LT1109CZ-12#PBF

LT1109 Micropower Low Cost DC/DC Converter Adjustable and Fixed 5V, 12V U DESCRIPTIO FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Uses Off-the-Shelf Inductors Only 33µH Inductor Required Low Cost 3-Lead TO-92, SO8, or 8-Pin DIP Adjustable or Fixed 5V or 12V Output 120kHz Oscillator Only Three External Components Required 320µA IQ 1.6V Minimum Start-Up Voltage Logic Controlled Shutdown The LT1109 is a simple step-up DC/DC converter. Available in 8-pin SO, 3-lead TO-92 (fixed output only) or miniDIP packages, the devices require only three external components to construct a complete DC/DC converter. Current drain is just 320µA at no load, making the device ideal for cost-sensitive applications where standby current must be kept to a minimum. The LT1109-5 can deliver 5V at 100mA from a 3V input and the LT1109-12 can deliver 12V at 60mA from a 5V input. The 8-pin versions also feature a logic controlled SHUTDOWN pin that turns off the oscillator when taken low. The gated-oscillator design requires no frequency compensation components. The high frequency 120kHz oscillator permits the use of small surface mount inductors and capacitors. For a 5V to 12V at 120mA converter, see the LT1109A. Foa a 5V to 12V at 200mA converter with 20µA shutdown current, see the LT1301. UO APPLICATI ■ ■ ■ ■ ■ ■ ■ S Flash Memory VPP Generators 3V to 5V Converters 5V to 12V Converters Disk Drives PC Plug-In Cards Peripherals Battery-Powered Equipment UO TYPICAL APPLICATI All Surface Mount Flash Memory VPP Generator Output Voltage Flash Memory Program Output 15 L1✝ 33µH MBRS120T3 VIN = 5V VOUT 5V/DIV VIN 5V 1 SW VIN SENSE VOUT 12V 80mA 8 LT1109CS8-12 7 SHUTDOWN* GND + C1** 22µF 16V OV 9 SHUTDOWN 5V/DIV 6 1ms/DIV LT1109 • TA02 3 4 SHUTDOWN OUTPUT VOLTAGE (V) 12 3 PROGRAM * 8-PIN PACKAGE ONLY ✝ L1 = SUMIDA CD54-330LC (I OUT = 80mA) COILTRONICS CTX33-1 (80mA) MURATA-ERIE LQH4N330K (I OUT = 50mA) ISI LCS2414-330K (IOUT = 50mA) **C1 = MATSUO 267M1602226 OR EQUIVALENT LT1109 • TA01 0 0 10 20 30 40 50 60 70 80 90 100 OUTPUT CURRENT (mA) LT1109 • TPC01 1 LT1109 W W W AXI U U ABSOLUTE RATI GS (Voltages Referred to GND Pin) Supply Voltage (VOUT) .............................. – 0.4V to 20V SW Pin Voltage .......................................... – 0.4V to 50V SHUTDOWN Pin Voltage......................................... 6.0V Maximum Power Dissipation ............................. 300mW Operating Temperature Range ..................... 0°C to 70°C Storage Temperature Range ................. – 65°C to 150°C Lead Temperature (Soldering, 10 sec.)................. 300°C Switch Current ........................................................ 1.2A W U U PACKAGE/ORDER I FOR ATIO VIN 1 BOTTOM VIEW TOP VIEW TOP VIEW 8 VIN 1 SENSE 8 NC 2 7 SHUTDOWN NC 2 7 SHUTDOWN SW 3 6 NC SW 3 6 NC GND 4 5 NC GND 4 5 NC N8 PACKAGE 8-LEAD PLASTIC DIP S8 PACKAGE 8-LEAD PLASTIC SOIC LT1109 • PO102 ORDER PART NUMBER LT1109CN8 LT1109CN8-5 LT1109CN8-12 2 1 SW GND Z PACKAGE 3-LEAD TO-92 PLASTIC LT1109 • PO103 TJMAX = 100°C, θJA = 150°C/W TJMAX = 100°C, θJA = 130°C/W 3 VOUT SENSE LT1109 • POI01 TJMAX = 100°C, θJA = 160°C/W ORDER PART NUMBER S8 PART MARKING ORDER PART NUMBER LT1109CS8 LT1109CS8-5 LT1109CS8-12 1109 10905 10912 LT1109CZ-5 LT1109CZ-12 ELECTRICAL CHARACTERISTICS TA = 25°C, VIN = 3V (LT1109CN8, LT1109CS8), unless otherwise specified. SYMBOL PARAMETER CONDITIONS IQ Quiescent Current Switch Off MIN ● Minimum Start-Up Voltage at VOUT Pin (Z Package) VIN VOUT fOSC tON Input Voltage (N8, S8 Package) MAX UNITS 320 550 µA 1.6 V ● 3 V Comparative Trip Point Voltage LT1109 ● 1.20 1.25 1.30 V Output Voltage LT1109-5; 3V ≤ VIN ≤ 5V LT1109-12; 3V ≤ VIN ≤ 12V ● ● 4.75 11.52 5.00 12.00 5.25 12.55 V V Comparator Hysteresis LT1109 ● 8 12.5 mV Output Voltage Ripple LT1109-5 LT1109-12 ● ● 25 60 50 120 mV mV Oscillator Frequency 100 90 120 ● 140 150 kHz kHz 3.3 3.0 4.2 ● 5.3 5.5 µs µs 45 50 60 % 0.4 0.5 0.7 0.8 V V Switch ON Time DC Duty Cycle Full Load ● VCESAT Switch Saturation Voltage ISW = 500mA LT1109-5: VIN = 3V; LT1109-12: VIN = 5V ● 2 TYP LT1109 ELECTRICAL CHARACTERISTICS TA = 25°C, VIN = 3V (LT1109CN8, LT1109CS8), unless otherwise specified. SYMBOL PARAMETER CONDITIONS Switch Leakage Current VSW = 12V MIN TYP MAX 1 10 UNITS VIH SHUTDOWN Pin High N8, S8 Package ● VIL SHUTDOWN Pin Low N8, S8 Package ● 0.8 V IIH SHUTDOWN Pin Input Current N8, S8 Package, VSHUTDOWN = 4V ● 10 µA IIL SHUTDOWN Pin Input Current N8, S8 Package, VSHUTDOWN = 0V ● 20 µA µA 2.0 V The ● denotes the specifications which apply over the full operating temperature range. U W TYPICAL PERFOR A CE CHARACTERISTICS Oscillator Frequency Oscillator Frequency 160 Switch ON Time 130 7 FREQUENCY (kHz) 120 100 80 126 SWITCH ON TIME (µs) OSCILLATOR FREQUENCY (kHz) 128 140 124 122 120 118 116 114 6 5 4 112 60 –50 0 –25 25 50 75 110 100 0 2 4 TEMPERATURE (°C) 6 8 700 65 600 60 1.0 100 VIN = 5V TA = 25°C 0.8 VCESAT (V) VCESAT (mV) 75 Switch Saturation Voltage 500 45 50 1.2 ISW = 500mA 50 25 LT1109 • TPC04 Switch Saturation Voltage 70 55 0 TEMPERATURE (°C) LT1109 • TPC03 Duty Cycle DUTY CYCLE (%) –25 INPUT VOLTAGE (V) LT1109 • TPC02 400 300 0.6 0.4 200 40 0.2 100 35 30 –50 3 –50 10 12 14 16 18 20 –25 0 25 50 75 100 0 –50 0 –25 0 25 50 75 100 TEMPERATURE (°C) TEMPERATURE (°C) LT1109 • TPC05 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 SWITCH CURRENT (A) LT1109 • TPC06 LT1109 • TPC07 3 LT1109 U W TYPICAL PERFOR A CE CHARACTERISTICS Minimum/Maximum Oscillator Frequency vs tON Quiescent Current 400 0°C ≤ TA ≤ 70°C TA = 25°C 140 130 TA = 25°C 120 110 100 380 400 QUIESCENT CURRENT (µA) QUIESCENT CURRENT (µA) 150 OSCILLATOR FREQUENCY (kHz) Quiescent Current 450 160 350 300 250 90 360 340 320 300 280 260 240 220 200 80 2.0 2.5 3.0 4.0 3.5 4.5 5.0 6.0 5.5 0 2 4 6 8 200 –50 10 12 14 16 18 20 –25 INPUT VOLTAGE (V) TON (µs) 0 25 50 100 TEMPERATURE (°C) LT1109 • TPC09 LT1109 • TPC08 75 LT1109 • TPC10 W BLOCK DIAGRA S LT1109-5, -12 N8, S8 Package LT1109-5, -12 Z Package VOUT VIN FB SENSE R2 250k SW R2 250k 1.25V REFERENCE SW COMPARATOR 1.25V REFERENCE + A1 + 120kHz OSCILLATOR A1 – 120kHz OSCILLATOR – Q1 Q1 DRIVER DRIVER COMPARATOR R1 R1 GND GND LT1109-5: R1 = 83k LT1109-12: R1 = 29k LT1109 • TA03 SHUTDOWN LT1109 • TA04 ON FIXED VERSION PIN 8 IS SENSE ON ADJUSTABLE VERSION PIN 8 IS FB AND R1 AND R2 ARE DISCONNECTED U LT1109Z OPERATIO The LT1109Z-5 and LT1109Z-12 are fixed output voltage step-up DC/DC converters in a 3-pin TO-92 package. Power for internal regulator circuitry is taken from the VOUT pin, a technique known as “bootstrapping.” Circuit operation can be best understood by referring to the block diagram. VOUT, attenuated by R1 and R2, is applied to the negative input of comparator A1. When this voltage falls below the 1.25V reference voltage, the oscillator is turned on and the power switch Q1 cycles at the oscillator 4 frequency of 120kHz. Switch cycling alternately builds current in the inductor, then dumps it into the output capacitor, increasing the output voltage. When A1’s negative input rises above 1.25V, it turns off the oscillator. A small amount of hysteresis in A1 obviates the need for frequency compensation circuitry. When Q1 is off, current into the VOUT pin drops to just 320µA. Quiescent current from the battery will be higher because the device operates off the stepped-up voltage. LT1109 U U U LT1109 S8 A D 8 OPERATIO The 8-pin versions of the LT1109 have separate pins for VIN and SENSE or FB and also have a SHUTDOWN pin. Separating the device VIN pin from the SENSE pin allows the device to be powered from the (lower) input voltage rather than the (higher) output voltage. Although quiescent current remains constant, quiescent power will be U W U UO APPLICATI reduced by using the 8-pin version since the quiescent current flows from a lower voltage source. The SHUTDOWN pin disables the oscillator when taken to a logic “0.” If left floating or tied high, the converter operates normally. With SHUTDOWN low, quiescent current remains at 320µA. S I FOR ATIO Inductor Selection A DC/DC converter operates by storing energy as magnetic flux in an inductor core, and then switching this energy into the load. To operate as an efficient energy transfer element, the inductor must fulfill three requirements. First, the inductance must be low enough for the inductor to store adequate energy under the worst case condition of minimum input voltage and switch-ON time. The inductance must also be high enough so that maximum current ratings of the LT1109 and inductor are not exceeded at the other worst case condition of maximum input voltage and ON time. Additionally, the inductor core must be able to store the required flux; i.e., it must not saturate. At power levels generally encountered with LT1109 designs, small ferrite surface-mount inductors will function well. Lastly, the inductor must have sufficiently low DC resistance so that excessive power is not lost as heat in the windings. Look for DCR values in the inductors’ specification tables; values under 0.5Ω will give best efficiency. An additional consideration is ElectroMagnetic Interference (EMI). Toroid and pot core type inductors are recommended in applications where EMI must be kept to a minimum; for example, where there are sensitive analog circuitry or transducers nearby. Rod core types are a less expensive choice where EMI is not a problem. Specifying a proper inductor for an application requires first establishing minimum and maximum input voltage, output voltage, and output current. In a step-up converter, the inductive events add to the input voltage to produce the output voltage. Power required from the inductor is determined by PL = (VOUT + VD – VIN) (IOUT) (01) where VD is the diode drop (0.5V for a 1N5818 Schottky). Energy required by the inductor per cycle must be equal or greater than (02) PL FOSC in order for the converter to regulate the output. When the switch is closed, current in the inductor builds according to –R't  V  IL t = IN  1 – e L  R'   () (03) where R' is the sum of the switch equivalent resistance (0.8 typical at 25°C) and the inductor DC resistance. When the drop across the switch is small compared to VIN, the simple lossless equation () V IL t = IN t L (04) can be used. These equations assume that at t = 0, inductor current is zero. This situation is called “discontinuous mode operation” in switching regulator parlance. Setting “t” to the switch-ON time from the LT1109 specification table (typically 4.2µs) will yield IPEAK for a specific “L” and VIN. Once IPEAK is known, energy in the inductor at the end of the switch-ON time can be calculated as EL = 1 2 LI 2 PEAK (05) EL must be greater than PL/FOSC for the converter to deliver the required power. For best efficiency IPEAK should be 5 LT1109 U W U UO APPLICATI S I FOR ATIO kept to 600mA or less. Higher switch currents will cause excessive drop across the switch resulting in reduced efficiency. In general, switch current should be held to as low a value as possible in order to keep switch, diode and inductor losses at a minimum. As an example, suppose 12V at 60mA is to be generated from a 4.5V input. Recalling Equation 01, PL = (12V + 0.5V – 4.5V) (60mA) = 480mW. (06) Energy required from the inductor is PL FOSC = 480mW = 4.0µJ. 120kHz (07) Picking an inductor value of 33µH with 0.2Ω DCR results in a peak switch current of I PEAK = –1.0 • 4.2µ s  4.5 V  e 1 – 33µ H  = 538m A. 1.0Ω   (08) Substituting IPEAK into Equation 03 results in EL = ( )( ) 2 1 33µH 0.538 A = 4.77µJ. 2 (09) Since 4.77µJ > 4µJ the 33µH inductor will work. This trialand-error approach can be used to select the optimum inductor. Keep in mind the switch current maximum rating of 1.2A. If the calculated peak current exceeds this, the input voltage must be increased or the load decreased. Capacitor Selection The output capacitor should be chosen on the basis of its equivalent series resistance (ESR). Surface-mount tantalum electrolytics can be used provided the ESR value is sufficiently low. An ESR of 0.1Ω will result in a 50mV step at the output of the converter when the peak inductor current is 500mA. Physically larger capacitors have lower ESR. Diode Selection Speed, forward drop, and leakage current are the three main considerations in selecting a catch diode for LT1109 converters. General purpose rectifiers such as the 1N4001 6 are unsuitable for use in any switching regulator application. Although they are rated at 1A, the switching time of a 1N4001 is in the 10µs-50µs range. At best, efficiency will be severely compromised when these diodes are used; at worst, the circuit may not work at all. Most LT1109 circuits will be well served by a 1N5818 Schottky diode. The combination of 500mV forward drop at 1A current, fast turn-ON and turn-OFF time, and 4µA to 10µA leakage current fit nicely with LT1109 requirements. At peak switch currents of 100mA or less, a 1N4148 signal diode may be used. This diode has leakage current in the 1nA to 5nA range at 25°C and lower cost than a 1N5818. Table 1. Inductor Manufacturers MANUFACTURER PART NUMBERS Caddell-Burns 258 East Second Street Mineola, NY 11501 516-746-2310 7120 Series Coiltronics Incorporated 6000 Park of Commerce Blvd. Boca Raton, FL 33487 407-241-7876 Surface Mount CTX33-1 Coilcraft 1102 Silver Lake Road Cary, IL 60013 708-639-6400 DT3316 Series Sumida Electric Co., Ltd. 637 E. Golf Road, Suite 209 Arlington Heights, IL 60005 708-956-0666 CD54 CD105 Surface Mount Table 2. Capacitor Manufacturers MANUFACTURER PART NUMBERS Sanyo Video Components 2001 Sanyo Avenue San Diego, CA 92173 619-661-6835 OS-CON Series Matsuo Electronics 2134 Main Street, Suite 200 Huntington Beach, CA 92648 714-969-2491 267 Series Kemet Electronics Corporation Box 5928 Greenville, SC 29606 803-963-6621 T491 Series Philips Components 2001 W. Blue Heron Blvd. P.O. Box 10330 Riviera Beach, FL 33404 407-881-3200 49MC Series LT1109 UO TYPICAL APPLICATI S 3V to 5V Converter 3-Pin Package Flash Memory VPP Generator VIN 5V 33µH CADDELL-BURNS 7120-19 22µH CADDELL-BURNS 7120-17 1N4933 12V 30mA 1N5818 5V 100mA AT 3V INPUT 20mA AT 2V INPUT 10k SW 2N4403 VOUT SW VOUT 2 CELLS + LT1109CZ-12 LT1109CZ-5 + 10µF 20V GND 10k 22µF 16V GND LT1109 • TA06 SHUTDOWN VN2222 PROGRAM QUIESCENT CURRENT = 0 IN SHUTDOWN LT1109 • TA05 3V to 5V Converter with Shutdown 3V to 12V Converter 22µH CADDELL-BURNS 7120-17 L1* 22µH 1N5818 12V 40mA AT 3V INPUT 15mA AT 2V INPUT VIN SW SW VOUT 2 CELLS 2 CELLS LT1109CZ-12 + GND 10µF 20V LT1109 • TA07 MBRS120T3 LT1109CS8-5 SDN SHUTDOWN 5V OUTPUT SENSE GND + 22µF 16V *L1 = SUMIDA CD54-220LC LT1109 • TA08 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 7 LT1109 U PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted. N8 Package 8-Lead Plastic DIP 0.300 – 0.320 (7.620 – 8.128) 0.045 – 0.065 (1.143 – 1.651) ( 0.130 ± 0.005 (3.302 ± 0.127) 8 7 6 +0.025 0.325 –0.015 0.250 ± 0.010 (6.350 ± 0.254) 0.125 (3.175) MIN 0.045 ± 0.015 (1.143 ± 0.381) ) 0.100 ± 0.010 (2.540 ± 0.254) 0.020 (0.508) MIN 1 2 0.010 – 0.020 × 45° (0.254 – 0.508) 0.018 ± 0.003 (0.457 ± 0.076) N8 0392 0.189 – 0.197 (4.801 – 5.004) 8 0.053 – 0.069 (1.346 – 1.752) 7 6 5 0.004 – 0.010 (0.101 – 0.254) 0.008 – 0.010 (0.203 – 0.254) 0°– 8° TYP 4 3 S8 Package 8-Lead Plastic SOIC 0.016 – 0.050 0.406 – 1.270 5 0.065 (1.651) TYP 0.009 – 0.015 (0.229 – 0.381) +0.635 8.255 –0.381 0.400 (10.160) MAX 0.014 – 0.019 (0.355 – 0.483) 0.050 (1.270) BSC 0.228 – 0.244 (5.791 – 6.197) 0.150 – 0.157 (3.810 – 3.988) 1 3 2 4 SO8 0392 Z Package 3-Lead TO-92 Plastic 0.060 ± 0.005 (1.524± 0.127) DIA 0.180 ± 0.005 (4.572 ± 0.127) 0.060 ± 0.010 (1.524 ± 0.254) 0.90 (2.286) NOM 0.180 ± 0.005 (4.572 ± 0.127) 0.500 (12.79) MIN 0.050 (1.270) MAX 0.140 ± 0.010 (3.556 ± 0.127) 5° NOM 10° NOM UNCONTROLLED LEAD DIA 0.020 ± 0.003 (0.508 ± 0.076) 0.050 ± 0.005 (1.270 ± 0.127) 8 0.015 ± 0.02 (0.381 ± 0.051) Z3 1191 0.016 ± 0.03 (0.406 ± 0.076) Linear Technology Corporation LT/GP 1093 5K REV B • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7487 (408) 432-1900 ● FAX: (408) 434-0507 ● TELEX: 499-3977  LINEAR TECHNOLOGY CORPORATION 1993