LT3045-1
20V, 500mA, Ultralow Noise,
Ultrahigh PSRR Linear Regulator with VIOC Control
FEATURES
DESCRIPTION
Ultralow RMS Noise: 0.8µVRMS (10Hz to 100kHz)
nn Ultralow Spot Noise: 2nV/√Hz at 10kHz
nn Ultrahigh PSRR: 76dB at 1MHz
nn Output Current: 500mA
nn Wide Input Voltage Range: 1.8V to 20V
nn Single Capacitor Improves Noise and PSRR
nn 100µA SET Pin Current: ±1% Initial Accuracy
nn VIOC Pin Controls Upstream Regulator to Minimize
Power Dissipation
nn Single Resistor Programs Output Voltage
nn Programmable Current Limit
nn Low Dropout Voltage: 260mV
nn Output Voltage Range: 0V to 15V
nn Programmable Power Good
nn Fast Start-Up Capability
nn Precision Enable/UVLO
nn Parallelable for Lower Noise and Higher Current
nn Internal Current Limit with Foldback
nn Minimum Output Capacitor: 10µF Ceramic
nn Reverse-Battery and Reverse-Current Protection
nn 12-Lead MSOP and 3mm × 3mm DFN Packages
The LT®3045-1 is a high performance low dropout linear
regulator featuring LTC’s ultralow noise and ultrahigh PSRR
architecture for powering noise sensitive applications. Designed as a precision current reference followed by a high
performance voltage buffer, the LT3045-1 can be easily
paralleled to further reduce noise, increase output current
and spread heat on the PCB. In addition to the LT3045
feature set, the LT3045-1 incorporates a VIOC tracking
function to control an upstream switching converter to
maintain a constant voltage across the LT3045-1 and
hence minimize power dissipation.
APPLICATIONS
The LT3045-1 is stable with a minimum 10µF ceramic
output capacitor. Built-in protection includes reversebattery protection, reverse-current protection, internal
current limit with foldback and thermal limit with hysteresis.
The LT3045-1 is available in thermally enhanced 12-Lead
MSOP and 3mm × 3mm DFN packages.
nn
The device supplies 500mA at a typical 260mV dropout
voltage. Operating quiescent current is nominally 2.3mA
and drops to VVIOC + 0.5V
Control (VIOC) (Note 15)
VIOC Pin Voltage: VOUT ≤ 1.5V, VIN = 2.5V
%/W
1
V/V
1
4
1
VIOC Pin Source Current
l
VIOC Pin Sink Current: VIN ≥ 2.5V
l
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The EN/UV pin threshold must be met to ensure device operation.
Note 3: Maximum junction temperature limits operating conditions. The
regulated output voltage specification does not apply for all possible
combinations of input voltage and output current, especially due to the
internal current limit foldback which starts to decrease current limit at
VIN – VOUT > 12V. If operating at maximum output current, limit the input
voltage range. If operating at the maximum input voltage, limit the output
current range.
4
l
–0.01
V
V
200
µA
15
µA
Note 4: OUTS ties directly to OUT.
Note 5: Dropout voltage is the minimum input-to-output differential
voltage needed to maintain regulation at a specified output current. The
dropout voltage is measured when output is 1% out of regulation. This
definition results in a higher dropout voltage compared to hard dropout —
which is measured when VIN = VOUT(NOMINAL). For lower output voltages,
below 1.5V, dropout voltage is limited by the minimum input voltage
specification. Please consult the Typical Performance Characteristics
for curves of dropout voltage as a function of output load current and
temperature measured in a typical application circuit.
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
ELECTRICAL CHARACTERISTICS
Note 6: GND pin current is tested with VIN = VOUT(NOMINAL) and a current
source load. Therefore, the device is tested while operating in dropout. This
is the worst-case GND pin current. GND pin current decreases at higher
input voltages. Note that GND pin current does not include SET pin or ILIM
pin current but Quiescent current does include them.
Note 7: SET and OUTS pins are clamped using diodes and two 25Ω series
resistors. For less than 5ms transients, this clamp circuitry can carry
more than the rated current. Refer to Applications Information for more
information.
Note 8: Adding a capacitor across the SET pin resistor decreases output
voltage noise. Adding this capacitor bypasses the SET pin resistor’s
thermal noise as well as the reference current’s noise. The output noise
then equals the error amplifier noise. Use of a SET pin bypass capacitor
also increases start-up time.
Note 9: The LT3045-1 is tested and specified under pulsed load conditions
such that TJ ≈ TA. The LT3045-1E is 100% tested at 25°C and performance
is guaranteed from 0°C to 125°C. Specifications over the –40°C to 125°C
operating temperature range are assured by design, characterization, and
correlation with statistical process controls. The LT3045-1I is guaranteed
over the full –40°C to 125°C operating temperature range. High junction
temperatures degrade operating lifetimes. Operating lifetime is derated at
junction temperatures greater than 125°C.
Note 10: Parasitic diodes exist internally between the VIOC, ILIM, PG,
PGFB, SET, OUTS, and OUT pins and the GND pin. Do not drive these pins
more than 0.3V below the GND pin during a fault condition. These pins
must remain at a voltage more positive than GND during normal operation.
Note 11: The current limit programming scale factor is specified while the
internal backup current limit is not active. Note that the internal current
limit has foldback protection for VIN – VOUT differentials greater than 12V.
Note 12: The internal back-up current limit circuitry incorporates foldback
protection that decreases current limit for VIN – VOUT > 12V. Some level of
output current is provided at all VIN – VOUT differential voltages. Consult the
Typical Performance Characteristics graph for current limit vs VIN – VOUT.
Note 13: For output voltages less than 1V, the LT3045-1 requires a 10µA
minimum load current for stability.
Note 14: Maximum OUT-to-OUTS differential is guaranteed by design.
Note 15: The VIOC buffer outputs a voltage equal to VIN – VOUT or
VIN – 1.5V (for VOUT ≤ 1.5V). See Block Diagram and Applications
Information for further information. The VIOC pin’s source current should
be set between 10µA and 200µA.
30451fa
For more information www.linear.com/LT3045-1
5
LT3045-1
TYPICAL PERFORMANCE CHARACTERISTICS
SET Pin Current
101.0
2.0
N = 3250
100.4
100.2
100.0
99.8
99.6
99.4
98
0 25 50 75 100 125 150
TEMPERATURE (°C)
99
100
101
ISET DISTRIBUTION (µA)
1.0
0.5
0
–0.5
–1.0
30451 G01
Offset Voltage
30451 G02
SET Pin Current
Offset Voltage (VOUT – VSET)
2.0
SET PIN CURRENT (µA)
IL = 1mA
100.8 V
OUT = 1.3V
100.6
150°C
125°C
25°C
–55°C
100.4
100.2
100.0
99.8
99.6
99.4
99.0
2
2.0
100.0
99.8
99.6
99.4
6 8 10 12 14 16 18 20
INPUT VOLTAGE (V)
30451 G07
IL = 1mA
VIN = 20V
–1.0
–2.0
0
2
4
6 8 10 12 14 16 18 20
INPUT VOLTAGE (V)
30451 G06
0.20
20
V = 2.5V
18 ∆IIN= 1mA to 500mA
L
16 VOUT = 1.3V
150°C
125°C
25°C
–55°C
–0.5
0.18
0.16
14
0.14
12
0.12
10
0.10
VOS
8
0.08
0.06
6
–1.0
–2.0
4.5 6 7.5 9 10.5 12 13.5 15
OUTPUT VOLTAGE (V)
–0.5
Load Regulation
0
99.0
3
4
0.5
–1.5
1.5
2
1.0
99.2
0
0
4
0.04
ISET
0.02
2
0
1.5
3
4.5 6 7.5 9 10.5 12 13.5 15
OUTPUT VOLTAGE (V)
30451 G08
0
–75 –50 –25
∆ VOS (mV)
100.2
0.5
∆ISET (nA)
100.4
1.0
Offset Voltage (VOUT – VSET)
1.5
OFFSET VOLTAGE (mV)
100.6
150°C
125°C
25°C
–55°C
150°C
125°C
25°C
–55°C
30451 G05
SET Pin Current
IL = 1mA
VIN = 20V
0
30451 G04
101.0
100.8
IL = 1mA
VOUT = 1.3V
1.5
–1.5
99.2
–1
0
1
VOS DISTRIBUTION (mV)
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G03
101.0
N = 3250
–2
–2.0
–75 –50 –25
102
OFFSET VOLTAGE (mV)
99.0
–75 –50 –25
SET PIN CURRENT (µA)
VIN = 2V
IL = 1mA
VOUT = 1.3V
–1.5
99.2
6
Offset Voltage (VOUT – VSET)
1.5
OFFSET VOLTAGE (mV)
100.6
SET PIN CURRENT (µA)
SET Pin Current
VIN = 2V
IL = 1mA
VOUT = 1.3V
100.8
TJ = 25°C, unless otherwise noted.
0
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G09
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = 2V
VEN/UV = VIN
IL = 10µA
RSET = 13k
3.0
2.5
2.0
1.5
1.0
0.5
Quiescent Current
4.0
VEN/UV = 0V
45
QUIESCENT CURRENT (µA)
3.5
40
35
30
VIN = 20V
25
20
VIN = 2V
15
10
0
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
2.0
1.5
150°C
125°C
25°C
–55°C
0
1
4
300
250
200
150
150°C
125°C
25°C
–55°C
100
0
5
0
VIN = 5V
RSET = 33.2k
18
IL = 500mA
12
10
8
6
4
2
0
–75 –50 –25
IL = 300mA
IL = 100mA
300
30451 G16
IL = 1mA
200
150
100
0
–75 –50 –25
50 100 150 200 250 300 350 400 450 500
OUTPUT CURRENT (mA)
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G15
GND Pin Current
18
12
10
8
6
0
150°C
125°C
25°C
–55°C
0
RSET = 33.2k
16
14
2
0 25 50 75 100 125 150
TEMPERATURE (°C)
IL = 500mA
250
50
16
4
IL = 1mA
IL = 400mA
350
VIN = 4.3V
RSET = 33.2k
20
GND PIN CURRENT (mA)
GND PIN CURRENT (mA)
14
400
GND Pin Current
22
16
6 8 10 12 14 16 18 20
INPUT VOLTAGE (V)
30451 G14
GND Pin Current
18
4
RSET = 33.2k
450
350
30451 G13
20
2
Dropout Voltage
500
400
50
2
3
OUTPUT VOLTAGE (V)
0
30451 G12
DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
QUIESCENT CURRENT (mA)
2.5
0
0
RSET = 33.2k
450
3.0
0.5
1.0
Typical Dropout Voltage
500
VIN = 6V
VEN/UV = VIN
IL = 10µA
1.0
1.5
30451 G11
Quiescent Current
3.5
2.0
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G10
4.0
2.5
0.5
5
0
–75 –50 –25
VEN/UV = VIN
3.5 IL = 10µA
RSET = 33.2kΩ
3.0 IVIOC = 10µA
50 100 150 200 250 300 350 400 450 500
OUTPUT CURRENT (mA)
30451 G17
GND PIN CURRENT (mA)
QUIESCENT CURRENT (mA)
Quiescent Current
50
QUIESCENT CURRENT (mA)
Quiescent Current
4.0
TJ = 25°C, unless otherwise noted.
14
RL = 6.6Ω
12
10
RL = 11Ω
8
6
RL = 33Ω
4
RL = 330Ω
2
0
RL = 3.3kΩ
0
1
2
3 4 5 6 7
INPUT VOLTAGE (V)
8
9
10
30451 G18
30451fa
For more information www.linear.com/LT3045-1
7
LT3045-1
TYPICAL PERFORMANCE CHARACTERISTICS
EN/UV Turn-On Threshold
1.32
1.75
1.30
1.50
1.25
1.00
0.75
0.50
0
–75 –50 –25
185
1.28
1.26
1.24
VIN = 2V
1.22
VIN = 10V
1.20
RISING UVLO
FALLING UVLO
0.25
1.18
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
EN/UV PIN CURRENT (µA)
EN/UV PIN CURRENT (µA)
3.5
3.0
2.5
2.0
150°C
125°C
25°C
–55°C
0.5
0
2
4
8
7
6
5
VIN = 20V
4
3
2
0
6 8 10 12 14 16 18 20
ENABLE PIN VOLTAGE (V)
900
–30
–40
–50
–60
–70
–90
0
2
4
6 8 10 12 14 16 18 20
ENABLE PIN VOLTAGE (V)
–100
–20 –18 –16 –14 –12 –10 –8 –6 –4 –2
ENABLE PIN VOLTAGE (V)
Internal Current Limit
600
RILIM = 0Ω
VOUT = 0V
500
700
600
500
400
300
200
100
0
–20 –18 –16 –14 –12 –10 –8 –6 –4 –2
ENABLE PIN VOLTAGE (V)
0
30451 G25
VIN = 20V
RILIM = 0Ω
VOUT = 0V
400
300
200
100
VIN = 2.5V
VIN = 12V
0
–75 –50 –25
0
30451 G24
CURRENT LIMIT (mA)
CURRENT LIMIT (mA)
0.1
150°C
125°C
25°C
–55°C
–80
800
0.2
VIN = 2V
–20
Internal Current Limit
1000
150°C
125°C
25°C
–55°C
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G23
Input Pin Current
INPUT CURRENT (µA)
–10
1
0.3
8
80
Negative Enable Pin Current
VIN = 2V
30451 G22
VIN = 2V
VIN = 2V
95
0
9
4.5
1.0
110
30451 G21
EN/UV PIN CURRENT (µA)
VIN = 20V
1.5
125
EN/UV Pin Current
4.0
VIN = 10V
140
50
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
10
5.0
155
30451 G20
EN/UV Pin Current
5.5
170
65
30451 G19
0
EN/UV Pin Hysteresis
200
EN/UV PIN HYSTERESIS (mV)
2.00
TURN-ON THRESHOLD (V)
INPUT UVLO THRESHOLD (V)
Minimum Input Voltage
TJ = 25°C, unless otherwise noted.
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G26
0
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G27
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
TYPICAL PERFORMANCE CHARACTERISTICS
Internal Current Limit
Programmable Current Limit
1000
900
CURRENT LIMIT (mA)
CURRENT LIMIT (mA)
800
700
600
500
400
300
150°C
125°C
25°C
–55°C
200
100
0
RILIM = 300Ω
VOUT = 0V
600
500
400
300
100
VIN = 2.5V
VIN = 12V
0
–75 –50 –25
2 4 6 8 10 12 14 16 18 20
INPUT-TO-OUTPUT DIFFERENTIAL (V)
400
300
200
2.5VIN
5VIN
10VIN
100
60
0
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G30
PGFB Hysteresis
VIN = 2V
7
306
304
302
300
298
296
294
6
5
4
3
2
0
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G33
30451 G32
ISET During Start-Up with Fast
Start-Up Enabled
PG Pin Leakage Current
100
VIN = 2V
VPGFB = 290mV
IPG = 100µA
90
80
70
30
60
IPG (nA)
35
3.0
VPG = 2V
VPGFB = 310mV
2.5
50
40
15
30
10
20
5
10
0
–75 –50 –25
VIN = 2.5V
VPGFB = 290mV
VSET = 1.3V
2.0
ISET (mA)
50
30451 G34
VIN = 2V
1
290
–75 –50 –25
PG Output Low Voltage
0 25 50 75 100 125 150
TEMPERATURE (°C)
0 25 50 75 100 125 150
TEMPERATURE (°C)
8
30451 G31
20
VIN = 12V
20
292
50 100 150 200 250 300 350 400 450 500
OUTPUT CURRENT (mA)
25
VIN = 2.5V
80
PGFB HYSTERESIS (mV)
ILIM PIN CURRENT (uA)
500
PGFB RISING THRESHOLD (mV)
308
600
VPG (mV)
100
PGFB Rising Threshold
700
0
–75 –50 –25
120
310
VILIM = 0V
900 RSET = 13k
40
140
30451 G29
ILIM Pin Current
800
RILIM = 1.5k
VOUT = 0V
40
200
1000
45
160
700
30451 G28
0
180
CURRENT LIMIT (mA)
RILIM = 0Ω
800
0
Programmable Current Limit
200
1000
900
0
TJ = 25°C, unless otherwise noted.
1.5
1.0
0.5
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G35
0
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G36
30451fa
For more information www.linear.com/LT3045-1
9
LT3045-1
TYPICAL PERFORMANCE CHARACTERISTICS
Output Overshoot Recovery
Current Sink
3.5
12
VPGFB = 290mV
VSET = 1.3V
OUTPUT SINK CURRENT (mA)
3.0
ISET (mA)
2.5
2.0
1.5
1.0
0.5
0
0
2
6
4
2
VOUT Forced Above VOUT(NOMINAL)
0
5
100
60
20
7 8 9 10 11 12 13 14 15
OUTPUT VOLTAGE (V)
100
1k
10k 100k
FREQUENCY (Hz)
120
120
100
90
80
100
80
70
60
1k
10k 100k
FREQUENCY (Hz)
1M
10M
20
100
90
80
70
60
50
40
10
100
1k
10k 100k
FREQUENCY (Hz)
100kHz
500kHz
1MHz
2MHz
20
VOUT ≥ 1.3V
0.6V < VOUT < 1.3V
VOUT ≤ 0.6V
30
10
1M
10M
30451 G42
30
40
1M
Power Supply Ripple Rejection
50
VIN = 5V
RSET = 30.1k
COUT = 10µF
CSET = 0.47µF
30451 G43
10
10M
PSRR (dB)
PSRR (dB)
PSRR (dB)
100
10
1M
VIN = VOUT + 2V
IL = 500mA
COUT = 10µF
CSET = 0.47µF
110
20
VIN = 5V
RSET = 30.1k
30 CSET = 0.47µF
IL = 500mA
20
10
100
1k
10k 100k
FREQUENCY (Hz)
40
Power Supply Ripple Rejection
as a Function of Error Amplifier
Input Pair
Power Supply Ripple Rejection
40
60
50
VIN = 5V
RSET = 30.1k
COUT = 10µF
IL = 500mA
10
70
30451 G41
140
IL = 500mA
IL = 300mA
IL = 100mA
IL = 50mA
IL = 1mA
100
80
70
COUT = 10µF
COUT = 22µF
110
80
30451 G40
60
Power Supply Ripple Rejection
90
30
6
0 25 50 75 100 125 150
TEMPERATURE (°C)
30451 G39
90
40
5
2
30451 G38
CSET = 4.7µF
CSET = 0.47µF
50
4
3
120
110
2
0
4
Power Supply Ripple Rejection
PSRR (dB)
CURRENT (mA)
4
5
0
–75 –50 –25
20
120
IIN WHEN VEN = 0V
IOUT WHEN VEN = 0V
IIN WHEN VEN = VIN
IOUT WHEN VEN = VIN
6
10
15
VOUT – VSET (mV)
PSRR (dB)
VIN = 5V
RSET = 33.2k
VIN = 5V
RSET = 33.2k
VOUT – VSET > 5mV
6
1
30451 G37
8
150°C
125°C
25°C
–55°C
8
0
4 6 8 10 12 14 16 18 20
VIN-TO-VSET DIFFERENTIAL (V)
7
VIN = 5V
RSET = 33.2k
10
Output Overshoot Recovery
Current Sink
OUTPUT SINK CURRENT (mA)
ISET During Start-Up with Fast
Start-Up Enabled
TJ = 25°C, unless otherwise noted.
10M
30451 G44
0
0
IL = 500mA
RSET = 30.1k
COUT = 10µF
CSET = 0.47µF
1
2
3
4
INPUT–TO–OUTPUT DIFFERENTIAL (V)
5
30451 G45
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
TYPICAL PERFORMANCE CHARACTERISTICS
Integrated RMS Output Noise
(10Hz to 100kHz)
Integrated RMS Output Noise
(10Hz to 100kHz)
2.0
9
VIN = 5V
RSET = 33.2k
1.6 COUT = 10µF
CSET = 4.7µF
1.4
1.8
VIN = 5V
COUT = 10µF
RSET = 33.2k
ILOAD = 500mA
8
RMS OUTPUT NOISE (µVRMS)
1.2
1.0
0.8
0.6
0.4
7
6
5
4
3
2
1
0.2
0
0.1
1
10
SET PIN CAPACITANCE (µF)
Noise Spectral Density
1.0
0.8
0.6
0.4
CSET = 0.047µF
CSET = 0.47µF
CSET = 1µF
CSET = 4.7µF
CSET = 22µF
10
1M
10M
30451 G49
0
1.5
3
4.5 6 7.5 9 10.5 12 13.5 15
OUTPUT VOLTAGE (V)
30451 G48
Noise Spectral Density
OUTPUT NOISE (nV/√Hz)
OUTPUT NOISE (nV/√Hz)
1.2
30451 G47
1000
1 V = 5V
IN
RSET = 33.2k
COUT = 10µF
ILOAD = 500mA
0.1
10
100
1k
10k 100k
FREQUENCY (Hz)
1.4
0
100
30451 G46
100
1.6
0.2
0
0.01
50 100 150 200 250 300 350 400 450 500
LOAD CURRENT (mA)
VIN = VOUT + 2V
COUT = 10µF
CSET = 4.7µF
ILOAD = 500mA
1.8
Noise Spectral Density
1000
1000
100
100
10
COUT = 10µF
1 V = 5V
IN
RSET = 33.2k
COUT = 22µF
CSET = 4.7µF
ILOAD = 500mA
0.1
10
100
1k
10k 100k
1M
FREQUENCY (Hz)
10M
OUTPUT NOISE (nV/√Hz)
RMS OUTPUT NOISE (µVRMS)
Integrated RMS Output Noise
(10Hz to 100kHz)
RMS OUTPUT NOISE (µVRMS)
2.0
0
TJ = 25°C, unless otherwise noted.
IL = 500mA
IL = 300mA
IL = 100mA
IL = 10mA
IL = 1mA
10
1 V = 5V
IN
RSET = 33.2k
CSET = 4.7µF
COUT = 10µF
0.1
10
100
1k
10k 100k
FREQUENCY (Hz)
10M
30451 G51
30451 G50
Noise Spectral Density as
a Function of Error Amplifier
Input Pair
1M
Output Noise: 10Hz to 100kHz
Load Transient Response
OUTPUT NOISE (nV/√Hz)
1000
100
VOUT ≥ 1.3V
0.6V < VOUT < 1.3V
VOUT ≤ 0.6V
OUTPUT
CURRENT
500mA/DIV
5µV/DIV
VIN = 5V
RSET = 33.2k
COUT = 10µF
CSET = 4.7µF
IL = 500mA
10
1 V =V
IN
OUT + 2V
IL = 500mA
COUT = 10µF
CSET = 4.7µF
0.1
10
100
1k
10k 100k
FREQUENCY (Hz)
OUTPUT
VOLTAGE
20mV/DIV
1ms/DIV
1M
30451 G53
10M
30451 G52
20µs/DIV
VIN = 5V
RSET = 33.2k
COUT = 10µF
CSET = 0.47µF
LOAD STEP = 10mA TO 500mA
30451 G54
30451fa
For more information www.linear.com/LT3045-1
11
LT3045-1
TYPICAL PERFORMANCE CHARACTERISTICS
TJ = 25°C, unless otherwise noted.
Start-Up Time with and
without Fast Start-Up Circuitry for
Large CSET
Line Transient Response
Input Supply Ramp-Up and
Ramp-Down
500mV/DIV
INPUT VOLTAGE
OUTPUT WITH
FAST START–UP
(SET AT 90%)
INPUT
VOLTAGE
500mV/DIV
2V/DIV
OUTPUT
VOLTAGE
1mV/DIV
PULSE EN/UV
OUTPUT WITHOUT
FAST START–UP
30451 G55
5µs/DIV
VIN = 5V
RSET = 33.2k
COUT = 10µF
CSET = 4.7µF
RL = 6.6Ω
VIN = 4.5V TO 5V
RSET = 33.2k
COUT = 10µF
CSET = 0.47µF
IL = 500mA
VIOC VOLTAGE (V)
1.06
1.04
VIN = 4.3V
VOUT = 3.3V
IOUT = 1mA
1.08
1.06
1.02
1.00
0.98
0.96
1.04
1.02
1.00
0.98
0.96
0.94
0.94
0.92
0.92
0.90
0 25 50 75 100 125 150
TEMPERATURE (°C)
150°C
125°C
25°C
–55°C
0
25
50 75 100 125 150 175 200
VIOC SOURCE CURRENT (µA)
30451 G58
30451 G59
VIOC Sink Current
VIOC SINK CURRENT (µA)
–18
–16
–14
VIOC Voltage
1.10
VIN = 4.3V
VOUT = 3.3V
VVIOC = 2V
IOUT = 1mA
1.06
–12
–10
–8
–6
1.04
1.02
1.00
0.98
0.96
–4
0.94
–2
0.92
0
–75 –50 –25
VIN = 4.3V
VOUT = 3.3V
IVIOC = 100µA
1.08
VIOC VOLTAGE (V)
–20
0 25 50 75 100 125 150
TEMPERATURE (°C)
0.90
150°C
125°C
25°C
–55°C
0
50 100 150 200 250 300 350 400 450 500
OUTPUT LOAD CURRENT (mA)
30451 G60
12
30451 G57
VIOC Voltage
1.10
VIN = 4.3V
VOUT = 3.3V
IVIOC = 100µA
IOUT = 1mA
0.90
–75 –50 –25
50ms/DIV
VIN = 0V TO 5V
VEN/UV = VIN
RSET = 33.2k
COUT = 10µF
CSET = 0.47µF
RL = 6.6Ω
VIOC VOLTAGE (V)
1.08
OUTPUT VOLTAGE
30451 G56
100ms/DIV
VIOC Voltage
1.10
2V/DIV
30451 G61
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
PIN FUNCTIONS
IN (Pins 1, 2): Input. These pins supply power to the
regulator. The LT3045-1 requires a bypass capacitor at the
IN pin. In general, a battery’s output impedance rises with
frequency, so include a bypass capacitor in battery-powered
applications. While a 4.7µF input bypass capacitor generally suffices, applications with large load transients may
require higher input capacitance to prevent input supply
droop. Consult the Applications Information section on the
proper use of an input capacitor and its effect on circuit
performance, in particular PSRR. The LT3045-1 withstands
reverse voltages on IN with respect to GND, OUTS and OUT.
In the case of a reversed input, which occurs if a battery
is plugged-in backwards, the LT3045-1 acts as if a diode
is in series with its input. Hence, no reverse-current flows
into the LT3045-1 and no negative voltage appears at the
load. The device protects itself and the load.
VIOC (Pin 3): Voltage for Input-to-Output Control. The
LT3045-1 incorporates a tracking function to control the
switching pre-regulator powering the LT3045-1. The VIOC
pin is the output of this tracking function that drives the preregulator’s feedback (FB) pin to maintain the LT3045-1’s
input voltage at VOUT + VVIOC. This function minimizes
power dissipation while maintaining PSRR performance.
See Applications Information section for details.
EN/UV (Pin 4): Enable/UVLO. Pulling the LT3045-1’s EN/
UV pin low places the part in shutdown. Quiescent current
in shutdown drops to less than 1µA and the output voltage turns off. Alternatively, the EN/UV pin can set an input
supply undervoltage lockout (UVLO) threshold using a
resistor divider between IN, EN/UV and GND. The LT3045-1
typically turns on when the EN/UV voltage exceeds 1.24V
on its rising edge, with a 130mV hysteresis on its falling
edge. The EN/UV pin can be driven above the input voltage
and maintain proper functionality. If unused, tie EN/UV to
IN. Do not float the EN/UV pin.
PG (Pin 5): Power Good. PG is an open-collector flag that
indicates output voltage regulation. PG pulls low if PGFB
is below 300mV. If the power good functionality is not
needed, float the PG pin. A parasitic substrate diode exists
between PG and GND pins of the LT3045-1; do not drive
PG more than 0.3V below GND during normal operation
or during a fault condition.
ILIM (Pin 6): Current Limit Programming Pin. Connecting a
resistor between ILIM and GND programs the current limit.
For best accuracy, Kelvin connect this resistor directly to
the LT3045-1’s GND pin. The programming scale factor
is nominally 150mA•kΩ. The ILIM pin sources current
proportional (1:500) to output current; therefore, it also
serves as a current monitoring pin with a 0V to 300mV
range. If the programmable current limit functionality is
not needed, tie ILIM to GND. A parasitic substrate diode
exists between ILIM and GND pins of the LT3045-1; do
not drive ILIM more than 0.3V below GND during normal
operation or during a fault condition.
PGFB (Pin 7): Power Good Feedback. The PG pin pulls
high if PGFB increases beyond 300mV on its rising edge,
with 7mV hysteresis on its falling edge. Connecting an
external resistor divider between OUT, PGFB and GND
sets the programmable power good threshold with the
following transfer function: 0.3V • (1 + RPG2/RPG1). As
discussed in the Applications Information section, PGFB
also activates the fast start-up circuitry. Tie PGFB to IN
if power good and fast start-up functionalities are not
needed, and if reverse input protection is additionally
required, tie the anode of a 1N4148 diode to IN and its
cathode to PGFB. See the Typical Applications section for
details. A parasitic substrate diode exists between PGFB
and GND pins of the LT3045-1; do not drive PGFB more
than 0.3V below GND during normal operation or during
a fault condition.
SET (Pin 8): SET. This pin is the inverting input of the error amplifier and the regulation set-point for the LT30451. SET sources a precision 100µA current that flows
through an external resistor connected between SET and
GND. The LT3045-1’s output voltage is determined by
VSET = ISET • RSET. Output voltage range is from zero to
15V. Adding a capacitor from SET to GND improves noise,
PSRR and transient response at the expense of increased
start-up time. For optimum load regulation, Kelvin connect the ground side of the SET pin resistor directly to
the load. A parasitic substrate diode exists between SET
and GND pins of the LT3045-1; do not drive SET more
than 0.3V below GND during normal operation or during
a fault condition.
30451fa
For more information www.linear.com/LT3045-1
13
LT3045-1
PIN FUNCTIONS
GND (Pin 9, Exposed Pad Pin 13): Ground. The exposed
backside is an electrical connection to GND. To ensure
proper electrical and thermal performance, solder the
exposed backside to the PCB ground and tie it directly
to the GND pin.
OUTS (Pin 10): Output Sense. This pin is the noninverting input to the error amplifier. For optimal transient
performance and load regulation, Kelvin connect OUTS
directly to the output capacitor and the load. Also, tie the
GND connections of the output capacitor and the SET pin
capacitor directly together. A parasitic substrate diode
exists between OUTS and GND pins of the LT3045-1; do
not drive OUTS more than 0.3V below GND during normal
operation or during a fault condition.
14
OUT (Pins 11, 12): Output. These pins supply power to the
load. For stability, use a minimum 10µF output capacitor
with an ESR below 20mΩ and an ESL below 2nH. Large
load transients require larger output capacitance to limit
peak voltage transients. Refer to the Applications Information section for more information on output capacitance. A
parasitic substrate diode exists between OUT and GND pins
of the LT3045-1; do not drive OUT more than 0.3V below
GND during normal operation or during a fault condition.
30451fa
For more information www.linear.com/LT3045-1
V
V
–
+
–
+
300mV
1.24V
7
BIAS
For more information www.linear.com/LT3045-1
RPG1
RPG2
PGFB
+
–
PROGRAMMABLE
POWER GOOD
+
–
ENABLE
COMPARATOR
2mA
5
RPG
PG
FAST START-UP
DISABLE LOGIC
AV = 1
VIOC
– – +
1.5V
INPUT-TOOUTPUT
CONTROL
3
GND
9, 13
INPUT UVLO
CURRENT LIMIT
THERMAL SHDN
DROPOUT
FAST START-UP
CURRENT
REFERENCE
8
RSET
SET
CSET
SET-TO-OUTS
PROTECTION
CLAMP
INPUT
UVLO
THERMAL
SHDN
100µA
OUTS
10
V
ERROR
AMPLIFIER
–
–
300mV
V
–
+
300mV
PROGRAMMABLE
CURRENT LIMIT
V
+
INTERNAL CURRENT
LIMIT
1.5V
+
–
+
OUTPUT OVERSHOOT
RECOVERY
DRIVER
–
+
EN/UV
–
+
+
–
4
6
215Ω
QC
OUT
QPWR
11, 12
RILIM
ILIM
QP
IN
1, 2
VIN
30451 BD
COUT
CIN
VOUT
RL
LT3045-1
BLOCK DIAGRAM
30451fa
15
LT3045-1
APPLICATIONS INFORMATION
The LT3045-1 is a high performance low dropout linear
regulator featuring LTC’s ultralow noise (2nV/√Hz at
10kHz) and ultrahigh PSRR (76dB at 1MHz) architecture
for powering noise sensitive applications. Designed as a
precision current source followed by a high performance
rail-to-rail voltage buffer, the LT3045-1 can be easily paralleled to further reduce noise, increase output current and
spread heat on the PCB. The device additionally features
programmable current limit, fast start-up capability and
programmable power good.
The LT3045-1 is easy to use and incorporates all of the
protection features expected in high performance regulators. Included are short-circuit protection, safe operating
area protection, reverse-battery protection, reverse-current
protection, and thermal shutdown with hysteresis.
In addition to the LT3045 feature set, the LT3045-1 incorporates a VIOC tracking function to control an upstream
switching converter to maintain a constant voltage across
the LT3045-1 and hence minimize power dissipation.
Output Voltage
The LT3045-1 incorporates a precision 100µA current
source flowing out of the SET pin, which also ties to the
error amplifier’s inverting input. Figure 1 illustrates that
connecting a resistor from SET to ground generates a reference voltage for the error amplifier. This reference voltage
is simply the product of the SET pin current and the SET
pin resistor. The error amplifier’s unity-gain configuration
produces a low impedance version of this voltage on its
noninverting input, i.e. the OUTS pin, which is externally
tied to the OUT pin.
VIN
5V ±5%
4.7µF
LT3045-1
IN
100µA
–
+
EN/UV
OUT
PGFB
VOUT, 3.3V
IOUT(MAX), 500mA
OUTS
VIOC
SET
GND ILIM
10µF
PG
30451 F01
0.47µF
33.2k
Figure 1. Basic Adjustable Regulator
16
The LT3045-1’s rail-to-rail error amplifier and current
reference allows for a wide output voltage range from 0V
(using a 0Ω resistor) to VIN minus dropout — up to 15V.
A PNP-based input pair is active for 0V to 0.6V output
and an NPN-based input pair is active for output voltages greater than 1.3V, with a smooth transition between
the two input pairs from 0.6V to 1.3V output. While the
NPN-based input pair is designed to offer the best overall
performance, refer to the Electrical Characteristics Table for
details on offset voltage, SET pin current, output noise and
PSRR variation with the error amp input pair. Table 1 lists
many common output voltages and their corresponding
1% RSET resistors.
Table 1. 1% Resistor for Common Output Voltages
VOUT (V)
RSET (kΩ)
2.5
24.9
3.3
33.2
5
49.9
12
121
15
150
The benefit of using a current reference compared with a
voltage reference as used in conventional regulators is that
the regulator always operates in unity gain configuration,
independent of the programmed output voltage. This allows the LT3045-1 to have loop gain, frequency response
and bandwidth independent of the output voltage. As a
result, noise, PSRR and transient performance do not
change with output voltage. Moreover, since none of the
error amp gain is needed to amplify the SET pin voltage
to a higher output voltage, output load regulation is more
tightly specified in the hundreds of microvolts range and
not as a fixed percentage of the output voltage.
Since the zero TC current source is highly accurate, the
SET pin resistor can become the limiting factor in achieving high accuracy. Hence, it should be a precision resistor.
Additionally, any leakage paths to or from the SET pin
create errors in the output voltage. If necessary, use high
quality insulation (e.g., Teflon, Kel-F); moreover, cleaning of all insulating surfaces to remove fluxes and other
residues may be required. High humidity environments
may require a surface coating at the SET pin to provide
a moisture barrier.
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
APPLICATIONS INFORMATION
Minimize board leakage by encircling the SET pin with a
guard ring operated at a potential close to itself — ideally
tied to the OUT pin. Guarding both sides of the circuit
board is recommended. Bulk leakage reduction depends
on the guard ring width. Leakages of 100nA into or out of
the SET pin creates a 0.1% error in the reference voltage.
Leakages of this magnitude, coupled with other sources
of leakage, can cause significant errors in the output voltage, especially over wide operating temperature range.
Figure 2 illustrates a typical guard ring layout technique.
VIN
100µA
CIN
EN/UV
PGFB
12
2
11
3
10
4
13
VIOC
5
8
7
DEMO BOARD
PCB LAYOUT
ILLUSTRATES
4-TERMINAL
CONNECTION
TO COUT
VOUT
IOUT(MAX): 500mA
OUTS
SET
GND
COUT
ILIM
CSET
30451 F03
OUT
Figure 3. COUT and CSET Connections for Best Performance
9
6
OUT
PG
RSET
1
LT3045-1
IN
SET
30451 F02
Figure 2. DFN Guard Ring Layout
Since the SET pin is a high impedance node, unwanted
signals may couple into the SET pin and cause erratic
behavior. This is most noticeable when operating with a
minimum output capacitor at heavy load currents. Bypassing the SET pin with a small capacitance to ground
resolves this issue — 10nF is sufficient.
Figure 3, minimize the effects of PCB trace and solder
inductance by tying the OUTS pin directly to COUT and
the GND side of CSET directly to the GND side of COUT,
as well as keep the GND sides of CIN and COUT reasonably
close. Refer to the LT3045-1 demo board manual for more
information on the recommended layout that meets these
requirements. While the LT3045-1 is robust enough not
to oscillate if the recommended layout is not followed,
depending on the actual layout, phase/gain margin, noise
and PSRR performance may degrade.
For applications requiring higher accuracy or an adjustable output voltage, the SET pin may be actively driven
by an external voltage source capable of sinking 100µA.
Connecting a precision voltage reference to the SET pin
eliminates any errors present in the output voltage due
to the reference current and SET pin resistor tolerances.
Stability and Output Capacitance
Output Sensing and Stability
Given the high PSRR and low noise performance attained
using a single 10µF ceramic output capacitor, larger values
of output capacitor only marginally improves the performance because the regulator bandwidth decreases with
increasing output capacitance — hence, there is little to
be gained by using larger than the minimum 10µF output
capacitor. Nonetheless, larger values of output capacitance
do decrease peak output deviations during a load transient.
Note that bypass capacitors used to decouple individual
components powered by the LT3045-1 increase the effective output capacitance.
The LT3045-1’s OUTS pin provides a Kelvin sense connection to the output. The SET pin resistor’s GND side
provides a Kelvin sense connection to the load’s GND side.
Additionally, for ultrahigh PSRR, the LT3045-1 bandwidth
is made quite high (~1MHz), making it very close to a
typical 10µF (1206 case size) ceramic output capacitor’s
self-resonance frequency (~1.6MHz). Therefore, it is very
important to avoid adding extra impedance (ESR and
ESL) outside the feedback loop. To that end, as shown in
The LT3045-1 requires an output capacitor for stability.
Given its high bandwidth, LTC recommends low ESR and
ESL ceramic capacitors. A minimum 10µF output capacitance with an ESR below 20mΩ and an ESL below 2nH is
required for stability.
30451fa
For more information www.linear.com/LT3045-1
17
LT3045-1
APPLICATIONS INFORMATION
X5R and X7R dielectrics result in more stable characteristics and are thus more suitable for LT3045-1. The X7R
dielectric has better stability across temperature, while the
X5R is less expensive and is available in higher values.
Nonetheless, care must still be exercised when using
X5R and X7R capacitors. The X5R and X7R codes only
specify operating temperature range and the maximum
capacitance change over temperature. While capacitance
change due to DC bias for X5R and X7R is better than
Y5V and Z5U dielectrics, it can still be significant enough
to drop capacitance below sufficient levels. As shown in
Figure 6, capacitor DC bias characteristics tend to improve
as component case size increases, but verification of
expected capacitance at the operating voltage is highly
recommended. Due to its good voltage coefficient in small
case sizes, LTC recommends using Murata’s GJ8 series
ceramic capacitors.
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
0
CHANGE IN VALUE (%)
X5R
–20
–40
–60
Y5V
–80
–100
0
2
4
14
6
12
8 10
DC BIAS VOLTAGE (V)
16
30451 F04
Figure 4. Ceramic Capacitor DC Bias Characteristics
40
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
20
X5R
0
–20
–40
Y5V
–60
–80
–100
–50
–25
0
25
75
50
TEMPERATURE (°C)
100
125
30451 F05
Figure 5. Ceramic Capacitor Temperature Characteristics
20
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress upon
it, similar to how a piezoelectric microphone works. For a
ceramic capacitor, this stress can be induced by mechanical
vibrations within the system or due to thermal transients.
LT3045-1 applications in high vibration environments
have three distinct piezoelectric noise generators: ceramic
output, input, and SET pin capacitors. However, due to
LT3045-1’s very low output impedance over a wide frequency range, negligible output noise is generated using
CHANGE IN VALUE (%)
0
High Vibration Environments
18
20
CHANGE IN VALUE (%)
Give extra consideration to the type of ceramic capacitors
used. They are manufactured with a variety of dielectrics,
each with different behavior across temperature and applied
voltage. The most common dielectrics used are specified
with EIA temperature characteristic codes of Z5U, Y5V,
X5R and X7R. The Z5U and Y5V dielectrics are good for
providing high capacitance in the small packages, but they
tend to have stronger voltage and temperature coefficients
as shown in Figure 4 and Figure 5. When used with a 5V
regulator, a 16V 10µF Y5V capacitor can exhibit an effective
value as low as 1µF to 2µF for the DC bias voltage applied
over the operating temperature range.
–20
–40
–60
–80
–100
MURATA: 25V,10%,
X7R/X5R, 10µF CERAMIC
1
5
10
15
DC BIAS (V)
25
20
30451 F06
GRM SERIES, 0805, 1.45mm THICK
GRM SERIES, 1206, 1.8mm THICK
GRM SERIES, 1210, 2.2mm THICK
GJ8 SERIES, 1206, 1.9mm THICK
Figure 6. Capacitor Voltage Coefficient for Different Case Sizes
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
APPLICATIONS INFORMATION
a ceramic output capacitor. Similarly, due to LT3045-1’s
ultrahigh PSRR, negligible output noise is generated
using a ceramic input capacitor. Nonetheless, given the
high SET pin impedance, any piezoelectric response
from a ceramic SET pin capacitor generates significant
output noise – peak-to-peak excursions of hundreds of
µVs. However, due to the SET pin capacitor’s high ESR
and ESL tolerance, any non-piezoelectrically responsive
(tantalum, electrolytic, or film) capacitor can be used at
the SET pin – although electrolytic capacitors tend to
have high 1/f noise. In any case, use of a surface mount
capacitor is highly recommended.
Stability and Input Capacitance
The LT3045-1 is stable with a minimum 4.7µF IN pin capacitor. LTC recommends using low ESR ceramic capacitors.
In cases where long wires connect the power supply to
the LT3045-1’s input and ground terminals, the use of low
value input capacitors combined with a large load current
can result in instability. The resonant LC tank circuit formed
by the wire inductance and the input capacitor is the cause
and not because of LT3045-1’s instability.
The self-inductance, or isolated inductance, of a wire
is directly proportional to its length. The wire diameter,
however, has less influence on its self-inductance. For
example, the self-inductance of a 2-AWG isolated wire
with a diameter of 0.26" is about half the inductance of a
30-AWG wire with a diameter of 0.01". One foot of 30-AWG
wire has 465nH of self-inductance.
Several methods exist to reduce a wire’s self-inductance.
One method divides the current flowing towards the
LT3045-1 between two parallel conductors. In this case,
placing the wires further apart reduces the inductance; up
to a 50% reduction when placed only a few inches apart.
Splitting the wires connect two equal inductors in parallel.
However, when placed in close proximity to each other,
their mutual inductance adds to the overall self inductance
of the wires — therefore a 50% reduction is not possible
in such cases. The second and more effective technique
to reduce the overall inductance is to place the forward
and return current conductors (the input and ground
wires) in close proximity. Two 30-AWG wires separated
by 0.02" reduce the overall inductance to about one-fifth
of a single wire.
If a battery mounted in close proximity powers the LT30451, a 4.7µF input capacitor suffices for stability. However,
if a distantly located supply powers the LT3045-1, use a
larger value input capacitor. Use a rough guideline of 1µF
(in addition to the 4.7µF minimum) per 6" of wire length.
The minimum input capacitance needed to stabilize the
application also varies with the output capacitance as
well as the load current. Placing additional capacitance
on the LT3045-1’s output helps. However, this requires
significantly more capacitance compared to additional input
bypassing. Series resistance between the supply and the
LT3045-1 input also helps stabilize the application; as little
as 0.1Ω to 0.5Ω suffices. This impedance dampens the
LC tank circuit at the expense of dropout voltage. A better
alternative is to use a higher ESR tantalum or electrolytic
capacitor at the LT3045-1 input in parallel with a 4.7µF
ceramic capacitor.
PSRR and Input Capacitance
For applications utilizing the LT3045-1 for post-regulating
switching converters, placing a capacitor directly at the
LT3045-1 input results in AC current (at the switching
frequency) to flow near the LT3045-1. This relatively highfrequency switching current generates a magnetic field
that couples to the LT3045-1 output, thereby degrading its
effective PSRR. While highly dependent on the PCB, the
switching pre-regulator, the input capacitance, amongst
other factors, the PSRR degradation can be easily over
30dB at 1MHz. This degradation is present even if the
LT3045-1 is de-soldered from the board, because it effectively degrades the PSRR of the PC board itself. While
negligible for conventional low PSRR LDOs, LT3045-1’s
ultrahigh PSRR requires careful attention to higher order
parasitics in order to extract the full performance offered
by the regulator.
To mitigate the flow of high-frequency switching current
near the LT3045-1, the LT3045-1 input capacitor can be
entirely removed -- as long as the switching converter’s
output capacitor is located more than an inch away from
the LT3045-1. Magnetic coupling rapidly decreases with
increasing distance. Nonetheless, if the switching pre30451fa
For more information www.linear.com/LT3045-1
19
LT3045-1
APPLICATIONS INFORMATION
regulator is placed too far away (conservatively more
than a couple inches) from the LT3045-1, with no input
capacitor present, as with any regulator, the LT3045-1
input will oscillate at the parasitic LC resonance frequency.
Besides, it is generally a very common (and a preferred)
practice to bypass regulator input with some capacitance.
So this option is fairly limited in its scope and not the most
palatable solution.
To that end, LTC recommends using the LT3045-1 demo
board layout for achieving the best possible PSRR performance. The LT3045-1 demo board layout utilizes magnetic
field cancellation techniques to prevent PSRR degradation
caused by this high-frequency current flow—while utilizing
the input capacitor.
Filtering High Frequency Spikes
For applications where the LT3045-1 is used to postregulate a switching converter, its high PSRR effectively
suppresses any “noise” present at the switcher’s switching
frequency — typically 100kHz to 4MHz. However, the very
high frequency (hundreds of MHz) “spikes” — beyond the
LT3045-1’s bandwidth — associated with the switcher’s
power switch transition times will almost directly pass
through the LT3045-1. While the output capacitor is partly
intended to absorb these spikes, its ESL will limit its ability
at these frequencies. A ferrite bead or even the inductance
associated with a short (e.g. 0.5”) PCB trace between the
switcher’s output and the LT3045-1’s input can serve as
an LC-filter to suppress these very high frequency spikes.
Output Noise
The LT3045-1 offers many advantages with respect to
noise performance. Traditional linear regulators have
several sources of noise. The most critical noise sources
for a traditional regulator are its voltage reference, error
amplifier, noise from the resistor divider network used for
setting output voltage and the noise gain created by this
resistor divider. Many low noise regulators pin out their
voltage reference to allow for noise reduction by bypassing
the reference voltage.
Unlike most linear regulators, the LT3045-1 does not use
a voltage reference; instead, it uses a 100µA current reference. The current reference operates with typical noise
20
current level of 20pA/√Hz (6nARMS over a 10Hz to 100kHz
bandwidth). The resultant voltage noise equals the current
noise multiplied by the resistor value, which in turn is RMS
summed with the error amplifier’s noise and the resistor’s
own noise of √4kTR — whereby k = Boltzmann’s constant
1.38 • 10–23J/K and T is the absolute temperature.
One problem that conventional linear regulators face is
that the resistor divider setting the output voltage gains up
the reference noise. In contrast, the LT3045-1’s unity-gain
follower architecture presents no gain from the SET pin
to the output. Therefore, if a capacitor bypasses the SET
pin resistor, then the output noise is independent of the
programmed output voltage. The resultant output noise
is then set just by the error amplifier’s noise — typically
2nV/√Hz from 10kHz to 1MHz and 0.8µVRMS in a 10Hz
to 100kHz bandwidth using a 4.7µF SET pin capacitor.
Paralleling multiple LT3045-1s further reduces noise by
√N, for N parallel regulators.
Refer to the Typical Performance Characteristics section
for noise spectral density and RMS integrated noise over
various load currents and SET pin capacitances.
Set Pin (Bypass) Capacitance: Noise, PSRR, Transient
Response and Soft-Start
In addition to reducing output noise, using a SET pin bypass
capacitor also improves PSRR and transient performance.
Note that any bypass capacitor leakage deteriorates the
LT3045-1’s DC regulation. Capacitor leakage of even 100nA
is a 0.1% DC error. Therefore, LTC recommends the use
of a good quality low leakage ceramic capacitor.
Using a SET pin bypass capacitor also soft-starts the output
and limits inrush current. The RC time constant, formed
by the SET pin resistor and capacitor, controls soft-start
time. Ramp-up rate from 0 to 90% of nominal VOUT is:
tSS ≈ 2.3 • RSET • CSET (Fast Start-Up Disabled)
Fast Start-Up
For ultralow noise applications that require low 1/f noise
(i.e. at frequencies below 100Hz), a larger value SET pin
capacitor is required, up to 22µF. While this would normally
significantly increase the regulator’s start-up time, the
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
APPLICATIONS INFORMATION
LT3045-1 incorporates fast start-up circuitry that increases
the SET pin current to about 2mA during start-up.
As shown in the Block Diagram, the 2mA current source
remains engaged while PGFB is below 300mV, unless the
regulator is in current limit, dropout, thermal shutdown
or input voltage is below minimum VIN.
If fast start-up capability is not used, tie PGFB to IN or to
OUT for output voltages above 300mV. Note that doing
so also disables power good functionality.
ENABLE/UVLO
The EN/UV pin is used to put the regulator into a micropower shutdown state. The LT3045-1 has an accurate
1.24V turn-on threshold on the EN/UV pin with 130mV
of hysteresis. This threshold can be used in conjunction
with a resistor divider from the input supply to define an
accurate undervoltage lockout (UVLO) threshold for the
regulator. The EN/UV pin current (IEN) at the threshold from
the Electrical Characteristics table needs to be considered
when calculating the resistor divider network:
⎛ R ⎞
VIN(UVLO) =1.24V • ⎜1+ EN2 ⎟ +IEN •REN2
⎝ REN1 ⎠
The EN/UV pin current (IEN) can be ignored if REN1 is less
than 100k. If unused, tie EN/UV pin to IN.
Programmable Power Good
As illustrated in the Block Diagram, power good threshold is user programmable using the ratio of two external
resistors, RPG2 and RPG1:
⎛ R ⎞
VOUT(PG _ THRESHOLD) = 0.3V • ⎜1+ PG2 ⎟ +IPGFB •RPG2
⎝ RPG1 ⎠
If the PGFB pin increases above 300mV, the open-collector
PG pin de-asserts and becomes high impedance. The
power good comparator has 7mV hysteresis and 5µs of
deglitching. The PGFB pin current (IPGFB) from the Electrical
Characteristics table must be considered when determining
the resistor divider network. The PGFB pin current (IPGFB)
can be ignored if RPG1 is less than 30k. If power good
functionality is not used, float the PG pin. Please note that
programmable power good and fast start-up capabilities
are disabled for output voltages below 300mV.
Externally Programmable Current Limit
The ILIM pin’s current limit threshold is 300mV. Connecting
a resistor from ILIM to GND sets the maximum current
flowing out of the ILIM pin, which in turn programs the
LT3045-1’s current limit. With a 150mA • kΩ programming
scale factor, the current limit can be calculated as follows:
Current Limit =
150mA •kΩ
RILIM
For example, a 1kΩ resistor programs the current limit
to 150mA and a 2kΩ resistor programs the current limit
to 75mA. For good accuracy, Kelvin connect this resistor
to the LT3045-1’s GND pin.
In cases where IN-to-OUT differential is greater than 12V,
the LT3045-1’s foldback circuitry decreases the internal
current limit. As a result, internal current limit may override the externally programmed current limit level to keep
the LT3045-1 within its safe-operating-area (SOA). See
the Internal Current Limit vs Input-to-Output Differential
graph in the Typical Performance Characteristics section.
As shown in the Block Diagram, the ILIM pin sources current
proportional (1:500) to output current; therefore, it also
serves as a current monitoring pin with a 0V to 300mV
range. If external current limit or current monitoring is
not used, tie ILIM to GND.
Output Overshoot Recovery
During a load step from full load to no load (or light
load), the output voltage overshoots before the regulator
responds to turn the power transistor OFF. Given that there
is no load (or very light load) present at the output, it takes
a long time to discharge the output capacitor.
As illustrated in the Block Diagram, the LT3045-1 incorporates an overshoot recovery circuitry that turns on a
current sink to discharge the output capacitor in the event
OUTS is higher than SET. This current is typically about
4mA. No load recovery is disabled for input voltages less
than 2.5V or output voltages less than 1.5V.
30451fa
For more information www.linear.com/LT3045-1
21
LT3045-1
APPLICATIONS INFORMATION
VIN
5V ±5%
If OUTS is externally held above SET, the current sink
turns ON in an attempt to restore OUTS to its programmed
voltage. The current sink remains ON until the external
circuitry releases OUTS.
LT3045-1
IN
100µA
10µF
–
+
EN/UV
OUT
PGFB
VIOC
20mΩ
OUTS
SET
GND ILIM
PG
VOUT
3.3V
IOUT(MAX)
1A
LT3045-1
IN
100µA
–
+
EN/UV
OUT
PGFB
VIOC
20mΩ
OUTS
SET
GND ILIM
PG
10µF
30451 F07
16.5k
Direct Paralleling for Higher Current
10µF
0.47µF
Higher output current is obtained by paralleling multiple
LT3045-1s. Tie all SET pins together and all IN pins together.
Connect the OUT pins together using small pieces of PCB
trace (used as a ballast resistor) to equalize currents in
the LT3045-1s. PCB trace resistance in milliohms/inch is
shown in Table 2.
Table 2. PC Board Trace Resistance
WEIGHT (oz)
10mil WIDTH
20mil WIDTH
1
54.3
27.1
2
27.1
13.6
Trace resistance is measured in mΩ/in.
The small worst-case offset of 2mV for each paralleled
LT3045-1 minimizes the required ballast resistor value.
Figure 7 illustrates that two LT3045-1s, each using a 20mΩ
PCB trace ballast resistor, provide better than 20% accurate
output current sharing at full load. The two 20mΩ external
resistors only add 10mV of output regulation drop with a
1A maximum current. With a 3.3V output, this only adds
0.3% to the regulation accuracy. As has been discussed
previously, tie the OUTS pin directly to the output capacitor.
Figure 7. Parallel Devices
More than two LT3045-1s can also be paralleled for even
higher output current and lower output noise. Paralleling
multiple LT3045-1s is also useful for distributing heat on
the PCB. For applications with high input-to-output voltage
differential, an input series resistor or resistor in parallel
with the LT3045-1 can also be used to spread heat.
PCB Layout Considerations
Figure 8. Recommended DFN Layout
22
Given the LT3045-1’s high bandwidth and ultrahigh
PSRR, careful PCB layout must be employed to achieve
full device performance. Figure 8 shows a recommended
layout that delivers full performance of the regulator.
Refer to the LT3045-1’s DC2593A demo board manual
for further details.
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
APPLICATIONS INFORMATION
High Efficiency Linear Regulator: Voltage Input-toOutput Control (VIOC)
The VIOC pin is used to control an upstream switching
converter (e.g. buck, boost, buck-boost, etc) to maintain
a constant voltage across the LT3045-1, regardless of
the LDO’s output voltage. This maximizes efficiency
while maintaining PSRR performance. The VIOC pin is
the output of a fast unity-gain amplifier that measures
the difference between IN and OUT or 1.5V, whichever is
higher. As shown in Figure 9, the VIOC feature is simple
to use. Just tie the VIOC pin to the upstream switching
converter’s feedback (FB) pin, and this will regulate the
LT3045-1’s input-to-output differential to the switching
converter’s feedback voltage. When paralleling multiple
LT3045-1s, tie the VIOC pin of one of the LT3045-1 to the
upstream switching converter’s feedback pin and float the
remaining VIOC pins.
VIN
IN
VLDOIN
SW
FB
For example, for a switching converter with less than
100kHz bandwidth and a phase margin of 50°, using the
VIOC buffer, the phase margin will degrade by at most 2°.
Hence, the phase margin for the switching converter (using
the VIOC pin) will be at least 48°. Given the VIOC buffer is
inside the switching converter’s feedback loop, the total
capacitance on the VIOC pin is required to be below 20pF.
As shown in Figure 10, the input-to-output differential
voltage is easily programmable to support different apLT3045-1
IN
EN/UV
UPSTREAM
DC/DC
CONVERTER
While the VIOC buffer is inside the switching converter’s
feedback loop, given the VIOC buffer’s high bandwidth,
the switching converter’s frequency compensation doesn’t
need to be adjusted. Phase delay through the VIOC buffer
is typically less than 2° for frequencies as high as 100kHz;
hence, within the switching converter’s bandwidth (usually
much less than 100kHz), the VIOC buffer will be transparent and just act like an ideal wire.
+ –
OUT
VLDOOUT: VARIABLE
IOUT(MAX): 500mA
OUTS
10µF
1×
PGFB
VFBSWITCHER
VIOC
SET
R1
ILIM
GND
PG
30451 F09
0.47µF
Figure 9. VIOC Basic Operation
VIN
IN
EN/UV
UPSTREAM
DC/DC
CONVERTER
FB
LT3045-1
IN
SW
R3
R2
+ –
OUT
VOUT: VARIABLE
IOUT(MAX): 500mA
OUTS
10µF
1×
PGFB
VIOC
SET
R1
GND
ILIM
PG
30451 F10
0.47µF
Figure 10. Programming Input-to-Output Differential
30451fa
For more information www.linear.com/LT3045-1
23
LT3045-1
APPLICATIONS INFORMATION
plication needs (PSRR vs. power dissipation) using the
following equation:
VLDOIN – VLDOOUT = VVIOC = VFBSWITCHER •
be programmed below the upstream switching converter’s
feedback pin. For VOUT ≤ 1.5V, the VIOC programming
range is 1V ±5%. If VIOC is set to be outside this range,
then the LT3045-1 input voltage will rise to the maximum
value set using R3. If VIOC functionality is not used, float
the VIOC pin.
R1+R2
R1
Furthermore, in the event the LT3045-1 SET pin opens up,
the LT3045-1 input voltage can rise up to the switcher’s
input voltage, and thus potentially violate the LT3045-1’s
absolute maximum rating. To prevent this, the maximum
LT3045-1 input voltage can be set using a resistor (R3)
between the VIOC and IN pins of the regulator such that:
V(MAX)LDOIN = VFBSWITCHER •
Given the maximum VIOC programming voltage is dependent on VOUT, care must be taken in setting the VIOC
voltage. For instance, if VIOC is set to 1V, the LDO’s INto-OUT differential will be regulated to 1V for VOUT > 1.5V.
Similarly, if VIOC is set to 2V, the regulator’s IN-to-OUT
differential will be regulated to 2V for VOUT > 2.5V (i.e.
VVIOC + 0.5V). However, if the output voltage is below
2.5V, for this example, then the LDO will not be able to
drive its VIOC pin to the right level of 2V. As a result, the
upstream pre-regulator’s output will rise, thereby causing the LT3045-1 input voltage to rise to the maximum
voltage set using R3. Hence, for protection under various
fault conditions, the use of R3 to set the maximum VIN
voltage (below 20V) is required.
R1+R2+R3
+ISINK • R3
R1
Moreover, the VIOC pin is capable of sourcing 200µA
and sinking 15µA of current. To mitigate the effect of the
sink current on the maximum LDO input voltage (shown
above), choose R1 such that the resistor divider typically
runs at least 100µA.
For VOUT > 1.5V, VIN = VOUT + VVIOC. The VIOC pin voltage (and hence the input-to-output differential) can be
programmed anywhere between a minimum of 1V and
a maximum of 4V or VOUT – 0.5V (for VOUT > 1.5V),
whichever is lower. For applications where the feedback
pin of the switching regulator is below 1V, use resistors
R1 and R2 to make sure the VIOC pin is within the aforementioned range. Note that the VIOC pin voltage cannot
VIN
20V
IN
10nF
40.2k
LT8608
BST
EN/UV
SW
TR/SS
PG
0.22µF
2.2µH
LT3045-1
EN/UV
100µA
–
+
PGFB
2.21k
FB
INTVCC GND
Figure 11 shows a typical VIOC application used to postregulate the output of the LT8608 buck converter. The VIOC
voltage is set at 1V with the maximum LDO input voltage
set to 16.5V. Figure 12 shows the LDO’s input and output
voltage when pulsing the LT3045-1’s EN/UV pin, and as
IN
47µF
MODE
RT
Typical VIOC Application
7.68k
140k
VLDOIN – VLDOUT = 1V
VMAXLDOIN = 16.5V
OUT
OUTS
VIOC
SET
GND ILIM
PG
10µF
30451 F11
1µF
fSW = 1MHz
L: XFL4020-222MEC
VOUT: VARIABLE
IOUT(MAX): 500mA
4.7µF
249Ω
Figure 11. Typical LT3045-1 Post-Regulating Application
24
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
APPLICATIONS INFORMATION
can be seen, when the LDO is disabled, the LDO input voltage goes to the maximum input voltage set by the resistor
divider on the VIOC pin. Figure 13 shows the load step
response of the LT8608 using the VIOC buffer. Figure 14
shows the LDO’s input and output voltage response to
stepping the set pin from 3V to 4V. Figure 15 shows the
LDO’s output and input voltage while ramping the SET
pin from 0V to 10V, and as can be seen, the LT8608’s
output voltage tracks the LT3045’s output voltage when
it is greater than 1.5V. Lastly, Figure 16 shows the noise
spectral density at the LT3045-1 input and output.
1V/DIV
VSET AND LDOOUT ARE OVERLAID
0V
VSET
LDOIN
LDOOUT
1ms/DIV
30451 F14
VSET = 3V TO 4V
IL = 500mA
Figure 14. Stepping VSET from 3V to 4V (and Back to 3V)
VSET
LDOOUT
LDOIN
5V/DIV
0V
2V/DIV
VEN/UV
LDOIN
LDOOUT
0V
1V/DIV
VSET AND LDOOUT ARE OVERLAID
0V
500ms/DIV
30451 F12
RSET = 33.2kΩ
RL = 6.6Ω
VIN LT8608 = 20V
Figure 15. Ramping VSET from 0V to 10V (and Back to 0V)
Figure 12. LT3045-1 EN/UV Pulse
1000
LDOIN = 4.3V
LDOOUT = 3.3V
100 ILOAD = 500mA
NOISE (µV/√Hz)
0mA
500mA/DIV
100mV/DIV
50mV/DIV
ILOAD
LDOIN (ac)
LDOOUT (ac)
200µs/DIV
RSET = 33.2kΩ
ILOAD = 10mA to 500mA
30451 F15
5ms/DIV
IL = 500mA
30451 F13
10
1
0.1
0.01
LDOOUT
LDOIN
Noise Floor
10
100
1k
10k 100k
FREQUENCY (Hz)
1M
10M
30451 F16
Figure 13. Load Step Response Using the VIOC Buffer
Figure 16. LT3045-1’s Input and Output Noise Spectral Density
30451fa
For more information www.linear.com/LT3045-1
25
LT3045-1
APPLICATIONS INFORMATION
Thermal Considerations
Table 3. Measured Thermal Resistance for DFN Package
The LT3045-1 has internal power and thermal limiting
circuits that protect the device under overload conditions.
The thermal shutdown temperature is nominally 165°C
with about 8°C of hysteresis. For continuous normal
load conditions, do not exceed the maximum junction
temperature (125°C for E- and I-grades). It is important to
consider all sources of thermal resistance from junction to
ambient. This includes junction-to-case, case-to-heat sink
interface, heat sink resistance or circuit board-to-ambient
as the application dictates. Additionally, consider all heat
sources in close proximity to the LT3045-1.
The undersides of the DFN and MSOP packages have
exposed metal from the lead frame to the die attachment.
Both packages allow heat to directly transfer from the die
junction to the PCB metal to limit maximum operating
junction temperature. The dual-in-line pin arrangement
allows metal to extend beyond the ends of the package
on the topside (component side) of the PCB.
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PCB and its
copper traces. Copper board stiffeners and plated throughholes can also be used to spread the heat generated by
the regulator.
Tables 3 and 4 list thermal resistance as a function of copper
area on a fixed board size. All measurements were taken
in still air on a 4 layer FR-4 board with 1oz solid internal
planes and 2oz top/bottom planes with a total board thickness of 1.6mm. The four layers were electrically isolated
with no thermal vias present. PCB layers, copper weight,
board layout and thermal vias affect the resultant thermal
resistance. For more information on thermal resistance
and high thermal conductivity test boards, refer to JEDEC
standard JESD51, notably JESD51-7 and JESD51-12.
Achieving low thermal resistance necessitates attention
to detail and careful PCB layout.
COPPER AREA
TOP SIDE*
BOTTOM SIDE
BOARD AREA
THERMAL
RESISTANCE
2500mm2
2500mm2
2500mm2
34°C/W
1000mm2
2500mm2
2500mm2
34°C/W
225mm2
2500mm2
2500mm2
35°C/W
100mm2
2500mm2
2500mm2
36°C/W
*Device is mounted on topside
Table 4. Measured Thermal Resistance for MSOP Package
COPPER AREA
TOP SIDE*
BOTTOM SIDE
BOARD AREA
THERMAL
RESISTANCE
2500mm2
2500mm2
2500mm2
33°C/W
1000mm2
2500mm2
2500mm2
33°C/W
225mm2
2500mm2
2500mm2
34°C/W
100mm2
2500mm2
2500mm2
35°C/W
*Device is mounted on topside
Calculating Junction Temperature
Example: Given an output voltage of 3.3V and input voltage
of 5V ± 5%, output current range from 1mA to 500mA,
and a maximum ambient temperature of 85°C, what is the
maximum junction temperature?
The LT3045-1’s power dissipation is:
IOUT(MAX) • (VIN(MAX) – VOUT) + IGND • VIN(MAX)
where:
IOUT(MAX) = 500mA
VIN(MAX) = 5.25V
IGND (at IOUT = 500mA and VIN = 5.25V) = 12.5mA
thus:
PDISS = 0.5A • (5.25V – 3.3V) + 12.5mA • 5.25V = 1W
Using a DFN package, the thermal resistance is in the
range of 34°C/W to 36°C/W depending on the copper area.
Therefore, the junction temperature rise above ambient
approximately equals:
1W • 35°C/W = 35°C
26
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
APPLICATIONS INFORMATION
The maximum junction temperature equals the maximum ambient temperature plus the maximum junction
temperature rise above ambient:
TJMAX = 85°C + 35°C = 120°C
Overload Recovery
Like many IC power regulators, the LT3045-1 incorporates
safe-operating-area (SOA) protection. The SOA protection
activates at input-to-output differential voltages greater
than 12V. The SOA protection decreases the current limit
as the input-to-output differential increases and keeps
the power transistor inside a safe operating region for all
values of input-to-output voltages up to the LT3045-1’s
absolute maximum ratings. The LT3045-1 provides some
level of output current for all values of input-to-output differentials. Refer to the Current Limit curves in the Typical
Performance Characteristics section. When power is first
applied and input voltage rises, the output follows the input
and keeps the input-to-output differential low to allow the
regulator to supply large output current and start-up into
high current loads.
Due to current limit foldback, however, at high input voltages a problem can occur if the output voltage is low and
the load current is high. Such situations occur after the
removal of a short-circuit or if the EN/UV pin is pulled high
after the input voltage has already turned ON. The load
line in such cases intersects the output current profile at
two points. The regulator now has two stable operating
points. With this double intersection, the input power
supply may need to be cycled down to zero and brought
back up again to make the output recover. Other linear
regulators with foldback current limit protection (such as
the LT1965 and LT1963A) also exhibit this phenomenon,
so it is not unique to the LT3045-1.
Protection Features
The LT3045-1 incorporates several protection features for
battery-powered applications. Precision current limit and
thermal overload protection protect the LT3045-1 against
overload and fault conditions at the device’s output. For
normal operation, do not allow the junction temperature
to exceed 125°C (E-grade, I-grade).
To protect the LT3045-1’s low noise error amplifier, the
SET-to-OUTS protection clamp limits the maximum voltage
between SET and OUTS with a maximum DC current of
20mA through the clamp. So for applications where SET
is actively driven by a voltage source, the voltage source
must be current limited to 20mA or less. Moreover, to limit
the transient current flowing through these clamps during
a transient fault condition, limit the maximum value of the
SET pin capacitor (CSET) to 22µF.
The LT3045-1 also incorporates reverse input protection
whereby the IN pin withstands reverse voltages of up to
–20V without causing any input current flow and without
developing negative voltages at the OUT pin. The regulator
protects both itself and the load against batteries that are
plugged-in backwards.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled to
GND, pulled to some intermediate voltage, or left opencircuit. In all of these cases, the reverse-current protection
circuitry prevents current flow from output to the input.
Nonetheless, due to the OUTS-to-SET clamp, unless the
SET pin is floating, current can flow to GND through the
SET pin resistor as well as up to 15mA to GND through
the output overshoot recovery circuitry. This current flow
through the output overshoot recovery circuitry can be
significantly reduced by placing a Schottky diode between
OUTS and SET pins, with its anode at the OUTS pin.
30451fa
For more information www.linear.com/LT3045-1
27
LT3045-1
TYPICAL APPLICATIONS
12VIN to 3.3VOUT with 0.8µVRMS Integrated Noise
LT3045-1
IN
VIN
12V ±5%
4.7µF
100µA
–
+
EN/UV
200k
PG
VIOC
VOUT
3.3V
IOUT
200mA
OUT
OUTS
SET
GND
ILIM
10µF
PGFB
453k
4.7µF
750Ω
33.2k
49.9k
30451 TA02
Low Noise CC/CV Lab Power Supply
LT3045-1
IN
VIN
4.7µF
Ultralow Noise Current Source for RF Biasing Applications
VIN
1.8V TO 20V
4.7µF
100µA
–
+
EN/UV
PGFB
–
+
PGFB
OUT
VOUT
OUTS
SET
100µA
EN/UV
PG
VIOC
LT3045-1
IN
GND
ILIM
10µF
ROUT = R1 + RLOAD
OUT
PG
VIOC
R1
1Ω
VOUT(MAX): 15V
OUTS
SET
GND
ILIM
10µF
RLOAD
0.47µF
RSET
4.7µF
RIOUT
RSET
2k
30451 TA03
30451 TA04
VOUT(MAX) = 100μA • RSET
IOUT(MAX) =
28
150mA • kΩ
RIOUT
OUTPUT CURRENT NOISE = 0.8µVRMS/ROUT
INCREASE R1 (AND RSET) TO REDUCE CURRENT NOISE
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
TYPICAL APPLICATIONS
Programming Undervoltage Lockout
VIN
4V Turn-ON
3.4V Turn-OFF
4.7µF
LT3045-1
IN
100µA
PGFB
REN2
110k
PG
⎛ 110k ⎞
VIN(UVLO)RISING =1.24V • ⎜1+
⎟
⎝ 49.9k ⎠
–
+
REN1
49.9k
VIOC
VOUT
3.3V
IOUT(MAX)
500mA
OUT
EN/UV
OUTS
SET
10µF
GND ILIM
30451 TA05
0.47µF
33.2k
Ratiometric Tracking
LT3045-1
IN
100µA
–
+
EN/UV
PGFB
IN
VIN
5.5V TO 20V
–
+
EN/UV
PGFB
0.1µF
OUT
PG
VIOC
0.1µF
OUTS
SET
GND
ILIM
10µF
VOUT
5V
OUTS
VIOC
100µA
10µF
OUT
PG
LT3045-1
SET
16.9k
GND
10µF
ILIM
30451 TA06
VOUT
3.3V
MIN LOAD 200µA
33.2k
30451fa
For more information www.linear.com/LT3045-1
29
LT3045-1
TYPICAL APPLICATIONS
Ultralow 1/f Noise Reference Buffer
VIN
6V ±5%
LT3045-1
IN
100µA
4.7µF
–
+
EN/UV
PGFB
1,2
6,7
LTC6655-5
VIOC
3,4,5
VOUT = 5V
IOUT(MAX)
500mA
OUT
PG
OUTS
SET
GND
10µF
ILIM
1k
30451 TA07
10µF
49.9k
4.7µF
Paralleling Multiple Devices Using ILIM (Current Monitor) to Cancel Ballast Resistor Drop
LT3045-1
IN
10µF
LT3045-1
100µA
EN/UV
VOUT = 3.3V
IOUT(MAX) = 1A
PGFB
OUT
PG
VIOC
OUTS
SET
IN
100µA
–
+
GND
ILIM
+
–
VIN
5V ±5%
OUT
20mΩ
10µF
20mΩ
EN/UV
PGFB
PG
OUTS
ILIM
10µF
RILIM
287Ω
GND
SET VIOC
287Ω
30451 TA08
1µF
16.5k
N = NUMBER OF DEVICES IN PARALLEL
RCDC = CABLE (BALLAST RESISTOR) DROP CANCELLATION RESISTOR
RILIM = CURRENT LIMIT PROGRAMMING RESISTOR
RBALLAST = BALLAST RESISTOR
ILIM = OUTPUT CURRENT LIMIT
30
RCDC
5Ω
RILIM = 150mA • kΩ/ILIM – RCDC • N
= 287Ω (FOR 500mA ILIM PER REGULATOR)
RCDC = RBALLAST • 500/N
= 5Ω
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
TYPICAL APPLICATIONS
Paralleling Multiple LT3045-1s for 2A Output Current
LT3045-1
IN
VIN
5V ±5%
22µF
LT3045-1
100µA
100µA
–
+
200k
OUT
PG
OUT
20mΩ
OUTS
SET ILIM
GND
+
–
EN/UV
PGFB
20mΩ
10µF
ILIM
10µF
EN/UV
PGFB
PG
OUTS
GND
SET VIOC
453k
49.9k
VOUT = 3.3V
IOUT(MAX) = 2A
DROPOUT = 300mV
0.8µVRMS
4
= 0.4µVRMS
OUTPUT NOISE =
LT3045-1
IN
LT3045-1
100µA
EN/UV
PGFB
OUT
PG
VIOC
OUT
20mΩ
OUTS
SET
IN
100µA
–
+
GND
+
–
VIOC
IN
ILIM
10µF
4.7µF
20mΩ
10µF
PGFB
PG
OUTS
ILIM
EN/UV
GND
SET VIOC
8.25k
30451 TA09
30451fa
For more information www.linear.com/LT3045-1
31
LT3045-1
TYPICAL APPLICATIONS
Low Noise Wheatstone Bridge Power Supply
LT1763 NOISE: 20µVRMS (10Hz TO 100kHz)
LT3045-1 NOISE: 0.8µVRMS (10Hz TO 100kHz)
LT3045-1
IN
VIN
5V ±5%
4.7µF
100µA
EN/UV
200k
–
+
OUT
PG
RESISTOR
TOLERANCE
BRIDGE PSRR
NOISE AT VBRIDGE
USING LT1763
NOISE AT VBRIDGE
USING LT3045-1
PERFECT
MATCHING
INFINITE
–
–
1%
40dB
200nVRMS
8nVRMS
5%
26dB
1000nVRMS
42.5nVRMS
VOUT: 3.3V AND IOUT(MAX): 500mA
R1
OUTS
VIOC
SET
GND ILIM PGFB
10µF
R3
VBRIDGE
453k
+
R2
4.7µF
–
R4
49.9k
33.2k
30451 TA10
PGFB Disabled without Reverse Input Protection
LT3045-1
IN
VIN
4.7µF
PGFB Disabled with Reverse Input Protection
4.7µF
100µA
–
+
EN/UV
PGFB
0.47µF
VIOC
OUT
VOUT
PGFB
OUTS
GND
ILIM
PG
10µF
RSET
0.47µF
30451 TA11
32
–
+
1N4148
OUT
SET
100µA
EN/UV
PG
VIOC
LT3045-1
IN
VIN
VOUT
OUTS
SET
GND
ILIM
10µF
RSET
30451 TA12
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LT3045-1#packaging for the most recent package drawings.
DD Package
12-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1725 Rev A)
0.70 ±0.05
3.50 ±0.05
2.10 ±0.05
2.38 ±0.05
1.65 ±0.05
PACKAGE
OUTLINE
0.25 ±0.05
0.45 BSC
2.25 REF
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
3.00 ±0.10
(4 SIDES)
R = 0.115
TYP
7
0.40 ±0.10
12
2.38 ±0.10
1.65 ±0.10
PIN 1 NOTCH
R = 0.20 OR
0.25 × 45°
CHAMFER
PIN 1
TOP MARK
(SEE NOTE 6)
6
0.200 REF
1
0.23 ±0.05
0.45 BSC
0.75 ±0.05
2.25 REF
0.00 – 0.05
(DD12) DFN 0106 REV A
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD AND TIE BARS SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
30451fa
For more information www.linear.com/LT3045-1
33
LT3045-1
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LT3045-1#packaging for the most recent package drawings.
MSE Package
12-Lead Plastic MSOP, Exposed Die Pad
(Reference LTC DWG # 05-08-1666 Rev G)
BOTTOM VIEW OF
EXPOSED PAD OPTION
2.845 ±0.102
(.112 ±.004)
5.10
(.201)
MIN
2.845 ±0.102
(.112 ±.004)
0.889 ±0.127
(.035 ±.005)
6
1
1.651 ±0.102
(.065 ±.004)
1.651 ±0.102 3.20 – 3.45
(.065 ±.004) (.126 – .136)
12
0.65
0.42 ±0.038
(.0256)
(.0165 ±.0015)
BSC
TYP
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
0.35
REF
4.039 ±0.102
(.159 ±.004)
(NOTE 3)
0.12 REF
DETAIL “B”
CORNER TAIL IS PART OF
DETAIL “B” THE LEADFRAME FEATURE.
FOR REFERENCE ONLY
7
NO MEASUREMENT PURPOSE
0.406 ±0.076
(.016 ±.003)
REF
12 11 10 9 8 7
DETAIL “A”
0° – 6° TYP
3.00 ±0.102
(.118 ±.004)
(NOTE 4)
4.90 ±0.152
(.193 ±.006)
GAUGE PLANE
0.53 ±0.152
(.021 ±.006)
DETAIL “A”
1.10
(.043)
MAX
0.18
(.007)
SEATING
PLANE
0.22 – 0.38
(.009 – .015)
TYP
1 2 3 4 5 6
0.650
(.0256)
BSC
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
6. EXPOSED PAD DIMENSION DOES INCLUDE MOLD FLASH. MOLD FLASH ON E-PAD SHALL
NOT EXCEED 0.254mm (.010") PER SIDE.
34
0.86
(.034)
REF
0.1016 ±0.0508
(.004 ±.002)
MSOP (MSE12) 0213 REV G
30451fa
For more information www.linear.com/LT3045-1
LT3045-1
REVISION HISTORY
REV
DATE
DESCRIPTION
A
09/17
Modified Typical Application circuit.
PAGE NUMBER
1
Modified conditions for 3 VIOC curves: IOUT = 1mA.
12
Modified Figure 11.
23
30451fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more
information
www.linear.com/LT3045-1
tion that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
35
LT3045-1
TYPICAL APPLICATION
Parallel Devices
VIN
IN
UPSTREAM
DC/DC CONVERTER
FB
LT3045-1
IN
SW
R3
R2
R1
100µA
–
+
EN/UV
OUT
PGFB
20mΩ
OUTS
VIOC
SET
GND ILIM
PG
10µF
VOUT: VARIABLE
IOUT(MAX): 1A
LT3045-1
IN
100µA
–
+
EN/UV
OUT
PGFB
VIOC
20mΩ
OUTS
SET
GND ILIM
PG
10µF
30451 TA13
0.47µF
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1761
100mA, Low Noise LDO
300mV Dropout Voltage, Low Noise: 20µVRMS, VIN = 1.8V to 20V,
TSOT-23 Package
LT1763
500mA, Low Noise LDO
300mV Dropout Voltage, Low Noise: 20μVRMS, VIN = 1.8V to 20V,
4mm × 3mm DFN and SO-8 Packages
LT3042
200mA, Ultralow Noise and Ultrahigh PSRR LDO
0.8μVRMS Noise and 79dB PSRR at 1MHz, VIN = 1.8V to 20V, 350mV
Dropout Voltage, Programmable Current Limit and Power Good,
3mm × 3mm DFN and MSOP Packages
LT3045
500mA, Ultralow Noise and Ultrahigh PSRR LDO
0.8μVRMS Noise and 76dB PSRR at 1MHz, VIN = 1.8V to 20V, 260mV
Dropout Voltage, Programmable Current Limit and Power Good,
3mm × 3mm DFN and MSOP Packages
LT3065
500mA Low Noise LDO with Soft-Start
300mV Dropout Voltage, Low Noise: 25μVRMS, VIN = 1.8V to 45V,
3mm × 3mm DFN and MSOP Packages
LT3080
1.1A, Parallelable, Low Noise, Low Dropout Linear Regulator
300mV Dropout Voltage (2-Supply Operation), Low Noise: 40μVRMS,
VIN: 1.2V to 36V, VOUT: 0V to 35.7V, Current-Based Reference with
1-Resistor VOUT Set; Directly Parallelable (No Op Amp Required),
Stable with Ceramic Capacitors; TO-220, DD-Pak, SOT-223, MSOP
and 3mm × 3mm DFN-8 Packages; LT3080-1 Version Has Integrated
Internal Ballast Resistor
LT3085
500mA, Parallelable, Low Noise, Low Dropout Linear
Regulator
275mV Dropout (2-Supply Operation), Low Noise: 40μVRMS, VIN: 1.2V
to 36V, VOUT: 0V to 35.7V, Current-Based Reference with 1-Resistor
VOUT Set, Directly Parallelable (No Op Amp Required), Stable with
Ceramic Capacitors; MS8E and 2mm × 3mm DFN-6 Packages
36
30451fa
LT 0917 REV A • PRINTED IN USA
For more information www.linear.com/LT3045-1
www.linear.com/LT3045-1
LINEAR TECHNOLOGY CORPORATION 2017