EV-ADF5901SD2Z

EV-ADF5901SD2Z Evaluation Board User Guide UG-864 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluating the ADF5901 24 GHz Voltage Controlled Oscillator (VCO) and Programmable Gain Amplifier (PGA) with a 2-Channel Power Amplifier (PA) Output FEATURES GENERAL DESCRIPTION Contains ADF5901 24 GHz VCO and PGA with a 2-channel PA output Contains ADF4159 13 GHz fractional-N frequency synthesizer Accompanying software allows control of the ADF5901 and the ADF4159 functions from a PC The EV-ADF5901SD2Z evaluation board allows the user to evaluate the performance of the ADF5901 24 GHz VCO and PGA with a 2-channel PA output. Figure 1 shows the EV-ADF5901SD2Z, which contains the ADF5901, the ADF4159, three high frequency, K-type SMA connectors for the local oscillator (LO) output and two transceiver (Tx) outputs, two high frequency SMA connectors for the AUX and the AUX outputs, banana connectors for power supply, and a connector for the serial interface. EVALUATION KIT CONTENTS EV-ADF5901SD2Z evaluation board ADDITIONAL EQUIPMENT PC running Windows® XP or more recent version Analog Devices, Inc., EVAL-SDP-CS1Z system demonstration platform serial (SDP-S) board Spectrum analyzer Oscilloscope (optional) 5 V power supply The EV-ADF5901SD2Z evaluation kit also contains software that is compatible with Windows XP and later versions to allow easy programming of the device. The EV-ADF5901SD2Z evaluation board requires an EVALSDP-CS1Z (SDP-S) controller board, which is not supplied with the kit. The EVAL-SDP-CS1Z allows software programming of the ADF5901 device. DOCUMENTS NEEDED ADF5901 data sheet Full specifications on the ADF5901 are available in the ADF5901 data sheet, which should be consulted in conjunction with this user guide when working with the evaluation board. REQUIRED SOFTWARE Analog Devices ADF5901 software 13381-001 EV-ADF5901SD2Z EVALUATION BOARD PICTURE Figure 1. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 18 UG-864 EV-ADF5901SD2Z Evaluation Board User Guide TABLE OF CONTENTS Features .............................................................................................. 1  Input Signals...................................................................................3  Evaluation Kit Contents ................................................................... 1  Output Signals ...............................................................................3  Additional Equipment ..................................................................... 1  Default Operation .........................................................................3  Documents Needed .......................................................................... 1  Evaluation Board Quick Start Procedures .....................................4  Required Software ............................................................................ 1  EV-ADF5901SD2Z Control Software.........................................4  General Description ......................................................................... 1  Evaluation and Testing......................................................................8  EV-ADF5901SD2Z Evaluation Board Picture .............................. 1  Evaluation Board Schematics and Artwork ...................................9  Revision History ............................................................................... 2  Ordering Information .................................................................... 17  Evaluation Board Hardware ............................................................ 3  Bill of Materials ........................................................................... 17  Power Supplies .............................................................................. 3  Related Links ............................................................................... 18  REVISION HISTORY 12/15—Revision 0: Initial Version Rev. 0 | Page 2 of 18 EV-ADF5901SD2Z Evaluation Board User Guide UG-864 EVALUATION BOARD HARDWARE The EV-ADF5901SD2Z evaluation board requires the use of an EVAL-SDP-CS1Z (SDP-S) controller board to program the device. The EVAL-SDP-CS1Z is not included and must be purchased separately. The EV-ADF5901SD2Z schematics are shown in Figure 7 to Figure 14. The EV-ADF5901SD2Z evaluation board layout is shown in Figure 15 and Figure 16. POWER SUPPLIES The EV-ADF5901SD2Z board is powered via a 5 V external supply that must be connected as described in the Evaluation Board Quick Start Procedures section. INPUT SIGNALS Control VTUNE from the ADF4159. Alternatively, control VTUNE externally via J7 by removing R20 and powering down the ADF4159. OUTPUT SIGNALS The Tx and LO outputs from the ADF5901 contain dc bias voltage and are available on the J8 (TXOUT1), J9 (TXOUT2) and J4 (LOOUT) output SMAs. DEFAULT OPERATION All the necessary components to operate the ADF5901 are included on the EV-ADF5901SD2Z. The 100 MHz temperature controlled crystal oscillator (TCXO) provides the necessary reference signal. An external REFIN can be used, if desired. Rev. 0 | Page 3 of 18 UG-864 EV-ADF5901SD2Z Evaluation Board User Guide EVALUATION BOARD QUICK START PROCEDURES Take the following steps to evaluate the ADF5901: EV-ADF5901SD2Z CONTROL SOFTWARE 1. The control software for the EV-ADF5901SD2Z accompanies the EV-ADF5901SD2Z on a CD. For software installation procedures, follow the on-screen instructions. To run the EV-ADF5901SD2Z control software, take the following steps: 1. Choose the ADF5901 and ADF4159 file on the desktop or in the Start menu. 2. Within the Select Device and Connection tab, choose your device and your connection method, and click Connect. 3. Confirm that Analog Devices Eval Board connected displays at the bottom left of the window. Otherwise, the software has no connection to the EV-ADF5901SD2Z evaluation board. Note that when connecting the EV-ADF5901SD2Z, it takes approximately 5 sec to 10 sec for the status label to change. 13381-002 Connect the power supply to the EV-ADF5901SD2Z: a. 5 V to the Banana Connector P3 b. GND to the Banana Connector P2. 2. Install the ADF5901 software by following the on-screen instructions. 3. Connect the EVAL-SDP-CS1Z controller board to the PC and to the EV-ADF5901SD2Z. 4. Install the hardware driver; follow the on-screen instructions. 5. Run the ADF5901 software. 6. Choose ADF5901 and ADF4159 and SDP board (black) in the Select Device and Connection tab of the software front panel window (see Figure 2). 7. Ensure that a SDP board connected message appears on the front panel (see Figure 2). 8. Connect an ac-coupled signal source analyzer to the TX2 output SMA, J9. 9. Click the ADF5901 Controls tab and click Write All Registers (see Figure 4). 10. Click the ADF5901 Controls tab and click Initialize ADF5901 (see Figure 3). 11. Measure the result on TXOUT2 (J9). Figure 2. Software Front Panel Display—Select Device and Connection Rev. 0 | Page 4 of 18 EV-ADF5901SD2Z Evaluation Board User Guide To control the ADF5901 settings (see Figure 3), select the ADF5901 Controls tab. Use the register section within the ADF5901 Controls tab to select from the general options available for the ADF5901, including calibration control and register read back. At initial power-up of the device, click Initialize ADF5901 to perform the initialization sequence as described in the ADF5901 data sheet. Following the sequence, the ADF5901 powers up, and all the ADF5901 blocks calibrate. 13381-003 To set the calibration frequency for the ADF5901, go to the RF Settings section shown in Figure 3 under the ADF5901 Controls tab. Set the frequency to the center of the frequency band. Type the desired output frequency in the VCO Frequency text box (in MHz). UG-864 Figure 3. Software Front Panel Display—ADF5901 Controls Rev. 0 | Page 5 of 18 UG-864 EV-ADF5901SD2Z Evaluation Board User Guide To control the ADF4159 settings (see Figure 4), select the ADF4159 Controls tab. Use the Muxout drop-down box within the Main Controls tab to choose the signal connected to the output of the MUXOUT pin. Click the button under each register value within the Main Controls tab to write that value to the device. The register values are shown in Figure 4 at the bottom of the window. When the background of a register value is green, this indicates that the value was changed and needs to be written to the device. 13381-004 Within the ADF4159 Controls tab, select the Main Controls tab to set the RF Settings and PLL Settings. In the RF Settings area, set the RF VCO Output Frequency to half the ADF5901 VCO output. In addition, set the Reference Frequency the same as the applied reference signal. Calculate the PFD frequency from the reference frequency, the R counter, the reference doubler, and the reference divide by 2. Ensure that the value in the PFD Frequency box matches the value specified in the loop filter design. In the PLL Settings area, program the Charge Pump Setting to the value for which the loop filter was designed. Program the Phase Detector Polarity to negative when using an inverting active loop filter configuration. (Note that a passive loop filter was used on this evaluation board). Figure 4. Software Front Panel Display—ADF4159 Controls Rev. 0 | Page 6 of 18 EV-ADF5901SD2Z Evaluation Board User Guide To configure the ramp functionality of the ADF4159, select the Ramps and Shift Keying tab. To select the ramp type, go to the Ramp mode drop-down box within the Ramps and Shift Keying tab, and set the various ramp parameters in the CLK1 box and Up Ramp boxes. Example ADF5901 Tx output with a ramp time of 5 ms. For 200 MHz, the PLL is programmed for a 100 MHz ramp because the EV-ADF5901SD2Z uses the ADF5901 auxilary output with a 12 GHz output signal. After each parameter is set in the software, it must be written to the device. To configure the other options in the Ramps and Shift Keying tab, set the various Ramp and Shift Keying controls of the ADF4159. 13381-005 Figure 5 shows the ramping settings for an example of a continuous triangular ramp of 1000 up ramp steps over 200 MHz at the UG-864 Figure 5. Software Front Panel Display—ADF4159 Ramps and Shift Keying Rev. 0 | Page 7 of 18 UG-864 EV-ADF5901SD2Z Evaluation Board User Guide EVALUATION AND TESTING To evaluate and test the performance of the ADF5901, take the following steps: 2. 1. 3. Follow the on-screen instructions to install the ADF5901 evaluation software. Connect the EVAL-SDP-CS1Z controller board to the EV-ADF5901SD2Z. Connect dc blocked J9 (TXOUT2) to the spectrum analyzer. Click the ADF5901 icon to run the ADF5901 software. 5. 6. 7. Select the USB board and the ADF5901 device in the Select Device and Connection tab of the software front panel window (see Figure 2). In the ADF4159 Main Controls tab, click Write All Registers to power up the ADF4159. In the ADF5901 Controls tab, click Initialize ADF5901 to power up and calibrate the ADF5901. See Figure 6 for the suggested setup. Measure the TXOUT2 output signal on the J9 SMA. +5V POWER SUPPLY SDP-S ADAPTOR BOARD SPECTRUM ANALYZER PC 13381-006 1. 4. BLOCKING CAPACITOR Figure 6. Typical EV-ADF5901SD2Z Evaluation Board Setup Rev. 0 | Page 8 of 18 Figure 7. EV-ADF5901SD2Z Schematic (Page 1) Rev. 0 | Page 9 of 18 GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 AUXB AUX SDP SPI_CLK SPI_MISO SPI_MOSI SDP REFIN R4 0 TP16 1 SPI_CLK SPI_MISO SPI_MOSI SPI_CLK SPI_MOSI SPI_MISO RFINA RFINB REFIN CE CLK DATA LE TXDATA DVDD R7 0 VP AVDD R5 0 CP AGND TP17 1 AGND SPI SIGNALS CLK_PLL DATA_PLL LE_PLL CE_PLL TX_DATA MUXOUT_PLL CLK_TX DATA_TX LE_TX DOUT_TX CE_TX CPOUT MUXOUT_PLL CLK_TX SPI_CLK DATA_TX SPI_MOSI LE_TX SPI_MISO DOUT_TX GPIO0 CE_TX GPIO1 GPIO2 SPI_CON CLK_PLL GPIO3 DATA_PLL GPIO4 LE_PLL GPIO5 CE_PLL GPIO6 TX_DATA GPIO7 MUXOUT_PLL ADF4159 ADF4159_PLL MUXOUT AVDD_TX CE_PLL CLK_PLL DATA_PLL LE_PLL TX_DATA DVDD_PLL TP3 CPOUT 571-0500 571-0100 P3 P2 142-0701-851 AGND 1 REF_IN VSUPPLY AGND LOOP FILTER CPOUT LFP VTUNE J1 AGND 142-0701-851 TP18 DNI AGND AVDD_TX AVDD_PLL DVDD_PLL AGND VTUNE REFIN CE_TX CLK_TX DATA_TX LE_TX REFERENCE REFIN AVDD REF_CLK REF POWER MANAGEMENT POWER VSUPPLY AVDD_PLL VTUNE TBD0603 TBD0603 C42 DNI C37 TBD1206 C33 DNI TP20 REFIN AVDD_TX AVDD_PLL DVDD_PLL VTUNE REFIN CE CLK DATA LE AVDD_TX 0 J7 0 R8 LO_OUT AUX AUXB ADF5901 ATEST MUXOUT DOUT ADF5901_TXTX_OUT1 TX_OUT2 AHI R9 TX_AHI DVDD_PLL TP4 AVDD_TX TP5 DVDD_PLL TP22 R3 R10 0 VCO_AHI AVDD_PLL TP23 AUX AUXB LO MUX_TX 1 DOUT_TX TP24 ATEST_TX TX_OUT1 TX_OUT2 1 AGND AGND 5 4 3 2 J9 AGND AGND J4 1 AGND 3 2 LO OUTPUT 02K243-40M LO TX OUTPUTS 02K243-40M TX_OUT2 1 5 4 3 2 J8 02K243-40M TX_OUT1 J3 J2 AUX OUTPUTS 142-0761-801 AUXB 142-0761-801 AUX EV-ADF5901SD2Z Evaluation Board User Guide UG-864 EVALUATION BOARD SCHEMATICS AND ARTWORK TP21 13381-007 0 UG-864 EV-ADF5901SD2Z Evaluation Board User Guide J5 AGND OUT GPIO0 GPIO2 OUT GPIO4 OUT OUT GPIO6 AGND R36 R6 100K TBD0603 FX8-120S-SV(21) R35 100K 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 DNI 8 U3 A0 VCC EEPROM A1 5 A2 SDA SCL WP VSS 4 24LC32A-I/MS VIO 1 2 3 6 7 AGND OUT OUT OUT SPI_MOSI SPI_MISO SPI_CLK GPIO1 OUT GPIO3 OUT GPIO5 OUT GPIO7 OUT FX8-120S-SV(21) Figure 8. EV-ADF5901SD2Z Schematic (Page 2) Rev. 0 | Page 10 of 18 13381-008 J5 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 EV-ADF5901SD2Z Evaluation Board User Guide UG-864 DNI R19 R20 TBD0805 0 DNI OUT TBD0805 C14 TBD0805 C13 VTUNE 13381-009 TBD0805 R18 DNI C12 TBD0805 DNI DNI CPOUT IN AGND Figure 9. EV-ADF5901SD2Z Schematic (Page 3) 0 600OHM Y1 4 1 E/D VDDOUT 3 GND 2 CWX823-100.0MHZ 1 R43 91 REF OUT AGND TBD0603 DNI R42 10PF AGND IN REFIN R45 0 Figure 10. EV-ADF5901SD2Z Schematic (Page 4) Rev. 0 | Page 11 of 18 13381-010 C41 22UF C40 10K TP36 R41 1 E1 2 R40 AVDD IO UG-864 EV-ADF5901SD2Z Evaluation Board User Guide TP32 1 OUT 1UF C36 0 R27 C32 AVDD_TX 0 AGND TP34 U4 1 0 R29 3 5 1 R2 AVDD_PLL EN VOUT 0 NC GND 4 2 ADP150AUJZ-3.3-R7 C38 C34 0 VIN OUT 1UF R25 AGND TP35 U5 0 3 1 DVDD_PLL R32 5 VOUT EN 0 NC GND 4 2 ADP150AUJZ-3.3-R7 OUT AGND Figure 11. EV-ADF5901SD2Z Schematic (Page 5) Rev. 0 | Page 12 of 18 13381-011 R30 0 VIN 1UF 1 C39 R26 C35 C D1 1N4001 MBR0540T1G 1 VOUT 2 SENSE 3 GND 4 NC PAD PAD ADP7104 8 VIN 7 PG 6 GND 5 EN 0 1UF C R33 1UF A R23 1UF VSUPPLY A IN U6 D2 EV-ADF5901SD2Z Evaluation Board User Guide AHI TP30 1 AGND AGND 10PF DNI TBD0402 C30 DNI VREG TBD0402 C25 C23 0.22UF DNI TBD0402 C20 0.047UF 1 C2 C28 1 TP31 0.22UF TP29 C31 AGND AGND AGND C1 1000PF 0.1UF C29 C27 10PF C26 1000PF VCO_AHI 0.1UF C24 C22 10PF C21 C15 0.1UF C18 1000PF TX_AHI C16 UG-864 AGND R22 5.1K AGND C2 C1 VCO_AHI IO VTUNE IN AUXB OUT AUX OUT RSET MUXOUT OUT PAD 32 31 30 29 28 27 26 25 AGND AGND OUT TX_AHI DOUT LE DATA CLK CE AGND VREG AHI OUT IN IN IN IN IN IN IN 1000PF IO C2 C1 1000PF AGND Figure 12. EV-ADF5901SD2Z Schematic (Page 6) Rev. 0 | Page 13 of 18 13381-012 REFIN R21 IN OUT OUT ATEST AGND LO_OUT AGND AGND AHI 9 10 11 12 13 14 15 AHI 16 OUT 24 23 22 21 20 19 18 17 5901 TBD0603 IO AGND 1 TX_OUT1 2 AGND 3 4 5 AGND 6 TX_OUT2 7 AGND 8 U101 UG-864 EV-ADF5901SD2Z Evaluation Board User Guide TP6 SPI_CLK CLK_PLL R11 OUT IN OUT 330 R51 TP7 OUT SPI_MOSI R47 R52 GPIO0 LE_PLL 0 IN LE_TX R48 OUT 390 R53 330 10K OUT R37 R56 TP11 AGND AGND AVDD_TX TP1 IO OUT 390 R38 330 GPIO2 IN R49 10K TX_DATA R14 R54 GPIO3 IN AGND 330 IN GPIO5 OUT TP8 R13 TP15 DATA_TX 330 390 R34 IN AGND GPIO6 0 TP13 DATA_PLL 330 IN R55 10K SPI_MOSI R12 IN AGND AGND IN GPIO4 CLK_TX R46 390 R28 330 10K SPI_CLK IN TP14 TP10 TP12 CE_TX OUT 330 AGND TP9 IO DVDD_PLL 10K R39 IN DOUT_TX R50 SPI_MISO 0 OUT TP2 GPIO7 IN CE_PLL R15 OUT 390 R44 330 AGND IN MUXOUT_PLLR24 0 13381-013 TP19 GPIO1 OUT Figure 13. EV-ADF5901SD2Z Schematic (Page 7) Rev. 0 | Page 14 of 18 EV-ADF5901SD2Z Evaluation Board User Guide AGND 10PF C11 1000PF 0.1UF C9 10PF C8 9 IO IO DVDD REFIN 21 SW2 20 SW1 C19 24 CP 17 MUXOUT OUT IN IN IN IN IN IN IN RFINA RFINB CE TXDATA CLK DATA LE 5 RFINA 4 RFINB 13 CE 12 TXDATA 14 CLK 15 DATA 16 LE MUXOUT AGND Figure 14. EV-ADF5901SD2Z Schematic (Page 8) Rev. 0 | Page 15 of 18 OUT ADF4159CCPZ 13381-014 AGND CP 1000PF 2 3 1 10 11 PAD R16 TBD0603 IN 1000PF RSET SDVDD DVDD VP 23 U2 CPGND DGND SDGND EPAD C17 R17 5.1K AGND REFIN DNI AGND AVDD 8 7 6 18 19 22 AVDD IO AGND VP 1000PF C7 0.1UF C6 10PF C5 AGND C10 VP DVDD 1000PF C4 0.1UF C3 AVDD UG-864 13381-015 EV-ADF5901SD2Z Evaluation Board User Guide Figure 15. EV-ADF5901SD2Z Layer 1 (Component Side) 13381-016 UG-864 Figure 16. EV-ADF5901SD2Z Layer 4 (Bottom Plane) Rev. 0 | Page 16 of 18 EV-ADF5901SD2Z Evaluation Board User Guide UG-864 ORDERING INFORMATION BILL OF MATERIALS Table 1. Quantity 4 6 6 6 1 1 1 6 1 1 1 1 1 1 1 1 2 2 3 1 1 1 11 13 Part Description 1 nF, 0603 capacitors 1 nF, 0402 capacitors 10 pF, 0402 capacitors 100 nF, 0603 capacitors 47 nF, 0402 capacitor 220 nF, 0402 capacitor 220 nF, 0603 capacitor 1 µF, 0805 capacitors 22 µF, 0805 capacitor 10 pF, 0603 capacitor 220 pF, 0805 capacitor 3.3 nF, 0805 capacitor 100 pF, 0805 capacitor Diode, standard, 1 A, 50 V Diode, Schottky, 0.5 A, 20 V Ferrite bead CONN-PCB end launch jack CONN-PCB high frequency SMA CONN-PCB SMA RA jack CONN-PCB vertical type RCPT SMD CONN-PCB single SKT black CONN-PCB single SKT red 0 Ω, 0402 resistors 0 Ω, 0603 resistors Manufacturer AVX AVX AVX AVX Kemet Taiyo Yuden AVX AVX Murata AVX Multicomp Kemet Multicomp Multicomp ON Semiconductor Wuerth Elektronik Emerson Emerson (Johnson) Rosenberger Hirose Deltron Deltron Multicomp Multicomp Part Number 06035A102JAT2A 04023C102KAT2A 04023A100JAT2A 06033C104JAT2A C0402C473K3RACTU JMK105B7224KV-F 06033C224KAT2A 08053C105KAZ2A GRM21BE70G226ME51L 06035A100JAT2A MCCA001042 C0805C332J5GACTU MCCA001040 1N4001 MBR0520LT1G 7427-92642 142-0701-851 142-0761-801 02K243-40M FX8-120S-SV(21) 571-0100 571-0500 MC 0.0625W 0402 1% 0R MC 0.063W 0603 0R 9 2 1 5 2 Reference Designator C1, C2, C17, C19 C4, C7, C10, C18, C24, C29 C5, C8, C11, C21, C26, C31 C3, C6, C9, C15, C22, C27 C16 C23 C28 C32, C34 to C36, C38, C39 C40 C41 C12 C13 C14 D1 D2 E1 J1, J7 J2, J3 J4, J8, J9 J5 P2 P3 R1, R2, R23, R25 to R27, R29 to R33 R3 to R5, R7 to R10, R24, R40, R45, R50, R55, R56 R11 to R15, R46 to R49 R17, R22 R20 R28, R34, R37, R38, R44 R35, R36 330 Ω, 0603 resistors 5.1 kΩ, 0603 resistors 0 Ω, 0805 resistor 390 Ω, 0603 resistors 100 kΩ ,0603 resistor Multicomp Multicomp Multicomp Multicomp Multicomp 1 1 1 1 1 R41 R43 R18 R19 U2 Multicomp Multicomp Multicomp Multicomp Analog Devices, Inc. 1 2 2 1 1 1 2 1 U3 U4 U5 U6 Y1 U101 TP16, TP17 TP23 10 kΩ, 0603 resistor 91 Ω, 0603 resistor 510 Ω, 0805 resistor 1 kΩ, 0805 resistor ADF4159 13 GHz Fractional-N frequency synthesizer IC 32 Kbit serial EEPROM 3.0 V CMOS linear regulator 1.8 V CMOS linear regulator 3.3 V CMOS linear regulator 100 MHz crystal clock oscillator ADF5901 24 GHz TX MMIC Black test point Red test point MC 0.063W 0603 330R MC 0.063W 0603 5k1 MC 0.1W 0805 0R MC 0.063W 0603 390R MC 0.063W 0603 5% 100K MC 0.063W 0603 10K MC 0.063W 0603 1% 91R MC 0.1W 0805 1% 510R MC 0.1W 0805 1% 1K ADF4159CCPZ Microchip Analog Devices Analog Devices Analog Devices Connor-Winfield Analog Devices Vero Vero 24LC32A-I/MS ADP150AUJZ-3.0 ADP150AUJZ-1.8 ADP7104ARDZ-3.3 CWX113-100.0M ADF5901WCCPZ-U6 20-2137 20-313137 Rev. 0 | Page 17 of 18 UG-864 Quantity 3 1 2 4 5 28 EV-ADF5901SD2Z Evaluation Board User Guide 4 2 Reference Designator C20, C25, C30 C33 C37, C42 R6, R16, R21, R42 R39, R51 to R54 TP1 to TP15, TP18 to TP22, TP24, TP29 to TP32, TP34 to TP36 C1, C2, C17, C19 SCREW1, SCREW2 2 NUT1, NUT2 Part Description Do not install Do not install Do not install Do not install Do not install Do not install Manufacturer Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Part Number Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable 1 nF, 0603 capacitors Screw, cheese, nylon, M3X10, PK100 Nut/washer, nylon, M3, PK100 AVX ALLTHREAD Plastics Limited DURATOOL 06035A102JAT2A 119030010 1140030 RELATED LINKS Resource ADF5901 ADF4159 ADP7104 Description Product Page, 24 GHz VCO and PGA with 2-Channel PA Output Product Page, Direct Modulation/Fast Waveform Generating, 13 GHz, Fractional-N Frequency Synthesizer Product Page, 20 V, 500 mA, Low Noise, CMOS LDO ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG13381-0-12/15(0) Rev. 0 | Page 18 of 18