EVAL-24TSSOPEBZ

EVAL-24TSSOPEBZ User Guide UG-1036 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluation Board for 24-Lead TSSOP Devices in the Switches and Multiplexers Portfolio FEATURES GENERAL DESCRIPTION 24-lead TSSOP evaluation board Clamp allows the main device to be easily changed Gold pin connectors allow the addition of passive components SMB connectors for the input/output of signals Additional space on-board to allow for prototyping The EVAL-24TSSOPEBZ evaluation board evaluates 24-lead TSSOP devices in the Switches and Multiplexers Portfolio, purchased separately. A clamp is supplied with the EVAL24TSSOPEBZ to secure a 24-lead TSSOP device to the evaluation board without the need for soldering, making the board reusable for multiple devices. EVALUATION KIT CONTENTS Figure 1 shows the EVAL-24TSSOPEBZ evaluation board. A 24-lead TSSOP device can be clamped or soldered to the center of the evaluation board. Each pin of the device has a corresponding link from K1 to K24 that can be set to either VDD or GND. A wire screw terminal supplies VDD and GND. SMB connectors on the evaluation board allow additional external signals to be supplied to the device. In addition, there is space available at the top of the board for prototyping. EVAL-24TSSOPEBZ evaluation board ONLINE RESOURCES Documents Needed Data sheet of the device being evaluated EVAL-24TSSOPEBZ user guide EQUIPMENT NEEDED Full specifications of the device under test (DUT) are available in the corresponding product data sheet, which should be consulted in conjunction with this user guide when using the evaluation board. Device being evaluated DC voltage source Analog signal source Method to measure voltage, such as a digital multimeter (DMM) 14927-001 EVAL-24TSSOPEBZ EVALUATION BOARD PHOTOGRAPH Figure 1. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 7 UG-1036 EVAL-24TSSOPEBZ User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Power Supply..................................................................................3 Evaluation Kit Contents ................................................................... 1 Link headers ...................................................................................3 Online Resources .............................................................................. 1 SMB Connectors............................................................................3 Equipment Needed ........................................................................... 1 Input Signal Traces ........................................................................3 General Description ......................................................................... 1 Evaluation Board Schematic and Artwork.....................................4 EVAL-24TSSOPEBZ Evaluation Board Photograph ................... 1 Ordering Information .......................................................................7 Revision History ............................................................................... 2 Bill of Materials ..............................................................................7 Evaluation Board Hardware ............................................................ 3 REVISION HISTORY 8/2016—Revision 0: Initial Version Rev. 0 | Page 2 of 7 EVAL-24TSSOPEBZ User Guide UG-1036 EVALUATION BOARD HARDWARE POWER SUPPLY Table 1. Link Header Descriptions Connector J5 supplies the VDD and GND supplies to the board. These supplies can be selected for each pin of the device by setting the link headers to either VDD or GND. When a VSS supply is needed, apply the voltage directly to the VSS pin of the device by removing the corresponding link and applying the voltage directly to the middle pin of the link header. LINK HEADERS The link headers supply the DUT with either VDD or GND. The headers are designated K1 to K24 with the number corresponding to the pin number of the device. Table 1 summarizes the link headers and how they function on the evaluation board. Label K1 to K24 Position H L Description VDD GND SMB CONNECTORS There are four SMB connectors on the evaluation board, J1 to J4. When an SMB cable is connected to one of these connectors, the input signal becomes available on the corresponding P1 to P4 port. Apply this signal to the relevant pin of the device by forming a connection from P1 to P4 to a gold pin connector found on the relevant trace. INPUT SIGNAL TRACES Each trace includes three sets of gold pin connectors, two sets that can place a load on the signal path to ground and another set that is in series with the signal path. The three sets of gold pin connectors can create a simple resistor capacitor (RC) filter. Rev. 0 | Page 3 of 7 UG-1036 EVAL-24TSSOPEBZ User Guide 14927-002 EVALUATION BOARD SCHEMATIC AND ARTWORK Figure 2. EVAL-24TSSOPEBZ Evaluation Board Schematic Rev. 0 | Page 4 of 7 UG-1036 14927-003 EVAL-24TSSOPEBZ User Guide 14927-004 Figure 3. EVAL-24TSSOPEBZ Evaluation Board Silkscreen Figure 4. EVAL-24TSSOPEBZ Evaluation Board Top Layer Rev. 0 | Page 5 of 7 EVAL-24TSSOPEBZ User Guide 14927-005 UG-1036 Figure 5. EVAL-24TSSOPEBZ Evaluation Board Bottom Layer Rev. 0 | Page 6 of 7 EVAL-24TSSOPEBZ User Guide UG-1036 ORDERING INFORMATION BILL OF MATERIALS Table 2. Reference Designator C1 C2 C3 to C74 J1 to J4 J5 K1 to K24 P1 to P4 T1 to T24 Description 0.1 µF, 50 V, X7R, ceramic capacitor 10 µF, 10 V tantalum capacitor Harwin subminiature sockets (2) SMB sockets 2-pin terminal block (5 mm pitch) Jumper blocks using 3-pin SIP header Harwin subminiature sockets (2) Test points Part Number GRM21BR71H104KA01L TAJB106K016RNJ H3153-01 1206013 KRM 02 M20-9990345 and M7566-05 H3153-01 20-313137 Stock Code FEC 2408531 FEC 498-737 FEC 2120079 FEC 310-682 FEC 151-785 FEC 512-047 and 150-411 FEC 2120079 FEC 240-345 ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG14927-0-8/16(0) Rev. 0 | Page 7 of 7