EVAL-FDA-2CPZ-24

EVAL-FDA-2CPZ-24 User Guide UG-018 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluation Board for Dual High Speed Differential Amplifiers Figure 1 shows the component side and circuit side of the evaluation board. Figure 2 shows the evaluation board schematic. FEATURES Enables quick breadboarding/prototyping User defined circuit configuration Edge mounted SMA connector provisions Easy connection to test equipment and other circuits Two independent circuits enhance flexibility The 4-layer evaluation board accepts edge mounted subminiture version A (SMA) connectors on both inputs and outputs, which allows efficient and quick connection to test equipment or other circuitry. GENERAL DESCRIPTION The EVAL-FDA-2CPZ-24 is designed to aid in the evaluation of dual high speed differential amplifiers. The EVAL-FDA-2CPZ-24 is a bare board (that is, there are no components soldered to the evaluation board) that enables users to quickly prototype a variety of differential amplifier circuits, which minimizes risk and reduces time to market. The EVAL-FDA-2CPZ-24 evaluation board supports any of the Analog Devices, Inc., dual high speed differential amplifiers in 4 mm × 4 mm, lead frame chip scale packages (LFCSP). The evaluation board ground plane, component placement, and power supply bypassing are optimized for maximum circuit flexibility and performance. The evaluation board uses a variety of surface-mount technology (SMT) component case sizes: 0402, 0508, and 7343. Figure 3 and Figure 5 show the evaluation board assembly drawings. Figure 4 and Figure 6 show the metal layout pattern for connecting the board to the operational amplifier and to the supporting circuitry. 08142-006 DIGITAL PICTURE OF THE EVALUATION BOARD CIRCUIT SIDE COMPONENT SIDE NOTES 1. THE EVALUATION BOARD SILKSCREEN PART NUMBER LABELING ON YOUR BOARD MAY BE DIFFERENT FROM WHAT IS SHOWN HERE. Figure 1. Component and Circuit Side of PCB PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. C | Page 1 of 5 UG-018 EVAL-FDA-2CPZ-24 User Guide TABLE OF CONTENTS Features .............................................................................................. 1  Evaluation Board Schematic and Artwork.....................................3  General Description ......................................................................... 1  Ordering Information .......................................................................5  Digital Picture of the Evaluation Board ......................................... 1  Bill of Materials ..............................................................................5  Revision History ............................................................................... 2  REVISION HISTORY 8/2016—Rev. B to Rev. C Changed EB-D24CP44-2Z to EVAL-FDA-2CPZ-24 ..... Throughout Changes to Table 1 ............................................................................. 5 1/2015—Rev. A to Rev. B Changes to General Description Section ...................................... 1 Added Ordering Information Section and Table 1 ...................... 5 2/2010—Rev. 0 to Rev. A Changes to General Description and Figure 1 ............................. 1 7/2009—Revision 0: Initial Version Rev. C | Page 2 of 5 3 P2 Figure 2. Dual Differential Amplifier Universal Evaluation Board Schematic GND2 SMA AGND SMA SMA AGND –VS1 SMA GND4 –IN2 +IN2 –IN1 +IN1 R14* GND3 0.1µF C2 PD1 *USER-DEFINED VALUE DNI = DO NOT INSTALL AGND GND1 AGND 10µF + C1 +VS1 (TP2) 2 P2 +VS1 –IN2 AGND +IN2 AGND –IN1 +IN1 R6* R5* –VS1 R8* R7* +VS1 R4* R3* R2* R1* 0Ω R28 0Ω R26 0Ω R25 0Ω R27 R10* R9* +VS1 +VS1 +FB1 –IN1 6 –VS2 +VS2 23 200 + 22 9 +VS2 (TP3) 10µF + C7 AGND R12* 8 7 +IN2 5 –FB2 4 3 2 1 24 R11* AGND C4 10µF –VS1 +VS2 R13* 21 10 Z1 0.1µF C6 –OUT2 VOCM2 (TP6) AGND 12 PD2 –VS2 –VS2 VOCM1 +OUT1 AGND C10 19 0.1µF 11 R30 DNI 0.1µF C9 20 AGND –VS1 +VS2 1 –OUT1 P2 PD1/DIS1 VOCM2 –VS1 (TP5) 13 14 15 16 17 18 SMA AGND R29 C12 VOCM1 TP1 R19* R18* AGND AGND SMA 0.1µF DNI VOCM2 VOCM1 R17* R16* AGND R24 DNI +OUT2 AGND R23 DNI –OUT2 AGND R22 DNI +OT1 AGND R21 DNI –OUT1 SMA SMA SMA SMA SMA PD2/DIS2 +OUT2 –OUT2 2 3 P3 P3 C13 1 AGND AGND 10µF + C14 –VS2 (TP4) 3 2 1 P3 0.1µF +OUT1 –OUT1 P1 P1 P1 +VS1 PD2 R15* R20* –VS1 AGND –VS2 +VS2 08142-001 SMA +IN1 –IN2 –FB1 +FB2 Rev. C | Page 3 of 5 +OUT2 PD1/DIS1 EVAL-FDA-2CPZ-24 User Guide UG-018 EVALUATION BOARD SCHEMATIC AND ARTWORK EVAL-FDA-2CPZ-24 User Guide 08142-002 08142-003 UG-018 Figure 5. Board Assembly Drawing, Circuit Side 08142-004 08142-005 Figure 3. Board Assembly Drawing, Component Side Figure 4. Board Layout Pattern, Component Side Figure 6. Board Layout Pattern, Circuit Side Rev. C | Page 4 of 5 EVAL-FDA-2CPZ-24 User Guide UG-018 ORDERING INFORMATION BILL OF MATERIALS Table 1. Qty 10 26 4 4 4 Reference Designator GND1 to GND4, TP1 to TP6 R1 to R24, R29 to R30 R25 to R28 C1, C4, C7, C14 C2, C6, C9, C13 Description Test points Resistors, user defined Resistors, 0 Ω Capacitors, tantalum, 10 μF Capacitors, 0.1 μF Package Part Number 0402 0603 7343 0508 or 0603 2 12 C10, C12 +IN1, −IN1, +IN2, −IN2, VOCM1, VOCM2, PD1/DIS1, PD2/DIS2, +OUT1, −OUT1, +OUT2, −OUT2 P1 to P3 Z1 Capacitors, 0.1 μF SMA connectors 0402 End launch PXXXKLCT-ND P0.0GCT-ND 399-3765-1-ND 478-7414-1-ND or 399-1095-1-ND 399-3027-1-ND J502-ND 3-pin headers, 100 mils spacing Dual differential amplifier TSW-103-08-G-S 24-lead LFCSP 3 1 SAM1038-03-ND ADA4927-2, ADA4930-2, ADA4937-2, ADA4938-2, ADA4939-2, or ADA4940-2 ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2009–2017 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG08142-0-8/17(C) Rev. C | Page 5 of 5