 76
16-Bit Error
Counter (ECR)
rx bd
DS21348/DS21Q348
Figure 1-3. Transmit Logic
CCR3.3
CCR1.6
CCR3.4
CCR2.2
CCR3.1
PRBS Generator
CCR3.0
OR
Gate
mux
1
To
Remote
Loopback
BPV
Insert
B8ZS/
HDB3
Coder
Loop Code Generator
Logic
Error
Insert
TPOS
OR
Gate
TNEG
mux
0
0
0
Clock
Invert
mux
Routed to
All Blocks
JACLK
(derived
from
MCLK)
1
mux
1
RCLK
OR
Gate
CCR2.1
AND
Gate
CCR1.1
Loss Of Transmit
Clock Detect
CCR1.2
CCR1.0
tx bd
To LOTC Output Pin
9 of 76
SR.5
TCLK
DS21348/DS21Q348
2. PIN DESCRIPTION
The DS21348 can be controlled in a parallel port mode, serial port mode, or hardware mode (Table 2-2,
Table 2-3, and Table 2-4).
Table 2-1. Bus Interface Selection
BIS1
0
0
0
0
1
1
BIS0
0
0
1
1
0
1
PBTS
0
1
0
1
—
—
MODE
Muxed Intel
Muxed Motorola
Nonmuxed Intel
Nonmuxed Motorola
Serial Port
Hardware
Table 2-2. Pin Assignment in Parallel Port Mode
PIN
DS21348T
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
DS21348G
C3
C2
B1
D2
C1
D3
D1
E1
F2
F1
G1
E3
F3
G2
F4
G3
E4
G4
F5
G5
F6
G6
E5
E6
F7
D6
D5
I/O
I
I
I
I
I
I
I/O
I
I
I
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
—
—
I/O
O
O
I
I
PARALLEL
PORT MODE
CS
RD (DS)
WR (R/W)
ALE (AS)
NA
NA
A4
A3
A2
A1
A0
D7/AD7
D6/AD6
D5/AD5
D4/AD4
D3/AD3
D2/AD2
D1/AD1
D0/AD0
VSM
VDD
VSS
INT
PBEO
RCL/LOTC
TEST
RTIP
10 of 76
DS21348/DS21Q348
PIN
DS21348T
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
DS21348G
D7
C6
C7
B6
B7
A7
C5
B5
A6
B4
C4
A4
B3
A3
B2
A2
A1
I/O
I
I
I
O
I
I
O
—
—
O
O
O
O
I
I
I
I
PARALLEL
PORT MODE
RRING
HRST
MCLK
BPCLK
BIS0
BIS1
TTIP
VSS
VDD
TRING
RPOS
RNEG
RCLK
TPOS
TNEG
TCLK
PBTS
Table 2-3. Pin Assignment in Serial Port Mode
PIN
DS21348T
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
DS21348G
C3
C2
B1
D2
C1
D3
D1
E1
F2
F1
G1
E3
F3
G2
F4
G3
E4
G4
F5
G5
F6
G6
I/O
I
I
I
I
I
I
I/O
I
I
I
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
—
—
SERIAL
PORT MODE
CS
NA
NA
NA
SCLK
SDI
SDO
ICES
OCES
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
VSM
VDD
VSS
11 of 76
DS21348/DS21Q348
PIN
DS21348T
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
DS21348G
E5
E6
F7
D6
D5
D7
C6
C7
B6
B7
A7
C5
B5
A6
B4
C4
A4
B3
A3
B2
A2
A1
I/O
I/O
O
O
I
I
I
I
I
O
I
I
O
—
—
O
O
O
O
I
I
I
I
SERIAL
PORT MODE
INT
PBEO
RCL/LOTC
TEST
RTIP
RRING
HRST
MCLK
BPCLK
BIS0
BIS1
TTIP
VSS
VDD
TRING
RPOS
RNEG
RCLK
TPOS
TNEG
TCLK
NA
Table 2-4. Pin Assignment in Hardware Mode
PIN
DS21348T
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DS21348G
C3
C2
B1
D2
C1
D3
D1
E1
F2
F1
G1
E3
F3
G2
F4
G3
I/O
I
I
I
I
I
I
I/O
I
I
I
I
I/O
I/O
I/O
I/O
I/O
HARDWARE
MODE
EGL
ETS
NRZE
SCLKE
L2
L1
L0
DJA
JAMUX
JAS
HBE
CES
TPD
TX0
TX1
LOOP0
12 of 76
DS21348/DS21Q348
PIN
DS21348T
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
DS21348G
E4
G4
F5
G5
F6
G6
E5
E6
F7
D6
D5
D7
C6
C7
B6
B7
A7
C5
B5
A6
B4
C4
A4
B3
A3
B2
A2
A1
I/O
I/O
I/O
I/O
I
—
—
I/O
O
O
I
I
I
I
I
O
I
I
O
—
—
O
O
O
O
I
I
I
I
HARDWARE
MODE
LOOP1
MM0
MM1
VSM
VDD
VSS
RT1
PBEO
RCL
TEST
RTIP
RRING
HRST
MCLK
BPCLK
BIS0
BIS1
TTIP
VSS
VDD
TRING
RPOS
RNEG
RCLK
TPOS
TNEG
TCLK
RT0
13 of 76
DS21348/DS21Q348
2.1 Pin Descriptions
Table 2-5. Pin Descriptions in Parallel Port Mode (Sorted by Pin Name,
DS21348T Pin Numbering)
NAME
PIN
I/O
A0 to A4
11 to 7
I
ALE (AS)
4
I
BIS0/BIS1
32/33
I
BPCLK
31
O
CS
1
I
D0/AD0 to
D7/AD7
19 to 12
I/O
HRST
29
I
INT
23
O
MCLK
30
I
N/A
—
I
PBEO
24
O
FUNCTION
Address Bus. In nonmultiplexed bus operation (BIS1 = 0, BIS0 =
1), serves as the address bus. In multiplexed bus operation (BIS1 =
0, BIS0 = 0), these pins are not used and should be tied low.
Address Latch Enable (Address Strobe). When using the parallel
port (BIS1 = 0) in multiplexed bus mode (BIS0 = 0), serves to
demultiplex the bus on a positive-going edge. In nonmultiplexed bus
mode (BIS0 = 1), should be tied low.
Bus Interface Select Bits 0 and 1. Used to select bus interface
option. See Table 2-1 for details.
Backplane Clock. A 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz clock output that is referenced to RCLK selectable via
CCR5.7 and CCR5.6. In hardware mode, defaults to 16.384MHz
output.
Chip Select, Active Low. This active-low signal must be low to
read or write to the device.
Data Bus/Address/Data Bus. In nonmultiplexed bus operation
(BIS1 = 0, BIS0 = 1), serves as the data bus. In multiplexed bus
operation (BIS1 = 0, BIS0 = 0), serves as an 8-bit multiplexed
address/data bus.
Hardware Reset, Active Low. Bringing HRST low resets the
DS21348, setting all control bits to their default state of all zeros.
Interrupt, Active Low. Flags host controller during conditions and
change of conditions defined in the Status Register. Active low,
open drain output.
Master Clock. A 2.048MHz (±50ppm) clock source with TTL
levels is applied at this pin. This clock is used internally for both
clock/data recovery and for jitter attenuation. Use of a T1 1.544MHz
clock source is optional.
Not Assigned. Should be tied low.
PRBS Bit Error Output. The receiver will constantly search for a
215-1 or a 220-1 PRBS depending on the ETS bit setting (CCR1.7).
Remains high if out of synchronization with the PRBS pattern. Goes
low when synchronized to the PRBS pattern. Any errors in the
received pattern after synchronization will cause a positive going
pulse (with same period as E1 or T1 clock) synchronous with
RCLK. PRBS bit errors can also be reported to the ECR1 and ECR2
registers by setting CCR6.2 to a logic 1.
14 of 76
DS21348/DS21Q348
NAME
PIN
I/O
PBTS
44
I
RCLK
40
O
RD (DS)
2
I
RCL/
LOTC
25
O
RNEG
39
O
RPOS
38
O
RTIP/
RRING
27/28
I
TCLK
43
I
TEST
26
I
TNEG
42
I
TPOS
41
I
FUNCTION
Parallel Bus Type Select. When using the parallel port (BIS1 = 0),
set high to select Motorola bus timing, set low to select Intel bus
timing. This pin controls the function of the RD (DS), ALE (AS),
and WR (R/W) pins. If PBTS = 1 and BIS1 = 0, then these pins
assume the Motorola function listed in parentheses (). In serial port
mode, this pin should be tied low.
Receive Clock. Buffered recovered clock from the line.
Synchronous to MCLK in absence of signal at RTIP and RRING.
Read Input (Data Strobe), Active Low. DS is active low when in
nonmultiplexed, Motorola mode. See the bus timing diagrams in
Section 11.
Receive Carrier Loss/Loss of Transmit Clock. An output which
will toggle high during a receive carrier loss (CCR2.7 = 0) or will
toggle high if the TCLK pin has not been toggled for 5 µsec ± 2
µsec (CCR2.7 = 1). CCR2.7 defaults to logic 0 when in hardware
mode.
Receive Negative Data. Updated on the rising edge (CCR2.0 = 0)
or the falling edge (CCR2.0 = 1) of RCLK with the bipolar data out
of the line interface. Set NRZE (CCR1.6) to a one for NRZ
applications. In NRZ mode, data will be output on RPOS while a
received error will cause a positive-going pulse synchronous with
RCLK at RNEG. See Section 6.4 for details.
Receive Positive Data. Updated on the rising edge (CCR2.0 = 0) or
the falling edge (CCR2.0 = 1) of RCLK with bipolar data out of the
line interface. Set NRZE (CCR1.6) to a one for NRZ applications. In
NRZ mode, data will be output on RPOS while a received error will
cause a positive-going pulse synchronous with RCLK at RNEG. See
Section 6.4 for details.
Receive Tip and Ring. Analog inputs for clock recovery circuitry.
These pins connect via a 1:1 transformer to the line. See Section 5
for details.
Transmit Clock. A 2.048MHz or 1.544MHz primary clock. Used to
clock data through the transmit side formatter. Can be sourced
internally by MCLK or RCLK. See Common Control Register 1 and
Figure 1-3.
Tri-State Control. Set high to tri-state all outputs and I/O pins
(including the parallel control port). Set low for normal operation.
Useful in board level testing.
Transmit Negative Data. Sampled on the falling edge (CCR2.1 =
0) or the rising edge (CCR2.1 = 1) of TCLK for data to be
transmitted out onto the line.
Transmit Positive Data. Sampled on the falling edge (CCR2.1 = 0)
or the rising edge (CCR2.1 = 1) of TCLK for data to be transmitted
out onto the line.
15 of 76
DS21348/DS21Q348
NAME
PIN
I/O
TTIP/
TRING
34/37
O
VDD
VSM
VSS
21/36
20
22/35
—
I
—
WR (R/W)
3
I
FUNCTION
Transmit Tip and Ring [TTIP AND TRING]. Analog line driver
outputs. These pins connect via a step-up transformer to the line. See
Section 5 for details.
Positive Supply. 3.3V ±5%
Voltage Supply Mode. Should be low for 3.3V operation.
Signal Ground
Write Input (Read/Write), Active Low. See the bus timing
diagrams in Section 11.
Table 2-6. Pin Descriptions in Serial Port Mode (Sorted By Pin Name,
DS21348T Pin Numbering)
NAME
PIN
I/O
BIS0/BIS1
32/33
I
BPCLK
31
O
CS
1
I
HRST
29
I
ICES
8
I
INT
23
O
MCLK
30
I
NA
—
I
OCES
9
I
PBEO
24
O
FUNCTION
Bus Interface Select Bits 0 and 1. Used to select bus interface
option. See Table 2-1 for details.
Backplane Clock. A 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz clock output that is referenced to RCLK selectable via
CCR5.7 and CCR5.6. In hardware mode, defaults to 16.384MHz
output.
Chip Select, Active Low. Active-low signal must be low to read or
write to the device.
Hardware Reset, Active Low. Bringing HRST low will reset the
DS21348 setting all control bits to their default state of all zeros.
Input Clock Edge Select. Selects whether the serial port data input
(SDI) is sampled on rising (ICES =0) or falling edge (ICES = 1) of
SCLK.
Interrupt, Active Low. Flags host controller during conditions and
change of conditions defined in the Status Register. Active-low,
open-drain output.
Master Clock. A 2.048MHz (±50ppm) clock source with TTL
levels is applied at this pin. This clock is used internally for both
clock/data recovery and for jitter attenuation. Use of a T1 1.544MHz
clock source is optional.
Not Assigned. Should be tied low.
Output Clock Edge Select. Selects whether the serial port data
output (SDO) is valid on the rising (OCES = 1) or falling edge
(OCES = 0) of SCLK.
PRBS Bit Error Output. The receiver will constantly search for a
215-1 or a 220-1 PRBS depending on the ETS bit setting (CCR1.7).
Remains high if out of synchronization with the PRBS pattern. Goes
low when synchronized to the PRBS pattern. Any errors in the
received pattern after synchronization will cause a positive going
pulse (with same period as E1 or T1 clock) synchronous with
RCLK. PRBS bit errors can also be reported to the ECR1 and ECR2
registers by setting CCR6.2 to a logic 1.
16 of 76
DS21348/DS21Q348
NAME
PIN
I/O
RCLK
40
O
RCL/LOTC
25
O
RNEG
39
O
RPOS
38
O
RTIP/
RRING
27/28
I
SCLK
5
I
SDI
6
I
SDO
7
O
TCLK
43
I
TEST
26
I
TNEG
42
I
TPOS
41
I
TTIP/TRIN
G
34/37
O
VDD
VSM
VSS
21/36
20
22/35
—
I
—
FUNCTION
Receive Clock. Buffered recovered clock from the line.
Synchronous to MCLK in absence of signal at RTIP and RRING.
Receive Carrier Loss/Loss of Transmit Clock. An output which
will toggle high during a receive carrier loss (CCR2.7 = 0) or will
toggle high if the TCLK pin has not been toggled for 5µs ± 2µs
(CCR2.7 = 1). CCR2.7 defaults to logic 0 when in hardware mode.
Receive Negative Data. Updated on the rising edge (CCR2.0 = 0)
or the falling edge (CCR2.0 = 1) of RCLK with the bipolar data out
of the line interface. Set NRZE (CCR1.6) to a one for NRZ
applications. In NRZ mode, data will be output on RPOS while a
received error will cause a positive-going pulse synchronous with
RCLK at RNEG. See Section 6.4 for details.
Receive Positive Data. Updated on the rising edge (CCR2.0 = 0) or
the falling edge (CCR2.0 = 1) of RCLK with bipolar data out of the
line interface. Set NRZE (CCR1.6) to a one for NRZ applications. In
NRZ mode, data will be output on RPOS while a received error will
cause a positive-going pulse synchronous with RCLK at RNEG. See
Section 6.4 for details.
Receive Tip and Ring. Analog inputs for clock recovery circuitry.
These pins connect via a 1:1 transformer to the line. See Section 5
for details.
Serial Clock. Serial bus clock input.
Serial Data Input. Sampled on rising edge (ICES = 0) or the falling
edge (ICES = 1) of SCLK.
Serial Data Output. Valid on the falling edge (OCES = 0) or the
rising edge (OCES = 1) of SCLK.
Transmit Clock. A 2.048MHz or 1.544MHz primary clock. Used to
clock data through the transmit side formatter. Can be sourced
internally by MCLK or RCLK. See Common Control Register 1 and
Figure 1-3.
Tri-State Control. Set high to tri-state all outputs and I/O pins
(including the parallel control port). Set low for normal operation.
Useful in board-level testing.
Transmit Negative Data. Sampled on the falling edge (CCR2.1 =
0) or the rising edge (CCR2.1 = 1) of TCLK for data to be
transmitted out onto the line.
Transmit Positive Data. Sampled on the falling edge (CCR2.1 = 0)
or the rising edge (CCR2.1 = 1) of TCLK for data to be transmitted
out onto the line.
Transmit Tip and Ring [TTIP and TRING]. Analog line-driver
outputs. These pins connect via a step-up transformer to the line.
See Section 5 for details.
Positive Supply. 3.3V ±5%
Voltage Supply Mode. Should be tied low for 3.3V operation.
Signal Ground
17 of 76
DS21348/DS21Q348
Table 2-7. Pin Descriptions in Hardware Mode (Sorted By Pin Name,
DS21348T Pin Numbering)
NAME
PIN
I/O
BIS0/BIS1
32/33
I
BPCLK
31
O
CES
12
I
DJA
8
I
EGL
1
I
ETS
2
I
HBE
11
I
HRST
29
I
JAMUX
9
I
JAS
10
I
L0/L1/L2
7/6/5
I
LOOP0/
LOOP1
16/17
I
FUNCTION
Bus Interface Select Bits 0 and 1. Used to select bus interface
option. BIS0 = 1 and BIS1 = 1 selects hardware mode.
Backplane Clock. 16.384MHz output.
Receive and Transmit Clock Edge Select. Selects which RCLK
edge to update RPOS and RNEG and which TCLK edge to sample
TPOS and TNEG.
0 = update RNEG/RPOS on rising edge of RCLK; sample
TPOS/TNEG on falling edge of TCLK
1 = update RNEG/RPOS on falling edge of RCLK; sample
TPOS/TNEG on rising edge of TCLK
Disable Jitter Attenuator.
0 = jitter attenuator enabled
1 = jitter attenuator disabled
Receive Equalizer Gain Limit. This pin controls the sensitivity of
the receive equalizer.
EGL E1 (ETS = 0)
0 = -12dB (short haul)
1 = -43dB (long haul)
EGL T1 (ETS = 1)
0 = -36dB (long haul)
1 = -30dB (limited long haul)
E1/T1 Select.
0 = E1
1 = T1
Receive and Transmit HDB3/B8ZS Enable
0 = enable HDB3 (E1)/B8ZS (T1)
1 = disable HDB3 (E1)/B8ZS (T1)
Hardware Reset. Bringing HRST low will reset the DS21348.
Jitter Attenuator Mux. Controls the source for JACLK.
See Figure 1-1 and Table 2-13.
E1 (ETS = 0)
JAMUX
MCLK = 2.048MHz
0
T1 (ETS = 1)
MCLK = 2.048MHz
1
MCLK = 1.544MHz
0
Jitter Attenuator Select
0 = place the jitter attenuator on the receive side
1 = place the jitter attenuator on the transmit side
Transmit LIU Waveshape Select Bits 0 and 1 [H/W Mode].
These inputs determine the waveshape of the transmitter (Table 7-1
and Table 7-2.
Loopback Select Bits 0 and 1 [H/W Mode]. These inputs
determine the active loopback mode (if any). See Table 2-8.
18 of 76
DS21348/DS21Q348
NAME
PIN
I/O
MCLK
30
I
MM0/MM1
18/19
I
NA
—
I
NRZE
3
I
PBEO
24
O
RCLK
40
O
RCL
25
O
RNEG
39
O
RPOS
38
O
RT0/RT1
44/23
I
RTIP/
RRING
27/28
I
SCLKE
4
I
TCLK
43
I
FUNCTION
Master Clock. A 2.048MHz (±50ppm) clock source with TTL
levels is applied at this pin. This clock is used internally for both
clock/data recovery and for jitter attenuation. Use of a T1 1.544MHz
clock source is optional. G.703 requires an accuracy of ±50ppm for
both T1 and E1. TR62411 and ANSI specs require an accuracy of
±32ppm for T1 interfaces.
Monitor Mode Select Bits 0 and 1 [H/W Mode]. These inputs
determine if the receive equalizer is in a monitor mode (Table 2-11).
Not Assigned. Should be tied low.
NRZ Enable [H/W Mode]
0 = Bipolar data at RPOS/RNEG and TPOS/TNEG
1 = NRZ data at RPOS and TPOS or TNEG; RNEG outputs a
positive going pulse when device receives a BPV, CV, or EXZ.
PRBS Bit Error Output. The receiver will constantly search for a
QRSS (T1) or a 215-1 (E1) PRBS depending whether T1 or E1
mode is selected. Remains high if out of synchronization with the
PRBS pattern. Goes low when synchronized to the PRBS pattern.
Any errors in the received pattern after synchronization will cause a
positive going pulse (with same period as E1 or T1 clock)
synchronous with RCLK.
Receive Clock. Buffered recovered clock from the line.
Synchronous to MCLK in absence of signal at RTIP and RRING.
Receive Carrier Loss. An output which will toggle high during a
receive carrier loss.
Receive Negative Data. Updated on the rising edge (CES = 0) or
the falling edge (CES = 1) of RCLK with the bipolar data out of the
line interface. Set NRZE to a one for NRZ applications. In NRZ
mode, data will be output on RPOS while a received error will cause
a positive-going pulse synchronous with RCLK at RNEG. See
Section 6.4 for details.
Receive Positive Data. Updated on the rising edge (CES = 0) or the
falling edge (CES = 1) of RCLK with bipolar data out of the line
interface. Set NRZE pin to a one for NRZ applications. In NRZ
mode, data will be output on RPOS while a received error will cause
a positive-going pulse synchronous with RCLK at RNEG. See
section 6.4 for details.
Receive LIU Termination Select Bits 0 and 1 [H/W Mode]. These
inputs determine the receive termination. See Table 2-12.
Receive Tip and Ring. Analog inputs for clock recovery circuitry.
These pins connect via a 1:1 transformer to the line. See Section 5
for details.
Receive and Transmit Synchronization Clock Enable
0 = disable 2.048MHz synchronization transmit and receive mode
1 = enable 2.048 Hz synchronization transmit and receive mode
Transmit Clock. A 2.048MHz or 1.544MHz primary clock. Used to
clock data through the transmit side formatter.
19 of 76
DS21348/DS21Q348
NAME
PIN
I/O
TEST
26
I
TNEG
42
I
TPD
13
I
TPOS
41
I
TTIP/TRING
34/37
O
TX0/TX1
14/15
I
VDD
VSM
VSS
21/36
20
22/35
—
I
—
FUNCTION
Tri-State Control. Set high to tri-state all outputs and I/O pins
(including the parallel control port). Set low for normal operation.
Useful in board-level testing.
Transmit Negative Data. Sampled on the falling edge (CES = 0) or
the rising edge (CES = 1) of TCLK for data to be transmitted out
onto the line.
Transmit Power-Down
0 = normal transmitter operation
1 = powers down the transmitter and tri-states the TTIP and TRING
pins
Transmit Positive Data. Sampled on the falling edge (CES = 0) or
the rising edge (CES = 1) of TCLK for data to be transmitted out
onto the line.
Transmit Tip and Ring [TTIP and TRING]. Analog line driver
outputs. These pins connect via a step-up transformer to the line.
See Section 5 for details.
Transmit Data Source Select Bits 0 and 1 [H/W Mode]. These
inputs determine the source of the transmit data. See Table 2-9.
Positive Supply. 3.3V ±5%
Voltage Supply Mode. Should be tied low for 3.3V operation.
Signal Ground
Note: G.703 requires an accuracy of ±50ppm for both T1 and E1. TR62411 and ANSI specs require an accuracy of ±32ppm for
T1 interfaces.
20 of 76
DS21348/DS21Q348
Table 2-8. Loopback Control in Hardware Mode
LOOPBACK
SYMBOL
Remote Loopback
Local Loopback
Analog Loopback
No Loopback
RLB
LLB
ALB
—
CONTROL
BIT
CCR6.6
CCR6.7
CCR6.4
—
LOOP1
LOOP0
1
1
0
0
1
0
1
0
Table 2-9. Transmit Data Control in Hardware Mode
TRANSMIT DATA
Transmit Unframed
All Ones
Transmit Alternating
Ones and Zeros
Transmit PRBS
TPOS and TNEG
SYMBOL
CONTROL
BIT
TX1
TX0
TUA1
CCR3.7
1
1
TAOZ
CCR3.5
1
0
TPRBSE
—
CCR3.4
—
0
0
1
0
Table 2-10. Receive Sensitivity Settings
EGL
(CCR4.4)
0
1
1
0
ETS
(CCR1.7)
0 (E1)
0 (E1)
1 (T1)
1 (T1)
RECEIVE SENSITIVITY
-12dB (short haul)
-43dB (long haul)
-30dB (limited long haul)
-36dB (long haul)
Table 2-11. Monitor Gain Settings
MM1
(CCR5.5)
0
0
1
1
MM0
(CCR5.4)
0
1
0
1
INTERNAL LINEAR
GAIN BOOST (dB)
Normal operation (no boost)
20
26
32
Table 2-12. Internal Rx Termination Select
RT1
(CCR5.1)
0
0
1
1
RT0
(CCR5.0)
0
1
0
1
INTERNAL RECEIVE
TERMINATION CONFIGURATION
Internal receive-side termination disabled
Internal receive-side 120Ω enabled
Internal receive-side 100Ω enabled
Internal receive-side 75Ω enabled
21 of 76
DS21348/DS21Q348
Table 2-13. MCLK Selection
MCLK
(MHz)
2.048
2.048
1.544
JAMUX
(CCR1.3)
0
1
0
ETS
(CCR1.7)
0
1
1
Figure 2-1. Parallel Port Mode Pinout (BIS1 = 0, BIS0 = 1 or 0) (TQFP
Package)
34 TTIP
35 VSS
36 VDD
37 TRING
38 RPOS
39 RNEG
40 RCLK
41 TPOS
42 TNEG
43 TCLK
44 PBTS
1 CS
BIS1 33 tie low
2 RD (DS)
BIS0 32 TIE LOW (MUX) OR HIGH (NONMUX)
3 WR (R/W)
BPCLK 31
4 ALE (AS)
MCLK 30
DS21348
Parallel Port
Operation
5 NA
6 NA
7 A4
HRST 29
RRING 28
RTIP 27
(NOTE: TIE ALL NA PINS LOW)
8 A3
TEST 26
9 A2
RCL/LOTC 25
10 A1
PBEO 24
INT 23
VSS 22
TIE LOW
22 of 76
VDD 21
VSM 20
AD0/D0 19
AD1/D1 18
AD2/D2 17
AD3/D3 16
AD4/D4 15
AD5/D5 14
AD6/D6 13
AD7/D7 12
11 A0
DS21348/DS21Q348
Figure 2-2. Serial Port Mode Pinout (BIS1 = 1, BIS0 = 0) (TQFP Package)
TIE LOW
35 VSS
36 VDD
37 TRING
38 RPOS
39 RNEG
40 RCLK
41 TPOS
42 TNEG
43 TCLK
44 PBTS
1 CS
34
TT
IP
BIS1 33 TIE HIGH
BIS0 32 TIE LOW
2 NA
3 NA
BPCLK 31
4 NA
MCLK 30
DS21348
Serial Port
Operation
5 SCLK
6 SDI
7 SDO
HRST 29
RRING 28
RTIP 27
(NOTE: TIE ALL NA PINS LOW)
8 ICES
TEST 26
9 OCES
RCL/LOTC 25
10 NA
PBEO 24
11 NA
INT 23
VSS 22
VDD 21
VSM 20
NA 19
NA 18
NA 17
NA 16
NA 15
NA 14
NA 13
NA 12
TIE LOW
23 of 76
DS21348/DS21Q348
Figure 2-3. Hardware Mode Pinout (BIS1 = 1, BIS0 = 1) (TQFP Package)
34 TTIP
35 VSS
36 VDD
37 TRING
38 RPOS
39 RNEG
40 RCLK
41 TPOS
42 TNEG
43 TCLK
44 RT0
1 EGL
BIS1 33
TIE HIGH
2 ETS
BIS0 32
TIE HIGH
3 NRZE
BPCLK 31
MCLK 30
4 SCLKE
DS21348
Hardware
Operation
5 L2
6 L1
HRST 29
RRING 28
7 L0
RTIP 27
8 DJA
TEST 26
RCL 25
9 JAMUX
11 HBE
RT1 23
VSS 22
TIE LOW
24 of 76
VDD 21
VSM 20
MM1 19
MM0 18
TX1 15
TX0 14
TPD 13
CES 12
LOOP1 17
PBEO 24
LOOP0 16
10 JAS
DS21348/DS21Q348
3. HARDWARE MODE
In hardware mode (BIS1 = 1, BIS0 = 1), pins 1–19, 23, 25, 31, and 44 are redefined to be used for
initializing the DS21348. BPCLK (pin 31) defaults to a 16.384MHz output when in hardware mode. The
RCL/LOTC (pin 25) is designated to RCL when in hardware mode. JABDS (CCR4.2) defaults to logic 0.
The RHBE (CCR2.3) and THBE (CCR2.2) control bits are combined and controlled by HBE at pin 11
while the RSCLKE (CCR5.3) and TSCLKE (CCR5.2) bits are combined and controlled by SCLKE at
pin 4. TCES (CCR2.1) and RCES (CCR2.0) are combined and controlled by CES at pin 12. The
transmitter functions are combined and controlled by TX1 (pin 15) and TX0 (pin 14). The loopback
functions are controlled by LOOP1 (pin 17) and LOOP0 (pin 16). All other control bits default to the
logic 0 setting.
3.1 Register Map
Table 3-1. Register Map
NAME
REGISTER
CCR1
CCR2
CCR3
CCR4
CCR5
CCR6
SR
IMR
RIR1
RIR2
IBCC
TCD1
TCD2
RUPCD1
RUPCD2
RDNCD1
RDNCD2
ECR1
ECR2
TEST1
TEST2
TEST3
—
Common Control Register 1
Common Control Register 2
Common Control Register 3
Common Control Register 4
Common Control Register 5
Common Control Register 6
Status Register
Interrupt Mask Register
Receive Information Register 1
Receive Information Register 2
In-Band Code Control Register
Transmit Code Definition Register 1
Transmit Code Definition Register 2
Receive Up Code Definition Register 1
Receive Up Code Definition Register 2
Receive Down Code Definition Register 1
Receive Down Code Definition Register 2
Error Count Register 1
Error Count Register 2
Test 1
Test 2
Test 3
—
R/W
PARALLEL
PORT MODE
R/W
R/W
R/W
R/W
R/W
R/W
R
R/W
R
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
R
R/W
R/W
R/W
—
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
(Note 1)
SERIAL PORT
MODE
(Notes 2 to 5)
(msb)
(lsb)
B000 000A
B000 001A
B000 010A
B000 011A
B000 100A
B000 101A
B000 110A
B000 111A
B001 000A
B001 001A
B001 010A
B001 011A
B001 100A
B001 101A
B001 110A
B001 111A
B010 000A
B010 001A
B010 010A
B010 011A
B010 100A
B010 101A
—
Note 1:
Register addresses 16h to 1Fh do not exist.
Note 2:
In the Serial Port Mode, the LSB is on the right hand side.
Note 3:
In the Serial Port Mode, data is read and written LSB first.
Note 4:
In the Serial Port Mode, the A bit (the LSB) determines whether the access is a read (A = 1) or a write (A = 0).
Note 5:
In the Serial Port Mode, the B bit (the MSB) determines whether the access is a burst access (B = 1) or a single register
access (B = 0).
25 of 76
DS21348/DS21Q348
3.2 Parallel Port Operation
When using the parallel interface on the DS21348 (BIS1 = 0) the user has the option for either
multiplexed bus operation (BIS1 = 0, BIS0 = 0) or non-multiplexed bus operation (BIS1 = 0, BIS0 = 1).
The DS21348 can operate with either Intel or Motorola bus timing configurations. If the PBTS pin is tied
low, Intel timing will be selected; if tied high, Motorola timing will be selected. All Motorola bus signals
are listed in parentheses (). See the timing diagrams in Section 11 for more details.
3.3 Serial Port Operation
Setting BIS1 = 1 and BIS0 = 0 enables the serial bus interface on the DS21348. Port read/write timing is
unrelated to the system transmit and receive timing, allowing asynchronous reads or writes by the host.
See Section 11 for the AC timing of the serial port. All serial port accesses are LSB first. See Figure 3-1,
Figure 3-2, Figure 3-3, and Figure 3-4 for more details.
Reading or writing to the internal registers requires writing one address/command byte prior to
transferring register data. The first bit written (LSB) of the address/command byte specifies whether the
access is a read (1) or a write (0). The next 5 bits identify the register address. Bit 7 is reserved and must
be set to 0 for proper operation.
The last bit (MSB) of the address/command byte is the burst mode bit. When the burst bit is enabled
(B = 1) and a READ operation is performed, addresses 0 through 15h are read sequentially, starting at
address 0h. And when the burst bit is enabled and a WRITE operation is performed, addresses 0 through
16h are written sequentially, starting at address 0h. Burst operation is stopped once address 15h is read.
See Figure 3-5 and Figure 3-6 for more details.
All data transfers are initiated by driving the CS input low. When Input Clock-Edge Select (ICES) is low,
input data is latched on the rising edge of SCLK and when ICES is high, input data is latched on the
falling edge of SCLK. When Output Clock-Edge Select (OCES) is low, data is output on the falling edge
of SCLK and when OCES is high, data is output on the rising edge of SCLK. Data is held until the next
falling or rising edge. All data transfers are terminated if the CS input transitions high. Port control logic
is disabled and SDO is tri-stated when CS is high.
26 of 76
DS21348/DS21Q348
Figure 3-1. Serial Port Operation for Read Access (R = 1) Mode 1
ICES = 1 (sample SDI on the falling edge of SCLK)
OCES = 1 (update SDO on rising edge of SCLK)
1
SCLK
2
3
4
5
6
A0
A1
A2
A32
A4
7
8
9
10
11
12
13
14
15
16
D0
D1
D2
D3
D4
D5
D6
CS
SDI
1
0
B
(lsb)
(msb)
READ ACCESS ENABLED
SDO
D7
(lsb)
(msb)
Figure 3-2. Serial Port Operation for Read Access Mode 2
ICES = 1 (sample SDI on the falling edge of SCLK)
OCES = 0 (update SDO on falling edge of SCLK)
1
SCLK
2
3
4
5
6
7
A0
A1
A2
A3
A4
8
9
10
11
12
13
14
15
16
CS
SDI
1
0
(lsb)
B
(msb)
SDO
D0
D1
D2
D3
D4
D5
D6
(lsb)
D7
(msb)
Figure 3-3. Serial Port Operation for Read Access Mode 3
ICES = 0 (sample SDI on the rising edge of SCLK)
OCES = 0 (update SDO on falling edge of SCLK)
1
SCLK
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CS
SDI
1
(lsb)
SDO
A0
A1
A2
A3
A4
0
B
(msb)
D0
(lsb)
27 of 76
D1
D2
D3
D4
D5
D6
D7
(msb)
DS21348/DS21Q348
Figure 3-4. Serial Port Operation for Read Access Mode 4
ICES = 0 (sample SDI on the rising edge of SCLK)
OCES = 1 (update SDO on rising edge of SCLK)
1
SCLK
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CS
SDI
A0
1
A1
A2
A3A5
A4
B
0
(lsb)
(msb)
SDO
D0
D1
D2
D3
D4
D5
D6
D7
(lsb)
(msb)
Figure 3-5. Serial Port Operation for Write Access (R = 0) Modes 1 and 2
ICES = 1 (sample SDI on the falling edge of SCLK)
SCLK
1
2
3
4
5
6
7
A0
A1
A2
A3
A4
8
9
10
11
12
13
14
15
B
D0
D1
D2
D3
D4
D5
D6
16
CS
SDI
0
0
(lsb)
(msb)
(lsb)
D7
(msb)
WRITE ACCESS ENABLED
SDO
Figure 3-6. Serial Port Operation for Write Access (R = 0) Modes 3 and 4
D0
D0
ICES = 0 (sample SDI on the rising edge of SCLK)
SCLK
1
2
3
4
5
6
0
A0
A1
A2
A3
A4
7
8
9
10
11
12
13
14
15
16
CS
SDI
(lsb)
0
B
(msb)
D0
(lsb)
WRITE ACCESS ENABLED
SDO
28 of 76
D1
D2
D3
D4
D5
D6
D7
(msb)
DS21348/DS21Q348
4. CONTROL REGISTERS
CCR1 (00H): COMMON CONTROL REGISTER 1
(MSB)
ETS
NRZE
SYMBOL
POSITION
ETS
CCR1.7
NRZE
CCR1.6
RCLA
CCR1.5
ECUE
CCR1.4
JAMUX
CCR1.3
TTOJ
CCR1.2
TTOR
CCR1.1
LOTCMC
CCR1.0
RCLA
ECUE
JAMUX
TTOJ
TTOR
(LSB)
LOTCMC
DESCRIPTION
E1/T1 Select.
0 = E1
1 = T1
NRZ Enable.
0 = Bipolar data at RPOS/RNEG and TPOS/TNEG
1 = NRZ data at RPOS and TPOS or TNEG; RNEG outputs a positive
going pulse when device receives a BPV, CV, or EXZ. See Figure 1-2
and Figure 1-3.
Receive Carrier Loss Alternate Criteria.
0 = RCL declared upon 255 (E1) or 192 (T1) consecutive zeros
1 = RCL declared upon 2048 (E1) or 1544 (T1) consecutive zeros
Error Counter Update Enable. A 0 to 1 transition forces the next clock
cycle to load the error counter registers with the latest counts and reset
the counters. The user must wait a minimum of two clocks cycles (976ns
for E1 and 1296ns for T1) before reading the error count registers to
allow for a proper update. See Section 4 and Figure 1-2 for details.
Jitter Attenuator MUX. Controls the source for JACLK (Figure 1-1).
0 = JACLK sourced from MCLK (2.048MHz or 1.544MHz at MCLK)
1 = JACLK sourced from internal PLL (2.048MHz at MCLK)
TCLK to JACLK. Internally connects TCLK to JACLK (Figure 1-3).
0 = disabled
1 = enabled
TCLK to RCLK. Internally connects TCLK to RCLK (Figure 1-3).
0 = disabled
1 = enabled
Loss Of Transmit Clock Mux Control. Determines whether the
transmit logic should switch to JACLK if the TCLK input should fail to
transition (Figure 1-3).
0 = do not switch to JACLK if TCLK stops
1 = switch to JACLK if TCLK stops
29 of 76
DS21348/DS21Q348
Table 4-1. MCLK Selection
MCLK
(MHz)
2.048
2.048
1.544
JAMUX
(CCR1.3)
0
1
0
ETS
(CCR1.7)
0
1
1
CCR2 (01H): COMMON CONTROL REGISTER 2
(MSB)
P25S
n/a
SYMBOL
POSITION
P25S
CCR2.7
SCLD
CCR2.6
CCR2.5
CLDS
CCR2.4
RHBE
CCR2.3
THBE
CCR2.2
TCES
CCR2.1
RCES
CCR2.0
SCLD
CLDS
RHBE
THBE
TCES
(LSB)
RCES
DESCRIPTION
Pin 25 Select. Forced to logic 0 in hardware mode.
0 = toggles high during a Receive Carrier Loss condition
1 = toggles high if TCLK does not transition for at least 5µs
Not Assigned. Should be set to zero when written to.
Short Circuit Limit Disable (ETS = 0). Controls the 50 mA (rms)
current limiter.
0 = enable 50 mA current limiter
1 = DISABLE 50 MA CURRENT LIMITER
Custom Line Driver Select. Setting this bit to a one will redefine the
operation of the transmit line driver. When this bit is set to a one and
CCR4.5 = CCR4.6 = CCR4.7 = 0, then the device will generate a square
wave at the TTIP and TRING outputs instead of a normal waveform.
When this bit is set to a one and CCR4.5 = CCR4.6 = CCR4.7 ≠ 0, then
the device will force TTIP and TRING outputs to become open drain
drivers instead of their normal push-pull operation. This bit should be set
to zero for normal operation of the device. Contact the factory for more
details on how to use this bit.
Receive HDB3/B8ZS Enable. See Figure 1-2.
0 = enable HDB3 (E1)/B8ZS (T1)
1 = disable HDB3 (E1)/B8ZS (T1)
Transmit HDB3/B8ZS Enable. See Figure 1-3.
0 = enable HDB3 (E1)/B8ZS (T1)
1 = disable HDB3 (E1)/B8ZS (T1)
Transmit Clock Edge Select. Selects which TCLK edge to sample TPOS
and TNEG. See Figure 1-3.
0 = sample TPOS and TNEG on falling edge of TCLK
1 = sample TPOS and TNEG on rising edge of TCLK
Receive Clock Edge Select. Selects which RCLK edge to update RPOS
and RNEG. See Figure 1-2.
0 = update RPOS and RNEG on rising edge of RCLK
1 = update RPOS and RNEG on falling edge of RCLK
30 of 76
DS21348/DS21Q348
CCR3 (02H): COMMON CONTROL REGISTER 3
(MSB)
TUA1
ATUA1
SYMBOL
POSITION
TUA1
CCR3.7
ATUA1
CCR3.6
TAOZ
CCR3.5
TPRBSE
CCR3.4
TLCE
CCR3.3
LIRST
CCR3.2
IBPV
CCR3.1
IBE
CCR3.0
TAOZ
TPRBSE
TLCE
LIRST
IBPV
(LSB)
IBE
DESCRIPTION
Transmit Unframed All Ones. The polarity of this bit is set such that the
device will transmit an all ones pattern on power-up or device reset. This
bit must be set to a one to allow the device to transmit data. The
transmission of this data pattern is always timed off of the JACLK (See
Figure 1-1).
0 = transmit all ones at TTIP and TRING
1 = transmit data normally
Automatic Transmit Unframed All Ones. Automatically transmit an
unframed all ones pattern at TTIP and TRING during a receive carrier loss
(RCL) condition or receive all ones condition.
0 = disabled
1 = enabled
Transmit Alternate Ones and Zeros. Transmit a …101010… pattern at
TTIP and TRING. The transmission of this data pattern is always timed
off of TCLK (Figure 1-1).
0 = disabled
1 = enabled
Transmit PRBS Enable. Transmit a 215 - 1 (E1) or a 220 - 1 (T1) PRBS at
TTIP and TRING (Figure 1-3).
0 = disabled
1 = enabled
Transmit Loop Code Enable. Enables the transmit side to transmit the
loop up code in the Transmit Code Definition registers (TCD1 and
TCD2). See Section 4 and Figure 1-3 for details.
0 = disabled
1 = enabled
Line Interface Reset. Setting this bit from a zero to a one will initiate an
internal reset that resets the clock recovery state machine and re-centers
the jitter attenuator. Normally this bit is only toggled on power-up. Must
be cleared and set again for a subsequent reset.
Insert BPV. A 0 to 1 transition on this bit will cause a single BiPolar
Violation (BPV) to be inserted into the transmit data stream. Once this bit
has been toggled from a 0 to a 1, the device waits for the next occurrence
of three consecutive ones to insert the BPV. This bit must be cleared and
set again for a subsequent error to be inserted (Figure 1-3).
Insert Bit Error. A 0 to 1 transition on this bit will cause a single logic
error to be inserted into the transmit data stream. This bit must be cleared
and set again for a subsequent error to be inserted (Figure 1-3).
31 of 76
DS21348/DS21Q348
4.1 Device Power-Up and Reset
The DS21348 will reset itself upon power-up setting all writeable registers to 00h and clear the status and
information registers. CCR3.7 (TUA1) = 0 results in the LIU transmitting unframed all ones. After the
power supplies have settled following power-up, initialize all control registers to the desired settings, then
toggle the LIRST bit (CCR3.2). At anytime, the DS21348 can be reset to the default settings by bringing
HRST (pin 29) low (level triggered) or by powering down and powering up again.
CCR4 (03H): COMMON CONTROL REGISTER 4
(MSB)
L2
L1
SYMBOL
POSITION
L2
CCR4.7
L1
CCR4.6
L0
CCR4.5
EGL
CCR4.4
JAS
CCR4.3
JABDS
CCR4.2
DJA
CCR4.1
TPD
CCR4.0
L0
EGL
JAS
ETS
(CCR1.7)
0 (E1)
0 (E1)
1 (T1)
1 (T1)
DJA
DESCRIPTION
Line Build Out Select Bit 2. Sets the transmitter build out; see Table 7-1
for E1 and Table 7-2 for T1.
Line Build Out Select Bit 1. Sets the transmitter build out; see Table 7-1
for E1 and Table 7-2 for T1.
Line Build Out Select Bit 0. Sets the transmitter build out; see Table 7-1
for E1 and Table 7-2 for T1.
Receive Equalizer Gain Limit. This bit controls the sensitivity of the
receive equalizer. See Table 4-2.
Jitter Attenuator Select.
0 = place the jitter attenuator on the receive side
1 = place the jitter attenuator on the transmit side
Jitter Attenuator Buffer Depth Select.
0 = 128 bits
1 = 32 bits (use for delay-sensitive applications)
Disable Jitter Attenuator.
0 = jitter attenuator enabled
1 = jitter attenuator disabled
Transmit Power-Down.
0 = normal transmitter operation
1 = powers down the transmitter and tri-states the TTIP and TRING pins
Table 4-2. Receive Equalizer Sensitivity Settings
EGL
(CCR4.4)
0
1
1
0
JABDS
(LSB)
TPD
RECEIVE
SENSITIVITY
-12dB (short haul)
-43dB (long haul)
-30dB (limited long haul)
-36dB (long haul)
32 of 76
DS21348/DS21Q348
CCR5 (04H): COMMON CONTROL REGISTER 5
(MSB)
BPCS1
BPCS0
MM1
MM0
RSCLKE
TSCLKE
RT1
(LSB)
RT0
SYMBOL
POSITION
DESCRIPTION
BPCS1
CCR5.7
Backplane Clock Select 1. See Table 4-3 for details.
BPCS0
CCR5.6
Backplane Clock Select 0. See Table 4-3 for details
MM1
CCR5.5
Monitor Mode 1. See Table 4-4.
MM0
CCR5.4
Monitor Mode 0. See Table 4-4.
RSCLKE
CCR5.3
TSCLKE
CCR5.2
RT1
CCR5.1
Receive Synchronization Clock Enable.
This control bit determines whether the line receiver should handle normal
T1/E1 signals or a synchronization signal.
E1 mode:
0 = receive normal E1 signal (Section 6 of G.703)
1 = receive 2.048MHz synchronization signal (Section 10 of G.703)
T1 mode:
0 = receive normal T1 signal
1 = receive 1.544MHz synchronization signal
Transmit Synchronization Clock Enable.
This control bit determines whether the transmitter should transmit normal
T1/E1 signals or a synchronized signal.
E1 mode:
0 = transmit normal E1 signal (Section 6 of G.703)
1 = transmit 2.048MHz synchronization signal (Section 10 of G.703)
T1 mode:
0 = transmit normal T1 signal
1 = transmit 1.544MHz synchronization signal
Receive Termination 1. See Table 4-5 for details.
RT0
CCR5.0
Receive Termination 0. See Table 4-5 for details.
33 of 76
DS21348/DS21Q348
Table 4-3. Backplane Clock Select
BPCS1
(CCR5.7)
0
0
1
1
BPCS0
(CCR5.6)
0
1
0
1
BPCLK
FREQUENCY
16.384MHz
8.192MHz
4.096MHz
2.048MHz
Table 4-4. Monitor Gain Settings
MM1
(CCR5.5)
MM0
(CCR5.4)
0
0
0
1
1
1
0
1
INTERNAL LINEAR
GAIN BOOST
Normal operation
(no boost)
20dB
26dB
32dB
Table 4-5. Internal Rx Termination Select
RT1
(CCR5.1)
0
0
1
1
RT0
(CCR5.0)
0
1
0
1
INTERNAL RECEIVE
TERMINATION CONFIGURATION
Internal receive-side termination disabled
Internal receive-side 120Ω enabled
Internal receive-side 100Ω enabled
Internal receive-side 75Ω enabled
34 of 76
DS21348/DS21Q348
CCR6 (05H): COMMON CONTROL REGISTER 6
(MSB)
LLB
RLB
ARLBE
ALB
RJAB
ECRS2
ECRS1
(LSB)
ECRS0
SYMBOL
POSITION
DESCRIPTION
LLB
CCR6.7
RLB
CCR6.6
ARLBE
CCR6.5
ALB
CCR6.4
Analog Loopback. In Analog Loopback (ALB), signals at TTIP and TRING
will be internally connected to RTIP and RRING. The incoming signals, from
the line, at RTIP and RRING will be ignored. The signals at TTIP and TRING
will be transmitted as normal. See Figure 1-1 and Section 6.2.3 for more details.
0 = loopback disabled
1 = loopback enabled
RJAB
CCR6.3
ECRS2
CCR6.2
RCLK Jitter Attenuator Bypass. This control bit allows the receive recovered
clock and data to bypass the jitter attenuation while still allowing the BPCLK
output to use the jitter attenuator. See Figure 1-1 and Section 7.3 for details.
0 = disabled
1 = enabled
Error Count Register Select 2. See Section 6.4 for details.
ECRS1
CCR6.1
Error Count Register Select 1. See Section 6.4 for details.
ECRS0
CCR6.0
Error Count Register Select 0. See Section 6.4 for details.
Local Loopback. In Local Loopback (LLB), transmit data will be looped back
to the receive path passing through the jitter attenuator if it is enabled. Data in
the transmit path will act as normal. See Figure 1-1 and Section 6.2.2 for
details.
0 = loopback disabled
1 = loopback enabled
Remote Loopback. In Remote Loopback (RLB), data output from the
clock/data recovery circuitry will be looped back to the transmit path passing
through the jitter attenuator if it is enabled. Data in the receive path will act as
normal while data presented at TPOS and TNEG will be ignored.
See Figure 1-1 and Section 6.2.1 for details.
0 = loopback disabled
1 = loopback enabled
Automatic Remote Loopback Enable and Reset. When this bit is set high,
the device will automatically go into remote loopback when it detects loop up
code programmed into the Receive Loop-Up Code Definition Registers
(RUPCD1 and RUPCD2) for a minimum of 5 seconds and it will also set the
RIR2.1 status bit. Once in a RLB state, it will remain in this state until it has
detected the loop code programmed into the Receive Loop-Down Code
Definition Registers (RDNCD1 and RDNCD2) for a minimum of 5 seconds at
which point it will force the device out of RLB and clear RIR2.1. The
automatic RLB circuitry can be reset by toggling this bit from a 1 to a 0. The
action of the automatic remote loopback circuitry is logically ORed with the
RLB (CCR6.6) control bit (i.e., either one can cause a RLB to occur).
35 of 76
DS21348/DS21Q348
5. STATUS REGISTERS
There are three registers that contain information on the current real-time status of the device, Status
Register (SR) and Receive Information Registers 1 and 2 (RIR1/RIR2). When a particular event has
occurred (or is occurring), the appropriate bit in one of these three registers will be set to a one. Some of
the bits in SR, RIR1, and RIR2 are latched bits and some are real time bits. The register descriptions
below list which status bits are latched and which are real time bits. For latched status bits, when an event
or an alarm occurs the bit is set to a one and will remain set until the user reads that bit. The bit will be
cleared when it is read and it will not be set again until the event has occurred again. Two of the latched
status bits (RUA1 and RCL) will remain set after reading if the alarm is still present.
The user will always precede a read of any of the three status registers with a write. The byte written to
the register will inform the DS21348 which bits the user wishes to read and have cleared. The user will
write a byte to one of these registers with a one in the bit positions to be read and a zero in the other bit
positions. When a one is written to a bit location, that location will be updated with the latest information.
When a zero is written to a bit position, that bit position will not be updated and the previous value will
be held. A write to the status and information registers will be immediately followed by a read of the
same register. The read result should be logically ANDed with the mask byte that was just written and
this value should be written back into the same register to insure that bit does indeed clear. This second
write step is necessary because the alarms and events in the status registers occur asynchronously with
respect to their access via the parallel port. This write-read-write scheme allows an external
microcontroller or microprocessor to individually poll certain bits without disturbing the other bits in the
register. This operation is key in controlling the DS21348 with higher-order software languages.
The bits in the SR register have the unique ability to initiate a hardware interrupt via the INT output pin.
Each of the alarms and events in the SR can be either masked or unmasked from the interrupt pin via the
Interrupt Mask Register (IMR). The interrupts caused by the RCL, RUA1, and LOTC bits in SR act
differently than the interrupts caused by the other status bits in SR. The RCL, RUA1 and LOTC bits will
force the INT pin low whenever they change state (i.e., go active or inactive). The INT pin will be
allowed to return high (if no other interrupts are present) when the user reads the alarm bit that caused the
interrupt to occur even if the alarm is still present. The other status bits in SR can force the INT pin low
when they are set. The INT pin will be allowed to return high (if no other interrupts are present) when the
user reads the event bit that caused the interrupt to occur.
Table 5-1. Received Alarm Criteria
ALARM
E1/T1
SET CRITERIA
RUA1
E1
Less than 2 zeros in two frames (512 bits)
RUA1
T1
RCL1
E1
RCL1
T1
Note 1:
Note 2:
Over a 3ms window, five or fewer zeros
are received
255 (or 2048)2 consecutive zeros received
(G.775)
192 (or 1544)2 consecutive zeros are
received
CLEAR CRITERIA
More than 2 zeros in two frames (512
bits)
Over a 3ms window, six or more zeros
are received
In 255 bit times, at least 32 ones are
received
14 or more ones out of 112 possible
bit positions are received starting with
the first one received
Receive carrier loss (RCL) is also known as loss of signal (LOS) or Red Alarm in T1.
See CCR1.5 for details.
36 of 76
DS21348/DS21Q348
SR (06H): STATUS REGISTER
(MSB)
LUP
LDN
SYMBOL
POSITION
LUP
(latched)
LDN
(latched)
SR.7
LOTC
(real time)
RUA1
(latched)
RCL
(latched)
TCLE
(real time)
TOCD
(real time)
PRBSD
(real time)
SR.6
SR.5
SR.4
SR.3
SR.2
SR.1
SR.0
LOTC
RUA1
RCL
TCLE
TOCD
(LSB)
PRBSD
DESCRIPTION
Loop-Up Code Detected. Set when the loop-up code defined in registers
RUPCD1 and RUPCD2 is being received. See Section 4 for details.
Loop-Down Code Detected. Set when the loop-down code defined in
registers RDNCD1 and RDNCD2 is being received. See Section 4 for
details.
Loss of Transmit Clock. Set when the TCLK pin has not transitioned for
5µsec (±2µs). Will force the LOTC pin high.
Receive Unframed All Ones. Set when an unframed all ones code is
received at RRING and RTIP. See Table 5-1 for details.
Receive Carrier Loss. Set when a receive carrier loss condition exists at
RRING and RTIP. See Table 5-1 for details.
Transmit Current Limit Exceeded. Set when the 50mA (RMS) current
limiter is activated whether the current limiter is enabled or not.
Transmit Open Circuit Detect. Set when the device detects that the TTIP
and TRING outputs are open circuited.
PRBS Detect. Set when the receive-side detects a 215 - 1 (E1) or a 220 - 1
(T1) Pseudo-Random Bit Sequence (PRBS).
37 of 76
DS21348/DS21Q348
IMR (07H): INTERRUPT MASK REGISTER
(MSB)
LUP
LDN
LOTC
SYMBOL
POSITION
LUP
IMR.7
LDN
IMR.6
LOTC
IMR.5
RUA1
IMR.4
RCL
IMR.3
TCLE
IMR.2
TOCD
IMR.1
PRBSD
IMR.0
RUA1
RCL
TCLE
DESCRIPTION
Loop-Up Code Detected.
0 = interrupt masked
1 = interrupt enabled
Loop-Down Code Detected.
0 = interrupt masked
1 = interrupt enabled
Loss of Transmit Clock.
0 = interrupt masked
1 = interrupt enabled
Receive Unframed All Ones.
0 = interrupt masked
1 = interrupt enabled
Receive Carrier Loss.
0 = interrupt masked
1 = interrupt enabled
Transmit Current Limiter Exceeded.
0 = interrupt masked
1 = interrupt enabled
Transmit Open Circuit Detect.
0 = interrupt masked
1 = interrupt enabled
PRBS Detection.
0 = interrupt masked
1 = interrupt enabled
38 of 76
TOCD
(LSB)
PRBSD
DS21348/DS21Q348
RIR1 (08H): RECEIVE INFORMATION REGISTER 1
(MSB)
ZD
16ZD
HBD
SYMBOL
POSITION
ZD
(latched)
RIR1.7
16ZD
(latched)
RIR1.6
HBD
(latched)
RIR1.5
RCLC
(latched)
RUA1C
(latched)
JALT
(latched)
RIR1.4
RCLC
RUA1C
JALT
n/a
(LSB)
n/a
DESCRIPTION
N/A
RIR1.1
Zero Detect. Set when a string of at least four (ETS = 0) or eight
(ETS = 1) consecutive zeros (regardless of the length of the string)
have been received. Will be cleared when read.
Sixteen Zero Detect. Set when at least 16 consecutive zeros
(regardless of the length of the string) have been received. Will be
cleared when read.
HDB3/B8ZS Word Detect. Set when an HDB3 (ETS = 0) or B8ZS
(ETS = 1) code word is detected independent of whether the receive
HDB3/B8ZS mode (CCR4.6) is enabled. Will be cleared when read.
Useful for automatically setting the line coding.
Receive Carrier Loss Clear. Set when the RCL alarm has met the
clear criteria defined in Table 5-1. Will be cleared when read.
Receive Unframed All Ones Clear. Set when the unframed all ones
signal is no longer detected. Will be cleared when read (Table 5-1).
Jitter Attenuator Limit Trip. Set when the jitter attenuator FIFO
reaches to within 4 bits of its useful limit. Will be cleared when read.
Useful for debugging jitter attenuation operation.
Not Assigned. Could be any value when read.
N/A
RIR1.0
Not Assigned. Could be any value when read.
RIR1.3
RIR1.2
39 of 76
DS21348/DS21Q348
RIR2 (09H): RECEIVE INFORMAION REGISTER 2
(MSB)
RL3
RL2
RL1
RL0
N/A
N/A
ARLB
(LSB)
SEC
SYMBOL
POSITION
DESCRIPTION
RL3
(real time)
RL2
(real time)
RL1
(real time)
RL0
(real time)
N/A
RIR2.7
Receive Level Bit 3. See Table 5-2.
RIR2.6
Receive Level Bit 2. See Table 5-2.
RIR2.5
Receive Level Bit 1. See Table 5-2.
RIR2.4
Receive Level Bit 0. See Table 5-2.
RIR2.3
Not Assigned. Could be any value when read.
N/A
RIR2.2
Not Assigned. Could be any value when read.
ARLB
(real time)
RIR2.1
SEC
(latched)
RIR2.0
Automatic Remote Loopback Detected. This bit will be set to a one
when the automatic Remote Loopback (RLB) circuitry has detected
the presence of a loop up code for 5 seconds. It will remain set until
the automatic RLB circuitry has detected the loop down code for 5
seconds. See Section 4 for more details. This bit will be forced low
when the automatic RLB circuitry is disabled (CCR6.5 = 0).
One-Second Timer. This bit will be set to a one on one-second
boundaries as timed by the device based on the RCLK. It will be
cleared when read.
Table 5-2. Receive Level Indication
RL3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
RL2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
RL1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
RL0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
RECEIVE LEVEL (dB)
< -2.5
-2.5 to -5.0
-5.0 to -7.5
-7.5 to -10.0
-10.0 to -12.5
-12.5 to -15.0
-15.0 to -17.5
-17.5 to -20.0
-20.0 to -22.5
-22.5 to -25.0
-25.0 to -27.5
-27.5 to -30.0
-30.0 to -32.5
-32.5 to -35.0
-35.0 to -37.5
> -37.5
40 of 76
DS21348/DS21Q348
6. DIAGNOSTICS
6.1 In-Band Loop Code Generation and Detection
The DS21348 can generate and detect a repeating bit pattern that is from one to eight or sixteen bits in
length. To transmit a pattern, the user will load the pattern to be sent into the Transmit Code Definition
(TCD1 and TCD2) registers and select the proper length of the pattern by setting the TC0 and TC1 bits in
the In-Band Code Control (IBCC) register. When generating a 1, 2, 4, 8, or 16 bit pattern both the
transmit code registers (TCD1 and TCD2) must be filled with the proper code. Generation of a 1, 3, 5, or
7-bit pattern only requires TCD1 to be filled. Once this is accomplished, the pattern will be transmitted as
long as the TLCE control bit (CCR3.3) is enabled. As an example, if the user wished to transmit the
standard “loop up” code for Channel Service Units which is a repeating pattern of ...10000100001... then
80h would be loaded into TCD1 and the length would set using TC1 and TC0 in the IBCC register to 5
bits.
The DS21348 can detect two separate repeating patterns to allow for both a “loop up” code and a “loop
down” code to be detected. The user will program the codes to be detected in the Receive Up Code
Definition (RUPCD1 and RUPCD2) registers and the Receive Down Code Definition (RDNCD1 and
RDNCD2) registers and the length of each pattern will be selected via the IBCC register. The DS21348
will detect repeating pattern codes with bit error rates as high as 1x10-2. The code detector has a nominal
integration period of 48ms, hence, after about 48ms of receiving either code, the proper status bit (LUP at
SR.7 and LDN at SR.6) will be set to a one. Normally codes are sent for a period of 5 seconds. It is
recommended that the software poll the DS21348 every 100ms to 1000ms until 5 seconds has elapsed to
insure that the code is continuously present.
IBCC (0AH): IN-BAND CODE CONTROL REGISTER
(MSB)
TC1
TC0
RUP2
RUP1
RUP0
RDN2
RDN1
(LSB)
RDN0
SYMBOL
POSITION
DESCRIPTION
TC1
IBCC.7
Transmit Code Length Definition Bit 1. See Table 6-1.
TC0
IBCC.6
Transmit Code Length Definition Bit 0. See Table 6-1.
RUP2
IBCC.5
Receive Up Code Length Definition Bit 2. See Table 6-2.
RUP1
IBCC.4
Receive Up Code Length Definition Bit 1. See Table 6-2.
RUP0
IBCC.3
Receive Up Code Length Definition Bit 0. See Table 6-2.
RDN2
IBCC.2
Receive Down Code Length Definition Bit 2. See Table 6-2.
RDN1
IBCC.1
Receive Down Code Length Definition Bit 1. See Table 6-2.
RDN0
IBCC.0
Receive Down Code Length Definition Bit 0. See Table 6-2.
Table 6-1. Transmit Code Length
41 of 76
DS21348/DS21Q348
TC1
TC0
0
0
1
1
0
1
0
1
LENGTH SELECTED
(BITS)
5
6/3
7
16/8/4/2/1
Table 6-2. Receive Code Length
RUP2/RDN2 RUP1/ RDN1
0
0
0
0
1
1
1
1
RUP0/RDN0
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
LENGTH
SELECTED (BITS)
1
2
3
4
5
6
7
16/8
TCD1 (0BH): TRANSMIT CODE DEFINITION REGISTER 1
(MSB)
C7
C6
C5
C4
C3
C2
C1
(LSB)
C0
SYMBOL
POSITION
DESCRIPTION
C7
TCD1.7
C6
TCD1.6
Transmit Code Definition Bit 7. First bit of the repeating
pattern.
Transmit Code Definition Bit 6.
C5
TCD1.5
Transmit Code Definition Bit 5.
C4
TCD1.4
Transmit Code Definition Bit 4.
C3
TCD1.3
Transmit Code Definition Bit 3.
C2
TCD1.2
C1
TCD1.1
C0
TCD1.0
Transmit Code Definition Bit 2. A Don’t Care if a 5-bit
length is selected.
Transmit Code Definition Bit 1. A Don’t Care if a 5-bit or 6bit length is selected.
Transmit Code Definition Bit 0. A Don’t Care if a 5-bit, 6bit, or 7-bit length is selected.
42 of 76
DS21348/DS21Q348
TCD2 (0CH): TRANSMIT CODE DEFINITION REGISTER 2
(MSB)
C15
C14
C13
C12
C11
C10
SYMBOL
POSITION
C15
TCD2.7
Transmit Code Definition Bit 15
C14
TCD2.6
Transmit Code Definition Bit 14
C13
TCD2.5
Transmit Code Definition Bit 13
C12
TCD2.4
Transmit Code Definition Bit 12
C11
TCD2.3
Transmit Code Definition Bit 11
C10
TCD2.2
Transmit Code Definition Bit 10
C9
TCD2.1
Transmit Code Definition Bit 9
C8
TCD2.0
Transmit Code Definition Bit 8
C9
(LSB)
C8
DESCRIPTION
RUPCD1 (0DH): RECEIVE UP CODE DEFINITION REGISTER 1
(MSB)
C7
C6
C5
C4
C3
C2
C1
(LSB)
C0
SYMBOL
POSITION
DESCRIPTION
C7
RUPCD1.7
C6
RUPCD1.6
C5
RUPCD1.5
C4
RUPCD1.4
C3
RUPCD1.3
C2
RUPCD1.2
C1
RUPCD1.1
C0
RUPCD1.0
Receive Up Code Definition Bit 7. First bit of the repeating
pattern.
Receive Up Code Definition Bit 6. A Don’t Care if a 1-bit
length is selected.
Receive Up Code Definition Bit 5. A Don’t Care if a 1-bit or
2-bit length is selected.
Receive Up Code Definition Bit 4. A Don’t Care if a 1-bit to
3-bit length is selected.
Receive Up Code Definition Bit 3. A Don’t Care if a 1-bit to
4-bit length is selected.
Receive Up Code Definition Bit 2. A Don’t Care if a 1-bit to
5-bit length is selected.
Receive Up Code Definition Bit 1. A Don’t Care if a 1-bit to
6-bit length is selected.
Receive Up Code Definition Bit 0. A Don’t Care if a 1-bit to
7-bit length is selected.
43 of 76
DS21348/DS21Q348
RUPCD2 (0EH): RECEIVE UP CODE DEFINITION REGISTER 2
(MSB)
C15
C14
C13
C12
C11
C10
SYMBOL
POSITION
DESCRIPTION
C15
RUPCD2.7
Receive Up Code Definition Bit 15
C14
RUPCD2.6
Receive Up Code Definition Bit 14
C13
RUPCD2.5
Receive Up Code Definition Bit 13
C12
RUPCD2.4
Receive Up Code Definition Bit 12
C11
RUPCD2.3
Receive Up Code Definition Bit 11
C10
RUPCD2.2
Receive Up Code Definition Bit 10
C9
RUPCD2.1
Receive Up Code Definition Bit 9
C8
RUPCD2.0
Receive Up Code Definition Bit 8
C9
(LSB)
C8
RDNCD1 (0FH): RECEIVE DOWN CODE DEFINITION REGISTER 1
(MSB)
C7
C6
C5
C4
C3
C2
C1
(LSB)
C0
SYMBOL
POSITION
DESCRIPTION
C7
RDNCD1.7
C6
RDNCD1.6
C5
RDNCD1.5
C4
RDNCD1.4
C3
RDNCD1.3
C2
RDNCD1.2
C1
RDNCD1.1
C0
RDNCD1.0
Receive Down Code Definition Bit 7. First bit of the
repeating pattern.
Receive Down Code Definition Bit 6. A Don’t Care if a 1-bit
length is selected.
Receive Down Code Definition Bit 5. A Don’t Care if a 1-bit
or 2-bit length is selected.
Receive Down Code Definition Bit 4. A Don’t Care if a 1-bit
to 3-bit length is selected.
Receive Down Code Definition Bit 3. A Don’t Care if a 1-bit
to 4-bit length is selected.
Receive Down Code Definition Bit 2. A Don’t Care if a 1-bit
to 5-bit length is selected.
Receive Down Code Definition Bit 1. A Don’t Care if a 1-bit
to 6-bit length is selected.
Receive Down Code Definition Bit 0. A Don’t Care if a 1-bit
to 7-bit length is selected.
44 of 76
DS21348/DS21Q348
RDNCD2 (10H): RECEIVE DOWN CODE DEFINITION REGISTER 2
(MSB)
C15
C14
C13
C12
C11
C10
SYMBOL
POSITION
DESCRIPTION
C15
RDNCD2.7
Receive Down Code Definition Bit 15
C14
RDNCD2.6
Receive Down Code Definition Bit 14
C13
RDNCD2.5
Receive Down Code Definition Bit 13
C12
RDNCD2.4
Receive Down Code Definition Bit 12
C11
RDNCD2.3
Receive Down Code Definition Bit 11
C10
RDNCD2.2
Receive Down Code Definition Bit 10
C9
RDNCD2.1
Receive Down Code Definition Bit 9
C8
RDNCD2.0
Receive Down Code Definition Bit 8
45 of 76
C9
(LSB)
C8
DS21348/DS21Q348
6.2 Loopbacks
6.2.1 Remote Loopback (RLB)
When RLB (CCR6.6) is enabled, the DS21348 is placed into remote loopback. In this loopback, data
from the clock/data recovery state machine will be looped back to the transmit path passing through the
jitter attenuator if it is enabled. The data at the RPOS and RNEG pins will be valid while data presented
at TPOS and TNEG will be ignored. See Figure 1-1 for details.
If the Automatic Remote Loop Back Enable (CCR6.5) is set to a one, the DS21348 will automatically go
into remote loop back when it detects the loop-up code programmed in the Receive Up Code Definition
Registers (RUPCD1 and RUPCD2) for a minimum of 5 seconds. When the DS21348 detects the loop
down code programmed in the Receive Loop-Down Code Definition registers (RDNCD1 and RDNCD2)
for a minimum of 5 seconds, the DS21348 will come out of remote loop back. The ARLB can also be
disabled by setting ARLBE to a zero.
6.2.2 Local Loopback (LLB)
When LLB (CCR6.7) is set to a one, the DS21348 is placed into Local Loopback. In this loopback, data
on the transmit-side will continue to be transmitted as normal. TCLK and TPOS/TNEG will pass through
the jitter attenuator (if enabled) and be output at RCLK and RPOS/RNEG. Incoming data from the line at
RTIP and RRING will be ignored. If Transmit Unframed All Ones (CCR3.7) is set to a one while in LLB,
TTIP and TRING will transmit all ones while TCLK and TPOS/TNEG will be looped back to RCLK and
RPOS/RNEG. See Figure 1-1 for more details.
6.2.3 Analog Loopback (ALB)
Setting ALB (CCR6.4) to a one puts the DS21348 in Analog Loopback. Signals at TTIP and TRING will
be internally connected to RTIP and RRING. The incoming signals at RTIP and RRING will be ignored.
The signals at TTIP and TRING will be transmitted as normal. See Figure 1-1 for more details.
6.2.4 Dual Loopback (DLB)
Setting both CCR6.7 and CCR6.6 to a one, LLB and RLB respectively, puts the DS21348 into Dual
Loopback operation. The TCLK and TPOS/TNEG signals will be looped back through the jitter
attenuator (if enabled) and output at RCLK and RPOS/RNEG. Clock and data recovered from RTIP and
RRING will be looped back to the transmit-side and output at TTIP and TRING. This mode of operation
is not available when implementing hardware operation. See Figure 1-1 for more details.
46 of 76
DS21348/DS21Q348
6.3 PRBS Generation and Detection
Setting TPRBSE (CCR3.4) = 1 enables the DS21348 to transmit a 215 - 1 (E1) or a 220 - 1 (T1) PseudoRandom Bit Sequence (PRBS) depending on the ETS bit setting in CCR1.7. The receive-side of the
DS21348 will always search for these PRBS patterns independent of CCR3.4. The PRBS Bit Error
Output (PBEO) will remain high until the receiver has synchronized to one of the two patterns (64 bits
received without an error) at which time PBEO will go low and the PRBSD bit in the Status Register
(SR) will be set. Once synchronized, any bit errors received will cause a positive going pulse at PBEO,
synchronous with RCLK. This output can be used with external circuitry to keep track of bit error rates
during the PRBS testing. Setting CCR6.0 (ECRS) = 1 will allow the PRBS errors to be accumulated in
the 16-bit counter in registers ECR1 and ECR2. The PRBS synchronizer will remain in sync until it
experiences 6 bit errors or more within a 64-bit span. Both PRBS patterns comply with the ITU-T O.151
specifications.
6.4 Error Counter
Error Count Register 1 (ECR1) is the most significant word and ECR2 is the least significant word of a
user selectable 16-bit counter that records incoming errors including BiPolar Violations (BPV), Code
Violations (CV), Excessive Zero violations (EXZ) and/or PRBS Errors. See Table 6-3 and Table 6-4 and
Figure 1-2 for details.
Table 6-3. Definition of Received Errors
ERROR
E1 OR T1
BPV
E1/T1
CV
E1
EXZ
E1
EXZ
T1
PRBS
E1/T1
DEFINITION OF RECEIVED ERRORS
Two consecutive marks with the same polarity. Will ignore BPVs due to
HDB3 and B8ZS zero suppression when CCR2.3 = 0. Typically used with
AMI coding (CCR2.3 = 1). ITU-T O.161.
When HDB3 is enabled (CCR2.3 = 0) and the receiver detects two
consecutive BPVs with the same polarity. ITU-T O.161.
When four or more consecutive zeros are detected.
When receiving AMI coded signals (CCR2.3 = 1), detection of 16 or more
zeros or a BPV. ANSI T1.403 1999.
When receiving B8ZS coded signals (CCR2.3 = 0), detection of 8 or more
zeros or a BPV. ANSI T1.403 1999.
A bit error in a received PRBS pattern. See Section 6.3 for details. ITU-T
O.151.
47 of 76
DS21348/DS21Q348
Table 6-4. Function of ECRS Bits and RNEG Pin
E1 or T1
(CCR1.7)
0
0
0
0
1
1
1
1
X
ECRS2
(CCR6.2)
0
0
0
0
0
0
0
0
1
ECRS1
(CCR6.1)
0
0
1
1
X
X
X
X
X
ECRS0
(CCR6.0)
0
1
0
1
0
1
0
1
X
RHBE
(CCR2.3)
X
X
X
X
0
0
1
1
X
FUNCTION OF ECR
COUNTERS/RNEG1
CVs
BPVs (HDB3 code words not counted)
CVs + EXZs
BPVs + EXZs
BPVs (B8ZS code words not counted)
BPVs + 8 EXZs
BPVs
BPVs + 16 EXZs
PRBS Errors2
Note 1:
RNEG outputs error data only when in NRZ mode (CCR1.6 = 1)
Note 2:
PRBS errors will always be output at PBEO independent of ECR control bits and NRZ mode and will not be present at RNEG.
6.4.1 Error Counter Update
A transition of the ECUE (CCR1.4) control bit from 0 to 1 will update the ECR registers with the current
values and reset the counters. ECUE must be set back to zero and another 0 to 1 transition must occur for
subsequent reads/resets of the ECR registers. Note that the DS21348 can report errors at RNEG when in
NRZ mode (CCR1.6 = 1) by outputting a pulse for each error occurrence. The counter saturates at 65,535
and will not rollover.
ECR1 (11H): UPPER ERROR COUNT REGISTER 1;
ECR2 (12H): LOWER ERROR COUNT REGISTER 2
(MSB)
E15
E7
E14
E6
E13
E5
E12
E4
E11
E3
E10
E2
SYMBOL
POSITION
E15
ECR1.7
MSB of the 16-bit error count
E0
ECR2.0
LSB of the 16-bit error count
E9
E1
(LSB)
E8
E0
ECR1
ECR2
DESCRIPTION
6.5 Error Insertion
When IBPV (CCR3.1) is transitioned from a zero to a one, the device waits for the next occurrence of
three consecutive ones to insert a BPV. IBPV must be cleared and set again for another BPV error
insertion. See Figure 1-3 for details on the insertion of the BPV into the datastream.
When IBE (CCR3.0) is transitioned from a zero to a one, the device will insert a logic error. IBE must be
cleared and set again for another logic error insertion. See Figure 1-3 for details on the insertion of the
logic error into the datasteam.
48 of 76
DS21348/DS21Q348
7. ANALOG INTERFACE
7.1 Receiver
The DS21348 contains a digital clock recovery system. The DS21348 couples to the receive E1 or T1
twisted pair (or coaxial cable in 75Ω E1 applications) via a 1:1 transformer. See Table 7-3 for transformer
details. Figure 7-1, Figure 7-2, and Figure 7-3 along with Table 7-1 and Table 7-2 show the receive
termination requirements. The DS21348 has the option of using internal termination resistors.
The DS21348 is designed to be fully software-selectable for E1 and T1 without the need to change any
external resistors for the receive-side. The receive-side will allow the user to configure the DS21348 for
75Ω, 100Ω, or 120Ω receive termination by setting the RT1 (CCR5.1) and RT0 (CCR5.0) bits. When
using the internal termination feature, the Rr resistors should be 60Ω each. See Figure 7-1 for details. If
external termination is required, RT1 and RT0 should be set to 0 and both Rr resistors in Figure 7-1 will
need to be 37.5Ω, 50Ω, or 60Ω each depending on the line impedance.
The resultant E1 or T1 clock derived from the 2.048/1.544 PLL (JACLK in Figure 1-1) is internally
multiplied by 16 via another internal PLL and fed to the clock recovery system. The clock recovery
system uses the clock from the PLL circuit to form a 16 times oversampler which is used to recover the
clock and data. This oversampling technique offers outstanding performance to meet jitter tolerance
specifications shown in Figure 7-6.
Normally, the clock that is output at the RCLK pin is the recovered clock from the E1 AMI/HDB3 or T1
AMI/B8ZS waveform presented at the RTIP and RRING inputs. When no signal is present at RTIP and
RRING, a Receive Carrier Loss (RCL) condition will occur and the RCLK will be derived from the
JACLK source. See Figure 1-1. If the jitter attenuator is placed in the receive path (as is the case in most
applications), the jitter attenuator restores the RCLK to an approximate 50% duty cycle. If the jitter
attenuator is either placed in the transmit path or is disabled, the RCLK output can exhibit slightly shorter
high cycles of the clock. This is due to the highly oversampled digital clock recovery circuitry. See the
Receive AC Timing Characteristics in Section 11 for more details.
The receive-side circuitry also contains a clock synthesizer which outputs a user configurable clock (up to
16.384MHz) synthesized to RCLK at BPCLK (pin 31). See Table 4-3 for details on output clock
frequencies at BPCLK. In hardware mode, BPCLK defaults to a 16.384MHz output.
The DS21348 has a bypass mode for the receive side clock and data. This allows the BPCLK to be
derived from RCLK after the jitter attenuator while the clock and data presented at RCLK, RPOS, and
RNEG go unaltered. This is intended for applications where the receive side jitter attenuation will be
done after the LIU. Setting RJAB (CCR6.3) to a logic 1 will enable the bypass. Be sure that the jitter
attenuator is in the receive path (CCR4.3 = 0). See Figure 1-1 for details.
The DS21348 will report the signal strength at RTIP and RRING in 2.5dB increments via RL3-RL0
located in the Receive Information Register 2. This feature is helpful when trouble shooting line
performance problems. See Table 5-2 for details.
Monitor applications in both E1 and T1 require various flat gain settings for the receive-side circuitry.
The DS21348 can be programmed to support these applications via the Monitor Mode control bits MM1
and MM0. When the monitor modes are enabled, the receiver will tolerate normal line loss up to -6dB.
See Table 4-4 for details.
49 of 76
DS21348/DS21Q348
7.2 Transmitter
The DS21348 uses a set of laser-trimmed delay lines along with a precision Digital-to-Analog Converter
(DAC) to create the waveforms that are transmitted onto the E1 or T1 line. The waveforms created by the
DS21348 meet the latest ETSI, ITU, ANSI, and AT&T specifications. The user will select which
waveform is to be generated by setting the ETS bit (CCR1.7) for E1 or T1 operation, then programming
the L2/L1/L0 bits in Common Control Register 4 for the appropriate application. See Table 7-1 and
Table 7-2 for the proper L2/L1/L0 settings.
A 2.048MHz or 1.544MHz TTL clock is required at TCLK for transmitting data at TPOS and TNEG.
ITU specification G.703 requires an accuracy of ±50ppm for both T1 and E1. TR62411 and ANSI specs
require an accuracy of ±32ppm for T1 interfaces. The clock can be sourced internally by RCLK or
JACLK. See CCR1.2, CCR1.1, CCR1.0, and Figure 1-3 for details. Due to the nature of the design of the
transmitter in the DS21348, very little jitter (less than 0.005UIP-P broadband from 10Hz to 100kHz) is
added to the jitter present on TCLK. Also, the waveforms created are independent of the duty cycle of
TCLK. The transmitter in the DS21348 couples to the E1 or T1 transmit twisted pair (or coaxial cable in
some E1 applications) via a 1:2 step-up transformer. In order for the device to create the proper
waveforms, the transformer used must meet the specifications listed in Table 7-3.
The DS21348 has automatic short-circuit limiter which limits the source current to 50mA (RMS) into a
1Ω load. This feature can be disabled by setting the SCLD bit (CCR2.5) = 1. When the current limiter is
activated, TCLE (SR.2) will be set even if short circuit limiter is disabled. The TPD bit (CCR4.0) will
power-down the transmit line driver and tri-state the TTIP and TRING pins. The DS21348 can also detect
when the TTIP or TRING outputs are open circuited. When an open circuit is detected, TOCD (SR.1)
will be set.
7.3 Jitter Attenuator
The DS21348 contains an on-board jitter attenuator that can be set to a depth of either 32 or 128 bits via
the JABDS bit (CCR4.2). In hardware mode the depth is 128 bits and cannot be changed. The 128-bit
mode is used in applications where large excursions of wander are expected. The 32-bit mode is used in
delay sensitive applications. The characteristics of the attenuation are shown in Figure 7-7Figure 7-7. The
jitter attenuator can be placed in either the receive path or the transmit path by appropriately setting or
clearing the JAS bit (CCR4.3). Also, the jitter attenuator can be disabled (in effect, removed) by setting
the DJA bit (CCR4.1). For the jitter attenuator to operate properly, a 2.048MHz or 1.544MHz clock must
be applied at MCLK. ITU specification G.703 requires an accuracy of ±50ppm for both T1 and E1.
TR62411 and ANSI specs require an accuracy of ±32ppm for T1 interfaces. There is an on-board PLL for
the jitter attenuator, which will convert the 2.048MHz clock to a 1.544 MHz rate for T1 applications.
Setting JAMUX (CCR1.3) to a logic 0 bypasses this PLL. On-board circuitry adjusts either the recovered
clock from the clock/data recovery block or the clock applied at the TCLK pin to create a smooth jitterfree clock, which is used to clock data out of the jitter attenuator FIFO. It is acceptable to provide a
gapped/bursty clock at the TCLK pin if the jitter attenuator is placed on the transmit side. If the incoming
jitter exceeds either 120UIP-P (buffer depth is 128 bits) or 28UIP-P (buffer depth is 32 bits), then the
DS21348 will divide the internal nominal 32.768MHz (E1) or 24.704MHz (T1) clock by either 15 or 17
instead of the normal 16 to keep the buffer from overflowing. When the device divides by either 15 or 17,
it also sets the Jitter Attenuator Limit Trip (JALT) bit in the Receive Information Register 1 (RIR1).
50 of 76
DS21348/DS21Q348
7.4 G.703 Synchronization Signal
The DS21348 can receive a 2.048MHz square-wave synchronization clock as specified in Section 13 of
ITU G.703(10/98). To use the DS21348 in this mode, set the Receive Synchronization Clock Enable
(CCR5.3) = 1. The DS21348 can also transmit the 2.048MHz square-wave synchronization clock as
specified in Section 10 of G.703. To transmit the 2.048MHz clock, set the Transmit Synchronization
Clock Enable (CCR5.2) = 1.
Table 7-1. Line Build-Out Select for E1 in Register CCR4 (ETS = 0)
L2
L1
L0
0
0
1
1
0
0
0
0
0
1
0
1
VDD
(V)
3.3
3.3
3.3
3.3
APPLICATION
75Ω normal
120Ω normal
75Ω with high return loss
120Ω with high return loss
N
1:2
1:2
1:2
1:2
RETURN LOSS
(dB)
N.M.
N.M.
21
21
Rt (Ω)
0
0
6.2
11.6
Note: See Figure 7-1, Figure 7-2, and Figure 7-3. N.M. = Not meaningful.
Table 7-2. Line Build-Out Select for T1 in Register CCR4 (ETS = 1)
L2
L1
L0
VDD
(V)
0
0
0
3.3
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
3.3
3.3
3.3
3.3
3.3
3.3
3.3
APPLICATION
DSX-1 (0 to 133 feet)/
0dB CSU
DSX-1 (133 to 266 feet)
DSX-1 (266 to 399 feet)
DSX-1 (399 to 533 feet)
DSX-1 (533 to 655 feet)
-7.5dB CSU
-15dB CSU
-22.5dB CSU
N
RETURN LOSS
(dB)
Rt (Ω)
1:2
N.M.
0
1:2
1:2
1:2
1:2
1:2
1:2
1:2
N.M.
N.M.
N.M.
N.M.
N.M.
N.M.
N.M.
0
0
0
0
0
0
0
Note: See Figure 7-1, Figure 7-2, and Figure 7-3. N.M. = Not meaningful.
Table 7-3. Transformer Specifications for 3.3V Operation
SPECIFICATION
Turns Ratio 3.3V Applications
Primary Inductance
Leakage Inductance
Intertwining Capacitance
Transmit Transformer DC Resistance
Primary (Device Side)
Secondary
Receive Transformer DC Resistance
Primary (Device Side)
Secondary
RECOMMENDED VALUE
1:1 (receive) and 1:2 (transmit) ±2%
600µH minimum
1.0µH maximum
40pF maximum
1.0Ω maximum
2.0Ω maximum
1.2Ω maximum
1.2Ω maximum
51 of 76
DS21348/DS21Q348
Figure 7-1. Basic Interface
DS21348
Rt
Transmit
Line
TTIP
1.0µF
(nonpolarized)
Rt
VDD (21)
VSS (22)
TRING
N:1
(larger winding
toward the network)
VDD (36)
VSS (35)
RTIP
Receive
Line
RRING
MCLK
+VDD
0.1µF
0.01µF
10µF
0.1µF
10µF
2.048MHz
(this clock can also
be 1.544MHz for T1
only applications)
1:1
Rr
Rr
0.1µF
NOTES:
1) All resistor values are ±1%.
2) In E1 applications, the Rt resistors are used to increase the transmitter return loss (Table 7-1). No
return loss is required for T1 applications.
3) The Rr resistors should be set to 60Ω each if the internal receive-side termination feature is enabled.
When this feature is disabled, Rr = 37.5Ω for 75Ω or 60Ω for 120Ω E1 systems, or 50Ω for 100Ω
T1 lines.
4) See Table 7-1 and Table 7-2 for the appropriate transmit transformer turns ratio (N).
52 of 76
DS21348/DS21Q348
Figure 7-2. Protected Interface Using Internal Receive Termination
+VDD
D1
(optional)
Rp
Fuse
Rt
Transmit
Line
Fuse
TTIP
1.0µF
(nonpolarized)
S
C1
TRING
Rt
Rp
D3
N:1
(larger winding
toward the network)
DS21348
D2
D4
VDD (21)
VSS (22)
VDD (36)
VSS (35)
+VDD
0.1µF
0.01µF
10µF
68µF
0.1µF
10µF
+VDD
D6
D5
Fuse
Rp
RTIP
Receive
Line
S
Fuse
Rp
(optional)
C2
RRING
MCLK
2.048MHz
(this clock can also
be 1.544MHz for T1
only applications)
1:1
60
60 D7
D8
0.1µF
NOTES:
1. All resistor values are ±1%.
2. C1 = C2 = 0.1µF.
3. S is a 6V transient suppresser.
4. D1 to D8 are Schottky diodes.
5. The fuses are optional to prevent AC power line crosses from compromising the transformers.
6. Rp resistors exist to keep the Fuses from opening during a surge. If they are used, then the 60Ω
receive termination resistance must be adjusted to match the line impedance.
7. The Rt resistors are used to increase the transmitter return loss (Table 7-1). No return loss is required
for T1 applications.
8. The transmit transformer turns ratio (N) would be 1:2 for 3.3V operation.
9. The 68µF is used to keep the local power plane potential within tolerance during a surge.
53 of 76
DS21348/DS21Q348
Figure 7-3. Protected Interface Using External Receive Termination
+VDD
D1
(optional)
Rp
Fuse
Rt
Transmit
Line
D3
N:1
(larger winding
toward the network)
Fuse
Rp
Fuse
Rp
C1
TRING
Rt
Rp
D4
470
RTIP
Receive
Line
(optional)
RRING
470
1:1
Rr
DS21348
TTIP
1.0µF
(nonpolarized)
S
Fuse
D2
VDD (21)
VSS (22)
VDD (36)
VSS (35)
MCLK
+VDD
0.1µF
0.01µF
10µF
68µF
0.1µF
10µF
2.048MHz
(this clock can also
be 1.544MHz for T1
only applications)
Rr
0.1µF
NOTES:
1.
2.
3.
4.
5.
6.
All resistor values are ±1%.
C1 = 0.1µF.
S is a 6V transient suppresser.
D1 to D4 are Schottky diodes.
The fuses are optional to prevent AC power line crosses from compromising the transformers.
Rp resistors exist to keep the Fuses from opening during a surge. If they are used, then Rr must be
adjusted to match the line impedance.
7. Rr = 37.5Ω for 75Ω or 60Ω for 120Ω E1 systems, or 50Ω for 100Ω T1 lines.
8. The Rt resistors are used to increase the transmitter return loss (Table 7-1). No return loss is required
for T1 applications.
9. The transmit transformer turns ratio (N) would be 1:2 for 3.3V operation.
10. The 68µF is used to keep the local power plane potential within tolerance during a surge.
54 of 76
DS21348/DS21Q348
Figure 7-4. E1 Transmit Pulse Template
1.2
1.1
269ns
SCALED AMPLITUDE
(in 75 ohm systems, 1.0 on the scale = 2.37Vpeak
in 120 ohm systems, 1.0 on the scale = 3.00Vpeak)
1.0
0.9
0.8
0.7
G.703
Template
194ns
0.6
0.5
219ns
0.4
0.3
0.2
0.1
0
-0.1
-0.2
-250
-200
-150
-100
-50
0
TIME (ns)
55 of 76
50
100
150
200
250
DS21348/DS21Q348
Figure 7-5. T1 Transmit Pulse Template
1.2
MAXIMUM CURVE
UI
Time Amp.
1.1
1.0
-0.77
-0.39
-0.27
-0.27
-0.12
0.00
0.27
0.35
0.93
1.16
0.9
0.8
NORMALIZED AMPLITUDE
0.7
0.6
-500
-255
-175
-175
-75
0
175
225
600
750
0.05
0.05
0.80
1.15
1.15
1.05
1.05
-0.07
0.05
0.05
0.5
MINIMUM CURVE
UI
Time Amp.
-0.77
-0.23
-0.23
-0.15
0.00
0.15
0.23
0.23
0.46
0.66
0.93
1.16
-500
-150
-150
-100
0
100
150
150
300
430
600
750
-0.05
-0.05
0.50
0.95
0.95
0.90
0.50
-0.45
-0.45
-0.20
-0.05
-0.05
0.4
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
T1.102/87, T1.403,
CB 119 (Oct. 79), &
I.431 Template
-0.4
-0.5
-500 -400 -300
-200 -100
0
100
200
TIME (ns)
56 of 76
300
400
500
600
700
DS21348/DS21Q348
Figure 7-6. Jitter Tolerance
UNIT INTERVALS (UIP-P)
1k
100
DS21348
TR 62411 (Dec. 90)
Tolerance
10
ITU-T G.823
1
0.1
1
10
100
1k
FREQUENCY (Hz)
10k
100k
Figure 7-7. Jitter Attenuation
ITU G.7XX
Prohibited Area
TBR12
Prohibited
Area
-20dB
C
ur
ve
A
E1
T1
TR 62411 (Dec. 90)
Prohibited Area
-40dB
Cu
B
rve
JITTER ATTENUATION (dB)
0dB
-60dB
1
10
100
1K
FREQUENCY (Hz)
57 of 76
10K
100K
DS21348/DS21Q348
8. DS21Q348 QUAD LIU
The DS21Q348 is a quad version of the DS21348G utilizing CSBGA on carrier packaging technology.
The four LIUs are controlled via the parallel port mode. Serial and hardware modes are unavailable in
this package.
Table 8-1. DS21Q348 Pin Assignment
PIN
I/O
J1
K3
J2
H1
K2
K1
L1
H11
H12
G12
J10
H10
G11
J9
E3
D4
F3
D5
G4
K9
K7
L9
J6
L7
M8
M12
J3
D3
D10
K10
K5
G3
E10
K8
L6
D7
I
I
I
I
I
I/O
I
I
I
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I/O
I
I
I
I
I
I
I
I
I
I
O
O
O
O
O
O
PARALLEL
PORT MODE
Connect to VSS
Connect to VSS
RD (DS)
WR (R/W)
ALE (AS)
A4
A3
A2
A1
A0
D7/AD7
D6/AD6
D5/AD5
D4/AD4
D3/AD3
D2/AD2
D1/AD1
D0/AD0
VSM
INT
TEST
HRST
MCLK
BIS0
BIS1
PBTS
CS1
CS2
CS3
CS4
PBEO1
PBEO2
PBEO3
PBEO4
RCL/LOTC1
RCL/LOTC2
58 of 76
DS21348/DS21Q348
PIN
I/O
F9
J7
A1
A4
A7
A10
B2
B5
B8
B11
H4
D6
F10
L8
A2
A5
A8
A11
B3
B6
B9
B12
K4
E1
D11
K11
G2
E2
F11
M10
H3
F1
E11
L11
G1
F2
E12
M11
H2
M1
D12
K12
M2
L2
O
O
I
I
I
I
I
I
I
I
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
I
I
I
I
I
I
I
I
I
I
PARALLEL
PORT MODE
RCL/LOTC3
RCL/LOTC4
RTIP1
RTIP2
RTIP3
RTIP4
RRING1
RRING2
RRING3
RRING4
BPCLK1
BPCLK2
BPCLK3
BPCLK4
TTIP1
TTIP2
TTIP3
TTIP4
TRING1
TRING2
TRING3
TRING4
RPOS1
RPOS2
RPOS3
RPOS4
RNEG1
RNEG2
RNEG3
RNEG4
RCLK1
RCLK2
RCLK3
RCLK4
TPOS1
TPOS2
TPOS3
TPOS4
TNEG1
TNEG2
TNEG3
TNEG4
TCLK1
TCLK2
59 of 76
DS21348/DS21Q348
PIN
I/O
F12
L12
J5
D2
G9
M9
L5
E4
D8
J8
J4
D1
E9
L10
M4
F4
D9
H9
I
I
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PARALLEL
PORT MODE
TCLK3
TCLK4
VDD1
VDD2
VDD3
VDD4
VDD1
VDD2
VDD3
VDD4
VSS1
VSS2
VSS3
VSS4
VSS1
VSS2
VSS3
VSS4
60 of 76
DS21348/DS21Q348
Figure 8-1. 144-CSBGA (17mm x 17mm) Pinout
1
2
3
4
5
6
7
8
9
10
11
12
A
RTIP1
TTIP1
NC
RTIP2
TTIP2
NC
RTIP3
TTIP3
NC
RTIP4
TTIP4
NC
B
NC
C
NC
NC
NC
D
VSS2
VDD2
CS2
E
RPOS2
RNEG2 D3/AD3
VDD2
NC
F
RCLK2
TPOS2
D1/AD1
VSS2
G
TPOS1
RNEG1
PEBO2
VSM
H
WR
(R/W)
TNEG1
RCLK1 BPCLK1
J
(Note 2)
RD
(DS)
K
A4
L
A3
TCLK2
NC
M
TNEG2
TCLK1
NC
RRING1 TRING1
CS1
NC
NC
RRING2 TRING2
NC
NC
NC
RRING3 TRING3
NC
RRING4 TRING4
NC
NC
NC
NC
NC
NC
RCL/
LOTC2
VDD3
VSS3
CS3
RPOS3
TNEG3
NC
NC
NC
VSS3
PEBO3
RCLK3
TPOS3
NC
NC
NC
NC
RCL/
BPCLK3 RNEG3
LOTC3
TCLK3
NC
NC
NC
NC
VDD
3
NC
D5/AD5
A0
NC
NC
NC
NC
VSS4
D6/AD6
A2
A1
VDD1
MCLK
RCL/
LOTC4
VDD4
D4/AD4 D7/AD7
NC
NC
PEBO1
NC
TEST
PEBO4
INT
CS4
RPOS4
TNEG4
NC
VDD1
RCL/
LOTC1
BIS0
BPCLK4
HRST
VSS4
RCLK4
TCLK4
VSS1
NC
NC
NC
BIS1
VDD4
RNEG4
TPOS4
PBTS
D2/AD2 D0/AD0 BPCLK2
VSS1
ALE (AS) (Note 2) RPOS1
Note 1: Shaded areas are signals common to all four devices.
Note 2: Connect to VSS.
61 of 76
DS21348/DS21Q348
9. DC CHARACTERISTICS
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Pin Relative to Ground……………………………………………..-1.0V to +6.0V
Operating Temperature Range for DS21348TN……………………………………………-40°C to +85°C
Storage Temperature Range……………………………………………………………….-55°C to +125°C
Soldering Temperature………………………………………….See IPC/JEDEC J-STD-020 Specification
This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operation
sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time can affect device
reliability.
Table 9-1. Recommended DC Operating Conditions
(TA = -40°C to +85°C)
PARAMETER
Logic 1
Logic 0
Supply for 3.3V Operation
SYMBOL
VIH
VIL
VDD
MIN
2.0
–0.3
3.135
TYP
MAX
5.5
+0.8
3.465
UNITS
V
V
V
NOTES
MIN
TYP
5
7
MAX
UNITS
pF
pF
NOTES
TYP
MAX
+1.0
1.0
NOTES
3
4
66
100
UNITS
µA
µA
mA
mA
mA
3.3
1
Table 9-2. Capacitance
(TA = +25°C)
PARAMETER
Input Capacitance
Output Capacitance
SYMBOL
CIN
COUT
Table 9-3. DC Characteristics
(VDD = 3.3V ± 5%, TA = -40°C to +85°C.)
PARAMETER
SYMBOL
MIN
Input Leakage
IIL
-1.0
Output Leakage
ILO
Output Current (2.4V)
IOH
–1.0
Output Current (0.4V)
IOL
+4.0
Supply Current
IDD
NOTES:
1) Applies to VDD.
2) TCLK = MCLK = 2.048MHz.
3) 0.0V < VIN < VDD.
4) Applied to INT when tri-stated.
5) Power dissipation with TTIP and TRING driving a 30Ω load, for an all-ones data density.
62 of 76
2, 5
DS21348/DS21Q348
10.
THERMAL CHARACTERISTICS
Table 10-1. Thermal Characteristics—DS21Q348 CSBGA Package
PARAMETER
Ambient Temperature
Junction Temperature
Theta-JA (θJA) in Still Air
Theta-JC (θJC) in Still Air
MIN
-40ºC
TYP
+24ºC/W
+4.1ºC/W
MAX
+85ºC
+125ºC
NOTES
1
2
3
NOTES:
1) The package is mounted on a four-layer JEDEC-standard test board.
2) Theta-JA (θJA) is the junction to ambient thermal resistance, when the package is mounted on a fourlayer JEDEC-standard test board.
3) While Theta-JC (θJC) is commonly used as the thermal parameter that provides a correlation between the
junction temperature (Tj) and the average temperature on top center of four of the chip-scale BGA
packages (TC), the proper term is Psi-JT. It is defined by:
(TJ - TC) / overall package power
The method of measurement of the thermal parameters is defined in EIA/JEDEC-standard document
EIA-JESD51-2.
Table 10-2. Theta-JA (θJA) vs. Airflow
FORCED AIR (m/s)
0
1
2.5
THETA-JA (θJA)
24ºC/W
21ºC/W
19ºC/W
63 of 76
DS21348/DS21Q348
11.
AC CHARACTERISTICS
Table 11-1. AC Characteristics—Multiplexed Parallel Port (BIS1 = 0, BIS0 = 0)
(VDD = 3.3V ± 5%, TA = -40°C to +85°C.) (See Figure 11-1, Figure 11-2, and Figure 11-3.)
PARAMETER
SYMBOL
MIN
tCYC
200
ns
Pulse Width, DS Low or RD
High
PWEL
100
ns
Pulse Width, DS High or RD
Low
PWEH
100
ns
Input Rise/Fall Times
tR, tF
R/W Hold Time
tRWH
10
ns
R/W Setup Time Before DS
High
tRWS
50
ns
CS Setup Time Before DS,
WR, or RD Active
tCS
20
ns
CS Hold Time
tCH
0
ns
Read Data Hold Time
tDHR
10
Write Data Hold Time
tDHW
0
ns
Muxed Address Valid to AS
or ALE Fall
tASL
15
ns
Muxed Address Hold Time
tAHL
10
ns
tASD
20
ns
PWASH
30
ns
tASED
10
ns
tDDR
20
tDSW
50
Cycle Time
Delay Time DS, WR, or RD
to AS or ALE Rise
Pulse Width AS or ALE
High
Delay Time, AS or ALE to
DS, WR, or RD
Output Data Delay Time
from DS or RD
Data Setup Time
TYP
MAX
20
64 of 76
50
80
UNITS
ns
ns
ns
ns
NOTES
DS21348/DS21Q348
Figure 11-1. Intel Bus Read Timing (PBTS = 0, BIS1 = 0, BIS0 = 0)
t CYC
ALE
WR
PWASH
t ASD
t ASD
RD
PWEL
t ASED
PWEH
t CH
t CS
CS
t ASL
AD0-AD7
t DHR
t DDR
t AHL
Figure 11-2. Intel Bus Write Timing (PBTS = 0, BIS1 = 0, BIS0 = 0)
t CYC
ALE
RD
WR
PWASH
t ASD
t ASED
t ASD
PWEL
PWEH
t CH
t CS
CS
AD0-AD7
t ASL
t DHW
t AHL
65 of 76
t DSW
DS21348/DS21Q348
Figure 11-3. Motorola Bus Timing (PBTS = 1, BIS1 = 0, BIS0 = 0)
PWASH
AS
DS
PWEH
t ASED
t ASD
PWEL
t CYC
t RWS
t RWH
R/W
AD0-AD7
(read)
t DDR
t ASL
t AHL
t DHR
t CH
t CS
CS
AD0-AD7
(write)
t DSW
t ASL
t DHW
t AHL
66 of 76
DS21348/DS21Q348
Table 11-2. AC Characteristics—Nonmultiplexed Parallel Port
(BIS1 = 0, BIS0 = 1)
(VDD = 3.3V ± 5%, TA = -40°C to +85°C.) (See Figure 11-4, Figure 11-5, Figure 11-6, and
Figure 11-7.)
PARAMETER
Setup Time for A0 to A4, Valid to CS
Active
SYMBOL
MIN
t1
0
ns
Setup Time for CS Active to Either RD,
WR, or DS Active
t2
0
ns
Delay Time from Either RD or DS Active
to Data Valid
t3
Hold Time from Either RD, WR, or DS,
Inactive to CS Inactive
t4
0
Hold Time from CS Inactive to Data Bus
Tri-State
t5
5
t6
75
ns
t7
10
ns
t8
10
ns
t9
10
ns
Wait Time from Either WR or DS Active
to Latch Data
Data Setup Time to Either WR or DS
Inactive
Data Hold Time from Either WR or DS
Inactive
Address Hold from Either WR or DS
Inactive
67 of 76
TYP
MAX
75
UNITS
ns
ns
20
ns
NOTES
DS21348/DS21Q348
Figure 11-4. Intel Bus Read Timing (PBTS = 0, BIS1 = 0, BIS0 = 1)
Address Valid
A0 to A4
D0 to D7
Data Valid
t5
5ns min/20ns max
WR
CS
t1
0ns min.
0ns min.
t2
RD
t3
75ns max.
t4
0ns min.
Figure 11-5. Intel Bus Write Timing (PBTS = 0, BIS1 = 0, BIS0 = 1)
Address Valid
A0 to A4
D0 to D7
t7
RD
t1
CS
0ns min.
WR
10ns
min.
t8
10ns
min.
0ns min.
t2
t6
75ns min.
68 of 76
t4
0ns min.
DS21348/DS21Q348
Figure 11-6. Motorola Bus Read Timing (PBTS = 1, BIS1 = 0, BIS0 = 1)
Address Valid
A0 to A4
Data Valid
D0 to D7
5ns min. / 20ns max.
R/W
t1
CS
t5
0ns min.
0ns min.
t2
t3
t4
0ns min.
75ns max.
DS
Figure 11-7. Motorola Bus Write Timing (PBTS = 1, BIS1 = 0, BIS0 = 1)
Address Valid
A0 to A4
D0 to D7
10ns
min.
R/W
t1
CS
0ns min.
DS
t7 t8
10ns
min.
0ns min.
t2
t6
75ns min.
69 of 76
t4
0ns min.
DS21348/DS21Q348
Table 11-3. AC Characteristics—Serial Port (BIS1 = 1, BIS0 = 0)
(VDD = 3.3V ± 5%, TA = -40°C to +85°C.) (See Figure 11-8.)
PARAMETER
SYMBOL
MIN
tCSS
tSSS
tSSH
tSLH
tSRF
tLSC
tCM
tSSV
tSSH
tCSH
50
50
50
200
Setup Time CS to SCLK
Setup Time SDI to SCLK
Hold Timfe SCLK to SDI
SCLK High/Low Time
SCLK Rise/Fall Time
SCLK to CS Inactive
CS Inactive Time
SCLK to SDO Valid
SCLK to SDO Tri-State
CS Inactive to SDO Tri-State
TYP
MAX
UNITS
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
50
50
250
50
100
100
Figure 11-8. Serial Bus Timing (BIS1 = 1, BIS0 = 0)
tCM
CS
tSRF
tCSS
SCLK
tLSC
tSLH
1
SCLK2
SDI
tSSS
tSSH
LSB
tCSH
MSB
LSB
MSB
tSSV
SDO
HIGH Z
LSB
NOTE 1: OCES =1 AND ICES = 0.
NOTE 2: OCES = 0 AND ICES = 1.
70 of 76
tSSH
MSB
HIGH Z
NOTES
DS21348/DS21Q348
Table 11-4. AC Characteristics—Receive Side
(VDD = 3.3V ± 5%, TA = -40°C to +85°C.) (See Figure 11-9.)
PARAMETER
SYMBOL
MIN
TYP
RCLK Period
tCP
RCLK Pulse Width
RCLK Pulse Width
Delay RCLK to RPOS, RNEG,
PBEO, RBPV Valid
MAX
UNITS
NOTES
488
ns
1
648
ns
2
tCH
200
ns
3
tCL
tCH
200
150
ns
ns
3
4
tCL
150
ns
4
tDD
50
ns
NOTES:
1) E1 mode.
2) T1 or J1 mode.
3) Jitter attenuator enabled in the receive path.
4) Jitter attenuator disabled or enabled in the transmit path.
Figure 11-9. Receive Side Timing
RCLK1
t CL
RCLK2
t CH
t CP
t DD
RPOS, RNEG
PBEO
bit
error
PRBS Detector Out of Sync
t DD
RNEG3
BPV/
EXZ/
CV
BPV/
EXZ/
CV
NOTE 1: RCES = 1 (CCR2.0) OR CES = 1.
NOTE 2: RCES = 0 (CCR2.0) OR CES = 0.
NOTE 3: RNEG IS IN NRZ MODE (CCR1.6 = 1).
71 of 76
DS21348/DS21Q348
Table 11-5. AC Characteristics—Transmit Side
(VDD = 3.3V ± 5%, TA = -40°C to +85°C.) (Figure 11-10)
PARAMETER
SYMBOL
MIN
TCLK Period
tCP
TCLK Pulse Width
tCH
tCL
75
75
UNITS
ns
ns
ns
ns
TPOS/TNEG Setup to TCLK
Falling or Rising
tSU
20
ns
TPOS/TNEG Hold from TCLK
Falling or Rising
tHD
20
ns
TCLK Rise and Fall Times
TYP
488
648
MAX
tR, tF
25
NOTES:
1) E1 mode.
2) T1 or J1 mode.
Figure 11-10. Transmit Side Timing
t CP
tR
t CL
tF
TCLK1
TCLK2
t SU
TPOS, TNEG
t HD
NOTE 1: TCES = 0 (CCR2.1) or CES = 0.
NOTE 2: TCES = 1 (CCR2.1) or CES = 1.
72 of 76
t CH
ns
NOTES
1
2
DS21348/DS21Q348
12.
PACKAGE INFORMATION
(The package drawing(s) in this data sheet may not reflect the most current specifications. The package number provided for
each package is a link to the latest package outline information.)
12.1 44-Pin TQFP (56-G4012-001)
SUGGESTED PAD LAYOUT
44 PIN TQFP, 10*10*1.0
SEE DETAIL "A"
DIMENSIONS ARE IN MILLIMETERS
73 of 76
DS21348/DS21Q348
12.2 49-Ball CSGBA (7mm x 7mm) (56-G6006-001)
74 of 76
DS21348/DS21Q348
12.3 144-Ball CSBGA (17mm x 17mm) (56-G6011-001)
A1 CORNER
3
A1 CORNER
12 11 10
9
8
7
6
5
17.00
13.97
0.20
1.52
17.00
4X
1.27
X
13.97
1.52
DETAIL A
0.05
2.6
0
1.99
0.76
Z
DETAIL B
75 of 76
3
2 1
A B C D E F G H I J K L
1.27
Y
4
0.6
0.5
DS21348/DS21Q348
SOLDER BALL
φ 0.76 REF
φ 0.76
L
X
φ 0.76
L
Z
Y
Z
0.05 LABEL THICKNESS
//
0.24
Z
2.60
REF
0.17
//
Z
0.10
SEATING PLANE
2
0.76
REF
Z
76 of 76
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.
No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2006 Maxim Integrated Products • Printed USA
are registered trademarks of Maxim Integrated Products, Inc., and Dallas Semiconductor Corporation.
工商网监
湘ICP备2023018690号
