LTC2435/LTC2435-1
20-Bit No Latency ∆∑™
ADCs with Differential Input and
Differential Reference
Description
Features
2× Speed Up Version of the LTC2430: 15Hz Output
Rate, 60Hz Notch—LTC2435; 13.75Hz Output Rate,
Simultaneous 50Hz/60Hz Notch—LTC2435-1
n Differential Input and Differential Reference with
GND to VCC Common Mode Range
n 3ppm INL, No Missing Codes
n 10ppm Gain Error
n 0.8ppm Noise
n Single Conversion Settling Time for Multiplexed
Applications
n Internal Oscillator—No External Components Required
n Single Supply 2.7V to 5.5V Operation
n Low Supply Current (200µA,4µA in Auto Sleep)
n 20-Bit ADC in Narrow SSOP-16 Package
(SO-8 Footprint)
n
Applications
Direct Sensor Digitizer
Weight Scales
n Direct Temperature Measurement
n Gas Analyzers
n Strain Gage Transducers
n Instrumentation
n Data Acquisition
n Industrial Process Control
n 6-Digit DVMs
n
n
The LTC®2435/LTC2435-1 are 2.7V to 5.5V micropower
20‑bit differential ∆∑ analog to digital converters with
integrated oscillator, 3ppm INL and 0.8ppm RMS noise.
They use delta-sigma technology and provide single
cycle settling time for multiplexed applications. Through
a single pin, the LTC2435 can be configured for better
than 110dB input differential mode rejection at 50Hz or
60Hz ± 2%, or it can be driven by an external oscillator
for a user defined rejection frequency. The LTC2435-1
can be configured for better than 87dB input differential
mode rejection over the range of 49Hz to 61.2Hz (50Hz
and 60Hz ±2% simultaneously). The internal oscillator
requires no external frequency setting components.
The converters accept any external differential reference
voltage from 0.1V to VCC for flexible ratiometric and remote sensing measurement configurations. The full-scale
differential input range is from –0.5VREF to 0.5VREF . The
reference common mode voltage, VREFCM, and the input
common mode voltage, VINCM, may be independently set
anywhere within the GND to VCC range of the LTC2435/
LTC2435-1. The DC common mode input rejection is
better than 120dB.
The LTC2435/LTC2435-1 communicate through a flexible
3-wire digital interface which is compatible with SPI and
MICROWIRE™ protocols.
L, LT, LTC and LTM are registered trademarks and C-Load and No Latency ∆∑ are trademarks
of Linear Technology Corporation. Protected by U.S. Patents including 6140950, 6169506.
Typical Applications
Integral Nonlinearity vs Input
10
2.7V TO 5.5V
8
VCC
2
VCC
FO
14
LTC2435/
LTC2435-1
REFERENCE
VOLTAGE
0.1V TO VCC
3
ANALOG INPUT RANGE
–0.5VREF TO 0.5VREF
5
4
6
1, 7, 8, 9, 10, 15, 16
+
REF
SCK
13
REF–
IN+
SDO
IN–
CS
GND
= INTERNAL OSC/50Hz REJECTION (LTC2435)
= EXTERNAL CLOCK SOURCE
= INTERNAL OSC/60Hz REJECTION (LTC2435)
= INTERNAL 50Hz/60Hz REJECTION (LTC2435-1)
12
3-WIRE
SPI INTERFACE
6
INL (ppm OF VREF)
1μF
4
–2
–4
–8
2435 TA01
TA = 85°C
0
–6
11
TA = 25°C
2
TA = –45°C
FO = GND
VCC = 5V
VREF = 5V
VINCM = VINCM = 2.5V
–10
–2.5
–1.5
–0.5
0.5
1.5
INPUT VOLTAGE (V)
2.5
2435 TA01b
24351fc
For more information www.linear.com/LTC2435
1
LTC2435/LTC2435-1
Absolute Maximum Ratings
Pin Configuration
(Notes 1, 2)
TOP VIEW
Supply Voltage (VCC) to GND........................– 0.3V to 7V
Analog Input Pins Voltage to GND.–0.3V to (VCC + 0.3V)
Reference Input Pins Voltage
to GND...........................................–0.3V to (VCC + 0.3V)
Digital Input Voltage to GND..........–0.3V to (VCC + 0.3V)
Digital Output Voltage to GND........–0.3V to (VCC + 0.3V)
Operating Temperature Range
LTC2435C/LTC2435-1C ............................ 0°C to 70°C
LTC2435I/LTC2435-1I .......................... –40°C to 85°C
Storage Temperature Range.................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)................... 300°C
GND
1
16 GND
VCC
2
15 GND
REF+
3
14 FO
REF–
4
13 SCK
IN+
5
12 SDO
IN–
6
11 CS
GND
7
10 GND
GND
8
9
GND
GN PACKAGE
16-LEAD PLASTIC SSOP
TJMAX = 125°C, θJA = 95°C/W
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2435CGN#PBF
LTC2435CGN#TRPBF
2435
16-Lead Plastic SSOP
0°C to 70°C
LTC2435IGN#PBF
LTC2435CGN#TRPBF
2435I
16-Lead Plastic SSOP
–40°C to 85°C
LTC2435-1CGN#PBF
LTC2435-1CGN#TRPBF
24351
16-Lead Plastic SSOP
0°C to 70°C
LTC2435-1IGN#PBF
LTC2435-1IGN#TRPBF
24351I
16-Lead Plastic SSOP
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on nonstandard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
Electrical Characteristics
The l denotes specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
Resolution (No Missing Codes)
0.1V ≤ VREF ≤ VCC, –0.5 • VREF ≤ VIN ≤ 0.5 • VREF , (Note 5)
Integral Nonlinearity
5V ≤ VCC ≤ 5.5V, REF+ = 2.5V, REF– = GND, VINCM = 1.25V, (Note 6)
5V ≤ VCC ≤ 5.5V, REF+ = 5V, REF– = GND, VINCM = 2.5V, (Note 6)
2.7V ≤ VCC ≤ 5.5V, REF+ = 2.5V, REF– = GND, VINCM = 1.25V, (Note 6)
2.5V ≤ REF+ ≤ VCC, REF– = GND,
GND ≤ IN+ = IN– ≤ VCC, (Note 14)
2.5V ≤ REF+ ≤ VCC, REF– = GND,
GND ≤ IN+ = IN– ≤ VCC
2.5V ≤ REF+ ≤ VCC, REF– = GND,
IN+ = 0.75REF+, IN– = 0.25 • REF+
Offset Error
Offset Error Drift
Positive Gain Error
MIN
Positive Gain Error Drift
2.5V ≤ REF+ ≤ VCC, REF– = GND,
IN+ = 0.75REF+, IN– = 0.25 • REF+
Negative Gain Error
2.5V ≤ REF+ ≤ VCC, REF– = GND,
IN+ = 0.25 • REF+, IN– = 0.75 • REF+
Negative Gain Error Drift
2.5V ≤ REF+ ≤ VCC, REF– = GND,
IN+ = 0.25 • REF+, IN– = 0.75 • REF+
Output Noise
5V ≤ VCC ≤ 5.5V, REF+ = 5V, REF – = GND,
GND ≤ IN– = IN+ ≤ VCC, (Note 13)
●
TYP
MAX
20
UNITS
Bits
●
2
3
10
20
ppm of VREF
ppm of VREF
ppm of VREF
●
2
5
mV
100
●
10
nV/°C
25
0.1
●
10
0.1
4
ppm of VREF
ppm of VREF/°C
25
ppm of VREF
ppm of VREF/°C
µVRMS
24351fc
2
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Converter
Characteristics
The l denotes specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
MIN
TYP
Input Common Mode Rejection DC
2.5V ≤ REF+ ≤ VCC, REF– = GND,
GND ≤ IN– = IN+ ≤ VCC (Note 5)
●
110
120
MAX
UNITS
Input Common Mode Rejection
60Hz ± 2% (LTC2435)
2.5V ≤ REF+ ≤ VCC, REF– = GND,
GND ≤ IN – = IN+ ≤ VCC, (Notes 5, 7)
●
140
dB
Input Common Mode Rejection
50Hz ± 2% (LTC2435)
2.5V ≤ REF+ ≤ VCC, REF– = GND,
GND ≤ IN – = IN+ ≤ VCC, (Notes 5, 8)
●
140
dB
Input Normal Mode Rejection
60Hz ± 2% (LTC2435)
(Notes 5, 7)
●
110
120
dB
Input Normal Mode Rejection
50Hz ±2% (LTC2435)
(Notes 5, 8)
●
110
120
dB
Input Common Mode Rejection
49Hz to 61.2Hz (LTC2435-1)
2.5V ≤ REF+ ≤ VCC, REF– = GND,
GND ≤ IN– = IN+ ≤ VCC, (Notes 5, 7)
●
120
dB
Input Normal Mode Rejection
49Hz to 61.2Hz (LTC2435-1)
FO = GND (Note 5)
●
87
dB
Input Normal Mode Rejection
External Clock fEOSC/2560 ±14%
External Oscillator (Note 5)
●
87
dB
Input Normal Mode Rejection
External Clock fEOSC/2560 ±4%
External Oscillator (Note 5)
●
110
120
dB
Reference Common Mode
Rejection DC
2.5V ≤ REF+ ≤ VCC, GND ≤ REF– ≤ 2.5V,
VREF = 2.5V, IN– = IN+ = GND (Note 5)
●
130
140
dB
Power Supply Rejection, DC
REF+ = VCC, REF– = GND, IN– = IN+ = GND
100
dB
Power Supply Rejection, 60Hz ±2%
REF+ = 2.5V, REF– = GND, IN– = IN+ = GND, (Note 7)
120
dB
Power Supply Rejection, 50Hz ±2%
REF+ = 2.5V, REF– = GND, IN– = IN+ = GND, (Note 8)
120
dB
dB
Analog
Input And Reference ● denotes specifications which apply over the full operating
The
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
IN+
Absolute/Common Mode IN+ Voltage
●
GND – 0.3V
VCC + 0.3V
V
IN–
Absolute/Common Mode IN– Voltage
●
GND – 0.3V
VCC + 0.3V
V
VIN
Input Differential Voltage Range
(IN+ – IN–)
●
–VREF/2
VREF/2
V
REF+
Absolute/Common Mode REF+ Voltage
●
0.1
VCC
V
REF–
Absolute/Common Mode REF– Voltage
●
GND
VCC – 0.1V
V
VREF
Reference Differential Voltage Range
(REF+ – REF–)
●
0.1
VCC
V
CS (IN+)
IN+ Sampling Capacitance
1.5
pF
CS
(IN–)
IN– Sampling Capacitance
1.5
pF
CS
(REF+)
REF+ Sampling Capacitance
1.5
pF
CS (REF–)
REF– Sampling Capacitance
1.5
pF
IDC_LEAK
(IN+)
IN+ DC Leakage Current
IDC_LEAK
(IN–)
IN– DC Leakage Current
IDC_LEAK (REF+)
REF+ DC Leakage Current
(REF–)
REF– DC Leakage Current
IDC_LEAK
CONDITIONS
CS = VCC, IN+ = GND
CS = VCC, IN– = VCC
CS = VCC, REF+ = VCC
CS = VCC, REF– = GND
MIN
TYP
MAX
UNITS
●
–10
1
10
nA
●
–10
1
10
nA
●
–10
1
10
nA
●
–10
1
10
nA
24351fc
For more information www.linear.com/LTC2435
3
LTC2435/LTC2435-1
Digital
Inputs And Digital Outputs l denotes specifications which apply over the full
The
operating temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
VIH
High Level Input Voltage
CS, FO
2.7V ≤ VCC ≤ 5.5V
2.7V ≤ VCC ≤ 3.3V
●
VIL
Low Level Input Voltage
CS, FO
4.5V ≤ VCC ≤ 5.5V
2.7V ≤ VCC ≤ 5.5V
●
VIH
High Level Input Voltage
SCK
2.7V ≤ VCC ≤ 5.5V (Note 9)
2.7V ≤ VCC ≤ 3.3V (Note 9)
●
VIL
Low Level Input Voltage
SCK
4.5V ≤ VCC ≤ 5.5V (Note 9)
2.7V ≤ VCC ≤ 5.5V (Note 9)
●
IIN
Digital Input Current
CS, FO
0V ≤ VIN ≤ VCC
●
IIN
Digital Input Current
SCK
0V ≤ VIN ≤ VCC (Note 9)
●
CIN
Digital Input Capacitance
CS, FO
CIN
Digital Input Capacitance
SCK
(Note 9)
VOH
High Level Output Voltage
SDO
IO = –800µA
●
VOL
Low Level Output Voltage
SDO
IO = 1.6mA
●
VOH
High Level Output Voltage
SCK
IO = –800µA (Note 10)
●
VOL
Low Level Output Voltage
SCK
IO = 1.6mA (Note 10)
●
IOZ
Hi-Z Output Leakage
SDO
●
TYP
MAX
UNITS
2.5
2.0
V
V
0.8
0.6
V
V
2.5
2.0
V
V
0.8
0.6
V
V
–10
10
µA
–10
10
µA
10
pF
10
pF
VCC – 0.5
V
0.4
V
VCC – 0.5
V
–10
0.4
V
10
µA
Power
Requirements ● denotes specifications which apply over the full operating temperature range,
The
otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
VCC
Supply Voltage
ICC
Supply Current
Conversion Mode
Sleep Mode
Sleep Mode
CONDITIONS
MIN
●
CS = 0V (Note 12)
CS = VCC (Note 12)
CS = VCC, 2.7V ≤ VCC ≤ 3.3V (Note 12)
●
●
●
TYP
2.7
200
4
2
MAX
UNITS
5.5
V
300
10
µA
µA
µA
24351fc
4
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Timing
Characteristics
The
l denotes specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
fEOSC
External Oscillator Frequency Range
●
tHEO
External Oscillator High Period
●
tLEO
External Oscillator Low Period
tCONV
Conversion Time (LTC2435)
MAX
UNITS
5
2000
kHz
0.25
200
µs
●
0.25
FO = 0V
FO = VCC
External Oscillator (Note 11)
●
●
●
65.6
78.7
Conversion Time (LTC2435-1)
FO = 0V
External Oscillator (Note 11)
●
●
72
fISCK
Internal SCK Frequency
Internal Oscillator (Note 10), LTC2435
Internal Oscillator (Note 10), LTC2435-1
External Oscillator (Notes 10, 11)
DISCK
Internal SCK Duty Cycle
(Note 10)
TYP
200
µs
66.9
80.3
68.3
81.9
ms
ms
ms
73.5
10278/fEOSC (in kHz)
75
ms
ms
10278/fEOSC (in kHz)
19.2
17.5
fEOSC /8
●
45
fESCK
External SCK Frequency Range
(Note 9)
●
tLESCK
External SCK Low Period
(Note 9)
●
tHESCK
External SCK High Period
(Note 9)
●
250
tDOUT_ISCK
Internal SCK 24-Bit Data Output Time
Internal Oscillator (Notes 10, 12), LTC2435
Internal Oscillator (Notes 10, 12), LTC2435-1
External Oscillator (Notes 10, 11)
●
●
●
1.22
1.34
tDOUT_ESCK
External SCK 24-Bit Data Output Time
(Note 9)
●
kHz
kHz
kHz
55
%
2000
kHz
250
ns
ns
1.25
1.37
192/fEOSC (in kHz)
1.28
1.40
24/fESCK (in kHz)
ms
ms
ms
ms
t1
CS ↓ to SDO Low Z
●
0
200
ns
t2
CS ↑ to SDO High Z
●
0
200
ns
t3
CS ↓ to SCK ↓
(Note 10)
●
0
200
ns
t4
CS ↓ to SCK ↑
(Note 9)
●
50
tKQMAX
SCK ↓ to SDO Valid
220
ns
tKQMIN
SDO Hold After SCK ↓
t5
t6
●
ns
●
15
ns
SCK Set-Up Before CS ↓
●
50
ns
SCK Hold After CS ↓
●
(Note 5)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to GND.
Note 3: VCC = 2.7 to 5.5V unless otherwise specified.
VREF = REF + – REF–, VREFCM = (REF+ + REF–)/2;
VIN = IN+ – IN –, VINCM = (IN + + IN –)/2.
Note 4: FO pin tied to GND or to VCC or to external conversion clock
source with fEOSC = 153600Hz unless otherwise specified.
Note 5: Guaranteed by design, not subject to test.
Note 6: Integral nonlinearity is defined as the deviation of a code from
a straight line passing through the actual endpoints of the transfer
curve. The deviation is measured from the center of the quantization
band.
Note 7: FO = 0V (internal oscillator) or fEOSC = 153600Hz ± 2%
(external oscillator) for the LTC2435 or fEOSC = 139800Hz ±2% for the
LTC2435-1.
50
ns
Note 8: FO = VCC (internal oscillator) or fEOSC = 128000Hz ±2%
(external oscillator).
Note 9: The converter is in external SCK mode of operation such that
the SCK pin is used as digital input. The frequency of the clock signal
driving SCK during the data output is fESCK and is expressed in kHz.
Note 10: The converter is in internal SCK mode of operation such that
the SCK pin is used as digital output. In this mode of operation the
SCK pin has a total equivalent load capacitance CLOAD = 20pF.
Note 11: The external oscillator is connected to the FO pin. The external
oscillator frequency, fEOSC, is expressed in kHz.
Note 12: The converter uses the internal oscillator.
FO = 0V or FO = VCC.
Note 13: The output noise includes the contribution of the internal
calibration operations.
Note 14: Refer to Offset Accuracy and Drift in the Applications
Information section.
24351fc
For more information www.linear.com/LTC2435
5
LTC2435/LTC2435-1
Typical Performance Characteristics
–680
FO = GND
VCC = 5V
–685 VREF = 2.5V
VINCM = VINCM = 1.25V
TA = –45°C
–350
–695
TA = 85°C
–700
TA = 85°C
–355
TA = 25°C
Total Unadjusted Error (VCC =
2.7V, VREF = 2.5V)
FO = GND
VCC = 2.7V
VREF = 2.5V
–330 VINCM = VINCM = 1.25V
TA = –45°C
–690
TA = 25°C
–320
TUE (ppm OF VREF)
TUE (ppm OF VREF)
FO = GND
VCC = 5V
VREF = 5V
–345 VINCM = VINCM = 2.5V
Total Unadjusted Error (VCC = 5V,
VREF = 2.5V)
TUE (ppm OF VREF)
–340
Total Unadjusted Error (VCC = 5V,
VREF = 5V)
TA = –45°C
–340
TA = 25°C
TA = 85°C
–350
–705
–360
–2.5
–1.5
0.5
1.5
–0.5
INPUT VOLTAGE (V)
–710
–1.25
2.5
–0.75
Integral Nonlinearity (VCC = 5V,
VREF = 5V)
3
10
8
–2
–8
Integral Nonlinearity (VCC = 5V,
VREF = 2.5V)
TA = –45°C
FO = GND
VCC = 5V
VREF = 5V
VINCM = VINCM = 2.5V
–10
–2.5
–1.5
–0.5
0.5
1.5
INPUT VOLTAGE (V)
2.5
10
FO = GND
8 VCC = 2.7V
VREF = 2.5V
6 V
INCM = VINCM = 1.25V
TA = –45°C
1
0
TA = 85°C
–1
TA = 25°C
FO = GND
–2 VCC = 5V
VREF = 2.5V
VINCM = VINCM = 1.25V
–3
–1.25 –0.75
–0.25
0.25
0.75
INPUT VOLTAGE (V)
4
Noise Histogram (Output Rate =
15Hz, VCC = 5V, VREF = 5V)
14
10,000 CONSECUTIVE READINGS
VCC = 5V
25 VREF = 5V
GAUSSIAN
VIN = 0V
DISTRIBUTION
VINCM = 2.5V
m = –325.4ppm
20 FO = GND
σ = 0.79ppm
TA = 25°C
15
10
NUMBER OF READINGS (%)
30
TA = 25°C
TA = –45°C
2
0
–2
TA = 85°C
–4
–6
–8
1.25
–10
–1.25
–0.75
–0.25
0.25
0.75
INPUT VOLTAGE (V)
2435 G05
2435 G04
NUMBER OF READINGS (%)
1.25
Integral Nonlinearity (VCC = 2.7V,
VREF = 2.5V)
INL (ppm of VREF)
TA = 85°C
0
–6
INL (ppm OF VREF)
INL (ppm OF VREF)
TA = 25°C
2
–0.25
0.25
0.75
INPUT VOLTAGE (V)
2435 G03
2
6
4
–0.75
2435 G02
2435 G01
–4
–360
–1.25
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
1.25
2435 G06
Noise Histogram (Output Rate =
15Hz, VCC = 2.7V, VREF = 2.5V)
10,000 CONSECUTIVE READINGS
VCC = 2.7V
GAUSSIAN
12 V
DISTRIBUTION
REF = 2.5V
VIN = 0V
m = –365ppm
10 VINCM = 2.5V
σ = 1.55ppm
FO = GND
8 TA = 25°C
6
4
5
2
0
–330 –329 –328 –327 –326 –325 –324 –323 –322 –321
OUTPUT CODE(ppm OF VREF)
0
–372 –370 –368 –366 –364 –362 –360 –358
OUTPUT CODE (ppm OF VREF)
2435 G07
2435 G08
24351fc
6
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Typical Performance Characteristics
RMS Noise vs Input Differential
Voltage
5.0
RMS NOISE (μV)
RMS NOISE (ppm OF VREF)
VCC = 5V
1.4 VREF = 5V
VINCM = 2.5V
1.3 F = GND
O
1.2 TA = 25°C
1.1
1.0
0.9
0.8
RMS Noise vs VINCM
5.0
FO = GND
4.8 REF+ = 5V
REF– = GND
4.6 T = 25°C
A
4.4 VCC = 5V
VIN = 0V
4.2 VINCM = GND
RMS NOISE (μV)
1.5
4.0
3.8
3.6
4.2
4.0
3.8
3.6
0.7
3.4
0.6
3.2
3.2
0.5
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5 2
INPUT DIFFERENTIAL VOLTAGE (V)
3.0
–1
1
0
3
2
VINCM (V)
4
5.0
4.0
3.8
3.6
3.5
3.9 4.3
VCC (V)
4.7
5.1
3.0
5.5
–326
–328
–330
–332
0
4
3
2
VREF (V)
1
2435 G13
–326
–328
–330
–320
–322
Offset Error vs VCC = VREF
–1.60
REF+ = VCC
REF– = GND
–334
–336
–1.65
–1.66
–1.68
–1.69
–340
–45 –30 –15
–340
2.7
2435 G16
3.1
3.5
3.9 4.3
VCC (V)
4.7
5.1
5.5
2435 G17
FO = GND
REF– = GND
TA = 25°C
VCC = 5V
VIN = 0V
VINCM = GND
–1.67
–338
90
Offset Error vs VREF
–1.64
–336
75
6
–1.63
–338
0 15 30 45 60
TEMPERATURE (°C)
5
–1.62
–332
–334
4
–1.61
VIN = 0V
VINCM = GND
–326 FO = GND
TA = 25°C
–328
–324
–330
–332
3
2
VINCM (V)
2435 G15
OFFSET ERROR (mV)
OFFSET ERROR (ppm OF VREF)
–324
VCC = 5V
VREF = 5V
VIN = 0V
VINCM = GND
FO = GND
5
OFFSET ERROR (ppm OF VREF)
–322
VCC = 5V
–334 REF+ = 5V
REF– = GND
–336
VIN = 0V
–338 FO = GND
TA = 25°C
–340
–1
1
0
2435 G14
Offset Error vs Temperature
–320
Offset Error vs VINCM
–324
3.6
3.2
100
–322
3.8
3.4
3.1
–320
4.0
3.2
2.7
75
2435 G12
RMS Noise vs VREF
FO = GND
4.8 REF– = GND
T = 25°C
4.6 VA = 5V
CC
4.4 VIN = 0V
VINCM = GND
4.2
3.4
3.0
50
25
0
TEMPERATURE (°C)
OFFSET ERROR (ppm OF VREF)
RMS NOISE (μV)
FO = GND
4.8 REF+ = VCC
REF– = GND
4.6 T = 25°C
A
4.4 VIN = 0V
VINCM = GND
4.2
–25
2435 G11
RMS Noise vs VCC = VREF
5.0
3.0
–50
6
5
2435 G10
RMS NOISE (μV)
FO = GND
4.8 VCC = 5V
= 5V
V
4.6 VREF= 0V
IN
4.4 VINCM = GND
3.4
2.5
RMS Noise vs Temperature (TA)
–1.70
0
1
3
2
VREF (V)
4
5
2435 G18
24351fc
For more information www.linear.com/LTC2435
7
LTC2435/LTC2435-1
Typical Performance Characteristics
–300
+FS ERROR
–350
–FS ERROR
–360
–370
–60 –40 –20
20 40 60
0
TEMPERATURE (°C)
80
–500
–FS ERROR
–600
–700
–800
–900
2.7
100
VREF = 2.5V
REF– = GND
VINCM = 0.5VREF
FO = GND
TA = 25°C
+FS ERROR
–400
3.1
3.5
3.9 4.3
VCC (V)
4.7
2435 G19
VREF = 2.5V
REF– = GND
= 0.5VREF
V
15 INCM
FO = GND
TA = 25°C
10
5
0
–5
2.7
5.5
REJECTION (dB)
–80
–80
–120
–120
–120
–140
0 20 40 60 80 100 120 140 160 180 200 220
FREQUENCY AT VCC (Hz)
1
10
–140
13800
100 1000 10000 100000 1000000
FREQUENCY AT VCC (Hz)
PSRR vs Frequency at VCC
(LTC2435)
REJECTION (dB)
REJECTION (dB)
VCC = 4.1VDC
REF+ = 2.5V
–20 REF– = GND
IN+ = GND
–40 IN– = GND
FO = GND
–60 TA = 25°C
–80
VCC = 4.1VDC ±0.7V
REF+ = 2.5V
–20 REF– = GND
IN+ = GND
–40 IN– = GND
FO = GND
–60 TA = 25°C
–80
–100
–120
–120
–120
80
120
160
200
FREQUENCY AT VCC (Hz)
240
2435 G25
–140
1
10
14000
0
0
–100
40
13900
13950
FREQUENCY AT VCC (Hz)
PSRR vs Frequency at VCC
(LTC2435)
–100
0
5.5
2435 G24
PSRR vs Frequency at VCC
(LTC2435)
0
–140
13850
2435 G23
2435 G22
5.1
–80
–100
–80
4.7
VCC = 4.1VDC ±0.7V
REF+ = 2.5V
–20 REF– = GND
IN+ = GND
–40 IN– = GND
FO = GND
–60 TA = 25°C
–100
VCC = 4.1VDC ±1.4V
REF+ = 2.5V
–20 REF– = GND
IN+ = GND
–40 IN– = GND
FO = GND
–60 TA = 25°C
3.9 4.3
VCC (V)
0
VCC = 4.1VDC
REF+ = 2.5V
–20 REF– = GND
IN+ = GND
–40 IN– = GND
FO = GND
–60 TA = 25°C
–100
–140
3.5
PSRR vs Frequency at VCC
(LTC2435-1)
0
VCC = 4.1VDC ±1.4V
REF+ = 2.5V
–20 REF– = GND
IN+ = GND
–
–40 IN = GND
FO = GND
T = 25°C
–60 A
3.1
2435 G21
PSRR vs Frequency at VCC
(LTC2435-1)
0
REJECTION (dB)
5.1
+Full-Scale Gain Error vs VCC
2435 G20
PSRR vs Frequency at VCC
(LTC2435-1)
REJECTION (dB)
20
REJECTION (dB)
–340
FULL-SCALE ERROR(ppm OF VREF)
FO = GND
VCC = 5V
VREF = 5V
VINCM = 2.5V
Full-Scale Error vs VCC
+FS GAIN ERROR (ppm OF VREF)
Full-Scale Error vs Temperature
FULL-SCALE ERROR (ppm OF VREF)
–330
100 1000 10000 100000 1000000
FREQUENCY AT VCC (Hz)
2435 G26
–140
15250
15300
15350
15400
FREQUENCY AT VCC (Hz)
15450
2435 G27
24351fc
8
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Typical Performance Characteristics
1000
240
VCC = 5.5V
230
VCC = 5V
220
210
FO = GND
CS = GND
200
SCK = NC
SDO = NC
190
VCC = 3V
180
170
800
700
600
500
15
30
45
60
75
6
VCC = 5V
300
200
100
90
TEMPERATURE (°C)
0
21
VCC = VREF = 5V
0
–10
–20
VCC = 2.7V
VREF = 2.5V
–30
–40 * RELATIVE TO OFFSET AT
NORMAL OUTPUT RATE
–50
0 20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
2435 G31
3
VCC = 5V
2
VCC = 3V
1
VCC = 2.7V
0
15
30
60
75
90
2435 G30
Resolution (INLMAX ≤ 1LSB) vs
Output Data Rate
21
20
VCC = VREF = 5V
20
19
45
TEMPERATURE (°C)
22
RESOLUTION (BITS)
OFFSET CHANGE* (ppm OF VREF)
10
VCC = 5.5V
4
Resolution (NoiseRMS ≤ 1LSB) vs
Output Data Rate
Offset Change* vs Output Data
Rate
VINCM = VREFCM
40 VIN = 0V
REF– = GND
30 F = EXT OSC
O
20 TA = 25°C
5
2435 G29
2435 G28
50
FO = GND
CS = VCC
SCK = NC
SDO = NC
0
–45 –30 –15
10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
VCC = 2.7V
VREF = 2.5V
18
VINCM = VREFCM
17 VIN –= 0V
REF = GND
F = EXT OSC
16 O
TA = 25°C
RES = LOG2 (VREF/NOISERMS)
15
0 20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
2435 G32
RESOLUTION (BITS)
0
Sleep-Mode Current vs
Temperature
VCC = 3V
400
VCC = 2.7V
160
–45 –30 –15
VREF = VCC
IN+ = GND
IN– = GND
SCK = NC
SDO = NC
SDI = GND
CS = GND
FO = EXT OSC
TA = 25°C
900
SUPPLY CURRENT (μA)
CONVERSION CURRENT (μA)
Conversion Current vs
Output Data Rate
SLEEP-MODE CURRENT (μA)
Conversion Current vs
Temperature
VCC = VREF = 5V
19
18
VCC = 2.7V
VREF = 2.5V
17
VINCM = VREFCM
16 VIN –= 0V
REF = GND
F = EXT OSC
15 O
TA = 25°C
RES = LOG2 (VREF/INLMAX)
14
0 20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
2435 G33
24351fc
For more information www.linear.com/LTC2435
9
LTC2435/LTC2435-1
Pin Functions
GND (Pins 1, 7, 8, 9, 10, 15, 16): Ground. Multiple ground
pins internally connected for optimum ground current
flow and VCC decoupling. Connect each one of these pins
to a ground plane through a low impedance connection.
All seven pins must be connected to ground for proper
operation.
SDO (Pin 12): Three-State Digital Output. During the Data
Output period, this pin is used as serial data output. When
the chip select CS is HIGH (CS = VCC) the SDO pin is in a
high impedance state. During the Conversion and Sleep
periods, this pin is used as the conversion status output.
The conversion status can be observed by pulling CS LOW.
VCC (Pin 2): Positive Supply Voltage. Bypass to GND
(Pin 1) with a 10µF tantalum capacitor in parallel with
0.1µF ceramic capacitor as close to the part as possible.
SCK (Pin 13): Bidirectional Digital Clock Pin. In Internal
Serial Clock Operation mode, SCK is used as digital output
for the internal serial interface clock during the Data Output
period. In External Serial Clock Operation mode, SCK is
used as digital input for the external serial interface clock
during the Data Output period. A weak internal pull-up is
automatically activated in Internal Serial Clock Operation
mode. The Serial Clock Operation mode is determined by
the logic level applied to the SCK pin at power up or during
the most recent falling edge of CS.
REF + (Pin 3), REF– (Pin 4): Differential Reference Input.
The voltage on these pins can have any value between
GND and VCC as long as the reference positive input, REF+,
is maintained more positive than the reference negative
input, REF –, by at least 0.1V.
IN + (Pin 5), IN– (Pin 6): Differential Analog Input. The voltage on these pins can have any value between GND – 0.3V
and VCC + 0.3V. Within these limits the converter bipolar
input range (VIN = IN+ – IN–) extends from – 0.5•(VREF)
to 0.5•(VREF). Outside this input range the converter
produces unique overrange and underrange output codes.
CS (Pin 11): Active LOW Digital Input. A LOW on this pin
enables the SDO digital output and wakes up the ADC.
Following each conversion, the ADC automatically enters
the Sleep mode and remains in this low power state as
long as CS is HIGH. A LOW-to-HIGH transition on CS
during the Data Output transfer aborts the data transfer
and starts a new conversion.
FO (Pin 14): Frequency Control Pin. Digital input that
controls the ADC’s notch frequencies and conversion time.
When the FO pin is connected to VCC (LTC2435 only), the
converter uses its internal oscillator and the digital filter
first null is located at 50Hz. When the FO pin is connected
to GND (FO = OV), the converter uses its internal oscillator
and the digital filter first null is located at 60Hz (LTC2435)
or simultaneous 50Hz/60Hz (LTC2435-1). When FO is
driven by an external clock signal with a frequency fEOSC,
the converter uses this signal as its system clock and the
digital filter first null is located at a frequency fEOSC /2560.
24351fc
10
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Functional Block Diagram
INTERNAL
OSCILLATOR
VCC
GND
IN+
IN–
AUTOCALIBRATION
AND CONTROL
+
–∫
∫
FO
(INT/EXT)
∫
SDO
∑
SERIAL
INTERFACE
ADC
SCK
CS
REF+
REF–
DECIMATING FIR
– +
DAC
2435 F01
Figure 1. Functional Block Diagram
Test Circuits
VCC
SDO
1.69k
1.69k
CLOAD = 20pF
SDO
Hi-Z TO VOH
VOL TO VOH
VOH TO Hi-Z
CLOAD = 20pF
2435 TA03
Hi-Z TO VOL
VOH TO VOL
VOL TO Hi-Z
2435 TA04
24351fc
For more information www.linear.com/LTC2435
11
LTC2435/LTC2435-1
Applications Information
Converter Operation
Converter Operation Cycle
The LTC2435/LTC2435-1 are low power, delta-sigma
analog-to-digital converters with an easy to use 3-wire
serial interface (see Figure 1). Their operation is made
up of three states. The converter operating cycle begins
with the conversion, followed by the sleep state and ends
with the data output (see Figure 2). The 3-wire interface
consists of serial data output (SDO), serial clock (SCK)
and chip select (CS).
CONVERT
SLEEP
FALSE
There is no latency in the conversion result. The data output
corresponds to the conversion just performed. This result
is shifted out on the serial data out pin (SDO) under the
control of the serial clock (SCK). Data is updated on the
falling edge of SCK allowing the user to reliably latch data
on the rising edge of SCK (see Figure 3). The data output
state is concluded once 24 bits are read out of the ADC
or when CS is brought HIGH. The device automatically
initiates a new conversion and the cycle repeats.
Through timing control of the CS and SCK pins, the
LTC2435/LTC2435-1 offer several flexible modes of
operation (internal or external SCK and free-running
conversion modes). These various modes do not require
programming configuration registers; moreover, they do
not disturb the cyclic operation described above. These
modes of operation are described in detail in the Serial
Interface Timing Modes section.
Conversion Clock
CS = LOW
AND
SCK
TRUE
DATA OUTPUT
2435 F02
Figure 2. LTC2435 State Transition Diagram
Initially, the LTC2435/LTC2435-1 perform a conversion.
Once the conversion is complete, the device enters the
sleep state. While in this sleep state, power consumption
is reduced by an order of magnitude if CS is HIGH. The
part remains in the sleep state as long as CS is HIGH.
The conversion result is held indefinitely in a static shift
register while the converter is in the sleep state.
Once CS is pulled LOW, the device exits the low power
sleep mode and enters the data output state. If CS is pulled
HIGH before the first rising edge of SCK, the device returns
to the sleep mode and the conversion result is still held in
the internal static shift register. If CS remains LOW after
the first rising edge of SCK, the device begins outputting
the conversion result. Taking CS HIGH at this point will
terminate the data output state and start a new conversion.
A major advantage the delta-sigma converter offers over
conventional type converters is an on-chip digital filter
(commonly implemented as a Sinc or Comb filter). For
high resolution, low frequency applications, this filter is
typically designed to reject line frequencies of 50Hz or 60Hz
plus their harmonics. The filter rejection performance is
directly related to the accuracy of the converter system
clock. The LTC2435/LTC2435-1 incorporate a highly
accurate on-chip oscillator. This eliminates the need for
external frequency setting components such as crystals
or oscillators. Clocked by the on-chip oscillator, the
LTC2435 achieves a minimum of 110dB rejection at the
line frequency (50Hz or 60Hz ± 2%), while the LTC2435‑1
achieves a minimum of 87db rejection at 50Hz ±2% and
60Hz ±2% simultaneously.
Ease of Use
The LTC2435/LTC2435-1 data output has no latency,
filter settling delay or redundant data associated with the
conversion cycle. There is a one-to-one correspondence
between the conversion and the output data. Therefore,
multiplexing multiple analog voltages is easy.
24351fc
12
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Applications Information
The LTC2435/LTC2435-1 perform a full-scale calibration
every conversion cycle. This calibration is transparent to
the user and has no effect on the cyclic operation described
above. The advantage of continuous calibration is extreme
stability of full-scale readings with respect to time, supply
voltage change and temperature drift.
Unlike the LTC2430, the LTC2435 and LTC2435-1 do not
perform an offset calibration every conversion cycle. This
enables the LTC2435/LTC2435-1 to double their output rate
while maintaining line frequency rejection. The initial offset
of the LTC2435/LTC2435-1 is within 5mV independent of
VREF . Based on the LTC2435/LTC2435-1 new modulator
architecture, the temperature drift of the offset is less than
100nV/°C. More information on the LTC2435/LTC2435‑1
offset is described in the Offset Accuracy and Drift section
of this data sheet.
Power-Up Sequence
The LTC2435/LTC2435-1 automatically enter an internal
reset state when the power supply voltage VCC drops
below approximately 2.2V. This feature guarantees the
integrity of the conversion result and of the serial interface
mode selection. (See the 2-wire I/O sections in the Serial
Interface Timing Modes section.)
When the VCC voltage rises above this critical threshold,
the converter creates an internal power-on-reset (POR)
signal with a duration of approximately 1ms. The POR signal
clears all internal registers. Following the POR signal, the
LTC2435/LTC2435-1 start a normal conversion cycle and
follow the succession of states described above. The first
conversion result following POR is accurate within the
specifications of the device if the power supply voltage is
restored within the operating range (2.7V to 5.5V) before
the end of the POR time interval.
Reference Voltage Range
These converters accept a truly differential external
reference voltage. The absolute/common mode voltage
specification for the REF + and REF – pins covers the entire
range from GND to VCC. For correct converter operation, the
REF + pin must always be more positive than the REF – pin.
The LTC2435/LTC2435-1 can accept a differential reference
voltage from 0.1V to VCC. The converter output noise is
determined by the thermal noise of the front-end circuits,
and as such, its value is nearly constant with reference
voltage. A decrease in reference voltage will not significantly improve the converter’s effective resolution. On the
other hand, a reduced reference voltage will improve the
converter’s overall INL performance. A reduced reference
voltage will also improve the converter performance when
operated with an external conversion clock (external FO
signal) at substantially higher output data rates (see the
Output Data Rate section).
Input Voltage Range
The analog input is truly differential with an absolute/common mode range for the IN+ and IN– input pins extending
from GND – 0.3V to VCC + 0.3V. Outside these limits, the
ESD protection devices begin to turn on and the errors
due to input leakage current increase rapidly. Within these
limits, the LTC2435/LTC2435-1 convert the bipolar differential input signal, VIN = IN+ – IN–, from – FS = –0.5
• VREF to + FS = 0.5 • VREF where VREF = REF+ – REF–.
Outside this range, the converters indicate the overrange
or the underrange condition using distinct output codes.
Input signals applied to IN+ and IN– pins may extend by
300mV below ground and above VCC. In order to limit any
fault current, resistors of up to 5k may be added in series
with the IN+ and IN– pins without affecting the performance of the device. In the physical layout, it is important
to maintain the parasitic capacitance of the connection
between these series resistors and the corresponding
pins as low as possible; therefore, the resistors should
be located as close as practical to the pins. The effect of
the series resistance on the converter accuracy can be
evaluated from the curves presented in the Input Current/
Reference Current sections. In addition, series resistors
will introduce a temperature dependent offset error due
to the input leakage current. A 1nA input leakage current
will develop a 1ppm offset error on a 5k resistor if VREF =
5V. This error has a very strong temperature dependency.
24351fc
For more information www.linear.com/LTC2435
13
LTC2435/LTC2435-1
applications information
Output Data Format
The LTC2435/LTC2435-1 serial output data stream is 24
bits long. The first 3 bits represent status information
indicating the sign and conversion state. The next 21
bits are the conversion result, MSB first. The third and
fourth bit together are also used to indicate an underrange
condition (the differential input voltage is below –FS) or
an overrange condition (the differential input voltage is
above +FS).
Bit 23 (first output bit) is the end of conversion (EOC)
indicator. This bit is available at the SDO pin during the
conversion and sleep states whenever the CS pin is LOW.
This bit is HIGH during the conversion and goes LOW
when the conversion is complete.
Bit 22 (second output bit) is a dummy bit (DMY) and is
always LOW.
Bit 21 (third output bit) is the conversion result sign
indicator (SIG). If VIN is >0, this bit is HIGH. If VIN is 0.01µF) may
be required as reference filters in certain configurations.
Such capacitors will average the reference sampling charge
and the external source resistance will see a quasi constant reference differential impedance. For the LTC2435,
when FO = LOW (internal oscillator and 60Hz notch), the
typical differential reference resistance is 15.6MΩ which
will generate a +FS gain error of approximately 0.032ppm
E: ∆RIN = –200Ω
A: ∆RIN = 1k
B: ∆RIN = 500Ω F: ∆RIN = –500Ω
C: ∆RIN = 200Ω G: ∆RIN = –1k
D: ∆RIN = 0Ω
–330
B
C
–340
D
–350
–360
–370
–380
A
E
VCC = 5V
FO = GND
VREF+ = 5V
TA = 25°C
VREF– = GND CIN = 10µF
VIN+ = VIN– = VINCM
F
G
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
VINCM (V)
2435 F20
Figure 20. Offset Error vs Common Mode Voltage (VINCM = VIN+ = VIN–)
and Input Source Resistance Imbalance (∆RIN = RSOURCEIN+ – RSOURCEIN–)
for Large CIN Values (CIN ≥ 1µF)
24351fc
For more information www.linear.com/LTC2435
29
LTC2435/LTC2435-1
Applications Information
for each ohm of source resistance driving REF+ or REF–.
When FO = HIGH (internal oscillator and 50Hz notch), the
typical differential reference resistance is 18.7MΩ which
will generate a +FS gain error of approximately 0.027ppm
for each ohm of source resistance driving REF+ or REF–.
For the LTC2435‑1, the typical differential reference resistance is 17.1MΩ which will generate a +FS gain error of
approximately 0.029ppm for each ohm of source resistance
driving REF + or REF–. When FO is driven by an external
oscillator with a frequency fEOSC (external conversion clock
VCC = 5V
VREF+ = 5V
VREF– = GND
VIN+ = 3.75V
VIN– = 1.25V
FO = GND
TA = 25°C
+FS ERROR VARIATION (ppm)
90
80
70
60
50
10
CIN = 100pF
CIN = 0.001μF
40
30
20
10
0
–10
CIN = 0pF
1
10
1000
100
RSOURCE (Ω)
CIN = 0pF
0
CIN = 0.01μF
–FS ERROR VARIATION (ppm)
100
operation), the typical differential reference resistance is 2.4
• 1012/fEOSCΩ and each ohm of source resistance driving
REF+ or REF– will result in 0.21 • 10–6 • fEOSCppm +FS
gain error. The effect of the source resistance on the two
reference pins is additive with respect to this gain error.
The typical +FS and –FS errors for various combinations
of source resistance seen by the REF+ and REF– pins and
external capacitance CREF connected to these pins are
shown in Figures 21, 22, 23 and 24.
10000 100000
CIN = 0.01μF
–10
–20
–30
CIN = 0.001μF
–40
–50
VCC = 5V
VREF+ = 5V
VREF– = GND
VIN+ = 1.25V
VIN– = 3.75V
FO = GND
TA = 25°C
–60
–70
–80
–90
–100
1
10
CIN = 100pF
1000
100
RSOURCE (Ω)
10000 100000
2435 F22
2435 F21
Figure 21. +FS Error vs RSOURCE at REF+ or REF– (Small CIN)
Figure 22. –FS Error vs RSOURCE at REF+ or REF– (Small CIN)
0
VCC = 5V
90 VREF+ = 5V
V – = GND
80 VREF
IN+ = 3.75V
70 VIN– = 1.25V
FO = GND
60 TA = 25°C
–10
CIN = 1μF, 10μF
50
CIN = 0.1μF
40
30
20
CIN = 0.01μF
10
0
0
400
800
1200
RSOURCE (Ω)
1600
2000
–FS ERROR VARIATION (ppm)
+FS ERROR VARIATION (ppm)
100
–30
–40
–50
–60 VCC = 5V
VREF+ = 5V
–70 VREF– = GND
V + = 1.25V
–80 VIN– = 3.75V
IN
–90 FO = GND
TA = 25°C
–100
0
400
2435 F23
Figure 23. +FS Error vs RSOURCE at REF+ and REF– (Large CREF)
CIN = 0.01μF
–20
CIN = 0.1μF
CIN = 1μF, 10μF
800
1200
RSOURCE (Ω)
1600
2000
2435 F24
Figure 24. –FS Error vs RSOURCE at REF+ and REF– (Large CREF)
24351fc
30
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Applications Information
In addition to this gain error, the converter INL performance
is degraded by the reference source impedance. When FO
= LOW (internal oscillator and 60Hz notch), every 100Ω
of source resistance driving REF+ or REF– translates into
about 0.11ppm additional INL error. For the LTC2435,
when FO = HIGH (internal oscillator and 50Hz notch), every
100Ω of source resistance driving REF+ or REF– translates into about 0.092ppm additional INL error; and for
the LTC2435‑1 operating with simultaneous 50Hz/60Hz
rejection, every 100Ω of source resistance leads to an
additional 0.10ppm of additional INL error. When FO is
driven by an external oscillator with a frequency fEOSC,
every 100Ω of source resistance driving REF+ or REF–
translates into about 0.73 • 10–6 • fEOSCppm additional
INL error. Figure 25 shows the typical INL error due to the
source resistance driving the REF+ or REF– pins when large
CREF values are used. The effect of the source resistance
on the two reference pins is additive with respect to this
INL error. In general, matching of source impedance for
the REF+ and REF– pins does not help the gain or the INL
error. The user is thus advised to minimize the combined
source impedance driving the REF+ and REF– pins rather
than to try to match it.
The magnitude of the dynamic reference current depends
upon the size of the very stable internal sampling capacitors
and upon the accuracy of the converter sampling clock. The
accuracy of the internal clock over the entire temperature
and power supply range is typical better than 0.5%. Such
a specification can also be easily achieved by an external
clock. When relatively stable resistors (50ppm/°C) are
used for the external source impedance seen by REF+
and REF–, the expected drift of the dynamic current gain
error will be insignificant (about 1% of its value over the
entire temperature and voltage range). Even for the most
stringent applications a one-time calibration operation
may be sufficient.
In addition to the reference sampling charge, the reference pins ESD protection diodes have a temperature dependent leakage current. This leakage current, nominally
1nA (±10nA max), results in a small gain error. A 100Ω
source resistance will create a 0.05µV typical and 0.5µV
maximum full-scale error.
INL (ppm OF VREF)
15
VINCM = 0.5 • (IN+ + IN–) = 2.5V
12 VCC = 5V
REF+ = 5V
9 REF– = GND
6 FO = GND
CREF = 10μF
3 TA = 25°C
0
–3
–6
RSOURCE = 1k
RSOURCE = 5k
–9
–12
RSOURCE = 10k
–15
–0.5 –0.4 –0.3 –0.2 –0.1 0 0.1 0.2 0.3 0.4 0.5
VINDIF/VREFDIF (V)
2435 F25
Figure 25. INL vs Differential Input Voltage (VIN = IN+ – IN–)
and Reference Source Resistance (RSOURCE at REF+ and
REF– for Large CREF Values (CREF ≥ 1µF)
24351fc
For more information www.linear.com/LTC2435
31
LTC2435/LTC2435-1
applications information
Output Data Rate
When using its internal oscillator, the LTC2435 can produce
up to 15 readings per second with a notch frequency of
60Hz (FO = LOW) and 12.5 readings per second with a
notch frequency of 50Hz (FO = HIGH) and the LTC2435-1
can produce up to 13.6 readings per second with FO = LOW.
The actual output data rate will depend upon the length of
the sleep and data output phases which are controlled by
the user and which can be made insignificantly short. When
operated with an external conversion clock (FO connected
to an external oscillator), the LTC2435/LTC2435-1 output
data rate can be increased as desired. The duration of the
conversion phase is 10278/fEOSC. If fEOSC = 153600Hz, the
converter behaves as if the internal oscillator is used and
the notch is set at 60Hz. There is no significant difference
in the LTC2435/LTC2435-1 performance between these
two operation modes.
An increase in fEOSC over the nominal 153600Hz will
translate into a proportional increase in the maximum
output data rate. This substantial advantage is nevertheless
accompanied by three potential effects, which must be
carefully considered.
First, a change in fEOSC will result in a proportional change
in the internal notch position and in a reduction of the
converter differential mode rejection at the power line frequency. In many applications, the subsequent performance
degradation can be substantially reduced by relying upon
the LTC2435/LTC2435-1’s exceptional common mode
rejection and by carefully eliminating common mode to
differential mode conversion sources in the input circuit.
–320
TA = 25°C
–320
TA = 85°C
–330
–340
–350
0
Third, the internal analog circuits are optimized for normal
operation; therefore an increase in the frequency of the
external oscillator will start to decrease the effectiveness of
the internal analog circuits. This will result in a progressive
degradation in the converter accuracy and linearity. Typical
measured performance curves for output data rates up to
200 readings per second are shown in Figures 26 to 33.
The degradation becomes more obvious above output data
rate of 150Hz, which corresponds to an external oscillator
of 1.536MHz. In order to obtain the highest possible level
of accuracy from this converter at output data rates above
150 readings per second, the user is advised to maximize
the power supply voltage used and to limit the maximum
ambient operating temperature. In certain circumstances,
a reduction of the differential reference voltage may be
beneficial.
–300
VINCM = VREFCM
VCC = VREF = 5V
VIN = 0V
FO = EXT OSC
–310
Second, the increase in clock frequency will increase
proportionally the amount of sampling charge transferred
through the input and the reference pins. If large external
input and/or reference capacitors (CIN, CREF) are used, the
previous section provides formulae for evaluating the effect
of the source resistance upon the converter performance for
any value of fEOSC. If small external input and/or reference
capacitors (CIN, CREF) are used, the effect of the external
source resistance upon the LTC2435/LTC2435‑1 typical
performance can be inferred from Figures 16, 17, 21 and
22 in which the horizontal axis is scaled by 153600/fEOSC.
+FS ERROR (ppm OF VREF)
OFFSET ERROR (ppm OF VREF)
–300
The user should avoid single-ended input filters and should
maintain a very high degree of matching and symmetry
in the circuits driving the IN+ and IN– pins.
20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
–340
–360
–380
–400
TA = 85°C
–420
–440
–460
VINCM = VREFCM
–480 VCC = VREF = 5V
FO = EXT OSC
–500
0 20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
2435 F27
2435 F26
Figure 26. Offset Error vs Output Data Rate and Temperature
TA = 25°C
Figure 27. + FS Error vs Output Data Rate and Temperature
24351fc
32
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Applications Information
22
VINCM = VREFCM
–220 VCC = VREF = 5V
FO = EXT OSC
–240
21
–260
RESOLUTION (BITS)
–FS ERROR (ppm OF VREF)
–200
–280
–300
–320
–340
TA = 25°C
–360
TA = 85°C
20
19
18
VCC = VREF = 5V
VINCM = VREFCM
VIN = 0V
REF– = GND
FO = EXT OSC
RES = LOG2(VREF/NOISERMS)
17
16
–380
–400
TA = 25°C
TA = 85°C
0
15
20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
0
2435 F29
2435 F28
Figure 29. Resolution (NoiseRMS ≤ 1LSB)
vs Output Data Rate and Temperature
Figure 28. – FS Error vs Output Data Rate and Temperature
50
21
RESOLUTION (BITS)
19
TA = 25°C
18
17
TA = 85°C
16 VCC = VREF = 5V
VINCM = VREFCM
REF– = GND
15
FO = EXT OSC
RES = LOG2 (VREF/INLMAX)
14
0 20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
OFFSET CHANGE* (ppm OF VREF)
40
20
30
20
VINCM = VREFCM
VIN = 0V
REF– = GND
FO = EXT OSC
TA = 25°C
10
VCC = VREF = 5V
0
VCC = 2.7V
VREF = 2.5V
–10
–20
–30
–40 * RELATIVE TO OFFSET AT
NORMAL OUTPUT RATE
–50
0 20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
2435 F30
2435 F31
Figure 30. Resolution (INLRMS ≤ 1LSB)
vs Output Data Rate and Temperature
Figure 31. Offset Change* vs Output
Data Rate and Reference Voltage
22
21
20
VCC = VREF = 5V
20
RESOLUTION (BITS)
RESOLUTION (BITS)
21
VCC = 2.7V
VREF = 2.5V
19
18
VINCM = VREFCM
VIN = 0V
REF– = GND
FO = EXT OSC
TA = 25°C
RES = LOG2(VREF/NOISERMS)
17
16
15
0
20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
18
VCC = 2.7V
VREF = 2.5V
17
VINCM = VREFCM
16 VIN –= 0V
REF = GND
F = EXT OSC
15 O
TA = 25°C
RES = LOG2 (VREF/INLMAX)
14
0 20 40 60 80 100 120 140 160 180 200
OUTPUT DATA RATE (READINGS/SEC)
2435 F32
Figure 32. Resolution (NoiseRMS ≤ 1LSB)
vs Output Data Rate and Reference Voltage
VCC = VREF = 5V
19
2435 F33
Figure 33. Resolution (INLMAX ≤ 1LSB)
vs Output Data Rate and Reference Voltage
24351fc
For more information www.linear.com/LTC2435
33
LTC2435/LTC2435-1
applications information
Normal Mode Rejection and Anti-Aliasing
One of the advantages delta-sigma ADCs offer over
conventional ADCs is on-chip digital filtering. Combined
with a large oversampling ratio, the LTC2435/LTC2435-1
significantly simplifies anti-aliasing filter requirements.
The SINC4 digital filter provides greater than 120dB normal
mode rejection at all frequencies except DC and integer
multiples of the modulator sampling frequency (fS). Independent of the operating mode, fS = 256 • fN = 1024 •
fOUTMAX where fN is the notch frequency and fOUTMAX is
the maximum output data rate. In the internal oscillator
mode, for the LTC2435, FS = 12800Hz with a 50Hz notch
0
The normal mode rejection performance is shown in Figure 34. The regions of low rejection occurring at integer
multiples of fS have a very narrow bandwidth. Magnified
details of the normal mode rejection curves are shown
in Figure 35 (rejection near DC) and Figure 36 (rejection
at fS = 256fN) where fN represents the notch frequency.
For the LTC2435, the bandwidth is 13.6Hz (FO = GND)
and 11.4Hz (FO = VCC). The bandwidth is 12.4Hz for the
LTC2435-1 (FO = GND).
0
FO = HIGH
–10
INPUT NORMAL MODE REJECTION (dB)
setting and fS = 15360Hz with a 60Hz notch setting. For
the LTC2435-1, fS = 13980Hz (FO = LOW). In the external
oscillator mode, fS = fEOSC/10.
–20
–20
–30
–40
REJECTION (dB)
–40
–50
–60
–70
–80
–60
–80
–100
–90
–100
–120
–110
–120
0 fS 2fS 3fS 4fS 5fS 6fS 7fS 8fS 9fS 10fS11fS12fS
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
–140
0
0
–20
–20
INPUT NORMAL REJECTION (dB)
INPUT NORMAL REJECTION (dB)
Figure 34b. Input Normal Mode Rejection, Internal
Oscillator and FO = Low or External Oscillator
0
–40
–60
–80
–100
–120
0
fN
2fN 3fN 4fN 5fN 6fN 7fN
INPUT SIGNAL FREQUENCY (fN)
8fN
–40
–60
–80
–100
–120
248 250 252 254 256 258 260 262 264
INPUT SIGNAL FREQUENCY (fN)
2435 F36
2435 F35
Figure 35. Input Normal Mode Rejection
fS
2435 F34b
2435 F34a
Figure 34a. Input Normal Mode Rejection,
Internal Oscillator and 50Hz Notch (LTC2435)
fS/2
INPUT FREQUENCY
Figure 36. Input Normal Mode Rejection
24351fc
34
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Applications Information
Through FO connection, the LTC2435 provides better than
110dB input differential mode rejection at 50Hz or 60Hz
±2%. While for the LTC2435-1, it has a notch frequency
of about 55Hz with better than 70db rejection over 48Hz
to 62.4Hz, which covers both 50Hz ±2% and 60Hz ±2%.
In order to achieve better rejection over the range of
48Hz to 62.4Hz, a running average can be performed. By
averaging two consecutive LTC2435-1 readings, a SINC1
notch is combined with the SINC4 digital filter, yielding
the frequency response shown in Figure 37. The averaging operation still keeps the output rate with the following
algorithm:
Result 1 = average (sample 0, sample 1)
Result 2 = average (sample 1, sample 2)
Result n = average (sample n-1, sample n)
The user can expect to achieve in practice this level of
performance using the internal oscillator as it is demonstrated by Figures 38 to 40. Typical measured values of
the normal mode rejection of the LTC2435-1 operating
with an internal oscillator and a 54.6Hz notch setting
are shown in Figure 38 and 39 superimposed over the
theoretical calculated curve. The same normal mode
rejection performance is obtained for the LTC2435 with
the frequency scaled to have the notch frequency at 60Hz
(FO = GND) or 50Hz (FO = VCC).
As a result of these remarkable normal mode specifications, minimal (if any) anti-alias filtering is required in front
of the LTC2435/LTC2435-1. If passive RC components
are placed in front of the LTC2435/LTC2435-1, the input
dynamic current should be considered (see Input Current
section). In cases where large effective RC time constants
are used, an external buffer amplifier may be required to
minimize the effects of dynamic input current.
Traditional high order delta-sigma modulators, while
providing very good linearity and resolution, suffer from
potential instabilities at large input signal levels. The
proprietary architecture used for the LTC2435/LTC2435-1
third order modulator resolves this problem and guarantees a predictable stable behavior at input signal levels of
0
–80
NORMAL MODE REJECTION (dB)
NORMAL MODE REJECTION (dB)
–70
NO AVERAGE
–90
–100
–110
WITH
RUNNING
AVERAGE
–120
–20
–40
–60
–80
–100
–130
–140
MEASURED DATA
VCC = 5V
CALCULATED DATA VREF = 5V
REF– = GND
VINCM = 2.5V
VIN(P-P) = 5V
FO = GND
TA = 25°C
60
62
54 56
58
48 50
52
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
–120
2435 F37
Figure 37. LTC2435-1 Input Normal Mode Rejection
0
25
50 75 100 125 150 175 200 225
INPUT FREQUENCY (Hz)
2435 F38
Figure 38. Input Normal Mode Rejection
vs Input Frequency (LTC2435-1)
24351fc
For more information www.linear.com/LTC2435
35
LTC2435/LTC2435-1
applications information
up to 150% of full scale. In many industrial applications,
it is not uncommon to have to measure microvolt level
signals superimposed over volt level perturbations and
LTC2435/LTC2435-1 are eminently suited for such tasks.
When the perturbation is differential, the specification of
interest is the normal mode rejection for large input signal
levels. With a reference voltage VREF = 5V, the LTC2435/
LTC2435-1 have a full-scale differential input range of 5V
peak-to-peak. Figure 40 shows measurement results for
the LTC2435-1 normal mode rejection ratio with a 7.5V
peak-to-peak (150% of full scale) input signal superim-
NORMAL MODE REJECTION (dB)
0
posed over the more traditional normal mode rejection
ratio results obtained with a 5V peak-to-peak (full scale)
input signal. The same performance is obtained for the
LTC2435 with the frequency scaled to have the notch
frequency at 60Hz (FO = GND) or 50Hz (FO = VCC). It is
clear that the LTC2435/LTC2435-1 rejection performance
is maintained with no compromises in this extreme situation. When operating with large input signal levels, the
user must observe that such signals do not violate the
device absolute maximum ratings.
MEASURED DATA
VCC = 5V
CALCULATED DATA VREF = 5V
REF– = GND
VINCM = 2.5V
VIN(P-P) = 5V
FO = GND
TA = 25°C
–20
–40
–60
–80
–100
–120
0
25
50 75 100 125 150 175 200 225
INPUT FREQUENCY (Hz)
2435 F39
Figure 39. Input Normal Mode Rejection
vs Input Frequency with Running Average
NORMAL MODE REJECTION (dB)
0
VIN(P-P) = 5V
VCC = 5V
VIN(P-P) = 7.5V
VREF = 5V
(150% OF FULL SCALE) REF– = GND
VINCM = 2.5V
FO = GND
TA = 25°C
–20
–40
–60
–80
–100
–120
0
25
50 75 100 125 150 175 200 225
INPUT FREQUENCY (Hz)
2435 F40
Figure 40. Measured Input Normal Mode
Rejection vs Input Frequency (fN = 54.6Hz)
24351fc
36
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Applications Information
Sample Driver for LTC2435/LTC2435-1 SPI Interface
could result in full excitation voltage at the inputs to the
multiplexer or ADC. The use of amplification prior to the
multiplexer will largely eliminate errors associated with
channel leakage developing error voltages in the source
impedance.
Figure 41 shows the use of an LTC2435/LTC2435‑1 with a
differential multiplexer. This is an inexpensive multiplexer
that will contribute some error due to leakage if used
directly with the output from the bridge, or if resistors
are inserted as a protection mechanism from overvoltage. Although the bridge output may be within the input
range of the A/D and multiplexer in normal operation,
some thought should be given to fault conditions that
The LTC2435/LTC2435‑1 have a very simple serial interface that makes interfacing to microprocessors and
microcontrollers very easy.
5V
5V
+
16
12
14
15
11
3
REF+
4
REF–
LTC2435/
LTC2435-1
74HC4052
1
5
2
TO OTHER
DEVICES
13
5
3
IN+
6
IN–
6
4
8
9
2
VCC
47μF
10
GND
1, 7, 8, 9,
10, 15, 16
2435 F41
A0
A1
Figure 41. Use a Differential Multiplexer to Expand Channel Capability
VCC
X1
20
SCK
LTC2435/ SDO
LTC2435-1
CS
13
12
11
PIC16F73
13
17
RC2
RC6
14
RC3
18
15
RC7
RC4
8
19
VCC
12
11
13
10
18
2
C1
C2
LT1180A
T1IN
T2IN
R1OUT
R2OUT
SHDN
C1+
4
C1–
5
C2+
6
C2–
T1OUT
T2OUT
R1IN
R2IN
VCC
15
8
14
9
17
3
V+
V–
1
2
3
4
5
6
7
8
9
VCC
C3
C5
7
C4
GND
16
2435 F42
Figure 42. Connecting the LTC2435/LTC2435-1 to a PIC16F73 MCU Using the SPI Serial Interface
24351fc
For more information www.linear.com/LTC2435
37
LTC2435/LTC2435-1
applications information
// Basic data collection program for the LTC2435 using the
// PIC16F73 microcontroller. Collects data as fast as possible
// and sends it out the serial port at 57600 baud as six
// hexadecimal characters, followed by a carriage return.
// This can be captured with a terminal program and analyzed
// with a spreadsheet using the HEX2DEC function (in Excel.)
//
// Written for the CCS compiler, version 3.049.
////////////////////////////////////////////////////////////////////
#include
// Synchronous serial port control
#byte SSPCON = 0x14
#byte SSPSTAT = 0x94 // registers.
#bit CKE = SSPSTAT.6
#bit CKP = SSPCON.4
#bit SSPEN = SSPCON.5
#fuses HS,NOWDT,PUT
#use delay(clock=10000000) // For baud rate calculation.
#use rs232(baud=57600,parity=N,xmit=PIN_C6,rcv=PIN_C7)
// Serial data is sent on pin C6.
#define CS_ PIN_C2 // Chip select connected to pin C2
#define CLOCK PIN_C // Clock connected to pin C3
#define SDO PIN_C4 // SDO on the LTC2435 connected to pin C4
// (this is SDI on the PIC;
// Master In, Slave Out (MISO) is less ambiguous)
void main() {
// Basic configuration, no bearing on operation of LTC2435
setup_adc_ports(NO_ANALOGS);
setup_adc(ADC_CLOCK_DIV_2);
setup_counters(RTCC_INTERNAL,RTCC_DIV_2);
setup_timer_1(T1_DISABLED);
setup_timer_2(T2_DISABLED,0,1);
setup_ccp1(CCP_OFF);
setup_ccp2(CCP_OFF);
// LTC2435 is connected to the processor’s hardware SPI port.
// This sets the port such that data is shifted on clock falling edges and
// valid on rising edges. For a 10 MHz master clock, the SPI clock frequency
// will be 2.5 MHz.
setup_spi(SPI_MASTER|SPI_L_TO_H|SPI_CLK_DIV_4|SPI_SS_DISABLED);
CKP = 0; // Set up clock edges - clock idles low, data changes on
CKE = 1; // falling edges, valid on rising edges.
while(1)
{
output_low(CS_); // Enable LTC2435
while(input(SDO)) { /* Wait for SDO to fall, indicating end of conversion.*/ }
printf(“%2X”,spi_read(0)); // Read first byte, send 2 hex characters.
printf(“%2X”,spi_read(0)); // Read second byte, send 2 hex characters.
printf(“%2X”,spi_read(0)); / Read third byte, send 2 hex characters.
printf(“\r”); // Send carriage return.
output_high(CS_);
// Conversion actually started after last data byte was read,
// but raising CS_ ensures the loop will never lock up waiting for
// a low on SDO if a clock pulse is missed for some reason.
}
}
Figure 43. A Sample Program for Data Collection from the LTC2435/LTC2435-1
Using the PIC16F73 Microcontroller.
24351fc
38
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Applications Information
The listing in Figure 43 is a data collection program for the
LTC2435/LTC2435-1 using the PIC16F73 microcontroller.
The microcontroller is configured to transfer data through
the SPI serial interface. Figure 42 shows the connection.
The LT1180A is a dual RS232 driver/receiver pair with
integral charge pump that generates RS232 voltage levels
from a single 5V supply.
The program begins by declaring variables and allocating
memory locations to store the 24-bit conversion result.
The main sequence starts with pulling CS LOW. It then
waits for SDO to go LOW to start reading data. Three
bytes are read to the MCU and the LTC2435/LTC2435-1
will automatically start a new conversion. CS is also raised
to HIGH to ensure that a new conversion is started. The
collected data are sent out through the serial port at 57600
baud. This can be captured with a terminal program and
analyzed with a spreadsheet using the HEX2DEC function.
Correlated Double Sampling with the
LTC2435/LTC2435-1
The Typical Application on the back page of this data
sheet shows the LTC2435/LTC2435-1 in a correlated
double sampling circuit that achieves a noise floor of
under 100nV. In this scheme, the polarity of the bridge is
alternated every other sample and the result is the average
of a pair of samples of opposite sign. This technique has
the benefit of canceling any fixed DC error components
in the bridge, amplifiers and the converter, as these will
alternate in polarity relative to the signal. Offset voltages
and currents, thermocouple voltages at junctions of dissimilar metals and the lower frequency components of
1/f noise are virtually eliminated.
The LTC2435/LTC2435-1 have the virtue of being able to
digitize an input voltage that is outside the range defined by
the reference, thereby providing a simple means to implement a ratiometric example of correlated double sampling.
This circuit uses a bipolar amplifier (LT1219—U1 and
U2) that has neither the lowest noise nor the highest gain.
It does, however, have an output stage that can effectively suppress the conversion spikes from the LTC2435/
LTC2435-1. The LT1219 is a C-Load™ stable amplifier
that, by design, needs at least 0.1µF output capacitance to
remain stable. The 0.1µF ceramic capacitors at the outputs
(C1 and C2) should be placed and routed to minimize lead
inductance or their effectiveness in preventing envelope
detection in the input stage will be reduced. Alternatively,
several smaller capacitors could be placed so that lead
inductance is further reduced. This is a consideration
because the frequency content of the conversion spikes
extends to 50MHz or more. The output impedance of most
op amps increases dramatically with frequency but the
effective output impedance of the LT1219 remains low,
determined by the ESR and inductance of the capacitors
above 10MHz. The conversion spikes that remain at the
output of other bipolar amplifiers pass through the feedback network and often overdrive the input of the amplifier,
producing envelope detection. RFI may also be present on
the signal lines from the bridge; C3 and C4 provide RFI
suppression at the signal input, as well as suppressing
transient voltages during bridge commutation.
The wideband noise density of the LT1219 is 33nV/√Hz,
seemingly much noisier than the lowest noise amplifiers.
However, in the region just below the 1/f corner that is
not well suppressed by the correlated double sampling,
the average noise density is similar to the noise density
of many low noise amplifiers. If the amplifier is rolled
off below about 1500Hz, the total noise bandwidth is
determined by the converter’s SINC4 filter at about 12Hz.
The use of correlated double sampling involves averaging
even numbers of samples; hence, in this situation, two
samples would be averaged to give an input-referred noise
level of about 100nVRMS.
Level shift transistors Q4 and Q5 are included to allow
excitation voltages up to the maximum recommended
for the bridge. In the case shown, if a 10V supply is
used, the excitation voltage to the bridge is 8.5V and
the outputs of the bridge are above the supply rail of the
ADC. U1 and U2 are also used to produce a level shift to
bring the outputs within the input range of the converter.
This instrumentation amplifier topology does not require
well-matched resistors in order to produce good CMRR.
However, the use of R2 requires that R3 and R6 match
well, as the common mode gain is approximately –12dB.
If the bridge is composed of four equal 350Ω resistors,
the differential component associated with mismatch
of R3 and R6 is nearly constant with either polarity of
excitation and, as with offset, its contribution is canceled.
24351fc
For more information www.linear.com/LTC2435
39
LTC2435/LTC2435-1
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
GN Package
16-Lead Plastic SSOP (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1641)
.189 – .196*
(4.801 – 4.978)
.045 ±.005
16 15 14 13 12 11 10 9
.254 MIN
.009
(0.229)
REF
.150 – .165
.229 – .244
(5.817 – 6.198)
.0165 ± .0015
.150 – .157**
(3.810 – 3.988)
.0250 BSC
RECOMMENDED SOLDER PAD LAYOUT
1
.015 ± .004
× 45°
(0.38 ± 0.10)
.007 – .0098
(0.178 – 0.249)
.0532 – .0688
(1.35 – 1.75)
2 3
4
5 6
7
8
.004 – .0098
(0.102 – 0.249)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
.008 – .012
(0.203 – 0.305)
TYP
NOTE:
1. CONTROLLING DIMENSION: INCHES
INCHES
2. DIMENSIONS ARE IN
(MILLIMETERS)
.0250
(0.635)
BSC
GN16 (SSOP) 0204
3. DRAWING NOT TO SCALE
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
24351fc
40
For more information www.linear.com/LTC2435
LTC2435/LTC2435-1
Revision History
(Revision history begins at Rev C)
REV
DATE
DESCRIPTION
C
05/13
Corrected Lead Free Finish part numbers in the Order Information section
PAGE NUMBER
2
24351fc
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LTC2435
41
LTC2435/LTC2435-1
Typical Application
Correlated Double Sampling Resolves 100nV
10V
ELIMINATE FOR 5V
OPERATION (CONNECT 2.7k
RESISTORS TO 100Ω
RESISTORS)
1.5k
1.5k
Q2
100Ω
DIFFERENCE
AMP
10V
0.1μf
Q3
3
100Ω
R2
27k
22Ω
5V
Q4
5V
22Ω
Q5
–
7
U1
LT1219
4
1k
1000pF
2.7k
2
+
5k
6
5
C1
0.1μF
SHDN
5V
R4
499Ω
R3 10k
2.7k
5
C3 2.2nF
C4 2.2nF
350Ω
×4
R5
499Ω
6
IN–
LTC2435/
LTC2435-1
3
REF+
R6 10k
1000pF
10V
POL
0.1μf
1k
74HC04
2
Q1
3
–
+
5k
6
U2
LT1219
4
R1
61.9Ω
0.1%
4
7
22Ω
IN+
REF–
GND
5
C2
0.1μF
SHDN
33Ω
100Ω
22Ω
Q1: SILICONIX Si9802DY
Q2, Q3: MMBD2907
Q4, Q5: MMBD3904
(800) 554-5565
30pF
30pF
2435 F46
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LT1019
Precision Bandgap Reference, 2.5V, 5V
3ppm/°C Drift, 0.05% Max Initial Accuracy
LT1025
Micropower Thermocouple Cold Junction Compensator
80µA Supply Current, 0.5°C Initial Accuracy
LTC1043
Dual Precision Instrumentation Switched Capacitor
Building Block
Precise Charge, Balanced Switching, Low Power
LTC1050
Precision Chopper Stabilized Op Amp
No External Components 5µV Offset, 1.6µVP-P Noise
LT1236A-5
Precision Bandgap Reference, 5V
0.05% Max Initial Accuracy, 5ppm/°C Drift
LT1460
Micropower Series Reference
0.075% Max Initial Accuracy, 10ppm/°C Max Drift,
LTC2400
24-Bit, No Latency ∆∑ ADC in SO-8
0.3ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200µA
LTC2401/LTC2402
1-/2-Channel, 24-Bit, No Latency ∆∑ ADCs in MSOP
0.6ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200µA
LTC2404/LTC2408
4-/8-Channel, 24-Bit, No Latency ∆∑ ADCs with Differential Inputs 0.3ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200µA
LTC2410
24-Bit, No Latency ∆∑ ADC with Differential Inputs
800nVRMS Noise, Pin Compatible with LTC2435
LTC2411/
LTC2411-1
24-Bit, No Latency ∆∑ ADC with Differential Inputs in MSOP
1.45µVRMS Noise, 2ppm INL,
Simultaneous 50Hz/60Hz Rejection (LTC2411-1)
LTC2413
24-Bit, No Latency ∆∑ ADC with Differential Inputs
Simultaneous 50Hz/60Hz Rejection, 800nVRMS Noise
LTC2415/
LTC2415-1
24-Bit, No Latency ∆∑ ADC with 15Hz Output Rate
Pin Compatible with the LTC2435/LTC2435-1
LTC2414/LTC2418
8-/16-Channel 24-Bit, No Latency ∆∑ ADC
0.2ppm Noise, 2ppm INL, 3ppm Total Unadjusted Errors 200µA
LTC2420
20-Bit, No Latency ∆∑ ADC in SO-8
1.2ppm Noise, 8ppm INL, Pin Compatible with LTC2400
LTC2430/LTC2431
20-Bit, No Latency ∆∑ ADC with Differential Inputs
2.8µV Noise, SSOP-16/MSOP Package
24351fc
42 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC2435
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC2435
LT 0513 REV C • PRINTED IN USA
© LINEAR TECHNOLOGY CORPORATION 2001
工商网监
湘ICP备2023018690号
