Evaluation Board User Guide
UG-403
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluating the iCoupler ADuM4070 Isolated Switching Regulator
with Integrated Feedback
FEATURES
GENERAL DESCRIPTION
ADuM4070 circuit, including 5 kV rms isolated dc-to-dc
converters
Single supply (default)
5 V input to 5 V output (regulated)
Reconfigurable to 5 V input to 3.3 V output or
3.3 V input to 3.3 V output
Double supply
5 V input to 15 V output (regulated) and 7.5 V output
(unregulated)
Reconfigurable to 5 V input to 12 V output (regulated)
and 6 V output (unregulated)
Footprints for Coilcraft, Inc., and Halo Electronics, Inc.,
transformer options
Multiple switching frequency options
The EVAL-ADuM4070EBZ can be used for different applications
of the ADuM4070 isolated switching regulator. With the ability
to be configured as a circuit with either single- (default) or
double-supply output, the board supports a variety of input/output
configurations and multiple transformer options. It is equipped
with an ADuM4070 regulator for voltage isolation; the regulator
features integrated feedback and a switching frequency that can be
set from 200 kHz to 1000 kHz.
This user guide provides all the necessary details to set up and
use the EVAL-ADuM4070EBZ board. Additional information
about the ADuM4070 device is available in the ADuM4070 data
sheet, which should be consulted in conjunction with this user
guide when using the EVAL-ADuM4070EBZ board.
SUPPORTED iCoupler MODELS
ADuM4070
10663-001
ADuM4070 EVALUATION BOARD PHOTOGRAPH
Figure 1. Single-Supply and Double-Supply Configurations
See the last page for an important warning and disclaimers.
Rev. 0 | Page 1 of 12
UG-403
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Other Input and Isolated Output Supply Options ....................5
Supported iCoupler Models ............................................................ 1
Double Supply ....................................................................................7
General Description ......................................................................... 1
Terminals ........................................................................................7
ADuM4070 Evaluation Board Photograph ................................... 1
Transformer Selection ..................................................................7
Revision History ............................................................................... 2
Switching Frequency Options......................................................7
Configuring the Board for Single- or Double-Supply Output ... 3
Other Secondary Isolated Supply Configurations ....................8
Single Supply ..................................................................................... 4
Evaluation Board Schematic and Artwork.....................................9
Terminals ....................................................................................... 4
Evaluation Board Layout ..............................................................9
Transformer Selection .................................................................. 5
Bill of Materials ............................................................................... 10
Switching Frequency Options ..................................................... 5
REVISION HISTORY
3/13—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
Evaluation Board User Guide
UG-403
CONFIGURING THE BOARD FOR SINGLE- OR DOUBLE-SUPPLY OUTPUT
The ADuM4070 evaluation board can be configured for an isolated
circuit with either single- or double-supply output. See Table 1 for
information about the setup of the feedback divider resistors for
the single- and double-supply configurations. For additional applications information about the ADuM4070 in these configurations,
see the ADuM4070 data sheet. Figure 12 shows the schematic for
the EVAL-ADuM4070EBZ board in single- and double-supply
configurations.
Table 1. Feedback Divider Resistors Configuration
Configuration
3.3 V Single
5 V Single
12 V Double
15 V Double
R6
17.4 kΩ
17.4 kΩ
90.9 kΩ
90.9 kΩ
R10
0Ω
Open
0Ω
Open
R11
14.3 kΩ
14.3 kΩ
24.9 kΩ
24.9 kΩ
R15
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
The single- or double-supply configuration can be selected by
changing the output mode resistor values as described in Table 2.
Table 2. Output Mode Resistors Configuration
Configuration
3.3 V/5 V Single
12 V/15 V Double
±15 V Double
R5
Open
0Ω
Open
R7
0Ω
Open
0Ω
R8
Open
0Ω
Open
R9
0Ω
Open
0Ω
R19
0Ω
Open
Open
After setting the feedback divider and output mode resistors,
refer to the Single Supply or Double Supply section for additional
information about configuring the EVAL-ADuM4070EBZ board.
Rev. 0 | Page 3 of 12
UG-403
Evaluation Board User Guide
SINGLE SUPPLY
The ADuM4070 switching regulator on this evaluation board
is configured by default for single-supply output. When the
ADuM4070 is set to single-supply mode, the feedback divider
resistors should be configured as described in Table 1 and the
output mode resistors should be configured as described in
Table 2.
By default, the single-supply configuration provides a 5 V
secondary isolated supply with a 5 V primary input supply,
which can provide up to 2.5 W of regulated, isolated power. The
single supply can be reconfigured as a 3.3 V secondary isolated
supply with a 5 V or 3.3 V primary input supply. See the Other
Input and Isolated Output Supply Options section for more
information.
TERMINALS
In the single-supply configuration, the EVAL-ADuM4070EBZ
board has terminal blocks on Side 1 (the primary/power supply
input side) and Side 2 (the secondary/power supply output side).
An 8.0 mm isolation barrier separates Side 1 from Side 2. Figure 2
shows the location of these terminals.
Input Power Connections
Connect 5 V to P1, labeled 5V (or connect 3.3 V to P1 for a 3.3 V
primary input supply with a 3.3 V secondary isolated supply).
Connect the negative end of the supply to P2, labeled GND.
These are the only off-board connections required for the board
to function in single-supply configuration.
VDD1 is the ADuM4070 transformer driver supply, and VDDA is
the primary supply voltage (see the ADuM4070 data sheet for
additional information). VDD1 and VDDA are bypassed by a 47 µF
ceramic capacitor (C3) and a 0.1 µF local bypass capacitor (C8)
located close to the ADuM4070. R4, R3, C4, and C5 are provided
for an optional and unpopulated snubber, which can be used to
reduce radiated emissions.
Power is transferred to Side 2 by a regulated push-pull converter,
comprising the ADuM4070 (U1), an external transformer (T2
or T3), and other components (see the ADuM4070 data sheet
for an explanation of this circuit functionality).
Table 3 summarizes the functions of the terminal connections.
These connections are described in more detail in the Input
Power Connections and Output Power Connections sections.
Table 3. Single-Supply Terminal Function Descriptions
Label
5V
GND
OUT1
ISO_GND
Description
Side 1—5 V primary input supply
Side 1—ground reference
Side 2—5 V secondary isolated supply
Side 2—ground reference
10663-002
Terminal
P1
P2
P7
P8
Figure 2. Single-Supply and Double-Supply Board Terminals
Rev. 0 | Page 4 of 12
Evaluation Board User Guide
UG-403
Output Power Connections
Table 4. Switching Frequency Selection
An output load can be connected to P7, labeled OUT1, which is the
isolated, regulated 5 V output supply. Connect the return of the
load to P8, labeled ISO_GND, which is the Side 2 ground reference.
Including the current necessary for the ADuM4070 secondary
side (I/O and pulse-width modulation control), this supply can
provide up to 500 mA in the default configuration—a 5 V primary
input supply with a 5 V secondary isolated supply. Figure 4
through Figure 7 show how the efficiency of the power supply
varies with load current, switching frequency, and temperature.
R12
0Ω
Open
0Ω
0Ω
R13
Open
Open
Open
0Ω
R14
Open
0Ω
0Ω
0Ω
ROC
300 kΩ
100 kΩ
75 kΩ
50 kΩ
Switching Frequency (fSW)
200 kHz
500 kHz (default)
700 kHz
1 MHz
1500
1400
1300
1200
TRANSFORMER SELECTION
1100
The resistance connected from the ADuM4070 oscillator control
pin (OC) to ground sets the single-supply switching frequency.
Figure 3 shows the relationship between this resistance and the
converter switching frequency. The EVAL-ADuM4070EBZ can
be configured with 0 Ω, 0603 resistors to set one of four preset
switching frequencies. Table 4 lists the switching frequencies that
can be selected by short- or open-circuiting R12, R13, and R14.
The user can select a different switching frequency by removing
R12 and R13 and then choosing R18 based on Figure 3. The
board is configured for the 500 kHz setting by default. Figure 4 and
Figure 6 show how the switching frequency affects the efficiency of
the supply using a Coilcraft transformer (CR7983-CL) and a Halo
Electronics transformer (TGRAD-560V8LF), respectively. Figure 5
shows how the efficiency curves vary over temperature with a
500 kHz switching frequency.
900
800
700
600
500
400
300
200
100
0
0
50
100
150
200
250
300
350
400
450
500
ROC (kΩ)
NOTES
1. ROC IS A CALCULATED VALUE BASED ON THE SELECTION OF
R12, R13, AND R14.
10663-003
SWITCHING FREQUENCY OPTIONS
fSW (kHz)
The EVAL-ADuM4070EBZ supports multiple transformer
options. In the single-supply configuration, the board is equipped
with a Halo Electronics TGRAD-560V8LF (T2) or a Coilcraft
CR7983-CL (T3) 1CT:2CT turns ratio transformer; the default
is the Coilcraft transformer. The Halo Electronics footprint is in
the middle of the Coilcraft footprint. Figure 4 and Figure 6 show
the efficiency curves when the board operates in single-supply
configuration using a Coilcraft transformer (CR7983-CL) and a
Halo Electronics (TGRAD-560V8LF) transformer, respectively.
1000
Figure 3. Switching Frequency (fSW) vs. Oscillator Resistance (ROC)
OTHER INPUT AND ISOLATED OUTPUT SUPPLY
OPTIONS
In the single-supply configuration, the board can be set up to
have a 3.3 V secondary isolated supply with a 3.3 V or 5 V primary
input supply. Short-circuiting R10 by soldering a 0 Ω, 0603 resistor
to R9 sets the output supply to 3.3 V. The voltage at the feedback
node (the FB pin of the ADuM4070) should be the desired output
voltage divided to approximately 1.25 V. Having R10 open-circuited
sets the secondary isolated supply to 5 V, and having R10 shortcircuited sets the supply to 3.3 V. See the ADuM4070 data sheet
for more information about setting the secondary isolated output
supply voltage. Figure 7 shows how the efficiency curves change
in single-supply configuration when the board is reconfigured
by open- or short-circuiting R10.
Rev. 0 | Page 5 of 12
Evaluation Board User Guide
90
90
80
80
70
70
60
60
EFFICIENCY (%)
50
40
1MHz
700kHz
500kHz
200kHz
30
20
40
1MHz
700kHz
500kHz
200kHz
30
20
10
50
100
150
200
250
300
350
400
450
500
LOAD CURRENT (mA)
0
10663-004
0
0
80
80
70
70
60
60
EFFICIENCY (%)
90
50
40
–40°C
+25°C
+105°C
10
200
250
300
350
LOAD CURRENT (mA)
400
450
500
350
400
450
500
0
10663-005
150
300
30
10
100
250
5.0V IN TO 5.0V OUT
5.0V IN TO 3.3V OUT
3.3V IN TO 3.3V OUT
40
20
50
200
50
20
0
150
Figure 6. 5 V Input to 5 V Output Efficiency Using a 1CT: 2CT Halo Electronics
Transformer (TGRAD-560V8LF) at Various Switching Frequencies
90
0
100
LOAD CURRENT (mA)
Figure 4. 5 V Input to 5 V Output Efficiency Using a 1CT:2CT Coilcraft Transformer
(CR7983-CL) at Various Switching Frequencies
30
50
10663-006
10
0
EFFICIENCY (%)
50
0
50
100
150
200
250
300
350
LOAD CURRENT (mA)
Figure 5. 5 V Input to 5 V Output Efficiency Using a 1CT:2CT Coilcraft Transformer
(CR7983-CL) at 500 kHz Over Temperature
Rev. 0 | Page 6 of 12
400
450
500
10663-007
EFFICIENCY (%)
UG-403
Figure 7. Single-Supply Efficiency for Various Output Configurations
Using a 1CT:2CT Coilcraft Transformer (CR7983-CL) at 500 kHz
Evaluation Board User Guide
UG-403
DOUBLE SUPPLY
The ADuM4070 switching regulator on this evaluation board can
be configured for double-supply output (for more information
about the transformer, see the Transformer Selection section).
When the ADuM4070 is set to double-supply mode, the feedback
divider resistors should be configured as described in Table 1
and the output mode resistors should be configured as described
in Table 2.
By default, the double-supply configuration provides a regulated
15 V output and an unregulated 7.5 V output, which are isolated
from the 5 V primary input supply. The double supply is capable
of delivering up to 140 mA to external loads. The double supply
can be reconfigured as 12 V (regulated) and 6 V (unregulated)
secondary isolated supplies or as positive and negative supplies.
See the Other Secondary Isolated Supply Configurations section
for more information.
TERMINALS
In the double-supply configuration, the EVAL-ADuM4070EBZ
board has terminal blocks on Side 1 (the primary/power supply
input side) and Side 2 (the secondary/power supply output side).
An 8.0 mm isolation barrier separates Side 1 from Side 2. Table 5
summarizes the functions of the terminal connections. These
connections are described in detail in the Input Power Connections
and Output Power Connections sections.
Input Power Connections
Connect 5 V to P1 (labeled 5V), and connect the negative end
of the supply to P2 (labeled GND). These are the only off-board
connections required for the board to function in double-supply
configuration.
VDD1 is the ADuM4070 transformer driver supply, and VDDA is
the primary supply voltage (see the ADuM4070 data sheet for
additional information). VDD1 and VDDA are bypassed by a 47 µF
ceramic capacitor (C3) and a 0.1 µF local bypass capacitor (C8)
located close to the ADuM4070. R4, R3, C4, and C5 are provided
for an optional and unpopulated snubber, which can be used to
reduce radiated emissions.
Output Power Connections
Output loads can be connected to P9 (labeled OUT2) and P7
(labeled OUT1), which are the isolated, unregulated 7.5 V and
regulated 15 V output supplies, respectively. Connect the return
of the load to P10 and P8, which are labeled ISO_GND.
Side 2 is powered by the secondary isolated 15 V supply. The
ADuM4070 internal low dropout regulator converts this voltage
to 5 V. The regulated 5 V supply powers the ADuM4070 secondary
side. Therefore, the ADuM4070 VREG pin is 15 V, and the VDD2 pin
is 5 V. The 15 V supply connects to P7 (labeled OUT1). The
7.5 V supply connects to P9 (labeled OUT2). The Side 2 ground
reference is tied to P10. See the ADuM4070 data sheet for an
explanation of the double-supply theory of operation. Figure 8
through Figure 11 show efficiency curves for the double supply
with the 15 V or 12 V isolated output supply connected to VREG.
Powering VREG from the Unregulated 7.5 V Supply
VREG can be powered from the unregulated 7.5 V supply, which
results in higher efficiency. However, when the 15 V supply is
unloaded, the unregulated 7.5 V supply is approximately 3 V,
which is insufficient for powering the ADuM4070 secondary
side. This causes the double supply to run open-loop, leaving
the 15 V supply unregulated. Using 15 V for VREG ensures that
the secondary side of the ADuM4070 powers up under light
load conditions. Move the 0 Ω, 0603 resistor from R8 to R9 to
power Side 2 from the 7.5 V supply.
Care must be taken to avoid driving an output pin because this
can result in permanent damage to the ADuM4070.
Table 5. Double-Supply Terminal Function Descriptions
Terminal
P1
P2
P9
Label
5V
GND
OUT2
P10
P7
ISO_GND
OUT1
P8
ISO_GND
Description
Side 1—5 V primary input supply
Side 1—ground reference
Side 2—7.5 V secondary isolated supply
(unregulated)
Side 2—ground reference
Side 2—15 V secondary isolated supply
(regulated)
Side 2—ground reference
TRANSFORMER SELECTION
The EVAL-ADuM4070EBZ supports multiple transformer
options. In the double-supply configuration, the board must be
equipped with a Halo Electronics TGRAD-590V8LF (T2) or a
Coilcraft CR7984-CL (T3) 1CT:3CT turns ratio transformer
(see the ADuM4070 data sheet for details on transformer
selection with the ADuM4070). Figure 8 and Figure 10 show
the efficiency of the supply using a 1CT:3CT Coilcraft transformer
(CR7984-CL) and a 1CT:3CT Halo Electronics transformer
(TGRAD-590V8LF), respectively, at various switching frequencies.
Figure 9 shows how temperature affects efficiency.
SWITCHING FREQUENCY OPTIONS
The resistance connected from the ADuM4070 oscillator
control pin (OC) to ground sets the double-supply switching
frequency. Figure 3 shows the relationship between this
resistance and the converter switching frequency. The EVALADuM4070EBZ can be configured with 0 Ω, 0603 resistors to
set one of four preset switching frequencies. Table 6 lists the
switching frequencies that can be selected by short- or opencircuiting R12, R13, and R14.
The user can select a different switching frequency by removing
R12 and R13 and then choosing R18 based on Figure 3. The board
is configured for the 500 kHz setting by default. Figure 8 and
Figure 10 show how the switching frequency affects the efficiency
of the supply using a Coilcraft transformer (CR7984-CL) and a
Halo Electronics transformer (TGRAD-590V8LF), respectively.
Rev. 0 | Page 7 of 12
UG-403
Evaluation Board User Guide
Table 6. Switching Frequency Selection
80
R12
0Ω
Open
0Ω
0Ω
70
R14
Open
0Ω
0Ω
0Ω
ROC
300 kΩ
100 kΩ
75 kΩ
50 kΩ
Switching Frequency (fSW)
200 kHz
500 kHz (default)
700 kHz
1 MHz
60
EFFICIENCY (%)
R13
Open
Open
Open
0Ω
90
50
40
5V IN TO 12V OUT
5V IN TO 15V OUT
30
80
20
70
0
50
0
40
40
30
50
LOAD CURRENT (mA)
60
70
OTHER SECONDARY ISOLATED SUPPLY
CONFIGURATIONS
fSW = 1MHz
fSW = 700kHz
fSW = 500kHz
fSW = 200kHz
10
0
10
20
30
40
50
60
70
80
10461-011
0
90 100 110 120 130 140
LOAD CURRENT (mA)
Figure 8. 5 V Input to 15 V Output Efficiency Using a 1CT:3CT Coilcraft
Transformer (CR7984-CL) at Various Switching Frequencies
80
70
60
EFFICIENCY (%)
20
Figure 11. Double-Supply Efficiency for Various Output Configurations
Using a 1CT:5CT Coilcraft Transformer (CR7984-CL) at 500 kHz
30
20
50
40
–40°C
+25°C
+105°C
30
20
In the double-supply configuration, the EVAL-ADuM4070EBZ
board can be configured to have 12 V regulated and 6 V unregulated secondary isolated supplies by short-circuiting R11 with a
0 Ω resistor for R10. The regulated supply voltage is set by the
fraction of it that is fed back to the ADuM4070 via the voltage
divider comprising R6, R11, R15, and R10. The voltage at the
feedback pin (FB) is 1.25 V. With R10 open-circuited, the
ADuM4070 feedback voltage is approximately 1.25 V if VISO
is 15 V. When R10 is short-circuited, the feedback voltage is
approximately 1.25 V if VISO is 12 V (see the ADuM4070 data
sheet for more information about setting the secondary isolated
output supply voltage). Figure 11 shows the efficiency curves for
both output settings at 500 kHz using a Coilcraft transformer
(CR7984-CL).
Positive and Negative Outputs
0
0
10
20
30
40
50 60 70 80 90 100 110 120 130 140
LOAD CURRENT (mA)
10663-009
10
Figure 9. 5 V Input to 15 V Output Efficiency Using a 1CT:3CT Coilcraft
Transformer (CR7984-CL) at 500 kHz and Various Temperatures
90
80
70
EFFICIENCY (%)
10
10663-011
EFFICIENCY (%)
10
60
60
1MHz
700kHz
500kHz
200kHz
50
40
Although the +15 V output can be regulated, the same problems
with regulation can occur as described in the Powering VREG from
the Unregulated 7.5 V Supply section. In addition, the −15 V
supply can vary over a wide range because it is unregulated and
influenced by the changes that occur on the +15 V output.
30
20
0
10
20
30
40
50 60 70 80 90 100 110 120 130 140
LOAD CURRENT (mA)
10663-010
10
0
In the double-supply configuration, the EVAL-ADuM4070EBZ
board can be set up to have a positive and negative ±15 V supply by
changing the transformer to a turns ratio 1CT:5CT transformer
(see the ADuM4070 data sheet for more information about these
transformers). Other changes begin with removing the 0 Ω
resistors from R5 and R8 and inserting them into R7 and R9.
Short-circuiting R2 instead of R1 changes the unregulated 7.5 V
supply into a −15 V supply. Short-circuiting R5 instead of R7
connects the transformer center tap to the ground plane instead
of the node where L2 and C2 are connected. Note that the negative
supply is unregulated. The positive and negative supplies can be
set for ±12 V instead of ±15 V by short-circuiting R10.
Figure 10. 5 V Input to 15 V Output Efficiency Using a 1CT:3CT Halo Electronics
Transformer (TGRAD-590V8LF) at Various Switching Frequencies
Rev. 0 | Page 8 of 12
Evaluation Board User Guide
UG-403
10663-012
EVALUATION BOARD SCHEMATIC AND ARTWORK
Figure 12. Evaluation Board Schematic
10663-013
10663-014
EVALUATION BOARD LAYOUT
Figure 14. Bottom Layer: Ground Fill
Figure 13. Top Layer: Ground Fill
Rev. 0 | Page 9 of 12
UG-403
Evaluation Board User Guide
BILL OF MATERIALS
Table 7.
Qty
1
4
1
1
3
2
3
2
2
6
8
1
1
1
1
1
1
5
5
1
Reference Designator
U1
D1 to D4
T2 1
T31
C1, C2, C3
C4, C5
C6, C7, C8
L1, L2
L3, L4
R1, R7, R9, R11, R14, R19
R2, R3, R4, R5, R8, R10, R12, R13
R6
R16
R17
R18
R15
R11
P1, P3, P5, P7, P9
P2, P4, P6, P8, P10
Description
Isolated switching regulator with integrated feedback
Schottky barrier rectifier, 0.5 A, 40 V, SMD, SOD-123
Transformer, 1CT:2CT turns ratio, SMD (not populated)
Transformer, 1CT:2CT turns ratio, SMD
Capacitor, ceramic, X7R, SMD, 1210, 47 µF, 20%, 10 V
Capacitor, ceramic, SMD, 0603 (not populated)
Capacitor, ceramic, X7R, SMD, 0603, 0.1 µF
Inductor, SMD, 2424, 47 µH, 20%, 0.17 Ω (not populated)
Inductor, SMD, 1212, 47 µH, 20%, 1.25 Ω
Resistor chip, SMD, 0805, 0 Ω, 1/8 W
Not populated
Resistor chip, SMD, 0805, 17.4 kΩ, 1/8 W, 1%
Resistor chip, SMD, 0805, 300 kΩ, 1/8 W, 1%
Resistor chip, SMD, 0805, 150 kΩ, 1/8 W, 1%
Resistor chip, SMD, 0805, 100 kΩ, 1/8 W, 1%
Resistor chip, SMD, 0805, 10.5 kΩ, 1/8 W, 1%
Resistor chip, SMD, 0805, 14.3 kΩ, 1/8 W, 1%
Test point, red
Test point, black
Supplier/Part Number
Analog Devices, Inc./ADuM4070ARIZ
ON Semiconductor/MBR0540
Halo Electronics/TGRAD-560V6LF
Coilcraft/CR7983-CL
Murata/GRM32ER71A476KE15L
N/A
AVX/0603YC104KAT2A
Murata/LQH6PPN470M43
Murata/LQH3NPN470MM0
Panasonic/ECG/ERJ-6GEY0R00V
N/A
Panasonic/ECG/ERJ-6ENF1742V
Yageo/RC0805FR-07300KL
Yageo/RC0805FR-07150KL
Panasonic/ECG/ERJ-6ENF1003V
Panasonic/ECG/ERJ-6ENF1052V
Panasonic/ECG/ERJ-6ENF1432V
Components Corp./TP-104 series
Components Corp./TP-104 series
The board can be populated with either a Coilcraft transformer or a Halo Electronics transformer. Do not populate both T2 and T3.
Rev. 0 | Page 10 of 12
Evaluation Board User Guide
UG-403
NOTES
Rev. 0 | Page 11 of 12
UG-403
Evaluation Board User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG10663-0-3/13(0)
Rev. 0 | Page 12 of 12
工商网监
湘ICP备2023018690号
