Evaluation Board User Guide
UG-176
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
ADuC7023 Evaluation Board User Guide
MicroConverter ADuC7023 Development System
FEATURES
GENERAL DESCRIPTION
2-layer printed circuit board (PCB), 4 inch × 5 inch form factor
USB power supply regulated to 3.3 V on board
USB-to-I2C programming interface on board
20-pin standard JTAG connector for programming/
debugging
Demonstration circuit
32.768 kHz watch crystal to drive the PLL clock
ADR291 2.5 V external reference chip
Reset/download/IRQ0 push buttons
Power indicator/general-purpose LEDs
Access to all ADC inputs and DAC outputs from external header;
all device ports are routed to external header pins
Surface-mount and through-hole, general-purpose
prototype area
The full evaluation kit also includes:
mIDAS-Link JTAG programming POD
CD containing evaluation software, including user
manuals, data sheets, example code, I2CWSD, and
evaluation compilers
USB cable
This user guide refers to the ADuC7023 evaluation boards
provided in the EVAL-ADuC7023QSPZ (32-lead LFCSP device
based) and the EVAL-ADuC7023QSPZ1 (40-lead LFCSP device
based) kits. These evaluation boards allow for the evaluation of
the MicroConverter® ADuC7023. The ADuC7023 contains an
ARM7TDMI core, 64 kB of Flash, 8 kB of SRAM, a 12-bit, 1 MSPS
SAR analog-to-digital converter (ADC), and 4 × 12-bit voltage
digital-to-analog converters (DACs), plus many other features.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
These evaluation boards allow users to program the ADuC7023
via the JTAG or the I2C interfaces. Users may also debug their
source code through the JTAG interface.
In this user guide, all references to the physical orientation of
components on the boards are made with respect to a componentside view of the board with the prototype area appearing in the
bottom of the board.
The boards are laid out to minimize coupling between the analog
and digital sections of the board. To this end, the ground plane
is split with the analog section on the left side and a digital
plane on the right side of the board. The regulated 3.3 V power
supply is routed directly to the digital section and is filtered
before being routed into the analog section of the board.
Rev. 0 | Page 1 of 16
UG-176
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
General-Purpose Prototype Area................................................5
General Description ......................................................................... 1
DIP Switch Link Options .................................................................6
Revision History ............................................................................... 2
External Connectors .........................................................................7
Evaluation Board Features ............................................................... 3
Analog I/O Connector, J3 ............................................................7
Power Supply ................................................................................. 3
Emulation Connector, J4 ..............................................................7
2
I C Programming Interface ......................................................... 3
Mini-USB Interface Connector, J1 ..............................................7
Emulation Interface ...................................................................... 4
Digital I/O Connector, J2 .............................................................7
2
Using P0.4 and P0.5 as I C Pins .................................................. 4
I2C Connector, J9 ...........................................................................7
Crystal Circuit............................................................................... 4
Evaluation Board, Schematics and Artwork ..................................8
External Reference (ADR291E) .................................................. 4
Ordering Information .................................................................... 14
Reset/Download/IRQ1 Push-Buttons ....................................... 4
Bill of Materials ........................................................................... 14
Power Indicator/General-Purpose LEDs .................................. 5
Related Links ............................................................................... 15
Analog I/O Connections ............................................................. 5
REVISION HISTORY
7/10—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
Evaluation Board User Guide
UG-176
EVALUATION BOARD FEATURES
POWER SUPPLY
Both boards can be directly powered via the mini-USB connector,
J1. Alternatively, an external 12 V to 5 V power supply can be
connected to the 2-pin header, J7, which is labeled POWER.
The pin beside the mini-USB connector is the power pin.
I2C PROGRAMMING INTERFACE
09195-002
The ADuC7023 is connected to the USB connector via the
I2C-to-USB transceiver chip referenced as U5 on the PCB. The
interface allows direct connection to the PC via the USB port.
Connect the evaluation board to the PC via the USB port using
the mini-USB lead included in the evaluation package.
Prompts appear to install drivers for the new hardware, which
includes the following: Serial Converter A, Serial Converter B, and
the serial ports. The D2XX direct drivers can be found on the
FTDI website. These drivers are also included on the CD with the
evaluation kit.
Figure 2. I2CWSD Dialog Box
3.
Click Configure and select the settings shown in Figure 3.
Complete the following steps to install the drivers for the
FT2232H device on the evaluation board and to download a
hex file to the ADuC7023 internal flash via the I2CWSD
application provided with the evaluation software.
Select Install the software automatically (Recommended)
and Click Next > to complete the install (see Figure 1).
09195-003
1.
Figure 3. I2CWSD Configure Options
4.
Select the hex files location by clicking Browse.. and reset the
evaluation board. This is done by holding down the
SERIAL DOWNLOAD button (S2), toggling the RESET
button (S3), and releasing the SERIAL DOWNLOAD
switch, which then resets the board (see Figure 4).
(C) PUSH S3
S2
S3
S3
S2
S3
S2
(RESET = 1)
(SERIAL
(RESET = 1)
(SERIAL
(RESET = 0)
(SERIAL
DOWNLOAD = 1)
DOWNLOAD = 0)
DOWNLOAD = 0)
Figure 1. Found New Hardware Wizard Dialog Box
2.
(B) PUSH S2
To connect to the Microcontroller, open the I2CWSD
application from the Windows® Start menu (see Figure 2).
This may also be downloaded from the ADuC7023 product
page on the Analog Devices, Inc., website. This I2CWSD is
different from the generic I2CWSD application that interfaces
to the USB-I2C/LIN-CONVZ dongle.
Rev. 0 | Page 3 of 16
(D) RELEASE S3
S3
S2
(RESET = 1)
(SERIAL
DOWNLOAD = 0)
(E) RELEASE S2
S3
(RESET = 1)
S2
(SERIAL
DOWNLOAD = 1)
Figure 4. Download Mode Entry Sequence
09195-004
09195-001
(A) S3 AND S2 RELEASED
UG-176
Click Start in the I2CWSD dialog box to connect the
I2CWSD download software with the ADuC7023 bootloader
(see Figure 5).
09195-013
5.
Evaluation Board User Guide
Figure 7. Command to Enter to Run Reset_Ft2232h_Io.exe
09195-005
Go to the directory where the Reset_Ft2232h_Io.exe utility is
copied on the PC (see Figure 7 and Figure 8).
Figure 5. I2CWSD Application Showing a Valid ADuC7023 ID String Response
EMULATION INTERFACE
09195-014
Nonintrusive emulation and download are possible on the
ADuC7023 via JTAG by connecting a JTAG emulator to the J4
connector.
USING P0.4 AND P0.5 AS I2C PINS
The ADuC7023 evaluation boards use an I2C-to-USB transceiver
chip, the FT2232H, that allows the ADuC7023 to be programmed
directly over the USB interface without any need of an external
dongle. However, the FT2232H does drive the P0.4/P0.5 pins of
the ADuC7023 by default. To isolate these pins from the FT2232H,
run the Reset_Ft2232h_Io.exe utility, which can be downloaded
from the ADuC7023 product page on the Analog Devices website.
Figure 8. Expected Text after Running Reset_Ft2232h_Io.exe
CRYSTAL CIRCUIT
The board is fitted with a 32.768 kHz crystal, from which the
on-chip PLL circuit can generate a 41.78 MHz clock.
EXTERNAL REFERENCE (ADR291E)
This utility configures the P0.4/P0.5 connection to the FT2232H as
input pins, which stops the FT2232H from driving these pins.
The external 2.5 V reference chip, U2, is provided on the
evaluation board to demonstrate the external reference option
of the ADuC7023.
Execute this utility if the P0.4/P0.5 pins are intended for any use
other than interfacing with the PC via the USB transceiver.
RESET/DOWNLOAD/IRQ1 PUSH-BUTTONS
Run the executable from the Command window, as shown in
Figure 6.
A reset push button is provided to allow users to reset the part
manually. When pressed, the RST pin of the ADuC7023 is pulled
to DGND. Because the RST pin on the ADuC7023 is Schmidttriggered internally, there is no need to use an external Schmidt
trigger on this pin.
09195-012
When pressed, the IRQ1 push-button switch drives the P1.1 pin
high. This can be used to initiate an External Interrupt 1.
On the evaluation board, serial download mode can be easily
initiated by holding down the SERIAL DOWNLOAD push button
(S2) while pressing and releasing the RESET button (S3), as
shown in the I2C Programming Interface section. Also, ensure
that Flash Address 0x80014 contains 0xFFFFFFFF.
Figure 6. How to Open a Command Window
Rev. 0 | Page 4 of 16
Evaluation Board User Guide
UG-176
POWER INDICATOR/GENERAL-PURPOSE LEDS
A power LED (D5) is used to indicate that a sufficient supply is
available on the board. A general-purpose LED (D2) is directly
connected to VDDIO and connected to P0.7 of the ADuC7023
through R18. When P0.7 is cleared, the LED turns on. When
P0.7 is set, the LED turns off.
ANALOG I/O CONNECTIONS
All analog I/O connections are connected to Header J3.
ADC0 and ADC1 are buffered using an AD8606 to evaluate
single-ended and pseudo differential mode. A potentiometer
can be connected to ADC0 buffered.
ADC3 and ADC2 can be buffered with a single-ended-todifferential op amp on board, with the AD8132 used to
evaluate the ADC in differential mode.
DAC1 can be used to control the brightness of the green LED, D1,
when connected via the S1 switch.
GENERAL-PURPOSE PROTOTYPE AREA
General-purpose prototype areas are provided at the bottom of the
evaluation board for adding external components as required in
the application. As can be seen from the layout, AVDD, AGND,
VDDIO, and DGND tracks are provided in this prototype area
(see the Evaluation Board, Schematics and Artwork section).
Rev. 0 | Page 5 of 16
UG-176
Evaluation Board User Guide
DIP SWITCH LINK OPTIONS
Table 1.
Option
S1-1 VREF
Function
Connects VOUT of the ADR291E to the VREF pin.
S1-2 VOCM
Connects VOUT of the ADR291E to VOCM.
S1-3 POT
Connects POT output to the noninverting input of U4-A, the
input buffer for ADC0.
S1-4 ADC3
Connects ADC3, J3 (Pin 8), to B_ADC3.
S1-5 ADC3
Connects V+ output of the differential amplifier, U3, to the
ADC3 input.
S1-6 ADC2
Connects V− output of the differential amplifier, U3, to the
ADC2 input.
S1-7 ADC2
S1-8 DAC1
Not used
Connects DAC1 to D1 for the LED demonstration circuit.
Rev. 0 | Page 6 of 16
Use
Slide S1-1 to the on position to connect VOUT of the ADR291E
to VREF.
Slide S1-1 to the off position to disconnect VOUT of the
ADR291E from VREF.
Slide S1-2 to the on position to connect VOUT of the ADR291E
to VOCM.
Slide S1-2 to the off position to disconnect VOUT of the
ADR291E from VOCM.
Slide S1-3 to the on position to connect POT to ADC0.
Slide S1-3 to the off position to disconnect POT from ADC0.
Slide S1-4 to the on position to connect ADC3, J3 (Pin 8), to
B_ADC3.
Slide S1-4 to the off position to disconnect ADC3, J3 (Pin 8),
from B_ADC3.
Slide S1-5 to the on position to connect the V+ output of the
AD8132 differential amplifier to ADC3.
Slide S1-5 to the off position to disconnect the V+ output of
the AD8132 differential amplifier from ADC3.
Slide S1-6 to the on position to connect the V− output of the
AD8132 differential amplifier to ADC2.
Slide S1-6 to the off position to disconnect the V− output of
the AD8132 differential amplifier to ADC2.
Not used.
Slide S1-8 to the on position to connect DAC1 to D1.
Slide S1-8 to the off position to disconnect DAC1 from D1.
Evaluation Board User Guide
UG-176
EXTERNAL CONNECTORS
ANALOG I/O CONNECTOR, J3
The analog I/O connector, J3, provides external connections for
all ADC inputs, reference inputs, and DAC outputs. The pinout
of the connector is shown in Table 2.
Both evaluation board versions have the same pinout.
Table 2. Pin Functions for Analog I/O Connector, J3
Pin Number
J3-1
J3-2
J3-3
J3-4
J3-5
J3-6
J3-7
J3-8
J3-9
J3-10
J3-11
J3-12
J3-13
J3-14
J3-15
J3-16
J3-17
J3-18
J3-19
J3-20
Pin Function
AVDD
AGND
VREF
AGND
POT
ADC1
ADC2
ADC3
AVDD
AGND
AGND
AGND
DIFF
V0CM
DAC0
DAC1
DAC2
DAC3
AGND
AGND
Table 3. Pin Functions for the Digital I/O Connector, J2, on the
32-Pin Evaluation Board
Pin No.
J2-1
J2-2
J2-3
J2-4
J2-5
J2-6
J2-7
J2-8
J2-9
J2-10
J2-11
J2-12
J2-13
J2-14
Pin Function
DGND
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
P1.0
P1.1
P1.2
P1.3
VDDIO
Table 4. Pin Functions for the Digital I/O Connector, J2, on the
40-Pin Evaluation Board
The digital I/O connector, J2, provides external connections for
all GPIOs. The pinout of the connector is shown in Table 3 and
Table 4 for the 32-pin and 40-pin boards, with details of the pin
functions.
Pin No.
J2-1
J2-2
J2-3
J2-4
J2-5
J2-6
J2-7
J2-8
J2-9
J2-10
J2-11
J2-12
J2-13
J2-14
J2-15
J2-16
J2-17
J2-18
J2-19
J2-20
J2-21
J2-22
I2C CONNECTOR, J9
Table 5. Pin Functions for Analog I/O Connector, J9
Connector J9 provides duplicate external connections from the
digital I/O. Table 5 provides further details.
Pin No.
J9-1
J9-2
J9-3
J9-4
EMULATION CONNECTOR, J4
Connector J4 provides a connection of the evaluation board to
the PC via a JTAG emulator.
MINI-USB INTERFACE CONNECTOR, J1
Connector J1 provides power and a simple connection of the
evaluation board to the PC via a USB cable provided with the
ADuC7023 development system.
DIGITAL I/O CONNECTOR, J2
Rev. 0 | Page 7 of 16
Pin Function
DGND
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
P1.0
P1.1
P1.2
P1.3
P2.4
P1.4
P1.5
P1.6
P1.7
P2.0
P2.2
P2.3
VDDIO
Pin Function
DGND
P0.5
P0.4
VDDIO
UG-176
Evaluation Board User Guide
09195-006
EVALUATION BOARD, SCHEMATICS AND ARTWORK
Figure 9. EVAL-ADuC7023QSPZ1, 40-Lead LFCSP Evaluation Board Artwork
Rev. 0 | Page 8 of 16
UG-176
09195-007
Evaluation Board User Guide
Figure 10. EVAL-ADuC7023QSPZ, 32-Lead LFCSP Evaluation Board Artwork
Rev. 0 | Page 9 of 16
UG-176
Evaluation Board User Guide
09195-008
Figure 11. EVAL-ADuC7023QSPZ, 32-LFCSP Evaluation Board Schematic, Page1
Rev. 0 | Page 10 of 16
Evaluation Board User Guide
UG-176
09195-011
Figure 12. EVAL-ADuC7023QSPZ, 32-LFCSP Evaluation Board Schematic, Page2
Rev. 0 | Page 11 of 16
UG-176
Evaluation Board User Guide
09195-010
Figure 13. EVAL-ADuC7023QSPZ1, 40-LFCSP Evaluation Board Schematic, Page1
Rev. 0 | Page 12 of 16
Evaluation Board User Guide
UG-176
09195-011
Figure 14. EVAL-ADuC7023QSPZ1, 40-LFCSP Evaluation Board Schematic, Page2
Rev. 0 | Page 13 of 16
UG-176
Evaluation Board User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 6.
Name
C1, C5, C13, C15, C18
C2 to C4, C6, C12, C14, C16,
C17, C22, C23, C26, C33 to C41
C7, C8
C9, C10
C11, C19
C20, C21
C24, C25, C28 to C32
C27, C42
D1, D2, D5
J1
J2
Value 1
10 μF
0.1 μF
Part Description
10 V SMD tantalum capacitors
Multilayer ceramic capacitors, 0603, 25 V
Manufacturer1
AVX
AVX
Part No.1
FEC 197-130
FEC 317-287
22 pF
10 nF
470 nF
12 pF
4.7 μF
27 pF
N/A
N/A
N/A
Multilayer ceramic capacitors, 0603, 50 V
Multilayer ceramic capacitors, 0603, 25 V
Multilayer ceramic capacitors, 0603, 16 V
Multilayer ceramic capacitors, 0603, 50 V
Capacitors, Case A, 16 V
Capacitors, 0603, 50 V
Green SMD LEDs
USB mini-B connector (USB-OTG)
SIP-14P_SMD, surface-mount terminal strip
FEC 722-005
FEC 301-9561
FEC 318-8851
FEC 721-979
FEC 197269
FEC 722017
FEC 4134436
FEC 9786490
TSM-114-01-T-SV
J3
N/A
SIP-20P_SMD, surface-mount terminal strip
J4
J7
J9
N/A
N/A
N/A
20-pin (2 × 10) SMT shrouded header
Not populated
4-pin inline header; 100 mil centers
L1, L3 to L5
L2
N/A
600 Ω
Ferrite beads, 2012 case
Inductor, SMD
R1
R2
R3
R4
R5, R6, R8, R9
R7
R10, R11
R12
R13, R14, R15, R20, R24, R25,
R33 to R38, R40
R16, R17, R31
R18
R19
R21 to R23
R26
R27
R28, R32
R29, R39
R30
S1
S2 to S4
10 kΩ
100 Ω
200 Ω
49.9 Ω
348 Ω
24.9 Ω
60.4 Ω
270 Ω
0Ω
Trimmer, SMD
SMD resistor, 0805
SMD resistor, 0805
SMD resistor, 0603, 1%
SMD resistors, 0603, 1%
SMD resistor, 0603, 1%
SMD resistors, 0603, 1%
SMD resistor, 0603, 1%
SMD resistors, 0603
Phycomp (Yageo)
Phycomp (Yageo)
Phycomp (Yageo)
Phycomp (Yageo)
AVX
Phycomp (Yageo)
Avago Technologies
Molex
Samtec
(Sable Electronics)
Samtec
(Sable Electronics)
Samtec
N/A
Samtec
(Sable Electronics)
TDK
Murata
Manufacturing Co.
Vishay Sfernice
Multicomp
Multicomp
Yageo
Yageo
Yageo
Yageo
Multicomp
Multicomp
1 kΩ
470 Ω
4.7 kΩ
100 kΩ
560 Ω
1.5 Ω
7.5 Ω
4.7 kΩ
12 kΩ
SMD resistors, 0603, 1%
SMD resistor, 0603, 1%
SMD resistor, 0603, RC21
SMD resistors, 0603, 1%
Resistor, 0603, 1%
Resistor, 0603, 5%
Resistor, 0603, 1%, 50 ppm
SMD resistor, RC21, 0603
Resistor, RC21, 0603
8-position switch (sealed), SMD
Switch SMD, SPNO
Multicomp
Vishay Draloric
Phycomp (Yageo)
Multicomp
Multicomp
Multicomp
Phycomp (Yageo)
Phycomp (Yageo)
Phycomp (Yageo)
Grayhill, Inc.
OMRON Corporation
FEC 9330380
FEC 1469815
FEC 9233466
FEC 9330402
FEC 9331344
FEC 9331832
FEC 1527233
FEC 9233466
FEC 9233512
Digi-Key GH7242-ND
FEC 177807
N/A
Rev. 0 | Page 14 of 16
TSM-120-01-T-SV
HTST-110-01-L-DV
N/A
TSM-104-01-T-SV
FEC 1301672
FEC 9526862
FEC 1141485
FEC 933-2375
FEC 9332758
Digi-Key 311-49.9HRCT-ND
Digi-Key 311-348HRCT-ND
Digi-Key 311-24.9HRCT-ND
Digi-Key 311-60.4HRCT-ND
FEC 9330917
FEC 9331662
Evaluation Board User Guide
UG-176
Name
U1
Value 1
N/A
U2
N/A
U3
U4
N/A
N/A
U5
N/A
U7, U8
N/A
Y1
32.768 kHz
Part Description
Precision analog microcontroller,
12-bit analog I/O, ARM7TDMI MCU
Low noise micropower precision
voltage reference (2.5 V)
Low cost, high speed differential amplifier
Precision, low noise, CMOS, rail-to-rail,
input/output operational amplifier (dual)
Dual high speed USB to multipurpose
UART/FIFO IC
High accuracy ultralow IQ, 300 mA,
anyCAP® low dropout regulator
SMD crystal
Y2
12 MHz
Crystal, 16 pF through hole
1
Manufacturer1
Part No.1
ADuC7023
Analog Devices, Inc.
ADR291ERZ
Analog Devices, Inc.
Analog Devices, Inc.
AD8132ARMZ
AD8606ARZ
FTDI
FT2232HL
Analog Devices, Inc.
ADP3333ARM-3.3Z
IQD Frequency
Products
ABRACON
FEC 9713220
FEC 7942060
N/A is not applicable.
RELATED LINKS
Resource
ADuC7023
EVAL-ADuC7023QSPZ
EVAL-ADuC7023QSPZ1
ADR291
AD8606
AD8132
Description
Product Page, Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI MCU
32-Lead LFCSP ADuC7032 Evaluation Board
40-Lead LFCSP ADuC7032 Evaluation Board
Product Page, Low Noise Micropower Precision Voltage Reference (2.5 V)
Product Page, Precision, Low Noise, CMOS, Rail-To-Rail, Input/Output Operational Amplifier (Dual)
Product Page, Low Cost, High Speed Differential Amplifier
Rev. 0 | Page 15 of 16
UG-176
Evaluation Board User Guide
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG09195-0-7/10(0)
Rev. 0 | Page 16 of 16
工商网监
湘ICP备2023018690号
