HMC-C200

FEATURES FUNCTIONAL BLOCK DIAGRAM Frequency range: 8.0 GHz to 8.3 GHz Low SSB phase noise center frequency: −122 dBc/Hz at 10 kHz offset Voltage supply: 6 V to 15 V at a 116 mA supply current Internal voltage regulator Internal buffer amplifier High power output: 13.5 dBm −40°C to +85°C operating temperature range APPLICATIONS RFOUT 1 MT 5 VOLTAGE REGULATOR 2 VT Test and measurement equipment Lab instrumentation Industrial and medical equipment Military, electronic warfare (EW), electronic counter measures (ECM) communications 3 4 GND VDC 15397-001 Data Sheet 8 GHz to 8.3 GHz, Dielectric Resonator Oscillator Module HMC-C200 Figure 1. GENERAL DESCRIPTION The HMC-C200 is a high performance dielectric resonator oscillator (DRO) module that incorporates Analog Devices, Inc., ultralow phase noise technology and provides −122 dBc/Hz single sideband (SSB) phase noise at a 10 kHz offset. The output buffer also provides 13.5 dBm of power output. Internal temperature compensation allows this DRO to operate over a temperature range of −40°C to +85°C with a frequency drift rate of only 2 ppm/°C. The VT port accepts an analog tuning voltage from 2 V to 12 V and provides an electric tuning range of ±1 MHz from the center frequency. Rev. F The DRO is packaged in a small, moisture sealed 1.5 inch × 1.5 inch (36 mm × 36 mm) module with a field replaceable subminiature version A (SMA) connector. The HMC-C200 can be used as a drop in module if the SMA connector is not used. The HMC-C200 is available from 8.0 GHz to 8.3 GHz in 25 MHz frequency steps. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibilityis assumedby Analog Devices for its use, nor for anyinfringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2017 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com HMC-C200 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Pin Configuration and Function Descriptions..............................5 Applications ....................................................................................... 1 Interface Schematics .....................................................................5 Functional Block Diagram .............................................................. 1 Typical Performance Characteristics ..............................................6 General Description ......................................................................... 1 Theory of Operation .........................................................................7 Revision History ............................................................................... 2 DRO Tuning Procedure ................................................................7 Specifications..................................................................................... 3 Application Circuits ..........................................................................8 Electrical Specifications ............................................................... 3 Outline Dimensions ..........................................................................9 Absolute Maximum Ratings............................................................ 4 Ordering Guide .............................................................................9 ESD Caution .................................................................................. 4 REVISION HISTORY This Hittite Microwave Products data sheet has been reformatted to meet the styles and standards of Analog Devices, Inc. 3/2017—v06.0612 to Rev. F Updated Format .......................................................................... Universal Changes to Features Section and General Description Section........ 1 Changes to Table 1 ............................................................................ 3 Changes to Endnote 1, Table 2 ........................................................ 4 Changes to Table 3 ............................................................................ 5 Changed Application Notes Section to Theory of Operation Section ................................................................................................ 7 Changes to DRO Tuning Procedure Section ................................ 7 Added Application Circuits Section............................................... 8 Updated Outline Dimensions ......................................................... 9 Changes to Ordering Guide ............................................................ 9 Rev. F | Page 2 of 9 Data Sheet HMC-C200 SPECIFICATIONS ELECTRICAL SPECIFICATIONS TA = 25°C, frequency = 8.2 GHz, VDC = 6.5 V, unless otherwise noted. Table 1. Parameter FREQUENCY Range Min Accuracy Pushing Pulling Drift Rate Drift vs. Time POWER OUTPUT SSB PHASE NOISE, CENTER FREQUENCY At 1 kHz Offset At 10 kHz Offset At 100 kHz Offset At 1 MHz Offset TUNING VOLTAGE (VT) ELECTRIC TUNING RANGE HARMONIC DISTORTION Second, 2 fOUT Third, 3 fOUT OUTPUT RETURN LOSS VOLTAGE SUPPLY (VDC) SUPPLY CURRENT −250 Typ 8.0 12 −117 Max Units Test Conditions/Comments 8.3 GHz See the Ordering Guide for available frequencies +250 kHz kHz/V kHz p-p ppm/°C ppm/Year dBm 5 5 2 1 13.5 −95 −122 −140 −150 2 −1 12 +1 −28 −35 12 6 15 116 Rev. F | Page 3 of 9 Into 2:1 voltage standing wave ratio (VSWR) −40°C to +85°C At 25°C dBc/Hz dBc/Hz dBc/Hz dBc/Hz V MHz dBc dBc dB V mA VDC = 6.5 V HMC-C200 Data Sheet ABSOLUTE MAXIMUM RATINGS ESD CAUTION Table 2. Parameter VDC VT Storage Temperature Range Operating Temperature Range 1 Rating 15 V 0 V to 15 V −65°C to +150°C −40°C to +85°C1 While the HMC-C200 operates over this temperature range, it is not guaranteed that the specific frequency is in the tuning range at all temperatures. For additional options, contact a local Analog Devices sales or distribution representative for information on additional screening to ensure any required operation over temperature. Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Rev. F | Page 4 of 9 Data Sheet HMC-C200 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS RFOUT 1 5 VOLTAGE REGULATOR 2 VT 3 4 GND VDC 15397-002 MT Figure 2. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 Mnemonic RFOUT 2 VT 3 4 5 GND VDC MT Description Radio Frequency Output. RFOUT is ac-coupled and uses a female SMA connector. See Figure 3 for the interface schematic. Tuning Voltage. Control voltage and modulation input. Modulation bandwidth is 5 kHz for an ideal 2 V to 12 V source. See Figure 4 for the interface schematic. Ground. Must be connected to power supply ground. See Figure 5 for the interface schematic. Positive Power Supply Voltage. VDC = 6 V to 15 V. See Figure 6 for the interface schematic. Mechanical Tuning Screw. MT is set at the factory per the specified frequency of the customer. See Figure 7 for the interface schematic. 15397-003 Figure 3. RFOUT Interface Schematic Figure 6. VDC Interface Schematic 1000Ω 100pF 0.01µF 15397-004 VT VOLTAGE REGULATOR VDC MT Figure 4. VT Interface Schematic Figure 7. MT Interface Schematic 15397-005 GND 15397-007 RFOUT 15397-006 INTERFACE SCHEMATICS Figure 5. GND Interface Schematic Rev. F | Page 5 of 9 HMC-C200 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 0 –20 180 160 –40 VDC CURRRENT (mA) –60 –80 –100 –120 –140 140 120 100 80 60 40 –160 20 1k 10k 100k 1M OFFSET FREQUENCY (Hz) 0 –50 –40 –30 –20 –10 15397-008 –180 100 0 10 20 30 40 50 60 70 80 90 TEMPERATURE (°C) Figure 8. SSB Phase Noise vs. Offset Frequency for Various Temperatures at 8.2 GHz 15397-011 SSB PHASE NOISE (dBc/Hz) 200 +85°C +25°C –40°C Figure 11. VDC Current vs. Temperature at 8.2 GHz 20 8.202 15.0 8.201 12.5 8.200 10.0 8.199 7.5 16 14 OUTPUT POWER (dBm) FREQUENCY (GHz) OUTPUT POWER (dBm) 18 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) 8.198 15397-009 10 –60 7 8 9 10 11 5.0 12 VT (V) Figure 9. Output Power vs. Temperature at 8.2 GHz 15397-012 12 Figure 12. Frequency and Output Power vs. Tuning Voltage(VT) 8.2010 10µ 8.2005 SENSITIVITY (g2/Hz) 1µ 8.2000 8.1995 –40 –20 0 20 40 60 80 TEMPERATURE (°C) 100 Figure 10. Output Frequency vs. Temperature 1n 100 1k OFFSET FREQUENCY (Hz) Figure 13. Vibration Sensitivity vs. Offset Frequency Rev. F | Page 6 of 9 10k 15397-013 8.1990 –60 0.1µ 10n 15397-010 OUTPUT FREQUENCY (GHz) Y-AXIS (PARALLEL TO CONNECTORS) X-AXIS (PERPENDICULAR TO CONNECTORS) Z-AXIS Data Sheet HMC-C200 THEORY OF OPERATION DRO TUNING PROCEDURE The DRO turning procedure is as follows: 1. 2. 3. 4. 5. A mechanical tuning (MT) screw is provided on the HMCC200, which can adjust the center frequency by approximately ±20 MHz from the factory setting. This screw is set at the factory per the specified frequency of the customer, as outlined in the Ordering Guide section. Adjusting the screw clockwise increases the frequency, while turning the screw counterclockwise decreases the frequency. The MT screw has stops at either end of its approximately 8 turn range. Do not attempt to force the screw past the stops. Connect the RF output to a spectrum analyzer and adjust the MT screw to set the output frequency within 1 MHz of the desired value. Set the spectrum analyzer settings for a 10 MHz span centered on the desired output frequency. Change the reference value of the spectrum analyzer approximately 15 dBm and change the vertical scale to 1 dB per division so the peak oscillation frequency is visible on the screen. Use the tuning voltage (VT) on Pin 2 to maximize the DRO output power and note the frequency. The tuning voltage must not be adjusted higher than 15 V. If the frequency is meeting the new requirement and the output power is greater than 12 dBm, the tuning procedure is complete. If the frequency is not meeting the requirement, carefully readjust the MT screw and VT until the output frequency is within the required range. The VT sustains oscillation over a fairly narrow range (approximately 1 MHz) before output power, temperature stability, and phase noise performance starts to degrade. In some cases, it is possible for the VT to be adjusted to the point where oscillation stops. Therefore, use the MT screw as a coarse tune, and use the VT effectively as a fine tune. In phase-locked loop (PLL) applications where the VT is used within the loop, this limited voltage range must be considered during the design of the loop. Use limiting circuit must be used to keep the VT voltage within the optimal range. If the output power is less than 12 dBm, the DRO may be at the correct frequency; however, the phase noise performance and stability over temperature may degrade. It is recommended that the customer verify phase noise and stability after custom tuning. Rev. F | Page 7 of 9 HMC-C200 Data Sheet APPLICATION CIRCUITS RFOUT VOLTAGE REGULATOR 1mH 100µF VT 0.01µF GND VDC VDC 100pF 100pF 0.01µF 15397-014 MT VT Figure 14. Fixed Output Frequency Application RFOUT VOLTAGE REGULATOR MT VT GND VDC VDC OP AMP LIMITING CIRCUIT VTUNE 100pF 0.01µF DIVIDER REFERENCE 15397-015 ÷N PHASE DETECTOR Figure 15. Phase Locked Application Rev. F | Page 8 of 9 Data Sheet HMC-C200 OUTLINE DIMENSIONS 1.50 (38.10) SQ 0.75 (19.05) 0.89 (22.61) 0.200 (5.08) 0.080 (2.03) 1 Field Replaceable Female SMA Connector 1.34 (34.04) SQ 5 2 4 Ø 0.098 (2.49) TOP VIEW SIDE VIEW 1.05 (26.67) 0.210 (5.33) 01-24-2017-A 0.270 (6.86) PKG-000000 0.615 (15.62) 0.135 (3.43) 3 Figure 16. 5-Lead Connectorized Hermetic Module [MODULE] (ML-5-3) Dimensions shown in inches and (millimeters) ORDERING GUIDE Model HMC-C200-8000 HMC-C200-8025 HMC-C200-8050 HMC-C200-8075 HMC-C200-8100 HMC-C200-8125 HMC-C200-8150 HMC-C200-8175 HMC-C200-8200 HMC-C200-8225 HMC-C200-8250 HMC-C200-8275 HMC-C200-8300 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Module Description 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] 5-Lead Connectorized Hermetic Module [MODULE] ©2017 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D15397-0-3/17(F) Rev. F | Page 9 of 9 Package Option ML-5-3 ML-5-3 ML-5-3 ML-5-3 ML-5-3 ML-5-3 ML-5-3 ML-5-3 ML-5-3 ML-5-3 ML-5-3 ML-5-3 ML-5-3