Features
Easy Drive™ Technology Enables Rail-to-Rail Inputs
with Zero Differential Input Current
n Directly Digitizes High Impedance Sensors with
Full Accuracy
n Programmable Gain from 1 to 256
n GND to V
CC Input/Reference Common Mode Range
n 2-Wire I2C Interface
n Programmable 50Hz, 60Hz or Simultaneous
50Hz/60Hz Rejection Mode
n 2ppm (0.25LSB) INL, No Missing Codes
n 1ppm Offset and 15ppm Full-Scale Error
n Selectable 2x Speed Mode
n No Latency: Digital Filter Settles in a Single Cycle
n Single Supply 2.7V to 5.5V Operation
n Internal Oscillator
n Six Addresses Available and One Global Address for
Synchronization
n Available in a Tiny (3mm × 3mm) 10-Lead DFN Package
n
Applications
Direct Sensor Digitizer
Weight Scales
n Direct Temperature Measurement
n Strain Gauge Transducers
n Instrumentation
n Industrial Process Control
n DVMs and Meters
n
n
LTC2481
16-Bit ∆Σ ADC with Easy Drive
Input Current Cancellation
and I2C Interface
Description
The LTC®2481 combines a 16-bit plus sign No Latency ∆Σ™
analog-to-digital converter with patented Easy Drive
technology and I2C digital interface. The patented sampling
scheme eliminates dynamic input current errors and the
shortcomings of on-chip buffering through automatic
cancellation of differential input current. This allows large
external source impedances and input signals, with rail-torail input range to be directly digitized while maintaining
exceptional DC accuracy.
The LTC2481 includes on-chip programmable gain and
an oscillator. The LTC2481 can be configured through an
I2C interface to provide a programmable gain from 1 to
256 in 8 steps, to digitize an external signal or internal
temperature sensor, reject line frequencies (50Hz, 60Hz or
simultaneous 50Hz/60Hz) as well as a 2x speed-up mode.
The LTC2481 allows a wide common mode input range
(0V to VCC) independent of the reference voltage. The
reference can be as low as 100mV or can be tied directly
to VCC. The LTC2481 includes an on-chip trimmed oscillator eliminating the need for external crystals or oscillators. Absolute accuracy and low drift are automatically
maintained through continuous, transparent, offset and
full-scale calibration.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
No Latency ∆∑ and Easy Drive are trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners. Patents Pending.
Typical Application
+FS Error vs RSOURCE at IN+ and IN–
80
VCC
10k
IDIFF = 0
VIN+
SENSE
REF+
VCC
LTC2481
10k
VIN–
0.1µF
GND
REF–
SCL
SDA
CA0/f0
CA1
2-WIRE
I2C INTERFACE
6 ADDRESSES
+FS ERROR (ppm)
1µF
0.1µF
VCC = 5V
= 5V
60 VREF
VIN+ = 3.75V
– = 1.25V
40 VIN
fO = GND
20 TA = 25°C
CIN = 1µF
0
–20
–40
2481 TA01a
–60
–80
1
10
100
1k
RSOURCE (Ω)
10k
100k
2481 TA01b
2481fd
For more information www.linear.com/LTC2481
1
LTC2481
Absolute Maximum Ratings
Pin Configuration
(Notes 1, 2)
TOP VIEW
Supply Voltage (VCC) to GND....................... – 0.3V to 6V
Analog Input Voltage to GND........ –0.3V to (VCC + 0.3V)
Reference Input Voltage to GND... –0.3V to (VCC + 0.3V)
Digital Input Voltage to GND........ – 0.3V to (VCC + 0.3V)
Digital Output Voltage to GND....... –0.3V to (VCC + 0.3V)
Operating Temperature Range
LTC2481C..................................................... 0°C to 70°C
LTC2481I ..................................................– 40°C to 85°C
LTC2481H............................................... –40°C to 125°C
Storage Temperature Range.................. –65°C to 125°C
REF+
1
VCC
2
10 CA0/f 0
9 CA1
REF –
3
IN+
4
7 SDA
IN–
5
6 SCL
11
8 GND
DD PACKAGE
10-LEAD (3mm × 3mm) PLASTIC DFN
TJMAX = 125°C, θJA = 43°C/W
EXPOSED PAD (PIN 11) IS GND, MUST BE SOLDERED TO PCB
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2481CDD#PBF
LTC2481CDD#TRPBF
LBPV
10-Lead (3mm × 3mm) Plastic DFN
0°C to 70°C
LTC2481IDD#PBF
LTC2481IDD#TRPBF
LBPV
10-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LTC2481HDD#PBF
LTC2481HDD#TRPBF
LBPV
10-Lead (3mm × 3mm) Plastic DFN
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
Electrical
Characteristics (Normal Speed) l denotes the specifications which
The
apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
Resolution (No Missing Codes)
0.1 ≤ VREF ≤ VCC, –FS ≤ VIN ≤ +FS (Note 5)
l
Integral Nonlinearity
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6)
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
l
2
1
10
ppm of VREF
ppm of VREF
Offset Error
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 13)
l
0.5
2.5
µV
Offset Error Drift
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF (H-Grade)
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN– = 0.75VREF, IN+ = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN– = 0.75VREF, IN+ = 0.25VREF (H-Grade)
2.5V ≤ VREF ≤ VCC, IN– = 0.75VREF, IN+ = 0.25VREF
25
40
ppm of VREF
ppm
Positive Full-Scale Error
Positive Full-Scale Error Drift
Negative Full-Scale Error
Negative Full-Scale Error Drift
MIN
TYP
MAX
16
UNITS
Bits
10
l
nV/°C
0.1
ppm of VREF /°C
25
40
l
ppm of VREF
ppm
0.1
ppm of VREF/°C
Total Unadjusted Error
5V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6)
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
15
15
15
ppm of VREF
ppm of VREF
ppm of VREF
Output Noise
5V ≤ VCC ≤ 5.5V, VREF = 5V, GND ≤ IN– = IN+ ≤ VCC (Note 12)
0.6
µVRMS
Internal PTAT Signal
TA = 27°C
Programmable Gain
See Table 2a
2
l
390
450
1
256
mV
2481fd
For more information www.linear.com/LTC2481
LTC2481
Electrical
Characteristics (2x Speed) l denotes the specifications which apply over
The
the full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
MIN
Resolution (No Missing Codes) 0.1 ≤ VREF ≤ VCC, –FS ≤ VIN ≤ +FS (Note 5)
Integral Nonlinearity
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6)
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
Offset Error
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 13)
Offset Error Drift
Output Noise
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN– = 0.75VREF, IN+ = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN– = 0.75VREF, IN+ = 0.25VREF
5V ≤ VCC ≤ 5.5V, VREF = 5V, GND ≤ IN– = IN+ ≤ VCC
Programmable Gain
See Table 2b
Positive Full-Scale Error
Positive Full-Scale Error Drift
Negative Full-Scale Error
Negative Full-Scale Error Drift
l
TYP
MAX
UNITS
16
Bits
l
2
1
10
ppm of VREF
l
0.5
2
mV
25
ppm of VREF
100
nV/°C
l
0.1
ppm of VREF/°C
25
l
ppm of VREF
0.1
ppm of VREF/°C
0.84
l
µVRMS
1
128
Converter
Characteristics l denotes the specifications which apply over the full operating
The
temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
Input Common Mode Rejection DC
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Note 5)
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Note 5)
Input Common Mode Rejection
50Hz ± 2%
MIN
TYP
MAX
UNITS
l
140
dB
l
140
dB
dB
Input Common Mode Rejection
60Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Note 5)
l
140
Input Normal Mode Rejection
50Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Notes 5, 7)
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (H-Grade)
l
l
110
104
120
dB
dB
Input Normal Mode Rejection
60Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Notes 5, 8)
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (H-Grade)
l
l
110
104
120
dB
dB
Input Normal Mode Rejection
50Hz/60Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Notes 5, 9)
l
87
Reference Common Mode Rejection DC
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Note 5)
l
120
Power Supply Rejection DC
Power Supply Rejection, 50Hz ±2%
Power Supply Rejection, 60Hz ±2%
dB
140
dB
VREF
= 2.5V, IN– = IN+ = GND
120
dB
VREF
= 2.5V, IN– = IN+ = GND (Notes 7, 9)
120
dB
VREF
= 2.5V, IN– = IN+ = GND (Notes 8, 9)
120
dB
Analog
Input and Reference l denotes the specifications which apply over the full operating
The
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
IN+
Absolute/Common Mode IN+ Voltage
CONDITIONS
MIN
TYP
MAX
UNITS
GND – 0.3V
VCC + 0.3V
V
IN–
Absolute/Common Mode IN– Voltage
GND – 0.3V
VCC + 0.3V
V
FS
Full Scale of the Differential Input (IN+ – IN–)
l
0.5VREF/GAIN
LSB
Least Significant Bit of the Output Code
l
FS/216
VIN
Input Differential Voltage Range (IN+ – IN–)
l
–FS
VREF
Reference Voltage Range (REF+ – REF–)
l
0.1
CS (IN+)
IN+ Sampling Capacitance
V
+FS
VCC
11
V
V
pF
2481fd
For more information www.linear.com/LTC2481
3
LTC2481
Analog
Input and Reference l denotes the specifications which apply over the full operating
The
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CS (IN–)
IN– Sampling Capacitance
CS (VREF)
CONDITIONS
MIN
TYP
VREF Sampling Capacitance
MAX
UNITS
11
pF
11
pF
(IN+)
IN+ DC Leakage Current
Sleep Mode, IN+ = GND
l
–10
1
10
nA
IDC_LEAK (IN–)
IN– DC Leakage Current
Sleep Mode, IN– = GND
l
–10
1
10
nA
IDC_LEAK (VREF)
REF+, REF– DC Leakage Current
Sleep Mode, VREF = VCC
l
–100
1
100
nA
IDC_LEAK
2C Digital Inputs and Digital Outputs
I The
l denotes the specifications which apply over
the full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VIH
High Level Input Voltage
l
VIL
Low Level Input Voltage
l
0.3VCC
V
VIL(CA1)
Low Level Input Voltage for Address Pin
l
0.05VCC
V
VIH(CA0/f0,CA1)
High Level Input Voltage for Address Pins
l
RINH
Resistance from CA0/f0, CA1 to VCC to Set
Chip Address Bit to 1
l
10
kΩ
RINL
Resistance from CA1 to GND to Set Chip
Address Bit to 0
l
10
kΩ
RINF
Resistance from CA0/f0, CA1 to VCC or
GND to Set Chip Address Bit to Float
l
II
Digital Input Current
l
VHYS
Hysteresis of Schmitt Trigger Inputs
(Note 5)
VOL
Low Level Output Voltage SDA
I = 3mA
l
tOF
Output Fall Time from VIHMIN to VILMAX
Bus Load CB 10pF to 400pF (Note 14)
l
tSP
Input Spike Suppression
IIN
Input Leakage
CI
Capacitance for Each I/O Pin
l
CB
Capacitance Load for Each Bus Line
l
400
pF
CCAX
External Capacitive Load On-Chip Address
Pins (CA0/f 0,CA1) for Valid Float
l
10
pF
VIH(EXT,OSC)
High Level CA0/f0 External Oscillator
2.7V ≤ VCC < 5.5V
l
VIL(EXT,OSC)
Low Level CA0/f0 External Oscillator
2.7V ≤ VCC < 5.5V
l
0.5
V
0.7VCC
V
0.95VCC
V
2
MΩ
–10
10
µA
0.05VCC
0.4
20+0.1CB
l
0.1VCC ≤ VIN ≤ VCC
V
V
250
ns
50
ns
1
µA
l
10
pF
VCC – 0.5V
V
Power
Requirements l denotes the specifications which apply over the full operating temperature
The
range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
VCC
Supply Voltage
ICC
Supply Current
4
CONDITIONS
MIN
l
Conversion Mode (Note 11)
Sleep Mode (Note 11)
H-Grade
l
l
l
TYP
MAX
5.5
V
160
1
250
2
20
µA
µA
µA
2.7
UNITS
2481fd
For more information www.linear.com/LTC2481
LTC2481
Timing
Characteristics l denotes the specifications which apply over the full operating temperature
The
range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
MAX
UNITS
fEOSC
External Oscillator Frequency Range
CONDITIONS
l
MIN
10
TYP
1000
kHz
tHEO
External Oscillator High Period
l
0.125
100
µs
tLEO
External Oscillator Low Period
l
0.125
100
µs
tCONV_1
Conversion Time for 1x Speed Mode
50Hz Mode
50Hz Mode (H-Grade)
60Hz Mode
60Hz Mode (H-Grade)
Simultaneous 50Hz/60Hz Mode
Simultaneous 50Hz/60Hz Mode (H-Grade)
External Oscillator (Note 10)
l
l
l
l
l
l
l
157.2
157.2
131.0
131.0
144.1
144.1
160.3
160.3
133.6
133.6
146.9
146.9
41036/fEOSC
163.5
165.1
136.3
137.6
149.9
151.0
ms
ms
ms
ms
ms
ms
ms
tCONV_2
Conversion Time for 2x Speed Mode
50Hz Mode
50Hz Mode (H-Grade)
60Hz Mode
60Hz Mode (H-Grade)
Simultaneous 50Hz/60Hz Mode
Simultaneous 50Hz/60Hz Mode (H-Grade)
External Oscillator (Note 10)
l
l
l
l
l
l
l
78.7
80.3
65.6
66.9
72.2
73.6
81.9
82.7
68.2
68.9
75.1
75.6
ms
ms
ms
ms
ms
ms
ms
20556/fEOSC
2C Timing Characteristics
I The
l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 15)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
fSCL
SCL Clock Frequency
l
0
tHD(SDA)
Hold Time (Repeated) START Condition
l
0.6
400
kHz
µs
tLOW
LOW Period of the SCL Clock Pin
l
1.3
µs
tHIGH
HIGH Period of the SCL Clock Pin
l
0.6
µs
tSU(STA)
Set-Up Time for a Repeated START Condition
l
0.6
µs
tHD(DAT)
Data Hold Time
l
0
tSU(DAT)
Data Set-Up Time
l
100
tr
Rise Time for Both SDA and SCL Signals
(Note 14)
l
20+0.1CB
300
ns
tf
Fall Time for Both SDA and SCL Signals
(Note 14)
l
20+0.1CB
300
ns
tSU(STO)
Set-Up Time for STOP Condition
l
0.6
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to GND.
Note 3: VCC = 2.7V to 5.5V unless otherwise specified.
VREF = REF+ – REF–, VREFCM = (REF+ + REF–)/2, FS = 0.5VREF/GAIN;
VIN = IN+ – IN–, VINCM = (IN+ + IN–)/2.
Note 4: Use internal conversion clock or external conversion clock source
with fEOSC = 307.2kHz unless otherwise specified.
Note 5: Guaranteed by design, not subject to test.
Note 6: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
0.9
µs
ns
µs
Note 7: 50Hz mode (internal oscillator) or fEOSC = 256kHz ±2% (external
oscillator).
Note 8: 60Hz mode (internal oscillator) or fEOSC = 307.2kHz ±2% (external
oscillator).
Note 9: Simultaneous 50Hz/60Hz mode (internal oscillator) or fEOSC =
280kHz ±2% (external oscillator).
Note 10: The external oscillator is connected to the CA0/f0 pin. The
external oscillator frequency, fEOSC, is expressed in kHz.
Note 11: The converter uses the internal oscillator.
Note 12: The output noise includes the contribution of the internal
calibration operations.
Note 13: Guaranteed by design and test correlation.
Note 14: CB = capacitance of one bus line in pF.
Note 15: All values refer to VIH(MIN) and VIL(MAX) levels.
2481fd
For more information www.linear.com/LTC2481
5
LTC2481
Typical Performance Characteristics
Integral Nonlinearity
(VCC = 5V, VREF = 2.5V)
–45°C
25°C
0
85°C
–1
–2
1
–45°C, 25°C, 90°C
0
–1
2
–3
–1.25
2.5
–0.75
4
0
Total Unadjusted Error
(VCC = 5V, VREF = 2.5V)
12
25°C
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
8
85°C
12
85°C
–4
4
–45°C
0
–4
2
–12
–1.25
2.5
–0.75
12
12
0
1.8
–0.25
0.25
0.75
INPUT VOLTAGE (V)
–3 –2.4 –1.8 –1.2 –0.6 0 0.6
OUTPUT READING (µV)
1.25
2481 G06
VCC = 5V, VREF = 5V, VIN = 0V, VIN(CM) = 2.5V
4 GAIN = 256, TA = 25°C, RMS NOISE = 0.60µV
3
4
0
1.2
–0.75
Long-Term ADC Readings
6
2
2481 G07
6
–4
5
10,000 CONSECUTIVE
READINGS
RMS = 0.59µV
VCC = 2.7V
AVERAGE = –0.19µV
VREF = 2.5V
10 VIN = 0V
GAIN = 256
8 TA = 25°C
2
–3 –2.4 –1.8 –1.2 –0.6 0 0.6
OUTPUT READING (µV)
85°C
–45°C
0
Noise Histogram (7.5sps)
14
NUMBER OF READINGS (%)
NUMBER OF READINGS (%)
Noise Histogram (6.8sps)
4
25°C
4
2481 G05
14
6
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
–12
–1.25
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
2481 G04
10,000 CONSECUTIVE
READINGS
RMS = 0.60µV
VCC = 5V
AVERAGE = –0.69µV
VREF = 5V
10 VIN = 0V
GAIN = 256
8 TA = 25°C
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
–8
–8
–8
–12
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
–0.75
Total Unadjusted Error
(VCC = 2.7V, VREF = 2.5V)
8
25°C
–45°C
–1
2481 G03
TUE (ppm OF VREF)
TUE (ppm OF VREF)
8
0
2481 G02
Total Unadjusted Error
(VCC = 5V, VREF = 5V)
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
–45°C, 25°C, 90°C
–3
–1.25
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
2481 G01
12
1
–2
–2
–3
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
2
TUE (ppm OF VREF)
1
2
3
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
ADC READING (µV)
INL (ppm OF VREF)
2
3
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
INL (ppm OF VREF)
3
Integral Nonlinearity
(VCC = 2.7V, VREF = 2.5V)
INL (ppm OF VREF)
Integral Nonlinearity
(VCC = 5V, VREF = 5V)
2
1
0
–1
–2
–3
–4
1.2
1.8
2481 G08
–5
0
10
30
40
20
TIME (HOURS)
50
60
2481 G09
2481fd
For more information www.linear.com/LTC2481
LTC2481
Typical Performance Characteristics
RMS Noise
vs Input Differential Voltage
RMS NOISE (ppm OF VREF)
0.9
RMS Noise vs VIN(CM)
1.0
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
GAIN = 256
TA = 25°C
0.9
0.8
RMS NOISE (µV)
0.8
0.7
0.6
RMS Noise vs Temperature (TA)
1.0
0.7
0.6
0.4
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5 2
INPUT DIFFERENTIAL VOLTAGE (V)
0.4
2.5
–1
0
2
1
3
5
4
RMS Noise vs VREF
0.6
0.8
0.7
0.6
0.5
0.5
3.1
3.5
3.9 4.3
VCC (V)
4.7
5.1
0.4
5.5
0
1
2
3
VREF (V)
4
OFFSET ERROR (ppm OF VREF)
OFFSET ERROR (ppm OF VREF)
0.2
0.3
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
0.1
0
–0.1
–0.2
–0.3
–45 –30 –15
0 15 30 45 60
TEMPERATURE (°C)
75
90
2481 G16
5
0.2
0.1
0
–0.1
–0.2
–0.3
–1
0
1
3
2
VIN(CM) (V)
5
4
0.2
0.1
Offset Error vs VCC
Offset Error vs VREF
0.3
REF+ = 2.5V
– = GND
REF
VIN = 0V
VIN(CM) = GND
TA = 25°C
0
–0.1
VCC = 5V
REF– = GND
VIN = 0V
VIN(CM) = GND
TA = 25°C
0.2
0.1
0
–0.1
–0.2
–0.3
2.7
6
2481 G15
OFFSET ERROR (ppm OF VREF)
Offset Error vs Temperature
90
VCC = 5V
VREF = 5V
VIN = 0V
TA = 25°C
2481 G14
2481 G13
0.3
75
Offset Error vs VIN(CM)
0.3
VCC = 5V
VIN = 0V
VIN(CM) = GND
GAIN = 256
TA = 25°C
0.9
0.7
0 15 30 45 60
TEMPERATURE (°C)
2481 G12
OFFSET ERROR (ppm OF VREF)
1.0
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
GAIN = 256
TA = 25°C
0.4
2.7
0.4
–45 –30 –15
6
2481 G11
RMS NOISE (µV)
RMS NOISE (µV)
0.8
0.6
VIN(CM) (V)
RMS Noise vs VCC
0.9
0.7
0.5
2481 G10
1.0
0.8
0.5
0.5
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
GAIN = 256
0.9
RMS NOISE (µV)
1.0
–0.2
3.1
3.5
3.9 4.3
VCC (V)
4.7
5.1
5.5
2481 G17
–0.3
0
1
2
3
VREF (V)
4
5
2481 G18
2481fd
For more information www.linear.com/LTC2481
7
LTC2481
Typical Performance Characteristics
On-Chip Oscillator Frequency
vs Temperature
310
310
304
VCC = 4.1V
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
300
–45 –30 –15
–40
306
304
75
300
90
2.5
3.0
3.5
4.0
VCC (V)
5.0
4.5
–60
–80
–100
–120
–120
–140
30600
30650
30700
30800
30750
FREQUENCY AT VCC (Hz)
Sleep Mode Current
vs Temperature
1.6
SUPPLY CURRENT (µA)
SLEEP MODE CURRENT (µA)
140
VCC = 2.7V
120
100
–45 –30 –15
0 15 30 45 60
TEMPERATURE (°C)
75
90
2481 G26
VREF = VCC
IN+ = GND
IN– = GND
400 CA0/f0 = EXT OSC
TA = 25°C
450
1.4
VCC = 5V
1.0
0.8
VCC = 2.7V
0.4
350
300
250
VCC = 5V
200
150
0.2
0 15 30 45 60
TEMPERATURE (°C)
75
90
100
VCC = 3V
0
10
20
OUTPUT DATA RATE (READINGS/SEC)
2481 G27
8
160
500
1.8
0
–45 –30 –15
VCC = 5V
Conversion Current
vs Output Data Rate
2.0
0.6
1M
180
2481 G25
2481 G24
1.2
10k 100k
1k
100
FREQUENCY AT VCC (Hz)
200
VCC = 4.1V DC ±0.7V
= 2.5V
V
–20 INREF
+ = GND
– = GND
IN
–40 TA = 25°C
–100
0 20 40 60 80 100 120 140 160 180 200 220
FREQUENCY AT VCC (Hz)
10
Conversion Current
vs Temperature
CONVERSION CURRENT (µA)
–80
1
2481 G23
0
VCC = 4.1V DC ±1.4V
VREF = 2.5V
IN+ = GND
IN– = GND
TA = 25°C
–60
–140
–140
PSRR vs Frequency at VCC
REJECTION (dB)
REJECTION (dB)
–40
5.5
2481 G22
PSRR vs Frequency at VCC
–20
–80
–120
2481 G21
0
–60
–100
302
0 15 30 45 60
TEMPERATURE (°C)
VCC = 4.1V DC
VREF = 2.5V
IN+ = GND
IN– = GND
TA = 25°C
–20
REJECTION (dB)
306
PSRR vs Frequency at VCC
0
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
308
FREQUENCY (kHz)
FREQUENCY (kHz)
308
302
On-Chip Oscillator Frequency
vs VCC
30
2481 G28
2481fd
For more information www.linear.com/LTC2481
LTC2481
Typical Performance Characteristics
3
3
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
1
25°C, 90°C
0
–1
–45°C
–2
–3
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
1
90°C
0
–45°C, 25°C
–1
–3
–1.25
2.5
–0.75
–0.25
0.25
0.75
INPUT VOLTAGE (V)
198
0.8
196
0.6
0.4
VCC = 5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
0.2
188.6
186.2
OUTPUT READING (µV)
0
1
0
3
2
VREF (V)
4
192
190
188
186
180
5
–1
0
3
2
VIN(CM) (V)
1
2481 G33
4
5
6
2481 G34
Offset Error vs VCC
(2x Speed Mode)
250
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
200
OFFSET ERROR (µV)
220
194
VCC = 5V
VREF = 5V
VIN = 0V
TA = 25°C
182
Offset Error vs Temperature
(2x Speed Mode)
230
1.25
184
2481 G32
240
–0.25
0.25
0.75
INPUT VOLTAGE (V)
Offset Error vs VIN(CM)
(2x Speed Mode)
200
2
183.8
–0.75
2481 G31
OFFSET ERROR (µV)
4
–45°C, 25°C
–1
–3
–1.25
1.25
1.0
RMS NOISE (µV)
6
OFFSET ERROR (µV)
NUMBER OF READINGS (%)
8
90°C
0
RMS Noise vs VREF
(2x Speed Mode)
16
181.4
1
2481 G30
Noise Histogram
(2x Speed Mode)
RMS = 0.86µV
10,000 CONSECUTIVE
AVERAGE = 0.184mV
14 READINGS
VCC = 5V
12 VREF = 5V
VIN = 0V
GAIN = 256
10
TA = 25°C
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
–2
–2
2
Integral Nonlinearity (2x Speed
Mode; VCC = 2.7V, VREF = 2.5V)
2
2481 G29
0
179
3
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
2
INL (ppm OF VREF)
2
INL (ppm OF VREF)
Integral Nonlinearity (2x Speed
Mode; VCC = 5V, VREF = 2.5V)
INL (ppm OF VREF)
Integral Nonlinearity (2x Speed
Mode; VCC = 5V, VREF = 5V)
210
200
190
180
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
150
100
50
170
160
–45 –30 –15
0 15 30 45 60
TEMPERATURE (°C)
75
90
0
2.7 3
2481 G35
3.5
4
4.5
VCC (V)
5
5.5
2481 G36
2481fd
For more information www.linear.com/LTC2481
9
LTC2481
Typical Performance Characteristics
PSRR vs Frequency at VCC
(2x Speed Mode)
Offset Error vs VREF
(2x Speed Mode)
240
230
220
–40
210
200
190
–60
–80
–100
180
–120
170
160
VCC = 4.1V DC
REF+ = 2.5V
REF– = GND
IN+ = GND
IN– = GND
TA = 25°C
–20
REJECTION (dB)
OFFSET ERROR (µV)
0
VCC = 5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
1
0
2
4
3
VREF (V)
5
–140
1
10k 100k
1k
100
FREQUENCY AT VCC (Hz)
10
2481 G38
2481 G37
PSRR vs Frequency at VCC
(2x Speed Mode)
RREJECTION (dB)
–20
–40
PSRR vs Frequency at VCC
(2x Speed Mode)
0
VCC = 4.1V DC ±1.4V
REF+ = 2.5V
REF– = GND
IN+ = GND
IN– = GND
TA = 25°C
VCC = 4.1V DC ±0.7V
REF+ = 2.5V
REF– = GND
IN+ = GND
–40 IN– = GND
TA = 25°C
–20
REJECTION (dB)
0
–60
–80
–60
–80
–100
–100
–120
–120
–140
1M
0 20 40 60 80 100 120 140 160 180 200 220
FREQUENCY AT VCC (Hz)
–140
30600
30650
30700
30750
FREQUENCY AT VCC (Hz)
30800
2481 G40
2481 G39
Pin Functions
REF+ (Pin 1), REF– (Pin 3): Differential Reference Input.
The voltage on these pins can have any value between
GND and VCC as long as the reference positive input,
REF+, is more positive than the reference negative input,
REF –, by at least 0.1V.
VCC (Pin 2): Positive Supply Voltage. Bypass to GND
(Pin 8) with a 1µF tantalum capacitor in parallel with 0.1µF
ceramic capacitor as close to the part as possible.
10
IN+ (Pin 4), IN– (Pin 5): Differential Analog Input. The
voltage on these pins can have any value between GND
– 0.3V and VCC + 0.3V. Within these limits the converter
bipolar input range (VIN = IN+ – IN–) extends from –0.5
• VREF /GAIN to 0.5 • VREF/GAIN. Outside this input
range the converter produces unique overrange and
underrange output codes.
2481fd
For more information www.linear.com/LTC2481
LTC2481
Pin Functions
SCL (Pin 6): Serial Clock Pin of the I2C Interface. The
LTC2481 can only act as a slave and the SCL pin only accepts external serial clock. Data is shifted into the SDA pin
on the rising edges of the SCL clock and output through
the SDA pin on the falling edges of the SCL clock.
SDA (Pin 7): Bidirectional Serial Data Line of the I2C Interface. In the transmitter mode (Read), the conversion result
is output through the SDA pin, while in the receiver mode
(Write), the device configuration bits are input through the
SDA pin. At data input mode, the pin is high impedance;
while at data output mode, it is an open-drain N-channel
driver and therefore an external pull-up resistor or current
source to VCC is needed.
GND (Pin 8): Ground. Connect this pin to a ground plane
through a low impedance connection.
CA1 (Pin 9): Chip Address Control Pin. The CA1 pin is
configured as a three state (LOW, HIGH, or Floating) address control bit for the device I2C address.
CA0/f0 (Pin 10): Chip Address Control Pin/External Clock
Input Pin. When no transition is detected on the CA0/f0
pin, it is a two state (HIGH or Floating) address control
bit for the device I2C address. When the pin is driven by
an external clock signal with a frequency fEOSC of at least
10kHz, the converter uses this signal as its system clock
and the fundamental digital filter rejection null is located
at a frequency fEOSC/5120 and sets the Chip Address CA0
internally to a HIGH.
Functional Block Diagram
2
1
4
5
REF+
VCC
IN+
IN+
IN–
SCL
REF+
I2C
SERIAL
INTERFACE
3RD ORDER
∆Σ ADC
(1-256)
IN–
REF–
GAIN
MUX
TEMP
SENSOR
SDA
CA1
CA0/f 0
6
7
9
10
AUTOCALIBRATION
AND CONTROL
REF–
3
GND
8
INTERNAL
OSCILLATOR
2481 FD
2481fd
For more information www.linear.com/LTC2481
11
LTC2481
Applications Information
Converter Operation
Converter Operation Cycle
The LTC2481 is a low power, ∆Σ analog-to-digital converter
with an I2C interface. After power on reset, its operation
is made up of three states. The converter operating cycle
begins with the conversion, followed by the low power sleep
state and ends with the data output/input (see Figure 1).
POWER ON RESET
DEFAULT CONFIGURATION:
EXTERNAL INPUT GAIN = 1
50/60Hz REJECTION
1X SPEED, AUTOCAL
CONVERSION
The device will not acknowledge an external request during
the conversion state. After a conversion is finished, the
device is ready to accept a read/write request. Once the
LTC2481 is addressed for a read operation, the device begins
outputting the conversion result under control of the serial
clock (SCL). There is no latency in the conversion result.
The data output is 24 bits long and contains a 16-bit plus
sign conversion result plus a readback of the configuration
bits corresponds to the conversion just performed. This
result is shifted out on the SDA pin under the control of the
SCL. Data is updated on the falling edges of SCL allowing
the user to reliably latch data on the rising edge of SCL.
In write operation, the device accepts one configuration
byte and the data is shifted in on the rising edges of the
SCL. A new conversion is initiated by a STOP condition
following a valid write operation or at the conclusion of a
data read operation (read out all 24 bits).
SLEEP
I2C INTERFACE
NO
The LTC2481 communicates through an I2C interface. The
I2C interface is a 2-wire open-drain interface supporting
multiple devices and masters on a single bus. The
connected devices can only pull the bus wires LOW and
can never drive the bus HIGH. The bus wires are externally
connected to a positive supply voltage via a currentsource or pull-up resistor. When the bus is free, both
lines are HIGH. Data on the I2C-bus can be transferred
at rates of up to 100kbit/s in the Standard-mode and up
to 400kbit/s in the Fast-mode. The VCC power should not
be removed from the device when the I2C bus is active to
avoid loading the I2C bus lines through the internal ESD
protection diodes.
ACKNOWLEDGE
YES
DATA OUTPUT/INPUT
NO
STOP
OR READ
24-BITS
YES
2481 F01
Figure 1. LTC2481 State Transition Diagram
Initially, the LTC2481 performs a conversion. Once the
conversion is complete, the device enters the sleep state.
While in this sleep state, power consumption is reduced
by two orders of magnitude. The part remains in the sleep
state as long as it is not addressed for a read/write operation. The conversion result is held indefinitely in a static
shift register while the converter is in the sleep state.
12
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate as either
a transmitter or receiver, depending on the function of
the device. In addition to transmitters and receivers,
devices can also be considered as masters or slaves when
performing data transfers. A master is the device which
initiates a data transfer on the bus and generates the clock
signals to permit that transfer. At the same time any device
addressed is considered a slave.
2481fd
For more information www.linear.com/LTC2481
LTC2481
Applications Information
The LTC2481 can only be addressed as a slave. Once
addressed, it can receive configuration bits or transmit the
last conversion result. Therefore the serial clock line SCL
is an input only and the data line SDA is bidirectional. The
device supports the Standard-mode and the Fast-mode
for data transfer speeds up to 400kbit/s. Figure 2 shows
the definition of timing for Fast/Standard-mode devices
on the I2C-bus.
The START and STOP Conditions
A START condition is generated by transitioning SDA from
HIGH to LOW while SCL is HIGH. The bus is considered to
be busy after the START condition. When the data transfer
is finished, a STOP condition is generated by transitioning
SDA from LOW to HIGH while SCL is HIGH. The bus is free
again a certain time after the STOP condition. START and
STOP conditions are always generated by the master.
When the bus is in use, it stays busy if a repeated START
(Sr) is generated instead of a STOP condition. The repeated
START (Sr) conditions are functionally identical to the
START (S).
Data Transferring
After the START condition, the I2C bus is busy and data
transfer is set between a master and a slave. Data is
transferred over I2C in groups of nine bits (one byte) followed
by an acknowledge bit, therefore each group takes nine
SCL cycles. The transmitter releases the SDA line during
the acknowledge clock pulse and the receiver issues an
Acknowledge (ACK) by pulling SDA LOW or leaves SDA
HIGH to indicate a Not Acknowledge (NACK) condition.
Change of data state can only happen while SCL is LOW.
Accessing the Special Features of the LTC2481
The LTC2481 combines a high resolution, low noise ∆Σ
analog-to-digital converter with an on-chip selectable
temperature sensor, programmable gain, programmable
digital filter and output rate control. These special features
are selected through a single 8-bit serial input word during
the data input/output cycle (see Figure 3).
The LTC2481 powers up in a default mode commonly
used for most measurements. The device will remain in
this mode until a valid write cycle is performed. In this
default mode, the measured input is external, the GAIN is 1,
the digital filter simultaneously rejects 50Hz and 60Hz
line frequency noise, and the speed mode is 1x (offset
automatically, continuously calibrated).
The I2C serial interface grants access to any or all special
functions contained within the LTC2481. In order to change
the mode of operation, a valid write address followed by 8
bits of data are shifted into the device (see Table 1). The first
3 bits (GS2, GS1, GS0) control the GAIN of the converter
from 1 to 256. The 4th bit is reserved and should be low.
The 5th bit (IM) is used to select the internal temperature
sensor as the conversion input, while the 6th and 7th bits
(FA, FB) combine to determine the line frequency rejection
mode. The 8th bit (SPD) is used to double the output rate
by disabling the offset auto calibration.
SDA
tLOW
tf
tSU;DAT
tr
tr
tHD;STA
tSP
tr
tBUF
SCL
S
tHD;STA
tHD;DAT
tHIGH
tSU;STA
Sr
tSU;STO
P
S
2481 F02
Figure 2. Definition of Timing for F/S-Mode Devices on the I2C-Bus
2481fd
For more information www.linear.com/LTC2481
13
LTC2481
Applications Information
1
2
…
7
8
9
1
2
3
GS2
GS1
GS0
4
5
6
7
8
IM
FA
FB
SPD
9
SCL
7-BIT ADDRESS
SDA
W
ACK BY
LTC2481
ACK BY
LTC2481
START BY
MASTER
SLEEP
DATA INPUT
2481 F03
Figure 3. Timing Diagram for Writing to the LTC2481
Table 1. Selecting Special Modes
Rejection
Mode
Gain
GS2 GS1 GS0 IM FA
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Any Gain
X
X
X
X
X
X
X
X
X
X
X
X
FB
SPD
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Any
0
0
Rejection
1
0
Mode
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
0
0
0
1
0
Any
1
0 Speed
0
1
1
0
1
0
0
X
1
0
1
X
1
1
0
X
1
1
1
X
2481 TBL1
14
Comments
External Input, Gain = 1, Autocalibration
External Input, Gain = 4, Autocalibration
External Input, Gain = 8, Autocalibration
External Input, Gain = 16, Autocalibration
External Input, Gain = 32, Autocalibration
External Input, Gain = 64, Autocalibration
External Input, Gain = 128, Autocalibration
External Input, Gain = 256, Autocalibration
External Input, Gain = 1, 2x Speed
External Input, Gain = 2, 2x Speed
External Input, Gain = 4, 2x Speed
External Input, Gain = 8, 2x Speed
External Input, Gain = 16, 2x Speed
External Input, Gain = 32, 2x Speed
External Input, Gain = 64, 2x Speed
External Input, Gain = 128, 2x Speed
External Input, Simultaneous 50Hz/60Hz Rejection
External Input, 50Hz Rejection
External Input, 60Hz Rejection
Reserved, Do Not Use
Temperature Input, 50Hz/60Hz Rejection, Gain = 1, Autocalibration
Temperature Input, 50Hz Rejection, Gain = 1, Autocalibration
Temperature Input, 60Hz Rejection, Gain = 1, Autocalibration
Reserved, Do Not Use
2481fd
For more information www.linear.com/LTC2481
LTC2481
Applications Information
Table 2a. The LTC2481 Performance vs GAIN in Normal Speed Mode (VCC = 5V, VREF = 5V)
GAIN
Input Span
LSB
Noise Free Resolution*
1
4
8
16
32
64
128
256
±2.5
±0.625
±0.312
±0.156
±78m
±39m
±19.5m
±9.76m
UNIT
V
38.1
9.54
4.77
2.38
1.19
0.596
0.298
0.149
µV
65536
65536
65536
65536
65536
65536
32768
16384
Counts
Gain Error
5
5
5
5
5
5
5
8
Offset Error
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ppm of FS
µV
UNIT
Table 2b. The LTC2481 Performance vs GAIN in 2x Speed Mode (VCC = 5V, VREF = 5V)
1
2
4
8
16
32
64
128
Input Span
GAIN
±2.5
±1.25
±0.625
±0.312
±0.156
±78m
±39m
±19.5m
V
LSB
38.1
19.1
9.54
4.77
2.38
1.19
0.596
0.298
µV
65536
65536
65536
65536
65536
65536
45875
22937
Gain Error
Noise Free Resolution*
5
5
5
5
5
5
5
5
Offset Error
200
200
200
200
200
200
200
200
Counts
ppm of FS
µV
*The resolution in counts is calculated as the FS divided by LSB or the RMS noise value, whichever is larger.
GAIN (GS2, GS1, GS0)
Rejection Mode (FA, FB)
The input referred gain of the LTC2481 is adjustable from
1 to 256. With a gain of 1, the differential input range is
±VREF/2 and the common mode input range is rail-to-rail.
As the GAIN is increased, the differential input range is reduced to ±VREF/2 • GAIN but the common mode input range
remains rail-to-rail. As the differential gain is increased,
low level voltages are digitized with greater resolution. At
a gain of 256, the LTC2481 digitizes an input signal range
of ±9.76mV with over 16,000 counts.
The LTC2481 includes a high accuracy on-chip oscillator with no required external components. Coupled with
a 4th order digital lowpass filter, the LTC2481 rejects
line frequency noise. In the default mode, the LTC2481
simultaneously rejects 50Hz and 60Hz by at least 87dB.
The LTC2481 can also be configured to selectively reject
50Hz or 60Hz to better than 110dB.
Temperature Sensor (IM)
The LTC2481 includes an on-chip temperature sensor.
The temperature sensor is selected by setting IM = 1 in
the serial input data stream. Conversions are performed
directly on the temperature sensor by the converter. While
operating in this mode, the device behaves as a temperature
to bits converter. The digital reading is proportional to
the absolute temperature of the device. This feature
allows the converter to linearize temperature sensors or
continuously remove temperature effects from external
sensors. Several applications leveraging this feature are
presented in more detail in the applications section. While
operating in this mode, the gain is set to 1 and the speed
is set to normal independent of the control bits (GS2,
GS1, GS0 and SPD).
Speed Mode (SPD)
The LTC2481 continuously performs offset calibrations.
Every conversion cycle, two conversions are automatically
performed (default) and the results combined. This result
is free from offset and drift. In applications where the offset
is not critical, the autocalibration feature can be disabled
with the benefit of twice the output rate.
Linearity, full-scale accuracy and full-scale drift are identical for both 2x and 1x speed modes. In both the 1x and
2x speed there is no latency. This enables input steps or
multiplexer channel changes to settle in a single conversion cycle easing system overhead and increasing the
effective conversion rate.
2481fd
For more information www.linear.com/LTC2481
15
LTC2481
Applications Information
LTC2481 Data Format
After a START condition, the master sends a 7-bit address
followed by a R/W bit. The bit R/W is 1 for a Read request
and 0 for a Write request. If the 7-bit address agrees with
an LTC2481’s address, that device is selected. When the
device is in the conversion state, it does not accept the
request and issues a Not-Acknowledge (NACK) by leaving
SDA HIGH. If the conversion is complete, it issues an
acknowledge (ACK) by pulling SDA LOW.
The LTC2481 has two registers. The output register contains
the result of the last conversion and a user programmable
configuration register that sets the converter operation
mode.
The output register contains the last conversion result. After
each conversion is completed, the device automatically
enters the sleep state where the supply current is reduced
to 1µA. When the LTC2481 is addressed for a Read
operation, it acknowledges (by pulling SDA LOW) and
acts as a transmitter. The master and receiver can read up
to three bytes from the LTC2481. After a complete Read
operation (3 bytes), the output register is emptied, a new
conversion is initiated, and a following Read request in the
same input/output phase will be NACKed. The LTC2481
output data stream is 24 bits long, shifted out on the falling
edges of SCL. The first bit is the conversion result sign bit
(SIG), see Tables 3 and 4. This bit is HIGH if VIN ≥ 0. It is
LOW if VIN 1nF at Both IN+
Constant
VIN(CM) – VREF(CM) and IN–. Can Take Large
Source Resistance with
Negligible Error
CEXT > 1nF at Both IN+
and IN–. Can Take Large
Source Resistance.
Unbalanced Resistance
Results in an Offset Which
Can be Calibrated
Varying
CEXT > 1nF at Both IN+
VIN(CM) – VREF(CM) and IN–. Can Take Large
Source Resistance with
Negligible Error
Minimize IN+ and
IN– Capacitors and Avoid
Large Source Impedance
(< 5k Recommended)
The magnitude of the dynamic input current depends upon
the size of the very stable internal sampling capacitors and
upon the accuracy of the converter sampling clock. The
accuracy of the internal clock over the entire temperature
and power supply range is typically better than 0.5%. Such
24
a specification can also be easily achieved by an external
clock. When relatively stable resistors (50ppm/°C) are
used for the external source impedance seen by IN+ and
IN–, the expected drift of the dynamic current and offset
will be insignificant (about 1% of their respective values
over the entire temperature and voltage range). Even for
the most stringent applications, a one-time calibration
operation may be sufficient.
In addition to the input sampling charge, the input ESD
protection diodes have a temperature dependent leakage
current. This current, nominally 1nA (±10nA max), results
in a small offset shift. A 1k source resistance will create a
1µV typical and 10µV maximum offset voltage.
Reference Current
In a similar fashion, the LTC2481 samples the differential
reference pins REF+ and REF– transferring small amount
of charge to and from the external driving circuits thus
producing a dynamic reference current. This current does
not change the converter offset, but it may degrade the
gain and INL performance. The effect of this current can
be analyzed in two distinct situations.
For relatively small values of the external reference capacitors (CREF < 1nF), the voltage on the sampling capacitor
settles almost completely and relatively large values for
the source impedance result in only small errors. Such
values for CREF will deteriorate the converter offset and
gain performance without significant benefits of reference
filtering and the user is advised to avoid them.
Larger values of reference capacitors (CREF > 1nF) may be
required as reference filters in certain configurations. Such
capacitors will average the reference sampling charge and
the external source resistance will see a quasi constant
reference differential impedance.
In the following discussion, it is assumed the input and
reference common mode are the same. Using internal
oscillator for 60Hz mode, the typical differential reference
resistance is 1MΩ which generates a full-scale (VREF/2) gain
error of 0.51ppm for each ohm of source resistance driving
the REF+ and REF– pins. For 50Hz/60Hz mode, the related
difference resistance is 1.1MΩ and the resulting full-scale
error is 0.46ppm for each ohm of source resistance driving
2481fd
For more information www.linear.com/LTC2481
LTC2481
Applications Information
the REF+ and REF– pins. For 50Hz mode, the related difference resistance is 1.2MΩ and the resulting full-scale error
is 0.42ppm for each ohm of source resistance driving the
REF+ and REF– pins. When CA0/f0 is driven by an external
oscillator with a frequency fEOSC (external conversion clock
operation), the typical differential reference resistance is
0.30 • 1012/fEOSC Ω and each ohm of source resistance
driving the REF+ or REF– pins will result in 1.67 • 10–6 •
fEOSCppm gain error. The typical +FS and –FS errors for
various combinations of source resistance seen by the
REF+ or REF– pins and external capacitance connected to
that pin are shown in Figures 16-19.
In addition to this gain error, the converter INL performance is degraded by the reference source impedance. The INL is caused by the input dependent terms
–VIN2/(VREF • REQ) – (0.5 • VREF • DT)/REQ in the reference
90
60
50
CREF = 0.01µF
CREF = 0.001µF
CREF = 100pF
CREF = 0pF
40
30
20
VCC = 5V
VREF = 5V
VIN+ = 3.75V
VIN– = 1.25V
TA = 25°C
400
+FS ERROR (ppm)
70
+FS ERROR (ppm)
500
VCC = 5V
VREF = 5V
VIN+ = 3.75V
VIN– = 1.25V
TA = 25°C
80
pin current as expressed in Figure 12. When using internal
oscillator and 60Hz mode, every 100Ω of reference source
resistance translates into about 0.67ppm additional INL
error. When using internal oscillator and 50Hz/60Hz mode,
every 100Ω of reference source resistance translates into
about 0.61ppm additional INL error. When using internal
oscillator and 50Hz mode, every 100Ω of reference source
resistance translates into about 0.56ppm additional INL
error. When CA0/f0 is driven by an external oscillator
with a frequency fEOSC, every 100Ω of source resistance
driving REF+ or REF– translates into about 2.18 • 10–6 •
fEOSCppm additional INL error. Figure 20 shows the typical
INL error due to the source resistance driving the REF+
or REF– pins when large CREF values are used. The user
is advised to minimize the source impedance driving the
REF+ and REF– pins.
CREF = 1µF, 10µF
CREF = 0.1µF
300
200
CREF = 0.01µF
100
10
0
–10
0
10
1k
100
RSOURCE (Ω)
10k
0
100k
200
0
2481 F16
Figure 16. +FS Error vs RSOURCE at REF+ or REF– (Small CREF)
600
400
RSOURCE (Ω)
800
1000
2481 F18
Figure 18. +FS Error vs RSOURCE at REF+ or REF– (Large CREF)
10
0
0
–20
–30
CREF = 0.01µF
CREF = 0.001µF
CREF = 100pF
CREF = 0pF
–100
–FS ERROR (ppm)
–FS ERROR (ppm)
–10
–40
–50
–60 VCC = 5V
VREF = 5V
–70 V + = 1.25V
IN
–
–80 VIN = 3.75V
TA = 25°C
–90
10
0
CREF = 0.01µF
–200
CREF = 1µF, 10µF
–300
–400
1k
100
RSOURCE (Ω)
10k
100k
–500
0
2481 F17
Figure 17. –FS Error vs RSOURCE at REF+ or REF– (Small CREF)
CREF = 0.1µF
VCC = 5V
VREF = 5V
VIN+ = 1.25V
VIN– = 3.75V
TA = 25°C
200
600
400
RSOURCE (Ω)
800
1000
2481 F19
Figure 19. –FS Error vs RSOURCE at REF+ or REF– (Large CREF)
2481fd
For more information www.linear.com/LTC2481
25
LTC2481
Applications Information
In applications where the reference and input common
mode voltages are different, extra errors are introduced.
For every 1V of the reference and input common mode
voltage difference (VREFCM – VINCM) and a 5V reference,
each Ohm of reference source resistance introduces an
extra (VREFCM – VINCM)/(VREF • REQ) full-scale gain error,
which is 0.074ppm when using internal oscillator and 60Hz
mode. When using internal oscillator and 50Hz/60Hz mode,
the extra full-scale gain error is 0.067ppm. When using
internal oscillator and 50Hz mode, the extra gain error is
0.061ppm. If an external clock is used, the corresponding
extra gain error is 0.24 • 10–6 • fEOSCppm.
The magnitude of the dynamic reference current depends
upon the size of the very stable internal sampling capacitors
and upon the accuracy of the converter sampling clock. The
accuracy of the internal clock over the entire temperature
and power supply range is typically better than 0.5%. Such
a specification can also be easily achieved by an external
clock. When relatively stable resistors (50ppm/°C) are
used for the external source impedance seen by VREF+
and VREF–, the expected drift of the dynamic current gain
error will be insignificant (about 1% of its value over the
entire temperature and voltage range). Even for the most
stringent applications a one-time calibration operation
may be sufficient.
In addition to the reference sampling charge, the reference pins ESD protection diodes have a temperature dependent leakage current. This leakage current, nominally
1nA (±100nA max), results in a small gain error. A 100Ω
source resistance will create a 0.05µV typical and 5µV
maximum full-scale error.
3500
VCC = 5V
8 VREF = 5V
VIN(CM) = 2.5V
6 T = 25°C
A
4 CREF = 10µF
R = 1k
2
R = 500Ω
0
R = 100Ω
–2
–4
–6
2500
2000
1500
1000
500
–8
–10
–0.5
–0.3
0.1
–0.1
VIN/VREF (V)
0.3
50
30
Figure 22. +FS Error vs Output Data Rate and Temperature
0
–FS ERROR (ppm OF VREF)
–500
–1000
–1500
20
–2000
10
TA = 25°C
TA = 85°C
VIN(CM) = VREF(CM)
VCC = VREF = 5V
CA0/f0 = EXT CLOCK
–2500
0
–10
–3000
0
10
20
OUTPUT DATA RATE (READINGS/SEC)
30
–3500
0
2481 F21
Figure 21. Offset Error vs Output Data Rate and Temperature
26
20
10
OUTPUT DATA RATE (READINGS/SEC)
2481 F22
TA = 25°C
TA = 85°C
30
0
2481 F20
VIN(CM) = VREF(CM)
VCC = VREF = 5V
VIN = 0V
CA0/f0 = EXT CLOCK
40
0
0.5
Figure 20. INL vs DIFFERENTIAL Input Voltage and
Reference Source Resistance for CREF > 1µF
OFFSET ERROR (ppm OF VREF)
VIN(CM) = VREF(CM)
VCC = VREF = 5V
CA0/f0 = EXT CLOCK
TA = 25°C
TA = 85°C
3000
+FS ERROR (ppm OF VREF)
INL (ppm OF VREF)
10
20
10
OUTPUT DATA RATE (READINGS/SEC)
30
2481 F23
Figure 23. –FS Error vs Output Data Rate and Temperature
2481fd
For more information www.linear.com/LTC2481
LTC2481
Applications Information
Output Data Rate
When using its internal oscillator, the LTC2481 produces up
to 7.5 samples per second (sps) with a notch frequency of
60Hz, 6.25sps with a notch frequency of 50Hz and 6.82sps
with the 50Hz/60Hz rejection mode. The actual output
data rate will depend upon the length of the sleep and
data output phases which are controlled by the user and
which can be made insignificantly short. When operated
with an external conversion clock (CA0/f0 connected to
an external oscillator), the LTC2481 output data rate can
be increased as desired. The duration of the conversion
phase is 41036/fEOSC. If fEOSC = 307.2kHz, the converter
behaves as if the internal oscillator is used and the notch
is set at 60Hz.
An increase in fEOSC over the nominal 307.2kHz will
translate into a proportional increase in the maximum
output data rate. The increase in output rate is nevertheless accompanied by two potential effects, which must
be carefully considered.
First, a change in fEOSC will result in a proportional change
in the internal notch position and in a reduction of the
converter differential mode rejection at the power line frequency. In many applications, the subsequent performance
degradation can be substantially reduced by relying upon
the LTC2481’s exceptional common mode rejection and by
carefully eliminating common mode to differential mode
conversion sources in the input circuit. The user should
avoid single-ended input filters and should maintain a
very high degree of matching and symmetry in the circuits
driving the IN+ and IN– pins.
Second, the increase in clock frequency will increase
proportionally the amount of sampling charge transferred
through the input and the reference pins. If large external
input and/or reference capacitors (CIN, CREF) are used, the
previous section provides formulae for evaluating the effect
of the source resistance upon the converter performance for
any value of fEOSC. If small external input and/or reference
capacitors (CIN, CREF) are used, the effect of the external
source resistance upon the LTC2481 typical performance
can be inferred from Figures 14, 15, 16 and 17 in which
the horizontal axis is scaled by 307200/fEOSC.
Typical measured performance curves for output data rates
up to 25 readings per second are shown in Figures 21 to
28. In order to obtain the highest possible level of accuracy
from this converter at output data rates above 20 readings
per second, the user is advised to maximize the power
supply voltage used and to limit the maximum ambient
operating temperature. In certain circumstances, a reduction of the differential reference voltage may be beneficial.
Input Bandwidth
The combined effect of the internal SINC4 digital filter and
of the analog and digital autocalibration circuits determines
the LTC2481 input bandwidth. When the internal oscillator
is used with the notch set at 60Hz, the 3dB input bandwidth
is 3.63Hz. When the internal oscillator is used with the
notch set at 50Hz, the 3dB input bandwidth is 3.02Hz. If
an external conversion clock generator of frequency fEOSC
is connected to the CA0/f0 pin, the 3dB input bandwidth
is 11.8 • 10–6 • fEOSC.
Due to the complex filtering and calibration algorithms
utilized, the converter input bandwidth is not modeled
very accurately by a first order filter with the pole located
at the 3dB frequency. When the internal oscillator is used,
the shape of the LTC2481 input bandwidth is shown in
Figure 29. When an external oscillator of frequency fEOSC
is used, the shape of the LTC2481 input bandwidth can
be derived from Figure 29, 60Hz mode curve in which
the horizontal axis is scaled by fEOSC/307200.
The conversion noise (600nVRMS typical for VREF = 5V)
can be modeled by a white noise source connected to a
noise free converter. The noise spectral density is 47nV√Hz
for an infinite bandwidth source and 64nV√Hz for a single
0.5MHz pole source. From these numbers, it is clear that
particular attention must be given to the design of external
amplification circuits. Such circuits face the simultaneous
requirements of very low bandwidth (just a few Hz) in
order to reduce the output referred noise and relatively
high bandwidth (at least 500kHz) necessary to drive the
input switched-capacitor network. A possible solution is
a high gain, low bandwidth amplifier stage followed by a
high bandwidth unity-gain buffer.
2481fd
For more information www.linear.com/LTC2481
27
LTC2481
Applications Information
22
24
20
18
TA = 25°C
TA = 85°C
16
VIN(CM) = VREF(CM)
VCC = VREF = 5V
VIN = 0V
CA0/f0 = EXT CLOCK
RES = LOG 2 (VREF/NOISERMS)
14
12
10
0
20
10
OUTPUT DATA RATE (READINGS/SEC)
30
18
16
TA = 25°C
TA = 85°C
VIN(CM) = VREF(CM)
12 VCC = VREF = 5V
CA0/f0 = EXT CLOCK
RES = LOG 2 (VREF/INLMAX)
10
0
20
10
OUTPUT DATA RATE (READINGS/SEC)
14
30
2481 F25
2481 F24
Figure 24. Resolution
(NoiseRMS ≤ 1LSB) vs Output
Data Rate and Temperature
Figure 25. Resolution
(INLMAX ≤ 1LSB) vs Output
Data Rate and Temperature
24
VIN(CM) = VREF(CM)
VIN = 0V
15 CA0/f0 = EXT CLOCK
TA = 25°C
VCC = 5V, VREF = 2.5V
VCC = VREF = 5V
10
5
0
–5
–10
0
20
10
OUTPUT DATA RATE (READINGS/SEC)
2481 F26
Figure 26. Offset Error vs Output
Data Rate and Reference Voltage
20
RESOLUTION (BITS)
20
18
16 VIN(CM) = VREF(CM)
VIN = 0V
CA0/f0 = EXT CLOCK
14
TA = 25°C
RES = LOG 2 (VREF/NOISERMS)
12
VCC = 5V, VREF = 2.5V
VCC = VREF = 5V
10
0
20
10
OUTPUT DATA RATE (READINGS/SEC)
30
18
16
VIN(CM) = VREF(CM)
VIN = 0V
14 CA0/f0 = EXT CLOCK
TA = 25°C
RES = LOG 2 (VREF/INLMAX)
12
VCC = 5V, VREF = 2.5V
VCC = VREF = 5V
10
0
10
20
OUTPUT DATA RATE (READINGS/SEC)
2481 F27
Figure 28. Resolution (INLMAX ≤ 1LSB)
vs Output Data Rate and Reference Voltage
100
–1
50Hz AND
60Hz MODE
–2
50Hz MODE
60Hz MODE
–4
–5
1
3
0
4
5
2
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
2481 F29
Figure 29. Input Signal Using
the Internal Oscillator
28
INPUT REFERRED NOISE
EQUIVALENT BANDWIDTH (Hz)
INPUT SIGNAL ATTENUATION (dB)
0
–6
30
2481 F28
Figure 27. Resolution (NoiseRMS ≤ 1LSB)
vs Output Data Rate and Reference Voltage
–3
30
22
22
RESOLUTION (BITS)
OFFSET ERROR (ppm OF VREF)
20
RESOLUTION (BITS)
RESOLUTION (BITS)
22
20
60Hz MODE
10
50Hz MODE
1
0.1
0.1
1
10 100 1k
10k 100k 1M
INPUT NOISE SOURCE SINGLE POLE
EQUIVALENT BANDWIDTH (Hz) 2481 F30
Figure 30. Input Referred Noise Equivalent Bandwidth
of an Input Connected White Noise Source
2481fd
For more information www.linear.com/LTC2481
LTC2481
Applications Information
When external amplifiers are driving the LTC2481, the
ADC input referred system noise calculation can be
simplified by Figure 30. The noise of an amplifier driving
the LTC2481 input pin can be modeled as a band limited
white noise source. Its bandwidth can be approximated
by the bandwidth of a single pole lowpass filter with a
corner frequency fi. The amplifier noise spectral density
is ni. From Figure 30, using fi as the x-axis selector, we
can find on the y-axis the noise equivalent bandwidth freqi
of the input driving amplifier. This bandwidth includes
the band limiting effects of the ADC internal calibration
and filtering. The noise of the driving amplifier referred
to the converter input and including all these effects can
be calculated as N = ni • √freqi. The total system noise
(referred to the LTC2481 input) can now be obtained by
summing as square root of sum of squares the three
ADC input referred noise sources: the LTC2481 internal
noise, the noise of the IN+ driving amplifier and the noise
of the IN– driving amplifier.
One of the advantages delta-sigma ADCs offer over
conventional ADCs is on-chip digital filtering. Combined
with a large oversampling ratio, the LTC2481 significantly
simplifies antialiasing filter requirements. Additionally,
the input current cancellation feature of the LTC2481
allows external lowpass filtering without degrading the
DC performance of the device.
The SINC4 digital filter provides greater than 120dB normal
mode rejection at all frequencies except DC and integer
multiples of the modulator sampling frequency (fS). The
LTC2481’s autocalibration circuits further simplify the
antialiasing requirements by additional normal mode
signal filtering both in the analog and digital domain.
Independent of the operating mode, fS = 256 • fN = 2048
• fOUTMAX where fN is the notch frequency and fOUTMAX
is the maximum output data rate. In the internal oscillator mode with a 50Hz notch setting, fS = 12800Hz, with
50Hz/60Hz rejection, fS = 13960Hz and with a 60Hz notch
setting fS = 15360Hz. In the external oscillator mode, fS =
fEOSC/20. The performance of the normal mode rejection
is shown in Figures 31 and 32.
0
0
–10
–10
INPUT NORMAL MODE REJECTION (dB)
INPUT NORMAL MODE REJECTION (dB)
If the CA0/f0 pin is driven by an external oscillator of
frequency fEOSC, Figure 30 can still be used for noise
calculation if the x-axis is scaled by fEOSC/307200.
For large values of the ratio fEOSC/307200, the Figure 30
plot accuracy begins to decrease, but at the same time
the LTC2481 noise floor rises and the noise contribution
of the driving amplifiers lose significance.
Normal Mode Rejection and Antialiasing
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0 fS 2fS 3fS 4fS 5fS 6fS 7fS 8fS 9fS 10fS11fS12fS
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0 fS 2fS 3fS 4fS 5fS 6fS 7fS 8fS 9fS 10fS
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
2481 F32
2481 F31
Figure 31. Input Normal Mode Rejection,
Internal Oscillator and 50Hz Notch Mode
Figure 32. Input Normal Mode Rejection at DC
2481fd
For more information www.linear.com/LTC2481
29
LTC2481
Applications Information
In 1x speed mode, the regions of low rejection occurring
at integer multiples of fS have a very narrow bandwidth.
Magnified details of the normal mode rejection curves
are shown in Figure 33 (rejection near DC) and Figure 34
(rejection at fS = 256fN) where fN represents the notch
frequency. These curves have been derived for the external oscillator mode but they can be used in all operating
modes by appropriately selecting the fN value.
The user can expect to achieve this level of performance
using the internal oscillator as it is demonstrated by
Figures 35, 36 and 37. Typical measured values of the
normal mode rejection of the LTC2481 operating with an
internal oscillator and a 60Hz notch setting are shown in
Figure 35 superimposed over the theoretical calculated
curve. Similarly, the measured normal mode rejection of
the LTC2481 for the 50Hz rejection mode and 50Hz/60Hz
rejection mode are shown in Figures 36 and 37.
As a result of these remarkable normal mode specifications, minimal (if any) antialias filtering is required in front
of the LTC2481. If passive RC components are placed in
front of the LTC2481, the input dynamic current should
be considered (see Input Current section). In this case,
the differential input current cancellation feature of the
LTC2481 allows external RC networks without significant
degradation in DC performance.
0
fN = fEOSC/5120
INPUT NORMAL MODE REJECTION (dB)
INPUT NORMAL MODE REJECTION (dB)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0
fN
2fN 3fN 4fN 5fN 6fN 7fN
INPUT SIGNAL FREQUENCY (Hz)
Traditional high order delta-sigma modulators, while
providing very good linearity and resolution, suffer
from potential instabilities at large input signal levels.
The proprietary architecture used for the LTC2481 third
order modulator resolves this problem and guarantees a
predictable stable behavior at input signal levels of up to
150% of full-scale. In many industrial applications, it is
not uncommon to have to measure microvolt level signals
superimposed on volt level perturbations and the LTC2481
is eminently suited for such tasks. When the perturbation
is differential, the specification of interest is the normal
mode rejection for large input signal levels. With a reference voltage VREF = 5V, the LTC2481 has a full-scale differential input range of 5V peak-to-peak. Figures 38 and
39 show measurement results for the LTC2481 normal
mode rejection ratio with a 7.5V peak-to-peak (150% of
full scale) input signal superimposed over the more traditional normal mode rejection ratio results obtained with a
5V peak-to-peak (full-scale) input signal. In Figure 38, the
LTC2481 uses the internal oscillator with the notch set at
60Hz and in Figure 39 it uses the internal oscillator with
the notch set at 50Hz. It is clear that the LTC2481 rejection
performance is maintained with no compromises in this
extreme situation. When operating with large input signal
levels, the user must observe that such signals do not
violate the device absolute maximum ratings.
8fN
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
250fN 252fN 254fN 256fN 258fN 260fN 262fN
INPUT SIGNAL FREQUENCY (Hz)
2481 F33
Figure 33. Input Normal Mode Rejection at DC
30
2481 F34
Figure 34. Input Normal Mode Rejection at fs = 256fN
2481fd
For more information www.linear.com/LTC2481
LTC2481
Applications Information
MEASURED DATA
CALCULATED DATA
–20
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
–60
–80
–100
–120
0
15
30
45
60
75
0
NORMAL MODE REJECTION (dB)
NORMAL MODE REJECTION (dB)
0
–40
–80
–100
0
12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200
INPUT FREQUENCY (Hz)
2481 F35
2481 F36
Figure 35. Input Normal Mode Rejection vs Input Frequency
with Input Perturbation of 100% Full-Scale (60Hz Notch)
–20
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
–60
–80
–100
–120
0
20
40
60
80
100
120
140
INPUT FREQUENCY (Hz)
160
180
200
220
Figure 36. Input Normal Mode Rejection vs Input Frequency
with Input Perturbation of 100% Full-Scale (50Hz Notch)
0
NORMAL MODE REJECTION (dB)
MEASURED DATA
CALCULATED DATA
VIN(P-P) = 5V
VIN(P-P) = 7.5V
(150% OF FULL SCALE)
–20
Figure 37. Input Normal Mode Rejection vs Input Frequency
with Input Perturbation of 100% Full-Scale (50Hz/60Hz Mode)
–60
–80
–100
–120
0
15
30
45
60
75
90 105 120 135 150 165 180 195 210 225 240
INPUT FREQUENCY (Hz)
2481 F38
Figure 38. Measured Input Normal Mode Rejection
vs Input Frequency with Input Perturbation of 150%
Full-Scale (60Hz Notch)
0
VIN(P-P) = 5V
VIN(P-P) = 7.5V
(150% OF FULL SCALE)
–20
VCC = 5V
VREF = 5V
VINCM = 2.5V
TA = 25°C
–40
2481 F37
NORMAL MODE REJECTION (dB)
NORMAL MODE REJECTION (dB)
0
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
–60
–120
90 105 120 135 150 165 180 195 210 225 240
INPUT FREQUENCY (Hz)
MEASURED DATA
CALCULATED DATA
–20
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
–40
–60
–80
–100
–120
0
12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200
INPUT FREQUENCY (Hz)
2481 F39
Figure 39. Measured Input Normal Mode Rejection
vs Input Frequency with Input Perturbation of 150%
Full-Scale (50Hz Notch)
2481fd
For more information www.linear.com/LTC2481
31
LTC2481
0
0
–20
–20
INPUT NORMAL REJECTION (dB)
INPUT NORMAL REJECTION (dB)
Applications Information
–40
–60
–80
–100
–120
0
fN
2fN 3fN 4fN 5fN 6fN 7fN
INPUT SIGNAL FREQUENCY (fN)
NORMAL MODE REJECTION (dB)
NORMAL MODE REJECTION (dB)
–70
–60
–80
–100
–120
–100
Figure 41. Input Normal Mode Rejection 2x Speed Mode
MEASURED DATA
VCC = 5V
CALCULATED DATA VREF = 5V
VINCM = 2.5V
VIN(P-P) = 5V
TA = 25°C
–40
–80
2481 F41
Figure 40. Input Normal Mode Rejection 2x Speed Mode
–20
–60
–120
248 250 252 254 256 258 260 262 264
INPUT SIGNAL FREQUENCY (fN)
8fN
2481 F40
0
–40
–80
NO AVERAGE
–90
–110
–120
–130
–140
0
25
WITH
RUNNING
AVERAGE
–100
50 75 100 125 150 175 200 225
INPUT FREQUENCY (Hz)
60
62
54 56
58
48 50
52
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
2481 F43
2481 F42
Figure 42. Input Normal Mode Rejection vs Input
Frequency, 2x Speed Mode and 50Hz/60Hz Mode
Figure 43. Input Normal Mode Rejection 2x Speed Mode
5V
C8
1µF
C7
0.1µF
ISOTHERMAL
2
+
G1
NC1M4V0
LT1236
IN OUT
TRIM
GND
4
6
5
R2
2k
R7
8k
R8
1k
4
5
IN+
IN–
1
2
REF+ VCC SCL
SDA
LTC2481 CA1
CA0/f0
1.7k
REF– GND
3
TYPE K
THERMOCOUPLE
JACK
(OMEGA MPJ-K-F)
1.7k
6
7
9
10
8
2481 F44
26.3C
Figure 44. Calibration Setup
32
2481fd
For more information www.linear.com/LTC2481
LTC2481
Applications Information
Using the 2x speed mode of the LTC2481, the device
bypasses the digital offset calibration operation to double
the output data rate. The superior normal mode rejection
is maintained as shown in Figures 31 and 32. However,
the magnified details near DC and fS = 256fN are different,
see Figures 40 and 41. In 2x speed mode, the bandwidth is
11.4Hz for the 50Hz rejection mode, 13.6Hz for the 60Hz
rejection mode and 12.4Hz for the 50Hz/60Hz rejection
mode. Typical measured values of the normal mode rejection of the LTC2481 operating with the internal oscillator
and 2x speed mode is shown in Figure 42.
When the LTC2481 is configured in 2x speed mode, by
performing a running average, a SINC1 notch is combined
with the SINC4 digital filter, yielding the normal mode
rejection identical as that for the 1x speed mode. The
averaging operation still keeps the output rate with the
following algorithm:
Result 1 = average (sample 0, sample 1)
Result 2 = average (sample 1, sample 2)
……
Result n = average (sample n – 1, sample n)
The main advantage of the running average is that it
achieves simultaneous 50Hz/60Hz rejection at twice the
effective output rate, as shown in Figure 43. The raw output
data provides a better than 70dB rejection over 48Hz to
62.4Hz, which covers both 50Hz ±2% and 60Hz ±2%. With
running average on, the rejection is better than 87dB for
both 50Hz ±2% and 60Hz ±2%.
Complete Thermocouple Measurement System with
Cold Junction Compensation
The LTC2481 is ideal for direct digitization of thermocouples and other low voltage output sensors. The input
has a typical offset error of 500nV (2.5µV max) offset
drift of 10nV/°C and a noise level of 600nVRMS. The input
span may be optimized for various sensors by setting the
gain of the PGA. Using an external 5V reference with a
PGA gain of 64 gives a ±78mV input range—perfect for
thermocouples.
Figure 45 (page 39 of this data sheet) is a complete type
K thermocouple meter. The only signal conditioning is a
simple surge protection network. In any thermocouple
meter, the cold junction temperature sensor must be at
the same temperature as the junction between the thermocouple materials and the copper printed circuit board
traces. The tiny LTC2481 can be tucked neatly underneath
an Omega MPJ-K-F thermocouple socket ensuring close
thermal coupling.
The LTC2481’s 1.4mV/°C PTAT circuit measures the cold
junction temperature. Once the thermocouple voltage
and cold junction temperature are known, there are
many ways of calculating the thermocouple temperature
including a straight-line approximation, lookup tables or a
polynomial curve fit. Calibration is performed by applying
an accurate 500mV to the ADC input derived from an
LT®1236 reference and measuring the local temperature
with an accurate thermometer as shown in Figure 44. In
calibration mode, the up and down buttons are used to
adjust the local temperature reading until it matches an
accurate thermometer. Both the voltage and temperature
calibration are easily automated.
The complete microcontroller code for this application is
available on the LTC2481 product webpage at:
http://www.linear.com
It can be used as a template for may different instruments
and it illustrates how to generate calibration coefficients
for the onboard temperature sensor. Extensive comments
detail the operation of the program. The read_LTC2481()
function controls the operation of the LTC2481 and is
listed below for reference.
2481fd
For more information www.linear.com/LTC2481
33
LTC2481
Applications Information
/*
LTC248X.h
Processor setup and
Lots of useful defines for configuring the LTC2481 and LTC2485.
*/
#include
#use delay(clock=6000000)
// Device
// 6MHz clock
//#fuses NOWDT,HS, PUT, NOPROTECT, NOBROWNOUT
// Configuration fuses
#rom 0x2007={0x3F3A} // Equivalent and more reliable fuse config.
#use I2C(master, sda=PIN_C5, scl=PIN_C3, SLOW)// Set up i2c port
#include “PCM73A.h”
// Various defines
#include “lcd.c”
// LCD driver functions
// Useful defines for the LTC2481 and LTC2485 - OR them together to make the
// 8 bit config word.
#define READ
0x01
// bitwise OR with address for read or write
#define WRITE
0x00
#define LTC248XADDR 0b01001000
// The one and only LTC248X in this circuit,
// with both address lines floating.
// Select gain - 1 to 256 (also depends on speed setting)
#define GAIN1 0b00000000
// G = 1
(SPD = 0), G = 1
(SPD = 1)
#define GAIN2 0b00100000
// G = 4
(SPD = 0), G = 2
(SPD = 1)
#define GAIN3 0b01000000
// G = 8
(SPD = 0), G = 4
(SPD = 1)
#define GAIN4 0b01100000
// G = 16 (SPD = 0), G = 8
(SPD = 1)
#define GAIN5 0b10000000
// G = 32 (SPD = 0), G = 16 (SPD = 1)
#define GAIN6 0b10100000
// G = 64 (SPD = 0), G = 32 (SPD = 1)
#define GAIN7 0b11000000
// G = 128 (SPD = 0), G = 64 (SPD = 1)
#define GAIN8 0b11100000
// G = 256 (SPD = 0), G = 128 (SPD = 1)
// Select ADC source - differential input or PTAT circuit
#define VIN
0b00000000
#define PTAT
0b00001000
// Select rejection frequency - 50, 55, or 60Hz
#define R50
0b00000010
#define R55
0b00000000
#define R60
0b00000100
// Speed settings is bit 7 in the 2nd byte
#define SLOW
0b00000000 // slow output rate with autozero
#define FAST
0b00000001 // fast output rate with no autozero
34
2481fd
For more information www.linear.com/LTC2481
LTC2481
Applications Information
/*
LTC2481.c
Basic voltmeter test program for LTC2481
Reads LTC2481 input at gain = 1, 1X speed mode, converts to volts,
and prints voltage to a 2 line by 16 character LCD display.
Mark Thoren
Linear Technology Corporation
June 23, 2005
Written for CCS PCM compiler, Version 3.182
*/
#include “LTC248X.h”
/*** read_LTC2481() ************************************************************
This is the function that actually does all the work of talking to the LTC2481.
Arguments:
addr - device address
config - configuration bits for next conversion
Returns:
zero if conversion is in progress,
32 bit signed integer with lower 8 bits clear, 24 bit LTC2481
output word in the upper 24 bits. Data is left-justified for
compatibility with the 24 bit LTC2485.
the i2c_xxxx() functions do the following:
void i2c_start(void): generate an i2c start or repeat start condition
void i2c_stop(void): generate an i2c stop condition
char i2c_read(boolean): return 8 bit i2c data while generating an ack or nack
boolean i2c_write(): send 8 bit i2c data and return ack or nack from slave device
These functions are very compiler specific, and can use either a hardware i2c
port or software emulation of an i2c port. This example uses software emulation.
A good starting point when porting to other processors is to write your own
i2c functions. Note that each processor has its own way of configuring
the i2c port, and different compilers may or may not have built-in functions
for the i2c port.
When in doubt, you can always write a “bit bang” function for troubleshooting purposes.
The “fourbytes” structure allows byte access to the 32 bit return value:
struct fourbytes // Define structure of four consecutive bytes
{
// To allow byte access to a 32 bit int or float.
int8 te0;
//
int8 te1;
// The make32() function in this compiler will
int8 te2;
// also work, but a union of 4 bytes and a 32 bit int
int8 te3;
// is probably more portable.
};
Also note that the lower 4 bits are the configuration word from the previous conversion.
2481fd
For more information www.linear.com/LTC2481
35
LTC2481
Applications Information
*******************************************************************************/
signed int32 read_LTC2481(char addr, char config)
{
struct fourbytes // Define structure of four consecutive bytes
{
// To allow byte access to a 32 bit int or float.
int8 te0;
//
int8 te1;
// The make32() function in this compiler will
int8 te2;
// also work, but a union of 4 bytes and a 32 bit int
int8 te3;
// is probably more portable.
};
union
// adc_code.bits32
all 32 bits
{
// adc_code.by.te0
byte 0
signed int32 bits32;
// adc_code.by.te1
byte 1
struct fourbytes by;
// adc_code.by.te2
byte 2
} adc_code;
// adc_code.by.te3
byte 3
// Start communication with LTC2481:
i2c_start();
if(i2c_write(addr | WRITE))// If no acknowledge, return zero
{
i2c_stop();
return 0;
}
i2c_write(config);
i2c_start();
i2c_write(addr | READ);
adc_code.by.te3 = i2c_read();
adc_code.by.te2 = i2c_read();
adc_code.by.te1 = i2c_read();
adc_code.by.te0 = 0;
i2c_stop();
return adc_code.bits32;
} // End of read_LTC2481()
/*** initialize() **************************************************************
Basic hardware initialization of controller and LCD, send Hello message to LCD
*******************************************************************************/
void initialize(void)
{
// General initialization stuff.
setup_adc_ports(NO_ANALOGS);
setup_adc(ADC_OFF);
setup_counters(RTCC_INTERNAL,RTCC_DIV_1);
setup_timer_1(T1_DISABLED);
setup_timer_2(T2_DISABLED,0,1);
// This is the important part - configuring the SPI port
setup_spi(SPI_MASTER|SPI_L_TO_H|SPI_CLK_DIV_16|SPI_SS_DISABLED); // fast SPI clock
CKP = 0; // Set up clock edges - clock idles low, data changes on
CKE = 1; // falling edges, valid on rising edges.
36
2481fd
For more information www.linear.com/LTC2481
LTC2481
Applications Information
lcd_init();
delay_ms(6);
printf(lcd_putc, “Hello!”);
delay_ms(500);
} // End of initialize()
// Initialize LCD
// Obligatory hello message
// for half a second
*** main() ********************************************************************
Main program initializes microcontroller registers, then reads the LTC2481
repeatedly
*******************************************************************************/
void main()
{
signed int32 x;
// Integer result from LTC2481
float voltage;
// Variable for floating point math
int16 timeout;
initialize();
// Hardware initialization
while(1)
{
delay_ms(1);
//
//
//
//
//
// Pace the main loop to something more than 1 ms
This is a basic error detection scheme. The LTC248X will never take more than
163.5ms, 149.9ms, or 136.5ms to complete a conversion in the 50Hz, 55Hz, and 60Hz
rejection modes, respectively.
If read_LTC248X() does not return non-zero within this time period, something
is wrong, such as an incorrect i2c address or bus conflict.
if((x = read_LTC2481(LTC248XADDR, GAIN1 | VIN | R55)) != 0)
{
// No timeout, everything is okay
timeout = 0;
// reset timer
x &= 0xFFFFFFC0;
// clear config bits so they don’t affect math
x ^= 0x80000000;
// Invert MSB, result is 2’s complement
voltage = (float) x;
// convert to float
voltage = voltage * 5.0 / 2147483648.0;// Multiply by Vref, divide by 2^31
lcd_putc(‘\f’);
// Clear screen
lcd_gotoxy(1,1);
// Goto home position
printf(lcd_putc, “V %01.4f”, voltage); // Display voltage
}
else
{
++timeout;
}
if(timeout > 200)
{
timeout = 200;
// Prevent rollover
lcd_gotoxy(1,1);
printf(lcd_putc, “ERROR - TIMEOUT”);
delay_ms(500);
}
} // End of main loop
} // End of main()
2481fd
For more information www.linear.com/LTC2481
37
LTC2481
Package Description
DD Package
10-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1699 Rev B)
0.70 ±0.05
3.55 ±0.05
1.65 ±0.05
2.15 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ± 0.05
0.50
BSC
2.38 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
3.00 ±0.10
(4 SIDES)
R = 0.125
TYP
6
0.40 ± 0.10
10
1.65 ± 0.10
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
0.200 REF
5
0.75 ±0.05
0.00 – 0.05
1
(DD) DFN REV B 0309
0.25 ± 0.05
0.50 BSC
2.38 ±0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2).
CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
38
2481fd
For more information www.linear.com/LTC2481
LTC2481
Revision History
REV
DATE
DESCRIPTION
PAGE NUMBER
A
11/09
Update Tables 3 and 4
B
04/10
Added H-grade to Absolute Maximum Ratings, Order Information, Electrical Characteristics (Normal Speed),
Converter Characteristics, Power Requirements, Timing Characteristics, and Typical Performance Characteristics
C
06/10
Revised Typical Application drawing
Added text to I2C Interface section
1
12
D
09/14
Clarify Temperature Sensor Performance
1, 2
Clarify Performance vs fO Frequency, reducing external oscillator max frequency to 1MHz
16
2-10
5, 8, 26, 28
2481fd
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LTC2481
39
LTC2481
Typical Application
5V
C8
1µF
PIC16F73
C7
0.1µF
ISOTHERMAL
1.7k
1.7k
3
R2
2k
4
REF
IN+
2
VCC
LTC2481
TYPE K
THERMOCOUPLE
JACK
(OMEGA MPJ-K-F)
5
SCL
SDA
6
7
IN–
10
CA1 GND REF– CAO/fO
9
8
3
5V
D7
D6
2 × 16 CHARACTER
D5
LCD DISPLAY
D4
(OPTREX DMC162488
EN
OR SIMILAR)
RW
CONTRAST
GND D0 D1 D2 D3 RS
VCC
5V
1
R6
5k
3
2
5V
18
17
16
15
14
13
12
11
28
27
26
25
24
23
22
21
7
6
5
4
3
2
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
RA5
RA4
RA3
RA2
RA1
RA0
VDD
OSC1
OSC2
MCLR
20
C6
0.1µF
9
5V
Y1
6MHz
10
R1
1 10k
D1
BAT54
5V
9
VSS
19
VSS
2481 F45
R3
10k
CALIBRATE
2
1
DOWN
R4
10k
R5
10k
UP
Figure 45. Complete Type K Thermocouple Meter
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LT1236A-5
Precision Bandgap Reference, 5V
0.05% Max Initial Accuracy, 5ppm/°C Drift
LT1460
Micropower Series Reference
0.075% Max Initial Accuracy, 10ppm/°C Max Drift
LT1790
Micropower SOT-23 Low Dropout Reference Family
0.05% Max Initial Accuracy, 10ppm/°C Max Drift
LTC2400
24-Bit, No Latency ∆Σ ADC in SO-8
0.3ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200µA
LTC2410
24-Bit, No Latency ∆Σ ADC with Differential Inputs
0.8µVRMS Noise, 2ppm INL
LTC2411/LTC2411-1 24-Bit, No Latency ∆Σ ADCs with Differential Inputs in MSOP
1.45µVRMS Noise, 4ppm INL, Simultaneous 50Hz/60Hz Rejection
(LTC2411-1)
LTC2413
Simultaneous 50Hz/60Hz Rejection, 800nVRMS Noise
24-Bit, No Latency ∆Σ ADC with Differential Inputs
LTC2415/LTC2415-1 24-Bit, No Latency ∆Σ ADCs with 15Hz Output Rate
Pin Compatible with the LTC2410
LTC2414/LTC2418
8-/16-Channel 24-Bit, No Latency ∆Σ ADCs
0.2ppm Noise, 2ppm INL, 3ppm Total Unadjusted Errors 200µA
LTC2440
High Speed, Low Noise 24-Bit ∆Σ ADC
3.5kHz Output Rate, 200nV Noise, 24.6 ENOBs
LTC2480
16-Bit ∆Σ ADC with Easy Drive Inputs, 600nV Noise,
Programmable Gain, and Temperature Sensor
Pin Compatible with LTC2482/LTC2484
LTC2482
16-Bit ∆Σ ADC with Easy Drive Inputs
Pin Compatible with LTC2480/LTC2484
LTC2483
16-Bit ∆Σ ADC with Easy Drive Inputs, I2C Interface
Pin Compatible with LTC2481/LTC2483
LTC2484
24-Bit ∆Σ ADC with Easy Drive Inputs
Pin Compatible with LTC2480/LTC2482
LTC2485
24-Bit ∆Σ ADC with Easy Drive Inputs, I2C Interface and
Pin Compatible with LTC2481/LTC2483
Temperature Sensor
40 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC2481
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC2481
2481fd
LT 0914 REV D • PRINTED IN USA
LINEAR TECHNOLOGY CORPORATION 2005