EVAL-AD5292EBZ

EVAL-AD5292DBZ User Guide UG-1439 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluating the AD5292 Digital Potentiometer FEATURES GENERAL DESCRIPTION Full featured evaluation board in conjunction with high voltage digital potentiometer motherboard (EVAL-MB-HV-SDZ) PC control via SDP-B or SDP-S PC software for control 20-time programmable 1% resistance precision This user guide describes the full featured EVAL-AD5292DBZ board for evaluating the AD5292 digital potentiometer. The AD5292 is a single-channel, 1024-position digital potentiometer with less than ±1% end to end resistor tolerance error and 20-time programmable (20-TP) memory. The AD5292 is capable of operating at high voltages, supporting both dual supply ±10.5 V to ±16.5 V and single supply 21 V to 33 V operation. EVALUATION KIT CONTENTS The AD5292 uses a serial interface that operates at clock rates of up to 50 MHz and is compatible with the standard serial peripheral interface (SPI). EVAL-AD5292DBZ board EVAL-MB-HV-SDZ motherboard CD containing Self installing software that allows users to control the EVAL-AD5292DBZ and exercise all functions of the device Electronic version of the AD5292 data sheet Electronic version of the EVAL-AD5292DBZ user guide The EVAL-AD5292DBZ incorporates an internal power supply from the USB and allows an external power supply for the logic voltage levels. The logic voltage levels operate from single 2.7 V to 5.5 V supplies. The EVAL-AD5292DBZ can operate in single supply and dual supply modes, and incorporates an output buffer. Complete specifications for the AD5292 can be found in the AD5292 data sheet available from Analog Devices, Inc., and must be consulted in conjunction with this user guide when using the evaluation board. 17216-001 EVAL-AD5292DBZ WITH EVAL-MB-HV-SDZ MOTHERBOARD PHOTOGRAPH Figure 1. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 17 UG-1439 EVAL-AD5292DBZ User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Installing the Software ..................................................................5 Evaluation Kit Contents ................................................................... 1 Software Operation .......................................................................6 General Description ......................................................................... 1 Evaluation Board Schematics and Artwork ...................................7 EVAL-AD5292DBZ with EVAL-MB-HV-SDZ Motherboard Photograph ........................................................................................ 1 Motherboard ..................................................................................7 Revision History ............................................................................... 2 Ordering Information .................................................................... 15 Evaluation Board Hardware ............................................................ 3 Bill of Materials ........................................................................... 15 Daughter Board .......................................................................... 13 Power Supplies .............................................................................. 3 Evaluation Board Software .............................................................. 5 REVISION HISTORY 1/2020—Revision 0: Initial Version Rev. 0 | Page 2 of 17 EVAL-AD5292DBZ User Guide UG-1439 EVALUATION BOARD HARDWARE externally by the P4 connector and P2 connector, as described in Table 1. POWER SUPPLIES Link Options The EVAL-MB-HV-SDZ motherboard supports use of single and dual power supplies. The EVAL-MB-HV-SDZ motherboard can also be used to evaluate a low voltage digital potentiometer using the P9 connector. Several link and switch options are incorporated in the EVALMB-HV-SDZ motherboard and must be set up before using the EVAL-MB-HV-SDZ. The functions of these link options and the default options are described in detail in Table 2. The EVAL-AD5292DBZ evaluation board can be powered either from the system demonstration platform (SDP) port or Table 1. Maximum and Minimum Voltages of the Connectors Connector No. P4-1 Label VDD P4-2 P4-3 P2-1 P2-2 GND VSS VL GND Voltage Analog positive power supply, VDD. Single supply from 21 V to 33 V. Dual supply from 10.5 V to 16.5 V. Dual supply through the ADP5071, 5 V. Analog ground. Analog negative power supply, VSS. Single supply operation of 0 V. Dual supply from −10.5 V to −16.5 V. Digital supply, from 2.7 V to 5.5 V. Digital ground. Table 2. Link Functions Link No. P11 Label/Link Function VIN Default Position B P1 VL B JP3 VDD Not inserted P23 VSS Not inserted P8 VDD_HV A JP4 VSS_HV A P17 A_LV Not inserted JP2 B_LV Not inserted P12 A_HV B Options Selects the power supply, VIN, for the ADP5071 A: V_SINGLE (derived from VDD_EXT, external supply from the P4 connector) B: +5 V (5 V from SDP-B or SDP-S) Selects the logic power supply, VLOGIC A: VL_EXT (external supply from the P2 connector) B: VL3V3 (3.3 V from SDP-B or SDP-S) Selects the low voltage positive power supply, VDD_LV A: +5 V (5 V from SDP-B or SDP-S) B: VDD_EXT (external supply from the P4 connector) C: VL3V3 (3.3 V from SDP-B or SDP-S) Selects the low voltage negative power supply, VSS_LV A: VSS_EXT (external supply from the P4 connector) B: AGND Selects the high voltage positive power supply, VDD_HV A: 15 V (+15 V from ADP5071) B: VDD_EXT (external supply from the P4 connector) Selects the high voltage negative power supply, VSS_HV A: −15 V (−15 V from ADP5071) B: VSS_EXT (external supply from the P4 connector) C: AGND Selects the voltage at Terminal A for the low voltage digital potentiometer A: A_EXT (external supply from the P3 connector) B: VDD Selects the voltage at Terminal B for the low voltage digital potentiometer A: VSS B: AGND C: B_EXT (external supply from the P3 connector) Selects the voltage at Terminal A for the high voltage digital potentiometer A: A_EXT (external supply from the P3 connector) B: VDD_HV Rev. 0 | Page 3 of 17 UG-1439 EVAL-AD5292DBZ User Guide Link No. JP1 Label/Link Function B_HV Default Position A P24 P21 Supply for ADP5071 A_HV channel links A1_HV A2_HV A3_HV A4_HV A_LV channel links A1_LV A2_LV A3_LV A4_LV B_LV channel links B1_LV B2_LV B3_LV B4_LV B_HV channel links B1_HV B2_HV B3_HV B4_hV Buffer connector W1_BUF W2_BUF W3_BUF W4_BUF Inserted Options Selects the voltage at Terminal B for the high voltage digital potentiometer A: VSS_HV B: AGND C: B_EXT (external supply from the P3 connector) Connects VIN to the supply terminal of ADP5071 Inserted Inserted Inserted Inserted Connects Terminal A1 to A_HV Connects Terminal A2 to A_HV Connects Terminal A3 to A_HV Connects Terminal A4 to A_HV Not inserted Not inserted Not inserted Not inserted Connects Terminal A1 to A_LV Connects Terminal A2 to A_LV Connects Terminal A3 to A_LV Connects Terminal A4 to A_LV Not inserted Not inserted Not inserted Not inserted Connects Terminal B1 to B_LV Connects Terminal B2 to B_LV Connects Terminal B3 to B_LV Connects Terminal B4 to B_LV Inserted Inserted Inserted Inserted Connects Terminal B1 to B_HV Connects Terminal B2 to B_HV Connects Terminal B3 to B_HV Connects Terminal B4 to B_HV Inserted Inserted Inserted Inserted Connects Terminal W1 to an output buffer Connects Terminal W2 to an output buffer Connects Terminal W3 to an output buffer Connects Terminal W4 to an output buffer P18 P19 P25 P20 Rev. 0 | Page 4 of 17 EVAL-AD5292DBZ User Guide UG-1439 EVALUATION BOARD SOFTWARE INSTALLING THE SOFTWARE The EVAL-AD5292DBZ kit includes a CD containing the evaluation board software. The software is compatible with Windows® 7, Windows 8 and Windows 10. Install the software before connecting the SDP board to the USB port of the PC so that the SDP-B or SDP-S board is recognized when it is connected to the PC. 1. 2. 3. 4. 5. Start the Windows operating system and insert the CD into the CD-ROM drive. The installation software opens automatically. If it does not open automatically, run the setup.exe file from the CD. After the installation is complete, power up the evaluation board as described in the Power Supplies section. Connect the EVAL-AD5292DBZ and EVAL-MB-HV-SDZ to the SDP-B or SDP-S board, and then connect the SDP-B or SDP-S board to the PC using the USB cable included with the SDP-B or SDP-S board. When the software detects the evaluation board, follow the instructions that appear to complete installation. 17216-002 To install the software, perform the following steps: Figure 2. Connectivity Error Window To run the program, perform the following steps: 1. 2. Select Start > All Programs > Analog Devices > AD5292 > AD5292 Eval Board. To uninstall the program, select Start > Control Panel > Add or Remove Programs > AD5292 Eval Board. If the SDP-B or SDP-S board is not connected to the USB port when the software is launched, a connectivity error displays (see Figure 2). Connect the EVAL-AD5292DBZ board to the USB port of the PC, wait a few seconds, click Rescan, and follow the instructions. 17216-003 The main window of the EVAL-AD5292DBZ software then opens, as shown in Figure 3. Figure 3. EVAL-AD5292DBZ Software Main Window Rev. 0 | Page 5 of 17 UG-1439 EVAL-AD5292DBZ User Guide SOFTWARE OPERATION In the main window of the software, there are four buttons. POWERDOWN (or POWERUP when the device is off) powers the device down and up. When the button is clicked, the software shutdown bit toggles automatically. SOFT RESET sends a reset by software. HARD RESET sends a reset by hardware. EXIT closes the program, but does not reset the device. The main window is also divided in three sections. Clicking BLOW FUSE saves the current value stored in the RDAC register into the 20-TP memory. Enable the 20-TP program in the CONTROL REGISTER section. 20-TP Clicking READ returns the value stored in the location specified in the LOCATION box. READ also computes the location of the last fuse programmed. CONTROL REGISTER Clicking 20-TP ON/OFF enables the C0 bit (20-TP program enable). Enable this bit to write into the 20-TP memory. RDAC Clicking WRITE changes the contents of the RDAC register and displays the value of the resistor, as shown in the Figure 4. Clicking RDAC ON/OFF enables the C1 bit (RDAC register write protect). Enable this bit to allow updates of the wiper position through the digital interface. 17216-004 R-PERFORMANCE ON/OFF is the C2 bit (calibration enable). Figure 4. Resistor Value, Left Position Is Resistance from A to W, Right Position Is Resistance from W to B Rev. 0 | Page 6 of 17 EVAL-AD5292DBZ User Guide UG-1439 EVALUATION BOARD SCHEMATICS AND ARTWORK MOTHERBOARD EEPROM SDP CONNECTOR VLOGIC CONNECTOR GPIO CONNECTOR EEPROM_A0 P15 P10 100K R30 TBD0603 R15 R16 CTB5000/2 TSW-106-08-G-S A AND B PIN CONNECTORS POWER SUPPLY CONNECTORS A_EXT P3 VDD_EXT R6 0 R11 0 R12 0 R8 0 R13 0 R9 0 R14 0 AD1 GPIO3 GPIO1 SCL SDA CTB5000/3 CTB5000/3 B_EXT VSS_EXT I2C PMOD CONNECTOR SPI PMOD CONNECTOR SCLK SDO SDI SYNC P4 1 2 3 1 2 3 R7 0 R10 0 U100 8 VCC 1 A0 2 A1 3 A2 6 5 SCL SDA SDA 7 WC_N GND 4 24LC64-I/SN 1 2 3 4 5 6 P14 SYNCB SDI SDO SCLK P16 1 2 3 4 5 6 VL_EXT 1 2 3 4 5 6 7 8 SCL SDA VL_EXT TSW-106-08-G-S VL VL 68021-108HLF DGND BLK AGND BLK W1 W1 BLK W3 W3 BLK W2 W2 BLK W4 W4 BLK R26 SYNCB BLK 2.2K R22 TEST POINTS SDO BLK SDO SYNCB R37 0 GPIO1 GPIO1 BLK GPIO2 GPIO2 BLK SCLK BLK GPIO4 GPIO4 BLK SDI BLK VOUT1 VOUT1 BLK GPIO3 GPIO3 BLK GPIO0 GPIO0 BLK VL R33 SDA BLK SCLK SDI FX8-120S-SV(21) Figure 5. SDP Connector and Power Supply Rev. 0 | Page 7 of 17 VOUT3 VOUT3 BLK AD0 VOUT2 SCL BLK SCL SDA VIO_+3.3V TBD0603 VL AD0 BLK VOUT2 BLK AD1 VOUT4 AD1 BLK VOUT4 BLK 17216-007 5VUSB SCL P2 1 2 VIO_+3.3V 2.2K R2 0 R3 0 R4 0 VIO_+3.3V GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 TBD0603 AD0 GPIO2 GPIO0 R1 0 VL_EXT R24 GPIO4 RESET_IN_N BMODE1 UART_RX UART_TX GND GND RESET_OUT_N SLEEP_N EEPROM_A0 WAKE_N NC NC NC NC NC NC GND GND NC NC NC CLKOUT TMR_C TMR_D TMR_A TMR_B GPIO6 GPIO7 GND GND GPIO4 GPIO5 GPIO2 GPIO3 GPIO0 GPIO1 SCL_1 SCL_0 SDA_1 SDA_0 GND GND SPI_SEL1/SPI_SS_N SPI_CLK SPI_SEL_C_N SPI_MISO SPI_SEL_B_N SPI_MOSI GND SPI_SEL_A_N SERIAL_INT GND SPI_D3 SPORT_TSCLK SPI_D2 SPORT_DT0 SPORT_DT1 SPORT_TFS SPORT_DR1 SPORT_RFS SPORT_TDV1 SPORT_DR0 SPORT_TDV0 SPORT_RSCLK GND GND PAR_FS1 PAR_CLK PAR_FS3 PAR_FS2 PAR_A1 PAR_A0 PAR_A3 PAR_A2 GND GND PAR_CS_N PAR_INT PAR_RD_N PAR_WR_N PAR_D1 PAR_D0 PAR_D3 PAR_D2 PAR_D5 PAR_D4 GND GND PAR_D7 PAR_D6 PAR_D9 PAR_D8 PAR_D11 PAR_D10 PAR_D13 PAR_D12 PAR_D14 GND GND PAR_D15 PAR_D17 PAR_D16 PAR_D19 PAR_D18 PAR_D21 PAR_D20 PAR_D23 PAR_D22 GND GND USB_VBUS VIO(+3.3V) GND GND GND GND NC NC VIN NC 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 100K EEPROM_A0 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 UG-1439 EVAL-AD5292DBZ User Guide +5V 5VUSB P8 RED VL3V3 C15 1 2 3 VDD_HV M20-9990346 VDD_EXT RED M20-9990346 JP3 2 1 A 4 3 B 6 5 C 2213S-06G DS1 C17 5.1K 69157-102HLF P24 +5V VDD_EXT VL3V3 1 2 3 VDD VDD 1 RED 1 2 VSS_EXT P23 3V3 1 VL3V3 2.2UF VDD_HV RED 1 7 VIN VOUT 2 8 VOUT VIN 5 EN 3 SENSE/ADJ 6 SS GND PAD 4 PAD R44 0 C18 +15V VSS_HV JP4 2 1 A VSS_HV 4 3 B 6 5 RED C 2213S-06G U4 +5V V_SINGLE 1000PF C3 10BQ030PBF 10UF VDD_EXT JUMPER SETTINGS FOR THE SUPPLY VSS 4.7UF ADP7118ARDZ-3.3 V_SE RED D1 VSS C4 R17 M20-9990346 +5V 2.2UF RED 1 0.1UF C2 1 2 3 VIN VSS_EXT 600OHMS V_SINGLE P11 VIN -15V 1.6 10UF C1 SELECTION BETWEEN 5VUSB AND VSINGLE SUPPLY +5V RED R5 TLMS1000GS08 E1 R46 0 VIN VSS P12 1 2 3 2 3 `1-2' TBD 1 JP7 M20-9990346 VDD_HV 3 VDD L2 R20 0 R47 1UF R27 118K 2.32MEG B0540W-7-F -15V RED -15V L3 TBD0603 R40 R45 0 Figure 6. EVAL-MB-HV-SDZ Schematic—Power Supply 2.43MEG 7.32K TBD0603 M20-9990346 Rev. 0 | Page 8 of 17 TBD0603 C16 1UF R23 D3 1 2 3 RED C13 L1 `1-2' TBD 14K C11 47PF P17 A_LV 1 A_LV 1200PF C9 0.0056UF 2 A_EXT JP2 B_LV 2 1 A 4 3 B_LV 1 B RED 6 5 C 2213S-06G 3.3UH C7 C12 RED A_HV A_HV A_HV RED JP6 5.6UH B_EXT A_EXT B_HV 13 AGND 19 PGND PAD PAD B_EXT 22PF 11 18 R39 C10 17216-008 `1-2' TBD 1 2 JUMPER SETTINGS FOR THE A AND B TERMINAL R28 C8 C14 TBD0603 3 EN +15V RED 1 20 5 6 10 12 137K JP5 8 SS INBK 7 EN1 14 SW1 VREG FB1 ADP5071ACPZ COMP1 9 EN2 COMP2 2 VREF SYNC/FREQ 4 FB2 SLEW 3 SW2 SEQ R29 1 U3 2.2UF M20-9990346 1UF C5 VL3V3 EN TBD0603 16 PVINSYS 17 PVIN2 15 PVIN1 RSS 1 2 3 VL L4 +15V P1 RED B0540W-7-F D2 TBD0603 VL_EXT VL JP1 2 1 A 4 3 B_HV B 6 5 C 2213S-06G VSS_HV 10UF C6 TBD0603 16.5K R19 TBD0603 R34 SELECTION BETWEEN VLOGIC EXTERNAL AND 3.3V FROM THE SDP 41.2K R18 R41 EN EVAL-AD5292DBZ User Guide UG-1439 GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 VL3V3 EEPROM_A0 BUFFER AMPLIFIER DAUGHTER BOARD CONNECTOR 76341-307LF 76342-306LF ADA4610-4ARZ A1_HV A2_HV A3_HV A4_HV 1 3 5 7 2 4 6 8 2 4 6 8 67996-408HLF OUTC OUTD VOUT1 7 VOUT2 8 VOUT3 14 VOUT4 V11 A_HV VOUT CONNECTOR P13 67996-408HLF VOUT1 VOUT2 VOUT3 VOUT4 P25 P25 P18 P18 1 3 5 7 OUTB 1 VSS_HV 76342-306LF 67996-408HLF A1_LV A2_LV A3_LV A4_LV OUTA P21 P21 VSS VDD VSS_HV VDD_HV VL 1 2 3 4 5 6 7 P7 76341-308LF 1 2 3 4 5 6 7 8 9 10 11 12 U2 4 V+ W1_BUF 3 +INA VOUT1 2 -INA W2_BUF 5 +INB VOUT2 6 -INB W3_BUF 10 +INC VOUT3 9 -INC W4_BUF 12 +IND VOUT4 13 -IND A1_HV A3_HV W1 W3 B1_HV B3_HV A2_HV A4_HV W2 W4 B2_HV B4_HV 0.1UF 1 2 3 4 5 6 7 8 P22 A1_LV A3_LV W1 W3 B1_LV B3_LV A2_LV A4_LV W2 W4 B2_LV B4_LV 1UF C22 P5 AD0 AD1 SDA SCL SYNC SDO SDI SCLK P9 A3 1 A1 2 W3 3 W1 4 B3 5 B1 6 A4 7 A2 8 W4 9 W2 10 B4 11 B2 12 76341-307LF C20 P6 1 2 3 4 5 6 7 C19 1UF C21 0.1UF VDD_HV A_LV B1_HV B2_HV B3_HV B4_HV 67996-408HLF 2 4 6 8 1 3 5 7 1 2 3 4 CTB5000/4 B_HV 67996-408HLF 67996-408HLF A1_LV 1 A1_LV B1_LV 1 BLK B1_LV BLK A1_HV 1 A1_HV B1_HV 1 BLK B1_HV BLK A2_LV 1 A2_LV B2_LV 1 BLK B2_LV BLK A2_HV 1 A2_HV BLK B2_HV BLK A3_HV1 A3_HV BLK B3_HV1 B3_HV BLK A4_HV 1 BLK A4_HV B4_HV1 B4_HV BLK P19 P19 2 4 6 8 1 3 5 7 B_LV 67996-408HLF 67996-408HLF P20 P20 W1 W2 W3 W4 67996-408HLF B2_HV1 1 3 5 7 2 4 6 8 W1_BUF W2_BUF W3_BUF W4_BUF A3_LV 1 A3_LV BLK B3_LV 1 B3_LV BLK A4_LV 1 A4_LV BLK B4_LV 1 B4_LV BLK 67996-408HLF Figure 7. EVAL-MB-HV-SDZ Schematic—Daughterboard Connectors Rev. 0 | Page 9 of 17 17216-009 B1_LV B2_LV B3_LV B4_LV EVAL-AD5292DBZ User Guide 17216-010 UG-1439 17216-011 Figure 8. Silkscreen Primary Figure 9. Component Placement Drawing of Motherboard Rev. 0 | Page 10 of 17 UG-1439 17216-012 EVAL-AD5292DBZ User Guide 17216-013 Figure 10. Ground Planes Figure 11. Power Ground Planes Rev. 0 | Page 11 of 17 EVAL-AD5292DBZ User Guide 17216-014 UG-1439 Figure 12. Bottom Layer Side PCB Drawing of Motherboard Rev. 0 | Page 12 of 17 EVAL-AD5292DBZ User Guide UG-1439 DAUGHTER BOARD VL3V3 R3 100K EEPROM_A0 6 SCL 7 A1 A2 SDA 5 SDA SCL WP VSS 4 GPIO0 VDD_HV 24LC64-I/SN U1 6 P2 VL SDO SCLK RDY 13 SDO R4 VLOGIC 2.2K B TP1 14 1 DIN BLK 2 SDA SCL SYNC SDO EXT_CAP SDI RESET SCLK DAUGHTER BOARD CONNECTOR 5 6 W1 3 6 B_HV 5 7 10 9 12 11 77313-101-12LF 7 77313-101-12LF 8 M20-9990846 AD5292BRUZ-50 MTSW-107-07-T-S-240 VDD_HV VL 17216-017 VSS_HV Figure 13. EVAL-AD5290DBZ Schematic 17216-018 9 4 1 P3 2 A_HV 8 4 0.1UF GND 3 P4 2 0.1UF VSS C3 VL 0.1UF C6 10K 1UF R5 C1 GPIO0 1 MTSW-107-07-T-S-240 1 1UF SDI 10 7 P4 P1 W C5 VL 8 SCLK 11 SYNC 12 A 1UF B_HV 5 C2 4 C4 W1 VDD VSS_HV A_HV 3 VDD_HV R2 TBD0603 3 VL3V3 2 U2 8 VCC A0 EEPROM_A0 1 VSS_HV R1 100K VL3V3 Figure 14. Silkscreen Rev. 0 | Page 13 of 17 EVAL-AD5292DBZ User Guide 17216-019 UG-1439 17216-020 Figure 15. Layer 1, Primary Figure 16. Layer 2, Secondary Rev. 0 | Page 14 of 17 EVAL-AD5292DBZ User Guide UG-1439 ORDERING INFORMATION BILL OF MATERIALS Table 3. Motherboard Qty 15 2 1 2 1 1 2 1 2 2 3 1 1 1 1 1 1 2 1 1 4 3 1 1 2 6 1 1 Reference Designator +5V, +15V, −15V, 3V3, A_HV, A_LV, B_HV, B_LV, VDD, VDD_HV, VIN, VL, VSS, VSS_HV, V_SE A1_HV, A1_LV, A2_HV, A2_LV, A3_HV, A3_LV, A4_HV, A4_LV, AD0, AD1, AGND, B1_HV, B1_LV, B2_HV, B2_LV, B3_HV, B3_LV, B4_HV, B4_LV, DGND, GPIO0, GPIO1, GPIO2, GPIO3, GPIO4, SCL, SCLK, SDA, SDI, SDO, SYNCB, VOUT1, VOUT2, VOUT3, VOUT4, W1, W2, W3, W4 C1, C6 C10 C5, C11 C12 C13 C14, C16 C15 C17, C18 C19, C20 C2, C21, C22 C3 C4 C7 C8 C9 D1 D2, D3 DS1 E1 JP1, JP2, JP3, JP4 JP5, JP6, JP7 L1 L2 L3, L4 P1, P8, P11, P12, P17, P23 P10 P13 2 1 5 1 P14, P15 P16 P18, P19, P20, P21, P25 P2 2 1 2 P9, P22 P24 P3, P4 1 2 18 P5 P6, P7 R1, R2, R3, R4, R6, R7, R8, R9, R10, R11, R12, R13, R14, R20, R37, R44, R45, R46 R15, R24, R33, R34, R40, R41, RSS R16, R30 R17 39 7 2 1 Description Red test point Part Number 20-313137 Black test point 20-2137 10 μF capacitor 1200 pF capacitor 1 μF capacitor 2.2 μF capacitor 1 μF capacitor Not populated 1000 pF capacitor 2.2 μF capacitor 1 μF capacitor 0.1 μF capacitor 10 μF capacitor 4.7 μF capacitor 47 pF capacitor 22 pF capacitor 0.0056 μF capacitor Schottky diode Schottky diode Red LED Ferrite bead, 600 Ω 3 row, 2-pin header Not populated 3.3 μH inductor 5.6 μH inductor Not populated 3-pin header 120-pin connector Four contacts, wire to board connector 6-pin header 2-row, 2-pin right angle header 4-row, 2-pin header Two contacts, wire to board connector 6-row, 2-pin female header 2-pin header Three contacts, wire to board connector 8-pin female header 7-pin female header 0 Ω resistors GRM31CR71A106K C1608C0G1H122J JMK107B7105MA GRM188R6YA225KA12D GRM188R61E105KA12D Not populated GRM188R71H102KA01D GRM188R60J225KE19D GRM216R61E105KA12D GRM188R71H104KA93D GRM32ER61H106KA12L GRM188R60J475KE19 06035A470JAT2A CC0603JRNP09BN220 06035C562JAT2A 10BQ030PBF B0540W-7-F TLMS1000-GS08 BLM31PG601SN1L 2213S-06G Not populated LQH32PN3R3NN0L ME3220-562MLB Not populated M20-9990346 FX8-120S-SV(21) CTB5000/4 Not populated 100 kΩ resistors 5.1 kΩ resistors Not populated MC 0.063W 0603 1% 100K CRCW04025K10FKED Rev. 0 | Page 15 of 17 TSW-106-08-G-S 68021-108HLF 67996-408HLF CTB5000/2 76342-306LF 69157-102HLF CTB5000/3 76341-308LF 76341-307LF MC0603WG00000T5E-TC UG-1439 Qty 1 1 2 1 1 1 1 1 1 1 1 Reference Designator R18 R19 R22, R26 R23 R27 R28 R29 R39 R47 R5 U100 1 U2 1 1 U3 U4 EVAL-AD5292DBZ User Guide Description 41.2 kΩ resistors 16.5 kΩ resistors 2.2 kΩ resistors 118 kΩ resistors 2.32 MΩ resistors 2.43 MΩ resistors 137 kΩ resistors 14 kΩ resistors 7.32 kΩ resistors 1.6 Ω resistors I2C serial electronically erasable programmable read only memory (EEPROM) Low noise, precision, rail-to-rail output, junction field effect transistor (JFET) dual op amp DC-to-dc switching regulator Low noise, complementary metal-oxide semiconductor (CMOS) low dropout (LDO) linear regulator Part Number CRCW060341K2FKEA ERA-3AEB1652V MC 0.063W 0603 1% 2K2 ERJ-3EKF1183V CRCW06032M32FKEA CRCW06032M43FKEA MC0063W06031137K ERJ-6ENF1402V ERJ-6ENF7321V SG73S1JTTD1R60F 24LC64-I-SN ADA4610-4ARZ ADP5071ACPZ-R7 ADP7118ARDZ-3.3 Table 4. Daughter Board Qty 1 2 2 1 1 2 1 2 1 1 1 1 1 1 Reference Designator C1 C2, C4 C3, C5 C6 P1 P2, P3 P4 R1, R3 R2 R4 R5 TP1 U1 U2 Description 1 μF capacitor 1 μF capacitor 0.1 μF capacitor 0.1 μF capacitor 8-pin jumpers 7-pin jumpers Six-row, 2-pin header 100 kΩ resistor Not populated 2.2 kΩ resistor 10 kΩ resistor Black test point Compact, +30 V or ±15 V, 256-position digital potentiometer I2C serial EEPROM Rev. 0 | Page 16 of 17 Part Number GRM188R71A105KA61D GRM216R61E105KA12D GRM188R71H104KA93D C0603C104K4RAC 76341-308LF 76341-307LF 76342-306LF ERJ-3EKF1003V Not populated ERJ-3EKF2201V ERJ-3EKF1002V 20-2137 AD5292BRUZ-50 24LC64-I/SN EVAL-AD5292DBZ User Guide UG-1439 NOTES I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors). ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2020 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG17216-0-1/20(0) Rev. 0 | Page 17 of 17