HMCAD1050-40

HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Features General Description • 13-bit resolution The HMCAD1050-40 is a high performance low power dual analog-to-digital converter (ADC). The ADC employs internal reference circuitry, a CMOS control interface, CMOS output data and is based on a proprietary structure. Digital error correction is employed to ensure no missing codes in the complete full scale range. • 20/40 MSPS Maximum Sampling Rate • Ultra-Low Power Dissipation: 30/55 mW • 72.5 dB SNR @ 8 MHz FIN • Internal Reference Circuitry • 1.8 V Core Supply Voltage • 1.7 - 3.6 V I/O supply voltage • Parallel CMOS output • 9 x 9 mm 64-Pin QFN (LP9E) Package 0 • Dual Channel Typical Applications A / D Converters - SMT • Handheld Communication, PMR, SDR • Medical Imaging • Portable Test Equipment • Digital Oscilloscopes • Baseband / IF Communication Several idle modes with fast startup times exist. Each channel can be independently powered down and the entire chip can either be put in Standby Mode or Power Down mode. The different modes are optimized to allow the user to select the mode resulting in the lowest possible energy consumption during idle mode and startup. The HMCAD1050-40 has a highly linear THA optimized for frequencies up to 70 MHz. The differential clock interface is optimized for low jitter clock sources and supports LVDS, LVPECL, sine wave and CMOS clock inputs. Pin compatible with HMCAD1040-40, HMCAD1040-80 and HMCAD1050-80. • Video Digitizing • CCD Digitizing Functional Diagram Figure 1. Functional Block Diagram 0-1 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Electrical Specifications DC Electrical Specifications AVDD=1.8V, DVDD=1.8V, DVDDCK=1.8V, OVDD=2.5V, 20/40MSPS clock, 50% clock duty cycle, -1dBFS 8MHz input signal, 13 bit output, unless otherwise noted Parameter Condition Min Typ Max Unit ±6 %FS DC accuracy Guaranteed Offset error Midscale offset Gain error Full scale range deviation from typical 1 LSB Gain matching Gain matching between channels. ± 3 sigma value at worst case conditions ± 0.5 %FS DNL Differential nonlinearity (12-bit level) ± 0.2 LSB INL Integral nonlinearity (12-bit level) ± 0.6 LSB VCM Common mode voltage output VAVDD/2 V Analog Input VCM -0.1 VCM +0.2 V Input common mode Analog input common mode voltage Full scale range, Normal Differential input voltage range, 2 Vpp Full scale range, Option Differential input voltage range, 1V (see section Reference Voltages) 1 Vpp Input capacitance Differential input capacitance Bandwidth Input Bandwidth 500 Core Supply Voltage Supply voltage to all 1.8V domain pins. See Pin Configuration and Description 1.7 1.8 2 V I/O Supply Voltage Output driver supply voltage (OVDD). Should be higher than or equal to Core Supply Voltage (VOVDD ≥ VDVDD) 1.7 2.5 3.6 V 2 0 pF MHz Power Supply Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com A / D Converters - SMT No missing codes 0-2 HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter AC Electrical Specifications - 20 MSPS AVDD= 1.8V, DVDD= 1.8V, DVDDCK= 1.8V, OVDD= 2.5V, FS=20 MSPS clock, 50% clock duty cycle, -1 dBFS 8 MHz input signal, 13 bit output, unless otherwise noted. Parameter Condition Min Typ Max Unit 71.5 72.2 dBFS FIN =~ FS/2 72.1 dBFS FIN = 20 MHz 71.6 dBFS Performance SNR Signal to Noise Ratio FIN = 2 MHz FIN = 8 MHz SNDR 72.5 Signal to Noise and Distortion Ratio FIN = 2 MHz 72.4 dBFS 72 dBFS FIN =~ FS/2 71.7 dBFS FIN = 20 MHz 71.3 dBFS 87 dBc FIN = 8 MHz 0 SFDR 71 Spurious Free Dynamic Range A / D Converters - SMT FIN = 2 MHz FIN = 8 MHz HD2 75 85 dBc FIN =~ FS/2 80 dBc FIN = 20 MHz 80 dBc -90 dBc Second order Harmonic Distortion FIN = 2 MHz FIN = 8 MHz HD3 -85 -95 dBc FIN =~ FS/2 -95 dBc FIN = 20 MHz -95 dBc -87 dBc Third order Harmonic Distortion FIN = 2 MHz FIN = 8 MHz ENOB -75 -85 dBc FIN =~ FS/2 -80 dBc FIN = 20 MHz -80 dBc 11.7 bits Effective number of Bits FIN = 2 MHz FIN = 8 MHz 11.5 11.7 bits 11.6 bits FIN = 20 MHz 11.6 bits Signal crosstalk between channels, FIN1 = 8MHz, FIN0 = 9.9MHz -105 dB FIN =~ FS/2 Crosstalk dBFS Power Supply Analog supply current 11.6 mA Digital core supply 1.8 mA Output driver supply 2.5V output driver supply, sine wave input, FIN = 1 MHz, CK_EXT enabled 2.9 mA Output driver supply 2.5V output driver supply, sine wave input, FIN = 1 MHz, CK_EXT disabled 2.4 mA 20.9 mW Digital supply current Analog power Digital power Dissipation OVDD = 2.5V, ~5pF load on output bits, FIN = 1 MHz, CK_EXT disabled 9.2 mW Total power Dissipation OVDD = 2.5V, ~5pF load on output bits, FIN = 1 MHz, CK_EXT disabled 30.1 mW 9.9 µW Sleep Mode 1 Power Dissipation, Sleep mode one channel 20.5 mW Sleep Mode 2 Power Dissipation, Sleep mode both channels 9.2 mW Power Down Dissipation Clock Inputs Max. Conversion Rate Min. Conversion Rate 0-3 20 MSPS 3 MSPS Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter AC Electrical Specifications - 40 MSPS AVDD=1.8V, DVDD=1.8V, DVDDCK=1.8V, OVDD=2.5V, FS=40MSPS clock, 50% clock duty cycle, -1dBFS 8MHz input signal, 13 bit output, unless otherwise noted. Parameter Condition Min Typ Max Unit Performance Signal to Noise Ratio FIN = 2 MHz FIN = 8 MHz SNDR 72.5 71.9 dBFS FIN =~ FS/2 72 dBFS FIN = 30 MHz 70.8 dBFS Signal to Noise and Distortion Ratio FIN = 2 MHz FIN = 8 MHz SFDR 71 71.5 dBFS 71.2 dBFS 81 dBc Spurious Free Dynamic Range 81 dBc FIN =~ FS/2 75 80 dBc FIN = 30 MHz 80 dBc -90 dBc Second order Harmonic Distortion FIN = 2 MHz FIN = 8 MHz -95 dBc FIN =~ FS/2 -95 dBc -85 FIN = 30 MHz -90 dBc -81 dBc Third order Harmonic Distortion FIN = 2 MHz FIN = 8 MHz ENOB -75 -81 dBc FIN =~ FS/2 -80 dBc FIN = 30 MHz -80 dBc 11.6 bits Effective number of Bits FIN = 2 MHz FIN = 8 MHz 11.5 11.7 bits 11.6 bits FIN = 30 MHz 11.5 bits Signal crosstalk between channels, FIN1 = 8MHz, FIN0 = 9.9MHz -100 dB 21.1 mA FIN =~ FS/2 Crosstalk dBFS dBFS FIN =~ FS/2 FIN = 8 MHz HD3 71.7 72.1 FIN = 30 MHz FIN = 2 MHz HD2 dBFS 72.7 Power Supply Analog supply current Digital supply current Digital core supply 3.3 mA Output driver supply 2.5V output driver supply, sine wave input, FIN = 1 MHz, CK_EXT enabled 5.3 mA Output driver supply 2.5V output driver supply, sine wave input, FIN = 1 MHz, CK_EXT disabled 4.4 mA 38 mW Analog power Dissipation Digital power Dissipation OVDD = 2.5V, ~5pF load on output bits, FIN = 1 MHz, CK_EXT disabled 16.9 mW Total power Dissipation OVDD = 2.5V, ~5pF load on output bits, FIN = 1 MHz, CK_EXT disabled 54.9 mW Power Down Dissipation 9.7 µW Sleep Mode 1 Power Dissipation, Sleep mode one channel 36.1 mW Sleep Mode 2 Power Dissipation, Sleep mode both channels 14.2 mW 0 A / D Converters - SMT SNR Clock Inputs Max. Conversion Rate Min. Conversion Rate 40 MSPS 3 MSPS Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com 0-4 HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Digital and Timing Specifications AVDD= 1.8V, DVDD= 1.8V, DVDDCK= 1.8V, OVDD= 2.5V, Conversion Rate: Max specified, 50% clock duty cycle, -1 dBFS input signal, 5 pF capacitive load on data outputs, unless otherwise noted Parameter Condition Min Typ Max Unit 80 % high Clock Inputs Duty Cycle 20 Compliance CMOS, LVDS, LVPECL, Sine Wave Input range Differential input swing 0.4 Input range Differential input swing, sine wave clock input 1.6 Input common mode voltage Keep voltages within ground and voltage of OVDD 0.3 Input capacitance Differential Vpp Vpp VOVDD -0.3 V 2 pF Timing A / D Converters - SMT 0 0-5 TPD Start up time from Power Down Mode to Active Mode 900 TSLP Start up time from Sleep Mode to Active Mode 20 TOVR Out of range recovery time TAP Aperture Delay 0.8 ns Єrms Aperture jitter < 0.5 ps 1 clock cycles clock cycles clock cycles TLAT Pipeline Delay TD Output delay (see timing diagram). 5pF load on output bits 3 12 10 clock cycles ns TDC Output delay relative to CK_EXT (see timing diagram) 1 6 ns Logic Inputs VHI High Level Input Voltage. VOVDD ≥ 3.0V 2 V VHI High Level Input Voltage. VOVDD = 1.7V – 3.0V 0.8 ·VOVDD V VLI Low Level Input Voltage. VOVDD ≥ 3.0V 0 0.8 VLI Low Level Input Voltage. VOVDD = 1.7V – 3.0V 0 0.2 ·VOVDD V IHI High Level Input leakage Current ±10 µA ILI Low Level Input leakage Current ±10 µA CI Input Capacitance 3 V pF Logic Outputs VHO High Level Output Voltage VLO Low Level Output Voltage VOVDD -0.1 0.1 V V CL Max capacitive load. Post-driver supply voltage equal to digital supply voltage VOVDD = VDVDD 5 pF CL Max capacitive load. Post-driver supply voltage above 2.25V (1) 10 pF (1) The outputs will be functional with higher loads. However, it is recommended to keep the load on output data bits as low as possible to keep dynamic currents and resulting switching noise at a minimum Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Timing Diagram Figure 2: Timing Diagram Absolute Maximum Ratings Absolute maximum ratings are limiting values to be applied for short periods of time. Exposure to absolute maximum rating conditions for an extended period of time may reduce device lifetime. Table 1: Pin Pin Rating AVDD AVSS -0.3V to +2.3V DVDD DVSS -0.3V to +2.3V AVSS, DVSSCK, DVSS, OVSS DVSS -0.3V to +0.3V -0.3V to +3.9V OVDD OVSS IPx, INx, analog inputs and outputs AVSS -0.3V to +2.3V Digital outputs OVSS -0.3V to +3.9V CKP, CKN DVSSCK -0.3V to +3.9V Digital Inputs OVSS -0.3V to +3.9V Operating temperature -40 to +85 ºC Storage temperature -60 to +150 ºC Soldering Profile Qualification J-STD-020 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com A / D Converters - SMT 0 0-6 HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Pin Configuration and Description A / D Converters - SMT 0 0-7 Figure 3: Package Drawing, 64-pin QFN or TQFP Table 2: Pin Function Pin # Name Description 1, 18, 23 DVDD Digital and I/O-ring pre driver supply voltage, 1.8V 2 CM_EXT Common Mode voltage output 3, 9, 12 AVDD Analog supply voltage, 1.8V 4, 5, 8 AVSS Analog ground 6, 7 IP0, IN0 Analog input Channel 0 (non-inverting, inverting) 10, 11 IP1, IN1 Analog input Channel 1 (non-inverting, inverting) 13 DVSSCK Clock circuitry ground 14 DVDDCK Clock circuitry supply voltage, 1.8V 15 CKP Clock input, non-inverting (Format: LVDS, LVPECL, CMOS/TTL, Sine Wave) 16 CKN Clock input, inverting. For CMOS input on CKP, connect CKN to ground. 17, 64 DVSS Digital circuitry ground 19 CK_EXT_EN CK_EXT signal enabled when low (zero). Tristate when high. 20 DFRMT Data format selection. 0: Offset Binary, 1: Two’s Complement Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Table 2: Pin Function Name Description 21 PD_N Full chip Power Down mode when Low. All digital outputs reset to zero. After chip power up always apply Power Down mode before using Active Mode to reset chip. 22 OE_N_1 Output Enable Channel 0. Tristate when high 24, 41, 58 OVDD I/O ring post-driver supply voltage. Voltage range 1.7 to 3.6V 25, 40, 57 OVSS Ground for I/O ring 26 D1_0 Output Data Channel 1 (LSB, 13 bit output or 1Vpp full scale range ) 27 D1_1 Output Data Channel 1 (LSB, 12 bit output 2Vpp full scale range) 28 D1_2 Output Data Channel 1 29 D1_3 Output Data Channel 1 30 D1_4 Output Data Channel 1 31 D1_5 Output Data Channel 1 32 D1_6 Output Data Channel 1 33 D1_7 Output Data Channel 1 34 D1_8 Output Data Channel 1 35 D1_9 Output Data Channel 1 36 D1_10 Output Data Channel 1 37 D1_11 Output Data Channel 1 (MSB for 1Vpp full scale range, see Reference Voltages section) 38 D1_12 Output Data Channel 1 (MSB for 2Vpp full scale range) 39 ORNG_1 Out of Range flag Channel 1. High when input signal is out of range 42 CK_EXT Output clock signal for data synchronization. CMOS levels 43 D0_0 Output Data Channel 0 (LSB, 13 bit output or 1Vpp full scale range) 44 D0_1 Output Data Channel 0 (LSB, 12 bit output 2Vpp full scale range) 45 D0_2 Output Data Channel 0 46 D0_3 Output Data Channel 0 47 D0_4 Output Data Channel 0 48 D0_5 Output Data Channel 0 49 D0_6 Output Data Channel 0 50 D0_7 Output Data Channel 0 51 D0_8 Output Data Channel 0 52 D0_9 Output Data Channel 0 53 D0_10 Output Data Channel 0 54 D0_11 Output Data Channel 0 (MSB for 1Vpp full scale range, see Reference Voltages section) 55 D0_12 Output Data Channel 0 (MSB for 2Vpp full scale range) 56 ORNG_0 Out of Range flag Channel 0. High when input signal is out of range 59 OE_N_0 Output Enable Channel 0. Tristate when high 60, 61 CM_EXTBC_1, CM_ EXTBC_0 Bias control bits for the buffer driving pin CM_EXT 00: OFF 01: 50uA 10: 500uA 11: 1mA 62, 63 SLP_N_1, SLP_N_0 Sleep Mode 00: Sleep Mode 01: Channel 0 active 10: Channel 1 active 11: Both channels active Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com 0 A / D Converters - SMT Pin # 0-8 HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Recommended Usage Analog Input The analog inputs to the HMCAD1050-40 is a switched capacitor track-and-hold amplifier optimized for differential operation. Operation at common mode voltages at mid supply is recommended even if performance will be good for the ranges specified. The CM_EXT pin provides a voltage suitable as common mode voltage reference. The internal buffer for the CM_EXT voltage can be switched off, and driving capabilities can be changed by using the CM_EXTBC control input. A / D Converters - SMT 0 Figure 4 shows a simplified drawing of the input network. The signal source must have sufficiently low output impedance to charge the sampling capacitors within one clock cycle. A small external resistor (e.g. 22 Ohm) in series with each input is recommended as it helps reducing transient currents and dampens ringing behavior. A small differential shunt capacitor at the chip side of the resistors may be used to provide dynamic charging currents and may improve performance. The resistors form a low pass filter with the capacitor, and values must therefore be determined by requirements for the application. Detailed configuration and usage instructions must be found in the documentation of the selected driver, and the values given in figure 5 must be varied according to the recommendations for the driver. AC-Coupling A signal transformer or series capacitors can be used to make an AC-coupled input network. Figure 6 shows a recommended configuration using a transformer. Figure 6: Transformer coupled input Figure 4: Input configuration DC-Coupling Figure 5 shows a recommended configuration for DCcoupling. Note that the common mode input voltage must be controlled according to specified values. Preferably, the CM_EXT output should be used as reference to set the common mode voltage. Figure 5: DC coupled input with buffer 0-9 The input amplifier could be inside a companion chip or it could be a dedicated amplifier. Several suitable single ended to differential driver amplifiers exist in the market. The system designer should make sure the specifications of the selected amplifier is adequate for the total system, and that driving capabilities comply with the HMCAD1050-40 input specifications. Make sure that a transformer with sufficient linearity is selected, and that the bandwidth of the transformer is appropriate. The bandwidth should exceed the sampling rate of the ADC with at least a factor of 10. It is also important to minimize phase mismatch between the differential ADC inputs for good HD2 performance. This type of transformer coupled input is the preferred configuration for high frequency signals as most differential amplifiers do not have adequate performance at high frequencies. Magnetic coupling between the transformers and PCB traces may impact channel crosstalk, and must hence be taken into account during PCB layout. If the input signal is traveling a long physical distance from the signal source to the transformer (for example a long cable), kick-backs from the ADC will also travel along this distance. If these kickbacks are not terminated properly at the source side, they are reflected and will add to the input signal at the ADC input. This could reduce the ADC performance. To avoid this effect, the source must effectively terminate the ADC kick-backs, or the traveling distance should be very short. If this problem could not be avoided, the circuit in figure 8 can be used. Figure 7 shows AC-coupling using capacitors. Resistors from the CM_EXT output, RCM, should be used to bias the differential input signals to the correct volt- Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter age. The series capacitor, CI, form the high-pass pole with these resistors, and the values must therefore be determined based on the requirement to the high-pass cut-off frequency. ential clock sources as LVDS, LVPECL or differential sine wave can be connected directly to the input pins. For CMOS inputs, the CKN pin should be connected to ground, and the CMOS clock signal should be connected to CKP. For differential sine wave clock, the input amplitude must be at least ± 800 mVpp. The quality of the input clock is extremely important for high-speed, high-resolution ADCs. The contribution to SNR from clock jitter with a full scale signal at a given frequency is shown in equation 1, Note that startup time from Sleep Mode and Power Down Mode will be affected by this filter as the time required to charge the series capacitors is dependent on the filter cut-off frequency. If the input signal has a long traveling distance, and the kick-backs from the ADC not are effectively terminated at the signal source, the input network of figure 8 can be used. The configuration in figure 8 is designed to attenuate the kickback from the ADC and to provide an input impedance that looks as resistive as possible for frequencies below Nyquist. Values of the series inductor will however depend on board design and conversion rate. In some instances a shunt capacitor in parallel with the termination resistor (e.g. 33pF) may improve ADC performance further. This capacitor attenuate the ADC kick-back even more, and minimize the kicks traveling towards the source. However, the impedance match seen into the transformer becomes worse. (1) where fIN is the signal frequency, and εt is the total rms jitter measured in seconds. The rms jitter is the total of all jitter sources including the clock generation circuitry, clock distribution and internal ADC circuitry. For applications where jitter may limit the obtainable performance, it is of utmost importance to limit the clock jitter. This can be obtained by using precise and stable clock references (e.g. crystal oscillators with good jitter specifications) and make sure the clock distribution is well controlled. It might be advantageous to use analog power and ground planes to ensure low noise on the supplies to all circuitry in the clock distribution. It is of utmost importance to avoid crosstalk between the ADC output bits and the clock and between the analog input signal and the clock since such crosstalk often results in harmonic distortion. The jitter performance is improved with reduced rise and fall times of the input clock. Hence, optimum jitter performance is obtained with LVDS or LVPECL clock with fast edges. CMOS and sine wave clock inputs will result in slightly degraded jitter performance. If the clock is generated by other circuitry, it should be re-timed with a low jitter master clock as the last operation before it is applied to the ADC clock input. 0 A / D Converters - SMT SNRjitter = 20 · log (2 · π · ƒIN · єt) Figure 7: AC coupled input Digital Outputs Figure 8: Alternative input network Clock Input and Jitter considerations Typically high-speed ADCs use both clock edges to generate internal timing signals. In the HMCAD105040 only the rising edge of the clock is used. Hence, input clock duty cycles between 20% and 80% are acceptable. The input clock can be supplied in a variety of formats. The clock pins are AC-coupled internally. Hence a wide common mode voltage range is accepted. Differ- Digital output data are presented on parallel CMOS form. The voltage on the OVDD pin set the levels of the CMOS outputs. The output drivers are dimensioned to drive a wide range of loads for OVDD above 2.25V, but it is recommended to minimize the load to ensure as low transient switching currents and resulting noise as possible. In applications with a large fanout or large capacitive loads, it is recommended to add external buffers located close to the ADC chip. The timing is described in the Timing Diagram section. Note that the load or equivalent delay on CK_EXT Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com 0 - 10 HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter A / D Converters - SMT 0 always should be lower than the load on data outputs to ensure sufficient timing margins. are set, the code is forced to all ones for overrange and all zeros for underrange. The digital outputs can be set in tristate mode by setting the OE_N signal high. Note that the out of range flags (ORNG) will behave differently for 12 bit and 13 bit output. For 13 bit output ORNG will be set when digital output data are all ones or all zeros. For 12-bit output the ORNG flags will be set when all twelve bits are zeros or ones and when the thirteenth bit is equal to the rest of the bits. The HMCAD1050-40 employs digital offset correction. This means that the output code will be 4096 with shorted inputs. However, small mismatches in parasitics at the input can cause this to alter slightly. The offset correction also results in possible loss of codes at the edges of the full scale range. With no offset correction, the ADC would clip in one end before the other, in practice resulting in code loss at the opposite end. With the output being centered digitally, the output will clip, and the out of range flags will be set, before max code is reached. When out of range flags The output data are presented on offset binary form when DFRMT is low (connect to OVSS). Setting DFRMT high (connect to OVDD) results in 2’s complement output format. Details are shown in table 3. Table 3: Data Format Description for 2Vpp Full Scale Range Differential Input Voltage (IPx - INx) Output Data: Dx_12 : Dx_0 (DFRMT = 0, Offset Binary) Output Data: Dx_12 : Dx_0 (DFRMT = 1, 2’s Complement) 1.0 V 1 1111 1111 1111 0 1111 1111 1111 +0.24mV 1 0000 0000 0000 0 0000 0000 0000 -0.24mV 0 1111 1111 1111 1 1111 1111 1111 -1.0V 0 0000 0000 0000 1 0000 0000 0000 The data outputs can be used in three different configurations. • Normal Mode: All 13 bits are used. MSB is Dx_12 and LSB is Dx_0. This mode gives optimum performance • 12-bit Mode: Reference Voltages The reference voltages are internally generated and buffered based on a bandgap voltage reference. No external decoupling is necessary, and the reference voltages are not available externally. This simplifies usage of the ADC since two extremely sensitive pins, otherwise needed, are removed from the interface. The LSB is left unconnected such that only 12 bits are used. MSB is Dx_12 and LSB is Dx_1. This mode gives slightly reduced performance due to increased quantization noise. If a lower full scale range is required the 13-bit output word provides sufficient resolution to perform digital scaling with an equivalent impact on noise compared to adjusting the reference voltages. • Reduced Full Scale Range Mode: A simple way to obtain 1.0Vpp input range with a 12-bit output word is shown in table 4. Note that only 2’s complement output data are available in this mode and that out of range conditions must be determined based on a two bit output. The output code will wrap around when the code goes outside the full scale range. The out of range bits should be used to clamp the output data for overrange conditions. The full scale range is reduced from 2 Vpp to 1 Vpp which is equivalent to 6 dB gain in the ADC frontend. Note that data are only available in 2’s complement format in this mode. MSB is Dx_11 and LSB is Dx_0. Note that the codes will wrap around when exceeding the full scale range, and that out of range bits should be used to clamp output data. See section Reference Voltages for details. This mode gives slightly reduced performance 0 - 11 Data Format Selection Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Table 4: Data Format Description for 1Vpp Full Scale Range Out of Range (Use Logical and Function for &) > 0.5V 0111 1111 1111 Dx_12 = 1 & Dx_11 = 1 0.5V 0111 1111 1111 0111 1111 1111 +0.24mV 0000 0000 0000 0000 0000 0000 -0.24mV 1111 1111 1111 1111 1111 1111 -0.5V 1000 0000 0000 1000 0000 0000 < -0.5V 1000 0000 0000 Dx_12 = 0 & Dx_11 = 0 Output Data Dx_11:Dx_0 (DFRMT = 1) (2’s Complement) Out of Range (Use Logical and Function for &) 0111 1111 1111 D_12 = 0 & D_11 = 1 1000 0000 0000 Dx_12 = 1 & Dx_11 = 0 Operational Modes Startup Initialization The operational modes are controlled with the PD_N and SLP_N pins. If PD_N is set low, all other control pins are overridden and the chip is set in Power Down mode. In this mode all circuitry is completely turned off and the internal clock is disabled. Hence, only leakage current contributes to the Power Down Dissipation. The startup time from this mode is longer than for other idle modes as all references need to settle to their final values before normal operation can resume. The HMCAD1050-40 must be reset prior to normal operation. This is required every time the power supply voltage has been switched off. A reset is performed by applying Power Down mode. Wait until a stable supply voltage has been reached, and pull the PD_N pin for the duration of at least one clock cycle. The input clock must be running continuously during this Power Down period and until active operation is reached. Alternatively the PD pin can be kept low during power-up, and then be set high when the power supply voltage is stable. The SLP_N bus can be used to power down each channel independently, or to set the full chip in Sleep Mode. In This mode internal clocking is disabled, but some low bandwidth circuitry is kept on to allow for a short startup time. However, Sleep Mode represents a significant reduction in supply current, and it can be used to save power even for short idle periods. The input clock should be kept running in all idle modes. However, even lower power dissipation is possible in Power Down mode if the input clock is stopped. In this case it is important to start the input clock prior to enabling active mode. Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com 0 A / D Converters - SMT Output data Dx_11:Dx_0 (DFRMT = 0) (2’s Complement) Differential Input Voltage (IPx - INx) 0 - 12 HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Outline Drawing A / D Converters - SMT 0 Table 6: 9x9 mm QFN (64 Pin LP9) Dimensions Symbol Millimeter Min A A1 Inch Max 0.01 0.05 A2 0.65 0.7 A3 0.2 REF b Min Typ 0.9 0 0.2 D 0.25 Max 0.035 0 0.000 0.002 0.026 0.028 0.008 REF 0.3 0.008 9.00 bsc D1 0.01 0.012 0.354 bsc 8.75 bsc 0.344 bsc D2 3.79 3.99 4.19 0.149 0.157 0.165 L 0.3 0.4 0.5 0.012 0.016 0.02 e 0 - 13 Typ 0.50 bsc Θ1 0° F 1.9 G 0.24 0.020 bsc 12° 0° 12° 0.075 0.42 0.6 0.010 0.017 0.024 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com HMCAD1050-40 v01.0411 Dual 13/12-Bit 20/40 MSPS A/D Converter Package Information Part Number Package Body Material Lead Finish MSL [1] Package Marking [2] HMCAD1050-40 RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn Level 2A ASD0500 XXXX XXXX [1] MSL, Peak Temp: The moisture sensitivity level rating classified according to the JEDEC industry standard and to peak solder temperature. [2] Proprietary marking XXXX, 4-Digit lot number XXXX A / D Converters - SMT 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery and to place orders: Microwave Corporation, Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of theirApplication respective owners. Support: apps@hittite.com 0 - 14