HMC334LP4 / 334LP4E
v03.0410
Features
The HM334LP4(E) is ideal for:
Conversion Loss: 0 dB
• Basestations & Repeaters
LO to RF Isolation: 48 dB
• GSM, GPRS & Edge
Single-Ended LO Drive: -6 to +6 dBm
• CDMA, W-CDMA & TD-SCDMA
Input IP3: +26 dBm
• WiMAX & LTE
SSB Noise Figure: 11 dB
TE
Typical Applications
On-Chip RF Balun
24 Lead 4x4mm QFN Package: 16 mm2
General Description
Functional Diagram
LE
The HMC334LP4(E) is a low noise, wideband
downconverter RFIC which is ideal for Cellular/3G
and WiMAX/4G applications from 0.6 to 2.7 GHz.
The LO input accepts drive levels from -6 to +6 dBm
while the RFIC provides 48 dB of LO to RF isolation,
and 0 dB conversion loss. The HMC334LP4(E) will
support an IF output bandwidth of up to 600 MHz
and consumes only 173 mA from a +5V supply.
This wideband active mixer also provides excellent
performance in the presence of high level “Blocker”
signals, making it ideal for receiver applications in
demanding environments.
B
SO
MIXERS - DOWNCONVERTERS - SMT
9
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Electrical Specifi cations,
O
TA = +25 °C, LO = 0 dBm*, VSLO = VSIF = +5V, IF = 240 MHz
Parameter
Min.
Typ.
Max.
Units
Frequency Range, RF
0.6 - 2.7
Frequency Range, LO
0.35 - 3.0
GHz
Frequency Range, IF
1 - 600
MHz
Conversion Gain (IF XFMR Included)
GHz
-5
-1
11
dB
30
48
dB
IF Output Impedance (Diff)
200
Ohms
IP3 (Input)
+26
dBm
12
dBm
SSB Noise Figure
LO to RF Isolation
1 dB Compression (Input)
LO Drive Input Level
Supply Current
8.5
dB
-6 to +6
173
dBm
225
mA
*Unless otherwise noted all measurements with R1 = 13 Ohms and single-ended 50 Ohm IF output with Port J2 or J3 shorted to ground.
9 - 38
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery,
andRoad,
to place
orders: Analog
Devices,
For price,
delivery
and
to for
place
Hittite Microwave
Corporation,
20 Alpha
Chelmsford,
MA
01824Inc.,
responsibility
is assumed
by Analog
Devices
its use,orders:
nor for any infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Conversion Gain vs. Temperature
@ LO = 0 dBm, IF = 100 MHz [1]
5
5
0
-5
-15
-20
0.6
1
1.4
1.8
2.2
2.6
-20
0.6
3
2.2
2.6
3
-3 dBm
0 dBm
+3 dBm
1
1.4
1.8
2.2
2.6
5
0
-5
-10
+25 C
+85 C
-40 C
-15
-20
0.6
3
1
RF FREQUENCY (GHz)
25
20
20
15
15
P1dB (dBm)
25
10
5
+25C
+85C
-40C
0
1.4
1.8
2.2
2.6
3
2.6
3
RF FREQUENCY (GHz)
P1dB vs. Temperature
@ LO = 0 dBm, IF = 240 MHz [1]
O
P1dB vs. Temperature
@ LO = 0 dBm, IF = 100 MHz [1]
P1dB (dBm)
1.8
LE
B
SO
CONVERSION LOSS (dB)
0
10
5
+25C
+85C
-40C
0
-5
-10
0.6
1.4
10
5
-20
0.6
1
Conversion Gain vs. Temperature
@ LO = 0 dBm, IF = 240 MHz [1]
10
-15
+25 C
+85 C
-40 C
-10
RF FREQUENCY (GHz)
Conversion Gain vs.
LO Drive, IF = 240 MHz [1]
-10
-5
-15
RF FREQUENCY (GHz)
-5
0
TE
-3 dBm
0 dBm
+3 dBm
-10
9
MIXERS - DOWNCONVERTERS - SMT
10
CONVERSION LOSS (dB)
10
CONVERSION LOSS (dB)
CONVERSION LOSS (dB)
Conversion Gain vs.
LO Drive, IF = 100 MHz [1]
-5
1
1.4
1.8
2.2
2.6
3
RF FREQUENCY (GHz)
-10
0.6
1
1.4
1.8
2.2
RF FREQUENCY (GHz)
[1] LO < RF
* Unless otherwise noted all measurements with R1= 13 Ohms
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery,
andRoad,
to place
orders: Analog
Devices,
For price,
delivery
and
to for
place
Hittite Microwave
Corporation,
20 Alpha
Chelmsford,
MA
01824Inc.,
responsibility
is assumed
by Analog
Devices
its use,orders:
nor for any infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
9 - 39
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Input IP3 vs. Temperature
@ LO = 0 dBm, IF = 100 MHz [1]
Input IP3 vs. LO Drive, IF = 100 MHz [1]
35
30
30
25
25
IP3 (dBm)
35
20
15
1
1.4
1.8
2.2
2.6
0
0.6
3
3
2.6
3
Input IP3 vs. Temperature
@ LO = 0 dBm, IF = 240 MHz [1]
B
SO
-3 dBm
0 dBm
+3 dBm
1
1.4
1.8
2.2
2.6
25
20
15
+25C
+85C
-40C
10
5
0
0.6
3
1
RF FREQUENCY (GHz)
1.4
1.8
2.2
RF FREQUENCY (GHz)
RF Return Loss @ LO = 0 dBm [1]
O
Noise Figure [1]
25
20
10
+25 C
+85 C
-40 C
RF RETURN LOSS (dB)
SSB NOISE FIGURE (dB)
2.6
30
25
15
10
5
0
0.6
2.2
35
30
0
0.6
1.8
40
35
5
1.4
LE
40
10
1
RF FREQUENCY (GHz)
Input IP3 vs. LO Drive, IF = 240 MHz [1]
15
+25C
+85C
-40C
5
RF FREQUENCY (GHz)
20
15
10
5
0
0.6
20
TE
-3 dBm
0 dBm
+3 dBm
IP3 (dBm)
IP3 (dBm)
40
10
IP3 (dBm)
MIXERS - DOWNCONVERTERS - SMT
9
40
RF
LO
0
-10
-20
-30
-40
1
1.4
1.8
2.2
2.6
3
RF FREQUENCY (GHz)
0
0.5
1
1.5
2
2.5
3
RF FREQUENCY (GHz)
[1] LO < RF
* Unless otherwise noted all measurements with R1= 13 Ohms
9 - 40
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery,
andRoad,
to place
orders: Analog
Devices,
For price,
delivery
and
to for
place
Hittite Microwave
Corporation,
20 Alpha
Chelmsford,
MA
01824Inc.,
responsibility
is assumed
by Analog
Devices
its use,orders:
nor for any infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
LO - RF Isolation @ LO = 0 dBm [1]
50
50
40
30
LO TO IF
RF TO IF
10
0
0.6
1
1.4
1.8
2.2
2.6
LE
0
B
SO
CONVERSION LOSS (dB)
1.8
2.2
2.6
3
Noise Figure, IF = 184 MHz, USB [2]
+25 C
+85 C
-40 C
1
1.4
1.8
2.2
2.6
20
10
5
0
0.6
3
Input IP3 vs.
LO Drive, IF = 184 MHz, USB [2]
1
O
35
30
30
25
25
IP3 (dBm)
40
20
-3 dBm
0 dBm
+3 dBm
2.2
2.6
3
20
15
+25C
+85C
-40C
10
5
0
0.6
1.8
Input IP3 vs. Temperature
@ LO = 0 dBm, IF = 184 MHz, USB [2]
35
10
1.4
RF FREQUENCY (GHz)
40
15
+25 C
+85 C
-40 C
15
RF FREQUENCY (GHz)
IP3 (dBm)
1.4
25
5
-20
0.6
1
RF FREQUENCY (GHz)
10
-15
IF = 100MHz
IF = 240MHz
20
0
0.6
3
Conversion Gain vs.
Temperature, IF = 184 MHz, USB [2]
-10
30
10
RF FREQUENCY (GHz)
-5
40
TE
20
9
MIXERS - DOWNCONVERTERS - SMT
60
ISOLATION (dB)
60
SSB NOISE FIGURE (dB)
ISOLATION (dB)
Isolation @ LO = 0 dBm, IF = 100 MHz [1]
5
1
1.4
1.8
2.2
RF FREQUENCY (GHz)
2.6
3
0
0.6
1
1.4
1.8
2.2
2.6
3
RF FREQUENCY (GHz)
[1] LO < RF
[2] LO > RF
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery,
andRoad,
to place
orders: Analog
Devices,
For price,
delivery
and
to for
place
Hittite Microwave
Corporation,
20 Alpha
Chelmsford,
MA
01824Inc.,
responsibility
is assumed
by Analog
Devices
its use,orders:
nor for any infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
9 - 41
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Typical Supply
Current vs. Supply Voltage
Absolute Maximum Ratings
RF Input (VSLO = VSIF= +5V)
+21 dBm
VSLO = VSIF (V)
ISLO + ISIF (mA)
LO Drive (VSLO = VSIF= +5V)
+12 dBm
+4.5
146
VccLO, VccIF
+6 Vdc
+5.0
173
Channel Temperature
150 °C
+5.5
200
Continuous Pdiss (T = 85°C)
(derate 27.8 mW/°C above 85°C)
1.8 W
Thermal Resistance
(channel to ground paddle)
36 °C/W
Storage Temperature
-65 to 150 °C
Operating Temperature
-40 to 85 °C
TE
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
LE
Outline Drawing
Downconverter will operate over full voltage range shown above.
B
SO
MIXERS - DOWNCONVERTERS - SMT
9
NOTES:
O
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC334LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC334LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H334
XXXX
[2]
H334
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
9 - 42
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery,
andRoad,
to place
orders: Analog
Devices,
For price,
delivery
and
to for
place
Hittite Microwave
Corporation,
20 Alpha
Chelmsford,
MA
01824Inc.,
responsibility
is assumed
by Analog
Devices
its use,orders:
nor for any infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Pin Descriptions
Interface Schematic
1
VccLO
Supply for LO Amplifier.
Draws approximately 120mA from VSLO.
A 13 Ohm resistor (R1) must be connected
externally between the VSLO supply and the
VccLO pin. See evaluation PCB schematic.
2, 5, 8, 11,
14, 17, 20, 23
GND
These pins and the ground paddle should be
connected to a high quality RF/DC ground.
3
LOP
LO Input Port. This pin needs a DC blocking capacitor.
(Typical voltage on this pin will be 1.5 - 1.8V)
4
LON
For single ended applications, this pin should be AC
grounded
6, 7, 12,
21, 22, 24
9, 10
N/C
IFN, IFP
LE
The pins are not connected internally; however, all data
shown herein was measured with these pins connected to
RF/DC ground externally.
Differential baseband outputs, 200 ohm differential output
impedance. Each port should draw approximately 25mA
from VSIF without LO power and 28mA from VSIF with LO
power on.
9
MIXERS - DOWNCONVERTERS - SMT
Description
TE
Function
B
SO
Pin Number
O
For single-ended 50 Ohm operation, port J2 or J3 should be
shorted to RF/DC ground. See evaluation PCB schematic.
13, 18
CTRF
Center tap of the RF transformer. Biased at 2.2V when connected to ground through two 91 ohm resistors.
15
GNDRF
Pin to be connected to a high quality RF/DC ground. Also
can be used to drive the RF port differentially if needed.
16
RF
50 Ohms impedance can be matched
from 600 - 3000 MHz.
VccIF
Supply decoupling for the mixer stage.
(Typical voltage on this pin will be 4.8V)
Connect C3 to a high quality RF/DC
ground per evaluation PCB schematic.
19
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery,
andRoad,
to place
orders: Analog
Devices,
For price,
delivery
and
to for
place
Hittite Microwave
Corporation,
20 Alpha
Chelmsford,
MA
01824Inc.,
responsibility
is assumed
by Analog
Devices
its use,orders:
nor for any infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
9 - 43
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Evaluation PCB
TE
LE
B
SO
MIXERS - DOWNCONVERTERS - SMT
9
List of Materials for Evaluation PCB 117528 [1]
Item
J1 - J4
Johnson SMA Connector
2mm SMT
O
J5 - J6
Description
C1 - C3
1000 pF Capacitor, 0402 Pkg.
C4
0.3 pF Capacitor, 0402 Pkg.
C5
100 pF Capacitor, 0402 Pkg.
C6
10 KpF Capacitor, 0402 Pkg.
C7
1.3 pF Capacitor, 0402 Pkg.
C8, C9
0.1 μF Capacitor, 0805 Pkg.
L1
2.7 nH Chip Inductor, 0603 Pkg.
L2
2 nH Chip Inductor, 0603 Pkg.
R1
13 Ohm Resistor, 1206 Pkg.
R2, R3
91 Ohm Resistor, 0805 Pkg.
T1
M/A-Com 4:1 Balun, MABAES0061
U1
HMC334LP4 / HMC334LP4E
PCB [2]
117527 Evaluation Board
The circuit board used in the final application
should use RF circuit design techniques. Signal
lines should have 50 Ohm impedance while the
package ground leads and exposed paddle should
be connected directly to the ground plane similar
to that shown. A sufficient number of via holes
should be used to connect the top and bottom
ground planes. The evaluation circuit board shown
is available from Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
9 - 44
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery,
andRoad,
to place
orders: Analog
Devices,
For price,
delivery
and
to for
place
Hittite Microwave
Corporation,
20 Alpha
Chelmsford,
MA
01824Inc.,
responsibility
is assumed
by Analog
Devices
its use,orders:
nor for any infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Evaluation PCB Schematic
MIXERS - DOWNCONVERTERS - SMT
O
B
SO
LE
TE
9
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery,
andRoad,
to place
orders: Analog
Devices,
For price,
delivery
and
to for
place
Hittite Microwave
Corporation,
20 Alpha
Chelmsford,
MA
01824Inc.,
responsibility
is assumed
by Analog
Devices
its use,orders:
nor for any infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373 Phone:
Order781-329-4700
On-line at www.hittite.com
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
9 - 45
工商网监
湘ICP备2023018690号
