EV-ADF5904SD2Z User Guide
UG-791
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for the ADF5904 4-Channel, 24 GHz Receiver Downconverter
FEATURES
GENERAL DESCRIPTION
Contains ADF5904 4-channel, 24 GHz receiver downconverter
Accompanying software allows control of ADF5904 functions
from a PC
The EV-ADF5904SD2Z evaluation board allows the user to
evaluate the performance of the ADF5904 24 GHz receiver
downconverter. Figure 1 shows the board, which contains the
ADF5904, five high frequency SMA connectors for the local
oscillator (LO) input, four receiver (Rx) inputs, eight SMA
connectors for the baseband outputs, banana connectors for
power supply, and a connector for serial interface.
EVALUATION KIT CONTENTS
EV-ADF5904SD2Z evaluation board
ADDITIONAL EQUIPMENT
The evaluation kit also contains software that is compatible with
Windows® XP and later versions to allow easy programming of
the device.
PC running Windows XP or more recent version
Analog Devices, Inc., EVAL-SDP-CS1Z system demonstration
platform-serial (SDP-S) board
Spectrum analyzer (optional)
Oscilloscope
5 V power supplies
USB cable
This evaluation board requires an EVAL-SDP-CS1Z SDP-S
board (not supplied with the kit). The SDP-S board allows
software programming of the ADF5904 device.
Full specifications on the ADF5904 are available in the product
data sheet, which should be consulted in conjunction with this
user guide when working with the evaluation board.
DOCUMENTS NEEDED
ADF5904 data sheet
REQUIRED SOFTWARE
Analog Devices ADF5904 Software
12895-001
EVALUATION BOARD PHOTOGRAPH
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 14
UG-791
EV-ADF5904SD2Z User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Power Supplies ...............................................................................4
Evaluation Kit Contents ................................................................... 1
Input Signals...................................................................................4
Additional Equipment ..................................................................... 1
Output Signals ...............................................................................4
Documents Needed .......................................................................... 1
Default Operation .........................................................................4
Required Software ............................................................................ 1
Evaluation Board Software ...............................................................5
General Description ......................................................................... 1
Evaluation and Test ...........................................................................7
Evaluation Board Photograph......................................................... 1
Evaluation Board Schematics and Artwork ...................................8
Revision History ............................................................................... 2
Ordering Information .................................................................... 13
Quick Start Guide ............................................................................. 3
Bill of Materials ........................................................................... 13
Evaluation Board Hardware ............................................................ 4
Related Links ................................................................................... 13
REVISION HISTORY
3/15—Revision 0: Initial Version
Rev. 0 | Page 2 of 14
EV-ADF5904SD2Z User Guide
UG-791
QUICK START GUIDE
Follow these steps to quickly evaluate the ADF5904.
1.
2.
3.
4.
5.
6.
Connect the power supply to the EV-ADF5904SD2Z:
a. 5 V to Banana Connector P2
b. GND to Banana Connector P1
Install the ADF5904 software.
Connect the SDP-S motherboard to the PC and to the
EV-ADF5904SD2Z evaluation board.
Follow the hardware driver installation procedure.
Run the ADF5904 software.
Select the ADF5904 device and the USB board in the
Select Device and Connection tab of the software front
panel window (see Figure 2).
7.
Check that the message SDP board connected appears at
the bottom left of the software window (see Figure 2).
8. Connect an ac-coupled RF source to LOIN SMA and
connect an ac-coupled RF source to one of the RXxIN
input SMAs.
9. In the Main Controls tab, click Initialize.
10. Connect the corresponding Rx baseband channel output to
an oscilloscope.
11. Measure the results.
Rev. 0 | Page 3 of 14
UG-791
EV-ADF5904SD2Z User Guide
EVALUATION BOARD HARDWARE
The evaluation board requires an SDP-S motherboard to
program the device. The SDP-S board is not included and must
be purchased separately. The EV-ADF5904SD2Z schematics are
shown in Figure 5 to Figure 9. The top layer and assembly layout
are shown in Figure 10.
POWER SUPPLIES
The evaluation board is powered via one external supply, 5 V
connected as described in the Quick Start Guide section.
INPUT SIGNALS
The LO input pin and the Rx input pins on the ADF5904
contain a dc bias voltage; the inputs must be ac-coupled to the
evaluation board.
OUTPUT SIGNALS
The baseband outputs from the ADF5904 contain dc bias
voltages and are available on the J3 to J11 output SMAs.
Table 1. Baseband Output Mapping
Rx Input
RF1IN
RF2IN
RF3IN
RF4IN
Baseband Outputs
J3, J4
J6, J7
J8, J9
J10, J11
DEFAULT OPERATION
All components necessary for ADF5904 operation are inserted
on the board.
Rev. 0 | Page 4 of 14
EV-ADF5904SD2Z User Guide
UG-791
EVALUATION BOARD SOFTWARE
The control software for the EV-ADF5904SD2Z is included in
the evaluation kit on a CD. To install the software, follow the
on-screen instructions.
To run the software, click the ADF5904 file on the desktop or
from the Start menu.
Note that, when connecting the board, it takes approximately
5 sec to 10 sec for the status label to change.
12895-002
In the Select Device and Connection tab, select the device and
the connection method, and click Connect.
Confirm that Analog Devices Eval Board connected is
displayed at the bottom left of the window (see Figure 2).
Otherwise, the software has no connection to the evaluation
board.
Figure 2. Software Front Panel Display—Select Device and Connection
Rev. 0 | Page 5 of 14
UG-791
EV-ADF5904SD2Z User Guide
The Main Controls tab controls the ADF5904 device settings
(see Figure 3).
12895-003
This tab allows the user to select general options available for
the ADF5904, including power up/down control and register
readback.
On initial power-up of the device, click the Initialize button
to perform the initialization sequence as described in the
ADF5904 data sheet.
Figure 3. Software Front Panel Display—Main Controls
Rev. 0 | Page 6 of 14
EV-ADF5904SD2Z User Guide
UG-791
EVALUATION AND TEST
To evaluate and test the performance of the ADF5904, take the
following steps:
2.
3.
4.
5.
Install the SDP-S software drivers. Connect the evaluation
board to a PC using the supplied USB cable. Follow the
hardware driver installation procedure that appears.
Connect the SDP-S connector to the EV-ADF5904SD2Z.
Install the ADF5904 software.
Connect an ac-coupled RF signal to LOIN SMA.
Connect an ac-coupled RF signal to the RX1IN input SMA.
Connect a 1 MΩ, ac-coupled oscilloscope to the J3 and J4
output SMAs.
7. Run the ADF5904 software.
8. Select the SDP-S board and the ADF5904 device in the
Select Device and Connection tab of the software window.
9. In the Main Controls tab, click Initialize to power up the
ADF5904 (see Figure 3). See Figure 4 for the suggested
setup.
10. Measure the baseband output signals.
SDP-S
ADAPTOR
BOARD
PC
SIGNAL
SOURCE
OSCILLOSCOPE
DC BLOCK
SIGNAL
SOURCE
+5V
12895-004
1.
6.
POWER
SUPPLY
Figure 4. Typical Evaluation Setup
Rev. 0 | Page 7 of 14
UG-791
EV-ADF5904SD2Z User Guide
EVALUATION BOARD SCHEMATICS AND ARTWORK
J3
RF1IN
RX1_RF
1
RX1_BBO
BLOCK2
2 3
RX1_RFIN
RX1_BBO
RX1_BBOB
RX1_BBO
RX1_BBOB
RX2_BBO
RX2_BBOB
RX2_BBO
RX2_BBOB
RX3_BBO
RX3_BBOB
RX3_BBO
RX3_BBOB
J4
RX2_RFIN
RF2IN
RX2_RF
1
RX3_RFIN
2 3
RX4_RFIN
RX1_BBOB
J6
RX2_BBO
RX4_BBO
RX4_BBOB
LO_RFIN
CE
RX4_RF
J2
RX2_BBOB
ATEST
DATA
CE
DOUT
TP1
DOUT
CLK
LO_AHI
RF4IN
J7
TP4
J8
RX3_BBO
TP3
DATA
RX4_BBO
RX4_BBOB
LE
RX34_AHI
LE
CLK
TP2
2 3
RX12_AHI
RF3IN
RX3_RF
1
J9
0
R3
0
R2
R1
2 3
0
RX3_BBOB
LOIN
LO_IN
1
AVDD
J10
AVDD
INTERFACE
RX4_BBO
CLK
DATA
LE
CE
DOUT
CLK
DATA
LE
CE
DOUT
AVDD
AVDD
J11
RX4_BBOB
AVDD
P1
AGND
POWER
P2
VDD
J1
12895-005
AVDD1
Figure 5. Evaluation Board Schematic (Page 1)
Rev. 0 | Page 8 of 14
EV-ADF5904SD2Z User Guide
UG-791
R19
8.2K
R20
10K
AVDD
IO
0
R16
TP5
TP9
1
1
R4
330
LE
R9
CE
IO
IO
330
TP8
TP6
1
1
R8
CLK
DOUT
DATA
R18
R10
0
330
IO
IO
IO
1
Figure 6. Evaluation Board Schematic (Page 2)
Rev. 0 | Page 9 of 14
12895-006
DGND
10K
390
R17
R15
390
R14
390
TP7
390
330
R12
GPIO0
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
SPI_SEL_A
SPI_SEL_B
SPI_SEL_C
SPI_CLK
SPI_MISO
SPI_MOSI
R11
SDP-S
0
R13
DGND
Rev. 0 | Page 10 of 14
Figure 7. Evaluation Board Schematic (Page 3)
IO SPI_SEL_B
IO SPI_SEL_C
IO GPIO0
IO GPIO2
IO GPIO4
IO GPIO6
DGND
R6
TBD0603
1 J5
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
FX8-120S-SV(21)
R5
100K
R7
100K
J5
1
2
3
6
7
VIO
DGND
U3
8
A0 VCC
EEPROM
A1
A2 SDA 5
SCL
WP
VSS
4
24LC32A-I/MS
IO SPI_SEL_A
IO SPI_MOSI
IO SPI_MISO
IO SPI_CLK
IO GPIO1
IO GPIO3
IO GPIO5
IO GPIO7
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
FX8-120S-SV(21)
12895-007
UG-791
EV-ADF5904SD2Z User Guide
EV-ADF5904SD2Z User Guide
UG-791
IO
6
GND
EN
4.7UH
0
3
GND
PAD
AVDD
IO
2
4
NC
12895-008
AGND
AGND
1UF
C12
PAD
R23
AGND
SENSE
1UF
C10
1N4001
C
D1
A
AGND
5
PG
R25
1
R24
0
L1
VOUT
1UF
7
ADP7104
VIN
C11
8
R22
MBR0540T1G
R21
0
C
0
IO
A
0
U2
D2
VDD
0
R26
AVDD1
AGND
AGND
IN
IN
IN
IN
IN
IN
Figure 8. Evaluation Board Schematic (Page 4)
IN
AGND
IN
RX1_RFIN
RX12_AHI
RX3_BBO
25
RX3_BBOB
LO_AHI
27
26
LO_RFIN
28
29
30
23
3
22
21
4
RX2_RFIN
RX2_BBO
5
20
6
19
7
18
8
17
RX3_RFIN
RX34_AHI
RX4_RFIN
RX4_BBOB
IN
IN
IN
IN
16
RX4_BBO
ATEST
14
DOUT
15
13
12
CE
DATA
11
CLK
9
RX2_BBOB
C9
C4
12895-009
IN
IN
IN
IN
IN
IN
10PF
IN
C2
LO_AHI
100PF
2
10PF
AGND
1000PF
IN
24
IN
100PF
C5
C3
C1
IN
1
ADF5904
RX34_AHI
1000PF
RX1_BBO
10PF
LE
100PF
U1
C8
10
1000PF
C7
31
PAD
C6
32
RX1_BBOB
AGND
RX12_AHI
AGND
Figure 9. Evaluation Board Schematic (Page 5)
Rev. 0 | Page 11 of 14
EV-ADF5904SD2Z User Guide
12895-010
UG-791
Figure 10. Layer 1 (Component Side)
Rev. 0 | Page 12 of 14
EV-ADF5904SD2Z User Guide
UG-791
ORDERING INFORMATION
BILL OF MATERIALS
Table 2.
Qty
3
3
3
1
1
10
1
1
5
1
1
3
4
1
1
1
2
1
9
1
1
2
2
1
4
1
1
1
1
1
1
1
5
Reference Designator
C1, C2, C6
C3, C4, C7
C5, C8, C9
D1
D2
J1 to J4, J6 to J11
J5
L1
LOIN, RF1IN to RF4IN
P1
P2
R4, R8, R10
R11, R12, R14, R15
R17
R19
R20
R5,R7
R6
TP1 to TP9
U2
U3
Screw1, Screw2
Nut1, Nut2
U1
R21, R22, R25, R26
R24
R23
C12
C11
C10
R16
R9
R1, R2, R3, R13, R18
Description
0.1 μF capacitor
1000 pF capacitor
10 pF capacitor
Diode
Diode
Connector, PCB, end launch, SMA
120-way connector, 0.6 mm pitch
4.7 μH inductor
2.92 mm Rosenberger connectors
Black, 4 mm, banana socket
Red, 4 mm, banana socket
330 Ω resistor
390 Ω resistor
10 kΩ resistor
8.2kΩ resistor
10 kΩ resistor
100 kΩ resistor
Do not populate
Connector, PCB, test point, red
Linear regulator, 3.3 V, 20 V, 500 mA, ultralow noise
32k, I2C, serial EEPROM, MSOP8
Screw, cheese, nylon
Nut/washer, nylon
ADF5904 Rx MMIC
0 Ω resistor
0.33 Ω resistor
Do not populate
100 μF capacitor
10 μF capacitor
1 μF capacitor
Do not populate
Do not populate
0 Ω resistor
RELATED LINKS
Resource
ADF5904
ADP7104
Description
Product Page, 4-Channel, 24 GHz, Receiver Downconverter
Product Page, 20 V, 500 mA, Low Noise, CMOS LDO
Rev. 0 | Page 13 of 14
Manufacturer
AVX
Murata
AVX
Multicomp
On Semiconductor
Emerson
Hirose
Coilcraft
Rosenberger
Deltron
Deltron
Vishay
Multicomp
Multicomp
Multicomp
Multicomp
Yageo (Phycomp)
Not applicable
Keystone Electronics Corp
Analog Devices
Microchip
Allthread
Duratool
Analog Devices
Multicomp
Welwyn
Not applicable
Kemet
Murata
Taiyo/Yuden
Not applicable
Not applicable
Multicomp
Part Number
06033C104JAT2A
GRM1555C1H102JA01
04025U100GAT2A
1N4001
MBR0520LT1G
142-0701-851
FX8-120S-SV(21)
EPL2014-472ML
02K243-40M
571-0100
571-0500
CRCW0603330RFKEA
MC 0.063W 0603 390R
MC 0.063W 0603 10K
MC 0.063W 0603 1% 8K2
MC 0.063W 0603 10K
RC0402JR-07100KL
Not applicable
5000
ADP7104ARDZ-3.3
24LC32A-I/MS
119030010
1140030
ADF5904BCPZ
MC 0.0625W 0402 1% 0R
LRCS0402-0R33FT5
Not applicable
T520B107M006ATE040
GRM21BR61A106KE19L
TMK107BJ105KA-T
Not applicable
Not applicable
MC 0.063W 0603 0R
UG-791
EV-ADF5904SD2Z User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly
return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred
damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications
to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer.
Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR
REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE
EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY
RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE
EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG12895-0-3/15(0)
Rev. 0 | Page 14 of 14
工商网监
湘ICP备2023018690号
