EVAL-ADM3054EBZ

Evaluation Board User Guide UG-358 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluation Board for the ADM3054 5 kV rms Signal Isolated High Speed CAN Transceiver with Bus Protection FEATURES GENERAL DESCRIPTION Easy evaluation of the ADM3054 controller area network (CAN) transceiver Isolated ground planes (logic side and bus side) Convenient connections through screw terminal blocks 3.3 V or 5 V power on the logic side (VDD1) 5 V power on the bus side (VDD2) Ground on logic side (GND1) and bus side (GND2) Logic signals: RXD, TXD, VDD2SENSE Cable shield and bus signals: CANH and CANL Jumper-selectable SMB jack inputs for RXD and TXD Test points for measuring all signals Termination resistors (2 × 30 Ω) with common-mode filter The EVAL-ADM3054EBZ allows quick and easy evaluation of the ADM3054 isolated CAN transceiver. The evaluation board allows all of the input and output functions to be exercised without the need for external components. Screw terminal blocks provide convenient connections for logic signals and power. The main device on the evaluation board, the ADM3054, is a controller area network (CAN) physical layer transceiver with integrated digital isolation, allowing a protocol layer CAN controller to access the physical layer bus. The ADM3054 complies with the ISO 11898 standard. It is capable of running at data rates of up to 1 Mbps. The evaluation board has separate ground and power planes for the logic side and the bus side. This allows evaluation of the isolation capability of the ADM3054, which employs Analog Devices, Inc., iCoupler® technology to combine a 3-channel isolator and a CAN transceiver into a single, 16-lead wide body SOIC package. APPLICATIONS ADM3054 part evaluation Evaluation connected to existing CAN controllers/data buses EVALUATION KIT CONTENTS EVAL-ADM3054EBZ The power is isolated between a single 3.3 V or 5 V supply on VDD1, the logic side, and a single 5 V supply provided on VDD2, the bus side. Loss of power on the bus side (VDD2) can be detected by an integrated VDD2SENSE signal. 10397-001 EVAL-ADM3054EBZ Figure 1. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 8 UG-358 Evaluation Board User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Evaluation Board Configuration .....................................................3 Applications ....................................................................................... 1 Setting Up the Evaluation Board .................................................3 Evaluation Kit Contents ................................................................... 1 Evaluation Board Schematic and Layout........................................4 General Description ......................................................................... 1 Ordering Information .......................................................................6 EVAL-ADM3054EBZ....................................................................... 1 Bill of Materials ..............................................................................6 Revision History ............................................................................... 2 Related Links ..................................................................................6 REVISION HISTORY 1/12—Revision 0: Initial Version Rev. 0 | Page 2 of 8 Evaluation Board User Guide UG-358 EVALUATION BOARD CONFIGURATION SETTING UP THE EVALUATION BOARD 500 kHz square wave clock with output swing between 0 V and 5 V. Connect the oscilloscope probes to the CANH and CANL test points. A plot of the oscilloscope for TXD, RXD, CANH, and CANL is shown in Figure 2. Channel 1 shows the TXD signal, Channel 2 and Channel 3 show the CANH and CANL signals, respectively, and Channel 4 shows the RXD signal. The EVAL-ADM3054EBZ allows the ADM3054 isolated CAN transceiver to be quickly and easily evaluated. The evaluation board allows all of the input and output functions to be exercised without the need for external components. On the EVAL-ADM3054EBZ, the power is isolated between a single 3.3 V or 5 V supply on VDD1, the logic side, and a single 5 V supply provided on VDD2, the bus side. When the part is in recessive mode and actively switching states at 1 Mbps, the typical supply current from VDD1 (IDD1) is less than 3 mA. When the part is in the recessive state, the supply current from VDD2 (IDD2) is typically less than 10 mA; in the dominant state, it is typically less than 75 mA; and when actively switching states at 1 Mbps, it is typically less than 55 mA with a default 60 Ω load installed. T 1 4 The bus voltage sense pin (VDD2SENSE), detects when VDD2 is connected on the bus side. A low on VDD2SENSE indicates that power is available on the bus side, and a high on VDD2SENSE indicates that power is absent from the bus side. CH1 2.00V CH3 2.00V VDD1 and VDD2 are the power supplies of the logic and bus sides, respectively. A 22 µF decoupling capacitor, C1, is fitted at the connector between VDD1 and GND1. Capacitors of 100 nF and 1 µF are fitted on the VDD1 and VDD2 pins, respectively, decoupling from GND1 and GND2. CH2 2.00V CH4 2.00V M1.00ms T 50.00% A CH1 1.80V Figure 2. TXD, RXD, CANH, and CANL Signals An example operation of the EVAL-ADM3054EBZ is shown in Figure 3. Connect a signal generator on TXD and set up a 5V POWER SUPPLY SIGNAL GENERATOR GND1 EVAL-ADM3054EBZ J4 J3 VDD2SENSE VDD2 GND2 OSCILLOSCOPE VDD2SENSE J5 RXD LK1 B A RXD J7 A B TXD J6 TXD RXD TXD VDD1 GND1 LK2 CANH CANH CANL VREF SH CANL GND2 GND2 J2 J1 10397-003 3.3V OR 5V POWER SUPPLY Figure 3. Basic Isolated CAN Transceiver Evaluation Board Operation Rev. 0 | Page 3 of 8 10397-002 2 UG-358 Evaluation Board User Guide EVALUATION BOARD SCHEMATIC AND LAYOUT GND1 J3-2 VDD2 J3-1 VDD2SENSE CANH CANL VDD2SENSE B RXD A TXD A J7-2 B C2 100nF VDD1 VDD1 GND1 NC GND1 GND1 VDD2SENSE RXD TXD VDD1 GND1 16 GND2 15 NC 14 NC 13 VDD2 12 CANH 11 CANL 10 VREF 9 GND2 VREF CANH SHIELD CANL GND2 J2-1 J2-2 J2-3 J2-4 ADM3054 VDD2 GND2 GND2 GND2 GND2 J4-2 J4-1 J1-2 GND2 10397-005 Figure 4. EVAL-ADM3054EBZ Schematic Figure 5. EVAL-ADM3054EBZ Silkscreen 10397-006 J1-1 30 C5 DNI GND1 VDD2 GND1 + GND1 VDD1 C3 47nF R1 0R RT2 C1 22uF LK2 J6 Figure 6. EVAL-ADM3054EBZ Component Side Rev. 0 | Page 4 of 8 10397-004 LK1 GND1 J7-1 1 2 3 4 5 6 7 8 30 U1 TXD RT1 J5 C4 1uF RXD UG-358 10397-007 Evaluation Board User Guide Figure 7. EVAL-ADM3054EBZ Solder Side Rev. 0 | Page 5 of 8 UG-358 Evaluation Board User Guide ORDERING INFORMATION BILL OF MATERIALS Table 1. Quantity Reference Designator Description Supplier/Part Number 1 2 1 1 4 2 2 4 1 2 2 1 2 1 2 C1 C2, C4 C3 C5 CANH, TXD, VDD2SENSE, VREF CANL, RXD GND1, GND2 J1, J3, J4, J7 J2 J5, J6 LK1, LK2 R1 RT1, RT2 U1 VDD1, VDD2 Capacitor, tantalum, 22 µF, TAJ_C Capacitor, 100 nF, 0805 Capacitor, 47 nF, 0805 Not placed/optional Test point, yellow Test point, green Test point, black Terminal block, 2-way Terminal block, 4-way Connector, SMB jack 4-pin (2 × 2) 0.1" header and shorting block Resistor, 0 Ω, 0805 Resistor, 30 Ω, 0805 16-lead SOIC, wide body Test point, red AVX Corporation/TAJC226K016RNJ Yageo (Phycomp)/CC0805KRX7R7BB104 Multicomp/MCCA000270 N/A Vero Technologies/20-313140 Vero Technologies/20-313138 Vero Technologies/20-2137 Lumberg/KRM 02 Lumberg/KRM 04 Multicomp/24-14-2-TGG Harwin/M20-9953646 & M7566-05 Vishay Draloric/MC 0.063W 0603 0R Multicomp/MCPWR05FTFW0300 Analog Devices/ADM3054BRWZ Vero Technologies/20-313137 RELATED LINKS Resource ADM3054 Description Product Page, 5 kV rms Signal Isolated High Speed CAN Transceiver with Bus Protection Rev. 0 | Page 6 of 8 Evaluation Board User Guide UG-358 NOTES Rev. 0 | Page 7 of 8 UG-358 Evaluation Board User Guide NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG10397-0-1/12(0) Rev. 0 | Page 8 of 8