EVAL-AD7416/7/8EBZ

EVAL-AD7416/7/8EBZ User Guide UG-622 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluating the AD7416/AD7417/AD7418 10-Bit ADCs with On-Chip Temperature Sensor FEATURES GENERAL DESCRIPTION Supports the AD7416, AD7417, and AD7418 10-bit temperature sensors AD7417 includes 10-bit, 4-channel ADC AD7418 includes 10-bit, single-channel ADC PC software for control of temperature sensors Supported operating systems Windows XP or Windows 95 (32-bit versions only) This user guide describes the EVAL-AD7416/7/8EBZ evaluation board hardware and software and includes detailed schematics and printed circuit board (PCB) layout artwork. This board is a compact, easy to use platform for evaluating all the features of the AD7416, AD7417, and AD7418 temperature sensors. The EVAL-AD7416/7/8EBZ evaluation board allows the AD7416, AD7417, and AD7418 10-bit analog-to-digital converters (ADCs) with temperature sensor to be quickly and easily evaluated using a PC. Using the evaluation board and its accompanying evaluation software, the AD7416/AD7417/AD7418 can be interfaced to any PC running Windows® 95 or Windows XP. The evaluation software is not currently compatible with 64-bit operating systems. EVALUATION KIT CONTENTS EVAL-AD7416/7/8EBZ evaluation board (fully fitted PCB with USB interface) Evaluation board CD for the AD7416/AD7417/AD7418 containing evaluation software, AD7416/AD7417/AD7418 data sheet, and EVAL-AD7416/7/8EBZ user guide USB A to mini-B cable The evaluation board allows all the input and output functions of the AD7416/AD7417/AD7418 to be exercised without the need for external components. The evaluation software allows control and monitoring of the internal registers of the AD7416/AD7417/ AD7418. The software can also be used without the evaluation board to control and monitor AD7416/AD7417/AD7418 devices connected to an SMBus in the PC. ONLINE RESOURCES Documents Needed AD7416/AD7417/AD7418 data sheet EVAL-AD7416/7/8EBZ user guide Required Software AD7416/AD7417/AD7418 evaluation software Full specifications for the AD7416/AD7417/AD7418 are available in the AD7416/AD7417/AD7418 data sheet, which should be consulted in conjunction with this user guide when using this evaluation board. TYPICAL EVALUATION SETUP SIGNAL GENERATOR 11873-001 PC RUNNING EVALUATION SOFTWARE Figure 1. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 13 UG-622 EVAL-AD7416/7/8EBZ User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Power Supplies ...............................................................................5 Evaluation Kit Contents ................................................................... 1 Input Signals...................................................................................5 Online Resources .............................................................................. 1 How to Use the Software ..................................................................6 General Description ......................................................................... 1 Starting the Software .....................................................................6 Typical Evaluation Setup ................................................................. 1 Read/Write .....................................................................................6 Revision History ............................................................................... 2 Visual Display ................................................................................7 Getting Started .................................................................................. 3 Evaluation Board Schematics and Artwork ...................................8 Software Installation Procedures ................................................ 3 Ordering Information .................................................................... 12 Evaluation Board Setup Procedures........................................... 4 Bill of Materials ........................................................................... 12 Evaluation Board Hardware ............................................................ 5 Related Links ................................................................................... 12 REVISION HISTORY 12/14—Revision 0: Initial Version Rev. 0 | Page 2 of 13 EVAL-AD7416/7/8EBZ User Guide UG-622 GETTING STARTED SOFTWARE INSTALLATION PROCEDURES 5. The EVAL-AD7416/7/8EBZ evaluation kit includes a CD containing software to be installed on your PC before using the evaluation board. The evaluation software is compatible with Windows 95 and Windows XP. The evaluation software must be installed before connecting the evaluation board to the USB port of the PC to ensure that Windows recognizes it and that the driver is installed correctly. To install the software, run the AD741x Evaluation Software Install.exe file from the CD. When the license agreement is accepted, you will be prompted to begin the installation. Click Install. Installing the Evaluation Software 1. 2. Figure 4. Evaluation Software Installation: Begin the Installation 6. A dialog box informs you when the installation is complete. A restart is required after installation; select whether you want to restart your PC at this time or at a later time. Click Finish. Figure 2. Evaluation Software Installation: Welcome Figure 5. Evaluation Software Installation: Installation Is Complete A license agreement appears. Read the agreement, select I accept the terms of the license Agreement, and click Next. 11873-003 4. 11873-005 11873-002 3. With the evaluation board disconnected from the USB port of the PC, insert the installation CD into the CD drive. Double-click the AD741x Evaluation Software Install.exe file to begin the evaluation board software installation. The software is installed to the following default location: C:\Program Files\Analog Devices\Launch AD741x Evaluation Software. A dialog box appears asking to start the installation process. Click Next. 11873-004 To install the AD7416/AD7417/AD7418 evaluation software Figure 3. Evaluation Software Installation: Accepting the License Agreement Rev. 0 | Page 3 of 13 UG-622 EVAL-AD7416/7/8EBZ User Guide d. EVALUATION BOARD SETUP PROCEDURES After following the instructions in the Software Installation Procedures section, plug the evaluation board into your PC through the USB cable. Under Universal Serial Bus Controllers, Cypress EZUSB Sample Device should appear, indicating that the EVAL-AD7416/7/8EBZ driver software is installed and that the board is connected to the PC correctly. Warning The evaluation software and drivers must be installed before connecting the evaluation board to the USB port of the PC to ensure that the evaluation system is correctly recognized when it is connected to the PC. 1. 2. Allow the Found New Hardware Wizard to run after the EVAL-AD7416/7/8EBZ board is plugged into your PC. Check that the evaluation board is connected to the PC correctly using the Device Manager of the PC. Access the Device Manager as follows: a. Right-click My Computer and then click Manage. b. A dialog box may appear asking for permission to allow the program to make changes to your computer. Click Yes. c. The Computer Management box appears. From the list of System Tools, click Device Manager (see Figure 6). 11873-006 Verifying the Board Connection Figure 6. Device Manager: Checking that the Evaluation Board Is Connected to the PC Correctly Rev. 0 | Page 4 of 13 EVAL-AD7416/7/8EBZ User Guide UG-622 EVALUATION BOARD HARDWARE The EVAL-AD7416/7/8EBZ evaluation board contains the following main components, which can be identified from the block diagram, PCB silkscreen, and schematic diagram of overleaf. • • • • • AD7416, AD7417, and AD7418 ICs Power LED OTI LED CONVST input connector, SK1 Input connectors, SK2 and SK3 INPUT SIGNALS To evaluate the AD7417, which has a 4-channel ADC integrated, use SK2 and SK3 to input the corresponding analog signals. If using the AD7418, because its ADC is single channel, SK2 is used as the analog input. SK2 connects to the single analog input of the AD7418, and to VIN1 and VIN2 of the AD7417. SK3 connects to VIN3 and VIN4 of the AD7417. SK1 allows user control of the conversion (see the AD7416/AD7417/AD7418 data sheet for more details on CONVST input). POWER SUPPLIES The EVAL-AD7416/7/8EBZ is directly supplied through the USB cable connected to J1, and does not require any external power supply. Rev. 0 | Page 5 of 13 UG-622 EVAL-AD7416/7/8EBZ User Guide HOW TO USE THE SOFTWARE The Registers area allows a register in the device to be selected for display. The available registers vary with the selected device. The AD7416 has only temperature value and overtemperature limit registers. The AD7417 and AD7418 also have an ADC Value register, where the result of the conversion is stored. In addition, the TOTI setpoint register (Address 0x03) can be written to set the overtemperature limit by clicking OTI Setpoint. STARTING THE SOFTWARE After completing the steps in the Software Installation Procedures section and Evaluation Board Setup Procedures section, launch the AD7416/AD7417/AD7418 evaluation software as follows: 1. 2. From the Start menu, click Programs > Analog Devices > Launch AD741x Evaluation Software. The main window of the software then displays, as shown in Figure 7. If the EVAL-AD7416/7/8EBZ evaluation system is not connected to the USB port when the software is launched, a connectivity error displays. Connect the evaluation system to the USB port of the PC, wait a few seconds, and launch the software again. 11873-009 When the software starts running, it searches for hardware connected to the PC. A dialog box indicates when the evaluation board attached to the PC is detected, and then the main window appears (see Figure 7). Figure 9. Read/Write Tab for AD7417 or AD7418, ADC Value Register Enabled to Read the ADC Conversion Result 11873-007 The Read/Write area displays the data in the currently selected register in binary format, while the Register Information area display the name of the register, its address, and its data contents in hexadecimal and decimal. The device can be set to continuous conversion and reading by clicking the continuous reading button in the Read/Write area so that it shows Continuous Reading is On. When this button shows Continuous Reading is Off, the registers are only updated when a new register is selected. When the overtemperature limit register is selected, change the register value by clicking on the individual bits to toggle them; alternatively, type a hexadecimal or decimal value in the Write area and click the corresponding button. When a new value is entered, the button changes from green to red, and changes back to green when the button is clicked to write the new value to the overtemperature limit register. Note that the overtemperature limit register is only 8 bits, whereas the value registers are 10 bits. For limit comparison, only the 8 MSBs of the temperature value register are compared with the overtemperature limit register; the 2 MSBs are ignored. If the temperature exceeds the set limit, the OTI output of the device goes high. Figure 7. Evaluation Software Main Window READ/WRITE 11873-008 The Read/Write tab displays information about the internal registers of the AD7416/AD7417/AD7418, divided into several areas. The Device area allows the device type to be selected. Figure 8. Read/Write Tab The device can also be put into power-down mode by selecting Power Down in the Power Management area. The device can then be made to power up and perform a single conversion by clicking Single Read button. If the selected device is the AD7417 or AD7418, the analog inputs can be set up by clicking the Ain Control button within the Registers area, which calls up a window to enable the analog inputs, select the internal or external reference voltage, and tie the CONVST input to VDD for continuous conversion, or under external control. Ain Control is also available from the Visual Display tab. Rev. 0 | Page 6 of 13 EVAL-AD7416/7/8EBZ User Guide UG-622 (Because they are linked on the board, the VIN1 channel is the same as VIN2, and VIN3 is the same as VIN4.) Zoom in or out on the horizontal and vertical axes of the graphic display by moving the arrows on the axes up and down or left and right. 11873-010 Overtemperature Limit Figure 10. AD7417/AD7418 ADC Control VISUAL DISPLAY The Visual Display tab allows all the channels of the selected device to be displayed in graphical format. For the AD7416, only temperature is displayed. Set the overtemperature limit and hysteresis using the slider control. The temperature limit and hysteresis are shown on the slider bars, while the actual temperature is shown below the slider. If the temperature exceeds the limit, the OTI alert turns red. The alert turns green again when the temperature falls to the hysteresis value. If OTI is disabled, the alert is invisible. Data Log 11873-011 Output data from the device can be logged into an Excel spreadsheet file. To enable this option, enter the update interval in seconds in the Delay (Sec) field, and then click Make New Log. Figure 11. AD7416 Visual Display 11873-013 For the AD7418, temperature and one analog channel is displayed, while for the AD7417, temperature and four analog channels are displayed. Click the Easy Setup button to set the temperature limit to 70°C and the hysteresis to 50°C, and start the graphic display. Figure 13. Opening a Data Log File Select a folder in which to save the data, enter a new file name or select an existing file name into which to save the data, and then click Open. If an existing log file is selected, the new data does not overwrite the existing data, but is tagged onto the end. When the data log file is opened, the evaluation software begins to write data to it, and the Not Logging to File button changes to Logging to File. To end logging, click Logging to File, and the button changes to Not Logging to File. 11873-012 When the file is opened in Excel, it contains up to six columns of data:    Figure 12. AD7417/AD7418 Visual Display Rev. 0 | Page 7 of 13 Time at which each set of data was logged One column of temperature data Zero, one, or four columns of analog data UG-622 EVAL-AD7416/7/8EBZ User Guide EVALUATION BOARD SCHEMATICS AND ARTWORK 11873-014 Figure 14. EVAL-AD7416/7/8EBZ Schematic—AD7416/AD7417/AD7418 Circuit Rev. 0 | Page 8 of 13 EVAL-AD7416/7/8EBZ User Guide UG-622 11873-015 Figure 15. EVAL-AD7416/7/8EBZ Schematic—USB Controller Circuit Rev. 0 | Page 9 of 13 EVAL-AD7416/7/8EBZ User Guide 11873-016 UG-622 Figure 16. EVAL-AD7416/7/8EBZ Schematic—Analog Inputs Circuit Rev. 0 | Page 10 of 13 UG-622 11873-017 EVAL-AD7416/7/8EBZ User Guide 11873-018 Figure 17. EVAL-AD7416/7/8EBZ Board—Component Side (Layer 1) 11873-019 Figure 18. EVAL-AD7416/7/8EBZ Board—Solder Side (Layer 2) Figure 19. EVAL-AD7416/7/8EBZ Board—Silkscreen Rev. 0 | Page 11 of 13 UG-622 EVAL-AD7416/7/8EBZ User Guide ORDERING INFORMATION BILL OF MATERIALS Table 1. Qty 7 2 1 1 18 5 1 1 1 3 1 1 1 7 2 2 2 3 1 1 1 1 1 1 1 1 1 Reference Designator 3V3_T2, 3V3_T3, AVIN_1/2, AVIN_3/4, OTI, SCL, SDA C1, C2 C3 C4 C5 to C10, C12 to C16, C18, C20, C21, C24 to C26, C28 C11, C19, C22, C23, C27 C17 D1 D2 GND1 to GND3 J1 Q2 R1 R2, R9 to R11, R13 to R15 R3, R6 R4, R5 R7, R20 R8 SK1 to SK3 U1 U2 U3 U4 U5 U6 U7 U8 Y1 Part Description Terminal, PCB, red Value Manufacturer Vero Stock Code FEC 8731144 Capacitor, 0603, 22 pF, 50 V Capacitor, Case D, 47 µF, 10 V Capacitor, Case A, 2.2 µF, 10 V Capacitor, 0603, 100 nF, 25 V 22 pF 47 µF 2.2 µF 0.1 µF Phycomp EPCOS AVX AVX FEC 722005 FEC 9753842 FEC 498646 FEC 317287 Capacitor, Case A, 10 µF, 10 V Capacitor, 0603, 1 µF, 10 V LED, green, SMD LED, red, SMD Terminal, PCB, black Socket, USB mini-AB, SMT Transistor, PNP, SOT-23 Resistor, 0603, 0 Ω Resistor, 0603, 10 kΩ Resistor, 0603, 100 kΩ Resistor, 0603, 2.2 kΩ Resistor, 0603, 1 kΩ Resistor, 0603, 20 kΩ Jack, SMB, PCB, 50R AD7416 temperature sensor AD7418 temperature sensor IC, SM EEPROM serial 64k Precision low dropout voltage regulator AD7417 temperature sensor IC, MCU USB peripheral high speed 56QFN ADG715 CMOS, octal SPST switches AD780 2.5 V/3.0 V voltage reference Crystal, SMD, 24.000000 MHz 10 µF 1 µF AVX Phycomp Kingbright Fairchild Semiconductor Vero Molex Philips Multicomp Multicomp Multicomp Multicomp Multicomp Multicomp Tyco/Greenpar Analog Devices Analog Devices Microchip Analog Devices Analog Devices Cypress Semiconductor Analog Devices Analog Devices AEL FEC 197130 FEC 3188840 FEC 1318243 FEC 1021302 FEC 8731128 FEC 9786490 FEC 1081222 FEC 9331662 FEC 9330399 FEC 9330402 FEC 9330810 FEC 9330380 FEC 9330771 FEC1206013 AD7416ARZ AD7418ARZ FEC 9758070 ADP3303ARZ-3.3 AD7417BRZ Digikey 428-1669-ND ADG715BRUZ AD780ARZ FEC 9509658 0Ω 10 kΩ 100 kΩ 2.2 kΩ 1 kΩ 20 kΩ 24 MHz RELATED LINKS Resource AD7416 AD7417 AD7418 Description Product page, ±1°C 10-bit temperature sensor Product page, ±1°C 10-bit temperature sensor and 4-channel ADC Product page, ±1°C 10-bit temperature sensor and single-channel ADC Rev. 0 | Page 12 of 13 EVAL-AD7416/7/8EBZ User Guide UG-622 NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG11873-0-12/14(0) Rev. 0 | Page 13 of 13