Evaluation Board User Guide
UG-543
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Boards for Full-Duplex and Half-Duplex RS-485 Transceivers
in 8-Lead/14-Lead SOIC Packages
EVAL-RS485HDEBZ
Easy evaluation of half- and full-duplex RS-485 transceivers
Board layouts for standard RS-485 SOIC footprints
8-lead, SOIC, half-duplex RS-485 (EVAL-RS485HDEBZ)
8-lead, SOIC, full-duplex RS-485 (EVAL-RS485FD8EBZ)
14-lead, SOIC, full-duplex RS-485 (EVAL-RS485FDEBZ)
Power/ground connections through screw terminal blocks
Screw terminal blocks for logic I/O and RS-485 signals
Jumper selectable enable/disable for RE and DE
Test points for measuring all signals
Resistors and footprints for termination and biasing
networks
11390-001
FEATURES
Figure 1.
EVAL-RS485FD8EBZ
APPLICATIONS
Full- and half-duplex RS-485 transceiver evaluation
EVALUATION KIT CONTENTS
11390-002
1 EVAL-RS485HDEBZ or
1 EVAL-RS485FD8EBZ or
1 EVAL-RS485FDEBZ
(Main device available separately when ordering)
GENERAL DESCRIPTION
The EVAL-RS485HDEBZ, EVAL-RS485FD8EBZ, and
EVAL-RS485FDEBZ allow quick and easy evaluation of RS-485
transceivers with standard SOIC footprints. The evaluation
board allows all of the input and output functions to be
exercised without the need for external components. Screw
terminal blocks provide convenient connections for power and
ground, digital I/O, and RS-485 signals.
Figure 2.
EVAL-RS485FDEBZ
11390-003
The EVAL-RS485HDEBZ evaluation board has a footprint for
a half-duplex RS-485 transceiver in an 8-lead SOIC package.
The EVAL-RS485FD8EBZ evaluation board has a footprint for
a full-duplex RS-485 transceiver in an 8-lead SOIC package.
The EVAL-RS485FDEBZ evaluation board has a footprint for a
full-duplex RS-485 transceiver in a 14-lead SOIC package.
Figure 3.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. A | Page 1 of 16
UG-543
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Other Board Components............................................................4
Applications ....................................................................................... 1
Evaluation with Applications .......................................................4
Evaluation Kit Contents ................................................................... 1
Evaluation Board Schematics and Layouts ....................................7
General Description ......................................................................... 1
EVAL-RS485HDEBZ ....................................................................7
EVAL-RS485HDEBZ ....................................................................... 1
EVAL-RS485FD8EBZ ...................................................................9
EVAL-RS485FD8EBZ ...................................................................... 1
EVAL-RS485FDEBZ .................................................................. 11
EVAL-RS485FDEBZ......................................................................... 1
Ordering Information .................................................................... 13
Revision History ............................................................................... 2
EVAL-RS485HDEBZ Bill of Materials .................................... 13
Evaluation Board Configuration .................................................... 3
EVAL-RS485FD8EBZ Bill of Materials ................................... 14
Setting Up the Evaluation Board ................................................ 3
EVAL-RS485FDEBZ Bill of Materials ..................................... 15
Input/Output Connections ......................................................... 3
Related Links ............................................................................... 16
REVISION HISTORY
3/2019—Rev. 0 to Rev. A
Changes to Table 1 ............................................................................ 3
Changes to Table 4 .......................................................................... 13
Changes to Table 6 .......................................................................... 14
Changes to Table 8 .......................................................................... 15
4/2013—Revision 0: Initial Version
Rev. A | Page 2 of 16
Evaluation Board User Guide
UG-543
EVALUATION BOARD CONFIGURATION
SETTING UP THE EVALUATION BOARD
INPUT/OUTPUT CONNECTIONS
In order to allow evaluation of any one of over 40 RS-485
transceivers, the evaluation boards are supplied with an
unpopulated footprint for the RS-485 transceiver. The
evaluation board allows all of the input and output functions
to be exercised without the need for additional external
components. Jumper configurations are shown in Table 2.
Digital I/O is connected via a screw terminal block on the left
of the board, allowing wire connections to equipment or a
UART. All boards include connections for data input (DI) and
receiver output (RO). The half-duplex and 14-lead SOIC fullduplex evaluation boards also have connections for receiver
enable (RE) and driver enable (DE). Alternatively, these inputs
can be driven by jumper connections to VCC and GND and/or
connected together (see Table 2).
To use the EVAL-RS485HDEBZ, fit an 8-lead SOIC half-duplex
transceiver to the footprint in the center of the board. For the
EVAL-RS485FD8EBZ, fit an 8-lead SOIC full-duplex transceiver to the footprint, and for the EVAL-RS485FDEBZ, a
14-lead SOIC full-duplex transceiver. Refer to Table 1 for a list
of parts available for each board.
The board is powered by connecting a 3.3 V or 5 V power
supply (refer to Table 1) to the screw terminals for VCC and
GND at the top of the evaluation board. A 22 µF or 10 µF
decoupling capacitor, C1, is fitted at the connector between
VCC and GND. The VCC pin of the RS-485 transceiver is fitted
with a decoupling capacitor of 100 nF, with a second footprint
for an optional additional capacitor.
Correspondingly labeled test points allow monitoring of the
power supply to the board and probe reference to ground.
Connections to an RS-485 bus are made via a screw terminal
block on the right of the board. For the half-duplex board, there
are two bus I/O signals, A and B, for noninverting and inverting
signals, respectively. For full-duplex boards, there are two input
bus signals, A and B, for noninverting and inverting signals,
respectively, and two corresponding output signals, Y and Z.
The bus cable may also include a common ground connection
or shield. These may also be connected to the screw terminal
block on the right of the board.
Test points are available on the board and appropriately labeled
for all digital and bus I/O signals.
Table 1. RS-485 Device and Board Cross Reference
Power Supply
Enhanced ESD, 3.3 V Supply
Enhanced ESD, 5 V Supply
Enhanced ESD, 3.3 V to 5 V
Supply
Half Duplex, 8-Lead EVAL-RS485HDEBZ
ADM3072E
ADM3075E
ADM3078E
ADM3483E
ADM3485E
ADM3486E
LTC2850
ADM483E
ADM485E
ADM487E
ADM1487E
LT1785
LT1785A
LTC1481
LTC1482
LTC1483
LTC1484
LTC1485
LTC1487
ADM3061E
LTC2862-1
LTC2862A-1
ADM3065E
LTC2862-2
LTC2862A-2
Rev. A | Page 3 of 16
Full-Duplex, 8-Lead
EVAL-RS485FD8EBZ
ADM3071E
ADM3074E
ADM3077E
ADM3488E
ADM3490E
LTC2851
Full-Duplex, 14-Lead
EVAL-RS485FDEBZ
ADM3070E
ADM3073E
ADM3076E
ADM3491E
LTC2852
ADM1490E
LTC1690
ADM1491E
LT1791
LT1791A
LTC2863-1
LTC2863-2
LTC2864-1
LTC2864-2
UG-543
Evaluation Board User Guide
Power Supply
Standard, 3.3 V Supply
Standard, 5 V Supply
Half Duplex, 8-Lead EVAL-RS485HDEBZ
ADM3483
ADM3485
ADM3493
ADM1485
ADM1486
ADM4850
ADM4851
ADM4852
ADM4853
ADM483
ADM485
LTC1480
LTC1685
LTC485
Full-Duplex, 8-Lead
EVAL-RS485FD8EBZ
ADM3488
ADM3490
Full-Duplex, 14-Lead
EVAL-RS485FDEBZ
ADM3491
ADM488
ADM488A
ADM4854
ADM4855
ADM4856
ADM4857
LTC1686
LTC490
ADM489
ADM489A
LTC1687
LTC491
Table 2. Jumper Configuration
Purpose
Select RE Input
Half-Duplex
Board
LK1
Full-Duplex
(8-Lead) Board
N/A
Full-Duplex
(14-Lead) Board
LK2
Select DE Input
LK2
N/A
LK3
Connect RT1
LK3
N/A
N/A
Connect RT2
LK4
N/A
N/A
Connect A to Y
N/A
LK1
LK5
Connect B to Z
N/A
LK2
LK6
OTHER BOARD COMPONENTS
All three boards include footprints for termination resistors
(RT1 and/or RT2) as well as pull-up and pull-down resistors.
Termination resistors of 120 Ω are fitted to the board; these may
be removed or replaced with a different value resistor as needed.
Full-duplex boards can be evaluated with A connected to Y and
B connected to Z (see Table 2). In this configuration, the two
termination resistors are in parallel, so the driver can be
evaluated with a load equivalent to a bus terminated at both ends.
For the half-duplex board, the same effect is achieved by
connecting in two parallel termination resistors using jumpers
on the board. Refer to Table 2 for jumper connections.
Biasing Resistors for Bus-Idle Failsafe
Pull-up and pull-down resistors are not fitted by default, but
may be required to provide an external biasing network for an
idle bus failsafe. These resistors are usually only connected at
one position on the bus and selected to provide a minimum
Connection
A
B
C
D
Description
Connects RE to VCC (disables receiver output).
Connects RE to GND (enables receiver output).
Allows RE input from screw terminal block.
Connects RE to DE input source.
A
B
C
Closed
Open
Closed
Open
Closed
Open
Closed
Open
Connects DE to VCC (enables driver outputs).
Connects DE to GND (disables driver outputs).
Allows DE input from screw terminal block.
RT1 is connected across A and B.
RT1 is disconnected.
RT2 is connected across A and B.
RT2 is disconnected.
A is connected to Y.
A is not connected to Y.
B is connected to Z.
B is not connected to Z.
differential input voltage (VID) between A and B of 200 mV.
Different resistor values are required depending on whether
a 3.3 V or 5 V supply is used, and how much noise margin is
required (that is, VID > 200 mV). ADM3070E to ADM3078E
and ADM4850 to ADM4857 have built-in failsafe for the bus
idle condition. For guidelines, refer to AN-960 Application
Note, RS-485/RS-422 Circuit Implementation Guide.
EVALUATION WITH APPLICATIONS
Full-Duplex RS-485 Transceiver Loopback
For full-duplex transceivers using the EVAL-RS485FDEBZ or
EVAL-RS485FD8EBZ boards, a loopback test can be set up by
closing LK5 and LK6 or LK1 and LK2, respectively. This test
is shown in Figure 4.
A signal generator is connected to DI and this allows
verification of the bus signals and the receiver output. Note
the jumper positions of LK3 (A) and LK2 (B) for the EVALRS485FDEBZ board. In this configuration, the default
Rev. A | Page 4 of 16
Evaluation Board User Guide
UG-543
Connecting to an Existing RS-485 Network
termination resistors can be used since both 120 Ω resistors
on the board will be connected in parallel by the loop-back,
ensuring the test is conducted with a standard RS-485 load of
60 Ω (bus terminated at both ends by 120 Ω).
For a two-wire connection to an existing RS-485 network,
driver enable (DE) should be disabled (LK2 for EVALRS485HDEBZ, LK3 for EVAL-RS485FDEBZ) by moving to
Position B, or else should be controlled externally (Position C)
based on received data.
Half-Duplex RS-485 Transceivers Point-to-Point Test
With two boards, a point-to-point test can be set up. Two halfduplex boards are shown in this configuration in Figure 5.
Note the positions of LK1 and LK2 on each board to enable
the driver on one board and the receiver on the other board.
For EVAL-RS485FDEBZ, these correspond to LK2 and LK3,
although in this case, both boards can have the driver and
receiver enabled if LK5 and LK6 are open and a four-wire
connection is used. For EVAL-RS485FD8EBZ boards, LK1 and
LK2 must be open with a four-wire connection for the point-topoint link.
For a four-wire connection using EVAL-RS485FDEBZ, the
driver can be permanently enabled by placing LK3 in Position A,
if the Y and Z connections are connected only to RS-485
receivers. Otherwise, LK3 should be in Position B or Position C.
For a four-wire connection using EVAL-RS485FD8EBZ, the Y
and Z connections should only be connected to other RS-485
receiver inputs, as shown in Figure 6 for a multinode bus.
These full-duplex parts without driver or receiver enable inputs
can also typically be used in point-to-point four-wire RS-485
bus connections.
LK4 has been removed on each EVAL-RS485HDEBZ board in
order to ensure both ends of the bus have only a 120 Ω load.
For full-duplex boards with a four-wire connection, the correct
termination is on each end of the bus. If EVAL-RS485FDEBZ
boards are used with a two-wire connection and LK5 and LK6
are closed, then one termination resistor needs to be removed
from each board.
SIGNAL
GENERATOR
3.3V OR 5V
SUPPLY
OSCILLOSCOPE
J1
A
B
C
D
A
B
C
RE
DE
DI
A
RE
B
DE
Z
Y
DI
A
B
Z
Y
SHIELD
GND
11390-004
LK3
RO
LK5
LK2
LK6
J2
J3
VCC
GND
RO
EVAL-RS485FDEBZ
Figure 4. Full-Duplex RS-485 Transceiver Loop Back Test
Rev. A | Page 5 of 16
UG-543
Evaluation Board User Guide
3.3V OR 5V
SUPPLY
SIGNAL
GENERATOR
EVAL-RS485HDEBZ
J1
GND
RE
DE
DI
A
B
C
D
A
B
C
RO
RE
DE
DI
B
A
DE
A
DI
SHIELD
GND
LK2
OSCILLOSCOPE
VCC
LK3
LK4
LK1
J5
B
RE
EVAL-RS485HDEBZ
J1
GND
J3
RO
A
B
C
D
A
B
C
RO
3.3V OR 5V
SUPPLY
VCC
LK1
LK3
LK4
J3
RO
RE
DE
J5
B
B
A
A
DI
SHIELD
GND
11390-005
LK2
Figure 5. Half-Duplex RS-485 Two Board Point-to-Point Test
3.3V OR 5V
SUPPLY
UART Rx
MICROCONTROLLER/
PROCESSOR
UART Tx
RO
GND
J2
DI
VCC
A
RO
B
DI
Z
Y
EVAL-RS485FD8EBZ
J3
RT1
RT2 LK2 LK1
J1
MASTER NODE
A
B
Z
Y
SHIELD
GND
RT
RT
RT
RT
A
B
Z
Y
NODE 1
SLAVE
A
B
Z
Y
SLAVE
NODE 2
A
B
Z
Y
SLAVE
NODE N
11390-006
NOTES
1.REMOVE 50Ω TERMINATION RESISTORS FROM EVALUATION BOARD
2.MAXIMUM NUMBER OF NODES: 32.
3.RT IS EQUAL TO THE CHARACTERISTIC IMPEDANCE OF THE CABLE USED.
Figure 6. Full-Duplex (8-Lead SOIC) RS-485 Board Connected to Bus and Control Board
Rev. A | Page 6 of 16
Evaluation Board User Guide
UG-543
EVALUATION BOARD SCHEMATICS AND LAYOUTS
EVAL-RS485HDEBZ
11390-007
Figure 7. EVAL-RS485HDEBZ Schematic
Rev. A | Page 7 of 16
Evaluation Board User Guide
11390-008
UG-543
11390-009
Figure 8. EVAL-RS485HDEBZ Silkscreen
11390-010
Figure 9. EVAL-RS485HDEBZ Component Side
Figure 10. EVAL-RS485HDEBZ Solder Side
Rev. A | Page 8 of 16
Evaluation Board User Guide
UG-543
EVAL-RS485FD8EBZ
11390-011
Figure 11. EVAL-RS485FD8EBZ Schematic
Rev. A | Page 9 of 16
Evaluation Board User Guide
11390-012
UG-543
11390-013
Figure 12. EVAL-RS485FD8EBZ Silkscreen
11390-014
Figure 13. EVAL-RS485FD8EBZ Component Side
Figure 14. EVAL-RS485FD8EBZ Solder Side
Rev. A | Page 10 of 16
Evaluation Board User Guide
UG-543
EVAL-RS485FDEBZ
11390-015
Figure 15. EVAL-RS485FDEBZ Schematic
Rev. A | Page 11 of 16
Evaluation Board User Guide
11390-016
UG-543
11390-017
Figure 16. EVAL-RS485FDEBZ Silkscreen
11390-018
Figure 17. EVAL-RS485FDEBZ Component Side
Figure 18. EVAL-RS485FDEBZ Solder Side
Rev. A | Page 12 of 16
Evaluation Board User Guide
UG-543
ORDERING INFORMATION
EVAL-RS485HDEBZ BILL OF MATERIALS
Table 3.
Quantity
1
2
1
6
1
1
2
1
1
2
2
1
2
1
1
Reference Designator
C1
C2, C4
C3
A, B, DE, DI, RE, RO
GND
J1
J3, J5
LK1
LK2
LK3, LK4
R1, R2
R3
RT1, RT2
U1
VCC
Description
Capacitor, 100 nF, 0805
Not placed/optional
Capacitor, 10 µF, Case B
Test point, yellow
Test point, black
2-way terminal block
4-way terminal block
8-pin (4 × 2) 0.1" header and shorting block
6-pin (3 × 2) 0.1" header and shorting block
Jumper Block, 2 pin, 0.1" spacing
Not placed/optional
Resistor, 0 Ω, 0805
Resistor, 120 Ω, 0805
8-lead SOIC (not placed)
Test point, red
Supplier/Part Number
Multicomp/MCCA000274
Not applicable
Kemet/B45196H3106K209
Vero Technologies/20-313140
Vero Technologies/20-2137
Lumberg/KRM 02
Lumberg/KRM 04
Harwin/M20-9953646 and Harwin/M7566-05
Harwin/M20-9953646 and Harwin/M7566-05
Harwin/M20-9990246 and Harwin/M7566-05
Not applicable
Vishay Draloric/CRCW08050000Z0EA
Multicomp/MC 0.1W 0805 1% 120R
Analog Devices, Inc./see Table 4
Vero Technologies/20-313137
Table 4. EVAL-RS485HDEBZ Options for U1(Half-Duplex RS-485 Transceivers)
Enhanced ESD,
3.3 V Supply
ADM3072E
ADM3075E
ADM3078E
LTC2850
ADM3483E
ADM3485E
ADM3486E
Enhanced ESD,
5 V Supply
ADM483E
ADM485E
ADM487E
ADM1487E
LT1785
LT1785A
LTC1481
LTC1482
LTC1483
LTC1484
LTC1485
LTC1487
Enhanced ESD,
3.3 V to 5 V Supply
ADM3061E
ADM3065E
LTC2862-1
LTC2862-2
LTC2862A-1
LTC2862A-2
Standard,
3.3 V Supply
ADM3483
ADM3485
ADM3493
Standard,
5 V Supply
ADM1485
ADM1486
ADM483
ADM485
LTC1480
LTC1685
ADM4850
ADM4851
ADM4852
ADM4853
LTC485
Select the appropriate U1 devices in addition to EVAL-RS485HDEBZ when ordering. Ensure that the device ordered includes an R in the
part number for SOIC devices, for example, ADM3072EARZ.
Rev. A | Page 13 of 16
UG-543
Evaluation Board User Guide
EVAL-RS485FD8EBZ BILL OF MATERIALS
Table 5.
Quantity
1
2
1
6
1
2
1
2
2
1
2
1
1
Reference Designator
C1
C2, C4
C3
A, B, DI, RO, Y, Z
GND
J1, J2
J3
LK1, LK2
R1, R2
R3
RT1, RT2
U1
VCC
Description
Capacitor, 100 nF, 0805
Not placed/optional
Capacitor, 22 µF, Case C
Test point, yellow
Test point, black
2-way terminal block
6-way terminal block
Jumper Block, 2 pin, 0.1" spacing
Not placed/optional
Resistor, 0 Ω, 0805
Resistor, 120 Ω, 0805
8-lead SOIC (not placed)
Test point, red
Supplier/Part Number
Multicomp/MCCA000274
Not applicable
AVX/TAJC226K016RNJ
Vero Technologies/20-313140
Vero Technologies/20-2137
Lumberg/KRM 02
Lumberg/KRM 06
Harwin/M20-9990246 and Harwin/M7566-05
Not applicable
Vishay Draloric/CRCW08050000Z0EA
Multicomp/MC 0.1W 0805 1% 120R
Analog Devices/see Table 6
Vero Technologies/20-313137
Table 6. EVAL-RS485FD8EBZ Options for U1(Full-Duplex RS-485 Transceivers, 8-Lead SOIC)
Enhanced ESD,
3.3 V Supply
ADM3071E
ADM3074E
ADM3077E
ADM3488E
ADM3490E
LTC2851
Enhanced ESD,
5 V Supply
ADM1490E
LTC1690
Enhanced ESD,
3.3 V to 5 V Supply
LTC2863-1
LTC2863-2
Standard,
3.3 V Supply
ADM3488
ADM3490
Standard,
5 V Supply
ADM4854
ADM4855
ADM4856
LTC1686
ADM4857
ADM488
ADM488A
LTC490
Select the appropriate U1 devices in addition to EVAL-RS485FD8EBZ when ordering. Ensure that the device ordered includes an R in the
part number for SOIC devices, for example, ADM3071EARZ.
Rev. A | Page 14 of 16
Evaluation Board User Guide
UG-543
EVAL-RS485FDEBZ BILL OF MATERIALS
Table 7.
Quantity
1
1
2
6
1
1
1
1
1
1
2
2
1
2
1
1
Reference Designator
C1
C2
C3, C4
A, B, DE, DI, RE, RO, Y, Z
GND
J1
J2
J3
LK2
LK3
LK5, LK6
R1, R2
R3
RT1, RT2
U1
VCC
Description
Capacitor, 22 µF, Case C
Capacitor, 100 nF, 0805
Not placed/optional
Test point, yellow
Test point, black
2-way terminal block
4-way terminal block
6-way terminal block
8-pin (4 × 2) 0.1" header and shorting block
6-pin (3 × 2) 0.1" header and shorting block
Jumper Block, 2 pin, 0.1" spacing
Not placed/optional
Resistor, 0 Ω, 0805
Resistor, 120 Ω, 0805
14-lead SOIC (not placed)
Test point, red
Supplier/Part Number
AVX/TAJC226K016RNJ
Multicomp/MCCA000274
Not applicable
Vero Technologies/20-313140
Vero Technologies/20-2137
Lumberg/KRM 02
Lumberg/KRM 04
Lumberg/KRM 06
Harwin/M20-9953646 and Harwin/M7566-05
Harwin/M20-9953646 and Harwin/M7566-05
Harwin/M20-9990246 and Harwin/M7566-05
Not applicable
Vishay Draloric/CRCW08050000Z0EA
Multicomp/MC 0.1W 0805 1% 120R
Analog Devices/see Table 8
Vero Technologies/20-313137
Table 8. EVAL-RS485FDEBZ Options for U1(Full-Duplex RS-485 Transceivers, 14-Lead SOIC)
Enhanced ESD,
3.3 V Supply
ADM3070E
ADM3073E
LTC2852
ADM3076E
ADM3491E
Enhanced ESD,
5 V Supply
ADM1491E
LT1791
LT1791A
Enhanced ESD,
3.3 V to 5 V Supply
LTC2864-1
LTC2864-2
Standard,
3.3 V Supply
ADM3491
Standard,
5 V Supply
ADM489
ADM489A
LTC1687
LTC491
Select the appropriate U1 devices in addition to EVAL-RS485FDEBZ when ordering. Ensure that the device ordered includes an R in the
part number for SOIC devices, for example, ADM3070EARZ.
Rev. A | Page 15 of 16
UG-543
Evaluation Board User Guide
RELATED LINKS
Resource
AN-960
RS-485/RS-422 Products
Description
RS-485/RS-422 Circuit Implementation Guide
RS-485/RS-422 Product Selection
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2013–2019 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG11390-0-3/19(A)
Rev. A | Page 16 of 16
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Analog Devices Inc.:
EVAL-RS485HDEBZ EVAL-RS485FDEBZ EVAL-RS485FD8EBZ
工商网监
湘ICP备2023018690号
