LTC2498
24-Bit 8-/16-Channel ΔS
ADC with Easy Drive Input
Current Cancellation
Description
Features
Up to 8 Differential or 16 Single-Ended Inputs
n Easy Drive™ Technology Enables Rail-to-Rail
Inputs with Zero Differential Input Current
n Directly Digitizes High Impedance Sensors with
Full Accuracy
n 600nV RMS Noise
n Integrated High Accuracy Temperature Sensor
n GND to V
CC Input/Reference Common Mode Range
n Programmable 50Hz, 60Hz or Simultaneous
50Hz/60Hz Rejection Mode
n 2ppm INL, No Missing Codes
n 1ppm Offset and 15ppm Full-Scale Error
n 2x Speed Mode (15Hz Using Internal Oscillator)
n No Latency: Digital Filter Settles in a Single Cycle,
Even After a New Channel Is Selected
n Single Supply 2.7V to 5.5V Operation (0.8mW)
n Internal Oscillator
n Tiny QFN 5mm × 7mm Package
The LTC®2498 is a 16-channel (8-differential) 24-bit No
Latency DS™ ADC with Easy Drive technology. The patented sampling scheme eliminates dynamic input current
errors and the shortcomings of on-chip buffering through
automatic cancellation of differential input current. This
allows large external source impedances, and rail-to-rail
input signals to be directly digitized while maintaining
exceptional DC accuracy.
n
The LTC2498 includes a high accuracy temperature sensor
and an integrated oscillator. This device can be configured
to measure an external signal (from combinations of 16
analog input channels operating in single ended or differential modes) or its internal temperature sensor. The
integrated temperature sensor offers 1/30th °C resolution
and 2°C absolute accuracy.
The LTC2498 allows a wide common mode input range
(0V to VCC), independent of the reference voltage. Any
combination of single-ended or differential inputs can be
selected and the first conversion after a new channel is
selected is valid. Access to the multiplexer output enables
optional external amplifiers to be shared between all analog
inputs and auto calibration continuously removes their
associated offset and drift.
Applications
n
n
n
n
Direct Sensor Digitizer
Direct Temperature Measurement
Instrumentation
Industrial Process Control
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
No Latency ∆∑ and Easy Drive are trademarks of Linear Technology Corporation. All other
trademarks are the property of their respective owners.
Typical Application
Internal Sensor
Absolute Temperature Error
Data Acquisition System with Temperature Compensation
5
2.7V TO 5.5V
TEMPERATURE
SENSOR
MUXOUT/
ADCIN
VCC
0.1µF
REF+
IN+
24-BIT ∆Σ ADC
WITH EASY DRIVE
IN–
MUXOUT/
ADCIN
REF–
SDI
SCK
SDO
CS
10µF
4-WIRE
SPI INTERFACE
fO
OSC
2498 TA01a
3
ABSOLUTE ERROR (°C)
CH0
CH1
•
•
•
CH7 16-CHANNEL
MUX
CH8
•
•
•
CH15
COM
4
2
1
0
–1
–2
–3
–4
–5
–55
–30
–5
20
45
70
TEMPERATURE (°C)
95
120
2498 TA01b
2498fg
For more information www.linear.com/LTC2498
1
LTC2498
Pin Configuration
Supply Voltage (VCC).................................... –0.3V to 6V
Analog Input Voltage
(CH0 to CH15, COM)..................–0.3V to (VCC + 0.3V)
Reference Input Voltage
ADCINN, ADCINP, MUXOUTP,
MUXOUTN.................................–0.3V to (VCC + 0.3V)
Digital Input Voltage......................–0.3V to (VCC + 0.3V)
Digital Output Voltage....................–0.3V to (VCC + 0.3V)
Operating Temperature Range
LTC2498C................................................. 0°C to 70°C
LTC2498I..............................................–40°C to 85°C
LTC2498H........................................... –40°C to 125°C
Storage Temperature Range................... –65°C to 150°C
GND
GND
SDI
fO
CS
SDO
SCK
TOP VIEW
38 37 36 35 34 33 32
GND 1
31 GND
NC 2
30 REF–
GND 3
29 REF+
GND 4
28 VCC
GND 5
27 MUXOUTN
GND 6
26 ADCINN
39
COM 7
25 ADCINP
CH0 8
24 MUXOUTP
CH1 9
23 CH15
CH2 10
22 CH14
CH3 11
21 CH13
20 CH12
CH4 12
CH11
CH10
CH9
CH8
CH5
13 14 15 16 17 18 19
CH7
(Notes 1, 2)
CH6
Absolute Maximum Ratings
UHF PACKAGE
38-LEAD (5mm × 7mm) PLASTIC QFN
TJMAX = 125°C, θJA = 34°C/W
EXPOSED PAD (PIN 39) IS GND, MUST BE SOLDERED TO PCB
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2498CUHF#PBF
LTC2498CUHF#TRPBF
2498
38-Lead (5mm × 7mm) Plastic QFN
0°C to 70°C
LTC2498IUHF#PBF
LTC2498IUHF#TRPBF
2498
38-Lead (5mm × 7mm) Plastic QFN
–40°C to 85°C
LTC2498HUHF#PBF
LTC2498HUHF#TRPBF
2498
38-Lead (5mm × 7mm) Plastic QFN
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
Electrical Characteristics (Normal Speed)
The l denotes the specifications which
apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
Resolution (No Missing Codes)
0.1V ≤ VREF ≤ VCC, –FS ≤ VIN ≤ +FS (Note 5)
Integral Nonlinearity
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6)
H Grade
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
Offset Error
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 14)
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN+ = 0.25VREF, IN– = 0.75VREF
2.5V ≤ VREF ≤ VCC, IN+ = 0.25VREF, IN– = 0.75VREF
Offset Error Drift
Positive Full-Scale Error
Positive Full-Scale Error Drift
Negative Full-Scale Error
Negative Full-Scale Error Drift
MIN
TYP
MAX
2
10
12
24
l
l
Bits
1
l
UNITS
0.5
2.5
10
0.1
0.1
ppm of VREF
ppm of VREF/°C
25
l
µV
nV/°C
25
l
ppm of VREF
ppm of VREF
ppm of VREF
ppm of VREF
ppm of VREF/°C
2498fg
2
For more information www.linear.com/LTC2498
LTC2498
Electrical
Characteristics (Normal Speed)
The l denotes the specifications which
apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
MIN
TYP
Total Unadjusted Error
5V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V
15
15
15
ppm of VREF
ppm of VREF
ppm of VREF
Output Noise
5.5V < VCC < 2.7V, 2.5V ≤ VREF ≤ VCC,
GND ≤ IN+ = IN– ≤ VCC (Note 13)
0.6
µVRMS
Internal PTAT Signal
TA = 27°C (Note 5)
27.8
28.0
Internal PTAT Temperature Coefficient
MAX
UNITS
28.2
mV
93.5
µV/°C
Electrical
Characteristics (2x Speed)
The l denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
MIN
Resolution (No Missing Codes)
0.1V ≤ VREF ≤ VCC, –FS ≤ VIN ≤ +FS (Note 5)
Integral Nonlinearity
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6)
2.7V ≤ VCC ≤5.5V, VREF = 2.5V, VIN(CM) = 1.2V (Note 6)
Offset Error
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 14)
Offset Error Drift
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
2.5V ≤ VREF ≤ VCC, IN+ = 0.25VREF, IN– = 0.75VREF
2.5V ≤ VREF ≤ VCC, IN+ = 0.25VREF, IN– = 0.75VREF
5V ≤ VCC ≤ 2.5V, VREF = 5V, GND ≤ IN+ = IN– ≤ VCC
Positive Full-Scale Error
Positive Full-Scale Error Drift
Negative Full-Scale Error
Negative Full-Scale Error Drift
Output Noise
TYP
MAX
UNITS
l
2
1
10
ppm of VREF
ppm of VREF
l
0.5
2
mV
25
ppm of VREF
24
Bits
100
nV/°C
l
0.1
ppm of VREF/°C
25
l
ppm of VREF
0.1
ppm of VREF/°C
0.85
µVRMS
Converter
Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
PARAMETER
CONDITIONS
Input Common Mode Rejection DC
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 5)
Input Common Mode Rejection 60Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 5)
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 5)
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Notes 5, 7)
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Notes 5, 8)
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Notes 5, 9)
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 5)
VREF = 2.5V, IN+ = IN– = GND
VREF = 2.5V, IN+ = IN– = GND (Notes 7, 9)
VREF = 2.5V, IN+ = IN– = GND (Notes 8, 9)
Input Common Mode Rejection 50Hz ±2%
Input Normal Mode Rejection 50Hz ±2%
Input Normal Mode Rejection 60Hz ±2%
Input Normal Mode Rejection 50Hz/60Hz ±2%
Reference Common Mode Rejection DC
Power Supply Rejection DC
Power Supply Rejection, 50Hz ±2%
Power Supply Rejection, 60Hz ±2%
MIN
l
TYP
MAX
UNITS
140
dB
l
140
dB
l
140
dB
l
110
120
dB
l
110
120
dB
140
dB
l
87
l
120
dB
120
dB
120
dB
120
dB
Analog
Input and Reference
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
IN+
Absolute/Common Mode IN+ Voltage
(IN+ Corresponds to the Selected Positive Input Channel)
CONDITIONS
MIN
TYP
MAX
UNITS
GND – 0.3V
VCC + 0.3V
V
IN–
Absolute/Common Mode IN– Voltage
(IN– Corresponds to the Selected Negative Input Channel
or COM)
GND – 0.3V
VCC + 0.3V
V
2498fg
For more information www.linear.com/LTC2498
3
LTC2498
Analog
Input and Reference
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
VIN
Input Voltage Range (IN+ – IN–)
CONDITIONS
MIN
TYP
Differential/Single-Ended
l
–FS
FS
Full Scale of the Input (IN+ – IN–)
Differential/Single-Ended
l
0.5VREF
FS/224
MAX
UNITS
+FS
V
V
LSB
Least Significant Bit of the Output Code
l
REF+
Absolute/Common Mode REF+ Voltage
l
0.1
VCC
V
REF–
Absolute/Common Mode REF– Voltage
l
GND
REF+ –
0.1V
V
VREF
Reference Voltage Range (REF+ – REF–)
l
0.1
VCC
V
CS(IN+)
IN+ Sampling Capacitance
CS(IN–)
IN– Sampling Capacitance
11
pF
CS(VREF)
VREF Sampling Capacitance
11
pF
IDC_LEAK(IN+)
IN+ DC Leakage Current
Sleep Mode, IN+ = GND
l
–10
1
IN– DC Leakage Current
Sleep Mode, IN– = GND
l
–10
Sleep Mode, REF+ = VCC
l
–100
IDC_LEAK(REF )
MUX Break-Before-Make
tOPEN
Sleep Mode, REF– = GND
l
–100
QIRR
VIN = 2VP-P DC to 1.8MHz
–
11
IDC_LEAK(IN )
IDC_LEAK(REF+) REF+ DC Leakage Current
–
REF– DC Leakage Current
MUX Off Isolation
pF
10
nA
1
10
nA
1
100
nA
1
100
nA
50
ns
120
dB
Digital
Inputs and Digital Outputs
The l denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
VIH
High Level Input Voltage (CS, fO, SDI)
2.7V ≤ VCC ≤ 5.5V (Note 18)
l
VIL
Low Level Input Voltage (CS, fO, SDI)
2.7V ≤ VCC ≤ 5.5V
l
VIH
High Level Input Voltage (SCK)
2.7V ≤ VCC ≤ 5.5V (Notes 10, 15)
l
TYP
MAX
UNITS
VCC – 0.5
V
0.5
V
VCC – 0.5
V
VIL
Low Level Input Voltage (SCK)
2.7V ≤ VCC ≤ 5.5V (Notes 10, 15)
l
0.5
V
IIN
Digital Input Current (CS, fO, SDI)
0V ≤ VIN ≤ VCC
l
–10
10
µA
IIN
Digital Input Current (SCK)
0V ≤ VIN ≤ VCC (Notes 10, 15)
l
–10
10
µA
CIN
Digital Input Capacitance (CS, fO, SDI)
CIN
Digital Input Capacitance (SCK)
(Notes 10, 17)
VOH
High Level Output Voltage (SDO)
IO = –800µA (Notes 10, 17)
l
VOL
Low Level Output Voltage (SDO)
IO = 1.6mA (Notes 10, 17)
l
VOH
High Level Output Voltage (SCK)
IO = –800µA
l
VOL
Low Level Output Voltage (SCK)
IO = 1.6mA
l
IOZ
Hi-Z Output Leakage (SDO)
l
10
pF
10
pF
VCC – 0.5
V
0.4
V
VCC – 0.5
V
–10
0.4
V
10
µA
Power
Requirements
The l denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
VCC
Supply Voltage
ICC
Supply Current
CONDITIONS
MIN
l
Conversion Current (Note 12)
Temperature Measurement (Note 12)
Sleep Mode (Note 12)
H-Grade
l
l
l
l
TYP
2.7
160
200
1
MAX
UNITS
5.5
V
275
300
2
2.5
µA
µA
µA
µA
2498fg
4
For more information www.linear.com/LTC2498
LTC2498
Digital
Inputs and Digital Outputs
The l denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
(Note 16)
MIN
TYP
MAX
UNITS
fEOSC
External Oscillator Frequency Range
l
10
1000
kHz
tHEO
External Oscillator High Period
l
0.125
50
µs
tLEO
External Oscillator Low Period
l
0.125
50
µs
tCONV_1
Conversion Time for 1x Speed Mode
50Hz Mode
60Hz Mode
Simultaneous 50/60Hz Mode
External Oscillator
l
l
l
157.2
131
144.1
160.3
133.6
146.9
41036/fEOSC (in kHz)
163.5
136.3
149.9
ms
ms
ms
ms
tCONV_2
Conversion Time for 2x Speed Mode
50Hz Mode
60Hz Mode
Simultaneous 50/60Hz Mode
External Oscillator
l
l
l
78.7
65.6
72.2
80.3
66.9
73.6
81.9
68.2
75.1
ms
ms
ms
ms
fISCK
Internal SCK Frequency
Internal Oscillator (Note 10)
External Oscillator (Notes 10, 11)
DISCK
Internal SCK Duty Cycle
(Note 10)
l
fESCK
External SCK Frequency Range
(Note 10)
l
tLESCK
External SCK LOW Period
(Note 10)
l
tHESCK
External SCK High Period
(Note 10)
l
125
tDOUT_ISCK
Internal SCK 32-Bit Data Output Time
Internal Oscillator
External Oscillator
l
0.81
tDOUT_ESCK
External SCK 32-Bit Data Output Time
(Note 10)
t1
CS↓ to SDO Low
t2
CS↑ to SDO Hi-Z
20556/fEOSC (in kHz)
38.4
fEOSC/8
45
kHz
kHz
55
%
4000
kHz
125
ns
ns
0.83
256/fEOSC (in kHz)
0.85
32/fESCK (in kHz)
ms
ms
ms
l
0
200
ns
l
0
200
ns
CS↓ to SCK↑
Internal SCK Mode
l
0
200
ns
t4
CS↓ to SCK↑
External SCK Mode
l
50
tKQMAX
SCK↓ to SDO Valid
t3
200
l
(Note 5)
ns
ns
l
15
ns
50
ns
tKQMIN
SDO Hold After SCK↓
t5
SCK Set-Up Before CS↓
l
t6
SCK Hold After CS↓
l
t7
SDI Setup Before SCK↑
t8
SDI Hold After SCK↑
50
ns
(Note 5)
l
100
ns
(Note 5)
l
100
ns
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may
cause permanent damage to the device. Exposure to any Absolute Maximum
Rating condition for extended periods may affect device reliability and lifetime.
Note 2: All voltage values are with respect to GND.
Note 3: VCC = 2.7V to 5.5V unless otherwise specified.
VREFCM = VREF/2, FS = 0.5VREF
VIN = IN+ – IN–, VIN(CM) = (IN+ – IN–)/2,
where IN+ and IN– are the selected input channels.
Note 4: Use internal conversion clock or external conversion clock source
with fEOSC = 307.2kHz unless other wise specified.
Note 5: Guaranteed by design, not subject to test.
Note 6: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve. The
deviation is measured from the center of the quantization band.
Note 7: 50Hz mode (internal oscillator) or fEOSC = 256kHz ±2% (external oscillator).
Note 8: 60Hz mode (internal oscillator) or fEOSC = 307.2kHz ±2% (external
oscillator).
Note 9: Simultaneous 50Hz/60Hz mode (internal oscillator) or fEOSC =
280kHz ±2% (external oscillator).
Note 10: The SCK can be configured in external SCK mode or internal SCK
mode. In external SCK mode, the SCK pin is used as a digital input and the
driving clock is fESCK. In the internal SCK mode, the SCK pin is used as a
digital output and the output clock signal during the data output is fISCK.
Note 11: The external oscillator is connected to the fO pin. The external
oscillator frequency, fEOSC, is expressed in kHz.
Note 12: The converter uses its internal oscillator.
Note 13: The output noise includes the contribution of the internal
calibration operations.
Note 14: Guaranteed by design and test correlation.
Note 15: The converter is in external SCK mode of operation such that the
SCK pin is used as a digital input. The frequency of the clock signal driving
SCK during the data output is fESCK and is expressed in Hz.
Note 16: Refer to Applications Information section for performance vs
data rate graphs.
Note 17: The converter is in internal SCK mode of operation such that the
SCK pin is used as a digital output.
Note 18: For VCC < 3V, VIH is 2.5V for Pin fO.
For more information www.linear.com/LTC2498
2498fg
5
LTC2498
Typical Performance Characteristics
3
–45°C
1
25°C
0
85°C
–1
3
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
fO = GND
2
INL (ppm OF VREF)
1
–45°C, 25°C, 90°C
0
–1
–2
–2
–3
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
2
–0.75
0
VCC = 5V
VREF = 5V
VIN(CM) = 1.25V
fO = GND
8
85°C
–45°C
–4
2
12
85°C
–4
Noise Histogram (6.8sps)
12
12
NUMBER OF READINGS (%)
8
6
4
–0.75
–4
–0.25
0.25
0.75
INPUT VOLTAGE (V)
2498 G06
VCC = 5V, VREF = 5V, VIN = 0V, VIN(CM) = 2.5V
4 TA = 25°C, RMS NOISE = 0.60µV
3
4
0
–3 –2.4 –1.8 –1.2 –0.6 0 0.6
OUTPUT READING (µV)
1.25
Long-Term ADC Readings
6
0
2498 G07
–0.75
5
8
2
1.8
85°C
–45°C
–12
–1.25
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
10,000 CONSECUTIVE
READINGS
RMS = 0.59µV
VCC = 2.7V
AVERAGE = –0.19µV
VREF = 2.5V
10 VIN = 0V
TA = 25°C
2
1.2
25°C
0
Noise Histogram (7.5sps)
14
–3 –2.4 –1.8 –1.2 –0.6 0 0.6
OUTPUT READING (µV)
4
2498 G05
14
1.25
–8
2498 G04
NUMBER OF READINGS (%)
8
–45°C
0
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
fO = GND
25°C
4
–12
–1.25
2.5
10,000 CONSECUTIVE
READINGS
RMS = 0.60µV
VCC = 5V
AVERAGE = –0.69µV
VREF = 5V
10 VIN = 0V
TA = 25°C
–0.25
0.25
0.75
INPUT VOLTAGE (V)
Total Unadjusted Error
(VCC = 2.7V, VREF = 2.5V)
–8
–8
–12
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
–0.75
2498 G03
TUE (ppm OF VREF)
4
12
25°C
–1
Total Unadjusted Error
(VCC = 5V, VREF = 2.5V)
TUE (ppm OF VREF)
TUE (ppm OF VREF)
8
–45°C, 25°C, 90°C
0
2498 G02
Total Unadjusted Error
(VCC = 5V, VREF = 5V)
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
fO = GND
1
–3
–1.25
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
2498 G01
12
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
fO = GND
–2
–3
–1.25
2.5
Integral Nonlinearity
(VCC = 2.7V, VREF = 2.5V)
2
ADC READING (µV)
INL (ppm OF VREF)
3
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
fO = GND
2
Integral Nonlinearity
(VCC = 5V, VREF = 2.5V)
INL (ppm OF VREF)
Integral Nonlinearity
(VCC = 5V, VREF = 5V)
2
1
0
–1
–2
–3
–4
1.2
1.8
2498 G08
–5
0
10
30
40
20
TIME (HOURS)
50
60
2498 G09
2498fg
6
For more information www.linear.com/LTC2498
LTC2498
Typical Performance Characteristics
RMS Noise
vs Input Differential Voltage
RMS NOISE (ppm OF VREF)
0.9
RMS Noise vs VIN(CM)
1.0
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
0.9
RMS NOISE (µV)
0.8
0.7
0.6
0.5
RMS Noise vs Temperature (TA)
1.0
0.8
0.7
0.6
0.4
2.5
–1
0
2
1
3
5
4
RMS NOISE (µV)
RMS NOISE (µV)
RMS Noise vs VREF
0.6
0.3
VCC = 5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
0.9
0.7
0.8
0.7
0.6
0.5
0.5
3.1
3.5
3.9 4.3
VCC (V)
4.7
5.1
0.4
5.5
0
1
2
3
VREF (V)
4
0.3
OFFSET ERROR (ppm OF VREF)
OFFSET ERROR (ppm OF VREF)
0.1
0
–0.1
–0.2
–0.3
–45 –30 –15
0 15 30 45 60
TEMPERATURE (°C)
75
90
2498 G16
5
0.2
0.1
0.1
0
–0.1
–0.2
–0.3
–1
0
1
3
2
VIN(CM) (V)
5
4
6
2498 G15
Offset Error vs VCC
Offset Error vs VREF
0.3
REF+ = 2.5V
– = GND
REF
VIN = 0V
VIN(CM) = GND
TA = 25°C
0
–0.1
VCC = 5V
REF– = GND
VIN = 0V
VIN(CM) = GND
TA = 25°C
0.2
0.1
0
–0.1
–0.2
–0.3
2.7
90
VCC = 5V
VREF = 5V
VIN = 0V
TA = 25°C
0.2
OFFSET ERROR (ppm OF VREF)
Offset Error vs Temperature
0.2
75
Offset Error vs VIN(CM)
2498 G14
2498 G13
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
fO = GND
0 15 30 45 60
TEMPERATURE (°C)
2498 G12
OFFSET ERROR (ppm OF VREF)
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
0.4
2.7
0.4
–45 –30 –15
6
2498 G11
1.0
0.8
0.3
0.6
VIN(CM) (V)
RMS Noise vs VCC
0.9
0.7
0.5
2498 G10
1.0
0.8
0.5
0.4
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5 2
INPUT DIFFERENTIAL VOLTAGE (V)
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
0.9
RMS NOISE (µV)
1.0
–0.2
3.1
3.5
3.9 4.3
VCC (V)
4.7
5.1
5.5
2498 G17
–0.3
0
1
2
3
VREF (V)
4
5
2498 G18
2498fg
For more information www.linear.com/LTC2498
7
LTC2498
Typical Performance Characteristics
On-Chip Oscillator Frequency
vs Temperature
310
306
304
VCC = 4.1V
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
fO = GND
300
–45 –30 –15
75
306
304
2.5
3.0
3.5
4.0
VCC (V)
4.5
5.0
–100
200
VCC = 4.1V DC ±0.7V
= 2.5V
V
–20 INREF
+ = GND
– = GND
IN
–40 fO = GND
TA = 25°C
–60
–80
–100
–120
–120
0 20 40 60 80 100 120 140 160 180 200 220
FREQUENCY AT VCC (Hz)
–140
30600
30650
30700
VCC = 5V
1.0
0.8
VCC = 2.7V
0.4
0
–45 –30 –15
400
350
300
0 15 30 45 60
TEMPERATURE (°C)
75
90
2498 G25
VCC = 2.7V
140
120
0 15 30 45 60
TEMPERATURE (°C)
2
VCC = 5V
200
100
90
10
20
OUTPUT DATA RATE (READINGS/SEC)
30
2498 G26
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
fO = GND
1
0
25°C, 90°C
–1
–2
VCC = 3V
0
75
2498 G24
3
250
150
0.2
VCC = 5V
Integral Nonlinearity (2x Speed
Mode; VCC = 5V, VREF = 5V)
VREF = VCC
IN+ = GND
IN– = GND
SCK = NC
SDO = NC
SDI = GND
CS GND
fO = EXT OSC
TA = 25°C
450
SUPPLY CURRENT (µA)
SLEEP MODE CURRENT (µA)
500
1M
160
Conversion Current
vs Output Data Rate
2.0
0.6
180
fO = GND
CS = GND
SCK = NC
SDO = NC
SDI = GND
2498 G23
Sleep Mode Current
vs Temperature
1.2
10k 100k
1k
100
FREQUENCY AT VCC (Hz)
100
–45 –30 –15
30800
30750
FREQUENCY AT VCC (Hz)
2498 G22
fO = GND
1.8 CS = VCC
SCK = NC
1.6
SDO = NC
1.4 SDI = GND
10
Conversion Current
vs Temperature
CONVERSION CURRENT (µA)
–80
1
2498 G21
0
VCC = 4.1V DC ±1.4V
VREF = 2.5V
IN+ = GND
IN– = GND
fO = GND
TA = 25°C
–60
–140
–140
PSRR vs Frequency at VCC
REJECTION (dB)
REJECTION (dB)
–40
5.5
2498 G20
PSRR vs Frequency at VCC
–20
–80
–120
2498 G19
0
–60
–100
300
90
VCC = 4.1V DC
VREF = 2.5V
IN+ = GND
IN– = GND
fO = GND
TA = 25°C
–40
302
0 15 30 45 60
TEMPERATURE (°C)
PSRR vs Frequency at VCC
–20
INL (ppm OF VREF)
302
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
fO = GND
TA = 25°C
308
FREQUENCY (kHz)
FREQUENCY (kHz)
308
0
REJECTION (dB)
310
On-Chip Oscillator Frequency
vs VCC
–45°C
–3
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
2
2.5
2498 G27
2498fg
8
For more information www.linear.com/LTC2498
LTC2498
Typical Performance Characteristics
1
0
–45°C, 25°C
–2
1
90°C
0
–45°C, 25°C
–1
–0.75
–0.25
0.25
0.75
INPUT VOLTAGE (V)
–3
–1.25
1.25
6
4
–0.75
200
OFFSET ERROR (µV)
0.4
VCC = 5V
VIN = 0V
VIN(CM) = GND
fO = GND
TA = 25°C
1
0
240
194
192
190
188
186
180
5
–1
240
1
0
3
VIN(CM) (V)
2
4
220
0
4.5
5
5.5
–40
210
200
190
2498 G34
160
90
VCC = 4.1V DC
REF+ = 2.5V
REF– = GND
IN+ = GND
IN– = GND
fO = GND
TA = 25°C
–20
–60
–80
–100
–120
170
4
3.5
VCC (V)
75
PSRR vs Frequency at VCC
(2x Speed Mode)
180
50
0 15 30 45 60
TEMPERATURE (°C)
2498 G33
REJECTION (dB)
OFFSET ERROR (µV)
100
3
160
–45 –30 –15
6
5
VCC = 5V
VIN = 0V
VIN(CM) = GND
fO = GND
TA = 25°C
230
150
2.5
190
Offset Error vs VREF
(2x Speed Mode)
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
fO = GND
TA = 25°C
2
200
2498 G32
Offset Error vs VCC
(2x Speed Mode)
200
210
170
2498 G31
250
220
180
182
4
188.6
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
fO = GND
230
184
3
2
VREF (V)
183.8
186.2
OUTPUT READING (µV)
2498 G30
OFFSET ERROR (µV)
196
0.8
0.6
181.4
Offset Error vs Temperature
(2x Speed Mode)
VCC = 5V
VREF = 5V
VIN = 0V
fO = GND
TA = 25°C
198
0.2
0
179
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
Offset Error vs VIN(CM)
(2x Speed Mode)
1.0
RMS NOISE (µV)
8
2498 G29
RMS Noise vs VREF
(2x Speed Mode)
0
RMS = 0.85µV
10,000 CONSECUTIVE
AVERAGE = 0.184mV
14 READINGS
VCC = 5V
12 VREF = 5V
VIN = 0V
GAIN = 256
10
TA = 25°C
2
2498 G28
OFFSET ERROR (µV)
16
–2
–3
–1.25
0
Noise Histogram
(2x Speed Mode)
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
fO = GND
2
90°C
–1
Integral Nonlinearity (2x Speed
Mode; VCC = 2.7V, VREF = 2.5V)
NUMBER OF READINGS (%)
2
INL (ppm OF VREF)
3
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
fO = GND
INL (ppm OF VREF)
3
Integral Nonlinearity (2x Speed
Mode; VCC = 5V, VREF = 2.5V)
0
1
2
3
VREF (V)
4
5
2498 G35
–140
1
10
10k 100k
1k
100
FREQUENCY AT VCC (Hz)
1M
2498 G36
2498fg
For more information www.linear.com/LTC2498
9
LTC2498
Typical Performance Characteristics
PSRR vs Frequency at VCC
(2x Speed Mode)
PSRR vs Frequency at VCC
(2x Speed Mode)
RREJECTION (dB)
–20
–40
–60
0
VCC = 4.1V DC ±1.4V
REF+ = 2.5V
REF– = GND
IN+ = GND
IN– = GND
fO = GND
TA = 25°C
–80
–100
–80
–100
–120
–140
VCC = 4.1V DC ±0.7V
REF+ = 2.5V
REF– = GND
IN+ = GND
–40 IN– = GND
fO = GND
–60 TA = 25°C
–20
REJECTION (dB)
0
–120
0 20 40 60 80 100 120 140 160 180 200 220
FREQUENCY AT VCC (Hz)
–140
30600
30650
30700
30750
FREQUENCY AT VCC (Hz)
2498 G37
30800
2498 G38
Pin Functions
GND (Pins 1, 3, 4, 5, 6, 31, 32, 33): Ground. Multiple
ground pins internally connected for optimum ground current flow and VCC decoupling. Connect each one of these
pins to a common ground plane through a low impedance
connection. All eight pins must be connected to ground
for proper operation.
ADCINP (Pin 25): Positive ADC Input. Tie to the output
of a buffer/amplifier driven by MUXOUTP or tie directly
to MUXOUTP.
NC (Pin 2): No Connection. This pin can be left floating
or tied to GND.
MUXOUTN (Pin 27): Negative Multiplexer Output. Used
to drive an external buffer/amplifier or can be shorted
directly to ADCINN.
COM (Pin 7): The Common Negative Input (IN–) for All
Single-Ended Multiplexer Configurations. The voltage on
CH0 to CH15 and COM pins can have any value between
GND – 0.3V to VCC + 0.3V. Within these limits, the two
selected inputs (IN+ and IN–) provide a bipolar input range
(VIN = IN+ – IN–) from –0.5 • VREF to 0.5 • VREF. Outside
this input range, the converter produces unique over-range
and under-range output codes.
CH0 to CH15 (Pins 8 to 23): Analog Inputs. May be programmed for single-ended or differential mode.
MUXOUTP (Pin 24): Positive Multiplexer Output. Used
to drive an external buffer/amplifier or can be shorted
directly to ADCINP.
ADCINN (Pin 26): Negative ADC Input. Tie to the output
of a buffer/amplifier driven by MUXOUTN or tie directly
to MUXOUTN.
VCC (Pin 28): Positive Supply Voltage. Bypass to GND with
a 10µF tantalum capacitor in parallel with a 0.1µF ceramic
capacitor as close to the part as possible.
REF+ (Pin 29), REF– (Pin 30): Differential Reference Input.
The voltage on these pins can have any value between
GND and VCC as long as the reference positive input, REF+,
remains more positive than the negative reference input,
REF–, by at least 0.1V. The differential voltage (REF = REF+
– REF–) sets the full-scale range for all input channels.
When performing an on-chip temperature measurement,
the minimum value of REF = 2V.
2498fg
10
For more information www.linear.com/LTC2498
LTC2498
Pin Functions
SDI (Pin 34): Serial Data Input. This pin is used to select the
line frequency rejection mode, 1x or 2x mode, temperature
sensor, as well as the input channel. The serial data input
is applied under control of the serial clock (SCK) during
the data output/input operation. The first conversion following a new input or mode change is valid.
fO (Pin 35): Frequency Control Pin. Digital input that
controls the internal conversion clock rate. When fO is
connected to VCC or GND, the converter uses its internal
oscillator running at 307.2kHz. The conversion clock may
also be overridden by driving the fO pin with an external
clock in order to change the output rate and the digital
filter rejection null.
CS (Pin 36): Active LOW Chip Select. A LOW on this pin
enables the digital input/output and wakes up the ADC.
Following each conversion, the ADC automatically enters
the Sleep mode and remains in this low power state as
long as CS is HIGH. A LOW-to-HIGH transition on CS
during the Data Output aborts the data transfer and starts
a new conversion.
SDO (Pin 37): Three-State Digital Output. During the data
output period, this pin is used as the serial data output.
When the chip select pin is HIGH, the SDO pin is in a high
impedance state. During the conversion and sleep periods,
this pin is used as the conversion status output. When
the conversion is in progress this pin is HIGH; once the
conversion is complete SDO goes LOW. The conversion
status is monitored by pulling CS LOW.
SCK (Pin 38): Bidirectional, Digital I/O, Clock Pin. In Internal
Serial Clock Operation mode, SCK is generated internally
and is seen as an output on the SCK pin . In External Serial
Clock Operation mode, the digital I/O clock is externally
applied to the SCK pin. The Serial Clock operation mode
is determined by the logic level applied to the SCK pin at
power-up and during the most recent falling edge of CS.
Exposed Pad (Pin 39): Ground. This pin is ground and
must be soldered to the PCB ground plane. For prototyping
purposes, this pin may remain floating.
2498fg
For more information www.linear.com/LTC2498
11
LTC2498
Functional Block Diagram
TEMP
SENSOR
VCC
INTERNAL
OSCILLATOR
MUXOUTP ADCINP
GND
CH0
CH1
CH15
COM
–
•
•
•
fO
(INT/EXT)
AUTOCALIBRATION
AND CONTROL
REF+
REF–
+
DIFFERENTIAL
3RD ORDER
ΔΣ MODULATOR
MUX
SDI
SCK
SDO
CS
SERIAL
INTERFACE
DECIMATING FIR
ADDRESS
2498 BD
MUXOUTN ADCINN
Figure 1. Functional Block Diagram
Test Circuits
VCC
SDO
1.69k
1.69k
Hi-Z TO VOH
VOL TO VOH
VOH TO Hi-Z
CLOAD = 20pF
SDO
CLOAD = 20pF
2498 TC01
Hi-Z TO VOL
VOH TO VOL
VOL TO Hi-Z
2498 TC02
2498fg
12
For more information www.linear.com/LTC2498
LTC2498
timing diagrams
Timing Diagram Using Internal SCK (SCK HIGH with CS↓)
CS
t1
t2
SDO
tKQMIN
t3
tKQMAX
SCK
t7
t8
SDI
2498 TD01
SLEEP
DATA IN/OUT
CONVERSION
Timing Diagram Using External SCK (SCK LOW with CS↓)
CS
t1
t2
SDO
t5
SCK
tKQMIN
t6
t4
t7
tKQMAX
t8
SDI
2498 TD02
SLEEP
DATA IN/OUT
CONVERSION
2498fg
For more information www.linear.com/LTC2498
13
LTC2498
Applications Information
Converter Operation
Converter Operation Cycle
The LTC2498 is a multi-channel, low power, delta-sigma
analog-to-digital converter with an easy to use 4-wire interface and automatic differential input current cancellation.
Its operation is made up of three states (See Figure 2).
The converter operating cycle begins with the conversion,
followed by the sleep state and ends with the data input/
output cycle. The 4-wire interface consists of serial data
output (SDO), serial clock (SCK), chip select (CS) and
serial data input (SDI).The interface, timing, operation
cycle, and data output format is compatible with Linear’s
entire family of ΔΣ converters.
Initially, at power-up, the LTC2498 performs a conversion.
Once the conversion is complete, the device enters the
sleep state. While in this sleep state, if CS in HIGH, power
consumption is reduced by two orders of magnitude. The
part remains in the sleep state as long as CS is HIGH. The
conversion result is held indefinitely in a static shift register
while the part is in the sleep state.
Once CS is pulled LOW, the device powers up, exits the
sleep mode, and enters the data input/output state. If CS
is brought HIGH before the first rising edge of SCK, the
device returns to the sleep state and the power is reduced.
If CS is brought HIGH after the first rising edge of SCK, the
POWER UP
IN+= CH0, IN–= CH1
50/60Hz,1X
data output cycle is aborted and a new conversion cycle
begins. The data output corresponds to the conversion
just completed. This result is shifted out on the serial data
output pin (SDO) under the control of the serial clock pin
(SCK). Data is updated on the falling edge of SCK allowing
the user to reliably latch data on the rising edge of SCK (See
Figure 3). The configuration data for the next conversion
is also loaded into the device at this time. Data is loaded
from the serial data input pin (SDI) on each rising edge
of SCK. The data input/output cycle is concluded once 32
bits are read out of the ADC or when CS is brought HIGH.
The device automatically initiates a new conversion and
the cycle repeats.
Through timing control of the CS and SCK pins, the LTC2498
offers several flexible modes of operation (internal or
external SCK and free-running conversion modes). These
various modes do not require programming and do not
disturb the cyclic operation described above. These modes
of operation are described in detail in the Serial Interface
Timing Modes section.
Ease of Use
The LTC2498 data output has no latency, filter settling
delay or redundant data associated with the conversion
cycle. There is a one-to-one correspondence between the
conversion and the output data. Therefore, multiplexing
multiple analog inputs is straightforward. Each conversion,
immediately following a newly selected input or mode, is
valid and accurate to the full specifications of the device.
The LTC2498 automatically performs offset and full scale
calibration every conversion cycle independent of the
input channel selected. This calibration is transparent to
the user and has no effect with the operation cycle described above. The advantage of continuous calibration
is extreme stability of offset and full-scale readings with
respect to time, supply voltage variation, input channel,
and temperature drift.
CONVERT
SLEEP
CS = LOW
AND
SCK
Easy Drive Input Current Cancellation
CHANNEL SELECT
CONFIGURATION SELECT
DATA OUTPUT
2498 F02
Figure 2. LTC2498 State Transition Diagram
The LTC2498 combines a high precision delta-sigma ADC
with an automatic, differential, input current cancellation
front end. A proprietary front end passive sampling network
transparently removes the differential input current. This
2498fg
14
For more information www.linear.com/LTC2498
LTC2498
Applications Information
enables external RC networks and high impedance sensors to directly interface to the LTC2498 without external
amplifiers. The remaining common mode input current
is eliminated by either balancing the differential input
impedances or setting the common mode input equal
to the common mode reference (see the Automatic Differential Input Current Cancellation section). This unique
architecture does not require on-chip buffers thereby
enabling signals to swing beyond ground or up to VCC.
Moreover, the cancellation does not interfere with the
transparent offset and full-scale auto-calibration and the
absolute accuracy (full-scale + offset + linearity + drift) is
maintained even with external RC networks.
Power-Up Sequence
The LTC2498 automatically enters an internal reset state
when the power supply voltage VCC drops below approximately 2V. This feature guarantees the integrity of
the conversion result, input channel selection, and serial
clock mode.
When VCC rises above this threshold, the converter creates
an internal power-on reset (POR) signal with a duration
of approximately 4ms. The POR signal clears all internal
registers. The conversion immediately following a POR
cycle is performed on the input channel IN+ = CH0, IN– =
CH1, simultaneous 50Hz/60Hz rejection and 1x output
rate. The first conversion following a POR cycle is accurate
within the specification of the device if the power supply
voltage is restored to (2.7V to 5.5V) before the end of the
POR interval. A new input channel, rejection mode, speed
mode, or temperature selection can be programmed into
the device during this first data input/output cycle.
Reference Voltage Range
This converter accepts a truly differential external reference
voltage. The absolute/common mode voltage range for
REF+ and REF– pins covers the entire operating range of
the device (GND to VCC). For correct converter operation,
VREF must be positive (REF+ > REF–)
The LTC2498 differential reference input range is 0.1V to
VCC. For the simplest operation, REF+ can be shorted to
VCC and REF– can be shorted to GND. The converter output noise is determined by the thermal noise of the front
end circuits, and as such, its value in nanovolts is nearly
constant with reference voltage. A decrease in reference
voltage will not significantly improve the converter’s effective resolution. On the other hand, a decreased reference
will improve the converter’s overall INL performance.
Input Voltage Range
The LTC2498 input measurement range is –0.5 • VREF
to +0.5 • VREF in both differential and single-ended
configurations as shown in Figure 39. Highest linearity
is achieved with fully differential drive and a constant
common-mode voltage (Figure 39b). Other drive schemes
may incur an INL error of approximately 50ppm. This error
can be calibrated out using a three point calibration and a
second-order curve fit.
The analog input is truly differential with an absolute, common mode range for CH0 to CH15 and COM input pins
extending from GND – 0.3V to VCC + 0.3V. Outside these
limits, the ESD protection devices begin to turn on and the
errors due to input leakage current increase rapidly. Within
these limits, the LTC2498 converts the bipolar differential
input signal VIN = IN+ – IN– (where IN+ and IN– are the
selected input channels), from –FS = –0.5 • VREF to +FS =
0.5 • VREF where VREF = REF+ – REF–. Outside this range,
the converter indicates the overrange or the underrange
condition using distinct output codes.
Signals applied to the input (CH0 to CH15, COM) may
extend 300mV below ground and above VCC. In order to
limit any fault current, resistors of up to 5k may be added
in series with the input. The effect of series resistance on
the converter accuracy can be evaluated from the curves
presented in the Input Current/Reference Current sections.
In addition, series resistors will introduce a temperature
dependent error due to input leakage current. A 1nA input
leakage current will develop a 1ppm offset error on a 5k
resistor if VREF = 5V. This error has a very strong temperature dependency.
MUXOUT/ADCIN
The output of the multiplexer (MUXOUT) and the input
to the ADC (ADCIN) can be used to perform input signal
conditioning on any of the selected input channels or simply
shorted together for direct digitization. If an external ampli2498fg
For more information www.linear.com/LTC2498
15
LTC2498
Applications Information
fier is used, the LTC2498 automatically calibrates both the
offset and drift of this circuit and the Easy Drive sampling
scheme enables a wide variety of amplifiers to be used.
In order to achieve optimum performance, if an external
amplifier is not used, short these pins directly together
(ADCINP to MUXOUTP and ADCINN to MUXOUTN) and
minimize their capacitance to ground.
Serial Interface Pins
The LTC2498 transmits the conversion result, reads the
input configuration, and receives a start of conversion
command through a synchronous 3- or 4-wire interface.
During the conversion and sleep states, this interface
can be used to access the converter status. During the
data output state, it is used to read the conversion result,
program the input channel, rejection frequency, speed
multiplier, and select the temperature sensor.
Serial Clock Input/Output (SCK)
The serial clock pin (SCK) is used to synchronize the data
input/output transfer. Each bit is shifted out of the SDO
pin on the falling edge of SCK and data is shifted into the
SDI pin on the rising edge of SCK.
The serial clock pin (SCK) can be configured as either a
master (SCK is an output generated internally) or a slave
(SCK is an input and applied externally). Master mode
(internal SCK) is selected by simply floating the SCK pin.
Slave mode (external SCK) is selected by driving SCK LOW
during power-up and each falling edge of CS. Specific
details of these SCK modes are described in the Serial
Interface Timing Modes section.
Serial Data Output (SDO)
The serial data output pin (SDO) provides the result of the
last conversion as a serial bit stream (MSB first) during
the data output state. In addition, the SDO pin is used as
an end of conversion indicator during the conversion and
sleep states.
When CS is HIGH, the SDO driver is switched to a high
impedance state in order to share the data output line with
other devices. If CS is brought LOW during the conversion
phase, the EOC bit (SDO pin) will be driven HIGH. Once
the conversion is complete, if CS is brought LOW, EOC
will be driven LOW indicating the conversion is complete
and the result is ready to be shifted out of the device.
Chip Select (CS)
The active low CS pin is used to test the conversion status,
enable I/O data transfer, initiate a new conversion, control
the duration of the sleep state, and set the SCK mode.
At the conclusion of a conversion cycle, while CS is HIGH,
the device remains in a low power sleep state where the
supply current is reduced several orders of magnitude. In
order to exit the sleep state and enter the data output state,
CS must be pulled LOW. Data is now shifted out the SDO
pin under control of the SCK pin as described previously.
A new conversion cycle is initiated either at the conclusion
of the data output cycle (all 32 data bits read) or by pulling
CS HIGH any time between the first and 32nd rising edges
of the serial clock (SCK). In this case, the data output is
aborted and a new conversion begins.
Serial Data Input (SDI)
The serial data input (SDI) is used to select the input
channel, rejection frequency, speed multiplier and to access the integrated temperature sensor. Data is shifted
into the device during the data output/input state on the
rising edge of SCK while CS is LOW.
OUTPUT DATA FORMAT
The LTC2498 serial output stream is 32 bits long. The
first bit indicates the conversion status, the second bit is
always zero, and the third bit conveys sign information.
The next 24 bits are the conversion result, MSB first. The
remaining 5 bits are sub LSBs beyond the 24-bit level
that may be included in averaging or discarded without
loss of resolution.
Bit 31 (first output bit) is the end of conversion (EOC)
indicator. This bit is available on the SDO pin during the
conversion and sleep states whenever CS is LOW. This
bit is HIGH during the conversion cycle, goes LOW once
the conversion is complete, and is Hi-Z when CS is HIGH.
Bit 30 (second output bit) is a dummy bit (DMY) and is
always LOW.
2498fg
16
For more information www.linear.com/LTC2498
LTC2498
Applications Information
Bit 29 (third output bit) is the conversion result sign
indicator (SIG). If the selected input (VIN = IN+ – IN–) is
greater than 0V, this bit is HIGH. If VIN < 0, this bit is LOW.
Data is shifted out of the SDO pin under control of the
serial clock (SCK), see Figure 3. Whenever CS is HIGH,
SDO remains high impedance and SCK is ignored.
Bit 28 (fourth output bit) is the most significant bit (MSB)
of the result. This bit in conjunction with Bit 29 also provides underrange and overrange indication. If both Bit 29
and Bit 28 are HIGH, the differential input voltage is above
+FS. If both Bit 29 and Bit 28 are LOW, the differential
input voltage is below –FS. The function of these bits is
summarized in Table 1.
In order to shift the conversion result out of the device,
CS must first be driven LOW. EOC is seen at the SDO pin
of the device once CS is pulled LOW. EOC changes in real
time from HIGH to LOW at the completion of a conversion.
This signal may be used as an interrupt for an external
microcontroller. Bit 31 (EOC) can be captured on the first
rising edge of SCK. Bit 30 is shifted out of the device on
the first falling edge of SCK. The final data bit (Bit 0) is
shifted out on the on the falling edge of the 31st SCK and
may be latched on the rising edge of the 32nd SCK pulse.
On the falling edge of the 32nd SCK pulse, SDO goes HIGH
indicating the initiation of a new conversion cycle. This
bit serves as EOC (Bit 31) for the next conversion cycle.
Table 2 summarizes the output data format.
Table 1. LTC2498 Status Bits
Input Range
VIN ≥ 0.5 • VREF
Bit 31
EOC
Bit 30
DMY
Bit 29
SIG
Bit 28
MSB
0
0
1
1
0V ≤ VIN < 0.5 • VREF
0
0
1/0
0
–0.5 • VREF ≤ VIN < 0V
0
0
0
1
VIN < –0.5 • VREF
0
0
0
0
Bits 28 to 5 are the 24-bit conversion result MSB first.
Bit 5 is the least significant bit (LSB24).
Bits 4 to 0 are sub LSBs below the 24-bit level. Bits 4 to
0 may be included in averaging or discarded without loss
of resolution.
As long as the voltage on the IN+ and IN– pins remains between –0.3V and VCC + 0.3V (absolute maximum operating
range) a conversion result is generated for any differential
input voltage VIN from –FS = –0.5 • VREF to +FS = 0.5 •
VREF. For differential input voltages greater than +FS, the
conversion result is clamped to the value corresponding
to +FS + 1LSB. For differential input voltages below –FS,
the conversion result is clamped to the value –FS – 1LSB.
CS
1
2
3
4
5
1
0
EN
SGL
ODD
EOC
“0”
SIG
MSB
6
7
8
9
A2
A1
A0
EN2
10
11
12
13
14
32
SCK
(EXTERNAL)
SDI
SDO
DON'T CARE
Hi-Z
IM
FA
FB
SPD
DON'T CARE
Hi-Z
BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 BIT 24 BIT 23 BIT 22 BIT 21 BIT 20 BIT 19 BIT 18 BIT 17
CONVERSION
SLEEP
DATA INPUT/OUTPUT
BIT 0
CONVERSION
2498 F03
Figure 3. Channel Selection, Configuration Selection and Data Output Timing
2498fg
For more information www.linear.com/LTC2498
17
LTC2498
Applications Information
Table 2. Output Data Format
Differential Input Voltage
VIN*
Bit 31
EOC
Bit 30
DMY
Bit 29
SIG
Bit 28
MSB
Bit 27
Bit 26
Bit 25
…
Bit 0
VIN* ≥ 0.5 • VREF**
0
0
1
1
0
0
0
…
0
0.5 • VREF** – 1LSB
0
0
1
0
1
1
1
…
1
0.25 • VREF**
0
0
1
0
1
0
0
…
0
0.25 • VREF** – 1LSB
0
0
1
0
0
1
1
…
1
0
0
0
1/0***
0
0
0
0
…
0
–1LSB
0
0
0
1
1
1
1
…
1
–0.25 • VREF**
0
0
0
1
1
0
0
…
0
–0.25 • VREF** – 1LSB
0
0
0
1
0
1
1
…
1
–0.5 • VREF**
0
0
0
1
0
0
0
…
0
VIN* < –0.5 • VREF**
0
0
0
0
1
1
1
…
X****
*The differential input voltage VIN = IN+ – IN–. **The differential reference voltage VREF = REF+ – REF–.
***The sign bit changes state during the 0 output code when the device is operating in the 2x speed mode.
****The underrange code is OxOFFFFxxx in 2x mode.
Input Data Format
The LTC2498 serial input word is 13 bits long and contains
two distinct sets of data. The first set (SGL, ODD, A2, A1,
A0) is used to select the input channel. The second set of
data (IM, FA, FB, SPD) is used to select the frequency rejection, speed mode (1x, 2x), and temperature measurement.
After power-up, the device initiates an internal reset cycle
which sets the input channel to CH0 – CH1 (IN+ = CH0, IN– =
CH1), the frequency rejection to simultaneous 50Hz/60Hz,
and 1x output rate (auto-calibration enabled). The first
conversion automatically begins at power-up using this
default configuration. Once the conversion is complete,
a new word may be written into the device.
The first 3 bits shifted into the device consist of two preenable bits and one enable bit. As demonstrated in Figure 3,
the first three bits shifted into the device enable the device
configuration and input channel selection. Valid settings for
these three bits are 000, 100 and 101. Other combinations
should be avoided. If the first three bits are 000 or 100, the
following data is ignored (don’t care) and the previously
selected input channel and configuration remain valid for
the next conversion.
If the first 3 bits shifted into the device are 101, then the
next 5 bits select the input channel for the next conversion
cycle, see Table 3.
The first input bit following the 101 sequence (SGL)
determines if the input selection is differential (SGL = 0)
or single-ended (SGL = 1). For SGL = 0, two adjacent
channels can be selected to form a differential input. For
SGL = 1, one of 16 channels is selected as the positive
input. The negative input is COM for all single ended operations. The remaining 4 bits (ODD, A2, A1, A0) determine
which channel(s) is/are selected and the polarity (for a
differential input).
The next serial input bit immediately following the input
channel selection is the enable bit for the conversion
configuration (EN2). If this bit is set to 0, then the next
conversion is performed using the previously selected
converter configuration. This is useful in systems using
the same rejection/speed for all input channels and for
backward compatibility with the LTC2418/LTC2414 families
of delta sigma ADCs.
A new configuration can be loaded into the device by
setting EN2 = 1, see Table 4. The first bit (IM) is used
to select the internal temperature sensor. If IM = 1, the
following conversion will be performed on the internal
temperature sensor rather than the selected input channel.
The next 2 bits (FA and FB) are used to set the rejection
frequency. The final bit (SPD) is used to select either the
1x output rate if SPD = 0 (auto-calibration is enabled and
the offset is continuously calibrated and removed from
2498fg
18
For more information www.linear.com/LTC2498
LTC2498
Applications Information
Table 3. Channel Selection
MUX ADDRESS
ODD/
SGL SIGN
A2
A1
CHANNEL SELECTION
A0
0
1
IN+
IN–
*0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
1
1
0
0
1
0
0
0
0
1
0
1
0
0
1
1
0
0
0
1
1
1
0
1
0
0
0
0
1
0
0
1
0
1
0
1
0
0
1
0
1
1
0
1
1
0
0
0
1
1
0
1
0
1
1
1
0
0
1
1
1
1
1
0
0
0
0
1
0
0
0
1
1
0
0
1
0
1
0
0
1
1
1
0
1
0
0
1
0
1
0
1
1
0
1
1
0
1
0
1
1
1
1
1
0
0
0
1
1
0
0
1
1
1
0
1
0
1
1
0
1
1
1
1
1
0
0
1
1
1
0
1
1
1
1
1
0
1
1
1
1
IN–
2
3
IN+
IN–
4
5
IN+
IN–
6
7
IN+
IN–
8
9
IN+
IN–
10
11
IN+
IN–
12
13
IN+
IN–
14
15
IN+
IN–
IN–
IN+
COM
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
IN–
IN+
1
IN–
*Default at power-up
2498fg
For more information www.linear.com/LTC2498
19
LTC2498
Applications Information
Table 4. Converter Configuration
1
0
EN
SGL
ODD
A2
A1
A0
EN2
IM
FA
FB
SPD
CONVERTER CONFIGURATION
1
0
0
X
X
X
X
X
X
X
X
X
X
Keep Previous
1
0
1
X
X
X
X
X
0
X
X
X
X
Keep Previous (Change Channel)
0
0
0
X
X
X
X
X
X
X
X
X
X
Keep Previous
1
0
1
X
X
X
X
X
1
0
0
0
0
External Input (See Table 3)
50Hz/60Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
0
0
1
0
External Input (See Table 3)
50Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
0
1
0
0
External Input (See Table 3)
60Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
0
0
0
1
External Input (See Table 3)
50Hz/60Hz Rejection, 2x
1
0
1
X
X
X
X
X
1
0
0
1
1
External Input (See Table 3)
50Hz Rejection, 2x
1
0
1
X
X
X
X
X
1
1
0
0
X
Measure Temperature
50Hz/60Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
1
0
1
X
Measure Temperature
50Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
1
1
0
X
Measure Temperature
60Hz Rejection, 1x
the final conversion result) or the 2x output rate if SPD
= 1 (offset calibration disabled, multiplexing output rates
up to 15Hz with no latency). When IM = 1 (temperature
measurement), SPD will be ignored and the device will
operate in 1x mode. The configuration remains valid until
a new input word with EN = 1 (the first 3 bits are 101) and
EN2 = 1 is shifted into the device.
2x mode (SPD = 1), the linearity and full-scale errors are
unchanged from the 1x mode performance. In both the 1x
and 2x mode there is no latency. This enables input steps
or multiplexer changes to settle in a single conversion
cycle easing system overhead and increasing the effective
conversion rate. During temperature measurements, the
1x mode is always used independent of the value of SPD.
Rejection Mode (FA, FB)
Temperature Sensor
The LTC2498 includes a high accuracy on-chip oscillator
with no required external components. Coupled with an
integrated 4th order digital lowpass filter, the LTC2498
rejects line frequency noise. In the default mode, the
LTC2498 simultaneously rejects 50Hz and 60Hz by at least
87dB. If more rejection is required, the LTC2498 can be
configured to reject 50Hz or 60Hz to better than 110dB.
The LTC2498 includes an integrated temperature sensor.
The temperature sensor is selected by setting IM = 1.
During temperature readings, MUXOUTN/MUXOUTP
remains connected to the selected input channel. The
ADC internally connects to the temperature sensor and
performs a conversion.
Speed Mode (SPD)
Every conversion cycle, two conversions are combined to
remove the offset (default mode). This result is free from
offset and drift. In applications where the offset is not
critical, the auto-calibration feature can be disabled with
the benefit of twice the output rate. While operating in the
The digital output is proportional to the absolute temperature of the device. This feature allows the converter
to perform cold junction compensation for external
thermocouples or continuously remove the temperature
effects of external sensors.
The internal temperature sensor output is 28mV at 27°C
(300°K), with a slope of 93.5µV/°C independent of VREF.
2498fg
20
For more information www.linear.com/LTC2498
LTC2498
Applications Information
Slope calibration is not required if the reference voltage (VREF) is known. A 5V reference has a slope of 314
LSBs24/°C. The temperature is calculated from the output
code (DATAOUT24) for a 5V reference using the following
formula:
TK = DATAOUT24/314 in Kelvin
If a different value of VREF is used, the temperature output is:
DATAOUT24 • VREF
TK =
in Kelvin
1570
If the value of VREF is not known, the slope is determined by
measuring the temperature sensor at a known temperature
TN (in °K) and using the following formula:
SLOPE = DATAOUT24/TN
This value of slope can be used to calculate further temperature readings using:
All Kelvin temperature readings can be converted to TC
(°C) using the fundamental equation:
TC = TK – 273
Serial Interface Timing Modes
The LTC2498’s 4-wire interface is SPI and MICROWIRE
compatible. This interface offers several flexible modes
of operation. These include internal/external serial clock,
3- or 4-wire I/O, single cycle or continuous conversion. The
following sections describe each of these timing modes
in detail. In all cases, the converter can use the internal
oscillator (fO = LOW or fO = HIGH) or an external oscillator
connected to the fO pin. For each mode, the operating cycle,
data input format, data output format, and performance
remain the same. Refer to Table 5 for a summary.
TK = DATAOUT24/SLOPE
140000
5
VCC = 5V
VREF = 5V
120000 SLOPE = 314 LSB /K
24
4
ABSOLUTE ERROR (°C)
3
DATAOUT24
100000
80000
60000
40000
1
0
–1
–2
–3
20000
0
2
–4
0
100
200
300
TEMPERATURE (°K)
–5
–55
400
–30
2498 F04
Figure 4. Internal PTAT Digital Output vs Temperature
–5
20
45
70
TEMPERATURE (°C)
95
120
2498 F05
Figure 5. Absolute Temperature Error
Table 5. LTC2498 Interface Timing Modes
CONFIGURATION
SCK
CONVERSION
DATA OUTPUT CONNECTION AND
SOURCE CYCLE CONTROL
CONTROL
WAVEFORMS
External SCK, Single Cycle
Conversion
External
CS and SCK
CS and SCK
Figures 6, 7
External SCK, 3-Wire I/O
External
SCK
SCK
Figure 8
Internal SCK, Single Cycle
Conversion
Internal
CS↓
CS↓
Figures 9, 10
Internal SCK, 3-Wire I/O,
Continuous Conversion
Internal
Continuous
Internal
Figure 11
2498fg
For more information www.linear.com/LTC2498
21
LTC2498
Applications Information
External Serial Clock, Single Cycle Operation
When the device is in the sleep state, its conversion result
is held in an internal static shift register. The device remains in the sleep state until the first rising edge of SCK
is seen while CS is LOW. The input data is then shifted
in via the SDI pin on each rising edge of SCK (including
the first rising edge). The channel selection and converter
configuration mode will be used for the following conversion cycle. If the input channel or converter configuration
is changed during this I/O cycle, the new settings take
effect on the conversion cycle following the data input/
output cycle. The output data is shifted out the SDO pin
on each falling edge of SCK. This enables external circuitry
to latch the output on the rising edge of SCK. EOC can be
latched on the first rising edge of SCK and the last bit of
the conversion result can be latched on the 32nd rising
edge of SCK. On the 32nd falling edge of SCK, the device
begins a new conversion and SDO goes HIGH (EOC = 1)
indicating a conversion is in progress.
This timing mode uses an external serial clock to shift out
the conversion result and CS to monitor and control the
state of the conversion cycle, see Figure 6.
The external serial clock mode is selected during the powerup sequence and on each falling edge of CS. In order to
enter and remain in the external SCK mode of operation,
SCK must be driven LOW both at power-up and on each
CS falling edge. If SCK is HIGH on the falling edge of CS,
the device will switch to the internal SCK mode.
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
While CS is LOW, EOC is output to the SDO pin.
EOC = 1 while a conversion is in progress and EOC = 0 if
the conversion is complete and the device is in the sleep
state. Independent of CS, the device automatically enters
the sleep state once the conversion is complete; however,
in order to reduce the power, CS must be HIGH.
At the conclusion of the data cycle, CS may remain LOW
and EOC monitored as an end-of-conversion interrupt.
2.7V TO 5.5V
10µF
28
VCC
= EXTERNAL OSCILLATOR
= INTERNAL OSCILLATOR
35
LTC2498
0.1µF
29
REFERENCE
VOLTAGE
0.1V TO VCC
30
8
•
•
•
ANALOG
INPUTS
fO
15
16
•
•
•
23
7
REF+
REF–
SDI
SCK
CH0
•
•
•
CH7
SDO
CH8
•
CS
34
38
4-WIRE
SPI INTERFACE
37
36
•
•
CH15
COM
GND
1,3,4,5,6,31,32,33,39
CS
1
2
3
4
5
6
7
8
9
1
0
EN
SGL
ODD
A2
A1
A0
EN2
EOC
“0”
SIG
MSB
10
11
12
13
14
32
SCK
(EXTERNAL)
SDI
SDO
DON'T CARE
Hi-Z
IM
FA
SLEEP
SPD
DON'T CARE
Hi-Z
BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 BIT 24 BIT 23 BIT 22 BIT 21
CONVERSION
FB
BIT 20 BIT 19
DATA INPUT/OUTPUT
BIT 18 BIT 17
BIT 0
CONVERSION
2498 F06
Figure 6. External Serial Clock, Single Cycle Operation
2498fg
22
For more information www.linear.com/LTC2498
LTC2498
Applications Information
Typically, CS remains LOW during the data output/input
state. However, the data output state may be aborted by
pulling CS HIGH any time between the 1st falling edge
and the 32nd falling edge of SCK, see Figure 7. On the
rising edge of CS, the device aborts the data output state
and immediately initiates a new conversion. In order to
program a new input channel, 8 SCK clock pulses are
required. If the data output sequence is aborted prior to
the 8th falling edge of SCK, the new input data is ignored
and the previously selected input channel remains valid.
If the rising edge of CS occurs after the 8th falling edge
of SCK, the new input channel is loaded and valid for the
next conversion cycle. If CS goes HIGH between the 8th
falling edge and the 16th falling edge of SCK, the new
channel is still loaded, but the converter configuration
remains unchanged. In order to program both the input
channel and converter configuration, CS must go HIGH
after the 16th falling edge of SCK (at this point all data
has been shifted into the device).
External Serial Clock, 3-Wire I/O
This timing mode uses a 3-wire serial I/O interface. The
conversion result is shifted out of the device by an externally
generated serial clock (SCK) signal, see Figure 8. CS is
permanently tied to ground, simplifying the user interface
or isolation barrier.
The external serial clock mode is selected at the end of the
power-on reset (POR) cycle. The POR cycle is typically
concluded 4ms after VCC exceeds 2V. The level applied
to SCK at this time determines if SCK is internally generated or externally applied. In order to enter the external
SCK mode, SCK must be driven LOW prior to the end of
the POR cycle.
Since CS is tied LOW, the end-of-conversion (EOC) can be
continuously monitored at the SDO pin during the convert
and sleep states. EOC may be used as an interrupt to an
external controller. EOC = 1 while the conversion is in
2.7V TO 5.5V
10µF
28
VCC
fO
= EXTERNAL OSCILLATOR
= INTERNAL OSCILLATOR
35
LTC2498
0.1µF
29
REFERENCE
VOLTAGE
0.1V TO VCC
30
8
•
•
•
ANALOG
INPUTS
15
16
•
•
•
23
7
REF+
REF–
SDI
SCK
CH0
•
•
•
CH7
SDO
CH8
•
CS
34
38
4-WIRE
SPI INTERFACE
37
36
•
•
CH15
COM
GND
1,3,4,5,6,31,32,33,39
CS
1
2
3
4
5
6
7
8
1
0
EN
SGL
ODD
A2
A1
A0
EOC
“0”
SIG
MSB
SCK
(EXTERNAL)
SDI
DON'T CARE
SDO
Hi-Z
BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 BIT 24
CONVERSION
SLEEP
DON'T CARE
DATA INPUT/OUTPUT
BIT 23
CONVERSION
SLEEP
2498 F07
Figure 7. External Serial Clock, Reduced Output Data Length and Valid Channel Selection
2498fg
For more information www.linear.com/LTC2498
23
LTC2498
Applications Information
10µF
2.7V TO 5.5V
28
0.1µF
VCC
fO
= EXTERNAL OSCILLATOR
= INTERNAL OSCILLATOR
35
LTC2498
REFERENCE
VOLTAGE
0.1V TO VCC
REF+
30
–
8
•
•
•
ANALOG
INPUTS
29
15
16
•
•
•
23
7
REF
SDI
SCK
CH0
•
•
•
CH7
SDO
CH8
•
CS
34
38
3-WIRE
SPI INTERFACE
37
36
•
•
CH15
COM
GND
1,3,4,5,6,31,32,33,39
CS
1
2
3
4
5
6
7
8
9
1
0
EN
SGL
ODD
A2
A1
A0
EN2
EOC
“0”
SIG
MSB
10
11
12
13
14
32
SCK
(EXTERNAL)
SDI
DON'T CARE
SDO
IM
FA
BIT 31 BIT 30 BIT 29 BIT 28 BIT 27 BIT 26 BIT 25 BIT 24 BIT 23 BIT 22 BIT 21
CONVERSION
FB
SPD
BIT 20 BIT 19
DATA INPUT/OUTPUT
SLEEP
DON'T CARE
BIT 18 BIT 17
BIT 0
CONVERSION
2498 F08
Figure 8. External Serial Clock, 3-Wire Operation (CS = 0)
progress and EOC = 0 once the conversion is complete.
On the falling edge of EOC, the conversion result is loading into an internal static shift register. The output data
can now be shifted out the SDO pin under control of the
externally applied SCK signal. Data is updated on the falling edge of SCK. The input data is shifted into the device
through the SDI pin on the rising edge of SCK. On the
32nd falling edge of SCK, SDO goes HIGH, indicating a
new conversion has begun. This data now serves as EOC
for the next conversion.
Internal Serial Clock, Single Cycle Operation
This timing mode uses the internal serial clock to shift out
the conversion result and CS to monitor and control the
state of the conversion cycle, see Figure 9.
In order to select the internal serial clock timing mode,
the serial clock pin (SCK) must be floating or pulled HIGH
before the conclusion of the POR cycle and prior to each
falling edge of CS. An internal weak pull-up resistor is active
on the SCK pin during the falling edge of CS; therefore,
the internal SCK mode is automatically selected if SCK is
not externally driven.
24
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may
be pulled LOW in order to monitor the state of the converter. Once CS is pulled LOW, SCK goes LOW and EOC
is output to the SDO pin. EOC = 1 while the conversion is
in progress and EOC = 0 if the device is in the sleep state
When testing EOC, if the conversion is complete (EOC =
0), the device will exit sleep state. In order to return to the
sleep state and reduce the power consumption, CS must be
pulled HIGH before the device pulls SCK HIGH. When the
device is using its own internal oscillator (fO is tied LOW),
the first rising edge of SCK occurs 12µs (tEOCTEST = 12µs)
after the falling edge of CS. If fO is driven by an external
oscillator of frequency fEOSC, then tEOCTEST = 3.6/fEOSC.
If CS remains LOW longer than tEOCTEST, the first rising
edge of SCK will occur and the conversion result is shifted
out the SDO pin on the falling edge of SCK. The serial
input word (SDI) is shifted into the device on the rising
edge of SCK.
After the 32nd rising edge of SCK a new conversion automatically begins. SDO goes HIGH (EOC = 1) and SCK
For more information www.linear.com/LTC2498
2498fg
LTC2498
Applications Information
10µF
2.7V TO 5.5V
28
VCC
= EXTERNAL OSCILLATOR
= INTERNAL OSCILLATOR
35
fO
LTC2498
0.1µF
REFERENCE
VOLTAGE
0.1V TO VCC
REF+
SDI
30
REF–
SCK
8
•
•
•
15
16
ANALOG
INPUTS
•
•
•
23
7
1µF
Figure 20. Input Normal Mode Rejection, Internal Oscillator
and 60Hz Rejection Mode
2498fg
For more information www.linear.com/LTC2498
31
LTC2498
Applications Information
noise to 15dB (see Figure 22), if noise sources are present
at these frequencies anti-aliasing will reduce their effects.
Traditional high order delta-sigma modulators suffer
from potential instabilities at large input signal levels.
The proprietary architecture used for the LTC2498 third
order modulator resolves this problem and guarantees
stability with input signals 150% of full-scale. In many
industrial applications, it is not uncommon to have microvolt level signals superimposed over unwanted volt
level error sources with several volts of peak-to-peak
noise. Figures 26 and 27 show measurement results for
the rejection of a 7.5V peak-to-peak noise source (150%
INPUT NORMAL MODE REJECTION (dB)
0
fN = fEOSC/5120
–10
–20
–30
NORMAL MODE REJECTION (dB)
MEASURED DATA
CALCULATED DATA
–20
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
–60
–80
–100
–120
0
15
30
45
60
75
90 105 120 135 150 165 180 195 210 225 240
INPUT FREQUENCY (Hz)
2498 F23
Figure 23. Input Normal Mode Rejection vs Input Frequency with
Input Perturbation of 100% (60Hz Notch)
0
NORMAL MODE REJECTION (dB)
The user can expect to achieve this level of performance
using the internal oscillator, as shown in Figures 23, 24,
and 25. Measured values of normal mode rejection are
shown superimposed over the theoretical values in all
three rejection modes.
0
–40
–50
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
–60
–80
–100
–120
–60
MEASURED DATA
CALCULATED DATA
–20
0
–70
12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200
INPUT FREQUENCY (Hz)
2498 F24
–80
–90
Figure 24. Input Normal Mode Rejection vs Input Frequency with
Input Perturbation of 100% (50Hz Notch)
–100
–110
–120
0
fN
2fN 3fN 4fN 5fN 6fN 7fN
INPUT SIGNAL FREQUENCY (Hz)
8fN
2498 F21
Figure 21. Input Normal Mode Rejection at DC
NORMAL MODE REJECTION (dB)
0
INPUT NORMAL MODE REJECTION (dB)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–20
–40
–80
–100
0
20
–110
–120
250fN 252fN 254fN 256fN 258fN 260fN 262fN
INPUT SIGNAL FREQUENCY (Hz)
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
–60
–120
–100
MEASURED DATA
CALCULATED DATA
40
60
80
100
120
140
INPUT FREQUENCY (Hz)
160
180
200
220
2498 F25
2498 F22
Figure 22. Input Normal Mode Rejection at fS = 256 • fN
Figure 25. Input Normal Mode Rejection vs Input Frequency with
Input Perturbation of 100% (50Hz/60Hz Notch)
2498fg
32
For more information www.linear.com/LTC2498
LTC2498
Applications Information
Using the 2x speed mode of the LTC2498 alters the rejection characteristics around DC and multiples of fS. The
device bypasses the offset calibration in order to increase
the output rate. The resulting rejection plots are shown
in Figures 28 and 29. 1x type frequency rejection can be
achieved using the 2x mode by performing a running
average of the conversion results, see Figure 30.
Output Data Rate
When using its internal oscillator, the LTC2498 produces up
to 7.5 samples per second (sps) with a notch frequency of
60Hz. The actual output data rate depends upon the length
VIN(P-P) = 5V
VIN(P-P) = 7.5V
(150% OF FULL SCALE)
–20
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
–40
–60
–80
–100
–120
0
15
30
45
60
75
–20
–40
–60
–80
–120
90 105 120 135 150 165 180 195 210 225 240
INPUT FREQUENCY (Hz)
2498 F26
0
fN
2fN 3fN 4fN 5fN 6fN 7fN
INPUT SIGNAL FREQUENCY (fN)
8fN
2498 F28
Figure 28. Input Normal Mode Rejection 2x Speed Mode
0
0
NORMAL MODE REJECTION (dB)
0
–100
Figure 26. Measure Input Normal Mode Rejection vs Input
Frequency with Input Perturbation of 150% (60Hz Notch)
VIN(P-P) = 5V
VIN(P-P) = 7.5V
(150% OF FULL SCALE)
–20
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
–40
–60
–80
–100
–120
An increase in fEOSC over the nominal 307.2kHz will translate
into a proportional increase in the maximum output data
rate (up to a maximum of 100sps). The increase in output
rate leads to degradation in offset, full-scale error, and effective resolution as well as a shift in frequency rejection.
When using the integrated temperature sensor, the internal
oscillator should be used (fO = 0) or an external oscillator
applied to fO, fEOSC, should be set to 307.2kHz Max.
0
12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200
INPUT FREQUENCY (Hz)
2498 F27
Figure 27. Measure Input Normal Mode Rejection vs Input
Frequency With input Perturbation of 150% (50Hz Notch)
INPUT NORMAL REJECTION (dB)
NORMAL MODE REJECTION (dB)
0
of the sleep and data output cycles which are controlled
by the user and can be made insignificantly short. When
operating with an external conversion clock (fO connected
to an external oscillator), the LTC2498 output data rate
can be increased. The duration of the conversion cycle is
41036/fEOSC. If fEOSC = 307.2kHz, the converter behaves
as if the internal oscillator is used.
INPUT NORMAL REJECTION (dB)
of full scale) applied to the LTC2498. From these curves,
it is shown that the rejection performance is maintained
even in extremely noisy environments.
–20
–40
–60
–80
–100
–120
248 250 252 254 256 258 260 262 264
INPUT SIGNAL FREQUENCY (fN)
2498 F29
Figure 29. Input Normal Mode Rejection 2x Speed Mode
2498fg
For more information www.linear.com/LTC2498
33
LTC2498
Applications Information
A change in fEOSC results in a proportional change in the
internal notch position. This leads to reduced differential
mode rejection of line frequencies. The common mode
rejection of line frequencies remains unchanged, thus fully
differential input signals with a high degree of symmetry
on both the IN+ and IN– pins will continue to reject line
frequency noise.
An increase in fEOSC also increases the effective dynamic
input and reference current. External RC networks will
50
–90
WITH
RUNNING
AVERAGE
–100
–110
–120
–130
–140
40
30
10
22
–1000
20
RESOLUTION (BITS)
–FS ERROR (ppm OF VREF)
–500
TA = 25°C
TA = 85°C
VIN(CM) = VREF(CM)
–3000
VCC = VREF = 5V
fO = EXT CLOCK
–3500
0
20
10
OUTPUT DATA RATE (READINGS/SEC)
0
10
20
OUTPUT DATA RATE (READINGS/SEC)
2498 F33
Figure 33.–FS Error vs Output Data Rate
and Temperature
0
30
20
10
OUTPUT DATA RATE (READINGS/SEC)
30
2498 F32
Figure 32. +FS Error vs Output Data
Rate and Temperature
20
18
TA = 25°C
TA = 85°C
VIN(CM) = VREF(CM)
VCC = VREF = 5V
VIN = 0V
fO = EXT CLOCK
RES = LOG 2 (VREF/NOISERMS)
16
14
10
0
22
12
30
1000
Figure 31. Offset Error vs Output Data
Rate and Temperature
24
–2500
1500
2498 F31
0
–2000
2000
500
2498 F30
–1500
2500
0
Figure 30. Input Normal Mode Rejection
2x Speed Mode with and Without Running
Averaging
VIN(CM) = VREF(CM)
VCC = VREF = 5V
fO = EXT CLOCK
TA = 25°C
TA = 85°C
3000
20
–10
60
62
54 56
58
48 50
52
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
3500
VIN(CM) = VREF(CM)
VCC = VREF = 5V
VIN = 0V
fO = EXT CLOCK
TA = 25°C
TA = 85°C
+FS ERROR (ppm OF VREF)
NO AVERAGE
Once the external oscillator frequency is increased above
1MHz (a more than 3x increase in output rate) the effectiveness of internal auto calibration circuits begins to degrade.
This results in larger offset errors, full scale errors, and
decreased resolution, see Figures 31 to 38.
RESOLUTION (BITS)
–80
OFFSET ERROR (ppm OF VREF)
NORMAL MODE REJECTION (dB)
–70
continue to have zero differential input current, but the
time required for complete settling (580ns for fEOSC =
307.2kHz) is reduced, proportionally.
0
20
10
OUTPUT DATA RATE (READINGS/SEC)
30
2498 F34
Figure 34. Resolution (NoiseRMS ≤ 1LSB)
vs Output Data Rate and Temperature
18
16
TA = 25°C
TA = 85°C
VIN(CM) = VREF(CM)
12 VCC = VREF = 5V
fO = EXT CLOCK
RES = LOG 2 (VREF/INLMAX)
10
0
10
20
OUTPUT DATA RATE (READINGS/SEC)
14
30
2498 F35
Figure 35. Resolution (INLMAX ≤ 1LSB)
vs Output Data Rate and Temperature
2498fg
34
For more information www.linear.com/LTC2498
LTC2498
Applications Information
24
VIN(CM) = VREF(CM)
VIN = 0V
15 fO = EXT CLOCK
TA = 25°C
VCC = VREF = 5V
10
VCC = 5V, VREF = 2.5V
0
–5
0
20
10
OUTPUT DATA RATE (READINGS/SEC)
30
20
20
18
16 VCC = VREF = 5V
VCC = 5V, VREF = 2.5V
14 VIN(CM) = VREF(CM)
VIN = 0V
fO = EXT CLOCK
12 T = 25°C
A
RES = LOG 2 (VREF/NOISERMS)
10
0
20
10
OUTPUT DATA RATE (READINGS/SEC)
Figure 36. Offset Error vs Output Data
Rate and Reference Voltage
16 VCC = VREF = 5V
VCC = 5V, VREF = 2.5V
VIN(CM) = VREF(CM)
14
VIN = 0V
REF– = GND
12 fO = EXT CLOCK
TA = 25°C
RES = LOG 2 (VREF/INLMAX)
10
0
10
20
OUTPUT DATA RATE (READINGS/SEC)
30
2498 F38
Figure 37. Resolution (NoiseRMS ≤ 1LSB)
vs Output Data Rate and Reference
Voltage
VCC + 0.3V
VCC
GND
–0.3V
30
18
2498 F37
2480 F36
VREF
2
RESOLUTION (BITS)
5
–10
22
22
RESOLUTION (BITS)
OFFSET ERROR (ppm OF VREF)
20
Figure 38. Resolution (INLMAX ≤ 1LSB)
vs Output Data Rate and Reference
Voltage
VCC
VREF
2
–VREF
2
VREF
2
–VREF
2
GND
(a) Arbitrary
(b) Fully Differential
VCC
VCC
VREF
2
VREF
2
–VREF
2
GND
(c) Pseudo Differential Bipolar
IN– or COM Biased
Selected IN+ Ch
Selected IN– Ch or COM
–0.3V
GND
–0.3V
(d) Pseudo-Differential Unipolar
IN– or COM Grounded
2498 F39
Figure 39. Input Range
2498fg
For more information www.linear.com/LTC2498
35
LTC2498
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
UHF Package
38-Lead Plastic QFN (5mm × 7mm)
(Reference LTC DWG # 05-08-1701 Rev C)
0.70 ±0.05
5.50 ±0.05
5.15 ±0.05
4.10 ±0.05
3.00 REF
3.15 ±0.05
PACKAGE
OUTLINE
0.25 ±0.05
0.50 BSC
5.5 REF
6.10 ±0.05
7.50 ±0.05
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 ±0.10
0.75 ±0.05
PIN 1 NOTCH
R = 0.30 TYP OR
0.35 × 45° CHAMFER
3.00 REF
37
0.00 – 0.05
38
0.40 ±0.10
PIN 1
TOP MARK
(SEE NOTE 6)
1
2
5.15 ±0.10
5.50 REF
7.00 ±0.10
3.15 ±0.10
(UH) QFN REF C 1107
0.200 REF 0.25 ±0.05
R = 0.125
TYP
0.50 BSC
R = 0.10
TYP
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING CONFORMS TO JEDEC PACKAGE
OUTLINE M0-220 VARIATION WHKD
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
2498fg
36
For more information www.linear.com/LTC2498
LTC2498
Revision History
REV
DATE
DESCRIPTION
D
11/09
Update Tables 1 and 2
E
7/10
(Revision history begins at Rev D)
PAGE NUMBER
Revised Typical Application drawing
Added Note 18 to Digital Inputs and Digital Outputs section
F
2/12
Updated title of TA01b
Added H-Grade
G
11/14
17, 18
1
4, 5
1
2, 4
Clarified performance vs frequency, reduced External Oscillator Max frequency to 1MHz
5, 8, 34, 35
Clarified Input Voltage Range
3, 4, 15, 35
Added underrange note to Table 2. Fixed location of SIG bit changing state.
18
2498fg
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of itsinformation
circuits as described
herein will not infringe on existing patent rights.
For more
www.linear.com/LTC2498
37
LTC2498
Typical Application
External Buffers Provide High Impedance Inputs and Amplifier Offsets Are Automatically Cancelled
LTC2498
ΔΣ ADC
WITH
EASY DRIVE
INPUTS
MUXOUTN
INPUT
MUX
MUXOUTP
ANALOG 17
INPUTS
SDI
SCK
SDO
CS
2
–
1/2 LT6078
3
+
6
–
5
1
1/2 LT6078
1k
0.1µF
7
1k
0.1µF
+
2498 TA02
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LT 1236A-5
Precision Bandgap Reference, 5V
0.05% Max Initial Accuracy, 5ppm/°C Drift
LT1460
Micropower Series Reference
0.075% Max Initial Accuracy, 10ppm/°C Max Drift
LT1790
®
Micropower SOT-23 Low Dropout Reference Family
0.05% Max Initial Accuracy, 10ppm/°C Max Drift
LTC2400
24-Bit, No Latency ΔΣ ADC in SO-8
0.3ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200µA
LTC2410
24-Bit, No Latency ΔΣ ADC with Differential Inputs
0.8µVRMS Noise, 2ppm INL
LTC2411/LTC2411-1
24-Bit, No Latency ΔΣ ADCs with Differential Inputs in MSOP 1.45µVRMS Noise, 2ppm INL, Simultaneous 50Hz/60Hz
Rejection (LTC2411-1)
LTC2413
24-Bit, No Latency ΔΣ ADC with Differential Inputs
Simultaneous 50Hz/60Hz Rejection, 800nVRMS Noise
LTC2415/LTC2415-1
24-Bit, No Latency ΔΣ ADCs with 15Hz Output Rate
Pin Compatible with the LTC2410
LTC2414/LTC2418
8-/16-Channel 24-Bit, No Latency ΔΣ ADCs
0.2ppm Noise, 2ppm INL, 3ppm Total Unadjusted Errors 200µA
LTC2440
High Speed, Low Noise 24-Bit ΔΣ ADC
3.5kHz Output Rate, 200nVRMS Noise, 24.6 ENOBs
LTC2480
16-Bit ΔΣ ADC with Easy Drive Inputs, 600nVRMS Noise,
Programmable Gain, and Temperature Sensor
Pin-Compatible with LTC2482/LTC2484
LTC2481
16-Bit ΔΣ ADC with Easy Drive Inputs, 600nVRMS Noise, I2C
Interface, Programmable Gain, and Temperature Sensor
Pin-Compatible with LTC2483/LTC2485
LTC2482
16-Bit ΔΣ ADC with Easy Drive Inputs
Pin-Compatible with LTC2480/LTC2484
LTC2483
16-Bit ΔΣ ADC with Easy Drive Inputs, and I2C Interface
Pin-Compatible with LTC2481/LTC2485
LTC2484
24-Bit ΔΣ ADC with Easy Drive Inputs
Pin-Compatible with LTC2480/LTC2482
LTC2485
24-Bit ΔΣ ADC with Easy Drive Inputs, I2C Interface, and
Pin-Compatible with LTC2481/LTC2483
LTC2496
16-Bit 8-/16-Channel ΔΣ ADC with Easy Drive Input Current
Cancellation
Pin-Compatible with LTC2498/LTC2449
Temperature Sensor
2498fg
38 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC2498
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC2498
LT 1114 REV G • PRINTED IN USA
LINEAR TECHNOLOGY CORPORATION 2006
工商网监
湘ICP备2023018690号
