LTC1264CSW#TRPBF

LTC1264 High Speed, Quad Universal Filter Building Block U FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTIO High Speed, Up to 250kHz Center Frequency Four Identical Filters in a 0.3" Wide Package Clock-to-Center Frequency Ratio of 20:1 Double-Sampling, Improved Aliasing Operates from ±2.37V to ±8V Power Supplies Customized Version with Internal Resistors Available Low Noise Low Harmonic Distortion Available in 24-Pin DIP and SO Wide Packages U APPLICATIO S ■ ■ ■ ■ ■ The LTC ®1264 consists of four identical, high speed 2nd order switched-capacitor filter building blocks designed for center frequencies up to 250kHz. Each building block, together with three to five resistors, can provide 2nd order functions like lowpass, highpass, bandpass and notch. The center frequency of each 2nd order section is tuned via an external clock. The clock-to-center frequency ratio is internally set to 20:1, but it can be modified via external resistors. The aliasing performance of the LTC1264 is improved by double-sampling each 2nd order section. Input signal frequencies can reach up to twice the clock frequency before any alias products will be detectable. Digital Communications Spread Spectrum Communications Spectral Analysis Loran Receivers Instrumentation For Q ≤ 5 and for TA < 85°C, the maximum center frequency is 160kHz. For Q ≤ 2, the maximum center frequency is 250kHz. Up to 8th order filters can be realized by cascading all four 2nd order sections. , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. A customized monolithic version of the LTC1264 including internal thin film resistors can be obtained. U TYPICAL APPLICATIO Clock-Tunable 8th Order Bandpass Filter, fCENTER = fCLK /20 50k Gain vs Frequency 100kHz Bandpass, f –3dB Bandwidth = fCENTER/10 50k IN INV B INV C 10k 10k HPB/NB HPC/NC 10 50k 50k BPC 0 LPB LPC –10 SC –20 SB LTC1264 V– AGND V+ 0.1µF GAIN (dB) MAXIMUM POWER fCENTER SUPPLY 160kHz ±7.5V 120kHz ±5V 60kHz Single 5V BPB CLK SA SD LPA LPD 0.1µF fCLK BPA BPD HPA/NA HPD/ND INV A –40 –50 OUT 50k 10k –30 –60 –70 50k –80 10k 10k INV D 100k FREQUENCY (Hz) 1M 1264 TA02 50k 50k 1264 TA01 1264fb 1 LTC1264 U RATI GS U W W W AXI U W (Note 1) U ABSOLUTE PACKAGE/ORDER I FOR ATIO TOP VIEW Total Supply Voltage (V + to V –) .............................. 16V Input Voltage (Note 2) ........... (V + + 0.3V) to (V – – 0.3V) Output Short-Circuit Duration .......................... Indefinite Power Dissipation ............................................. 400mW Burn-In Voltage ...................................................... 16V Operating Temperature Range ............... – 40°C to 85°C Storage Temperature Range ................ – 65°C to 150°C Lead Temperature (Soldering, 10 sec).................. 300°C INV B 1 24 INV C HPB/NB 2 23 HPC/NC BPB 3 22 BPC LPB 4 21 LPC SB 5 20 SC AGND 6 19 V– V+ 7 18 CLK SA 8 17 SD LPA 9 16 LPD BPA 10 15 BPD HPA/NA 11 ORDER PART NUMBER LTC1264CN LTC1264CSW 14 HPD/ND INV A 12 13 INV D N PACKAGE SW PACKAGE 24-LEAD PLASTIC DIP 24-LEAD PLASTIC SO (WIDE) TJMAX = 110°C, θJA = 65°C/W (N) TJMAX = 110°C, θJA = 85°C/W (S) Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C.(Internal Op Amps) TA = 25°C, unless otherwise noted. PARAMETER Operating Supply Range Voltage Swings CONDITIONS MIN ±2.375 VS = ±2.375V, RL = 5k VS = ±5V, RL = 5k ● ±3.2 ±3.1 VS = ±7.5, RL = 5k TYP MAX ±8 UNITS V V V V V mA dB MHz V/µs MAX UNITS kHz kHz kHz ± 0.7 ±0.8 ±0.8 ±1.0 % % % % % % % % % ppm/°C ppm/°C ±1.5 ±3.7 ±6 3 80 7 10 Output Short-Circuit Current (Source/Sink) DC Open-Loop Gain GBW Product Slew Rate (Complete Filter) VS = ±5V, fCLK = 1MHz, all sides mode 1, fO = 50kHz, Q = 5, TA = 25°C, unless otherwise noted. PARAMETER Center Frequency Range, fO (Note 2) Clock-to-Center Frequency Ratio, fCLK /fO Center Frequency Error (Note 4) CONDITIONS VS = ±7.5V, TA < 85°C, Q < 2 VS = ±5V, TA < 85°C, Q < 2 VS = ±2.5V, TA < 85°C, Q < 2 MIN VS = ±7.5V TYP 0.1 - 250 0.1 - 200 0.1 - 100 20:1 ±0.1 ● VS = ±5V ±0.2 ● Clock-to-Center Frequency Ratio, Side-to-Side Matching Q Accuracy VS = ±2.375V VS ≥ ±5V – 1.6 0.4 ● VS = ±5V – 2.7 ● fO Temperature Coefficient Q Temperature Coefficient fCLK < 2MHz fCLK < 2MHz 0.8 1.0 7.0 ±1 5 1264fb 2 LTC1264 ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Complete Filter) VS = ±5V, fCLK = 1MHz, all sides mode 1, fO = 50kHz, Q = 5, unless otherwise noted. PARAMETER DC Offset Voltage (Note 3) CONDITIONS VOS1 (DC Offset of Input Inverter) VOS2 (DC Offset of First Integrator) VOS3 (DC Offset of Second Integrator) VS = ±7.5V (fCLK is a Square Wave) VS = ±5V (fCLK is a Square Wave) VS = ±2.375V (fCLK is a Square Wave) VS = ±7.5V, TA = 25°C VS = ±5V Clock Feedthrough Maximum Clock Frequency Power Supply Current MIN TYP 9 160 120 90 6 14 ● ● ● MAX ±20 ±45 ±45 ● Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: Please refer to Typical Maximum Q vs Clock Frequency graphs. Note 3: Calculations of output DC offsets of one 2nd order section. Also see Block Diagram. VOSN PINS 2, 11, 14, 23 MODE 23 26 UNITS mV mV mV µVRMS µVRMS µVRMS MHz mA mA Note 4: The center frequency fO, error is calculated as: fO(measured) – fO(ideal) • 100 fO (ideal) VOSBP PINS 3, 10, 15, 22 VOSLP PINS 4, 9, 16, 21 1 VOS1[(1Q) + 1 ||HOLP ||] – VOS3 /Q VOS3 VOSN – VOS2 1b VOS1[(1/Q) + 1 + R2/R1] – VOS3 /Q VOS3 ≈(VOSN – VOS2)(1 + R5/R6) 2 [VOS1(1 + R2/R1 + R2/R3 + R2/R4) – VOS3(R2/R3)] • [R4/(R2 + R4)] + VOS2[R2/(R2 + R4)] VOS3 VOSN – VOS2 3 VOS2 VOS3 VOS1[1 + R4/R1 + R4/R2 + R4/R3] – VOS2(R4/R2) – VOS3(R4/R3) U W TYPICAL PERFOR A CE CHARACTERISTICS A VS = ±7.5V TA ≤ 85°C A. MODES 1, 1b B. MODES 3, 3a B 1.5 2.0 2.5 3.0 3.5 4.0 4.5 CLOCK FREQUENCY (MHz) 5.0 1264 G01 26 24 22 20 18 16 14 12 10 8 6 4 2 0 A Typical Maximum Q vs Clock Frequency 20 VS = ±5V TA ≤ 85°C A 18 VS = SINGLE 5V TA ≤ 85°C 16 A. MODES 1, 1b B. MODES 3, 3a TYPICAL MAXIMUM Q 26 24 22 20 18 16 14 12 10 8 6 4 2 0 Typical Maximum Q vs Clock Frequency TYPICAL MAXIMUM Q TYPICAL MAXIMUM Q Typical Maximum Q vs Clock Frequency B A. MODES 1, 1b B. MODES 3, 3a 14 12 10 B 8 6 4 2 1.0 1.5 3.0 2.5 2.0 3.5 CLOCK FREQUENCY (MHz) 4.0 0 1.0 1.2 1.6 1.8 1.4 CLOCK FREQUENCY (MHz) 2.0 1264 G02 1264 G03 1264fb 3 LTC1264 U W TYPICAL PERFOR A CE CHARACTERISTICS Typical Bandpass Gain Error vs Clock Frequency VS = ±5V 2 VS = ±7.5V 1 2.4 3.2 3.6 2.8 CLOCK FREQUENCY (MHz) 4 MODE 1 Q=4 TA = 25°C VS = ±5V 3 2 VS = ±7.5V 1 0 2.0 4.0 TYPICAL BNADPASS GAIN ERROR (dB) 3 0 2.0 5 5 MODE 1 Q=2 TA = 25°C TYPICAL BANDPASS GAIN ERROR (dB) TYPICAL BANDPASS GAIN ERROR (dB) 5 4 Typical Bandpass Gain Error vs Clock Frequency Typical Bandpass Gain Error vs Clock Frequency 2.4 3.2 3.6 2.8 CLOCK FREQUENCY (MHz) 1264 G04 3 Q=4 2 Q=2 1 0 1.3 4.0 1.4 1.7 1.8 1.9 1,5 1.6 CLOCK FREQUENCY (MHz) Ratio (fCLK /fO) vs Clock Frequency 5 20.5 VS = ±5V MODE 3 Q=4 TA = 25°C 4 BANDPASS OUT MODE 1 VS = ±7.5V 20.4 20.3 20.2 VS = SINGLE 5V fCLK /fO 3 VS = ±7.5V 2 Q = 10 20.1 Q=4 20.0 19.9 19.8 1 Q=2 19.7 19.6 0 2 1 3 4 19.5 1 CLOCK FREQUENCY (MHz) 2 3 4 CLOCK FREQUENCY (MHz) 1264 G15 1264 G11 Power Supply Current vs Supply Voltage Noise vs R2/R4 Ratio 600 48 MODE 3 VS = ±7.5V Q=2 f R2 fO = CLK 20 R4 400 44 POWER SUPPLY CURRENT (mA) 500 NOISE (µVRMS) 2.0 1264 G06 1264 G05 Typical Bandpass Gain Error vs Clock Frequency TYPICAL BANDPASS GAIN ERROR (dB) 4 MODE 1 VS = SINGLE 5V TA = 25°C 300 200 100 40 36 32 28 24 –55°C 25°C 125°C 20 16 12 8 4 0 0 0.2 0.4 0.6 0.8 RESISTOR RATIO (R2/R4) 1.0 1264 G12 0 0 2 4 6 8 10 12 14 16 18 20 22 24 POWER SUPPLY VOLTAGE (V+ – V –) 1264 G14 1264fb 4 LTC1264 U U U PI FU CTIO S V +, V – (Pins 7, 19): Power Supply Pins. The V + (Pin 7) and the V – (Pin 19) should each be bypassed with a 0.1µF capacitor to an adequate analog ground. The filter’s power supplies should be isolated from other digital or high voltage analog supplies. A low noise linear supply is recommended. Using a switching power supply will lower the signal-to-noise ratio of the filter. The supply during power-up should have a slew rate less than 1V/µs. When V + is applied before V – and V – is allowed to go above ground, a diode should clamp V – to prevent latch-up. Figures 1 and 2 show typical connections for dual and single supply operation. ANALOG GROUND PLANE 1 24 2 23 3 22 AGND (Pin 6): Analog Ground Pin. The filter performance depends on the quality of the analog signal ground. For either dual or single supply operation, an analog ground plane surrounding the package is recommended. The analog ground plane should be connected to any digital ground at a single point. For dual supply operation, Pin 6 should be connected to the analog ground plane. For single supply operation, Pin 6 should be biased at 1/2 supply and should be bypassed to the analog ground plane with at least a 1µF capacitor (Figure 2). For single 5V operation and fCLK greater than 1MHz, pin 6 should be biased at 2V. This minimizes passband gain and phase variations. ANALOG GROUND PLANE 1 24 2 23 3 22 4 21 *5 20* –7.5V 4 7.5V 0.1µF 21 5 20 6 19 7 LTC1264 * V 0.1µF 5k + V +/2 6 + 18 1µF 5k V+ 7 19 LTC1264 18 17 *8 17* 9 16 9 16 10 15 10 15 11 14 11 14 12 13 12 13 8 STAR SYSTEM GROUND DIGITAL GROUND PLANE STAR SYSTEM GROUND 200Ω 200Ω CLOCK SOURCE CLOCK SOURCE * OPTIONAL, 1N4148, 1N5819 DIGITAL GROUND PLANE 1264 F01 * FOR MODE 3, THE S NODE PINS 5, 8, 1264 F02 17, 20 SHOULD BE TIED TO PIN 6 Figure 1. Dual Supply Ground Plane Connections Figure 2. Single Supply Ground Plane Connections 1264fb 5 LTC1264 U U U PI FU CTIO S CLK (Pin 18): Clock Input Pin. Any TTL or CMOS clock source with a square wave output and 50% duty cycle (±10%) is an adequate clock source for the device. The power supply for the clock source should not be the filter’s power supply. The analog ground for the filter should be connected to clock’s ground at a single point only. Table 1 shows the clock’s low and high level threshold values for a dual or single supply operation. Table 1. Clock Source High and Low Threshold Levels POWER SUPPLY Dual Supply = ±7.5V Dual Supply = ±5V Dual Supply = ±2.5V Single Supply = 12V Single Supply = 5V HIGH LEVEL ≥ 2.18V ≥ 1.45V ≥ 0.73V ≥ 7.80V ≥ 1.45V LOW LEVEL ≤ 0.5V ≤ 0.5V ≤ – 2.0V ≤ 6.5V ≤ 0.5V HPB/NB, BPB, LPB, LPA, BPA, HPA, HPD, BPD, LPD, LPC, BPC, HPC/NC (Pins 2, 3, 4, 9, 10, 11, 14, 15, 16, 21, 22, 23): Output Pins. Each 2nd order section of the LTC1264 has three outputs which typically source 3mA and sink 1mA. Driving coaxial cables or resistive loads less than 20k will degrade the total harmonic distortion performance of any filter design. When evaluating the distortion or noise performance of a particular filter design implemented with an LTC1264, the final output of the filter should be buffered with a wideband noninverting high slew rate amplifier (Figure 3). – 5k A pulse generator can be used as a clock source provided the high level on-time is greater than 0.2µs. Sine waves are not recommended for clock input frequencies less than 100kHz, since excessively slow clock rise or fall times generate internal clock jitter (maximum clock rise or fall time ≤ 1µs). The clock signal should be routed from the right side of the IC package and perpendicular to it to avoid coupling to any input or output analog signal path. A 200Ω resistor between clock source and Pin 11 will slow down the rise and fall times of the clock to further reduce charge coupling (Figures 1 and 2). LT1224 + 1264 F03 Figure 3. Wideband Buffer INV B, INV A, INV D, INV C (Pins 1, 12, 13, 24): Inverting Input Pins. These pins are the high impedance inverting inputs of internal op amps and they are susceptible to stray capacitive connections to low impedance signal outputs and power supply lines. SB, SA, SD, SC (Pins 5, 8, 17, 20): Summing Input Pins. The summing pins connections determine the circuit topology (mode) of each 2nd order section. Please refer to Modes of Operation. W U ODES OF OPERATIO For the definition of filter functions please refer to the LTC1060 data sheet. Mode 1 In Mode 1, the ratio of the external clock frequency to the center frequency of each 2nd order section is internally fixed at 20:1. Figure 4 illustrates Mode 1 providing 2nd order notch, lowpass, and bandpass outputs. Mode 1 can be used to make high order Butterworth lowpass filters; it can also be used to make low Q notches and for cascading 2nd order bandpass functions tuned at the same center frequency. Mode 1 is faster than Mode 3. Please refer to the Maximum Frequency of Operation paragraph under Applications Information for a guide to the use of capacitor CC. Mode 1b Mode 1b is derived from Mode 1. In Mode 1b (Figure 5) two additional resistors R5 and R6 are added to alternate the amount of voltage fed back from the lowpass output into the input of the SA (SB, SC or SD) switched-capacitor summer. This allows the filter’s clock-to-center frequency ratio to be adjusted beyond 20:1. Mode 1b maintains the speed advantages of Mode 1 and should be considered an 1264fb 6 LTC1264 W U ODES OF OPERATIO optimum mode for high Q designs with fCLK to fCUTOFF (or fCENTER) ratios greater than 20:1. Please refer to the Maximum Frequency of Operation paragraph under Applications Information for a guide to the use of capacitor CC. CC R3 R2 N VIN R1 – S + Σ LP BP – ∫ + ∫ Please refer to the Maximum Frequency of Operation paragraph under Applications Information for a guide to the use of capacitor CC. Mode 2 is a combination of Mode 1 and Mode 3, shown in Figure 7. With Mode 2, the clock-to-center frequency ratio, fCLK /fO, is always less than 20:1. The advantage of Mode 2 is that it provides less sensitivity to resistor tolerances than does Mode 3. As in Mode 1, Mode 2 has a notch output which depends on the clock frequency, and the notch frequency is therefore less than the center frequency, fO. f fi = CLK ; fO = fi; fn = fO 20 R2 R3 R3 Q= ;H =– ;H =– R1 OBP R1 R2 ON HOLP = HON Figure 4. Mode 1, 2nd Order Filter Providing Notch, Bandpass and Lowpass Outputs Please refer to the Maximum Frequency of Operation paragraph under Applications Information for a guide to the use of capacitor CC. CC R6 In Mode 3, the ratio of the external clock frequency to the center frequency of each 2nd order section can be adjusted above or below 20:1. Figure 6 illustrates Mode 3, the classical state variable configuration, providing highpass, bandpass, and lowpass 2nd order filter functions. Mode 3 is slower than Mode 1. Mode 3 can be used to make high order all-pole bandpass, lowpass, and highpass filters. Mode 2 1264 F04 1/4 LTC1264 AGND Mode 3 R5 CC R3 R4 R2 N VIN R1 S LP BP R3 – + + Σ – ∫ R2 ∫ HP 1264 F05 1/4 LTC1264 VIN NOTE: R5 ≤ 5k AGND √ f R6 fi = CLK ; fO = fi ;f =f 20 (R6 + R5) n O R3 R6 ; H = – R2 ; H Q = R3 =– R1 OBP R1 R2 (R6 + R5) ON R2 R6 + R5 HOLP = – R6 R1 √ R1 ( ) Figure 5. Mode 1b, 2nd Order Filter Providing Notch, Bandpass and Lowpass Outputs – + AGND f fi = CLK ; fO = fi 20 + S Σ – LP BP ∫ ∫ 1264 F06 1/4 LTC1264 1 R3 R2 R2 R3 √ R4 ; Q = 1.005( R2) √ R4 ( 1 – 6.42•R4 ) R3 HOHP = – R2 ; HOBP = – R1 R1 ( 1– 1 R3 6.42•R4 ) ; HOLP = – R4 R1 Figure 6. Mode 3, 2nd Order Section Providing Highpass, Bandpass and Lowpass Outputs 1264fb 7 LTC1264 W U ODES OF OPERATIO CC R4 R3 R2 N VIN R1 – S + + Σ LP BP – ∫ ∫ Please refer to the Maximum Frequency of Operation paragraph under Applications Information for a guide to the use of capacitor CC. 1264 F07 1/4 LTC1264 AGND fi = fCLK ;f =f 20 O i √ 1 + R4 ; f = f R2 n O Mode 2n ( ) √ 1 + R2R4 1 – 1R3 ( 6.42•R4 ) R3 Q = 1.005 R2 HOHP = – R2 (AC GAIN, f > fn); HOHPn = – R2 R1 R1 HOBP = – R3 R1 ( 1– 1 R3 6.42•R4 ) tors RH and RL to create a notch. This is shown in Figure 8. Mode 3a is more versatile than Mode 2 because the notch frequency can be higher or lower than the center frequency of the 2nd order section. The external op amp of Figure 8 is not always required. When cascading the sections of the LTC1264, the highpass and lowpass outputs can be summed directly into the inverting input of the next section. ( 1 1 + R2 R4 ) (DC GAIN, f < fn) ; HOLP = HOHPn Figure 7. Mode 2, 2nd Order Filter Providing Highpass Notch, Bandpass and Lowpass Outputs Mode 3a This is an extension of Mode 3 where the highpass and lowpass output are summed through two external resis- This mode extends the circuit topology of Mode 3a to Mode 2 (Figure 9) where the highpass notch and lowpass outputs are summed through two external resistors RH and RL to create a lowpass output with a notch higher in frequency than the notch in Mode 2. This mode, shown in Figure 8, is most useful in lowpass elliptic designs. When cascading the sections of the LTC1264, the highpass notch and lowpass outputs can be summed directly into the inverting input of the next section. Please refer to the Maximum Frequency of Operation paragraph under Applications Information for a guide to the use of capacitor CC. CC R3 R2 HP VIN R1 – + S Σ – + LP BP OHPn ∫ RG ∫ RL 1/4 LTC1264 AGND R √ R f = f √ R4 1 R2 Q = 1.005 ( R3) R2 √ R4 R3 1 – ( 6.42•R4 ) R R H (f = ∞) = ( )( R2 ) ; H (f = 0) = ( )( R4 ) R R1 R R1 f fi = CLK ; fn = fi 20 R4 – RH + H R2 ; O i L G H OLPn G L HIGHPASS OR LOWPASS NOTCH OUTPUT EXTERNAL OP AMP OR INPUT OP AMP OF THE LTC1264, SIDES A, B, C, D 1264 G08 Figure 8. Mode 3a, 2nd Order Filter Providing a Highpass Notch or Lowpass Notch Output 1264fb 8 LTC1264 W U ODES OF OPERATIO CC √ R3 R2 HP VIN R1 √ f fi = CLK ; fn = fi 1 + RH 20 RL R2 fO = fi 1+ R4 R R HOLPn (f = 0)= G + G R2 RH RL R1 R4 – + + S Σ – LP BP ∫ RG ∫ RL ( R3R2) √ 1 + R2R4 Q = 1.005 – + 1/4 LTC1264 )( ) ( ( 1– 1 1 + R2 R4 ) 1 R3 6.42•R4 ) LOWPASS NOTCH OUTPUT RH AGND ( EXTERNAL OP AMP OR INPUT OP AMP OF THE LTC1264, SIDES A, B, C, D 1264 G09 Figure 9. Mode 2n, 2nd Order Filter Providing a Lowpass Notch Output W BLOCK DIAGRA INV A 12 AGND 6 HPA/NA BPA LPA 11 10 9 – + + +∫ 8 SA – + + Σ 5 SB + + – + 19 V– Σ LPC +∫ 21 +∫ – 20 SC HPD/ND 14 INV D 13 CLK +∫ BPC 22 23 – 18 LPB 4 BPB 3 +∫ V+ – HPC/NC INV C 24 +∫ – HPB/NB 2 INV B 1 Σ 7 + Σ LPD BPD 15 +∫ 16 +∫ – 17 SD 1264 BD 1264fb 9 LTC1264 U W U UO APPLICATI S I FOR ATIO Operating Limits The Typical Maximum Q vs Clock Frequency and Bandpass Gain Error graphs, under Typical Performance Characteristics, define an upper limit of operating Q for each LTC1264 2nd order section. These graphs indicate the power supply, fCLK and Q value conditions under which a filter implemented with an LTC1264 will remain stable when operated at temperatures of 85°C or less. For a 2nd order section, a bandpass gain error of 3dB or less is arbitrarily defined as a condition for stability. When the passband gain error begins to exceed 1dB, the use of capacitor CC will reduce the gain error (capacitor CC is connected from the lowpass node to the inverting node of a 2nd order section). Please refer to Figures 4 through 9. The value of CC can be best determined experimentally, and as a guide it should be about 5pF for each 1dB of gain error and not to exceed 15pF. When operating LTC1264 very near the limits defined by the Typical Performance Characteristics graphs, passband gain variations of 2dB or more should be expected. Speed Limitations To avoid op amp slew rate limiting, the signal amplitude should be kept below a specified level as shown in Table 2. Table 2. Maximum VIN vs VS and Clock VS ±7.5V ±5V Single 5V MAXIMUM CLOCK 4MHz to 5MHz 3MHz to 4MHz 1MHz to 2MHz MAXIMUM VIN 0.5VRMS fIN ≥ 400kHz 0.5VRMS fIN ≥ 250kHz 0.35VRMS fIN ≥ 160kHz feedthrough specifications. Switching transients have frequency contents much higher than the applied clock; their amplitude strongly depends on scope probing techniques as well as grounding and power supply bypassing. The clock feedthrough, if bothersome, can be greatly reduced by adding a simple RC lowpass network at the final filter output. This RC will completely eliminate any switching transients. Wideband Noise The wideband noise of the filter is the total RMS value of the device’s noise spectral density and it is used to determine the operating signal-to-noise ratio. Most of its frequency contents lie within the filter passband and it cannot be reduced with post filtering. The total wideband noise (µVRMS) is nearly independent of the value of the clock. The clock feedthrough specifications are not part of the wideband noise. For a specific filter design, the total noise depends on the Q of each section and the cascade sequence. Table 3 shows typical 2nd order section noise (gain = 1) for Q values and supplies operating at 25°C. Noise increases by 20% at the highest operating temperatures. Table 3. 2nd Order Section Noise (µVRMS) for Modes 1, 1b, 2 or 3 (R2 = R4) Q 1 2 3 4 5 VS = ±2.5V 40µVRMS 50µVRMS 60µVRMS 75µVRMS 90µVRMS VS = ±5V 50 60 75 90 110 VS = ±7.5V 60 75 95 115 135 Clock Feedthrough Clock feedthrough is defined as the RMS value of the clock frequency and its harmonics that are present at the filter’s output pins. The clock feedthrough is tested with the filter’s input grounded and it depends on PC board layout and on the value of the power supplies. With proper layout techniques, the typical values of clock feedthrough are listed under Electrical Characteristics. Any parasitic switching transients during the rise and fall edges of the incoming clock are not part of the clock Aliasing Aliasing is an inherent phenomenon of switched-capacitor filters and it occurs when the frequency of input signals approaches the sampling frequency. The input signals that produce the strongest aliased components have a frequency, fIN, such as (fSAMPLING – fIN) falls into the filter’s passband. For the LTC1264 the sampling frequency is twice fCLK. If the input signal spectrum is not band-limited, aliasing may occur. 1264fb 10 LTC1264 U W U UO APPLICATI S I FOR ATIO For example, for an LTC1264 bandpass filter with fCENTER = 100kHz and fCLK = 2MHz, a 3.9MHz, 10mV input will produce a 100kHz, 10mV output. A 1st or 2nd order prefilter will reduce aliasing to acceptable levels in most cases. Table 4. Bandpass Design Specifications (fCENTER is center frequency of passband.) A GUIDE TO BANDPASS DESIGN Note: Reducing passband ripple or attenuation will decrease Q values. The filter order may also increase. Filter design tools like FCAD require design specification inputs such as passband ripple, attenuation, passband width and stopband width in order to calculate filter parameters fO, Q, fn or poles and zeroes. The results of these filter approximations most often require Q values which make excessive demands on the gain-bandwidth products of active filter realizations. The active filter designer should define a gain response so that the filter’s mathematical approximation has practical requirements. Table 4 is a guide to practical design specifications for realizing bandpass filters with LTC1264 (please also refer to the Typical Maximum Q vs Clock Frequency and Bandpass Gain Error graphs under Typical Performance Characteristics). PASSBAND RIPPLE (dB) ≤ 3dB for Butterworth ≤ 0.1 for Chebyshev PASSBAND WIDTH (Hz) ≥ fCENTER /20 ≥ fCENTER /20 STOPBAND ATTENUWIDTH ATION (Hz) (dB) ≥ 5 × Passband –40 to –60 ≥ 5 × Passband –40 to –60 Table 5. Calculated Filter Parameters STAGE fO 1 2 3 4 38.1201kHz 41.9726kHz 35.6418kHz 44.8911kHz Q 4.3346 4.3346 10.5221 10.5221 Table 6. Calculated Mode 1b Resistors to Nearest 1% Value Using Table 5 Filter Parameters and Figure 10 Equations STAGE 1 2 3 4 R1 52.3k 47.5k 56.2k 44.2k R2 10k 10k 10k 10k R3 56.2k 51.1k 147k 118k R5 5k 5k 5k 5k R6 6.98k 11.8k 5.11k 20.5k A Bandpass Design Example Filter Type: Filter Response: Passband Ripple: Attenuation: Center Frequency: Passband Width: Stopband Width: Bandpass Butterworth 3dB 60dB 40kHz (fCENTER) 10kHz 60kHz R2 = 10k R5 = 5k f fi = CLK 20 R1 = R3 (FOR BANDPASS) HOBP 2 R6 = HOBP = Implementing the Bandpass Design R3 = With the LTC1264 in Mode 1b, Butterworth and Chebyshev bandpass designs with fCLK to fCENTER ratios greater than 20:1 are possible. R5•fO ( fi 2 √ 2 – fO Q 2 ( ) fO fCENTER ) ( – fCENTER fO ) 2 +1 R2•Q √( R6 R6 + 5 ) 1264 F10 Figure 10. Equations for Resistors in Mode 1b Operation First choose the clock frequency which in Mode 1b must be greater than 20 times the bandpass center frequency of 40kHz. For this example, let’s choose fCLK to be 1MHz. Table 6 lists the resistors for for the bandpass design example and Figure 11 shows the complete circuit. 1264fb 11 LTC1264 W U U UO APPLICATI S I FOR ATIO R1 R1 INV B INV C R2 R2 HPB/NB HPC/NC R3 R3 STAGE 1 R5 R6 R6 R5 STAGE 3 R3 BPB BPC LPB LPC R5 SB LTC1264 SC V– AGND V+ CLK SA SD LPA LPD BPA BPD HPA/NA fCLK R6 R6 1.0 0.5 0 R5 –0.5 STAGE 4 R3 HPD/ND R2 R2 INV A R1 STAGE 2 INV D R1 GAIN (dB) IN first stage and decreasing the R1 resistor of the last stage by the same amount (multiplying the R1 resistor of the first stage and dividing the R1 resistor of the last stage by 2 for narrowband filter, and by 5 for wideband filter is a good rule of thumb). This adjustment may, however, increase the filter’s passband noise. OUT MODE 1b VS = ±7.5V fCLK = 1MHz fCLK /fCENTER = 25:1 –1.0 –1.5 –2.0 –2.5 –3.0 1264 F11 –3.5 –4.0 Figure 11. Mode 1b Bandpass Filter 30 32 34 36 38 40 42 44 46 48 50 FREQUENCY (kHz) 1264 F12 The sequence of 2nd order stages and the bandpass gain HOBP of each stage will determine the gain peaks at the filter’s intermediate outputs. A given internal output can have several dB more gain than the final filter output. Gain peaks occur around the corners of the passband. The gain peaks can be reduced by increasing the R1 resistor of the Figure 12. Passband Gain vs Frequency 40kHz Butterworth Bandpass 10 0 –10 –20 GAIN (dB) Figures 12 and 13 show the gain response graphs of the 40kHz Butterworth bandpass design described above. The passband gain response graph (Figure 12) shows a 40kHz gain of – 0.4dB and a tilted passband from 37kHz to 43kHz. These errors are due to the 1% resistors used and the sideto-side matching of the LTC1264 fCLK-to-fCENTER ratio which typically is 0.4%. To adjust for 0dB gain at 40kHz, reduce the value of R1 in the first stage by 5%. To adjust for a flat passband, adjust by ±1% the value of R6 in stages 3 and 4. Adjusting R6 compensates for the side-to-side matching errors. Please refer to Figure 5 equations defining fO and Q as a function of R6. MODE 1b VS = ±7.5V fCLK = 1MHz fCLK /fCENTER = 25:1 –30 –40 –50 –60 –70 –80 –90 10 18 26 34 42 50 58 66 74 82 90 FREQUENCY (kHz) 1264 F13 Figure 13. Gain vs Frequency 40kHz Butterworth Bandpass 1264fb 12 LTC1264 UO TYPICAL APPLICATI S Gain vs Frequency Linear Phase Clock-Tunable to 400kHz, Dual 4th Order Lowpass Filter R1 0 R1 OUT 1 IN 1 INV B –10 INV C R2 R2 HPB/NB HPC/NC R3 –20 R3 BPB BPC LPB LPC R4 GAIN (dB) R4 C C SB 0.1µF SC LTC1264 V– AGND V+ 8V C SD LPA LPD C –70 –80 10k R4 R3 100k FREQUENCY (Hz) BPD R3 R2 HPA/NA R2 INV A IN 2 INV D OUT 2 R1 C B 2 2 17.8k 20k 27.4k 27.4k 19.6k 21k 51.1k 75k 5pF 5pF A 2 17.8k 27.4k 19.6k 51.1k 5pF D 2 20k 27.4k 21k 75k 5pF f –3dB (VS = ±8V) 125kHz 200kHz 275kHz 400kHz fCLK 2MHz 3MHz 4MHz 5MHz TA ≤ 50°C 1264 TA04a Clock-Tunable, fCENTER = fCLK /20, 100kHz, 4th Order Bandpass and Notch Filters Gain vs Frequency R1 10 R1 BANDPASS IN INV B 0 INV C R2 R2 HPB/NB R3 BPB BPC LPB LPC SB BANDPASS OUT SC LTC1264 V– AGND 7.5V –20 V+ CLK SA SD LPA LPD – 7.5V 0.1µF fCLK 2MHz NOTCH OUT BPD R2 R2 C –40 –50 –60 R3 HPA/NA –30 –70 R3 BPA GAIN (dB) 0.1µF R1 –10 HPC/NC R3 NOTCH IN 1M 1264 TA04b HPD/ND R1 LTC1264 SIDE MODE R1 R2 R3 R4 C –50 –60 0.1µF fCLK R4 BPA –40 –8V CLK SA –30 VS = ±7.5V fCLK = 2MHz –80 10k 100k FREQUENCY (Hz) 1M 1264 TA05b HPD/ND INV A C INV D R1 LTC1264 SIDE MODE R1 R2 R3 C B 1 20k 10k 20k C 1 20k 10k 20k A 1 10k 10k 20k 10pF D 1 10k 10k 20k 10pF 1264 TA05a 1264fb 13 LTC1264 UO TYPICAL APPLICATI S 100kHz, 8th Order Notch Filter, fCLK /fCENTER = 20:1 Gain vs Frequency R1 10 0 C R1 INV B INV C R2 R2 HPB/NB HPC/NC R3 0.1µF –20 R3 BPB BPC LPB LPC SB SC LTC1264 V+ CLK SA SD LPA LPD –30 –40 –50 V– AGND 7.5V –10 GAIN (dB) IN –7.5V R3 –60 0.1µF fCLK 2MHz VS = ±7.5V fCLK = 2MHz –70 –80 10k OUT R3 BPA 100k FREQUENCY (Hz) 1M 1264 TA06b BPD R2 R2 HPA/NA LTC1264 SIDE MODE R1 R2 R3 C HPD/ND INV A INV D C R1 R1 C B 1 1 36.5k 3.92k 10k 10k 50k 27.4k 30pF D 1 9.09k 10k 50k 30pF A 1 7.5k 10k 50k 1264 TA06a Clock-Tunable, 8th Order Elliptic Lowpass Filter, fCLK /fCUTOFF = 20:1 Gain vs Frequency RL 0 RH INV B INV C R2 –20 R2 HPB/NB HPC/NC R3 R3 BPB BPC LPB LPC GAIN (dB) IN R4 R4 C 0.1µF SB LTC1264 7.5V C V+ –30 –40 –50 SC V– AGND VS = ±7.5V fCLK = 2MHz –10 R1 –70 CLK SA SD LPA LPD BPA BPD –60 –7.5V 0.1µF RL RH –80 10k fCLK 2MHz R4 R4 R3 100k FREQUENCY (Hz) 1M 1264 TA03b R3 R2 HPA/NA HPD/ND R2 INV A INV D OUT RH RL 1264 TA03a POWER SUPPLY ±7.5V ±5V SINGLE 5V MAXIMUM fCLK 3.6MHz (C = 10pF) 2.0MHz (C = 10pF) 1.6MHz (C = 10pF) LTC1264 SIDE MODE R1 R2 R3 R4 RH RL C C B 2n 3a 27.4k 23.7k 20k 20k 37.4k 28k 100k 137k 100k 27.4k 31.6k 3pF A 2n D 3 20k 37.4k 100k 130k 24.3k 3pF 29.4k 19.1k 48.7k 1264fb 14 LTC1264 U PACKAGE DESCRIPTIO N Package 24-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) 1.280* (32.512) MAX 24 23 22 21 20 19 18 17 16 15 14 13 1 2 3 4 5 6 7 8 9 10 11 12 .255 ± .015* (6.477 ± 0.381) .300 – .325 (7.620 – 8.255) .130 ± .005 (3.302 ± 0.127) .045 – .065 (1.143 – 1.651) .020 (0.508) MIN .008 – .015 (0.203 – 0.381) ( +.035 .325 –.015 8.255 +0.889 –0.381 .065 (1.651) TYP N24 0405 .120 (3.048) MIN ) .018 ± .003 (0.457 ± 0.076) .100 (2.54) BSC NOTE: 1. DIMENSIONS ARE INCHES MILLIMETERS *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) SW Package 24-Lead Plastic Small Outline (Wide .300 Inch) (Reference LTC DWG # 05-08-1620) .050 BSC .045 ±.005 .030 ±.005 TYP N 24 23 22 21 .598 – .614 (15.190 – 15.600) NOTE 4 20 19 18 17 16 15 14 13 N .325 ±.005 .420 MIN .394 – .419 (10.007 – 10.643) NOTE 3 1 2 3 N/2 N/2 RECOMMENDED SOLDER PAD LAYOUT .005 (0.127) RAD MIN .009 – .013 (0.229 – 0.330) .291 – .299 (7.391 – 7.595) NOTE 4 .010 – .029 × 45° (0.254 – 0.737) 2 3 4 5 6 7 8 9 10 11 .093 – .104 (2.362 – 2.642) 12 .037 – .045 (0.940 – 1.143) 0° – 8° TYP NOTE 3 .016 – .050 (0.406 – 1.270) NOTE: 1. DIMENSIONS IN 1 .050 (1.270) BSC .004 – .012 (0.102 – 0.305) .014 – .019 (0.356 – 0.482) TYP INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS 4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) S24 (WIDE) 0502 1264fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC1264 UO TYPICAL APPLICATI 8th Order Bandpass Filter, Linear Phase RH RL R1 VIN INV B LTC1264 SIDE MODE R1 R2 R3 R4 RH RL INV C R2 R2 HPB/NB HPC/NC R3 R3 BPB BPC R4 R4 LPB LPC C 0.1µF SB SC LTC1264 V– AGND 7.5V V+ CLK SA SD LPA LPD BPA BPD 1MHz –7.5V 0.1µF fCLK 1MHz 1.5MHz 2.0MHz R4 R4 C B 3 3a 97.6k 10.7k 12.4k 39.2k 39.2k 13.3k 10.7k 53.6 15.0k D 3 10.0k 29.4k 10.0k 27.4k 100.0k C 0pF 5pF 10pF R3 R3 A 3a 32.4k 10.7k 12.4k 11.5k 1264 TA07a R2 R2 HPA/NA HPD/ND INV A INV D VOUT RH R1 RL 50kHz Bandpass Filter, Linear Phase Gain vs Frequency Passband Gain and Group Delay 10 3 VS = ±7.5V fCLK = 1MHz 0 124 114 GAIN –10 –3 104 –20 –6 94 GAIN (dB) –30 –40 –9 84 DELAY –12 74 –15 64 –60 –18 54 –70 –21 44 –80 –24 34 –90 10k –27 –50 100k FREQUENCY (Hz) 1M 1264 TA07b 40 42 44 46 48 50 52 54 56 58 60 FREQUENCY (kHz) GROUP DELAY (µs) GAIN (dB) 0 24 1264 TA07c RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1068 Very Low Noise, High Accuracy, Quad Universal Filter Building Block Four 2nd Order Filter Sections in 28-Pin SSOP, 56kHz Max Center Frequency, ≤40µVRMS Noise per 2nd Order Section, Operation 3.3V to ±5V LTC1068-25 High Speed, High Accuracy, Quad Universal Filter Building Block Four 2nd Order Filter Sections in 28-Pin SSOP, 200kHz Max Center Frequency, Operation 3.3V to ±5V LTC1068-50 Low Power, High Accuracy, Quad Universal Filter Building Block Four 2nd Order Filter Sections in 28-Pin SSOP, 40kHz Max Center Frequency, 3.5mA at Single 5V, Operation 3.3V to ±5V LTC1562 Very Low Noise, Low Distortion, Active RC Quad Universal Filter Four 2nd Order Filter Sections, No Clock Required, 150kHz Max Center Frequency, SSOP 1264fb 16 Linear Technology Corporation LT/LT 0805 REV B • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 1993