EVAL-ADG919EBZ

EVAL-ADG901EBZ/EVAL-ADG902EBZ/ EVAL-ADG918EBZ/EVAL-ADG919EBZ User Guide UG-676 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluation Board for the ADG901/ADG902 and ADG918/ADG919 Wideband Absorptive/Reflective Switches FEATURES GENERAL DESCRIPTION Evaluation board for the ADG901/ADG902 SPST and the ADG918/ADG919 SPDT switches RF through for board calibration This user guide describes the evaluation board for the ADG901/ADG902 and ADG918/ADG919 switches. The ADG901/ADG902 (SPST) and the ADG918/ADG919 (SPDT) are wideband switches using a CMOS process to provide high isolation and low insertion loss to 1 GHz. Full data on the ADG901/ADG902 and the ADG918/ADG919 is available in their respective data sheets available from Analog Devices and should be consulted in conjunction with this user guide when using the evaluation board. TYPICAL SETUP J6 J7 VDD IN C4 RF1 J2 C3 R1 C1 C2 RFC RF2 J1 J3 EVAL-ADG901/02/18/19EB WIDE—BAND (>GHz) CAL CMOS SWITCH CAL J5 12159-001 J4 Figure 1. ADG901/ADG902/ADG918/ADG919 Evaluation Board PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. B | Page 1 of 4 UG-676 EVAL-ADG901EBZ/EVAL-ADG902EBZ/EVAL-ADG918EBZ/EVAL-ADG919EBZ User Guide OPERATING THE ADG901/ADG902 AND THE ADG918/ADG919 EVALUATION BOARD This evaluation board allows designers to evaluate the highperformance SPST and SPDT wideband switches with a minimum of effort. To prove that these devices meet the user’s requirements, use a power supply and a network analyzer. A 10 μF surface-mount tantalum decoupling capacitor is provided on the VDD line and two 10 pF ceramic capacitors are placed close to the DUT on both the VDD pin and the CTRL pin. Unpopulated component positions are available for the user to apply extra components to meet their design application. J6 This evaluation board has two analog power supply inputs: VDD and CTRL. VDD can equal 1.65 V to 2.75 V. C4 RF1 J2 RF2 C3 R1 C1 C2 RFC RF2 RF1 Table 1. Truth Table ADG901/ADG902 J1 Signal Path RF1 isolated from RF2 RF1 to RF2 GND J3 EVAL-ADG901/02/18/19EB WIDE—BAND (>GHz) CAL CMOS SWITCH Table 2. Truth Table ADG918/ADG919 Signal Path RF2 to RFC RF1 to RFC CAL J5 J4 12159-002 CAL Figure 2. ADG901/ADG902 Top View ADG901/ADG902 VDD CTRL The RF1 port, see Figure 2, is connected through a 50 Ω transmission line to the top left SMA connector, J1. RF2 is connected through 50 Ω transmission lines to the top SMA connector, J2. The port labeled RF2 is ground; connect to ground when evaluating ADG901/ADG902. A through transmission line connects J4 and J5 and this transmission line is used to estimate the loss of the PCB over the environmental conditions being evaluated. J6 J7 VDD IN RF1 C4 J2 RF1 C3 RFC R1 C1 C2 RF2 RFC ADG918/ADG919 The RFC port, see Figure 3, is connected through a 50 Ω transmission line to the top left SMA connector, J1. RF1 and RF2 are connected through 50 Ω transmission lines to the top two SMA connectors, J2 and J3, respectively. A through transmission line connects J4 and J5 and this transmission line is used to estimate the loss of the PCB over the environmental conditions being evaluated. The board is constructed of a four layer, FR4 material with a dielectric constant of approximately 4.3. The total board thickness is 0.062”. Two ground layers with grounded planes provide ground for the RF transmission lines. The transmission lines were designed using a coplanar waveguide with the ground plane model using a trace width of 0.052”, clearance to the ground plane of 0.030”, dielectric thickness of 0.029” and a metal thickness of 0.0014”. Rev. B | Page 2 of 4 J1 RF2 J3 EVAL-ADG901/02/18/19EB WIDE—BAND (>GHz) CAL CMOS SWITCH J4 CAL J5 CAL 12159-003 CTRL 0 1 J7 VDD IN The CTRL inputs are both CMOS and LVTTL compatible. For operation of the ADG901/ADG902 evaluation board, see Table 1 for setup conditions. For operation of the ADG918/ ADG919 evaluation board, see Table 2 for setup conditions. CTRL 0 1 VDD CTRL POWER SUPPLIES Figure 3. ADG918/ADG919 Top View EVAL-ADG901EBZ/EVAL-ADG902EBZ/EVAL-ADG918EBZ/EVAL-ADG919EBZ User Guide 12159-005 EVALUATION BOARD SCHEMATICS AND ARTWORK Figure 4. ADG918/ADG919 Schematic J6 J7 VDD IN C4 RF1 J2 C3 R1 C1 C2 RFC RF2 J1 J3 EVAL-ADG901/02/18/19EB WIDE—BAND (>GHz) CAL CMOS SWITCH CAL J5 12159-004 J4 Figure 5. ADG901/ADG902/ADG918/ADG919 Silkscreen Rev. B | Page 3 of 4 UG-676 UG-676 EVAL-ADG901EBZ/EVAL-ADG902EBZ/EVAL-ADG918EBZ/EVAL-ADG919EBZ User Guide ORDERING INFORMATION BILL OF MATERIALS Table 3. Item 1 2 3 4 Qty 1 7 2 1 Reference U1 J1 to J7 C1, C2 C4 Description ADG901/ADG902/ADG918/ADG919 SMA end launch connectors 0.062" 10 pF ceramic capacitor 10 μF tantalum capacitor Supplier/No. Analog Devices, Inc. J502-ND FEC 499-110 FEC 643-683 REVISION HISTORY 4/14—Rev. A to Rev. B Updated Format .................................................................. Universal Changes to ADG918/ADG919 Section ......................................... 3 2003—Rev. A ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2003–2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG12159-0-4/14(B) Rev. B | Page 4 of 4