EVAL-ADXL355-PMDZ

EVAL-ADXL354/EVAL-ADXL355 User Guide UG-1030 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluating the ADXL354/ADXL355 Low Noise, Low Drift, Low Power, 3-Axis MEMS Accelerometers FEATURES PRINTED CIRCUIT BOARD LAYOUT 2 sets of spaced vias for populating 6-pin headers Easily attachable to prototyping board or PCB Small size and board stiffness minimize impact on the system being monitored and acceleration measurements EQUIPMENT NEEDED External host processor DOCUMENTS NEEDED ADXL354/ADXL355 data sheet The EVAL-ADXL354BZ, EVAL-ADXL354CZ, and EVALADXL355Z are simple evaluation boards that allow quick evaluation of the performance of the ADXL354 and the ADXL355 low noise, low power, 3-axis, MEMS accelerometer. The EVALADXL354BZ is an analog output supporting a ±2 g or ±4 g accelerometer; the EVAL-ADXL354CZ is an analog output supporting a ±2 g or ±8 g accelerometer; and the EVAL-ADXL355Z is a digital output supporting ±2 g, ±4 g, or ±8 g. These evaluation boards are ideal for evaluating the ADXL354 and ADXL355 in an existing system because the stiffness and small size of the evaluation board minimizes the effect of the evaluation board on both the system and acceleration measurements. 14832-001 GENERAL DESCRIPTION Figure 1. EVAL-ADXL354BZ and EVAL-ADXL354CZ Evaluation Boards 14832-002 Full details about the ADXL354/ADXL355 are available in the ADXL354/ADXL355 data sheet, which is available from Analog Devices, Inc., and should be consulted in conjunction with this user guide when using this evaluation board. Figure 2. EVAL-ADXL355Z Evaluation Board PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. A | Page 1 of 5 UG-1030 EVAL-ADXL354/EVAL-ADXL355 User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Circuit Description............................................................................3 Equipment Needed ........................................................................... 1 Handling Considerations .................................................................3 Documents Needed .......................................................................... 1 Evaluation Board Schematics and Artwork ...................................4 General Description ......................................................................... 1 Ordering Information .......................................................................5 Printed Circuit Board Layout.......................................................... 1 Bill of Materials ..............................................................................5 Revision History ............................................................................... 2 Related Links ..................................................................................5 Evaluation Board Hardware ............................................................ 3 REVISION HISTORY 6/2018—Rev. 0 to Rev. A Changes to Figure 7 and Figure 8 ................................................... 4 9/2016—Revision 0: Initial Version Rev. A | Page 2 of 5 EVAL-ADXL354/EVAL-ADXL355 User Guide UG-1030 EVALUATION BOARD HARDWARE VDD VDDIO The EVAL-ADXL354BZ, EVAL-ADXL354CZ, and EVALADXL355Z evaluation boards allow users to access the individual connections of the ADXL354 and ADXL355. Each of the evaluation boards include decoupling capacitors for supplies, a few discrete resistors to provide isolation on the V1P8ANA and V1P8DIG pins, and two 6-pin headers. Refer to the ADXL354/ ADXL355 data sheet for more detail on specific pin definitions. The power supplies for the ADXL354/ADXL355 is decoupled using multiple 0.1 μF ceramic (0603) capacitors. P1 2 XOUT 3 4 YOUT 6 ZOUT 5 6 DRDY 202-187 14832-005 INT2 Figure 5. EVAL-ADXL355Z Function Block Diagram for Header P1 P2 V1P8ANA 1 2 V1P8DIG 3 4 SCLK/VSSIO MISO/SDA 5 6 CS/SCL MOSI/SDA 202-187 Figure 6. EVAL-ADXL355Z Function Block Diagram for Header P2 The vias or headers allow the evaluation boards to attach to either a prototyping breadboard or to a printed circuit board (PCB) in an existing user system. Four holes are provided in the corners of the evaluation board for mechanical attachment of the evaluation boards in many applications. An external host processor is required for communication to the ADXL355, while the analog output of the ADXL354 must be connected to a band limited analog-to-digital converter (ADC). 202-187 CIRCUIT DESCRIPTION 14832-003 1 Figure 3. EVAL-ADXL354BZ and EVAL-ADXL354CZ Function Block Diagram for Header P1 P2 1 2 ST1 V1P8DIG 3 4 ST1 TEMP 5 6 The PCB layout of the EVAL-ADXL354BZ, EVAL-ADXL354CZ, and EVAL-ADXL355Z evaluation boards are shown in Figure 2. The ADXL354 and ADXL355 each have two moded by which they can be powered: by integrated low dropout regulators (LDOs) or external, user supplied 1.8 V regulated supplies. Refer to the ADXL354/ADXL355 data sheet for more information. HANDLING CONSIDERATIONS 14832-004 V1P8ANA 202-187 INT1 4 The dimensions of the evaluation boards are 0.8 in × 0.8 in. VDD VDDIO 5 2 3 14832-006 The EVAL-ADXL354BZ and EVAL-ADXL354CZ evaluation boards have capacitors on each axis output to set the output low-pass filter and two 3-position jumpers to configure Range and Mode. The two 6-pin headers provide access to all other pins. Header P1 provides access to VDDIO (sets the RANGE pin and the STBY pin levels on the EVAL-ADXL354BZ and EVALADXL354CZ evaluation boards), VDD (supplies the ADXL354 VSUPPLY pin), VSS/VSSIO (supplies the ground connection), XOUT, YOUT, and ZOUT, shown in Figure 3. Header P2 provides access to V1P8ANA, V1P8DIG, TEMP, ST1, ST2, and VSS (supplies the ground connection), shown in Figure 4. P1 1 Figure 4. EVAL-ADXL354BZ and EVAL-ADXL354CZ Function Block Diagram for Header P2 The EVAL-ADXL355Z uses two 6-pin headers to provide access to all pins. Header P1 provides access to VDDIO, VDD (which is connected to the ADXL355 VSUPPLY pin), VSS/VSSIO (supply ground connection), INT1, INT2, and DRDY, shown in Figure 5. Header P2 provides access to V1P8ANA, V1P8DIG, MISO/ASEL, CS/SCL, SCLK/VSSIO, and MOSI/SDA (see Figure 6). The EVAL-ADXL354BZ, EVAL-ADXL354CZ, and EVALADXL355Z evaluation boards are not reverse polarity protected. Reversing any of the supply connections, including the VSS and VSSIO pins, can cause damage to the ADXL354/ADXL355. Dropping the evaluation boards on a hard surface can generate several thousand g of acceleration, which can exceed the ADXL354/ADXL355 data sheet absolute maximum limits. Rev. A | Page 3 of 5 UG-1030 EVAL-ADXL354/EVAL-ADXL355 User Guide EVALUATION BOARD SCHEMATICS AND ARTWORK VDD VDDIO P1 VDD C3 0.1µF ZOUT VDDIO RANGE 1 2 1 3 2 3 RANGE 11 C4 0.1µF V1P8ANA U1 ADXL354 ST1 VSS ST2 V1P8DIG VDDIO TEMP 202-072 YOUT 14 202-187 C2 0.1µF 5 4 R1 1kΩ 10 9 R2 1kΩ 8 209-381 2 ST1 V1P8DIG 3 4 ST2 TEMP 5 6 C9 0.1µF 202-187 VDDIO MODE 1 2 C10 0.1µF C11 0.1µF 202-073 H4 14832-007 H3 C8 0.1µF P2 V1P8ANA 1 3 MOUNTING HOLES H2 C7 0.1µF C6 0.1µF VDDIO H1 C5 0.1µF VSUPPLY C1 0.1µF STBY ZOUT 7 6 12 5 XOUT YOUT VSSIO XOUT 4 13 2 3 6 1 Figure 7. EVAL-ADXL354BZ and EVAL-ADXL354CZ Schematic VDD VDDIO P1 VDD 11 V1P8ANA U1 VSS RESERVED MOSI/SDA ADXL355 7 SCLK/VSSIO 4 3 VDDIO H3 V1P8DIG R1 1kΩ 10 9 R2 1kΩ 8 C6 0.1µF 209-358 C7 0.1µF C8 0.1µF C9 0.1µF P2 V 1P8ANA 1 2 CS/SCL V 1P8DIG 3 4 SCLK/VSSIO 6 MOSI/SDA MISO/SDA 5 202-187 VDDIO STBY 1 2 C10 0.1µF H4 C11 0.1µF 202-073 14832-008 H2 C5 0.1µF 3 MOUNTING HOLES H1 C4 0.1µF VSUPPLY DRDY 2 CS/SCL MISO/ASEL 1 12 C3 0.1µF 14 202-187 C2 0.1µF INT1 C1 0.1µF VSSIO DRDY 6 6 13 INT2 5 INT2 INT1 4 VDDIO 2 3 5 1 Figure 8. EVAL-ADXL355Z Schematic Rev. A | Page 4 of 5 EVAL-ADXL354/EVAL-ADXL355 User Guide UG-1030 ORDERING INFORMATION BILL OF MATERIALS Table 1. EVAL-ADXL354BZ and EVAL-ADXL354CZ Evaluation Boards Qty 1 11 2 2 2 Reference Designator U1 C1 to C11 R1, R2 MODE, RANGE P1, P2 1 PCB Description High performance, 3-axis MEMS accelerometer, LC-14 Capacitors, ceramic, 0.1 μF, 50 V, 10%, X7R, 0603 Resistors, 100 kΩ, 1/10W, 1%, 0603 Jumpers, 3-position, through hole Headers, male, nonshrouded, 2 × 3, 0.1" spacing, through hole, do not insert ADXL354 bare board Manufacturer Analog Devices, Inc. Cal-Chip Cal-Chip Prolex FCI Part Number ADXL354 GMC10X7R104K50NTLF CR0603F1001T1LF 2556P03UA00 67996-206HLF Analog Devices, Inc. EVAL-ADXL354BZ or EVAL-ADXL354CZ Table 2. EVAL-ADXL355Z Evaluation Board Qty 1 8 2 1 2 Reference Designator U1 C4 to C11 R1, R2 STBY P1, P2 1 PCB Description High performance, 3-axis MEMS accelerometer, LC-14 Capacitors, ceramic, 0.1 μF, 50 V, 10%, X7R, 0603 Resistors, 100 kΩ, 1/10W, 1%, 0603 Jumpers, 3-position, through hole Headers, male, nonshrouded, 2 × 3, 0.1" spacing, through hole, do not insert ADXL355 bare board Manufacturer Analog Devices, Inc. Cal-Chip Cal-Chip Prolex FCI Part Number ADXL355 GMC10X7R104K50NTLF CR0603F1001T1LF 2556P03UA00 67996-206HLF Analog Devices, Inc. EVAL-ADXL355Z RELATED LINKS Resource ADXL354/ADXL355 Description ADXL354/ADXL355 product page ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2016–2018 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG14832-0-6/18(A) Rev. A | Page 5 of 5