LT8390A
60V 2MHz Synchronous
4-Switch Buck-Boost Controller
with Spread Spectrum
FEATURES
DESCRIPTION
4-Switch Single Inductor Architecture Allows VIN
Above, Below or Equal to VOUT
n Up to 95% Efficiency at 2MHz
n Proprietary Peak-Buck Peak-Boost Current Mode
n Wide V Range: 4V to 60V
IN
n ±1.5% Output Voltage Accuracy: 1V ≤ V
OUT ≤ 60V
n ±3% Input or Output Current Accuracy with Monitor
n Spread Spectrum Frequency Modulation for Low EMI
n High Side PMOS Load Switch Driver
n No Top MOSFET Refresh Noise in Buck or Boost
n Adjustable and Synchronizable: 600kHz to 2MHz
n V
OUT Disconnected from VIN During Shutdown
n Available in 28-Lead TSSOP with Exposed Pad and
28-Lead QFN (4mm × 5mm)
n AEC-Q100 Qualified for Automotive Applications
The LT®8390A is a synchronous 4-switch buck-boost DC/DC
controller that regulates output voltage, input or output
current from an input voltage above, below, or equal to
the output voltage. The proprietary peak-buck peak-boost
current mode control scheme allows adjustable and synchronizable 600kHz to 2MHz fixed frequency operation, or
internal 25% triangle spread spectrum frequency modulation for low EMI. With a 4V to 60V input voltage range,
0V to 60V output voltage capability, and seamless low
noise transitions between operation regions, the LT8390A
is ideal for voltage regulator, battery and supercapacitor
charger applications in automotive, industrial, telecom,
and even battery-powered systems.
n
APPLICATIONS
n
n
Automotive, Industrial, Telecom Systems
High Frequency Battery-Powered System
The LT8390A provides input or output current monitor
and power good flag. Fault protection is also provided to
detect output short-circuit condition, during which the
LT8390A retries, latches off, or keeps running.
All registered trademarks and trademarks are the property of their respective owners.
TYPICAL APPLICATION
95% Efficient 48W (12V 4A) 2MHz Buck-Boost Voltage Regulator
VIN
6V TO 28V
CONTINUOUS
4V TO 56V
TRANSIENT
1µH
5mΩ
22µF
63V
0.1µF
100V
×2
0.1µF
4.7µF
100V
×2
SW1 LSP
BST1
INTVCC
LSN
10mΩ
0.1µF
SW2
BST2
BG1
BG2
0.1µF
16V
×2
VOUT
12V
4A
22µF
16V
×2
22µF
16V
Efficiency vs VIN
100
INTVCC
GND
VIN
383k
VOUT
1µF
169k
1µF
EN/UVLO
ISP
LOADTG
ISN
TEST
ISMON
ISMON
133k
0.47µF
10Ω
1µF 10Ω
FB
SSFM OFF
SYNC/SPRD
CTRL
100k
90
TG2
LT8390A
INTVCC
INTVCC
4.7µF
LOADEN
VREF
SS
22nF
PGOOD
RT
VC
SSFM ON
100k
PGOOD
110k
10k
EFFICIENCY (%)
TG1
80
70
IOUT = 4A
IOUT = 2A
60
50
CONTINUOUS OPERATION WITH
HIGHEST COMPONENT TEMPERATURE
BELOW 90°C (TA = 25°C)
0
5
10
15 20 25 30
INPUT VOLTAGE (V)
35
40
8390a TA01b
59.0k
2MHz
10k
2.2nF
8390a TA01a
Rev. B
Document Feedback
For more information www.analog.com
1
LT8390A
ABSOLUTE MAXIMUM RATINGS
(Note 1)
VIN, EN/UVLO, VOUT, ISP, ISN....................................60V
(ISP-ISN)..........................................................–1V to 1V
BST1, BST2................................................................66V
SW1, SW2, LSP, LSN..................................... –6V to 60V
INTVCC, (BST1-SW1), (BST2-SW2)..............................6V
(BST1-LSP), (BST1-LSN).............................................6V
FB, LOADEN, SYNC/SPRD, CTRL, PGOOD...................6V
Operating Junction Temperature Range (Notes 2, 3)
LT8390AE........................................... –40°C to 125°C
LT8390AI............................................ –40°C to 125°C
LT8390AH........................................... –40°C to 150°C
LT8390AJ........................................... –40°C to 150°C
Storage Temperature Range................... –65°C to 150°C
PIN CONFIGURATION
TOP VIEW
TOP VIEW
SW1
3
26 SW2
TG1
4
25 TG2
TG1 1
22 TG2
LSP
5
24 VOUT
LSP 2
21 VOUT
LSN
6
23 LOADTG
LSN 3
20 LOADTG
22 SYNC/SPRD
21 RT
INTVCC 5
9
20 VC
EN/UVLO 6
TEST 10
19 FB
LOADEN 11
18 SS
CTRL 13
16 ISMON
ISP 14
16 FB
15 SS
9 10 11 12 13 14
15 ISN
FE PACKAGE
28-LEAD PLASTIC TSSOP
θJA = 30°C/W, θJC = 5°C/W
EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB
PGOOD
17 PGOOD
TEST 7
LOADEN 8
ISMON
VREF 12
18 RT
17 VC
ISN
EN/UVLO
8
19 SYNC/SPRD
29
GND
VREF
INTVCC
2
VIN 4
ISP
7
28 27 26 25 24 23
CTRL
VIN
29
GND
SW2
27 BST2
BST2
2
BG2
BST1
BG1
28 BG2
BST1
1
SW1
BG1
UFD PACKAGE
28-LEAD (4mm × 5mm) PLASTIC QFN
θJA = 43°C/W, θJC = 3.4°C/W
EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB
Rev. B
For more information www.analog.com
LT8390A
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT8390AEFE#PBF
LT8390AEFE#TRPBF
LT8390AFE
28-Lead Plastic TSSOP
–40°C to 125°C
LT8390AIFE#PBF
LT8390AIFE#TRPBF
LT8390AFE
28-Lead Plastic TSSOP
–40°C to 125°C
LT8390AHFE#PBF
LT8390AHFE#TRPBF
LT8390AFE
28-Lead Plastic TSSOP
–40°C to 150°C
LT8390AJFE#PBF
LT8390AJFE#TRPBF
LT8390AFE
28-Lead Plastic TSSOP
–40°C to 150°C
LT8390AEUFD#PBF
LT8390AEUFD#TRPBF
8390A
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT8390AIUFD#PBF
LT8390AIUFD#TRPBF
8390A
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT8390AJUFD#PBF
LT8390AJUFD#TRPBF
8390A
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 150°C
LT8390AHUFD#PBF
LT8390AHUFD#TRPBF
8390A
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 150°C
LT8390AJFE#WPBF
LT8390AJFE#WTRPBF
LT8390AFE
28-Lead Plastic TSSOP
–40°C to 150°C
LT8390AHFE#WPBF
LT8390AHFE#WTRPBF
LT8390AFE
28-Lead Plastic TSSOP
–40°C to 150°C
LT8390AJUFD#WPBF
LT8390AJUFD#WTRPBF
8390A
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 150°C
LT8390AHUFD#PBF
LT8390AHUFD#WTRPBF
8390A
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 150°C
AUTOMOTIVE PRODUCTS**
Contact the factory for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Tape and reel specifications. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix.
**Versions of this part are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. These
models are designated with a #W suffix. Only the automotive grade products shown are available for use in automotive applications. Contact your
local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for
these models.
Rev. B
For more information www.analog.com
3
LT8390A
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 12V, VEN/UVLO = 1.5V unless otherwise noted.
PARAMETER
Supply
VIN Operating Voltage Range
VIN Quiescent Current
VOUT Voltage Range
VOUT Quiescent Current
Linear Regulators
INTVCC Regulation Voltage
INTVCC Load Regulation
INTVCC Line Regulation
INTVCC Current Limit
INTVCC Dropout Voltage (VIN – INTVCC)
INTVCC Undervoltage Lockout Threshold
INTVCC Undervoltage Lockout Hysteresis
VREF Regulation Voltage
VREF Load Regulation
VREF Line Regulation
VREF Current Limit
VREF Undervoltage Lockout Threshold
VREF Undervoltage Lockout Hysteresis
Control Inputs/Outputs
EN/UVLO Shutdown Threshold
EN/UVLO Enable Threshold
EN/UVLO Enable Hysteresis
EN/UVLO Hysteresis Current
CTRL Input Bias Current
CTRL Latch-Off Threshold
CTRL Latch-Off Hysteresis
Load Switch Driver
LOADEN Threshold
LOADEN Hysteresis
Minimum VOUT for LOADTG to be On
LOADTG On Voltage V(VOUT-LOADTG)
LOADTG Off Voltage V(VOUT-LOADTG)
LOADEN to LOADTG Turn On Propagation Delay
LOADEN to LOADTG Turn Off Propagation Delay
LOADTG Turn On Fall Time
LOADTG Turn Off Rise Time
4
CONDITIONS
MIN
l
4
VEN/UVLO = 0.3V
VEN/UVLO = 1.1V
Not Switching
1
270
2.1
l
VEN/UVLO = 0.3V, VOUT = 12V
VEN/UVLO = 1.1V, VOUT = 12V
Not Switching, VOUT = 12V
0
20
IINTVCC = 20mA
IINTVCC = 0mA to 80mA
IINTVCC = 20mA, VIN = 6V to 60V
VINTVCC = 4.5V
IINTVCC = 20mA, VIN = 4V
Falling
IVREF = 100µA
IVREF = 0mA to 1mA
IVREF = 100µA, VIN = 4V to 60V
VREF = 1.8V
Falling
4.85
110
3.44
l
1.97
2
1.78
l
0.3
1.196
VEN/UVLO = 0.3V
VEN/UVLO = 1.1V
VEN/UVLO = 1.3V
VCTRL = 0.75V, Current Out of Pin
Falling
l
–0.1
2.1
–0.1
0
285
Rising
l
1.3
l
Falling
VLOADEN = 5V
VOUT = 12V
VOUT = 12V
CLOADTG = 3.3nF to VOUT, 50% to 50%
CLOADTG = 3.3nF to VOUT, 50% to 50%
CLOADTG = 3.3nF to VOUT, 10% to 90%
CLOADTG = 3.3nF to VOUT, 90% to 10%
TYP
4.5
–0.1
0.1
0.1
40
5.0
1
1
145
160
3.54
0.24
2.00
0.4
0.1
2.5
1.84
50
MAX
60
2
2.8
60
0.5
0.5
60
5.15
4
4
190
3.64
2.03
1
0.2
3.2
1.90
0.6
1.220
13
0
2.5
0
20
300
25
1.0
1.244
1.4
220
2.4
5
0
90
40
300
10
1.5
0.1
2.9
0.1
50
315
3
5.5
0.1
UNITS
V
µA
µA
mA
V
µA
µA
µA
V
%
%
mA
mV
V
V
V
%
%
mA
V
mV
V
V
mV
µA
µA
µA
nA
mV
mV
V
mV
V
V
V
ns
ns
ns
ns
Rev. B
For more information www.analog.com
LT8390A
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 12V, VEN/UVLO = 1.5V unless otherwise noted.
PARAMETER
Error Amplifier
Full Scale Current Regulation V(ISP-ISN)
1/10th Current Regulation V(ISP-ISN)
ISMON Monitor Output VISMON
ISP/ISN Input Common Mode Range
ISP/ISN Low Side to High Side Switchover Voltage
ISP/ISN High Side to Low Side Switchover Voltage
ISP Input Bias Current
ISN Input Bias Current
ISP/ISN Current Regulation Amplifier gm
FB Regulation Voltage
FB Line Regulation
FB Load Regulation
FB Voltage Regulation Amplifier gm
FB Input Bias Current
VC Output Impedance
VC Standby Leakage Current
Current Comparator
Maximum Current Sense Threshold V(LSP-LSN)
LSP Pin Bias Current
LSN Pin Bias Current
Fault
FB Overvoltage Threshold (VFB)
FB Overvoltage Hysteresis
FB Short Threshold (VFB)
FB Short Hysteresis
ISP/ISN Over Current Threshold V(ISP-ISN)
PGOOD Upper Threshold Offset from VFB
PGOOD Lower Threshold Offset from VFB
PGOOD Pull-Down Resistance
SS Hard Pull-Down Resistance
SS Pull-Up Current
SS Pull-Down Current
SS Fault Latch-Off Threshold
SS Fault Reset Threshold
CONDITIONS
VCTRL = 2V, VISP = 12V
VCTRL = 2V, VISP = 0V
VCTRL = 0.35V, VISP = 12V
VCTRL = 0.35V, VISP = 0V
V(ISP-ISN) = 100mV, VISP = 12V/0V
V(ISP-ISN) = 10mV, VISP = 12V/0V
V(ISP-ISN) = 0mV, VISP = 12V/0V
l
l
l
l
l
l
l
l
MIN
TYP
MAX
UNITS
97
97
8
8
1.20
0.30
0.20
0
100
100
10
10
1.25
0.35
0.25
103
103
12
12
1.30
0.40
0.30
60
mV
mV
mV
mV
V
V
V
V
V
V
µA
µA
µA
µA
µA
µA
µs
V
%
%
µS
nA
MΩ
nA
VISP = VISN
VISP = VISN
VLOADEN = 5V, VISP = VISN = 12V
VLOADEN = 5V, VISP = VISN = 0V
VEN/UVLO = 0V, VISP = VISN = 12V or 0V
VLOADEN = 5V, VISP = VISN = 12V
VLOADEN = 5V, VISP = VISN = 0V
VEN/UVLO = 0V, VISP = VISN = 12V or 0V
VC = 1.2V
VIN = 4V to 60V
l
0.985
FB in Regulation, Current Out of Pin
VC = 1.2V, VLOADEN = 0V
–10
1.8
1.7
23
–10
0
23
–10
0
2000
1.00
0.2
0.2
660
10
10
0
1.015
0.5
0.8
40
10
Buck, VFB = 0.8V
Boost, VFB = 0.8V
VLSP = VLSN = 12V
VLSP = VLSN = 12V
l
l
35
40
50
50
60
60
65
60
mV
mV
µA
µA
Rising
l
1.08
35
0.24
35
1.1
50
0.25
50
750
10
–10
100
100
12.5
1.25
1.7
0.2
1.12
65
0.26
65
V
mV
V
mV
mV
%
%
Ω
Ω
µA
µA
V
V
l
Falling
Hysteresis
VISP = 12V
Rising
Falling
VEN/UVLO = 1.1V
VFB = 0.4V, VSS = 0V
VFB = 0.1V, VSS = 2V
l
l
l
l
8
–12
10
1
12
–8
200
200
15
1.5
Rev. B
For more information www.analog.com
5
LT8390A
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 12V, VEN/UVLO = 1.5V unless otherwise noted.
PARAMETER
Oscillator
RT Pin Voltage
Switching Frequency
SYNC Frequency
SYNC/SPRD Input Bias Current
SYNC/SPRD Threshold Voltage
Highest Spread Spectrum Above Oscillator Frequency
Region Transition
Buck-Boost to Boost (VIN /VOUT)
Boost to Buck-Boost (VIN /VOUT)
Buck to Buck-Boost (VIN /VOUT)
Buck-Boost to Buck (VIN /VOUT)
Peak-Buck to Peak-Boost (VIN /VOUT)
Peak-Boost to Peak-Buck (VIN /VOUT)
NMOS Drivers
TG1, TG2 Gate Driver On-Resistance
Gate Pull-Up
Gate Pull-Down
BG1, BG2 Gate Driver On-Resistance
Gate Pull-Up
Gate Pull-Down
TG1, TG2 Rise Time
TG1, TG2 Fall Time
BG1, BG2 Rise Time
BG1, BG2 Fall Time
TG Off to BG On Delay
BG Off to TG On Delay
TG1 Minimum Duty Cycle in Buck Region
TG1 Maximum Duty Cycle in Buck Region
TG1 Fixed Duty Cycle in Buck-Boost Region
BG2 Fixed Duty Cycle in Buck-Boost Region
BG2 Minimum Duty Cycle in Boost Region
BG2 Maximum Duty Cycle in Boost Region
CONDITIONS
RT = 100kΩ
VSYNC/SPRD = 0V, RT = 226kΩ
VSYNC/SPRD = 0V, RT = 100kΩ
VSYNC/SPRD = 0V, RT = 59.0kΩ
VSYNC/SPRD = 5V
VSYNC/SPRD = 5V
l
645
1290
1900
600
–0.1
0.4
21
0.73
0.83
1.23
1.31
0.96
1.00
V(BST-SW) = 5V
VINTVCC = 5V
CL = 3.3nF, 10% to 90%
CL = 3.3nF, 90% to 10%
CL = 3.3nF, 10% to 90%
CL = 3.3nF, 90% to 10%
CL = 3.3nF
CL = 3.3nF
Peak-Buck Current Mode
Peak-Buck Current Mode
Peak-Boost Current Mode
Peak-Buck Current Mode
Peak-Boost Current Mode
Peak-Boost Current Mode
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT8390AE is guaranteed to meet performance specifications
from 0°C to 125°C operating junction temperature. Specifications over
the –40°C to 125°C operating junction temperature range are assured by
design, characterization and correlation with statistical process controls.
The LT8390AI is guaranteed over the –40°C to 125°C operating junction
6
MIN
TYP
MAX
UNITS
23
725
1430
2100
2100
0.1
1.5
25
V
kHz
kHz
kHz
kHz
µA
V
%
0.75
0.85
1.25
1.33
0.98
1.02
0.77
0.87
1.27
1.35
1.00
1.04
1.00
685
1360
2000
0
2.6
1.4
Ω
Ω
3.2
1.2
25
20
25
20
25
25
10
90
80
20
10
90
Ω
Ω
ns
ns
ns
ns
ns
ns
%
%
%
%
%
%
temperature range. The LT8390AJ and LT8390AH are guaranteed over
the –40°C to 150°C operating junction temperature range. High junction
temperatures degrade operating lifetimes. Operating lifetime is derated at
junction temperatures greater than 125°C.
Note 3: The LT8390A includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 150°C when overtemperature protection is active.
Continuous operation above the specified absolute maximum operating
junction temperature may impair device reliability.
Rev. B
For more information www.analog.com
LT8390A
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency vs Load Current
(Buck Region)
TA = 25°C, unless otherwise noted.
Efficiency vs Load Current
(Buck-Boost Region)
Efficiency vs Load Current
(Boost Region)
90
90
90
80
80
80
70
60
50
0.5
1
1.5 2 2.5 3
LOAD CURRENT (A)
3.5
60
50
FRONT PAGE APPLICATION
VIN = 24V, VOUT = 12V, fSW = 2MHz
0
70
40
4
0
0.5
1
8390a G01
IL
2A/DIV
VSW2
20V/DIV
IL
2A/DIV
VOUT
500mV/DIV
VOUT
500mV/DIV
8390 G04
200ns/DIV
FRONT PAGE APPLICATION
VIN = 24V, IOUT = 2A
3.0
2.5
10
2.0
IQ (µA)
12
8
1.0
4
0.5
2
3
4
5
LOAD CURRENT (A)
6
7
0
0.5
1
1.5 2 2.5 3
LOAD CURRENT (A)
3.5
4
8390a G03
VSW1
20V/DIV
VSW2
20V/DIV
IL
2A/DIV
VOUT
500mV/DIV
200ns/DIV
FRONT PAGE APPLICATION
VIN = 8V, IOUT = 2A
8390 G05
VIN Shutdown Current
2.8
0.0
–50 –25
8390 G06
VIN Quiescent Current
2.6
VIN = 60V
1.5
6
1
FRONT PAGE APPLICATION
VIN = 8V, VOUT = 12V, fSW = 2MHz
Switching Waveforms
(Boost Region)
200ns/DIV
FRONT PAGE APPLICATION
VIN = 12V, IOUT = 2A
VOUT vs IOUT (CV/CC)
0
40
4
VSW1
20V/DIV
VSW2
20V/DIV
OUTPUT VOLTAGE (V)
3.5
Switching Waveforms
(Buck-Boost Region)
VSW1
20V/DIV
2
60
8390a G02
Switching Waveforms
(Buck Region)
14
1.5 2 2.5 3
LOAD CURRENT (A)
70
50
FRONT PAGE APPLICATION
VIN = 12V, VOUT = 12V, fSW = 2MHz
IQ (mA)
40
EFFICIENCY (%)
100
EFFICIENCY (%)
100
EFFICIENCY (%)
100
VIN = 12V
VIN = 60V
2.4
VIN = 12V
2.2
VIN = 4V
2.0
VIN = 4V
0
25 50 75 100 125 150
TEMPERATURE (°C)
1.8
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
8390a G07
8390a G08
8390a G09
Rev. B
For more information www.analog.com
7
LT8390A
TYPICAL PERFORMANCE CHARACTERISTICS
5.15
INTVCC Voltage vs Temperature
5.15
5.10
5.10
5.05
5.05
TA = 25°C, unless otherwise noted.
INTVCC Voltage vs VIN
4.0
INTVCC UVLO Threshold
3.9
IINTVCC = 0mA
5.00
IINTVCC = 80mA
IINTVCC = 20mA
VINTVCC (V)
VINTVCC (V)
VINTVCC (V )
3.8
5.00
4.95
4.95
4.90
4.90
RISING
3.7
3.6
FALLING
3.5
3.4
4.85
–50 –25
0
4.85
25 50 75 100 125 150
TEMPERATURE (°C)
3.3
0
10
20
30
VIN (V)
40
50
VREF Voltage vs Temperature
2.03
2.03
2.02
2.02
IVREF = 100µA
2.00
1.99
IVREF = 1mA
1.98
1.95
2.01
VREF (V)
VREF (V)
1.99
VREF UVLO Threshold
2.00
VREF (V)
2.04
2.00
RISING
1.85
FALLING
1.80
1.75
1.97
0
1.90
1.98
1.97
1.96
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
8390a G12
VREF Voltage vs VIN
2.04
IVREF = 0mA
0
8390a G11
8390a G10
2.01
3.2
–50 –25
60
1.96
25 50 75 100 125 150
TEMPERATURE (°C)
0
10
20
30
VIN (V)
40
50
1.70
–50 –25
60
0
25 50 75 100 125 150
TEMPERATURE (°C)
8390a G14
8390a G13
EN/UVLO Enable Threshold
8390a G15
EN/UVLO Hysteresis Current
1.240
CTRL Latch-Off Threshold
0.40
3.0
1.235
2.8
1.230
0.35
RISING
RISING
1.220
FALLING
1.215
1.210
2.6
VCTRL (V)
IHYS (µA)
VEN/UVLO (V)
1.225
2.4
0.30
FALLING
0.25
2.2
1.205
1.200
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
2.0
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
0.20
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
8390a G18
8390a G16
8
8390a G17
Rev. B
For more information www.analog.com
LT8390A
TYPICAL PERFORMANCE CHARACTERISTICS
106
125
V(ISP-ISN) (mV)
75
50
25
0
106
104
104
102
102
100
98
96
0
0.25 0.50 0.75 1 1.25 1.50 1.75
VCTRL (V)
94
2
0
10
20
30
VISP (V)
8390a G19
1.02
80
1.01
60
0.99
20
0.98
Maximum Current Sense
vs Temperature
VIN = 4V
VIN = 12V
VIN = 60V
0
60
55
50
45
40
35
30
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
1.15
0.35
0
25 50 75 100 125 150
TEMPERATURE (°C)
PGOOD Thresholds
20
15
RISING
RISING
VFB (V)
0.30
FALLING
0.25
0.20
0.15
25 50 75 100 125 150
TEMPERATURE (°C)
BUCK
BOOST
8390a G24
FB Short Threshold
0.40
0
8390a G21
8390a G23
FB Overvoltage Threshold
0.95
25 50 75 100 125 150
TEMPERATURE (°C)
65
0.97
–50 –25
1.20
1.00
0
70
8390a G22
FALLING
ISP = 0V
ISP = 12V
ISP = 60V
94
–50 –25
60
1.00
40
0
0.96 0.97 0.98 0.99 1.00 1.01 1.02 1.03 1.04
VFB (V)
VFB (V)
50
CURRENT LIMIT (mV)
100
VFB (V)
V(ISP-ISN) (mV)
1.03
0.90
–50 –25
40
FB Regulation vs Temperature
120
1.05
98
8390a G20
V(ISP-ISN) Regulation vs VFB
1.10
100
96
THRESHOLD OFFSET (%)
V(ISP-ISN) (mV)
100
V(ISP-ISN) Regulation
vs Temperature
V(ISP-ISN) Regulation vs VISP
V(ISP-ISN) (mV)
V(ISP-ISN) Regulation vs VCTRL
TA = 25°C, unless otherwise noted.
0.10
–50 –25
UPPER RISING
10
UPPER FALLING
5
0
–5
LOWER RISING
–10
LOWER FALLING
–15
0
25 50 75 100 125 150
TEMPERATURE (°C)
8390a G25
–20
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
8390a G27
8390a G26
Rev. B
For more information www.analog.com
9
LT8390A
TYPICAL PERFORMANCE CHARACTERISTICS
15.0
12.5
1.00
10.0
0.75
5.0
0.25
2.5
20
40
60
V(ISP-ISN) (mV)
80
100
PULL-UP
7.5
0.50
0
2.5
SWITCHING FREQUENCY (MHz)
1.25
0
Oscillator Frequency
vs Temperature
SS Current vs Temperature
ISS (µA)
VISMON (V)
1.50
ISMON Voltage vs V(ISP-ISN)
TA = 25°C, unless otherwise noted.
0.0
–50 –25
PULL-DOWN
0
25 50 75 100 125 150
TEMPERATURE (°C)
8390a G28
RT = 59.0k
2.0
RT = 100k
1.5
1.0
RT = 226k
0.5
0
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
8390a G30
8390a G29
10
Rev. B
For more information www.analog.com
LT8390A
PIN FUNCTIONS
BG1: Buck Side Bottom Gate Drive. Drives the gate of
buck side bottom N-channel MOSFET with a voltage swing
from ground to INTVCC.
BST1: Buck Side Bootstrap Floating Driver Supply. The
BST1 pin has an integrated bootstrap Schottky diode from
the INTVCC pin and requires an external bootstrap capacitor to the SW1 pin. The BST1 pin swings from a diode
voltage drop below INTVCC to (VIN + INTVCC).
SW1: Buck Side Switch Node. The SW1 pin swings from
a Schottky diode voltage drop below ground up to VIN.
TG1: Buck Side Top Gate Drive. Drives the gate of buck
side top N-channel MOSFET with a voltage swing from
SW1 to BST1.
LSP: Positive Terminal of the Buck Side Inductor Current
Sense Resistor (RSENSE). Ensure accurate current sense
with Kelvin connection.
LSN: Negative Terminal of the Buck Side Inductor Current
Sense Resistor (RSENSE). Ensure accurate current sense
with Kelvin connection.
VIN: Input Supply. The VIN pin must be tied to the power
input to determine the buck, buck-boost, or boost operation regions. Locally bypass this pin to ground with a
minimum 1µF ceramic capacitor.
INTVCC: Internal 5V Linear Regulator Output. The INTVCC
linear regulator is supplied from the VIN pin, and powers the internal control circuitry and gate drivers. Locally
bypass this pin to ground with a minimum 4.7µF ceramic
capacitor.
EN/UVLO: Enable and Undervoltage Lockout. Force the
pin below 0.3V to shut down the part and reduce VIN quiescent current below 2µA. Force the pin above 1.233V for
normal operation. The accurate 1.220V falling threshold
can be used to program an undervoltage lockout (UVLO)
threshold with a resistor divider from VIN to ground. An
accurate 2.5µA pull-down current allows the programming
of VIN UVLO hysteresis. If neither function is used, tie this
pin directly to VIN.
TEST: Factory Test. This pin is used for testing purpose
only and must be directly connected to ground for the
part to operate properly.
LOADEN: Load Switch Enable Input. The LOADEN pin is
used to control the ON/OFF of the high side PMOS load
switch. If the load switch control is not used, tie this pin
to VREF or INTVCC. Forcing the pin low turns off TG1 and
TG2, turns on BG1 and BG2, disconnects the VC pin from
all internal loads, and turns off LOADTG.
VREF: Voltage Reference Output. The VREF pin provides
an accurate 2V reference capable of supplying 1mA current. Locally bypass this pin to ground with a 0.47µF
ceramic capacitor.
CTRL: Control Input for ISP/ISN Current Sense Threshold.
The CTRL pin is used to program the ISP/ISN current
limit:
IIS(MAX) =
Min ( VCTRL − 0.25V,1V )
10 • RIS
The VCTRL can be set by an external voltage reference or
a resistor divider from VREF to ground. For 0.3V ≤ VCTRL
≤ 1.15V, the current sense threshold linearly goes up
from 5mV to 90mV. For VCTRL ≥ 1.35V, the current sense
threshold is constant at 100mV full scale value. For 1.15V
≤ VCTRL ≤ 1.35V, the current sense threshold smoothly
transitions from the linear function of VCTRL to the 100mV
constant value. Tie CTRL to VREF for the 100mV full scale
threshold. Force the pin below 0.3V to stop switching.
ISP: Positive Terminal of the ISP/ISN Current Sense
Resistor (RIS). Ensure accurate current sense with Kelvin
connection.
ISN: Negative Terminal of the ISP/ISN Current Sense
Resistor (RIS). Ensure accurate current sense with Kelvin
connection.
Rev. B
For more information www.analog.com
11
LT8390A
PIN FUNCTIONS
ISMON: ISP/ISN Current Sense Monitor Output. The
ISMON pin generates a voltage that is equal to ten times
V(ISP-ISN) plus 0.25V offset voltage. For parallel applications, tie the master LT8390A ISMON pin to the slave
LT8390A CTRL pin.
PGOOD: Power Good Open Drain Output. The PGOOD
pin is pulled low when the FB pin is within ±10% of the
final regulation voltage. To function, the pin requires an
external pull-up resistor.
SS: Soft-Start Timer Setting. The SS pin is used to set
soft-start timer by connecting a capacitor to ground. An
internal 12.5µA pull-up current charging the external SS
capacitor gradually ramps up FB regulation voltage. A
22nF capacitor is recommended on this pin. Any UVLO or
thermal shutdown immediately pulls SS pin to ground and
stops switching. Using a single resistor from SS to VREF,
the LT8390A can be set in three different fault protection
modes during output short-circuit condition: hiccup (no
resistor), latch-off (499kΩ), and keep-running (100kΩ).
See more details in the Applications Information section.
FB: Voltage Loop Feedback Input. The FB pin is used for
constant-voltage regulation and output fault protection.
The internal error amplifier with its output VC regulates
VFB to 1.00V through the DC/DC converter. During output
short-circuit (VFB < 0.25V) condition, the part gets into
one fault mode per customer setting. During an overvoltage (VFB > 1.1V) condition, the part turns off all TG1, BG1,
TG2, BG2, and LOADTG.
VC: Error Amplifier Output to Set Inductor Current
Comparator Threshold. The VC pin is used to compensate the control loop with an external RC network. During
LOADEN low state, the VC pin is disconnected from all
internal loads to store its voltage information.
RT: Switching Frequency Setting. Connect a resistor from
this pin to ground to set the internal oscillator frequency
from 600kHz to 2MHz.
SYNC/SPRD: Switching Frequency Synchronization or
Spread Spectrum. Ground this pin for switching at internal oscillator frequency. Apply a clock signal for external
frequency synchronization. Tie to INTVCC for 25% triangle
spread spectrum above internal oscillator frequency.
LOADTG: High Side PMOS Load Switch Top Gate Drive.
A buffered and inverted version of the LOADEN input signal, the LOADTG pin drives an external high side PMOS
load switch with a voltage swing from the higher voltage
of (VOUT-5V) and 1.2V to VOUT. Leave this pin unconnected
if not used.
VOUT: Output Supply. The VOUT pin must be tied to the
power output to determine the buck, buck-boost, or boost
operation regions. The VOUT pin also serves as positive
rail for the LOADTG drive. Locally bypass this pin to
ground with a minimum 1µF ceramic capacitor.
TG2: Boost Side Top Gate Drive. Drives the gate of boost
side top N-Channel MOSFET with a voltage swing from
SW2 to BST2.
SW2: Boost Side Switch Node. The SW2 pin swings from
a Schottky diode voltage drop below ground to VOUT.
BST2: Boost Side Bootstrap Floating Driver Supply. The
BST2 pin has an integrated bootstrap Schottky diode from
the INTVCC pin and requires an external bootstrap capacitor to the SW2 pin. The BST2 pin swings from a diode
voltage drop below INTVCC to (VOUT + INTVCC).
BG2: Boost Side Bottom Gate Drive. Drives the gate of
boost side bottom N-channel MOSFET with a voltage
swing from ground to INTVCC.
GND (Exposed Pad): Ground. Solder the exposed pad
directly to the ground plane.
12
Rev. B
For more information www.analog.com
LT8390A
BLOCK DIAGRAM
LSN
VIN
INTVCC
LSP
INTVCC
+
5V LDO
–
VREF
+
A1
–
2V REF
BST1
A3
TG1
PEAK_BUCK
SW1
BUCK
LOGIC
INTVCC
LOADON
RT
OSC
SYNC/SPRD
+
–
0.3V
CTRL
ISMON
BG1
VOS
1X
EN/UVLO
1.220V
+
–
FBOV
VIS
VOUT/BST2
VIN/BST1
CHARGE
CONTROL
FB
1.1V
INHIBIT
SWITCH
–
+
BG2
+
–
ISOC
2.5µA
LOADON
VISP-ISN
0.75V
PEAK_BOOST
BOOST
LOGIC
INTVCC
SW2
TG2
+
–
LOADEN
TEST
VOUT
LOADON
+
–
0.25V
FB
SHORT
BST2
VREF
12.5µA
LOADTG
PGOOD
A4
10µA
VOUT –5V
+
–
+
–
1.1V
FAULT
LOGIC
FB
EA2
1.25µA
FB
1V
+
+
FB
CTRL
1.25V
–
LOADON
0.9V
SS
INTVCC
+
EA1 +
–
VC
GND
+
VIS
+
A2=10
–
ISP
ISN
0.25V
8390a BD
Rev. B
For more information www.analog.com
13
LT8390A
OPERATION
The LT8390A is a current mode DC/DC controller that can
regulate output voltage, input or output current from input
voltage above, below, or equal to the output voltage. The
ADI proprietary peak-buck peak-boost current mode control scheme uses a single inductor current sense resistor and provides smooth transition between buck region,
buck-boost region, and boost region. Its operation is best
understood by referring to the Block Diagram.
VIN
VOUT
A
TG1
SW1
RSENSE
D
L
B
BG1
TG2
SW2
C
BG2
8390a F01
Figure 1. Simplified Diagram of the Power Switches
Power Switch Control
Figure 1 shows a simplified diagram of how the four
power switches A, B, C, and D are connected to the inductor L, the current sense resistor RSENSE, power input VIN,
power output VOUT, and ground. The current sense resistor RSENSE connected to the LSP and LSN pins provides
inductor current information for both peak current mode
control and reverse current detection in buck region,
buck-boost region, and boost region. Figure 2 shows the
current mode control as a function of VIN/VOUT ratio and
Figure 3 shows the operation region as a function of VIN/
VOUT ratio. The power switches are properly controlled
to smoothly transition between modes and regions.
Hysteresis is added to prevent chattering between modes
and regions.
There are total four states: (1) peak-buck current mode
control in buck region, (2) peak-buck current mode control in buck-boost region, (3) peak-boost current mode
control in buck-boost region, and (4) peak-boost current
mode control in boost region. The following sections
give detailed description for each state with waveforms,
in which the shoot-through protection dead time between
switches A and B, between switches C and D are ignored
for simplification.
PEAK-BUCK
PEAK-BOOST
0.98 1.00 1.02
VIN/VOUT
8390a F02
Figure 2. Current Mode vs VIN/VOUT Ratio
(1)
BUCK
(3)
(2)
BUCK-BOOST
(2)
BOOST
(4)
0.75
0.85
1.00
VIN/VOUT
1.25
1.33
8390a F03
Figure 3. Operation Region vs VIN/VOUT Ratio
14
Rev. B
For more information www.analog.com
LT8390A
OPERATION
(1) Peak-Buck in Buck Region (VIN >> VOUT)
(2) Peak-Buck in Buck-Boost Region (VIN ~> VOUT)
When VIN is much higher than VOUT, the LT8390A uses
peak-buck current mode control in buck region (Figure 4).
Switch C is always off and switch D is always on. At the
beginning of every cycle, switch A is turned on and the
inductor current ramps up. When the inductor current hits
the peak buck current threshold commanded by VC voltage at buck current comparator A3 during (A+D) phase,
switch A is turned off and switch B is turned on for the
rest of the cycle. Switches A and B will alternate, behaving
like a typical synchronous buck regulator.
When VIN is slightly higher than VOUT, the LT8390A uses
peak-buck current mode control in buck-boost region
(Figure 5). Switch C is always turned on for the beginning 20% cycle and switch D is always turned on for the
remaining 80% cycle. At the beginning of every cycle,
switches A and C are turned on and the inductor current
ramps up. After 20% cycle, switch C is turned off and
switch D is turned on, and the inductor keeps ramping
up. When the inductor current hits the peak buck current
threshold commanded by VC voltage at buck current comparator A3 during (A+D) phase, switch A is turned off and
switch B is turned on for the rest of the cycle.
A
A
B
B
C
100% OFF
C
D
100% ON
D
20%
20%
80%
IL
IL
A+D
B+D
A+D
B+D
A+D
A+C
A+D
B+D
A+C
B+D
8390a F05
8390a F04
Figure 4. Peak-Buck in Buck Region (VIN >> VOUT)
80%
Figure 5. Peak-Buck in Buck-Boost Region (VIN ~> VOUT)
Rev. B
For more information www.analog.com
15
LT8390A
OPERATION
(3) Peak-Boost in Buck-Boost Region (VIN
(
VOUT • VIN(MAX) − VOUT
VIN(MIN)
2
(
• VOUT − VIN(MIN)
f •IOUT(MAX) • ΔIL % • VOUT
2
)
⎛ 50mV ΔIL(BOOST) ⎞ VIN(MIN)
IOUT(MAX _BOOST) = ⎜
−
⎟⎠ • V
2
⎝ RSENSE
OUT
where ∆IL(BOOST) is peak-to-peak inductor ripple current
in boost region and can be calculated as:
where:
ΔIL % =
In boost region, the lowest maximum average load current happens at VIN(MIN) and can be calculated as:
ΔIL
ΔIL(BOOST) =
(
VIN(MIN) • VOUT − VIN(MIN)
f • L • VOUT
)
In buck region, the lowest maximum average load current
happens at VIN(MAX) and can be calculated as:
IL(AVG)
f is switching frequency
⎛ 50mV ΔIL(BUCK) ⎞
IOUT(MAX _BUCK) = ⎜
−
⎟⎠
2
⎝ RSENSE
VIN(MIN) is minimum input voltage
VIN(MAX) is maximum input voltage
where ∆IL(BUCK) is peak-to-peak inductor ripple current in
buck region and can be calculated as:
VOUT is output voltage
IOUT(MAX) is maximum output current
Slope compensation provides stability in constant frequency current mode control by preventing subharmonic
oscillations at certain duty cycles. The minimum inductance required for stability when duty cycles are larger
than 50% can be calculated as:
L>
10 • VOUT • RSENSE
f
(
VOUT • VIN(MAX) − VOUT
f • L • VIN(MAX)
)
The maximum current sense RSENSE in boost region is:
RSENSE(BOOST) =
2 • 50mV • VIN(MIN)
2 •IOUT(MAX) • VOUT + ΔIL(BOOST) • VIN(MIN)
The maximum current sense RSENSE in buck region is
For high efficiency, choose an inductor with low core loss,
such as ferrite. Also, the inductor should have low DC
resistance to reduce the I2R losses, and must be able to
handle the peak inductor current without saturating. To
minimize radiated noise, use a shielded inductor.
20
ΔIL(BUCK) =
RSENSE(BUCK) =
2 • 50mV
2 •IOUT(MAX) + ΔIL(BUCK)
The final RSENSE value should be lower than the calculated
RSENSE in both buck and boost regions. A 20% to 30%
margin is usually recommended. Always choose a low
ESL current sense resistor.
Rev. B
For more information www.analog.com
LT8390A
APPLICATIONS INFORMATION
Power MOSFET Selection
RL is the maximum DCR resistor of inductor at 25°C
The LT8390A requires four external N-channel power
MOSFETs, two for the top switches (switches A and D
shown in Figure 1) and two for the bottom switches
(switches B and C shown in Figure 1). Important parameters for the power MOSFETs are the breakdown voltage VBR(DSS), threshold voltage VGS(TH), on-resistance
RDS(ON), reverse transfer capacitance CRSS and maximum
current IDS(MAX).
The RDS(ON) and DCR increase at higher junction
temperatures and the process variation have been
included in the calculation above.
Since the gate drive voltage is set by the 5V INTVCC
supply, logic-level threshold MOSFETs must be used in
LT8390A applications. Switching four MOSFETs at higher
frequency like 2MHz, the substantial gate charge current
from INTVCC can be estimated as:
(
IINTVCC = f • QgA + QgB + QgC + QgD
)
where:
f is the switching frequency
QgA, QgB, QgC, QgD are the total gate charges of
MOSFETs A, B, C, D
Make sure the total required INTVCC current not exceeding the INTVCC current limit in the data sheet. Typically,
MOSFETs with less than 10nC Qg are recommended.
The LT8390A uses the VIN/VOUT ratio to transition between
modes and regions. Bigger IR drop in the power path
caused by improper MOSFET and inductor selection may
prevent the LT8390A from smooth transition. To ensure
smooth transitions between buck, buck-boost, and boost
modes of operation, choose low RDS(ON) MOSFETs and
low DCR inductor to satisfy:
IOUT(MAX) ≤
0.025 • VOUT
R A,B + RC,D + RSENSE + RL
where:
2
⎛ IOUT(MAX) • VOUT ⎞
PA(BOOST) = ⎜
⎟⎠ • ρT • RDS(ON)
V
⎝
IN
where ρT is a normalization factor (unity at 25°C) accounting for the significant variation in on-resistance with
temperature, typically 0.4%/°C as shown in Figure 11. For
a maximum junction temperature of 125°C, using a value
of ρT = 1.5 is reasonable.
Switch B operates in buck region as the synchronous
rectifier. Its power dissipation at maximum output current is given by:
PB(BUCK) =
PC(BOOST) =
( VOUT − VIN ) • VOUT •I
VIN
2
• RDS(ON) + k • VOUT
2
OUT(MAX)
3
•
• ρT
IOUT(MAX)
VIN
• CRSS • f
2.0
1.5
1.0
0.5
0
–50
RA,B is the maximum RDS(ON) of MOSFETs A or B at 25°C
RC,D is the maximum RDS(ON) of MOSFETs C or D at
25°C
VIN − VOUT
•IOUT(MAX)2 • ρT • RDS(ON)
VIN
Switch C operates in boost region as the control switch.
Its power dissipation at maximum current is given by:
ρT NORMALIZED ON-RESISTANCE (Ω)
To achieve 2MHz operation, the power MOSFET selection is critical. With typical 25ns shoot-through protection
deadtime, high performance power MOSFETs with low Qg
and low RDS(ON) must be used.
In order to select the power MOSFETs, the power dissipated by the device must be known. For switch A, the
maximum power dissipation happens in boost region,
when it remains on all the time. Its maximum power dissipation at maximum output current is given by:
50
100
0
JUNCTION TEMPERATURE (°C)
150
8390a F11
Figure 11. Normalized RDS(ON) vs Temperature
For more information www.analog.com
Rev. B
21
LT8390A
APPLICATIONS INFORMATION
where CRSS is usually specified by the MOSFET manufacturers. The constant k, which accounts for the loss caused
by reverse recovery current, is inversely proportional to
the gate drive current and has an empirical value of 1.7.
For switch D, the maximum power dissipation happens in
boost region, when its duty cycle is higher than 50%. Its
maximum power dissipation at maximum output current
is given by:
PD(BOOST) =
VOUT
•IOUT(MAX)2 • ρT • RDS(ON)
VIN
For the same output voltage and current, switch A has the
highest power dissipation and switch B has the lowest
power dissipation unless a short occurs at the output.
From a known power dissipated in the power MOSFET, its
junction temperature can be obtained using the following
formula:
TJ = TA + P • RTH(JA)
The junction-to-ambient thermal resistance RTH(JA)
includes the junction-to-case thermal resistance RTH(JC)
and the case-to-ambient thermal resistance RTH(CA). This
value of TJ can then be compared to the original, assumed
value used in the iterative calculation process.
Optional Schottky Diode (DB, DD) Selection
The optional Schottky diodes DB (in parallel with switch
B) and DD (in parallel with switch D) conduct during the
dead time between the conduction of the power MOSFET
switches. They are intended to prevent the body diode
of synchronous switches B and D from turning on and
storing charge during the dead time. In particular, DB
significantly reduces reverse recovery current between
switch B turn-off and switch A turn-on, and DD significantly reduces reverse recovery current between switch
D turn-off and switch C turn-on. They improve converter
efficiency and reduce switch voltage stress. In order for
the diode to be effective, the inductance between it and
the synchronous switch must be as small as possible,
mandating that these components be placed adjacently.
22
CIN and COUT Selection
Input and output capacitance is necessary to suppress
voltage ripple caused by discontinuous current moving
in and out the regulator. A parallel combination of capacitors is typically used to achieve high capacitance and low
equivalent series resistance (ESR). Dry tantalum, special
polymer, aluminum electrolytic and ceramic capacitors are
all available in surface mount packages. Capacitors with
low ESR and high ripple current ratings, such as OS-CON
and POSCAP are also available.
Ceramic capacitors should be placed near the regula-tor
input and output to suppress high frequency switching
spikes. Ceramic capacitors, of at least 1µF, should also
be placed from VIN to GND and VOUT to GND as close to
the LT8390A pins as possible. Due to their excellent low
ESR characteristics, ceramic capacitors can significantly
reduce input ripple voltage and help reduce power loss
in the higher ESR bulk capacitors. X5R or X7R dielectrics
are preferred, as these materials retain their capacitance
over wide voltage and temperature ranges. Many ceramic
capacitors, particularly 0805 or 0603 case sizes, have
greatly reduced capacitance at the desired operating
voltage.
Input Capacitance CIN: Discontinuous input current is
highest in the buck region due to the switch A toggling
on and off. Make sure that the CIN capacitor network has
low enough ESR and is sized to handle the maximum RMS
current. In buck region, the input RMS current is given by:
IRMS ≈ IOUT(MAX) •
VOUT
VIN
•
−1
VIN
VOUT
The formula has a maximum at VIN = 2VOUT, where IRMS
= IOUT(MAX) /2. This simple worst-case condition is commonly used for design because even significant deviations
do not offer much relief.
Output Capacitance COUT: Discontinuous current shifts
from the input to the output in the boost region. Make sure
that the COUT capacitor network is capable of reducing the
output voltage ripple. The effects of ESR and the bulk
capacitance must be considered when choosing the right
capacitor for a given output ripple voltage. The maximum
Rev. B
For more information www.analog.com
LT8390A
APPLICATIONS INFORMATION
steady state ripple due to charging and discharging the
bulk capacitance is given by:
ΔVCAP(BOOST) =
ΔVCAP(BUCK) =
(
IOUT(MAX) • VOUT − VIN(MIN)
COUT • VOUT • f
)
⎛
⎞
V
VOUT • ⎜ 1− OUT ⎟
⎝ VIN(MAX) ⎠
8 • L • f2 • COUT
The maximum steady ripple due to the voltage drop
across the ESR is given by:
ΔVESR(BOOST) =
VOUT •IOUT(MAX)
VIN(MIN)
• ESR
⎛
⎞
V
VOUT • ⎜ 1− OUT ⎟
⎝ VIN(MAX) ⎠
• ESR
ΔVESR(BUCK) =
L•f
INTVCC Regulator
An internal P-channel low dropout regulator produces 5V
at the INTVCC pin from the VIN supply pin. The INTVCC powers internal circuitry and gate drivers in the LT8390A. The
INTVCC regulator can supply a peak current of 145mA and
must be bypassed to ground with a minimum of 4.7µF
ceramic capacitor. Good local bypass is necessary to supply
the high transient current required by MOSFET gate drivers.
Higher input voltage applications with large MOSFETs being
driven at higher switching frequencies may cause the maximum junction temperature rating for the LT8390A to be
exceeded. The system supply current is normally dominated
by the gate charge current. Additional external loading of the
INTVCC also needs to be taken into account for the power dissipation calculation. The total LT8390A power dissipation in
this case is VIN • IINTVCC, and overall efficiency is lowered. The
junction temperature can be estimated by using the equation:
Top Gate MOSFET Driver Supply (CBST1, CBST2)
The top MOSFET drivers, TG1 and TG2, are driven between
their respective SW and BST pin voltages. The boost voltages are biased from floating bootstrap capacitors CBST1
and CBST2, which are normally recharged through both the
external and internal bootstrap diodes when the respective
top MOSFET is turned off. External bootstrap diodes are
recommended because the internal bootstrap diodes are
not always strong enough to refresh top MOSFETs at 2MHz.
Both capacitors are charged to the same voltage as the
INTVCC voltage. The bootstrap capacitors CBST1 and CBST2,
need to store about 100 times the gate charge required by
the top switches A and D. In most applications, a 0.1µF to
0.47µF, X5R or X7R dielectric capacitor is adequate.
Programming VIN UVLO
A resistor divider from VIN to the EN/UVLO pin implements VIN undervoltage lockout (UVLO). The EN/UVLO
enable falling threshold is set at 1.220V with 13mV hysteresis. In addition, the EN/UVLO pin sinks 2.5µA when the
voltage on the pin is below 1.220V. This current provides
user programmable hysteresis based on the value of R1.
The programmable UVLO thresholds are:
R1+ R2
+ 2.5µA • R1
R2
R1+ R2
VIN(UVLO−) = 1.220V •
R2
VIN(UVLO+) = 1.233V •
Figure 12 shows the implementation of external shutdown control while still using the UVLO function. The
NMOS grounds the EN/UVLO pin when turned on, and
puts the LT8390A in shutdown with quiescent current
less than 2µA.
VIN
R1
EN/UVLO
LT8390A
TJ = TA + PD • θJA
where θJA (in °C/W) is the package thermal resistance.
To prevent maximum junction temperature from being
exceeded, the input supply current must be checked operating in continuous mode at maximum VIN.
R2
RUN/STOP
CONTROL
(OPTIONAL)
GND
8390a F12
Figure 12. VIN Undervoltage Lockout (UVLO)
Rev. B
For more information www.analog.com
23
LT8390A
APPLICATIONS INFORMATION
Programming Input or Output Current Limit
The input or output current limit can be programmed by
placing an appropriate value current sense resistor, RIS, in
the input or output power path. The voltage drop across
RIS is (Kelvin) sensed by the ISP and ISN pins. The CTRL
pin should be tied to a voltage higher than 1.35V to get
the full-scale 100mV (typical) threshold across the sense
resistor. The CTRL pin can be used to reduce the current
threshold to zero, although relative accuracy decreases
with the decreasing sense threshold. When the CTRL pin
voltage is between 0.3V and 1.15V, the current limit is:
IIS(MAX) =
VCTRL − 0.25V
10 • RIS
When VCTRL is between 1.15V and 1.35V the current limit
varies with VCTRL, but departs from the equation above
by an increasing amount as VCTRL increases. Ultimately,
when VCTRL is larger than 1.35V, the current limit no longer varies. The typical V(ISP-ISN) threshold vs VCTRL is
listed in Table 2.
Table 2. V(ISP-ISN) Threshold vs VCTRL
VCTRL (V)
V(ISP-ISN) (mV)
1.15
90
1.20
94.5
1.25
98
1.30
99.5
1.35
100
frequency is expected. If the current sense resistor RIS
is placed between power input and input bulk capacitor
(Figure 13a), or between output bulk capacitor and system output (Figure 14a), a filter is typically not necessary. If the RIS is placed between input bulk capacitor
and input decoupling capacitor (Figure 13b), or between
output decoupling capacitor and output bulk capacitor
(Figure 14b), a low pass filter formed by RF and CF is
recommended to reduce the current ripple and stabilize
the current loop. Since the bias currents of the ISP and
ISN pins are matched, no offset is introduced by RF. If
input or output current limit is not used, the ISP and ISN
pins should be shorted to VIN, VOUT, or ground.
ISMON Current Monitor
The ISMON pin provides a buffered monitor output of the
current flowing through the ISP/ISN current sense resistor, RIS. The VISMON voltage is calculated as V(ISP-ISN) • 10
+ 0.25V. Since the ISMON pin has the same 0.25V offset
as the CTRL pin, the master LT8390A ISMON pin can
be directly tied to the slave LT8390A CTRL pin for equal
current sharing in parallel applications.
RIS
FROM POWER
INPUT
+
ISN
ISP
LT8390A
8390a F13a
When VCTRL is larger than 1.35V, the current threshold
is regulated to:
IIS(MAX) =
100mV
RIS
(13a)
FROM POWER
INPUT
The CTRL pin should not be left open (tie to VREF if not
used). The CTRL pin can also be used in conjunction with
a thermistor to provide overtemperature protection for
the output load, or with a resistor divider to VIN to reduce
output power and switching current when VIN is low.
The presence of a time varying differential voltage ripple signal across the ISP and ISN pins at the switching
24
TO DRAIN OF
SWITCH A
RIS
+
RF
CF
TO DRAIN OF
SWITCH A
RF
ISN
ISP
LT8390A
8390a F13b
(13b)
Figure 13. Programming Input Current Limit
Rev. B
For more information www.analog.com
LT8390A
APPLICATIONS INFORMATION
FROM DRAIN OF
SWITCH D
RIS
TO SYSTEM
OUTPUT
+
ISN
ISP
LT8390A
Programming Output Voltage and Thresholds
The LT8390A has a voltage feedback pin FB that can be
used to program a constant-voltage output. The output
voltage can be set by selecting the values of R3 and R4
(Figure 15) according to the following equation:
8390a F14a
(14a)
RIS
FROM DRAIN OF
SWITCH D
RF
CF
RF
+
TO SYSTEM
OUTPUT
VOUT = 1V •
R3 + R4
R4
In addition, the FB pin also sets output overvoltage
threshold, output power good thresholds, and output
short threshold. For an application with small output
capacitors, the output voltage may overshoot a lot during
VOUT
ISN
ISP
LT8390A
R3
LT8390A
FB
8390a F14b
R4
(14b)
8390a F15
Figure 14. Programming Output Current Limit
Load Switch Control
The LOADEN and LOADTG pins provide high side PMOS
load switch control. The LOADEN pin accepts a logic level
ON/OFF signal and then drives the LOADTG pin to turn on
or off the high side PMOS load switch, thereby connecting or disconnecting the LT8390A power output from the
system output. When the LOADEN pin is forced low, the
LT8390A turns off TG1 and TG2, turns on BG1 and BG2,
disconnects the VC pin from all internal loads, and turns
off LOADTG. The LOADEN pin should not be left open (tie
to INTVCC or VREF if not used).
High Side PMOS Load Switch Selection
Figure 15. Feedback Resistor Connection
load transient event. Once the FB pin hits its overvoltage
threshold 1.1V, the LT8390A stops switching by turning
off TG1, BG1, TG2, and BG2, and also turns off LOADTG
to disconnect the output load for protection. The output
overvoltage threshold can be set as:
R3 + R4
R4
To provide the output short-circuit detection and protection, the output short falling threshold can be set as:
A high side PMOS load switch is recommended in some
LT8390A applications requiring load switch control. The
high side PMOS load switch is typically selected for drainsource voltage VDS, gate-source threshold voltage VGS(TH),
and continuous drain current ID. For proper operations,
VDS rating should exceed the output regulation voltage
set by the FB pin, the absolute value of VGS(TH) should
be less than 3V, and ID rating should be above IOUT(MAX).
VOUT(OVP) = 1.1V •
VOUT(SHORT) = 0.25V •
R3 + R4
R4
Power GOOD (PGOOD) Pin
The LT8390A provides an open-drain status pin, PGOOD,
which is pulled low when VFB is within ±10% of the 1.00V
regulation voltage. The PGOOD pin is allowed to be pulled
up by an external resistor to INTVCC or an external voltage
source of up to 6V.
Rev. B
For more information www.analog.com
25
LT8390A
APPLICATIONS INFORMATION
Soft-Start and Short-Circuit Protection
Loop Compensation
As shown in Figure 8 and explained in the Operation section, the SS pin can be used to program the output voltage soft-start by connecting an external capacitor from
the SS pin to ground. The internal 12.5µA pull-up current
charges up the capacitor, creating a voltage ramp on the
SS pin. As the SS pin voltage rises linearly from 0.25V
to 1V (and beyond), the output voltage rises smoothly
into its final voltage regulation. The soft-start time can
be calculated as:
The LT8390A uses an internal transconductance error
amplifier, the output of which, VC, compensates the control loop. The external inductor, output capacitor, and the
compensation resistor and capacitor determine the loop
stability.
tSS = 1V •
CSS
12.5µA
Make sure the CSS is at least five to ten times larger than
the compensation capacitor on the VC pin for a well-controlled output voltage soft-start. A 22nF ceramic capacitor
is a good starting point.
The SS pin is also used as a fault timer. Once an output
short-circuit fault is detected, a 1.25µA pull-down current
source is activated. Using a single resistor from the SS
pin to the VREF pin, the LT8390A can be set to three different fault protection modes: hiccup (no resistor), latch-off
(499k), and keep-running (100k).
With a 100k resistor in keep-running mode, the LT8390A
continues switching normally and regulates the current
into ground. With a 499k resistor in latch-off mode, the
LT8390A stops switching until the EN/UVLO pin is pulled
low and high to restart. With no resistor in hiccup mode,
the LT8390A enters low duty cycle auto-retry operation.
The 1.25µA pull-down current discharges the SS pin to
0.2V and then 12.5µA pull-up current charges the SS
pin up. If the output short-circuit condition has not been
removed when the SS pin reaches 1.75V, the 1.25µA pulldown current turns on again, initiating a new hiccup cycle.
This will continue until the fault is removed. Once the
output short-circuit condition is removed, the output will
have a smooth short-circuit recovery due to soft-start.
26
The inductor and output capacitor are chosen based on
performance, size and cost. The compensation resistor
and capacitor on the VC pin are set to optimize control
loop response and stability. For a typical voltage regulator
application, a 2.2nF compensation capacitor on the VC pin
is adequate, and a series resistor should always be used
to increase the slew rate on the VC pin to maintain tighter
output voltage regulation during fast transients on the
input supply of the converter.
Efficiency Considerations
The power efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Although all dissipative
elements in circuits produce losses, four main sources
account for most of the losses in LT8390A circuits:
1. DC I2R losses. These arise from the resistances of the
MOSFETs, sensing resistor, inductor and PC board
traces and cause the efficiency to drop at high output
currents.
2. Transition loss. This loss arises from the brief amount
of time switch A or switch C spends in the saturated
region during switch node transitions. It depends upon
the input voltage, load current, driver strength and
MOSFET capacitance, among other factors.
3. INTVCC current. This is the sum of the MOSFET driver
and control currents.
4. CIN and COUT loss. The input capacitor has the difficult job of filtering the large RMS input current to the
regulator in buck region. The output capacitor has the
difficult job of filtering the large RMS output current in
boost region. Both CIN and COUT are required to have
Rev. B
For more information www.analog.com
LT8390A
APPLICATIONS INFORMATION
low ESR to minimize the AC I2R loss and sufficient
capacitance to prevent the RMS current from causing
additional upstream losses in fuses or batteries.
5. Other losses. Schottky diode DB and DD are responsible for conduction losses during dead time and light
load conduction periods. Inductor core loss occurs
predominately at light loads. Switch A causes reverse
recovery current loss in buck region, and switch C
causes reverse recovery current loss in boost region.
When making adjustments to improve efficiency, the
input current is the best indicator of changes in efficiency. If you make a change and the input current
decreases, then the efficiency has increased. If there is
no change in the input current, then there is no change
in efficiency.
Place switch A and switch C as close to the controller as possible, keeping the PGND, BG and SW traces
short.
n
n
Keep the high dV/dT SW1, SW2, BST1, BST2, TG1 and
TG2 nodes away from sensitive small-signal nodes.
The path formed by switch A, switch B, DB and the
CIN capacitor should have short leads and PCB trace
lengths. The path formed by switch C, switch D, DD and
the COUT capacitor also should have short leads and
PCB trace lengths.
n
n
The output capacitor (–) terminals should be connected
as close as possible to the (–) terminals of the input
capacitor.
Connect the top driver bootstrap capacitor CBST1
closely to the BST1 and SW1 pins. Connect the top
driver bootstrap capacitor CBST2 closely to the BST2
and SW2 pins.
n
PC Board Layout Checklist
The basic PC board layout requires a dedicated ground
plane layer. Also, for high current, a multilayer board provides heat sinking for power components.
n
The ground plane layer should not have any traces and
it should be as close as possible to the layer with power
MOSFETs.
n
n
Route LSP and LSN traces together with minimum
PCB trace spacing. Avoid sense lines pass through
noisy areas, such as switch nodes. The filter capacitor
between LSP and LSN should be as close as possible
to the IC. Ensure accurate current sensing with Kelvin
connections at the RSENSE resistor. Low ESL sense
resistor is recommended.
Place CIN, switch A, switch B and DB in one compact
area. Place COUT, switch C, switch D and DD in one
compact area.
n
Use immediate vias to connect the components to the
ground plane. Use several large vias for each power
component.
n
Connect the VC pin compensation network close to the
IC, between VC and the signal ground. The capacitor
helps to filter the effects of PCB noise and output voltage ripple voltage from the compensation loop.
n
Use planes for VIN and VOUT to maintain good voltage
filtering and to keep power losses low.
n
Flood all unused areas on all layers with copper.
Flooding with copper will reduce the temperature rise
of power components. Connect the copper areas to any
DC net (VIN or GND).
n
Connect the input capacitors CIN and output capacitors
COUT closely to the power MOSFETs. These capacitors
carry the MOSFET AC current.
n
Connect the INTVCC bypass capacitor, CINTVCC, close to
the IC, between the INTVCC and the power ground. This
capacitor carries the MOSFET drivers’ current peaks.
Separate the signal and power grounds. All small-signal components should return to the exposed GND pad
from the bottom, which is then tied to the power GND
close to the sources of switch B and switch C.
n
Rev. B
For more information www.analog.com
27
LT8390A
TYPICAL APPLICATIONS
95% Efficient 48W (12V 4A) 2MHz Buck-Boost Voltage Regulator
VIN
6V TO 28V
CONTINUOUS
4V TO 56V
TRANSIENT
22µF
63V
4.7µF
100V
×2
L1
1µH
R1
5mΩ
M1
0.1µF
0.1µF
100V
×2
SW1 LSP
BST1
LSN
0.1µF
SW2
BST2
0.1µF
16V
×2
D2
D1
INTVCC
M2
R2
10mΩ
M4
BG1
BG2
INTVCC
22µF
16V
×2
22µF
16V
VOUT
12V
4A
M3
GND
TG1
VIN
TG2
LT8390A
VOUT
1µF
383k
169k
1µF
EN/UVLO
ISP
LOADTG
ISN
TEST
ISMON
133k
0.47µF
SSFM OFF
SYNC/SPRD
CTRL
100k
1µF 10
FB
ISMON
INTVCC
INTVCC
4.7µF
LOADEN
VREF
SS
22nF
PGOOD
RT
VC
10k
10
10k
SSFM ON
100k
PGOOD
59.0k
2MHz
110k
L1: WURTH 74437336010 1µH
M1, M2: INFINEON BSZ065NO6LS5
M3, M4: INFINEON BSZ033NE2LS5
D1, D2: NXP BAT46WJ
R1: Susumu KRL3216D-M-R005-F-T5
2.2nF
8390a TA02a
28
Rev. B
For more information www.analog.com
LT8390A
PACKAGE DESCRIPTION
FE Package
28-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1663 Rev L)
Exposed Pad Variation EB
9.60 – 9.80*
(.378 – .386)
4.75
(.187)
4.75
(.187)
28 27 26 2524 23 22 21 20 1918 17 16 15
6.60 ±0.10
4.50 ±0.10
2.74
(.108)
SEE NOTE 4
0.45 ±0.05
EXPOSED
PAD HEAT SINK
ON BOTTOM OF
PACKAGE
6.40
2.74
(.252)
(.108)
BSC
1.05 ±0.10
0.65 BSC
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
2. DIMENSIONS ARE IN MILLIMETERS
(INCHES)
3. DRAWING NOT TO SCALE
1 2 3 4 5 6 7 8 9 10 11 12 13 14
0.25
REF
1.20
(.047)
MAX
0° – 8°
0.65
(.0256)
BSC
0.195 – 0.30
(.0077 – .0118)
TYP
0.05 – 0.15
(.002 – .006)
FE28 (EB) TSSOP REV L 0117
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
Rev. B
For more information www.analog.com
29
LT8390A
PACKAGE DESCRIPTION
UFD Package
28-Lead Plastic QFN (4mm × 5mm)
(Reference LTC DWG # 05-08-1712 Rev C)
0.70 ±0.05
4.50 ±0.05
3.10 ±0.05
2.50 REF
2.65 ±0.05
3.65 ±0.05
PACKAGE OUTLINE
0.25 ±0.05
0.50 BSC
3.50 REF
4.10 ±0.05
5.50 ±0.05
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
4.00 ±0.10
(2 SIDES)
R = 0.05
TYP
0.75 ±0.05
PIN 1 NOTCH
R = 0.20 OR 0.35
× 45° CHAMFER
2.50 REF
R = 0.115
TYP
27
28
0.40 ±0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
5.00 ±0.10
(2 SIDES)
3.50 REF
3.65 ±0.10
2.65 ±0.10
(UFD28) QFN 0816 REV C
0.200 REF
0.00 – 0.05
0.25 ±0.05
0.50 BSC
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGHD-3).
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
30
Rev. B
For more information www.analog.com
LT8390A
REVISION HISTORY
REV
DATE
DESCRIPTION
A
09/17
Added H-Grade Temperature Option.
2, 6
Clarified Block Diagram.
13
Clarified Sense Resistors description in Route LSP and LSN traces bullet.
27
Added AEC-Q100 Qualified for Automotive Applications to Features section.
1
Added LT8390AJ to Operating Junction Temperature Range section.
2
Added “AUTOMOTIVE PRODUCTS**” and supplemental text to Ordering Information table.
3
Updated Note 2.
6
B
06/21
PAGE NUMBER
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications
subject to change without notice. No license For
is granted
implication or
otherwise under any patent or patent rights of Analog Devices.
more by
information
www.analog.com
31
LT8390A
TYPICAL APPLICATION
25W (5V 5A) 2MHz Buck-Boost Voltage Regulator
VIN
4.5V TO 20V
CONTINUOUS
4V TO 56V
TRANSIENT
22µF
63V
0.1µF
0.1µF
100V
×2
L1
0.33µH
R1
5mΩ
M1
SW1 LSP
BST1
LSN
0.1µF
SW2
BST2
INTVCC
M2
0.1µF
10V
×2
D2
D1
4.7µF
100V
×2
R2
10mΩ
M4
BG1
BG2
INTVCC
VOUT
5V
5A
47µF
10V
×2
47µF
10V
M3
GND
TG1
VIN
TG2
LT8390A
VOUT
1µF
383k
169k
1µF
EN/UVLO
ISP
LOADTG
ISN
TEST
ISMON
95.3k
0.47µF
INTVCC
INTVCC
4.7µF
LOADEN
VREF
SS
22nF
PGOOD
RT
VC
11k
40.2k
SSFM OFF
SYNC/SPRD
CTRL
105k
1µF 10Ω
FB
ISMON
10Ω
59k
2MHz
10k
SSFM ON
100k
PGOOD
L1: COILCRAFT XEL4020-331ME 0.33µH
M1, M2: INFINEON BSZ034N04LS
M3, M4: INFINEON BSZ033NE2LS5
D1, D2: NXP BAT46WJ
R1: SUSUMU KRL3216D-M-R005-F-T5
2.2nF
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT8390
60V Synchronous 4-Switch Buck-Boost Controller
with Spread Spectrum
VIN: 4V to 60V, VOUT: 0V to 60V, ±1.5% Voltage Accuracy, ±3% Current
Accuracy, TSSOP-28 and 4mm × 5mm QFN-28
LT8391
60V Synchronous 4-Switch Buck-Boost LED
Controller with Spread Spectrum
VIN: 4V to 60V, VOUT: 0V to 60V, ±1.5% Voltage Accuracy, ±3% Current
Accuracy, TSSOP-28 and 4mm × 5mm QFN-28
LT8391A
60V Synchronous 2MHz 4-Switch Buck-Boost LED
Controller with Spread Spectrum
VIN: 4V to 60V, VOUT: 0V to 60V, ±1.5% Voltage Accuracy, ±3% Current
Accuracy, TSSOP-28 and 4mm × 5mm QFN-28
LT3790
60V Synchronous 4-Switch Buck-Boost Controller
VIN: 4.7V to 60V, VOUT: 1.2V to 60V, Regulates VOUT, IOUT, IIN, TSSOP-38
LT8705
80V VIN and VOUT Synchronous 4-Switch Buck-Boost VIN: 2.8V to 80V, VOUT: 1.3V to 80V, Regulates VOUT, IOUT, VIN, IIN,
DC/DC Controller
5mm × 7mm QFN-38 and Modified TSSOP-38 for High Voltage
LTC®3789
High Efficiency Synchronous 4-Switch Buck-Boost
Controller
VIN: 4V to 38V, VOUT: 0.8V to 38V, Regulates VOUT, IOUT or IIN, 5mm × 5mm
QFN-32 and SSOP-24
LTC3780
High Efficiency Synchronous 4-Switch Buck-Boost
Controller
VIN: 4V to 36V, VOUT: 0.8V to 30V, Regulates VOUT, 4mm × 5mm QFN-28 and
SSOP-28
LT3763
60V High Current Step-Down LED Driver Controller
VIN: 6V to 60V, 4mm × 4mm QFN-20 and TSSOP-20
LT3757/LT3757A
Boost, Flyback, SEPIC and Inverting Controller
VIN: 2.9V to 40V, Positive or Negative VOUT, 3mm × 3mm DFN-10, MSOP-10
LT3758
High Input Voltage, Boost, Flyback, SEPIC and
Inverting Controller
VIN: 5.5V to 100V, Positive or Negative VOUT, 3mm × 3mm DFN-10, MSOP-10
LT8710
Synchronous SEPIC/Inverting/Boost Controller with
Output Current Control
VIN: 4.5V to 80V, Rail-to-Rail Output Current Monitor and Control, TSSOP-28
32
Rev. B
06/21
www.analog.com
For more information www.analog.com
ANALOG DEVICES, INC. 2017-2021