EVAL-ADM1067TQEBZ

EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide UG-063 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluating the ADM1062 to ADM1169 for Complex Sequencing FEATURES RELATED DOCUMENTS Full-featured evaluation kits for ADM1062 to ADM1169 I²C interface supports all product-related software 10 adjustable voltages reference for input emulation Switch-controlled, open-drain/push-pull digital inputs Extra headers for easy probing Includes point to point patch cables for easy wiring Multiboard cascade support ADM1062 to ADM1169 data sheets EVALUATION KIT CONTENTS EVAL-ADM1062CASZ to EVAL-ADM1169CASZ evaluation board samples of the relevant device are included ADM1062 to ADM1169 device socket 8-way, 150 mm Micromatch ribbon cable Patch cables ADDITIONAL EQUIPMENT NEEDED USB-to-I²C dongle USB-SDP-CABLEZ 9 V to 14.4 V power supply SOFTWARE NEEDED ADM1062 to ADM1169 evaluation software GENERAL DESCRIPTION This user guide describes how to use the ADM1062 to ADM1169 evaluation kits. The kits provide all of the support circuitry required to operate the ADM1062/ADM1063/ ADM1064/ADM1065/ADM1066/ADM1067/ADM1068/ ADM1069/ADM1166/ADM1168/ADM1169 (hereafter referred to as ADM1062 to ADM1169) in their various modes and configurations, including multiple board setups. The ADM1062 to ADM1169 data sheets, available at www.analog.com, provide additional information, and should be consulted when using the evaluation board. All documents and software tools are available at www.analog.com/power-management. Note that USB-SDP-CABLEZ is not included in the evaluation kit and should be ordered separately. Only one dongle is required in multiboard cascade setup. One device socket is included in each kit. Sockets for different device packages are not included. Refer to the Socket Selection Guide section for details regarding the corresponding socket types. EVALUATION KIT SELECTION GUIDE Table 1. Contents of Available Evaluation Kits Evaluation Kit Model EVAL-ADM1062TQEBZ EVAL-ADM1063TQEBZ EVAL-ADM1064TQEBZ EVAL-ADM1065TQEBZ EVAL-ADM1066TQEBZ EVAL-ADM1067TQEBZ EVAL-ADM1068LQEBZ EVAL-ADM1069LQEBZ EVAL-ADM1166TQEBZ EVAL-ADM1168LQEBZ EVAL-ADM1169LQEBZ Contains Evaluation Board EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ EVAL-ADM1062-69CASZ PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Contains IC Socket SOCKET-ADM106xTQZ SOCKET-ADM106xTQZ SOCKET-ADM106xTQZ SOCKET-ADM106xTQZ SOCKET-ADM106xTQZ SOCKET-ADM106xTQZ SOCKET-ADM106xLQZ SOCKET-ADM106xLQZ SOCKET-ADM106xTQZ SOCKET-ADM106xLQZ SOCKET-ADM106xLQZ Rev. C | Page 1 of 20 Corresponding Devices ADM1062ASUZ ADM1063ASUZ ADM1064ASUZ ADM1065ASUZ ADM1066ASUZ ADM1067ASUZ ADM1068ASTZ ADM1069ASTZ ADM1166ASUZ ADM1168ASTZ ADM1169ASTZ UG-063 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide TABLE OF CONTENTS Features .............................................................................................. 1 I²C Interface ...................................................................................4 Evaluation Kit Contents ................................................................... 1 Multiple Board Setup ....................................................................4 Additional Equipment Needed ....................................................... 1 Switch, Jumper, and LED Functions ...........................................5 Related Documents .......................................................................... 1 Socket Selection Guide .................................................................8 Software Needed ............................................................................... 1 Margining Guide ...............................................................................9 General Description ......................................................................... 1 Evaluation Kit Quick Start Guide................................................. 10 Evaluation Kit Selection Guide ....................................................... 1 Hardware Setup .......................................................................... 10 Revision History ............................................................................... 2 Software Setup ............................................................................ 11 Evaluation Board Hardware ............................................................ 3 Demo 1 ........................................................................................ 12 Supported Devices ........................................................................ 3 Demo 2 ........................................................................................ 13 Power Supplies .............................................................................. 3 Evaluation Board Schematics........................................................ 14 Inputs Emulation .......................................................................... 3 Ordering Information .................................................................... 18 Output Signals............................................................................... 3 Bill of Materials ........................................................................... 18 REVISION HISTORY 4/14—Rev. B to Rev. C Change to Evaluation Kit Contents Section, Additional Equipment Section, and General Description Section ................ 1 Change to I2C Interface Section...................................................... 4 7/13—Rev. A to Rev. B Changes to Power Supplies Section and Figure 1......................... 3 Changes to Demo 2 Section .......................................................... 13 9/11—Rev. 0 to Rev. A Changes to Package Contents Section, changes to General Description Section, and Added Table 1 ....................................... 1 Changes to Output Signals Section and Changes to Figure 1 .... 3 Changes to Figure 2 .......................................................................... 4 Changes to Table 2 ............................................................................ 5 Changes to Table 5 ............................................................................ 7 Added Evaluation Kits Quick Start Guide, added Figure 4 to Figure 16, Renumbered Sequentially ........................................... 10 2/10—Revision 0: Initial Version Rev. C | Page 2 of 20 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide UG-063 EVALUATION BOARD HARDWARE The EVAL-ADM1062-69CASZ evaluation board is designed for advanced evaluation of ADM1062 to ADM1169 SuperSequencer® ICs. The board is easy to use, easy to probe, allows flexible wiring, and offers multiple board cascadability. SUPPORTED DEVICES The evaluation board is designed to support all ADM1062 to ADM1169 devices in various packages. A device socket is generally required for use with this board. Devices can be easily fitted and changed using the ADM1062 to ADM1169 device sockets. Solder pads for a single 48-lead thin, plastic quad flat package (TQFP) is also available on the board, allowing the user to solder parts onto the board. INPUTS EMULATION Ten onboard adjustable voltage regulators from Analog Devices, Inc., provide input supply emulation for all different setups supported by the ADM1062 to ADM1169 devices. Each regulator operates independently and output voltages can be easily adjusted by hand using an on-board rotating potentiometer. Every regulator can be enabled or disabled by the user or by the ADM1062 to ADM1169 device, depending on the jumper configuration. Each regulator has an LED assigned to it to indicate its status. All regulators have a feedback pin that allows the user to evaluate the margining function of the ADM1062 to ADM1169 devices. An additional on-board two-way, push-pull/open-drain switch, S3, can be used by the user to emulate digital inputs, if required. Note the labeling on the board. For example, VP1/VX4 indicates a change in function depending on the ADM1062 to ADM1169 device in use. The text on the left, VP1, is for use with the ADM1062 to ADM1067 and ADM1166, whereas the text on the right, VX4, is for use with the ADM1068/ ADM1069/ADM1168/ADM1169. OUTPUT SIGNALS POWER SUPPLIES The evaluation board can accept 9 V to 14.4 V from a bench power supply through Connector J1 and Connector J2. It also supports a wall-mountable switching power supply with the same voltage range using Connector J3. J3 is grounded in the core and has polarity protection circuits to prevent damage due to incorrect polarity setup. The current consumption of the board depends on the exact configuration but is typically less than 200 mA. PDO output signals from the ADM1062 to ADM1169 devices can be easily wired across to the regulator enable control circuits to control the on-board voltage regulators. This allows the board to perform simulations for real-world sequencing applications. The DAC output signals can also be wired to the feedback node of the regulators to achieve supply margining. The wiring is made easy with the point-to-point patch cables included in the evaluation kit. The user can easily cross link the PDO output to a regulators enable input or connect DAC outputs to a regulator’s feedback node. ADJUSTABLE REGULATORS MULTIBOARD CONNECTOR TEMPERATURE SENSORS DEVELOPMENT AREA Bottom row grounded DAC MARGINING OUTPUTS POWER INPUT 9V TO 14.4V I2C CONNECTOR 08644-001 MULTIBOARD CONNECTOR OPTIONAL DIGITAL INPUT Figure 1. Evaluation Board Wiring with Point-To-Point Patch Cables Rev. C | Page 3 of 20 UG-063 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide I²C INTERFACE The evaluation board supports an I²C interface. The user can connect from the PC USB port to the board using the USBSDP-CABLEZ dongle from Analog Devices. The dongle has internal pull-ups for the SDA and SCL bus. Users can use their own I²C cable. The evaluation board can provide on-board 3.3 V voltage pull-up by populating R21 and R22. The board is compatible with all ADM1062 to ADM1169 evaluation software. MULTIPLE BOARD SETUP Connector J7 and Connector J9, along with the eight-way ribbon cable, allow multiple EVAL-ADM1062-69CASZ boards to be connected together to evaluate complex cascade sequencing setups. Apart from power and I²C signals, the cable also links three independent GPIO signal lines between the two boards that it connects. The user can connect them to the inputs and/or outputs of the ADM1062 to ADM1169 devices to achieve sequencing across multiple boards. This allows multiple ADM1062 to ADM1169 devices to work together to increase the number of supply rails to be sequenced and monitored. Rev. C | Page 4 of 20 08644-002 The connection cable carries both power and I²C communication signals across every board that is connected. The user only needs to connect the power and I²C cable to one board. It is recommended to connect the power supply to the board in the middle of the multiple board setup to avoid uneven power dissipation in the traces/cables. Figure 2. Multiple Boards Connection EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide UG-063 SWITCH, JUMPER, AND LED FUNCTIONS Table 2. Connector Functions Switch S1 S1-A S2 S2-1 S2-2 S3 S3-1 S3-2 S4 S4-1, S4-2 S5 S5-1, S5-2 Description I2C/mode control switch. Position A allows the use of the ADM1063 device. Position B allows the board to be isolated from I2C communications. Position C allows the use of the ADM1062, ADM1064 to ADM1069, ADM1166, ADM1168, and ADM1169 devices. Device address switch. On: Address Pin A0 pulled down to ground. Off: Address Pin A0 pulled up to VDDCAP. On: Address Pin A1 pulled down to ground. Off: Address Pin A1 pulled up to VDDCAP. Optional digital input switch. Use in conjunction with X49. X49 connected: push-pull. X49 disconnected: open-drain. On: X49 pulled to ground. Off: X49 pulled to 3.3 V/high impedance. Use in conjunction with X32. X32 connected: push-pull. X32 disconnected: open-drain. On: X32 pulled to ground. Off: X32 pulled to 3.3 V/high impedance. External Temperature Sensor 1 control switch (for use with the ADM1062 and ADM1063). Both on: External Temperature Sensor 1 connected. Both off: External Temperature Sensor 1 disconnected. External Temperature Sensor 2 control switch (for use with the ADM1063 only). Both on: External Temperature Sensor 2 connected. Both off: External Temperature Sensor 2 disconnected. Default Position C Off Off Disconnected Off Disconnected Off Both off Both off Table 3. Jumper Functions Jumper J13 J6 J20 J23 J26 J29 J14 J32 J35 J38 J11 J12 Corresponding Regulator/Rails VH/VH VX1/VX1 VX2/VX2 VX3/VX3 VX4/NC VX5/NC VP1/VX4 VP2/VP1 VP3/VP2 VP4/VP3 7 V (intermediate) 3.3 V (pull-up) Description Rail isolation jumper. Disconnect to isolate the corresponding regulators from its power supply. Can be used for debug. Rev. C | Page 5 of 20 Default Connected UG-063 Jumper J10 J15 J17 J16 J21 J24 J27 J30 J18 J33 J36 J39 J4 J19 J22 J25 J28 J8 J31 J34 J37 J40 J41 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide Corresponding Regulator/Rails VH ADM1062 to ADM1169 VH pin VH/VH VX1/VX1 VX2/VX2 VX3/VX3 VX4/NC VX5/NC VP1/VX4 VP2/VP1 VP3/VP2 VP4/VP3 VX1/VX1 VX2/VX2 VX3/VX3 VX4/NC VX5/NC VP1/VX4 VP2/VP1 VP3/VP2 VP4/VP3 VXx/VPx/VH PDOx Description Controls the output of the VH regulator. Controls the source voltage connected to the VH pin of the ADM1062 to ADM1169 device. Connect left: connect VH pin to on-board VH regulator. Connect right: connect VH pin directly to board supply. Leave unconnected: leave VH pin unconnected. Regulator control jumpers. Position A: regulator always on. Position B: regulator controlled by the PDO output signal of the ADM1062 to ADM1169. Unplugged: regulator shutdown. Default Connected Regulator output voltage divider control jumpers. Position A: normal regulator output. Position B: 1/3 of normal regulator output. Unplugged: disconnect regulator output. Position A Connect left Position A Connector used for device inputs probing. Connector used for device outputs probing. Table 4. LED Functions LED D3 D4 D6 D7 D8 D9 D5 D10 D11 D12 D2 Rails VH/VH VX1/VX1 VX2/VX2 VX3/VX3 VX4/NC VX5/NC VP1/VX4 VP2/VP1 VP3/VP2 VP4/VP3 Board main power input Description Power indication LEDs. On position indicates voltage on corresponding rail. Rev. C | Page 6 of 20 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide UG-063 Table 5. Patching Through-Hole Connection Points Connection Points VX1/VX1 VX2/VX2 VX3/VX3 VX4/NC VX5/NC VP1/VX4 VP2/VP1 VP3/VP2 VP4/VP3 VH/VH PDO1 PDO2 PDO3 PDO4 PDO5 PDO6 PDO7 PDO8 PDO9 PDO10 EN-VX1/VX1 EN-VX2/VX2 EN-VX3/VX3 EN-VX4/NC EN-VX5/NC EN-VP1/VX4 EN-VP2/VP1 EN-VP3/VP2 EN-VP4/VP3 EN-VH/VH X11 X12 X13 X14 X15 X16 Connected To VX1/VX1 pin of the ADM1062 to ADM1169 VX2/VX2 pin of the ADM1062 to ADM1169 VX3/VX3 pin of the ADM1062 to ADM1169 VX4/NC pin of the ADM1062 to ADM1169 VX5/NC pin of the ADM1062 to ADM1067 and ADM1166 VP1/VX4 pin of the ADM1062 to ADM1169 VP2/VP1 pin of the ADM1062 to ADM1169 VP3/VP2 pin of the ADM1062 to ADM1169 VP4/VP3 pin of the ADM1062 to ADM1067 and ADM1166 VH/VH pin of the ADM1062 to ADM1169 PDO1 pin of the ADM1062 to ADM1169 PDO2 pin of the ADM1062 to ADM1169 PDO3 pin of the ADM1062 to ADM1169 PDO4 pin of the ADM1062 to ADM1169 PDO5 pin of the ADM1062 to ADM1169 PDO6 pin of the ADM1062 to ADM1169 PDO7 pin of the ADM1062 to ADM1169 PDO8 pin of the ADM1062 to ADM1169 PDO9 pin of the ADM1062 to ADM1067 and ADM1166 PDO10 pin of the ADM1062 to ADM1067 and ADM1166 VX1/VX1 regulator VX2/VX2 regulator VX3/VX3 regulator VX4/NC regulator VX5/NC regulator VP1/VX4 regulator VP2/VP1 regulator VP3/VP2 regulator VP4/VP3 regulator VH/VH regulator DAC1 pin of the ADM1062, ADM1066, ADM1067, ADM1069, ADM1166, and ADM1169 DAC2 pin of the ADM1062, ADM1066, ADM1067, ADM1069, ADM1166, and ADM1169 DAC3 pin of the ADM1062, ADM1066, ADM1067, ADM1069, ADM1166, and ADM1169 DAC4 pin of the ADM1062, ADM1066, ADM1067, ADM1069, ADM1166, and ADM1169 DAC5 pin of the ADM1062, ADM1066, ADM1067, ADM1069, and ADM1166 DAC6 pin of the ADM1062, ADM1066, ADM1067, ADM1069, and ADM1166 Rev. C | Page 7 of 20 Description Input connections of the ADM1062 to ADM1169. Output connections of the ADM1062 to ADM1169. Connected to the enable circuit of the regulators; connect to PDO outputs directly to allow the ADM1062 to ADM1169 device to take control of the regulator. DAC outputs of the ADM1062, ADM1066, ADM1067, ADM1069, ADM1166, and ADM1169 DAC outputs of the ADM1062, ADM1066, ADM1067, ADM1069, and ADM1166 UG-063 Connection Points T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 X49 X32 IA IB IC OA OB OC EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide Connected To SET pin of VH/VH regulator (ADP3367) Feedback pin of the VX1/VX1 regulator Feedback pin of the VX2/VX2 regulator Feedback pin of the VX3/VX3 regulator Feedback pin of the VX4/NC regulator Feedback pin of the VX5/NC regulator Feedback pin of the VP1/VX4 regulator Feedback pin of the VP2/VP1 regulator Feedback pin of the VP3/VP2 regulator Feedback pin of the VP4/VP3 regulator S3-1 S3-2 J9 (OA of the connected board) J9 (OB of the connected board) J9 (OC of the connected board) J7 (IA of the connected board) J7 (IB of the connected board) J7 (IC of the connected board) Description Connected to the feedback pin of the regulators; connect to the X11 to X16 inputs for supply margining (see the Margining Guide section). Optional digital inputs can be set as open-drain or push-pull. I/Os for multiple board setup. I/Os for multiple board setup. SOCKET SELECTION GUIDE Table 6. Model SOCKET-ADM106xTQZ SOCKET-ADM106xLFZ SOCKET-ADM106xLQZ SOCKET-ADM1069LFZ Description ADM1062TQ to ADM1166TQ daughter card ADM1062LF to ADM1166LF daughter card ADM1068LQ to ADM1169LQ daughter card ADM1069LF daughter card Rev. C | Page 8 of 20 Corresponding Devices ADM1062 to ADM1067 and ADM1166 in TQFP ADM1062 to ADM1067 and ADM1166 in LFCSP ADM1068, ADM1069, ADM1168 and ADM1169 in LQFP ADM1069 and ADM1169 in LFCSP EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide UG-063 MARGINING GUIDE The ADP3331 LDO is used to provide adjustable VX and VP input voltages. A separate Excel tool has been created for users to calculate the settings for margining function. The feedback topology for this part is different from other regulators (see Figure 3). Another voltage divider is used inside the part to provide feedback voltage to the error amplifier. This causes margining calculation in the ADM1062 to ADM1169 evaluation software tool to be different. Note that closed-loop margining is less affected by this topology, although the margining range may differ from the calculated values in the software tool. For the VH pin, the use of ADP3367 results in the margining functions performing correctly with both open and closed loop. INPUT OUTPUT NONINVERTING WIDEBAND DRIVER ATTENUATION (VBANDGAP /VOUT) COMPENSATION CAPACITOR gm R3 PTAT VOS R4 R1 CLOAD D1 PTAT CURRENT RLOAD R2 ADP3331 GND Figure 3. ADP3331 Functional Diagram Rev. C | Page 9 of 20 08644-003 Q1 UG-063 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide EVALUATION KIT QUICK START GUIDE For ADM1068 to ADM1069 and ADM1168 to ADM1169 Evaluation Kits For ADM1062 to ADM1067 and ADM1166 Evaluation Kits 3. PDO1 PDO2 PDO3 PDO4 PDO5 PDO6 PDO7 PDO8 PDO9 PDO10 EN-VX1/VX1 EN-VX2/VX2 EN-VX3/VX3 EN-VX4/NC EN-VX5/NC EN-VP1/VX4 EN-VP2/VP1 EN-VP3/VP2 EN-VP4/VP3 2. 3. 4. Put jumpers J4, J19, and J22 into Position A. This puts the output of LDOs connected to VXx inputs to a lower voltage range. Remove the jumpers J27 and J30 to disable the LDOs that are not used. Put jumpers J16, J21, J24, J18, J33, J36, and J39 into Position B. This makes the LDOs connected to VXx and VPx inputs enabled by external signals. Use the point-to-point patch cables to connect the PDOx pins to the enable pins of the LDOs as shown in Figure 6. PDO1 PDO2 PDO3 PDO4 PDO5 PDO6 PDO7 PDO8 EN-VX1/VX1 EN-VX2/VX2 EN-VX3/VX3 EN-VX4/NC EN-VX5/NC EN-VP1/VX4 EN-VP2/VP1 EN-VP3/VP2 EN-VP4/VP3 Figure 6. Demo Patch Connection 2 Figure 4. Demo Patch Connection 1 5. 6. 7. 8. 08644-009 2. Put jumpers J4, J19, J22, J25, and J28 into Position A. This puts the output of LDOs connected to VXx inputs to lower voltage ranges. Put jumpers J16, J21, J24, J27, J30, J18, J33, J36, and J39 into Position B. This makes the LDOs connected to VXx and VPx inputs enabled by external signals. Use the point-to-point patch cables to connect the PDOx pins to the enable pins of the LDOs as shown in Figure 4 and Figure 5. 08644-008 1. 1. 08644-010 HARDWARE SETUP Figure 5. Evaluation Kit Quick Start Setup Rev. C | Page 10 of 20 For the ADM1063 evaluation kit, switch S1 to Position A. Keep every other switch and jumper in the default positions. Place the device into the IC socket, and connect the board to the PC using the USB-to-I²C dongle. Apply power to the board. EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide UG-063 SOFTWARE SETUP The software searches for all the ADM1062 to ADM1169 devices connected to the interface. Verify the device and address that appears in the device list and click Continue. 08644-012 3. 4. Figure 8. Device Search 5. Click No in the pop-up window to prevent usage of information from the previous session. 08644-013 2. Download and install the ADM106x and ADM116x SuperSequencer evaluation software from analog.com. The software package includes a GUI evaluation tool, a command-line based Prog106x tool, and USB-to-I²C dongle drivers. Download the Supersequencer quick start demo configurations.zip file; this contains the device configuration files for the demo. There are two demo configurations for each device types, demo1 and demo2. Each configuration is saved in both *.txt and *.hex format. Users can use the GUI evaluation software to load the *.txt file or use the Prog106x tool to load the *.hex file. This user guide describes the former; for details of the Prog106x tool refer to user guide UG-049. Run the GUI ADM106x and ADM116x SuperSequencer evaluation software, and select the appropriate I2C interface, then click Work Online as shown in Figure 7. 08644-011 1. Figure 9. Prevent Usage of Previous Information Figure 7. I2C Interface Select Rev. C | Page 11 of 20 UG-063 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide DEMO 1 1. Use the menu bar and navigate to File->Recall Settings From File, or use the shortcut key Ctrl + R. 4. 08644-014 5. Observe the LEDs on the evaluation board flashing in periodic sequence. The Demo 1 configuration simply uses the timeout exit condition of the sequencing engine to sequence the enable signals of the LDOs. Examine the details of the device outputs configuration and sequencing engine content in the Outputs and Sequencing Engine tabs of the GUI as shown in Figure 13 and Figure 14. Figure 10. Recall Settings Click Recall and then navigate to and select the Demo1 .txt file of the appropriate device. 08644-017 2. 08644-015 Figure 13. Outputs Tab Figure 11. Recall Settings 08644-018 Verify the checksums and click OK. 08644-016 3. Figure 14. Sequencing Engine Tab Figure 12. Verify Checksums Rev. C | Page 12 of 20 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide UG-063 DEMO 2 Use the same method described in the Demo 1 section to load the corresponding Demo 2 configuration .txt file into the device. The sequencing engine configuration in Demo 2 is more complex and closely resembles the setup for a real application. Most of the sequencing engine states use all three exit conditions, namely sequence, timeout, and monitor. The status of each supply being enabled is checked, ensuring that all supplies are powered up to the correct level and are stable before advancing the sequencing engine. Observe the sequencing engine advancement based on the status of the on-board LEDs, or use a DMM to probe each VXx and VPx inputs while tweaking the knob to get the accurate voltage reading. For devices with ADC functions, use the Readback tab to continuously read the voltage level on each inputs as shown in Figure 16. Note that the J4, J19, J22, J25, J28 jumpers may need to be in Position B to achieve low voltage on the VXx inputs. 08644-020 If the supply did not rise to the expected level after the timeout period, the sequencing engine can exit to a user-defined fault state. In each state, the sequencing engine also monitors the status of the supplies being enabled in previous states to ensure the integrity of the supply chain. The status of each inputs can be defined using the Inputs tab shown in Figure 15. In Demo 2, a window comparator is applied to each of the inputs except for VH. Use the knob of on-board potentiometer to adjust the voltages on VXx and VPx inputs to the exact level in order to advance the sequencing engine, starting from VX1. 08644-019 Figure 16. Readback Tab Figure 15. Inputs Tab Rev. C | Page 13 of 20 UG-063 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide EVALUATION BOARD SCHEMATICS 08644-004 Figure 17. Board Schematic 1 Rev. C | Page 14 of 20 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide UG-063 08644-005 Figure 18. Board Schematic 2 Rev. C | Page 15 of 20 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide 08644-006 UG-063 Figure 19. Board Schematic 3 Rev. C | Page 16 of 20 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide UG-063 08644-007 Figure 20. Board Schematic 4 Rev. C | Page 17 of 20 UG-063 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide ORDERING INFORMATION BILL OF MATERIALS Table 7. Reference Designator C1 C7, C8, C10, C13, C14, C18, C19, C21, C22, C24, C25, C27, C28, C30, C31, C33, C34, C36, C37 C3, C4, C9, C11, C15 C6, C12, C16, C20, C23, C26, C29, C32, C35, C38, C39, C40 to C43 C2, C5, C17 D1 D2 to D12 EN-VH/VH, EN-VP1/VX4, EN-VP2/VP1, EN-VP3/VP2, EN-VP4/VP3, EN-VX1/VX1, EN-VX2/VX2, EN-VX3/VX3, EN-VX4/NC, EN-VX5/NC GND, IA, IB, IC J1 J2 J6, J10 to J14, J20, J23, J26, J29, J32, J35, J38 J4, J8, J15 to J19, J21, J22, J24, J25, J27, J28, J30, J31, J33, J34, J36, J37, J39 J3 J40, J41 J5 J7, J9 OA, OB, OC, PDO1 to PDO10 Q1, Q3 Q2, Q5 Q4, Q6 to Q13 R1, R5, R14, R29, R38, R57, R48, R66, R75, R84, R93 R2, R10, R35, R44, R54, R63 R3, R7 R4, R8, R16, R33, R42, R52, R61, R70, R79, R88 R6 R11, R15 R12, R17, R19, R25, R28, R37, R47, R56, R65, R74, R83, R92 R13, R27, R36, R46, R55, R64, R73, R82, R91 R18, R20, R31, R32, R40, R41, R50, R51, R59, R60, R68, R69, R77, R78, R86, R87, R95, R96 Description Aluminum electrolytic capacitor, Case C, 35 V, 10 µF SMD capacitor, 0.47 µF, 20% Manufacturer Panasonic Part Number EEE1VA100SR Stock Code 1 FEC 9697012 Phycomp CC0603MRY5V7BB474 FEC 3188851 16 V SMD tantalum capacitor, 10 µF, 10% SMD capacitor, 220 pF, 5% AVX TAJB106K016R FEC 498-737 Phycomp CC0603JRNPO9BN221 FEC 430948 Capacitor, Case B, 1.0 µF, 35 V, 10% Diode, Schottky, 2 A, 20 V, SMB Green 0805 chip LED Patchwork area, not populated Kemet Vishay Kingbright N/A B45196E6105K209 SL22 KP-2012SGC N/A FEC 9754032 FEC 9550780 FEC 1318243 N/A Plated hole, keep free of solder Red 4 mm banana socket Black 4 mm banana socket 2-pin (0.1" pitch) header and shorting shunt 3-pin (0.1" pitch) header and shorting shunt inserted in Position A N/A Deltron Deltron Harwin N/A 571-0500-01 571-0100-01 M20-9990246, M7566-05 Harwin M20-9990346, M7566-05 N/A FEC 1101127 FEC 1101128 FEC 1022247, FEC 150-411 FEC 1022249, FEC 150-411 2.1 mm dc barrel power connector Header, 1-row, 10-way Header, right angle, 1-row, 3-way 8-way top entry socket (board-toboard) Patchwork area, not populated Transistor, PNP, SOT-23 N-channel, enhancement mode, TMOSFET General-purpose NPN SMD transistor Resistor, RC22H, 0603, 1 kΩ, 1% Cliff Tyco Electronics Harwin Tyco Electronics/ Amp N/A NXP Fairchild DC10A 1-826629-0 M22-2030305 7-215079-8 FEC 224-959 FEC 3418376 FEC 672129 FEC 148593 N/A BC807-40 NDS7002A N/A FEC 1081222 FEC 984-5437 NXP Phycomp BC850C RC0603FR-071KL FEC 1081241 FEC 9238484 Resistor, 0603, 82 kΩ, 1% Resistor, RC22H, 0603, 100 kΩ, 1% 3/8" square (10 mm) single-turn potentiometer, 1 MΩ Resistor, RC22H, 0603, 470 kΩ, 1% Resistor, 110 kΩ , 1% 10 kΩ resistor, 1% Multicomp Phycomp Vishay MC 0.063W 0603 1% 82K RC0603FR-07100KL M63M105KB30T607 FEC 9331573 FEC 9238727 FEC 9608290 Phycomp Multicomp Vishay Dale RC0603FR-07470KL MC 01W 0603 1% 110K CRCW060310K0FKEA FEC 9238808 FEC 9332464 FEC 1469748 Resistor, 0603, 20 kΩ, 1% Multicomp MC 0.063W 0603 1% 20K FEC 9330771 Resistor, 0603, 390 kΩ, 1% Multicomp MC 0.063W 0603 1% 390K FEC 9331166 Rev. C | Page 18 of 20 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide Reference Designator R21, R22 R23, R71, R80, R89 R24, R110, R111 R26, R72, R81, R90 R30, R39, R45, R49, R58, R67, R76, R85, R94 R9, R34, R43, R53, R62 R98, R99, R100 to R109 R97 S1 S2 to S5 SCL, SDA, T4 to T13 U1, U8, U9, U10 to U15 U2, U4 U3 U5 U6 U7 VH/VH, VP1/VX4, VP2/VP1, VP3/VP2, VP4/VP3, VX1/VX1, VX2/VX2, VX3/VX3, VX4/NC, VX5/NC, X11 to X18, X29 to X32, X49, X4432, X4433 X60, X61 1 UG-063 Description DNP Resistor, 0603, 270 kΩ, 1% Resistor, RC21, 0603, 1 MΩ, 5% Resistor, 0603, 75 kΩ, 1% Resistor, 0603, 3.01 kΩ, 1% Manufacturer N/A Multicomp Phycomp Multicomp Vishay Dale Part Number N/A MC 0.063W 0603 1% 270K RC0603JR-071ML MC 0.063W 0603 1% 75K CRCW06033K01FKEA Stock Code 1 Not assembled FEC 9330941 FEC 9233741 FEC 9331522 FEC 1469791 Resistor, 0603, 300 kΩ, 1% Resistor, 0805, 49.9 kΩ, 1% Resistor, RC11, 0805, 0 Ω, 1% DPDT switch 2-way, dual-in-line switch Plated hole, keep free of solder Adjustable LDO regulator LDO Diode, Zener, 27 V, 250 mW 10-pin single-in-line socket terminal strip (eight 10-pin strips required) DNP Voltage regulator, 3.3 V Patchwork area, not populated Multicomp Vishay Dale Phycomp Multicomp Grayhill N/A Analog Devices Analog Devices NXP Tyco MC 0.063W 0603 1% 300K CRCW080549K9FKEA 9233750RL 6MD1S4M2RE 78B02T N/A ADP3331ARTZ ADP3367ARZ BZX84-C27 510-AG91D10-ESL FEC 9330992 FEC 1469934 FEC 9233750RL FEC 1550249 FEC 9479031 N/A ADP3331ARTZ ADP3367ARZ FEC 1081413 FEC 1172526 N/A STMicroelectronics N/A N/A L78L33ACZ N/A Not assembled FEC 1467768 N/A Header, straight, 2-way Tyco 826926-2 FEC 1248140 FEC = Farnell ordering code. Rev. C | Page 19 of 20 UG-063 EVAL-ADM1062TQEBZ – EVAL-ADM1169LQEBZ User Guide NOTES I2C refers to a communications protocol originally developed by Philips Semiconductor (now NXP Semiconductors). ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2010–2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG08644-0-4/14(C) Rev. C | Page 20 of 20