EVAL-ADG5412FEBZ User Guide
UG-731
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for the ADG5412F, Overvoltage Protected Quad SPST
FEATURES
GENERAL DESCRIPTION
Supply voltages
Dual supply: ±5 V to ±22 V
Single supply: 8 V to 44 V
Protected against overvoltage on source pins
Signal voltages up to −55 V and +55 V
LED for visual overvoltage indication
Parallel interface compatible with 3 V logic
On-board LDO regulator for digital supply and control,
if required
The EVAL-ADG5412FEBZ is the evaluation board for the
ADG5412F, which features four independently controlled
single-pole/single-throw (SPST) switches. The ADG5412F has
overvoltage detection and protection circuitry on the source
pins and is protected against signals up to −55 V and +55 V in
both the powered and unpowered states.
EVALUATION KIT CONTENTS
EVAL-ADG5412FEBZ evaluation board
DOCUMENTS NEEDED
ADG5412F data sheet
EVAL-ADG5412FEBZ user guide
EQUIPMENT NEEDED
DC voltage source
±22 V for dual supply
44 V for single supply
Optional digital voltage source: 3 V to 5 V
Analog signal source
Method to measure voltage, such as a DMM
Figure 1 shows the EVAL-ADG5412FEBZ in a typical evaluation
setup. The ADG5412F is soldered to the center of the evaluation
board, and four wire screw terminals are provided to connect to
each of the source and drain pins. Three screw terminals are used
to power the device, with a fourth terminal used to provide a
user defined digital voltage, if required. Alternatively, a low
dropout (LDO) regulator is provided for 5 V digital voltage
control and to supply the LED, which is mounted to provide
visual indication of the fault status of the switch.
Full specifications on the ADG5412F are available in the product
data sheet, which should be consulted in conjunction with this
user guide when using the evaluation board.
12482-001
TYPICAL EVALUATION SETUP
Figure 1. EVAL-ADG5412FEBZ (on Right), Power Supply, and Signal Generator
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. A | Page 1 of 8
UG-731
EVAL-ADG5412FEBZ User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Power Supply..................................................................................4
Evaluation Kit Contents ................................................................... 1
Input Signals...................................................................................4
Documents Needed .......................................................................... 1
Output Signals ...............................................................................4
Equipment Needed ........................................................................... 1
Jumper Settings ..................................................................................5
General Description ......................................................................... 1
Link Headers ..................................................................................5
Typical Evaluation Setup ................................................................. 1
SMB Connectors............................................................................5
Revision History ............................................................................... 2
Evaluation Board Schematics and Artwork ...................................6
Getting Started .................................................................................. 3
Ordering Information .......................................................................8
Evaluation Board Setup Procedure ............................................ 3
Bill of Materials ..............................................................................8
Evaluation Board Hardware ............................................................ 4
REVISION HISTORY
8/15—Rev. 0 to Rev. A
Added Evaluation Board Schematics and Artwork Section and
Figure 3 to Figure 9........................................................................... 6
Added Ordering Information Section, Bill of Materials Section,
and Table 2 ......................................................................................... 8
10/14—Revision 0: Initial Version
Rev. A | Page 2 of 8
EVAL-ADG5412FEBZ User Guide
UG-731
GETTING STARTED
EVALUATION BOARD SETUP PROCEDURE
A simple functionality test can be set up as follows:
The EVAL-ADG5412FEBZ evaluation board is designed to be
operated independently and does not require any additional
evaluation boards or software to operate. An on-board LDO
regulator is provided as the digital power supply for the LED
and to manually control the ADG5412F.
1.
Connect a power supply to J3. Connect VSS and GND
together if a single supply is required.
Insert the header for LK6 to use the on-board LDO
regulator, and place the header for LK5 to Position B.
LK1 through LK4 control the digital signals for each switch
on the ADG5412F.
a. In Position A, the switch is open and presents as an
open circuit.
b. In Position B, the switch is closed and presents with a
resistance of approximately 10 Ω.
The LED lights up to indicate that the switch is operating
normally.
2.
3.
Supply the evaluation board with a dual power source of up to
±22 V or a single supply of up to 44 V by connecting VSS and
GND together. If VDD is greater than 28 V, remove the header
on Link LK6 to protect the on-board LDO regulator, and change
the header on LK5 to Position A to use an alternative digital
voltage supply connected to DC_V1.
4.
J3
VDD
GND
VSS
LK6
VSS
VDD
ADG5412F
ADP1720
J1:S1
J2:D1
D1
S1
IN1
B
LK1
LK5
GND
A
B
J2:D4
J1:S4
S4
A
D4
J3
DC_V1
LK4
IN4
B
A
FF
LK8
LK7
12482-002
LED1
Figure 2. EVAL-ADG5412FEBZ Block Diagram
Rev. A | Page 3 of 8
UG-731
EVAL-ADG5412FEBZ User Guide
EVALUATION BOARD HARDWARE
The operation of the ADG5412F is evaluated using the EVALADG5412FEBZ. Figure 1 shows a typical evaluation setup
where only a power supply and signal generator are required.
Figure 2 shows the block diagram of the main components of
the evaluation board.
INPUT SIGNALS
Using this evaluation board, the ADG5412F is used to pass signals
from either the source or drain connectors. The source pins have
fault detection circuitry that react to an overvoltage event. During
an overvoltage event, the switch is turned off, and the FF pin is
pulled low. See the ADG5412F data sheet for more details.
POWER SUPPLY
Connector J3 provides access to the supply pins of the
ADG5412F. VDD, GND, and VSS link to the appropriate pins
on the ADG5412F. For dual supply voltages, the evaluation
board can be powered from ±5 V to ±22 V. For single supply
voltages, the GND and VSS terminals must be connected together,
and the evaluation board can be powered from 8 V to 44 V.
Additionally, an on-board LDO regulator is provided for digital
control voltage. A secondary voltage source can be connected to
DC_V1 and used as the digital control voltages. To use DC_V1,
place the header of LK5 into Position A. Do not expose the onboard LDO regulator to voltages greater than 28 V; remove LK6
and supply an alternative digital voltage via DC_V1, if required.
Two 4-pin screw connectors are provided to connect to both
the source and drain pins of the ADG5412F. Additional SMB
connector pads are available if extra connections are required. The
ADG5412F is overvoltage protected on the source side, and each
source terminal (S1 to S4) can be presented with a voltage of up to
+55 V or −55 V. See the ADG5412F data sheet for more details.
Each trace on the source and drain side includes two sets of
gold pin connectors, which can be used to place a load on the
signal path to ground. A 0 Ω resistor is placed in the signal path
and can be replaced with a user defined value. The resistor
combined with the gold pin connectors can be used to create a
simple resistor-capacitor (RC) filter.
The ADG5412F uses a parallel interface to control the operation of
the switches. The switch operation can be manually controlled
using the headers on LK1 to LK4, or an external controller can be
interfaced directly to the control pins by using the SMB connectors
(IN1 to IN4) and removing the link headers on LK1 to LK4.
OUTPUT SIGNALS
The only output from the ADG5412F is the FF pin. This pin
indicates the operating state of the device. On the evaluation
board, the FF pin controls the operation of the LED. When the
device is operating normally, the FF pin remains high, and the LED
turns on. If an overvoltage is presented to any of the source pins,
the FF pin is pulled low, and the LED turns off. An SMB connector
is provided to interface the evaluation board with an external
controller, and two gold pin connectors are provided to connect
a pull-up resistor between the FF signal and the digital supply.
Rev. A | Page 4 of 8
EVAL-ADG5412FEBZ User Guide
UG-731
JUMPER SETTINGS
LINK HEADERS
Table 1. Link Header Descriptions
The link headers are used to control the ADG5412F manually,
to configure the digital control voltage, and to isolate the LED
from the rest of the system. Table 1 shows a summary of the
link headers and how they are used on the evaluation board.
Link
Header
LK1
LK1 to LK4 are used to control the switches of the ADG5412F.
Position A opens each switch, and Position B closes the switch.
LK2
LK6 connects the on-board LDO regulator to the VDD supply.
Remove this header to protect the LDO regulator from voltages
higher than 28 V. Change the header on LK5 to Position A to
use an alternative digital voltage connected to DC_V1.
LK8 connects the LED to the digital power supply, and LK7
connects the FF pin of the ADG5412F to the LED control.
LK3
LK4
LK5
LK6
SMB CONNECTORS
The parallel interface of the ADG5412F is controlled manually
using the link headers of LK1 to LK4, or it can be accessed using
the SMB connectors, IN1 to IN4. To use the SMB connectors,
remove the link headers of LK1 to LK4. The FF SMB connector
is used to access the FF digital output from the ADG5412F.
LK7
LK8
Rev. A | Page 5 of 8
Position
A
B
A
B
A
B
A
B
A
B
Inserted
Removed
Inserted
Removed
Inserted
Removed
Description
S1/D1 switch open
S1/D1 switch closed
S2/D2 switch open
S2/D2 switch closed
S3/D3 switch open
S3/D3 switch closed
S4/D4 switch open
S4/D4 switch closed
On-board LDO regulator digital voltage
DC_V1 digital voltage
LDO regulator powered up
LDO regulator unpowered
FF pin connected to LED
FF pin disconnected from LED
LED connected to digital supply
LED isolated
UG-731
EVAL-ADG5412FEBZ User Guide
EVALUATION BOARD SCHEMATICS AND ARTWORK
VSS
T1
R1
C16
0.1µF
J1-1
S1
R11
C1
4
3
R12
C2
S2
14
T3
11
R3
J1-3
R13
C3
S3
6
T5
D1
S2
D2
S3
D3
D4
16
VL
9
8
D3
R17
C7
T8
J2-4
R8
D4
R18
C8
IN1
IN2
0V FLAG
IN3
IN4
FF
B
VL
12
ON = NO FAULT
OFF = FAULT
LED1
LK8
GND
LK4
B A
LK3
B A
LK2
B A
LK1
A
J2-3
R7
7
R14
1
R16
T7
10
ADG5412FBRUZ
C4
D2
C6
15
J1-4
S4
J2-2
R6
2
U1
T4
R4
R15
T6
S1
S4
D1
C5
13
VDD
VSS
J2-1
R5
C15
0.1µF
T2
R2
J1-2
VDD
1
2
R9
D
R10
5
LK7
Q1
BSS138N
G
S
T9
IN1
FF
IN2
12482-003
IN3
IN4
Figure 3. ADG5412F Evaluation Board Schematic—Page 1
VDD
U2
J3-1
C12
0.1µF
±10%
LK6
C13
0.1µF
2
VDD
AGND
J3-2
C9
1µF
4
8
C14
0.1µF
7
VSS
VSS
J3-3
DC_V1
EXT_VL
J3-4
IN
OUT
EN
GND
GND
GND
GND
GND
3
1
5
+5V
C10
1µF
6
+5V
DC_V1
A
B
GND1 GND2
LK5
C11
0.1µF
±10%
ADP1720ARMZ-5
VL
Figure 4. ADG5412F Evaluation Board Schematic—Page 1
Rev. A | Page 6 of 8
12482-004
VDD
UG-731
12482-008
12482-005
EVAL-ADG5412FEBZ User Guide
Figure 8. EVAL-ADG5412FEBZ Layer 3
12482-006
12482-009
Figure 5. EVAL-ADG5412FEBZ Silkscreen
Figure 9. EVAL-ADG5412FEBZ Bottom Layer
12482-007
Figure 6. EVAL-ADG5412FEBZ Top Layer
Figure 7. EVAL-ADG5412FEBZ Layer 2
Rev. A | Page 7 of 8
UG-731
EVAL-ADG5412FEBZ User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 2.
Reference Designator
C1 to C8
C9
C10
C11, C12
C13 to C16
D1 to D4
FF
GND1, GND2
Description
Socket pin, PCB, PK100 (two pins only)
Capacitor, MLCC, X5R, 1 μF, 50 V, 0603
Capacitor, MLCC, X5R, 1 μF, 6.3vV, 0603
50 V tantalum capacitor, D size
50 V, X7R, multilayer ceramic capacitor, 0603 size
50 Ω, SMB socket
50 Ω, SMB socket
Black test point
Manufacturer Part No.
66-3472
GRM188R61H105KAALD
GRM188R60J105KA01D
TAJD106K050RNJ
GRM188R71H104KA93D
SMB1251B1-3GT30G-50
SMB1251B1-3GT30G-50
20-2137
IN1 to IN4
J1 to J3
LED1
LK1 to LK5
LK6 to LK8
Q1
R1 to R8
R9
R10 to R18
S1 to S4
T1 to T9
U1
U2
50 Ω, SMB socket
4-pin terminal block (5 mm pitch)
LED, SMD, green, 0805
3-pin, SIL header and shorting link
2-pin (0.1" pitch) header and shorting shunt
Transistor, N-channel MOSFET, 60 V, 0.23 A, SOT-23
Resistor, 0603 1% 0R
Resistor, 1 kΩ, 0.063 W, 1%, 0603
Socket pin, PCB, PK100 (two pins only)
50 Ω, SMB socket
Red test point
Quad, SPST switch
50 mA, high voltage, micropower linear regulator, 5 V
SMB1251B1-3GT30G-50
CTB5000/4
KP-2012SGC
M20-9990345 & M7567-05
M20-9990246
BSS138N
MC0063W06030R
MC0063W060311K
66-3472
SMB1251B1-3GT30G-50
20-313137
ADG5412FBRUZ
ADP1720ARMZ-5-R7
Stock Code
FEC 329563
FEC 1845736
FEC 9527699
FEC 143-2387
FEC 882-0023
Do not insert
FEC 1111349
FEC 873-1128 (pack of 100;
1 pack per 50 boards)
FEC 1111349
FEC 151791
FEC 1318243
FEC 1022248 & 150410
FEC 1022247 & 150-411
FEC 115-6434
FEC 9331662
FEC 9330380
FEC 329563
Do not insert
FEC 873-1144 (pack of 100 )
ADG5412FBRUZ
ADP1720ARMZ-5-R7
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2014–2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG12482-0-8/15(A)
Rev. A | Page 8 of 8
工商网监
湘ICP备2023018690号
