LT1033
3A Negative Adjustable
Regulator
Features
Description
Guaranteed 1% Initial Voltage Tolerance
nn Guaranteed 0.015%/V Line Regulation
nn Guaranteed 0.02%/ W Thermal Regulation
The LT®1033 negative adjustable regulator will deliver
up to 3A output current over an output voltage range of
–1.2V to –32V. Linear Technology has made significant
improvements in these regulators compared to previous
devices, such as better line and load regulation, and a
maximum output voltage error of 1%.
nn
Preconditioning
nn
The LT1033 is easy to use and difficult to damage. Internal
current and power limiting as well as true thermal limiting
prevents device damage due to overloads or shorts, even
if the regulator is not fastened to a heat sink.
100% Thermal Limit Burn-In
Applications
Maximum reliability is attained with Linear Technology’s
advanced processing techniques combined with a 100%
burn-in in the thermal limit mode. This assures that all
device protection circuits are working and eliminates field
failures experienced with other regulators that receive only
standard electrical testing.
Adjustable Power Supplies
System Power Supplies
nn Precision Voltage/Current Regulators
nn On-Card Regulators
nn
nn
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
Ultrafast and ThinSOT are trademarks of Linear Technology Corporation. All other trademarks
are the property of their respective owners.
Typical Application
Negative 5V Regulator
Current Limit
6
2µF
TANT
R1
100Ω
ADJ
–VIN
IN
OUT
LT1033
+
5
2µF
TANT
–5V, 3A
1033 TA01a
OUTPUT CURRENT (A)
+
R2
301Ω
4
3
2
1
0
0
5
10
15
20
25
30
INPUT-OUTPUT DIFFERENTIAL (V)
35
1033 TA01b
1033fd
For more information www.linear.com/LT1033
1
LT1033
Absolute Maximum Ratings
(Note 1)
Power Dissipation................................ Internally Limited
Input to Output Voltage Differential...........................35V
Operating Junction Temperature Range
LT1033M (OBSOLETE) ...................... –55°C to 150°C
LT1033C................................................. 0°C to 125°C
Storage Temperature Range
LT1033M (OBSOLETE) ...................... –65°C to 150°C
LT1033C............................................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec.)................... 300°C
Pin Configuration
BOTTOM VIEW
1
FRONT VIEW
FRONT VIEW
2
ADJ VOUT
CASE IS
VIN
K PACKAGE
4-LEAD TO-3 METAL CAN
TJMAX = 150°C, θJA = 35°C/W(MK)
TJMAX = 125°C, θJA = 35°C/W(CK)
VOUT
VOUT
VIN
VIN
ADJ
ADJ
CASE IS VIN
T PACKAGE
3-LEAD PLASTIC TO-220
TJMAX = 125°C, θJA = 50°C/W
OBSOLETE PACKAGE
CASE IS VIN
P PACKAGE
3-LEAD PLASTIC TO-3P
TJMAX = 125°C, θJA = 35°C/W
OBSOLETE PACKAGE
Consider the T Package for Alternate Source
Consider the T Package for Alternate Source
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT1033CT#PBF
NA
LT1033CT
3-Lead Plastic TO-220
0°C to 125°C
LT1033CP#PBF
NA
LT1033CP
3-Lead Plastic TO-3P
0°C to 125°C
OBSOLETE PACKAGE
LEAD BASED FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT1033CT
NA
LT1033CT
3-Lead Plastic TO-220
0°C to 125°C
LT1033CP
NA
LT1033CP
3-Lead Plastic TO-3P
0°C to 125°C
LT1033CK
NA
LT1033CK
2-Lead TO-3 Metal Can
0°C to 125°C
LT1033MK
NA
LT1033MK
2-Lead TO-3 Metal Can
–55°C to 125°C
OBSOLETE PACKAGE
Consult LTC Marketing for parts specified with wider operating temperature ranges.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
1033fd
2
For more information www.linear.com/LT1033
LT1033
Electrical Characteristics
(Note 2) The l denotes the specifications which apply over the full
operating temperature range, otherwise specifications are at TA = 25°C.
LT1033M
SYMBOL PARAMETER
VREF
Reference Voltage
CONDITIONS
MIN
|VIN – VOUT| = 5V, IOUT = 5mA,
TJ = 25°C
3V ≤ |VIN – VOUT| ≤ 35V
5mA ≤ IOUT ≤ IMAX, P ≤ PMAX
∆VOUT
∆IOUT
∆VOUT
∆VIN
Load Regulation
Line Regulation
Ripple Rejection
Thermal Regulation
10mA ≤ IOUT ≤ IMAX, (Note 3)
TJ = 25°C, |VOUT| ≤ 5V
TJ = 25°C, |VOUT| ≥ 5V
|VOUT| ≤ 5V
|VOUT| ≥ 5V
Adjust Pin Current Change
10mA ≤ IOUT ≤ IMAX
3V ≤ |VIN – VOUT| ≤ 35V
Minimum Load Current
|VIN – VOUT| ≤ 35V
|VIN – VOUT| ≤ 10V
ISC
Current Limit
|VIN – VOUT| ≤ 10V, (Note 3)
|VIN – VOUT| = 35V, TJ = 25°C
∆VOUT
∆Temp
Temperature Stability of
Output Voltage
TMIN ≤ T ≤ TMAX
∆VOUT
∆Time
Long Term Stability
TA = 125°C, 1000 Hours
en
RMS Output Noise
(% of VOUT)
TA = 25°C, 10Hz ≤ f ≤ 10kHz
θJC
Thermal Resistance
Junction to Case
T Package
K Package
P Package
MAX
UNITS
V
l
l
10
0.2
20
0.4
50
1.0
75
1.5
10
0.2
20
0.4
50
1.0
75
1.5
mV
%
mV
%
l
0.005
0.01
0.015
0.04
0.01
0.02
0.02
0.05
%/V
%/V
56
70
66
80
66
60
77
dB
dB
0.002
0.02
0.002
0.02
%/W
l
65
100
65
100
µA
l
l
0.2
1.0
2
5
0.5
2
2
5
µA
µA
2.5
1.2
5.0
3.0
2.5
1.2
5.0
3.0
mA
mA
4.3
1.3
6
2.5
4.3
1.3
6
2.5
A
A
0.6
1.5
0.6
1.5
%
0.3
1.0
0.3
1.0
%
3
0.5
l
0.003
1.2
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Unless otherwise indicated, these specifications apply:
|VIN – VOUT| = 5V; and IOUT = 5mA. Power dissipation is internally limited.
TYP
l –1.215 –1.250 –1.285 –1.200 –1.250 –1.300
TJ = 25°C, 10ms Pulse
∆IADJ
MIN
V
VOUT = –10V, f = 120Hz
CADJ = 0
CADJ = 10µF
Adjust Pin Current
LT1033C
MAX
–1.238 –1.250 –1.262 –1.238 –1.250 –1.262
3V ≤ |VIN – VOUT| ≤ 35V, (Note 2)
TJ = 25°C
IADJ
TYP
3
0.5
0.003
2.0
2.5
1.2
1.8
%
4.0
2.0
2.7
°C/W
°C/W
°C/W
However, these specifications apply for power dissipation up to 30W.
See guaranteed minimum output current curve. IMAX = 3A.
Note 3: Testing is done using a pulsed low duty cycle technique. See
thermal regulation specifications for output changes due to heating effects.
Load regulation is measured on the output pin at a point 1/8" below the
base of the package.
1033fd
For more information www.linear.com/LT1033
3
LT1033
Typical Performance Characteristics
Dropout Voltage
Temperature Stability
1.8
1.27
1.6
2.6
2.4
2.2
TJ = 25°C
2.0
TJ = 150°C
1.8
1.6
1.25
1.24
1.0
2.0
1.5
OUTPUT CURRENT (A)
2.5
3.0
1.23
–75 –50 –25
TJ = 25°C
0.8
0.6
TJ = 150°C
Ripple Rejection
40
VIN – VOUT = 5V
20 IL = 500mA
f = 120Hz
TJ = 25°C
0
0
–10
–20
–30
OUTPUT VOLTAGE (V)
100
80
80
60
40
20
0
–40
CADJ = 10µF
CADJ = 0
VIN = –15V
VOUT = –10V
IL = 500mA
TJ = 25°C
10
100
1k
10k
FREQUENCY (Hz)
100k
CADJ = 0
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
1033 G07
INPUT VOLTAGE
CHANGE (V)
CADJ = 10µF
0.1
1
OUTPUT CURRENT (A)
10
1033 G06
Load Transient Response
0.8
0.6
0.6
0.4
0.4
CADJ = 0
0.2
0
CADJ = 10µF
–0.2
VOUT = –10V
IL = 50mA
TJ = 25°C
CL = 1µF
0
–0.5
–1.0
CADJ = 0
0.2
0
CADJ = 10µF
–0.2
–0.4
–0.6
–0.4
10–2
VIN = –15V
VOUT = –10V
f = 120Hz
TJ = 25°C
0
0.01
1M
OUTPUT VOLTAGE
DEVIATION (V)
OUTPUT VOLTAGE
DEVIATION (V)
10–1
40
Line Transient Response
VIN = –15V
VOUT = –10V
IL = 500mA
CL = 1µF
TJ = 25°C
CADJ = 0
1033 G06
Output Impedance
100
CADJ = 10µF
60
20
1033 G04
101
40
Ripple Rejection
100
RIPPLE REJECTION (dB)
RIPPLE REJECTION (dB)
CADJ = 0
10
30
20
INPUT-OUTPUT DIFFERENTIAL (V)
1033 G03
Ripple Rejection
CADJ = 10µF
60
0
1033 G02
100
80
0
0 25 50 75 100 125 150
TEMPERATURE (°C)
0
10
20
TIME (µs)
30
40
1033 G08
LOAD CURRENT (A)
0.5
1033 G01
RIPPLE REJECTION (dB)
1.0
0.2
1.2
OUTPUT IMPEDANCE (Ω)
1.2
0.4
1.4
10–3
TJ = –55°C
1.4
1.26
CURRENT (mA)
TJ = –55°C
REFERENCE VOLTAGE (V)
INPUT-OUTPUT DIFFERENTIAL (V)
2.8
Minimum Load Current
0
VIN = –15V
VOUT = –10V
INL = 50mA
TJ = 25°C
CL = 1µF
–0.5
–1.0
–1.5
0
10
20
TIME (µs)
30
40
1033 G09
1033fd
4
For more information www.linear.com/LT1033
LT1033
Typical Performance Characteristics
Guaranteed Minimum
Output Current
Load Regulation*
Adjustment Current
80
0.4
0
–0.4
ADJUSTMENT CURRENT (µA)
4
OUTPUT CURRENT (A)
OUTPUT VOLTAGE DEVIATION (%)
5
0.8
3
2
1
75
70
65
60
55
–0.8
0
0.8
1.6
2.4
3.2
OUTPUT CURRENT (A)
4.0
*THE LT1033 HAS LOAD REGULATION COMPENSATION
WHICH MAKES THE TYPICAL UNIT READ CLOSE TO ZERO.
THIS BAND REPRESENTS THE TYPICAL PRODUCTION SPREAD
0
0
5
10
15
20
25
30
INPUT-OUTPUT DIFFERENTIAL (V)
35
1033 G11
50
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
1033 G12
1033 G10
1033fd
For more information www.linear.com/LT1033
5
LT1033
Schematic Diagram
ADJ
2k
2k
Q1
Q2
D4
20k
Q4
Q3
15pF
D1
750Ω
Q6
D2
60k
Q7
VOUT
800Ω
D3
Q32
100k
Q34
5k
15pF
2k
25pF
600Ω
Q33
18k
Q8
D5
100k
220Ω
Q11
Q10
Q9
Q12
20Ω
20Ω
Q25
6.8k
Q23
Q13
4k
Q22
1k
600Ω
Q20
Q18
Q14
Q15
Q17
4.2k
8k
Q27
4k
20k
Q26
250Ω
2pF
460Ω
12k
Q24
Q28
150Ω
Q31
Q30
Q19
Q16
5pF
15k
Q21
12k
270Ω
12k
10Ω
100Ω
2k
6k
1k
0.02Ω
Q29
1k
2.4k
500Ω
100Ω
VIN
1033 SC01
1033fd
6
For more information www.linear.com/LT1033
LT1033
Applications Information
Output Voltage
The output voltage is determined by two external resistors, R1 and R2 (see Figure 1). The exact formula for the
output voltage is:
Capacitors and Protection Diodes
R2
VOUT = VREF 1+ +IADJ (R2)
R1
Where: VREF = Reference Voltage, IADJ = Adjustment Pin
Current. In most applications, the second term is small
enough to be ignored, typically about 0.5% of VOUT. In
more critical applications, the exact formula should be
used, with IADJ equal to 65µA. Solving for R2 yields:
R2 =
VOUT – VREF
VREF
–I
R1 ADJ
Smaller values of R1 and R2 will reduce the influence of
IADJ on the output voltage, but the no-load current drain
on the regulator will be increased. Typical values for R1
are between 100Ω and 300Ω, giving 12.5mA and 4.2mA
no-load current respectively. There is an additional consideration in selecting R1, the minimum load current
specification of the regulator. The operating current of
the LT1033 flows from input to output. If this current is
not absorbed by the load, the output of the regulator will
rise above the regulated value. The current drawn by R1
and R2 is normally high enough to absorb the current, but
care must be taken in no-load situations where R1 and R2
+
+
C1
10µF
C2
5µF
–VIN
VIN
LT1033
R2
+
IADJ
VREF
ADJ
C3
2µF
R1
–VOUT
VOUT
1033 F01
EXAMPLE:
1. A PRECISION 10V REGULATOR TO SUPPLY UP TO 3A LOAD CURRENT.
A. SELECT R1 = 100Ω TO MINIMIZE EFFECT OF IADJ
B. CALCULATE R2 =
VOUT – VREF 10V – 1.25V
=
= 704Ω
VREF
1.25V
– 65µA
– IADJ
100Ω
R1
Figure 1.
have high values. The maximum value for the operating
current, which must be absorbed, is 5mA for the LT1033.
If input-output voltage differential is less than 10V, the
operating current that must be absorbed drops to 3mA.
An output capacitor, C3, is required to provide proper
frequency compensation of the regulator feedback loop.
A 2µF or larger solid tantalum capacitor is generally
sufficient for this purpose if the 1MHz impedance of the
capacitor is 1Ω or less. High Q capacitors, such as Mylar,
are not recommended because their extremely low ESR
(effective series resistance) can drastically reduce phase
margin. When these types of capacitors must be used
because of other considerations, add a 0.5Ω carbon resistor in series with 1µF. Aluminum electrolytic capacitors
may be used, but the minimum value should be 25µF to
ensure a low impedance at 1MHz. The output capacitor
should be located within a few inches of the regulator to
keep lead impedance to a minimum. The following caution
should be noted: if the output voltage is greater than 6V
and an output capacitor greater than 20µF has been used,
it is possible to damage the regulator if the input voltage
becomes shorted, due to the output capacitor discharging
into the regulator. This can be prevented by using diode
D1 (see Figure 2) between the input and the output.
The input capacitor, C2, is only required if the regulator is
more than 4 inches from the raw supply filter capacitor.
Bypassing the Adjustment Pin
The adjustment pin of the LT1033 may be bypassed with a
capacitor to ground, C1, to reduce output ripple, noise, and
impedance. These parameters scale directly with output
voltage if the adjustment pin is not bypassed. A bypass
capacitor reduces ripple, noise and impedance to that of
a 1.25V regulator. In a 15V regulator for example, these
parameters are improved by 15V/1.25V = 12 to 1. This
improvement holds only for those frequencies where the
impedance of the bypass capacitor is less than R1. Ten
microfarads is generally sufficient for 60Hz power line
applications where the ripple frequency is 120Hz, since
XC = 130Ω. The capacitor should have a voltage rating at
least as high as the output voltage of the regulator. Values
1033fd
For more information www.linear.com/LT1033
7
LT1033
Applications Information
larger than 10µF may be used, but if the output is larger
than 25V, a diode, D2, should be added between the output
and adjustment pins (see Figure 2).
+
C1
R2
+
Proper Connection of Divider Resistors
R1
The LT1033 has a load regulation specification of 0.8%
and is measured at a point 1/8" from the bottom of the
package. To prevent degradation of load regulation, the
resistors which set output voltage, R1 and R2, must be
connected as shown in Figure 3. Note that the positive side
of the load has a true force and sense (Kelvin) connection,
but the negative side of the load does not.
ADJ
VIN
–VIN
LT1033
C3
D2**
1N4002
–VOUT
VOUT
D1* 1N4002
1033 F02
*D1 PROTECTS THE REGULATOR FROM INPUT SHORTS TO GROUND. IT IS
REQUIRED ONLY WHEN C3 IS LARGER THAN 20µF AND VOUT IS LARGER
THAN 6V
** D2 PROTECTS THE ADJUST PIN OF THE REGULATOR FROM OUTPUT
SHORTS IF C2 IS LARGER THAN 10µF AND VOUT IS LARGER THAN –25V
R1 should be connected directly to the output lead of the
regulator, as close as possible to the specified point 1/8"
from the case. R2 should be connected to the positive
side of the load separately from the positive (ground)
connection to the raw supply. With this arrangement, load
regulation is degraded only by the resistance between the
regulator output pin and the load. If R1 is connected to
the load, regulation will be degraded.
Figure 2.
LEAD RESISTANCE HERE DOES
NOT AFFECT LOAD REGULATION
R2
LOAD
R1
ADJ
–VIN
VIN
VOUT
1033 F03
LT1033
CONNECT R1
DIRECTLY TO
REGULATOR PIN
LEAD RESISTANCE HERE
DEGRADES LOAD
REGULATION. MINIMIZE
THE LENGTH OF THIS LEAD
Figure 3.
1033fd
8
For more information www.linear.com/LT1033
LT1033
Typical applications
The output stability, load regulation, line regulation,
thermal regulation, temperature drift, long term drift, and
noise can be improved by a factor of 6.6 over the standard
regulator configuration. This assumes a zener whose drift
and noise is considerably better than the regulator itself.
The LM329B has 20ppm/°C maximum drift and about 10
times lower noise than the regulator.
In the application shown below, regulators #2 to “N”
will track regulator #1 to within ±24mV initially, and to
±60mV over all load, line, and temperature conditions.
If any regulator output is shorted to ground, all other
outputs will drop to ≈ –2V. Load regulation of regulators
#2 to “N” will be improved by VOUT/1.25V compared to
a standard regulator, so regulator #1 should be the one
which has the lowest load current.
High Stability Regulator
7V
LM329B
R2*
R3
1.5k
1%
+ 1µF
R1
1k
1%
SOLID
TANTALUM
ADJ
VIN
–VIN
LT1033
VOUT
*R2 =
|VOUT|
9.08 • 10–3
–VOUT
– 908Ω
1033 TA03
Dual Tracking 3A Supply ±1.25V to ±20V
LT150A
VIN
+VIN
VOUT
+VOUT
ADJ
Multiple Tracking Regulators
+
C3
10µF
+
R1**
100Ω
1%
R2
2µF
ADJ
–VIN
1N4002
10µF
+
R1
120Ω
C1
2µF
SOLID
TANTALUM
10µF
+
R2
5k
1%
+
2.2µF*
D1
1N4002
+
2.2µF*
D2
1N4002
R3
5k
R4
5k
1%
–VOUT1
VIN REG #1 VOUT
+
R5**
100Ω
1%
LT1033
ADJ
+
+
2µF
ADJ
1N4002
VIN REG #2 VOUT
VIN
–VIN
2µF
SOLID
TANTALUM
–VOUT2
LT1033
VOUT
–VOUT
1033 TA04
*SOLID TANTALUM
**R1 OR R5 MAY BE TRIMMED SLIGHTLY TO IMPROVE TRACKING
LT1033
+
+
2µF
ADJ
VIN REG #N VOUT
LT1033
Current Regulator
2µF
SOLID
TANTALUM
–VOUT3
1033 TA02
+
ADJ
(–)
VIN
LT1033
VOUT
C1
2µF
SOLID TANTALUM
RS
(O.5Ω ≤ RS ≤ 250Ω)
(+)
I
I = 65µA +
1.25V
RS
1033 TA05
1033fd
For more information www.linear.com/LT1033
9
LT1033
Program Resistor Selection
The following table allows convenient selection of
program resistors from standard 1% values.
VOUT
R1
R2
OUTPUT ERROR
(%)
5
100
301
0.6
6
121
453
–0.7
8
115
619
0.6
10
115
806
0.6
12
118
1020
1.0
15
100
1100
0.5
18
150
2000
0.2
20
121
1820
0.8
22
130
2150
0.2
24
121
2210
0.9
28
115
2430
–0.7
30
121
2740
–0.9
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
K Package
2-Lead TO-3 Metal Can
(Reference LTC DWG # 05-08-1310)
0.760 – 0.775
(19.30 – 19.69)
0.320 – 0.350
(8.13 – 8.89)
0.060 – 0.135
(1.524 – 3.429)
0.420 – 0.480
(10.67 – 12.19)
0.038 – 0.043
(0.965 – 1.09)
1.177 – 1.197
(29.90 – 30.40)
0.655 – 0.675
(16.64 – 17.15)
0.210 – 0.220
(5.33 – 5.59)
0.425 – 0.435
(10.80 – 11.05)
0.151 – 0.161
(3.86 – 4.09)
DIA, 2PLCS
0.167 – 0.177
(4.24 – 4.49)
R
0.067 – 0.077
(1.70 – 1.96)
0.490 – 0.510
(12.45 – 12.95)
R
K2 (TO-3) 1098
OBSOLETE PACKAGE
1033fd
10
For more information www.linear.com/LT1033
LT1033
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
T Package
3-Lead Plastic TO-220
(Reference LTC DWG # 05-08-1420)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.165 – 0.180
(4.191 – 4.572)
0.045 – 0.055
(1.143 – 1.397)
0.230 – 0.270
(5.842 – 6.858)
0.570 – 0.620
(14.478 – 15.748)
0.460 – 0.500
(11.684 – 12.700)
0.330 – 0.370
(8.382 – 9.398)
0.980 – 1.070
(24.892 – 27.178)
0.520 – 0.570
(13.208 – 14.478)
0.100
(2.540)
BSC
0.218 – 0.252
(5.537 – 6.401)
0.028 – 0.038
(0.711 – 0.965)
0.050
(1.270)
TYP
0.013 – 0.023
(0.330 – 0.584)
0.095 – 0.115
(2.413 – 2.921)
T3 (TO-220) 1098
1033fd
For more information www.linear.com/LT1033
11
LT1033
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
P Package
3-Lead Plastic TO-3P (Similar to TO-247))
(Reference LTC DWG # 05-08-1450 Rev A)
.515 – .580
(13.08 – 14.73)
.305 – .370
(7.75 – 9.40)
.560 – .620
(14.22 – 15.75)
.187 – .207
(4.75 – 5.26)
.620 – .640
(15.75 – 16.26)
.265 – .293
(6.73 – 7.44)
MOUNTING HOLE
18° – 22°
.115 – .145
(2.92 – 3.68)
DIA
.819 – .870
(20.80 – 22.10)
.635 – .720
(16.13 – 18.29)
.060 – .081
(1.52 – 2.06)
.170 – .215
(4.32 – 5.46)
EJECTOR PIN MARKS
.105 – .125
(2.67 – 3.18)
DIA
.580 – .600
(14.73 – 15.24)
3° – 7°
.104 – .145
(2.64 – 3.68)
.170
(4.32)
MAX
.780 – .800
(19.81 – 20.32)
.042 – .052
(1.07 – 1.32)
BOTTOM VIEW OF TO-3P
HATCHED AREA IS SOLDER PLATED
COPPER HEAT SINK
NOTE:
1. DIMENSIONS IN INCH/(MILLIMETER)
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED .030" (.762mm)
.074 – .084
(1.88 – 2.13)
.215
(5.46)
BSC
.113 – .123
(2.87 – 3.12)
.087 – .102
(2.21 – 2.59)
.020 – .040
(0.51 – 1.02)
P3 0512 REV A
OBSOLETE PACKAGE
1033fd
12
For more information www.linear.com/LT1033
LT1033
Revision History
(Revision history begins at Rev D)
REV
DATE
DESCRIPTION
PAGE NUMBER
D
6/15
Obsoleted TO-3P package
2, 12
1033fd
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LT1033
13
LT1033
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LT1120
125mA Low Dropout Regulator with 20µA IQ
Includes 2.5V Reference and Comparator
LT1121
150mA Micropower Low Dropout Regulator
30µA IQ, SOT-223 Package
LT1129
700mA Micropower Low Dropout Regulator
50µA Quiescent Current
LT1175
500mA Negative Low Dropout Micropower Regulator
45µA IQ, 0.26V Dropout Voltage, SOT-223 Package
LT1521
300mA Low Dropout Micropower Regulator with
Shutdown
15µA IQ, Reverse Battery Protection
LT1529
3A Low Dropout Regulator with 50µA IQ
500mV Dropout Voltage
LT1573
UltraFast™ Transient Response Low Dropout Regulator
Drives External PNP
LT1575
UltraFast Transient Response Low Dropout Regulator
Drives External N-Channel MOSFET
LT1761 Series
100mA, Low Noise, Low Dropout Micropower
Regulators in SOT-23
20µA Quiescent Current, 20µVRMS Noise, SOT-23 Package
LT1762 Series
150mA, Low Noise, LDO Micropower Regulators
25µA Quiescent Current, 20µVRMS Noise, MSOP Package
LT1763 Series
500mA, Low Noise, LDO Micropower Regulators
30µA Quiescent Current, 20µVRMS Noise, SO-8 Package
LT1764
3A, Low Noise, Fast Transient Response LDO
40µVRMS Noise
LT1962
300mA, Low Noise, LDO Micropower Regulator
20µVRMS Noise, MSOP Package
LT1963
1.5A, Low Noise, Fast Transient Response LDO
40µVRMS Noise, SOT-223 Package
LT1185
3A Negative Low Dropout Regulator
VIN: –4.5V to –35V, 0.8V Dropout Voltage, DD-Pak and TO-220 Packages
LT1964
200mA, Low Noise, Negative LDO
340mV Dropout Voltage, Low Noise 30µVRMS, VIN = –1.8V to –20V,
ThinSOT™ and 3mm × 3mm DFN-8 Packages
LT3015
1.5A, Low Noise, Negative Linear Regulator with
Precision Current Limit
VIN: –1.8V to –30V, VOUT: –1.22V to –29.5V, Dropout Voltage: 310mV,
Precision Current Limit with Foldback, Low Output Noise: 60μVRMS (10Hz to
100kHz), TO-220, DD-Pak, DFN and MSOP Packages
LT3080/LT3080-1 1.1A, Parallelable, Low Noise, Low Dropout Linear
Regulator
300mV Dropout Voltage (2-Supply Operation), Low Noise: 40µVRMS,
VIN: 1.2V to 36V, VOUT: 0V to 35.7V, Stable with Ceramic Caps, TO-220,
DD-Pak, SOT-223, MS8E and 3mm × 3mm DFN-8 Packages; –1 Version Has
Integrated Internal Ballast Resistor
LT3090
300mV Dropout Voltage, 18µVRMS Output Voltage Noise, Parallelable 50μA
SET Pin Current: ±1% Initial Accuracy, Positive/Negative Current Monitors
Wide Input Voltage Range: –1.5V to –36V, Rail-to-Rail Output Voltage
Range: 0V to –32V
600mA Low Noise Negative LDO with Programmable
ILimit
1033fd
14 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LT1033
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LT1033
LT 0615 REV D • PRINTED IN USA
LINEAR TECHNOLOGY CORPORATION 1991
工商网监
湘ICP备2023018690号
