Evaluation Board User Guide
EV-ADuCRF101
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
ADuCRF101 Evaluation Board User Guide
FEATURES
EVALUATION BOARD OVERVIEW
4-layer PCB (33 mm × 55 mm form factor)
2 power supply options
2.2 V to 3.6 V from an external power supply
5 V from interface/emulator board
Power indicator/general-purpose LEDs
Reset and download push buttons
8-pin connector to the interface/emulator board or to
RS-232 interface cable (top row)
Access to ADuCRF101 pins on the two footprints for throughhole connectors on the edge of the board
32.768 kHz watch crystal footprint
Matching network and SMA connector for wireless
communication
The ADuCRF101 mini board allows a user to program, debug,
and evaluate the performance of the ADuCRF101. Its small
form factor makes it the ideal hardware for evaluation of large
wireless sensor networks.
EVALUATION KIT CONTENTS
A DVD containing evaluation software, user guides,
data sheets, and example code
Antenna
Emulator board (QuickStart and QuickStart Plus kits only)
GENERAL DESCRIPTION
Six kits are available, from a mini board only, to a combination
of emulator and boards.
•
•
•
•
•
•
EV-ADuCRF101MK3Z mini board for 433 MHz operation
EV-ADuCRF101MK1Z mini board for 868 MHz/915 MHz
operation
EV-ADuCRF101QSP1Z QuickStart Plus for 868 MHz/915
MHz operation
EV-ADuCRF101QSP3Z QuickStart Plus for 433 MHz
operation
EV-ADuCRF101QS1Z QuickStart for 868 MHz/915 MHz
operation
EV-ADuCRF101QS3Z QuickStart for 433 MHz operation
Figure 1 shows the content of a quick start kit, one mini board
with antenna and one emulator.
11040-001
The ADuCRF101 is a fully integrated, data acquisition solution
designed for low power wireless applications. It features a 12-bit
ADC, a low power ARM Cortex™-M3 processor, a 431 MHz
to 464 MHz and 862 MHz to 928 MHz RF transceiver, and
Flash/EE memory, in a 9 mm × 9 mm LFCSP package.
Figure 1 ADuCRF101 Mini Board and Emulator Board
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 12
EV-ADuCRF101
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Power Indicator/General-Purpose LEDs ...................................4
Evaluation Kit Contents ................................................................... 1
Crystal Circuits ..............................................................................4
General Description ......................................................................... 1
Emulator Interface ........................................................................4
Evaluation Board Overview ............................................................ 1
Reset/Download Push Buttons ....................................................4
Revision History ............................................................................... 2
RS-232 Interface ............................................................................4
Development Systems Description ................................................ 3
RF Matching Network ..................................................................5
Mini Kit .......................................................................................... 3
Sensitivity Measurements.............................................................5
QuickStart Kit ............................................................................... 3
Mini Board Connectors ....................................................................6
QuickStart Plus Kit ....................................................................... 3
Edge Connectors J1 and J2...........................................................6
J-Link OB Emulator ..................................................................... 3
Emulation and Serial Interface Connector J3............................6
Mini Board Features ......................................................................... 4
Mini Board Schematic And Artwork..............................................7
Power Supply ................................................................................. 4
Bill of Materials ............................................................................... 11
REVISION HISTORY
5/13—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
Evaluation Board User Guide
EV-ADuCRF101
DEVELOPMENT SYSTEMS DESCRIPTION
J-LINK OB EMULATOR
Different systems are available that are optimized for the
various types of evaluation requirements.
Table 1 lists the contents available for each type of system.
Table 1. Development Systems Content
Content
Mini Board
Antenna
Emulator Board
Battery Holder
DVD
Mini Kit
(MK)
1
1
0
0
1
QuickStart
(QS)
1
1
1
0
1
QuickStart Plus
(QSP)
2
2
1
1
1
The J-Link OB emulator board provides a debug path via serial
wire, supply, and UART communication with the ADuCRF101
mini board. Figure 2 shows a top view of the emulator board.
The J2 connector plugs into the ADuCRF101 mini board. The
J2 connector pinout is shown in Figure 3.
The mini board is optimized for 433 MHz or 868MHz/915MHz
operation.
Table 2 lists the models and their optimized communication
frequency.
Table 2. Development Systems Models
Description
Mini kit
Mini kit
QuickStart
QuickStart
QuickStart Plus
QuickStart Plus
Frequency
868 MHz/915 MHz
433 MHz
868 MHz/915 MHz
433 MHz
868 MHz/915 MHz
433 MHz
11040-002
Model
EV-ADuCRF101MK1Z
EV-ADuCRF101MK3Z
EV-ADuCRF101QS1Z
EV-ADuCRF101QS3Z
EV-ADuCRF101QSP1Z
EV-ADuCRF101QSP3Z
Figure 2. Emulator, Top View
MINI KIT
The mini kit evaluation kits contain one mini board, one
antenna, and a DVD containing software and documentation.
This system can be ordered, in addition to the other development systems, to increase the number of nodes in a wireless
sensor network.
The mini kit does not contain an emulator.
QUICKSTART KIT
11040-003
The QuickStart kit evaluation kits contain one mini board,
one antenna, one emulator board, and a DVD containing
software and documentation.. This kit is ideal to evaluate the
ADuCRF101 as part of an existing wireless system.
QUICKSTART PLUS KIT
The QuickStart Plus evaluation kit contain two mini boards,
two antennas, one emulator board, a battery holder, and a DVD
containing software and documentation. The QuickStart Plus
kit has all the components needed to quickly set up a two-node
wireless communication system.
Figure 3. J2 Connector
For downloading and debugging, LK1, LK2, LK4, and LK6
must be inserted. LK3 and LK5 are required to communicate
via UART.
When measuring current consumption using an external supply
on the ADuCRF101 mini board IOVDD pins, it is recommended
that the emulator be disconnected.
Rev. 0 | Page 3 of 12
EV-ADuCRF101
Evaluation Board User Guide
MINI BOARD FEATURES
POWER SUPPLY
Two options are available for powering the board.
•
•
Use the emulator board.
The 5 V USB supply on J3.7 is regulated via the linear
voltage regulator, U2. The 3.3 V regulator output powers
the red power LED, D2. When LK1 is in place, the regulator
output is connected back to the emulator board on J3.8.
The regulator powers the ADuCRF101 only when LK1 and
LK2 are in place on the mini board.
Apply an external power supply to IOVDD on J1.3.
To measure the ADuCRF101 current consumption only,
apply the supply directly to IOVDD. Remove LK1 and LK2,
and disconnect the emulator board.
It is also possible to power the device from an external
supply at 3.3 V while debugging with the emulator board.
Remove LK1 and insert LK2.
Each device supply pin of the ADuCRF101 is decoupled with
0.1 µF and 100 pF capacitors. A 68 µF capacitor is used on the
supply line for the transceiver.
POWER INDICATOR/GENERAL-PURPOSE LEDS
A power LED (D2) is used to indicate that the interface board
is providing the supply to the board. Note that LK1 and LK2
must be inserted for the ADuCRF101 to be powered from the
emulator board. A general-purpose LED (D1) is connected to
P4.2 of the ADuCRF101. When P4.2 is cleared, the LED is
turned on. When P4.2 is set, the LED is turned off.
Other emulators supporting serial wire debug (for example, JLINK
Version 6 and higher) can be used. The connections between
the mini board and the 20-pin JTAG connector are listed in
Table 3.
Table 3. Mini Board/Emulator Connections
Signal
GND
J3 Connector
(Mini Board)
J3.2
VDD
SWDIO
SWCLK
RESET
J3.8
J3.3
J3.5
J3.1
20-Pin JTAG Connector (Emulator)
Pin 4, Pin 6, Pin 8, Pin 10, Pin 12,
Pin 14, Pin 16, Pin 18, Pin 20
Pin 1 and Pin 2
Pin 7
Pin 9
Pin 15
Note that the internal pull-ups on SWDIO and SWCLK are
sufficient, and no external resistors are required.
RESET/DOWNLOAD PUSH BUTTONS
A reset push button is available to allow the user to reset the part
manually. When pressed, the reset pin of the ADuCRF101 is pulled
to ground. Because the RESET pin on the ADuCRF101 is Schmidttriggered internally, there is no need to use an external Schmidt
trigger on this pin. A second push button, BOOT, is connected to
P0.6/IRQ2 and facilitates serial download mode entry.
RS-232 INTERFACE
To interface the ADuCRF101 UART pins to a PC, the USB UART
interface on the emulator board is the first option to consider.
EMULATOR INTERFACE
The ADuCRF101 P1.0 and P1.1 lines are available on the top
row of the J3 connector and can be directly connected to EVALADUC-CABLE1Z, as shown in Figure 4, or similar adaptor that
includes an RS-232 interface device providing the required level
shifting or a USB UART interface. Supply should be provided
on J1.3 (IOVDD) and LK2 inserted when using an RS-232
interface.
Nonintrusive emulation and download are possible on the
ADuCRF101 via serial wire by connecting the emulator board
to the J3 connector. Only two signals are required for debug
purposes: SWDIO and SWCLK. The reset signal is also connected
and can be used to provide a reset from the PC, if required.
To communicate via UART using a UART cable, EVAL-ADUCCABLE1Z, the supply should be between 3 V and 3.6 V because
the cable is operational only in this supply range. The EVALADUC-CABLE1Z is available for purchase on the Analog
Devices, Inc. web site.
CRYSTAL CIRCUITS
11040-004
Footprints for a through-hole 32.768 kHz watch crystal (Y2)
and its two capacitors are included on the board. This crystal can
be selected by software as the clock source of the wake-up timer.
Figure 4. Mini Board Connected to EVAL-ADUC-CABLE1Z
Rev. 0 | Page 4 of 12
Evaluation Board User Guide
EV-ADuCRF101
RF MATCHING NETWORK
An RF matching network is available to match the LNA input
impedance and PA output with the 50 Ω SMA connector (J4)
for ADuCRF101 at different frequencies depending on the
board used.
Different boards are available based on the RF transceiver
frequency required. See Table 4 for the relevant model numbers.
Table 4. ADuCRF101 Development Systems Optimized
Communication Frequency
Frequency
868 MHz/915 MHz
Topology
Differential PA
433 MHz
Differential and
single-ended PA
Models
EV-ADuCRF101MK1Z
EV-ADuCRF101QS1Z
EV-ADuCRF101QSP1Z
EV-ADuCRF101MK3Z
EV-ADuCRF101QS3Z
EV-ADuCRF101QSP3Z
The list of components for the different models available is
available in Table 8 to Table 12.
The 868 MHz/915 MHz models come with a matching network
for differential PA only. The matching network components can
be modified to evaluate the single-ended PA. The list of components for single-ended PA operating at 868 MHz/915 MHz is
available in Table 13.
The 433 MHz models come preloaded with a combined matching
network for both differential and single ended PA operation.
SENSITIVITY MEASUREMENTS
To perform the BER test on the RF transceiver, the internal
clock and data signals of the transceiver can be brought to the
ADuCRF101 GPIO pins
•
•
Rev. 0 | Page 5 of 12
The CLOCK signal can be brought out to P0.6.
The DATA signal can be brought out to P2.6.
EV-ADuCRF101
Evaluation Board User Guide
MINI BOARD CONNECTORS
EDGE CONNECTORS J1 AND J2
Table 6. Pin Functions for Edge Connector J2
ADuCRF101 signals, such as GPIOs and analog inputs are
available on the edge of the board, on two unpopulated
through-hole connectors. These two connectors can be used
to plug the mini board into a prototype board.
Pin No.
J2-1
J2-2
J2-3
J2-4
J2-5
J2-6
J2-7
J2-8
J2-9
J2-10
J2-11
J2-12
J2-13
J2-14
J2-15
J2-16
J2-17
J2-18
J2-19
The pinout of the two edge connectors is shown in Table 5 and
in Table 6.
Table 5. Pin Functions for Edge Connector J1
Pin Number
J1-1
J1-2
J1-3
J1-4
J1-5
J1-6
J1-7
J1-8
J1-9
J1-10
J1-11
J1-12
J1-13
J1-14
J1-15
J1-16
J1-17
J1-18
J1-19
J1-20
J1-21
J1-22
J1-23
J1-24
Pin Function
5VOUT
VDDOUT
IOVDD
GND
RESET
NC
P1.5
P1.4
P1.3
P1.2
P1.1
P1.0
P4.0
P4.1
P4.2
P4.3
P4.4
P4.5
P4.6
P4.7
P3.2
P3.3
P3.4
P3.5
Pin Function
ADC0
ADC1
ADC2
ADC3
ADC4
ADC5
VREF
LVDD1
GND
P0.7
P0.6
P0.5
P0.4
P0.3
P0.2
P0.1
P0.0
P2.6
P2.4
EMULATION AND SERIAL INTERFACE CONNECTOR J3
Connector J3 provides a connection with the emulation board.
The pinout for the J3 connector is described in Table 7.
Table 7. Pin Functions for Edge Connector J3
Pin No.
J3-1
J3-2
J3-3
J3-4
J3-5
J3-6
J3-7
J3-8
Rev. 0 | Page 6 of 12
Pin Function
RESET
GND
SWDIO
TX
SWCLK
RX
5VUSB
VDDOUT
Evaluation Board User Guide
EV-ADuCRF101
MINI BOARD SCHEMATIC AND ARTWORK
11040-005
Figure 5. ADuCRF101
Rev. 0 | Page 7 of 12
EV-ADuCRF101
Evaluation Board User Guide
11040-006
Figure 6. Connectors
Rev. 0 | Page 8 of 12
Evaluation Board User Guide
EV-ADuCRF101
11040-007
Figure 7. Matching Network Section
Rev. 0 | Page 9 of 12
Evaluation Board User Guide
11040-008
EV-ADuCRF101
11040-009
Figure 8. Top Side Silkscreen
Figure 9. Bottom Side Silkscreen
Rev. 0 | Page 10 of 12
Evaluation Board User Guide
EV-ADuCRF101
BILL OF MATERIALS
Table 8.
Qty
1
1
1
2
1
1
3
1
7
5
2
5
3
1
2
1
6
2
1
1
1
2
1
2
1
6
1
Component
EV-ADuCRF101MKxZ, Rev. E PCB
U1
U2
Boot, Reset
D1
D2
C1, C2, C39
C4
C8, C11, C12, C14, C16, C17, C27
C18, C30, C31, C35, C36
C19, C29
C21, C22, C24, C26, C34
C15,C23, C25
C28
C32, C33
C38
C43, C44, C45, C46, C47, C48
J1, J2
J3
J4
L5
LK1, LK2
R1
R3, R4
R5
R6, R7, R8, R9, R10, R11
Y1
Description
Two-sided surface mount PSB-1
Precision analog microcontroller with RF transceiver
Low quiescent current, 3.3 V linear regulator
SMD push button switch
LED, SMD, green
LED, 0603, red
0.47 µF capacitor, 16 V, Y5V, ceramic 0402
150 nF capacitor, 10%, 10 V, 0402
220 nF ceramic capacitor, 10 V, X5R
100 pF capacitor, 5%, 50 V, 0402
15 pF capacitor, 50 V, 5%, C0G, 0402
0.1 µF ceramic capacitor, 16 V, X7R, 0402
1 µF capacitor, 10%, 6.3 V, X5R, 0402
10 µF ceramic capacitor, 6.3 V, 20%, X5R, 0603
Not inserted
68 µF tantalum capacitor, 6.3 V, 20%, 1210
10 nF ceramic capacitor, 6.3 V, 10%, X7R, 0402
Not inserted
8-pin R/A header
Conn jack end launch PC gold SMA
Ferrite bead, 600 Ω at 100 MHz
2-pin (0.1" pitch) header and shorting shunt
36k Ω resistor, 1/16W, 1%, 0402 SMD
470 Ω resistor, 1/16W, 1% 0402 SMD
1.6 Ω resistor, 1/10W, 5% 0603 SMD
33 Ω resistor, 1/16W, 1% 0402 SMD
Crystal 26 MHz, 10 pF, 3.2 X 2.5 SMD
1
1
Y2
Antenna
32 kHz crystal
433 MHz range antenna
868 MHz/915 MHz range antenna
Order No.
ADuCRF101BCPZ128
ADP121-AUJZ33R7
B3U-1000P
LGQ971
LSQ976-Z
GRM155F51C474ZA01D
GRM155R61A154KE19D
LMK105BJ224KV-F
GRM1555C1H101JD01D
GRM1555C1H150JZ01D
GRM155R71C104KA88D
C0402C105K9PACTU
GRM188R60J106ME47D
Not inserted
TCJB686M006R0070
1758885
Not inserted
9-103324-0
142-0701-851
BLM18BD102SN1D
M20-9990246
RC0402FR-0736KL
MCR01MZPF4700
RC0603JR-071R6L
RHM33CECT-ND
NX3225SA26.000000MHZ-G2
Not inserted
SMAMFDRA433
ANT-916-CW-HWR-SMA
Supplier
Analog Devices
Analog Devices
Analog Devices
Farnell
Digi-Key
Farnell
Digi-Key
Digi-Key
Digi-Key
Farnell
Digi-Key
Digi-Key
Digi-Key
Digi-Key
Not inserted
Digi-Key
Farnell
Not inserted
Farnell
Digi-Key
Digi-Key
Farnell
Digi-Key
Digi-Key
Digi-Key
Digi-Key
Digi-Key
Not inserted
VW Badland
Digi-Key
Table 9. Matching Network Bill of Material for MK1 Model (868 MHz/915 MHz Operation, Differential PA)
Qty
4
2
1
3
2
Component
C3, C7, C13, C42
C9, C10
C20
L2, L6, L8
L3, L4
Description
Not inserted
2.7 pF ceramic capacitor, 50 V, C0G, 0402
100 pF capacitor, 5%, 50 V, 0402
Not inserted
10.4 nH RF inductor, ceramic core, 5% 0603
Order No.
Not inserted
GRM1555C1H2R7CZ01D
GRM1555C1H101JD01D
Not inserted
0604HQ-10NXJL
Supplier
Not inserted
Digi-Key
Farnell
Not inserted
Coilcraft
Table 10. Harmonic Filter Bill of Material for MK1 Model (868 MHz/915 MHz Operation, Differential PA)
Qty
1
2
2
1
2
Component
C5
C6, C37
C40, C41
L1
L7, L9
Description
270 pF ceramic capacitor, 50 V 5% C0G, 0402
3.6 pF ceramic capacitor, 50 V C0G, 0402
Not inserted
15 nH RF inductor, ceramic core, 5% 0603
7.5 nH RF inductor, ceramic core, 5% 0603
Rev. 0 | Page 11 of 12
Order No.
GRM1555C1H271JA01D
GJM1555C1H3R6CB01D
Not inserted
0603HP-15NXJL
0603HP-7N5XJL
Supplier
Digi-Key
Digi-Key
Not inserted
Coilcraft
Coilcraft
EV-ADuCRF101
Evaluation Board User Guide
Table 11. Matching Network Bill of Material for MK3 Model (433 MHz Operation)
Qty
1
2
2
2
1
1
1
2
Component
C3
C9, C10
C13, C20
C7, C42
L2
L8
L6
L3, L4
Description
270 pF capacitor, 5%, 50 V 0402
5.6 pF ceramic capacitor, 50 V, C0G, 0402
100 pF capacitor, 5%, 50 V, 0402
Not inserted
100 nH 0603 inductor
Not inserted
15 nH 0603 inductor
27 nH 0603 inductor
Order No.
GRM1555C1H271JA01D
GRM1555C1H5R6DZ01D
GRM1555C1H101JD01D
Not inserted
0603HP-R10XJL
Not inserted
0603HP-15NXJL
0603HP-27NXJL
Supplier
Digi-Key
Digi-Key
Digi-Key
Not inserted
Coilcraft
Not inserted
Coilcraft
Coilcraft
Order No.
GRM1555C1H271JA01D
GJM1555C1H8R2DB01D
Not inserted
0603HP-30NXJL
0603HP-18NXJL
Supplier
Digi-Key
Digi-Key
Not inserted
Coilcraft
Coilcraft
Table 12. Harmonic Filter Bill of Material for MK3 Model (433 MHz Operation)
Qty
1
2
2
1
2
Component
C5
C6, C37
C40, C41
L1
L7, L9
Description
270 pF ceramic capacitor, 50 V, 5%, C0G 0402
8.2 pF cerami capacitor, 50 V, C0G 0402
Not inserted
30 nH 0603 inductor
18 nH 0603 inductor
Table 13. Matching Network Bill of Material for Single-Ended PA Topology at 868 MHz/915 MHz Operation
Qty
1
2
1
2
1
1
1
1
2
Component
C3
C9, C10
C13
C7, C42
C20
L2
L8
L6
L3, L4
Description
150 pF ceramic capacitor, 50V 5% NP0 0402
1.5 pF ceramic capacitor, 50 V, C0G 0402
100 pF capacitor, 5%, 50 V 0402
Not inserted
100 pF capacitor, 5%, 50 V 0402
47 nH 0603 inductor
Not inserted
1.8 nH 0603 inductor
10 nH 0603 inductor
Order No.
GCM1555C1H151JA16D
GJM1555C1H1R5CB01
GRM1555C1H101JD01D
Not inserted
GRM1555C1H101JD01D
0603HP-47NXJL
Not inserted
0603HP-1N8XJL
0604HQ-10NXJL
Supplier
Digi-Key
Digi-Key
Digi-Key
Not inserted
Digi-Key
Coilcraft
Not inserted
Coilcraft
Coilcraft
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written
notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED,
RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF
INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S
POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES
SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will
comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the
Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and
Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is
expressly disclaimed.
©2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG11040-0-5/13(0)
Rev. 0 | Page 12 of 12
工商网监
湘ICP备2023018690号
