HMC861LP3E
v01.0112
Typical Applications
Features
The HMC861LP3E is ideal for:
Low Noise Floor: -152 dBc/Hz at 100 kHz offset
• Satellite Communication Systems
Programmable Frequency Divider, N = 1 or 3
• Point-to-Point & Point-to-Multi-Point Radios
Wide Bandwidth 100 MHz to 13 GHz
• Military Applications
16 Lead 3X3 mm SMT Package: 9mm 2
TE
• Test Equipment
Functional Diagram
General Description
B
SO
LE
The HMC861LP3E is a low noise programmable
frequency divider in a 3 x 3 mm leadless
surface mount package. The divider can be
programmed to divide from N = 1,3 in the
100 MHz to 13 GHz input frequency range. The low
phase noise and wide frequency range make this
device ideal for high performance and wide band
communication systems.
Electrical Specifications, TA = +25 °C, Vcc1 = Vcc2 = +5V
Parameter
Conditions
Min.
Max RF Input Frequency
Sine Wave or Square Wave Input
13
Min RF Input Frequency [1]
Sine Wave or Square Wave Input
Typ.
Max.
Units
0.1
GHz
10
dBm
RF Input Characteristics
RF Input Power Range
-10
GHz
0
Divider Output Characteristics
O
Frequency Dividers & Detectors - SMT
13 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 3)
Output Power
(see the Pout plots for each division ratio)
Divider Ratio N
2
1
dBm
3
SSB Phase Noise @ 100 kHz Offset
Fin = 6 GHz, Pin = 0 dBm, N = 1
-152
dBc/Hz
SSB Phase Noise @ 100 kHz Offset
Fin = 6 GHz, Pin = 0 dBm, N = 3
-153
dBc/Hz
Logic Inputs
VIH Input High Voltage
3
5
V
VIL Input Low Voltage
0
0.4
V
5.25
V
Power Supplies
Vcc1, Vcc2
Analog Supply (See pin description table)
4.75
5
Current Consumption
Icc
Control Bits
N = 1, S0 = L
125
mA
N = 3, S0 = H
180
mA
1
Bit
[1] Square wave input waveform is recommended below 400 MHz for best phase noise performance. If sine wave input waveform is used below
400 MHz, it is recommended that power input is > +5 dBm for best operation including phase noise performance.
1
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 2delivery,
and to
placeChelmsford,
orders: Analog MA
Devices,
Inc.,
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Elizabeth
Drive,
01824
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC861LP3E
v01.0112
13 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 3)
Output Power vs.
Temperature, Pin = 0 dBm
Input Sensitivity vs. Temperature
6
15
4
OUTPUT POWER (dBm)
5
0
Min Pin +25C
Max Pin +25C
Min Pin +85C
Max Pin +85C
Min Pin -40C
Max Pin -40C
-5
-10
2
0
TE
INPUT POWER (dBm)
10
-15
-2
+25C
+85C
-40C
-4
-20
-6
-25
2
4
6
8
10
12
14
-160
-170
1.0e+2
1.0e+3
1.0e+4
1.0e+5
1.0e+6
-150
-160
1.0e+3
O
POWER LEVEL (dBm)
OUTPUT LEVEL (dBm)
1.0e+4
1.0e+5
1.0e+6
1.0e+7
-10
-20
-30
Pfeedthru
3rd Harmonic
6
+25C
+85C
-40C
0
-10
4
14
Reverse Leakage, Pin = 0 dBm
0
2
12
OFFSET FREQUENCY (Hz)
10
0
10
-140
-170
1.0e+2
1.0e+7
Output Harmonics, Pin = 0 dBm
-50
8
-130
OFFSET FREQUENCY (Hz)
-40
6
LE
100MHz SQ
100MHz SINE
6 GHz
13 GHz
-150
4
-120
B
SO
SSB PHASE NOISE (dBc/Hz)
-120
-140
2
Phase Noise vs. Temperature,
Fin = 6 GHz, Pin = 0 dBm
Phase Noise vs.
Frequency, Pin = 0 dBm
-130
0
INPUT FREQUENCY (GHz)
INPUT FREQUENCY (GHz)
SSB PHASE NOISE (dBc/Hz)
0
Frequency Dividers & Detectors - SMT
Divide-by-1
8
10
INPUT FREQUENCY (GHz)
12
14
-20
-30
Both Output Ports Terminated
One Output Port Terminated
-40
-50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
INPUT FREQUENCY (GHz)
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 2delivery,
and to
placeChelmsford,
orders: Analog MA
Devices,
Inc.,
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Elizabeth
Drive,
01824
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
2
HMC861LP3E
v01.0112
13 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 3)
Output Power vs.
Temperature, Pin = 0 dBm
Input Sensitivity vs. Temperature
6
15
4
OUTPUT POWER (dBm)
5
0
Min Pin +25C
Max Pin +25C
Min Pin +85C
Max Pin +85C
Min Pin -40C
Max Pin -40C
-5
-10
-15
0
-2
+25C
+85C
-40C
-4
-20
-6
-25
0
2
4
6
8
10
12
14
0
2
4
LE
-120
10
12
14
-140
-150
-160
B
SO
100MHz SQ
100MHz SINE
6 GHz
13 GHz
-130
1.0e+3
1.0e+4
1.0e+5
1.0e+6
SSB PHASE NOISE (dBc/Hz)
-120
-170
1.0e+2
-140
-150
-160
-170
1.0e+2
1.0e+7
O
Output Harmonics, Pin = 0 dBm
1.0e+3
1.0e+7
Both Output Ports Terminated
One Output Port Terminated
POWER LEVEL (dBm)
-20
-30
-40
Pfeedthru
3rd Harmonic
-50
6
1.0e+6
0
-10
-20
4
1.0e+5
Reverse Leakage, Pin = 0 dBm
-10
2
1.0e+4
OFFSET FREQUENCY (Hz)
0
0
+25C
+85C
-40C
-130
OFFSET FREQUENCY(Hz)
OUTPUT LEVEL (dBm)
8
Phase Noise vs. Temperature,
Fin = 6 GHz, Pin = 0 dBm
Phase Noise vs.
Frequency, Pin = 0 dBm
-60
6
INPUT FREQUENCY (GHz)
INPUT FREQUENCY (GHz)
10
8
10
INPUT FREQUENCY (GHz)
3
2
TE
INPUT POWER (dBm)
10
SSB PHASE NOISE (dBc/Hz)
Frequency Dividers & Detectors - SMT
Divide-by-3
12
-30
-40
-50
-60
-70
-80
-90
14
-100
1
2
3
4
5
6
7
8
9
10
11
12
13
14
INPUT FREQUENCY (GHz)
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 2delivery,
and to
placeChelmsford,
orders: Analog MA
Devices,
Inc.,
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Elizabeth
Drive,
01824
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC861LP3E
v01.0112
13 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 3)
Icc vs. Vcc
175
150
125
N=1
100
N=3
75
4.7
4.8
4.9
5
5.1
5.2
5.3
Absolute Maximum Ratings
LE
Vcc (V)
13 dBm
Supply Voltage (Vcc)
5.5V
Control Inputs (S0)
5.5V
Storage Temperature
-65 to +125 °C
ESD Sensitivity (HBM)
Class 1A
State
S0
Low
0 to 0.4V
High
3V to 5V
Programming Truth Table
for Frequency Division Ratios
B
SO
RF Input Power
Digital Control Input Voltages
S0
Divider Ratio (N)
0
1
1
3
0 = Logic Low 1 = Logic High
Note: Vcc1, Vcc2 must be applied before logic.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
O
Reliability Information
Junction Temperature to Maintain
1 Million Hour MTTF
150 °C
Nominal Junction Temperature
(T = 85 °C and Pin = 10 dBm))
108 °C
Thermal Resistance
(Junction to GND Paddle, 5V Supply)
25 °C/W
Operating Temperature
-40 to +85 °C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 2delivery,
and to
placeChelmsford,
orders: Analog MA
Devices,
Inc.,
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Elizabeth
Drive,
01824
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
Frequency Dividers & Detectors - SMT
200
TE
OPERATING CURRENT (mA)
225
4
HMC861LP3E
v01.0112
13 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 3)
5
TE
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
LE
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
PCB LAND PATTERN.
B
SO
Package Information
Part Number
Package Body Material
Lead Finish
HMC861LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL Rating
MSL1
[2]
Package Marking [1]
861
XXX
X
[1] 4-Digit lot number XXXX
[2] Max peak reflow temperature of 260 °C
O
Frequency Dividers & Detectors - SMT
Outline Drawing
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 2delivery,
and to
placeChelmsford,
orders: Analog MA
Devices,
Inc.,
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Elizabeth
Drive,
01824
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC861LP3E
v01.0112
13 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 3)
Pin Description
Description
Interface Schematic
1, 4, 8, 9,
12, 14, 15
GND
Ground: Backside of package has exposed metal ground slug which
must be connected to RF/DC ground.
2
IN
RF Input must be DC blocked.
3
NIN
RF Input 180° out of phase with pin 2 for differential operation.
AC ground for single ended operation.
5
S0
CMOS compatible division ratio control bit.
See programming truth table.
LE
B
SO
GND
Internally connected to circuitry, must be connected to RF/DC ground
for proper operation.
7
NC
The pins are not connected internally; however, all data shown
herein was measured with these pins connected to RF/DC ground
externally.
10
NOUT
Divider output 180° out of phase with pin 11.
RF output must be DC blocked.
O
6
11
OUT
Divided Output. RF output must be DC blocked.
13, 16
Vcc1, Vcc2
Supply voltage 5V. Connect both pins to +5V supply.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 2delivery,
and to
placeChelmsford,
orders: Analog MA
Devices,
Inc.,
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Elizabeth
Drive,
01824
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
Frequency Dividers & Detectors - SMT
Function
TE
Pin Number
6
HMC861LP3E
v01.0112
13 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 3)
TE
LE
B
SO
O
Frequency Dividers & Detectors - SMT
Evaluation PCB Schematic
NOTES:
1. The shorting link from PCB ground to pin 6 must be installed for proper operation.
2. Capacitors C1, C2, C3, and C4 are broadband multilayer capacitors, American Technical Ceramics part number
ATC530L. The 100 nF capacitance value is per ATC datasheet.
7
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 2delivery,
and to
placeChelmsford,
orders: Analog MA
Devices,
Inc.,
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Elizabeth
Drive,
01824
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC861LP3E
v01.0112
13 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 3)
O
List of Materials for Evaluation PCB Eval01-HMC861LP3E
Item
Description
J1 - J3
Connector, SMA, Female
J4
DC Connector Header, Molex 2mm
C1 - C4
100 nF Capacitor, Broadband, 0402
C5, C6
1000 pF Capacitor, 0402 Pkg.
C7, C8
4.7 uF Capacitor, 1206
R3
10 k Ohm Resistor, 0402
Vcc1, Vcc2
DC Pin, 0.040" Dia.
U1
HMC861LP3E, Programmable Divider
PCB [2]
119349 Evaluation Board
[1]
The circuit board used in the application should
use RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads and backside ground paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
Frequency Dividers & Detectors - SMT
B
SO
LE
TE
Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 2delivery,
and to
placeChelmsford,
orders: Analog MA
Devices,
Inc.,
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Elizabeth
Drive,
01824
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
8
工商网监
湘ICP备2023018690号
