Design
Resources
Tools
and Models
Support
Click here to ask an associate for production status of specific part numbers.
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
General Description
The LM75 temperature sensor includes a delta-sigma
analog-to-digital converter, and a digital overtemperature
detector. The host can query the LM75 through its I2C
interface to read temperature at any time. The open-drain
overtemperature output (OS) sinks current when the
programmable temperature limit is exceeded. The OS
output operates in either of two modes, comparator or
interrupt. The host controls the temperature at which the
alarm is asserted (TOS) and the hysteresis temperature
below which the alarm condition is not valid (THYST). Also,
the LM75’s TOS and THYST registers can be read by the
host. The address of the LM75 is set with three pins to allow
multiple devices to work on the same bus. Power-up is in
comparator mode, with defaults of TOS = +80°C and THYST
= +75°C. The 3.0V to 5.5V supply voltage range, low supply
current, and I2C interface make the LM75 ideal for many
applications in thermal management and protection.
● ISO (SOP) and μMAX® (μSOP) Packages
● I2C Bus Interface
● Separate Open-Drain OS Output Operates as
Interrupt or Comparator/Thermostat Input
● Register Readback Capability
● Power-Up Defaults Permit Stand-Alone Operation
as a Thermostat
● 3.0V to 5.5V Supply Voltage
● Low Operating Supply Current 250μA (typ), 1mA (max)
● 4μA (typ) Shutdown Mode Minimizes Power
Consumption
● Up to Eight LM75s Can Be Connected to a Single Bus
● Pin- and/or Register-Compatible with ImprovedPerformance Maxim Sensors Including MAX7500,
MAX6625, MAX6626, DS75LV, and DS7505
Functional Diagram
Applications
●
●
●
●
Features
Thermal System Management
Thermal Protection
Test Equipment
Computers and Office Electronics
+VS = 3.0V to 5.5V
8
9-BIT DELTASIGMA ADC
TOS SET POINT
REGISTER
Pin Configuration
SDA
1
SCL
2
OS
3
GND
4
POINTER
REGISTER
CONFIGURATION
REGISTER
+
LM75
8
+VS
7
A0
6
A1
5
A2
OS
SET POINT
COMPARATOR W/
HYSTERESIS
16
μMAX is a registered trademark of Maxim Integrated Products, Inc.
TOP VIEW
3
16
SILICON
BANDGAP
TEMPERATURE
SENSOR
8
16
8
THYST SET
POINT REGISTER
16
16
1
7
A0
6
A1
5
A2
2-WIRE INTERFACE
2
SDA
SCL
4
µMAX (µSOP), SO
Ordering Information/Selector Guide
PART
LM75BIM-3+
LM75BIMX-3+
LM75BIMM-3+
LM75BIMMX-3+
LM75BIM-5+
LM75BIMX-5+
LM75BIMM-5+
LM75BIMMX-5+
PIN-PACKAGE
8 SO (SOP)
8 SO (SOP)
8 µMAX (µSOP)
8 µMAX (µSOP)
8 SO (SOP)
8 SO (SOP)
8 µMAX (µSOP)
8 µMAX (FSOP)
PKG
Bulk
T&R
Bulk
T&R
Bulk
T&R
Bulk
T&R
SUPPLY VOLTAGE (V)
3.3
3.3
3.3
3.3
5.0
5.0
5.0
5.0
Note: Devices are specified over the -55°C to +125°C temperature range and include I2C noise filter.
+Denotes a lead(Pb)-free/RoHS-compliant package.
T&R = Tape and reel.
TOP MARK
LM75BAIM-3
LM75BAIM-3
T01B
T01B
LM75BIM-5
LM75BIM-5
T00B
T00B
19-4385; Rev 2; 11/21
© 2021 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
One Analog Way, Wilmington, MA 01887 U.S.A.
|
Tel: 781.329.4700
|
© 2021 Analog Devices, Inc. All rights reserved.
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Absolute Maximum Ratings (Note 1)
+VS to GND...........................................................-0.3V to +6.0V
OS, SDA, SCL to GND..........................................-0.3V to +6.0V
All Other Pins to GND................................-0.3V to (+VS + 0.3V)
Input Current at Any Pin (Note 2)..........................................5mA
Package Input Current (Note 2)..........................................20mA
OS Output Sink Current......................................................10mA
Continuous Power Dissipation (TA = +70°C) (Note 3)
8-Pin μMAX (μSOP)
(derate 4.5mW/°C above +70°C)..................................362mW
8-Pin SO (SOP) (derate 5.9mW/°C above +70°C) ........471mW
Junction-to-Case Thermal Resistance (θJC) (Note 3)
8-Pin μMAX (μSOP).....................................................42°C/W
8-Pin SO (SOP)............................................................40°C/W
Junction-to-Ambient Thermal Resistance (θJA) (Note 3)
8-Pin μMAX (μSOP)...................................................221°C/W
8-Pin SO (SOP)..........................................................170°C/W
ESD Protection
Human Body Model (RD = 1.5kΩ, CS = 100pF)
All Pins to GND................................................................±2kV
Operating Temperature Range.......................... -55°C to +125°C
Junction Temperature.......................................................+150°C
Storage Temperature Range............................. -65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications
do not apply when operating the device beyond its rated operating conditions.
Note 2: When the input voltage (VI) at any pin exceeds the Absolute Maximum Ratings limits (VI < GND, VI > 6V or VI > +VS), the
current at that pin should be limited to 5mA. The 20mA maximum package input current rating limits the number of pins that
can safely exceed the power supplies with an input current of 5mA to four.
Note 3: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a single-layer
board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(+VS = +3.0V to +5.5V, unless otherwise noted. Temperature accuracy specifications apply for +VS = 3.3V for versions with “-3” in
the suffix and for +VS = 5V for versions with “-5” in the suffix. TA = -55°C to +125°C, unless otherwise noted. Typical values are at
+VS = +5V, TA = +25°C.) (Notes 4, 5)
PARAMETER
SYMBOL
Accuracy (Six-Sigma)
Accuracy (Three-Sigma) (Note 6)
CONDITIONS
MIN
MAX
-2.0
+2.0
-55°C ≤ TA ≤ +125°C
-3.0
+3.0
-25°C ≤ TA ≤ +100°C
-1.5
+1.5
-55°C ≤ TA ≤ +125°C
-2.0
+2.0
Resolution
9
Temperature Conversion Time
Quiescent Supply Current
°C
°C
Bits
100
300
ms
I2C inactive
0.25
0.5
mA
Shutdown mode, +VS = 3V
4
Shutdown mode, +VS = 5V
6
3.0
OS Output Saturation Voltage
IOUT = 4.0mA (Note 8)
OS Delay
(Note 9)
tOF
UNITS
(Note 7)
+VS Supply Voltage Range
OS Output Fall Time
TYP
-25°C ≤ TA ≤ +100°C
1
CL = 400pF, IO = 3mA (Note 10)
µA
5.5
V
0.8
V
6
Conversions
250
ns
TOS Default Temperature
(Note 11)
80
°C
THYST Default Temperature
(Note 11)
75
°C
www.analog.com
Analog Devices │ 2
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Electrical Characteristics (continued)
(+VS = +3.0V to +5.5V, unless otherwise noted. Temperature accuracy specifications apply for +VS = 3.3V for versions with “-3” in
the suffix and for +VS = 5V for versions with “-5” in the suffix. TA = -55°C to +125°C, unless otherwise noted. Typical values are at
+VS = +5V, TA = +25°C.) (Notes 4, 5)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
LOGIC (SDA, SCL, A0, A1, A2)
Input High Voltage
VIH
+VS x
0.7
+VS +
0.5
V
Input Low Voltage
VIL
-0.3
+VS x
0.3
V
Input High Current
IIH
VIN = 5V
1.0
µA
Input Low Current
IIL
VIN = 0V
Input Capacitance
CIN
0.005
-1.0
All digital inputs
-0.005
µA
20
pF
Output High Current
VOH = 5V
10
µA
Output Low Voltage
IOL = 3mA
0.4
V
I2C-COMPATIBLE TIMING (Notes 12, 13)
(Clock) SCL Period
tSCL
Bus timeout inactive
2.5
µs
Data In Setup Time to SCL High
tSU:DAT
10% of SDA to 10% of SCL
100
ns
Data Out Stable After SCL Low
tHD:DAT
10% of SCL to 10% of SDA
0
µs
Start Condition Setup Time
(SDA Low to SCL Low)
tSU:STA
90% of SCL to 90% of SDA
100
ns
STOP Condition Hold Time
tHD:STO
100
ns
SDA Time Low for Reset of Serial
Interface
tTIMEOUT
(Note 14)
75
325
ms
Note 4: All parts operate properly over the 3V to 5.5V supply voltage range. The devices are tested and specified for rated
accuracy at their nominal supply voltage.
Note 5: All parameters are measured at TA = +25°C. Values over the temperature range are guaranteed by design.
Note 6: There is no industry-wide standard for temperature accuracy specifications. Maxim’s standard is six-sigma. The threesigma specification is included to allow easier comparison to products built by manufacturers who use different standards.
Note 7: This specification indicates how often temperature data is updated. The devices can be read at any time without regard to
conversion state, while yielding the last conversion result.
Note 8: For best accuracy, minimize output loading. Higher sink currents can affect sensor accuracy due to internal heating.
Note 9: OS delay is user programmable up to 6 over-limit conversions before OS is set to minimize false tripping in noisy
environments.
Note 10: Guaranteed by design.
Note 11: Default values set at power-up.
Note 12: All timing specifications are guaranteed by design.
Note 13: Unless otherwise noted, these specifications apply for +VS = +5VDC for LM75BIM-5 and LM75BIMM-5 and +VS = +3.3VDC
for LM75BIM-3 and LM75BIMM-3. CL (load capacitance) on output lines = 80pF, unless otherwise specified.
The switching characteristics of the LM75 fully meet or exceed the published specifications of the I2C bus.
These parameters are the timing relationships between SCL and SDA signals related to the LM75. They are not I2C bus
specifications.
Note 14: Holding the SDA line low for a time greater than tTIMEOUT causes the device to reset SDA to the IDLE state of the serial
bus communication (SDA set high).
www.analog.com
Analog Devices │ 3
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
280
+VS = +5V
270
260
+VS = +3V
250
240
230
-55
-25
5
35
65
95
TEMPERATURE (°C)
125
5
4 TYPICAL PARTS
1.0
+VS = +5V
4
1.5
ACCURACY vs. TEMPERATURE
LM75 toc03
2.0
LM75 toc02
290
6
SHUTDOWN SUPPLY CURRENT (µA)
LM75 toc01
QUIESCENT SUPPLY CURRENT (µA)
300
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
ACCURACY (°C)
QUIESCENT SUPPLY CURRENT
vs. TEMPERATURE
3
+VS = +3V
2
0.5
0
-0.5
-1.0
1
0
-1.5
-55
-25
5
35
65
95
125
-2.0
-55
-25
TEMPERATURE (°C)
5
35
65
95
125
TEMPERATURE (°C)
Pin Description
PIN
NAME
FUNCTION
1
SDA
Serial-Data Input/Output Line. Open drain. Connect SDA to a pullup resistor.
2
SCL
Serial Clock Input. Open drain. Connect SCL to a pullup resistor.
Overtemperature Shutdown Output. Open drain. Connect OS to a pullup resistor.
3
OS
4
GND
5
A2
2-Wire Interface Address Input. Connect A2 to GND or +VS to set the desired I2C bus address.
Do not leave unconnected (see Table 1).
6
A1
2-Wire Interface Address Input. Connect A1 to GND or +VS to set the desired I2C bus address.
Do not leave unconnected (see Table 1).
7
A0
2-Wire Interface Address Input. Connect A0 to GND or +VS to set the desired I2C bus address.
Do not leave unconnected (see Table 1).
8
+VS
www.analog.com
Ground
Positive Supply Voltage Input. Bypass to GND with a 0.1µF bypass capacitor.
Analog Devices │ 4
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Detailed Description
Power-Up and Power-Down
The LM75 temperature sensor measures temperature
and converts the data into digital form using a bandgap
type temperature sensor and a 9-bit delta-sigma ADC.
An I2C-compatible 2-wire serial interface allows access
to conversion results. The LM75 accepts standard I2C
commands to read the data, set the overtemperature
alarm (OS) trip thresholds, and configure other characteristics. While reading the Temperature register, any
changes in temperature are ignored until the read is
completed. The Temperature register is updated for the
new temperature measurement upon completion of the
read operation.
OS Output, TOS, and THYST Limits
In comparator mode (see Figure 1), the open-drain OS
output asserts when the temperature rises above the limit
programmed into the TOS register, and becomes high
impedance when the temperature falls below the limit set
in the THYST register. In this mode the LM75 operates
as a thermostat, and the OS output can be used to take
action to reduce the temperature (e.g., turn on a cooling
fan, reduce clock speed, or shut down the system).
In interrupt mode, exceeding TOS also asserts OS. OS
remains asserted until a read operation is performed on
any of the registers. Once OS has asserted due to crossing above TOS and is then reset, it is asserted again only
when the temperature drops below THYST. The output
then remains asserted until it is reset by a read. It is then
asserted again if the temperature rises above TOS, and so
on. Putting the LM75 into shutdown mode also resets OS.
The LM75 powers up to a known state, as indicated
in Table 2. Some of these settings are summarized as
following:
● Comparator mode
● TOS = +80°C
● THYST = +75°C
● OS active low
● Command byte pointer = 0x00
I2C-Compatible Bus Interface
From a software perspective, the LM75 appears as a
set of byte-wide registers that contain temperature data,
alarm threshold values, and control bits. A standard I2Ccompatible, 2-wire serial interface reads temperature data
and writes control bits and alarm threshold data. Each
device responds to its own I2C slave address, which is
selected using A0, A1, and A2. See Table 1.
TOS
TEMPERATURE
THYST
OS OUTPUT
(COMPARATOR MODE)
OS SET ACTIVE LOW
OS OUTPUT
(INTERRUPT MODE)
OS SET ACTIVE LOW
READ
OPERATION
READ
OPERATION
READ
OPERATION
Figure 1. OS Output Temperature Response Diagram
Table 1. Slave Address
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
1
0
0
1
A2
A1
A0
R/W
Table 2. Register Functions
ADDRESS
(hex)
POR STATE
(hex)
POR STATE (binary)
POR STATE (°C)
READ/
WRITE
Temperature
00
000X
0000 0000 0XXX XXXX
—
Read only
Configuration
01
00
0000 0000
—
R/W
THYST
02
4B0X
0100 1011 0XXX XXXX
75
R/W
TOS
03
500X
0101 0000 0XXX XXXX
80
R/W
REGISTER NAME
X = Don’t care.
www.analog.com
Analog Devices │ 5
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
SDA
tSU:DAT
tSU:STA
tHD:DAT
tLOW
tBUF
tSU:STO
tHD:STA
SCL
tHIGH
tHD:STA
tR
tF
START
CONDITION
(S)
REPEATED START
CONDITION
(SR)
ACKNOWLEDGE
(A)
STOP
CONDITION
(P)
START
CONDITION
(S)
PARAMETERS ARE MEASURED FROM 10% TO 90%.
Figure 2. Serial Bus Timing
Table 3. Temperature, THYST, and TOS Register Definition
UPPER BYTE
D15
Sign bit
1= Negative
0 = Positive
LOWER BYTE
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
MSB
64°C
32°C
16°C
8°C
4°C
2°C
1°C
LSB
0.5°C
X
X
X
X
X
X
X
X = Don’t care.
Table 4. Temperature Data Output Format
DIGITAL OUTPUT
0111 1101 0
BINARY
HEX
+125
0111 1101 0XXX XXXX
7D0X
+25
0001 1001 0XXX XXXX
190X
+0.5
0000 0000 1XXX XXXX
008X
0
0000 0000 0XXX XXXX
000X
-0.5
1111 1111 1XXX XXXX
FF8X
-25
1110 0111 0XXX XXXX
E70X
-55
1100 1001 0XXX XXXX
C90X
X = Don’t care.
BINARY OUTPUT CODE (9MSB)
TEMPERATURE (°C)
0001 1001 0
0000 0000 1
0000 0000 0
1111 1111 1
1110 0111 0
1100 1001 0
-55
-25
-0.5
0 +0.5
LOCAL
+25
+125
Figure 3. Temperature-to-Digital Transfer Function
www.analog.com
Analog Devices │ 6
www.analog.com
START
BY
MASTER
START
BY
MASTER
START
BY
MASTER
ADDRESS
BYTE
REPEAT
START
BY
MASTER
ADDRESS BYTE
ADDRESS
BYTE
MOST SIGNIFICANT
DATA BYTE
ACK BY
MASTER
LEAST SIGNIFICANT
DATA BYTE
ACK BY
LM75
POINTER BYTE
MOST SIGNIFICANT
DATA BYTE
ACK BY
LM75
ACK BY
MASTER
DATA
BYTE
NO
ACK BY
MASTER
(c) TYPICAL 1-BYTE READ FROM CONFIGURATION REGISTER WITH PRESET POINTER.
ACK BY
LM75
STOP
COND BY
MASTER
(b) TYPICAL POINTER SET FOLLOWED BY IMMEDIATE READ FOR 2-BYTE REGISTER SUCH AS TEMP, T HIGH, TLOW .
ADDRESS
BYTE
ACK BY
MASTER
(a) TYPICAL 2-BYTE READ FROM PRESET POINTER LOCATION SUCH AS TEMP, THIGH , TLOW .
ACK BY
LM75
LEAST SIGNIFICANT
DATA BYTE
NO ACK BY
MASTER
NO
ACK BY
MASTER
STOP
COND BY
MASTER
STOP
COND BY
MASTER
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Figure 4. I2C-Compatible Timing Diagram (Read)
Analog Devices │ 7
www.analog.com
START
BY
MASTER
START
BY
MASTER
START
BY
MASTER
ADDRESS
BYTE
ADDRESS
BYTE
ADDRESS
BYTE
ACK BY
LM75
ACK BY
LM75
ACK BY
LM75
ACK BY
LM75
REPEAT
START
BY
MASTER
ADDRESS
BYTE
ACK BY
LM75
POINTER
BYTE
POINTER
BYTE
CONFIGURATION
BYTE
MOST SIGNIFICANT
DATA BYTE
(c) THIGH AND TLOW WRITE
ACK BY
LM75
(b) CONFIGURATION REGISTER WRITE
ACK BY
LM75
ACK BY
LM75
ACK BY
LM75
STOP
COND BY
MASTER
(a) TYPICAL POINTER SET FOLLOWED BY IMMEDIATE READ FROM CONFIGURATION REGISTER
POINTER
BYTE
LEAST SIGNIFICANT
DATA BYTE
DATA
BYTE
ACK BY
LM75
STOP
COND BY
MASTER
STOP
COND BY
MASTER
NO
ACK BY
MASTER
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Figure 5. I2C-Compatible Timing Diagram (Write)
Analog Devices │ 8
LM75
Temperature Data Format
Temperature data is stored in the Temperature, TOS Set
Point, and THYST Set Point registers. The temperature
data format is 9 bits, two’s complement, and the register
is read out in 2 bytes: an upper byte and a lower byte.
Bits D15–D7 contain the temperature data, with the LSB
representing 0.5°C and the MSB representing the sign bit
(see Table 3). The MSB is transmitted first. The last 7 bits
of the lower byte, bits D6–D0, are don’t cares.
Shutdown
Set bit D0 in the Configuration register to 1 to place
the LM75 in shutdown mode and reduce supply current
to 4μA. In interrupt mode, entering shutdown resets
the OS output. While in shutdown, the I2C remains
active and TOS and THYST limit registers along with the
Configuration register remain accessible to the master.
Fault Queue
The fault queue prevents OS false tripping in noisy
environments. The number of faults set in the queue
(up to 6) must occur to trip the OS output.
Comparator/Interrupt Mode
The events that trigger OS are identical between comparator and interrupt modes. In comparator mode, OS
is asserted when the temperature rises above the TOS
value. OS is deasserted when the temperature drops
below the THYST value. In interrupt mode, OS is asserted
when the temperature rises above the TOS value or falls
below the THYST value. OS is deasserted only after
performing a read operation.
OS Output
The OS output is an open-drain output without an internal
pullup. Connect a pullup resistor from OS to +VS. Using
larger resistance values reduces any temperature errors
due to self heating from current entering OS.
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Write to the Configuration register by writing an address
byte, a data pointer byte, and a data byte. If 2 data bytes
are written, the second data byte overrides the first. The
TOS and THYST registers require 1 address byte, 1 pointer byte, and 2 data bytes. If only 1 data byte is written, it
is saved in bits D15–D8 of the respective register. If more
than 2 data bytes are written, only the first 2 bytes are
recognized while the remaining bytes are ignored.
Read from the LM75 in one of two ways. If the location
latched in the Pointer register is set from the previous
read, the new read consists of an address byte, followed
by retrieving the corresponding number of data bytes. If
the Pointer register needs to be set to a new address,
perform a read operation by writing an address byte,
pointer byte, repeat start, and another address byte.
An inadvertent 8-bit read from a 16-bit register, with the
D7 bit low, can cause the device to stop in a state where
the SDA line is held low. Ordinarily, this would prevent
any further bus communication until the master sends
nine additional clock cycles or SDA goes high. At that
time, a stop condition resets the device. If the additional
clock cycles are not generated by the master, the LM75
bus resets and unlocks after the bus timeout period has
elapsed.
+VS
A0
A1
A2/RESET
LM75
SDA
SMBus™
INTERFACE
BLOCK
SCL
DATA
Internal Registers
The LM75’s Pointer register selects between four data
registers (see Figure 6). At power-up, the pointer is
set to read the Temperature register at address 0x00.
The Pointer register latches the last location to which
it was set. All registers are read and write, except the
Temperature register, which is read only.
ADDRESS
POINTER REGISTER
(SELECTS REGISTER
FOR COMMUNICATION)
REGISTER SELECT
OS Polarity
The OS polarity can be programmed for active-low or
active-high operation. In active-low operation, OS goes
low when triggered by a temperature event.
OS
TEMPERATURE
(READ ONLY)
POINTER = 0000 0000
CONFIGURATION
(READ/WRITE)
POINTER = 0000 0001
TOS SET POINT
(READ/WRITE)
POINTER = 0000 0011
THYST SET POINT
(READ/WRITE)
POINTER = 0000 0010
GND
Figure 6. Block Diagram
SMBus is a trademark of Intel Corp.
www.analog.com
Analog Devices │ 9
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Table 5. Configuration Register Definition
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
Fault Queue
Fault Queue
OS Polarity
Comparator/
Interrupt
Shutdown
Configuration Register
The 8-bit Configuration register sets the fault queue, OS
polarity, shutdown control, and whether the OS output
functions in comparator or interrupt mode. When writing
to the Configuration register, set bits D7, D6, and D5 to
zero (see Table 5).
Bits D4 and D3, the fault queue bits, determine the
number of faults necessary to trigger an OS condition
(see Table 6). The number of faults set in the queue must
occur consecutively to trip the OS output. The fault queue
prevents OS false tripping in noisy environments.
Set bit D2, the OS polarity bit, to zero to force the OS
output polarity to active low. Set bit D2 to 1 to set the
OS output polarity to active high. OS is an open-drain
output under all conditions and requires a pullup resistor to
output a high voltage (see Figure 1).
Set bit D1, the comparator/interrupt bit to zero to operate OS in comparator mode. In comparator mode, OS
is asserted when the temperature rises above the TOS
value. OS is deasserted when the temperature drops
below the THYST value (see Figure 1). Set bit D1 to 1 to
operate OS in interrupt mode. OS is asserted in interrupt
mode when the temperature rises above the TOS value or
falls below the THYST value. OS is deasserted only after
performing a read operation.
Set bit D0, the shutdown bit, to zero for normal operation.
Set bit D0 to 1 to shutdown the LM75’s internal blocks.
The I2C interface remains active as long as the shutdown
bit is set. The TOS, THYST, and Configuration registers
can still be written to and read from while in shutdown.
Applications Information
LM75 measures the temperature of its own die. The
thermal path between the die and the outside world determines the accuracy of temperature measurements. Most
of the heat flows in to or out of the die through the leads.
www.analog.com
Table 6. Configuration Register Fault
Queue Bits
D4
D3
NUMBER OF FAULTS
0
0
1 (POR state)
0
1
2
1
0
4
1
1
6
Because of this, the LM75 most easily measures the PCB
temperature. For ambient temperature measurements,
mount the LM75 on a separate PCB away from high
power sources. Temperature errors due to self heating
of the LM75 die is minimal due to the low supply current.
Digital Noise Issues
The lowpass filters in the SCL and SDA digital lines mitigate the effects of bus noise, and make communications
in noisy environments more robust. Good layout practices
also help. Keep switching power supplies away from digital lines, and arrange for high-speed digital traces to cross
SCL and SDA at right angles. Properly terminate long
PCB traces and bus traces connected to multiple slaves.
Serial bus no-acknowledge (which causes unnecessary
bus traffic) is the most common symptom of excessive
noise coupling into the SDA and SCL lines. Noise with
amplitude greater than the LM75’s hysteresis (400mVP-P,
typ), overshoot greater than 300mV above +VS, and undershoot more than 300mV below GND may prevent successful serial communication.
Resistance can be added in series with the SDA and SCL
lines to help filter noise and ringing. A 5kΩ resistor placed
in series with the SCL line and as close as possible to the
SCL pin, with the 5pF to 10pF stray capacitance of the
device, provides a 6MHz to 12MHz lowpass filter, which
is sufficient filtering in many cases.
Analog Devices │ 10
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
3V to
5.5V
3V to
5.5V
R2
10kΩ
R3
10kΩ
R1
10kΩ
GND
or +V
SCL
A0
A1
A2
12V
+VS
OS
LM75
N-CHANNEL MOSFET
+Vs
SCL
SDA
SDA
12V 300mA
FAN MOTOR
R2
10kΩ
R3
10kΩ
LM75
OS
GND
TO
Microcontroller
GND
OS
Figure 7. I2C Controlled Temperature Sensor
3V to
5.5V
C1
0.1µF
Figure 8. Fan Control
SHDN
OUT-
BIAS
GND
MAX4364
IN+
R1
10kΩ
OUT+
INC2
0.1µF
+Vs
OS
R5
200kΩ
C4
6.8nF
C3
6.8nF
LM75
GND
VCC
R2
10kΩ
R3
10kΩ
C5
6.8nF
R4
10kΩ
Figure 9. Temperature Sensor with Audible Alarm
www.analog.com
Analog Devices │ 11
LM75
Chip Information
PROCESS: CMOS
www.analog.com
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
8 SO (SOP)
S8-2
21-0041
8 μMAX (μSOP)
U8-1
21-0036
Analog Devices │ 12
LM75
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
Revision History
REVISION
NUMBER
REVISION
DATE
0
3/09
Initial release
—
1
11/21
Updated Ordering Information table
1
2
11/21
Updated Ordering Information table
1
DESCRIPTION
PAGES
CHANGED
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is
assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that
may result from its use.Specifications subject to change without notice. No license is granted by implicationor
otherwise under any patent or patent rights of Analog Devices. Trademarks andregistered trademarks are the
property of their respective owners.
w w w . a n a l o g . c o m
Analog Devices │ 13
工商网监
湘ICP备2023018690号
