LTC2607/LTC2617/LTC2627
16-/14-/12-Bit Dual Rail-to-Rail
DACs with I2C Interface
Description
Features
Smallest Pin-Compatible Dual DACs:
LTC2607: 16 Bits
LTC2617: 14 Bits
LTC2627: 12 Bits
n Guaranteed Monotonic Over Temperature
n 27 Selectable Addresses
n 400kHz I2C Interface
n Wide 2.7V to 5.5V Supply Range
n Low Power Operation: 260µA per DAC at 3V
n Power Down to 1µA, Max
n High Rail-to-Rail Output Drive (±15mA, Min)
n Ultralow Crosstalk (30µV)
n Double-Buffered Data Latches
n Asynchronous DAC Update Pin
n LTC2607/LTC2617/LTC2627: Power-On Reset to
Zero Scale
n LTC2607-1/LTC2617-1/LTC2627-1: Power-On Reset
to Mid-Scale
n Tiny (3mm × 4mm) 12-Lead DFN Package
The LTC®2607/LTC2617/LTC2627 are dual 16-, 14- and
12-bit, 2.7V to 5.5V rail-to-rail voltage output DACs in a
12-lead DFN package. They have built-in high performance
output buffers and are guaranteed monotonic.
n
These parts establish new board-density benchmarks for
16- and 14-bit DACs and advance performance standards
for output drive and load regulation in single-supply,
voltage-output DACs.
The parts use a 2-wire, I2C compatible serial interface. The
LTC2607/LTC2617/LTC2627 operate in both the standard
mode (clock rate of 100kHz) and the fast mode (clock rate
of 400kHz). An asynchronous DAC update pin (LDAC) is
also included.
The LTC2607/LTC2617/LTC2627 incorporate a power-on
reset circuit. During power-up, the voltage outputs rise less
than 10mV above zero scale; and after power-up, they stay
at zero scale until a valid write and update take place. The
power-on reset circuit resets the LTC2607-1/LTC2617-1/
LTC2627-1 to mid-scale. The voltage outputs stay at midscale until a valid write and update takes place.
Applications
n
n
n
n
Mobile Communications
Process Control and Industrial Automation
Instrumentation
Automatic Test Equipment
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Protected by U.S. Patents including 5396245 and 6891433. Patent Pending.
Block Diagram
REFLO
11
GND
10
REF
9
12-/14-/16-BIT DAC
12
VOUTA
VCC
8
Differential Nonlinearity
(LTC2607)
12-/14-/16-BIT DAC
VOUTB
7
1.0
VCC = 5V
VREF = 4.096V
0.8
0.6
INPUT REGISTER
DAC REGISTER
0.4
DNL (LSB)
DAC REGISTER
INPUT REGISTER
0.2
0
–0.2
–0.4
–0.6
32-BIT SHIFT REGISTER
–0.8
–1.0
2-WIRE INTERFACE
0
16384
32768
CODE
49152
65535
2607 BD01b
CA0
1
CA1
2
LDAC
3
SCL
4
SDA
5
CA2
6
2607 BD01a
26071727fa
LTC2607/LTC2617/LTC2627
Absolute Maximum Ratings
Pin Configuration
(Note 1)
Any Pin to GND............................................. –0.3V to 6V
Any Pin to VCC.............................................. –6V to 0.3V
Maximum Junction Temperature........................... 125°C
Storage Temperature Range................... –65°C to 125°C
Lead Temperature (Soldering, 10 sec)................... 300°C
Operating Temperature Range:
LTC2607C/LTC2617C/LTC2627C
LTC2607C-1/LTC2617C-1/LTC2627C-1..... 0°C to 70°C
LTC2607I/LTC2617I/LTC2627I
LTC2607I-1/LTC2617I-1/LTC2627I-1.....–40°C to 85°C
TOP VIEW
CA0
1
12 VOUTA
CA1
2
11 REFLO
LDAC
3
SCL
4
SDA
5
8 VCC
CA2
6
7 VOUTB
13
10 GND
9 REF
DE12 PACKAGE
12-LEAD (4mm s 3mm) PLASTIC DFN
TJMAX = 125°C, θJA = 43°C/W
EXPOSED PAD (PIN 13) IS GND, MUST BE SOLDERED TO PCB
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2607CDE#PBF
LTC2607CDE#TRPBF
2607
12-Lead (4mm × 3mm) Plastic DFN
0°C to 70°C
LTC2607IDE#PBF
LTC2607IDE#TRPBF
2607
12-Lead (4mm × 3mm) Plastic DFN
–40°C to 85°C
LTC2607CDE-1#PBF
LTC2607CDE-1#TRPBF
26071
12-Lead (4mm × 3mm) Plastic DFN
0°C to 70°C
LTC2607IDE-1#PBF
LTC2607IDE-1#TRPBF
26071
12-Lead (4mm × 3mm) Plastic DFN
–40°C to 85°C
LTC2617CDE#PBF
LTC2617CDE#TRPBF
2617
12-Lead (4mm × 3mm) Plastic DFN
0°C to 70°C
LTC2617IDE#PBF
LTC2617IDE#TRPBF
2617
12-Lead (4mm × 3mm) Plastic DFN
–40°C to 85°C
LTC2617CDE-1#PBF
LTC2617CDE-1#TRPBF
26171
12-Lead (4mm × 3mm) Plastic DFN
0°C to 70°C
LTC2617IDE-1#PBF
LTC2617IDE-1#TRPBF
26171
12-Lead (4mm × 3mm) Plastic DFN
–40°C to 85°C
LTC2627CDE#PBF
LTC2627CDE#TRPBF
2627
12-Lead (4mm × 3mm) Plastic DFN
0°C to 70°C
LTC2627IDE#PBF
LTC2627IDE#TRPBF
2627
12-Lead (4mm × 3mm) Plastic DFN
–40°C to 85°C
LTC2627CDE-1#PBF
LTC2627CDE-1#TRPBF
26271
12-Lead (4mm × 3mm) Plastic DFN
0°C to 70°C
LTC2627IDE-1#PBF
LTC2627IDE-1#TRPBF
26271
12-Lead (4mm × 3mm) Plastic DFN
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
26071727fa
LTC2607/LTC2617/LTC2627
Electrical
Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. REF = 4.096V (VCC = 5V), REF = 2.048V (VCC = 2.7V), REFLO = 0V,
VOUT unloaded, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
LTC2627/LTC2627-1
LTC2617/LTC2617-1
LTC2607/LTC2607-1
MIN
MIN
MIN
TYP
MAX
TYP
MAX
TYP
MAX
UNITS
DC Performance
l
12
14
16
Bits
(Note 2)
l
12
14
16
Bits
DNL
Differential Nonlinearity (Note 2)
l
INL
Integral Nonlinearity
(Note 2)
l
±1.5
Load Regulation
VREF = VCC = 5V, Mid-Scale
IOUT = 0mA to 15mA Sourcing
IOUT = 0mA to 15mA Sinking
l
l
VREF = VCC = 2.7V, Mid-Scale
IOUT = 0mA to 7.5mA Sourcing
IOUT = 0mA to 7.5mA Sinking
Resolution
Monotonicity
±0.5
±1
±4
±1
LSB
LSB
±5
±16
±19
±64
0.02 0.125
0.03 0.125
0.1
0.1
0.5
0.5
0.35
0.42
2
2
LSB/mA
LSB/mA
l
l
0.04
0.05
0.25
0.25
0.2
0.2
1
1
0.7
0.8
4
4
LSB/mA
LSB/mA
ZSE
Zero-Scale Error
Code = 0
l
1
9
1
9
1
9
mV
VOS
Offset Error
(Note 6)
l
±1
±9
±1
±9
±1
±9
mV
VOS Temperature
Coefficient
GE
±7
Gain Error
l
Gain Temperature
Coefficient
±0.15 ±0.7
±7
±7
±0.15 ±0.7
±4
µV/°C
±0.15 ±0.7
±4
±4
%FSR
ppm/°C
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C.
REF = 4.096V (VCC = 5V), REF = 2.048V (VCC = 2.7V), REFLO = 0V, VOUT unloaded, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
PSR
Power Supply Rejection
VCC ±10%
ROUT
DC Output Impedance
VREF = VCC = 5V, Mid-Scale;
–15mA ≤ IOUT ≤ 15mA
VREF = VCC = 2.7V, Mid-Scale;
–7.5mA ≤ IOUT ≤ 7.5mA
ISC
MIN
TYP
MAX
–80
UNITS
dB
l
0.032
0.15
Ω
l
0.035
0.15
Ω
DC Crosstalk (Note 4)
Due to Full Scale Output Change (Note 5)
Due to Load Current Change
Due to Powering Down (Per Channel)
±4
±3
±30
µV
µV/mA
µV
Short-Circuit Output Current
VCC = 5.5V, VREF = 5.5V
Code: Zero Scale; Forcing Output to VCC
Code: Full Scale; Forcing Output to GND
l
l
15
15
36
37
60
60
mA
mA
VCC = 2.7V, VREF = 2.7V
Code: Zero Scale; Forcing Output to VCC
Code: Full Scale; Forcing Output to GND
l
l
7.5
7.5
22
30
50
50
mA
mA
l
0
VCC
V
Normal Mode
l
44
80
kΩ
DAC Powered Down
l
1
µA
Reference Input
Input Voltage Range
Resistance
Capacitance
IREF
Reference Current, Power Down Mode
64
30
0.001
pF
26071727fa
LTC2607/LTC2617/LTC2627
Electrical
Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. REF = 4.096V (VCC = 5V), REF = 2.048V (VCC = 2.7V), REFLO = 0V,
VOUT unloaded, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Power Supply
VCC
Positive Supply Voltage
For Specified Performance
l
ICC
Supply Current
VCC = 5V (Note 3)
VCC = 3V (Note 3)
DAC Powered Down (Note 3) VCC = 5V
DAC Powered Down (Note 3) VCC = 3V
l
l
l
l
2.7
0.66
0.52
0.4
0.10
5.5
V
1.3
1
1
1
mA
mA
µA
µA
Digital I/O (Note 11)
VIL
Low Level Input Voltage (SDA and SCL)
VIH
High Level Input Voltage (SDA and SCL)
0.3VCC
l
l
VIL(LDAC) Low Level Input Voltage (LDAC)
VCC = 4.5V to 5.5V
VCC = 2.7V to 5.5V
l
l
VIH(LDAC) High Level Input Voltage (LDAC)
VCC = 2.7V to 5.5V
VCC = 2.7V to 3.6V
l
l
0.7VCC
V
V
0.8
0.6
2.4
2.0
V
V
V
V
VIL(CAn)
Low Level Input Voltage on CAn
(n = 0, 1, 2)
See Test Circuit 1
l
VIH(CAn)
High Level Input Voltage on CAn (n = 0, 1, 2)
See Test Circuit 1
l
RINH
Resistance from CAn (n = 0, 1, 2)
to VCC to Set CAn = VCC
See Test Circuit 2
l
10
kΩ
RINL
Resistance from CAn (n = 0, 1, 2)
to GND to Set CAn = GND
See Test Circuit 2
l
10
kΩ
RINF
Resistance from CAn (n = 0, 1, 2)
to VCC or GND to Set CAn = Float
See Test Circuit 2
l
2
VOL
Low Level Output Voltage
Sink Current = 3mA
l
0
tOF
Output Fall Time
VO = VIH(MIN) to VO = VIL(MAX),
CB = 10pF to 400pF (Note 9)
l 20 + 0.1CB
tSP
Pulse Width of Spikes Suppressed by Input Filter
IIN
Input Leakage
0.1VCC ≤ VIN ≤ 0.9VCC
l
Note 12
l
l
0.15VCC
0.85VCC
0
V
V
MΩ
0.4
V
250
ns
50
ns
1
µA
CIN
I/O Pin Capacitance
10
pF
CB
Capacitive Load for Each Bus Line
l
400
pF
CCAX
External Capacitive Load on Address
Pins CAn (n = 0, 1, 2)
l
10
pF
26071727fa
LTC2607/LTC2617/LTC2627
Electrical
Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. REF = 4.096V (VCC = 5V), REF = 2.048V (VCC = 2.7V), REFLO = 0V,
VOUT unloaded, unless otherwise noted.
SYMBOL PARAMETER
LTC2627/LTC2627-1
LTC2617/LTC2617-1
LTC2607/LTC2607-1
MIN
MIN
MIN
CONDITIONS
TYP
MAX
TYP
MAX
TYP
MAX
UNITS
AC Performance
tS
Settling Time (Note 7)
±0.024% (±1LSB at 12 Bits)
±0.006% (±1LSB at 14 Bits)
±0.0015% (±1LSB at 16 Bits)
7
7
9
7
9
10
µs
µs
µs
Settling Time for 1LSB Step
(Note 8)
±0.024% (±1LSB at 12 Bits)
±0.006% (±1LSB at 14 Bits)
±0.0015% (±1LSB at 16 Bits)
2.7
2.7
4.8
2.7
4.8
5.2
µs
µs
µs
V/µs
Voltage Output Slew Rate
0.8
0.8
0.8
1000
1000
1000
At Mid-Scale Transition
12
12
12
180
180
180
kHz
Output Voltage Noise Density
At f = 1kHz
At f = 10kHz
120
100
120
100
120
100
nV/√Hz
nV/√Hz
Output Voltage Noise
0.1Hz to 10Hz
15
15
15
µVP-P
Capacitive Load Driving
Glitch Impulse
Multiplying Bandwidth
en
pF
nV • s
Timing
Characteristics
The l denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (See Figure 1) (Notes 10, 11)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
400
kHz
VCC = 2.7V to 5.5V
fSCL
SCL Clock Frequency
l
0
tHD(STA)
Hold Time (Repeated) Start Condition
l
0.6
µs
tLOW
Low Period of the SCL Clock Pin
l
1.3
µs
tHIGH
High Period of the SCL Clock Pin
l
0.6
µs
tSU(STA)
Set-Up Time for a Repeated Start Condition
l
0.6
tHD(DAT)
Data Hold Time
l
0
tSU(DAT)
Data Set-Up Time
l
100
tr
Rise Time of Both SDA and SCL Signals
(Note 9)
tf
Fall Time of Both SDA and SCL Signals
(Note 9)
tSU(STO)
Set-Up Time for Stop Condition
l
tBUF
Bus Free Time Between a Stop and Start Condition
l
1.3
µs
t1
Falling Edge of 9th Clock of the 3rd Input Byte to
LDAC High or Low Transition
l
400
ns
t2
LDAC Low Pulse Width
l
20
ns
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Linearity and monotonicity are defined from code kL to code
2N – 1, where N is the resolution and kL is given by kL = 0.016(2N /VREF ),
rounded to the nearest whole code. For VREF = 4.096V and N = 16, kL =
256 and linearity is defined from code 256 to code 65,535.
Note 3: SDA, SCL and LDAC at 0V or VCC, CA0, CA1 and CA2 Floating.
Note 4: DC crosstalk is measured with VCC = 5V and VREF = 4.096V, with
the measured DAC at mid-scale, unless otherwise noted.
µs
0.9
µs
l 20 + 0.1CB
300
ns
l 20 + 0.1CB
300
ns
0.6
ns
µs
Note 5: RL = 2kΩ to GND or VCC.
Note 6: Inferred from measurement at code kL (Note 2) and at full scale.
Note 7: VCC = 5V, VREF = 4.096V. DAC is stepped 1/4 scale to 3/4 scale
and 3/4 scale to 1/4 scale. Load is 2k in parallel with 200pF to GND.
Note 8: VCC = 5V, VREF = 4.096V. DAC is stepped ±1LSB between half
scale and half scale – 1. Load is 2k in parallel with 200pF to GND.
Note 9: CB = capacitance of one bus line in pF.
Note 10: All values refer to VIH(MIN) and VIL(MAX) levels.
Note 11: These specifications apply to LTC2607/LTC2607-1,
LTC2617/LTC2617-1, LTC2627/LTC2627-1.
Note 12: Guaranteed by design and not production tested.
26071727fa
LTC2607/LTC2617/LTC2627
Typical Performance Characteristics
LTC2607
Integral Nonlinearity (INL)
32
Differential Nonlinearity (DNL)
1.0
VCC = 5V
VREF = 4.096V
24
16
0.4
–8
0.2
INL (LSB)
DNL (LSB)
0
0
–0.2
–0.4
–16
16384
32768
CODE
49152
–1.0
65535
0
16384
32768
CODE
49152
2607 G01
–10 10
30
50
TEMPERATURE (°C)
70
90
DNL vs VREF
1.5
VCC = 5.5V
24
0.6
VCC = 5.5V
1.0
16
0.4
DNL (POS)
0.2
INL (LSB)
DNL (LSB)
–30
2607 G03
INL vs VREF
32
VCC = 5V
VREF = 4.096V
0
–0.2
DNL (NEG)
–0.4
0.5
INL (POS)
8
0
–8
INL (NEG)
DNL (POS)
0
DNL (NEG)
–0.5
–16
–0.6
–1.0
–24
–0.8
–1.0
–50
INL (NEG)
–32
–50
65535
DNL (LSB)
0.8
–8
2607 G02
DNL vs Temperature
1.0
0
–24
–0.8
0
INL (POS)
8
–16
–0.6
–24
VCC = 5V
VREF = 4.096V
24
0.6
8
INL (LSB)
VCC = 5V
VREF = 4.096V
0.8
16
–32
INL vs Temperature
32
–30
–10 10
30
50
TEMPERATURE (°C)
70
–32
90
0
2607 G04
1
2
3
VREF (V)
4
2µs/DIV
VCC = 5V, VREF = 4.096V
1/4-SCALE TO 3/4-SCALE STEP
RL = 2k, CL = 200pF
AVERAGE OF 2048 EVENTS
0
1
2
3
VREF (V)
4
5
2607 G06
Settling of Full-Scale Step
VOUT
100µV/DIV
SCL
2V/DIV
–1.5
2607 G05
Settling to ±1LSB
9TH CLOCK
OF 3RD DATA
BYTE
5
VOUT
100µV/DIV
9.7µs
SCL
2V/DIV
2607 G07
12.3µs
9TH CLOCK OF
3RD DATA BYTE
5µs/DIV
2607 G08
SETTLING TO ±1LSB
VCC = 5V, VREF = 4.096V
CODE 512 TO 65535 STEP
AVERAGE OF 2048 EVENTS
26071727fa
LTC2607/LTC2617/LTC2627
Typical Performance Characteristics
LTC2617
Integral Nonlinearity (INL)
8
Differential Nonlinearity (DNL)
1.0
VCC = 5V
VREF = 4.096V
6
0.6
DNL (LSB)
INL (LSB)
0.4
2
0
–2
0
SCL
2V/DIV
–0.2
–0.6
–6
0
4096
8192
CODE
12288
–1.0
16383
0
4096
8192
CODE
12288
2607 G09
2607 G11
VCC = 5V, VREF = 4.096V
1/4-SCALE TO 3/4-SCALE STEP
RL = 2k, CL = 200pF
AVERAGE OF 2048 EVENTS
16383
Differential Nonlinearity (DNL)
1.0
VCC = 5V
VREF = 4.096V
1.5
8.9µs
2607 G10
Integral Nonlinearity (INL)
2.0
9TH CLOCK
OF 3RD DATA
BYTE
2µs/DIV
–0.8
LTC2627
Settling to ±1LSB
VCC = 5V
VREF = 4.096V
0.8
0.6
1.0
0.4
0.5
DNL (LSB)
INL (LSB)
VOUT
100µV/DIV
0.2
–0.4
–4
0
–0.5
0.2
0
SCL
2V/DIV
–0.2
–0.6
–1.5
1024
2048
CODE
3072
4095
2607 G12
–1.0
9TH CLOCK
OF 3RD DATA
BYTE
2µs/DIV
–0.8
0
6.8µs
VOUT
1mV/DIV
–0.4
–1.0
–2.0
VCC = 5V
VREF = 4.096V
0.8
4
–8
Settling to ±1LSB
0
1024
2048
CODE
3072
4095
2607 G14
VCC = 5V, VREF = 4.096V
1/4-SCALE TO 3/4-SCALE STEP
RL = 2k, CL = 200pF
AVERAGE OF 2048 EVENTS
2607 G13
26071727fa
LTC2607/LTC2617/LTC2627
Typical Performance Characteristics
LTC2607/LTC2617/LTC2627
Current Limiting
CODE = MID-SCALE
0.06
0.2
∆VOUT (mV)
0
VREF = VCC = 3V
–0.04
0
–0.2
VREF = VCC = 3V
–0.6
–0.08
20
30
–1.0
–35
40
–15
–5
5
IOUT (mA)
15
25
GAIN ERROR (%FSR)
2.0
1.5
1.0
0.5
90
2
0.2
0.1
0
–0.1
–0.2
1
0
–1
–2
–0.4
–50
–30
–10 10
30
50
TEMPERATURE (°C)
70
–3
2.5
90
3
3.5
2607 G19
4
VCC (V)
4.5
5
5.5
2607 G20
ICC Shutdown vs VCC
450
0.3
400
0.2
350
0.1
300
ICC (nA)
GAIN ERROR (%FSR)
90
Offset Error vs VCC
Gain Error vs VCC
0
–0.1
250
200
150
–0.2
100
–0.3
–0.4
2.5
70
3
2607 G18
0.4
–10 10
30
50
TEMPERATURE (°C)
2607 G17
–0.3
70
–30
2607 G16
0.3
2.5
–10 10
30
50
TEMPERATURE (°C)
–1
–3
–50
35
0.4
–30
0
Gain Error vs Temperature
3
0
–50
–25
2607 G15
Zero-Scale Error vs Temperature
1
–2
–0.8
–0.10
10
–40 –30 –20 –10 0
IOUT (mA)
ZERO-SCALE ERROR (mV)
VREF = VCC = 5V
–0.4
VREF = VCC = 5V
–0.06
2
0.4
0.02
–0.02
CODE = MID-SCALE
0.6
VREF = VCC = 3V
0.04
∆VOUT (V)
0.8
VREF = VCC = 5V
Offset Error vs Temperature
3
OFFSET ERROR (mV)
0.08
Load Regulation
1.0
OFFSET ERROR (mV)
0.10
50
3
3.5
4
VCC (V)
4.5
5
5.5
2607 G21
0
2.5
3
3.5
4
VCC (V)
4.5
5
5.5
2607 G22
26071727fa
LTC2607/LTC2617/LTC2627
Typical Performance Characteristics
LTC2607/LTC2617/LTC2627
Large-Signal Response
Mid-Scale Glitch Impulse
Power-On Reset to Zeroscale
TRANSITION FROM
MS-1 TO MS
VOUT
10mV/DIV
VOUT
0.5V/DIV
9TH CLOCK
OF 3RD DATA
BYTE
SCL
2V/DIV
VREF = VCC = 5V
1/4-SCALE TO 3/4-SCALE
2.5µs/DIV
TRANSITION FROM
MS TO MS-1
2.5µs/DIV
2607 G23
Headroom at Rails
vs Output Current
4mV PEAK
VOUT
10mV/DIV
2607 G24
Supply Current vs Logic Voltage
950
VREF = VCC
5V SOURCING
850
2.5
1V/DIV
2.0
5V SINKING
1.0
3V SINKING
0.5
700
0
1
2
3
4 5 6
IOUT (mA)
7
8
9
VCC
600
VOUT
550
500µs/DIV
10
1300
1100
0.5
1
1.5 2 2.5 3 3.5 4 4.5
LOGIC VOLTAGE (V)
5
0
–3
–6
–9
VOUT
10µV/DIV
–15
dB
HYSTERSIS
370mV
900
0
Output Voltage Noise,
0.1Hz to 10Hz
Multiplying Bandwidth
–12
1000
500
2607 G28
VCC = 5V
SWEEP SCL AND
SDA OV TO VCC
AND VCC TO OV
1200
2607 G27
2607 G26
Supply Current vs Logic Voltage
–18
–21
800
–24
–27
700
–30
600
500
750
650
1.5
ICC (µA)
ICC (µA)
VOUT (V)
800
3V SOURCING
3.0
0
VCC = 5V
SWEEP LDAC
OV TO VCC
900
4.0
3.5
2607 G25
250µs/DIV
Power-On Reset to Midscale
5.0
4.5
VCC
1V/DIV
–33
0
1
2
3
LOGIC VOLTAGE (V)
4
5
2607 G029
–36
VCC = 5V
VREF (DC) = 2V
VREF (AC) = 0.2VP-P
CODE = FULL SCALE
1k
10k
100k
FREQUENCY (Hz)
0
1M
1
2
3
4 5 6
SECONDS
7
8
9
10
2607 G31
2607 G30
26071727fa
LTC2607/LTC2617/LTC2627
Typical Performance Characteristics
LTC2607/LTC2617/LTC2627
50
Short-Circuit Output Current vs
VOUT (Sinking)
40
30
20
10
0
VCC = 5.5V
VREF = 5.6V
CODE = FULL SCALE
VOUT SWEPT VCC TO 0V
–10
10mA/DIV
10mA/DIV
0
VCC = 5.5V
VREF = 5.6V
CODE = 0
VOUT SWEPT 0V TO VCC
Short-Circuit Output Current vs
VOUT (Sourcing)
–20
–30
–40
0
1
2
3
1V/DIV
4
5
6
–50
0
1
2
3
1V/DIV
2607 G32
4
5
6
2607 G33
Pin Functions
CA0 (Pin 1): Chip Address Bit 0. Tie this pin to VCC, GND
or leave it floating to select an I2C slave address for the
part (Table 1).
CA2 (Pin 6): Chip Address Bit 2. Tie this pin to VCC, GND
or leave it floating to select an I2C slave address for the
part (Table 1).
CA1 (Pin 2): Chip Address Bit 1. Tie this pin to VCC, GND
or leave it floating to select an I2C slave address for the
part (Table 1).
VOUTB (Pin 7): DAC Analog Voltage Output. The output
range is VREFLO to VREF.
LDAC (Pin 3): Asynchronous DAC Update. A falling edge
of this input after four bytes have been written into the part
immediately updates the DAC register with the contents of
the input register. A low on this input without a complete
32-bit (four bytes including the slave address) data write
transfer to the part wakes up sleeping DACs without updating the DAC output. Software power-down is disabled
when LDAC is low. LDAC is disabled when tied high.
REF (Pin 9): Reference Voltage Input. The input range
is VREFLO ≤ VREF ≤ VCC.
SCL (Pin 4): Serial Clock Input Pin. Data is shifted into
the SDA pin at the rising edges of the clock. This high
impedance pin requires a pull-up resistor or current
source to VCC.
VOUTA (Pin 12): DAC Analog Voltage Output. The output
range is VREFLO to VREF.
SDA (Pin 5): Serial Data Bidirectional Pin. Data is shifted
into the SDA pin and acknowledged by the SDA pin. This
pin is high impedance while data is shifted in and an opendrain N-channel output during acknowledgment. Requires
a pull-up resistor or current source to VCC.
VCC (Pin 8): Supply Voltage Input. 2.7V ≤ VCC ≤ 5.5V.
GND (Pin 10): Analog Ground.
REFLO (Pin 11): Reference Low. The voltage at this pin
sets the zero scale (ZS) voltage of all DACs. The VREFLO pin
can be used at voltages up to 1V for VCC = 5V, or 100mV
for VCC = 3V.
Exposed Pad (Pin 13): Ground. Must be soldered to
PCB ground.
26071727fa
10
LTC2607/LTC2617/LTC2627
Block Diagram
REFLO
11
GND
10
REF
9
VCC
12-/14-/16-BIT DAC
12
VOUTA
8
12-/14-/16-BIT DAC
DAC REGISTER
DAC REGISTER
INPUT REGISTER
INPUT REGISTER
VOUTB
7
32-BIT SHIFT REGISTER
2-WIRE INTERFACE
CA0
1
CA1
2
LDAC
3
SCL
4
SDA
CA2
5
6
2607 BD
Test Circuits
Test Circuit 1
Test Circuit 2
VDD
100Ω
CAn
RINH/RINL/RINF
CAn
VIH(CAn)/VIL(CAn)
GND
2607 TC
26071727fa
11
12
2
1
SCL
3
SA4
4
SA3
5
SA2
SLAVE ADDRESS
6
SA1
7
SA0
8
S
tHD(STA)
tLOW
tr
tHD(DAT)
tHIGH
tSU(DAT)
tf
tSU(STA)
9
1
C3
2
C2
3
C1
4
C0
5
A3
1ST DATA BYTE
6
A2
LDAC
SCL
7
A1
8
A0
2
S
Figure 2b
t1
Figure 2a
1
9TH CLOCK
OF 3RD
DATA BYTE
9
ACK
Figure 1
ALL VOLTAGE LEVELS REFER TO VIH(MIN) AND VIL(MAX) LEVELS
ACK
tf
3
4
2607 F02b
5
2ND DATA BYTE
tHD(STA)
6
7
8
tSU(STO)
tSP
9
ACK
tr
P
1
tBUF
2
S
3
4
5
3RD DATA BYTE
2607 F01
6
7
8
9
ACK
t1
t2
2607 F02A
Timing Diagrams
LDAC
SA5
SA6
SDA
START
SCL
SDA
LTC2607/LTC2617/LTC2627
26071727fa
LTC2607/LTC2617/LTC2627
Operation
Power-On Reset
The LTC2607/LTC2617/LTC2627 clear the outputs to
zero scale when power is first applied, making system
initialization consistent and repeatable. The LTC2607-1/
LTC2617‑1/LTC2627-1 set the voltage outputs to midscale
when power is first applied.
For some applications, downstream circuits are active
during DAC power-up, and may be sensitive to nonzero
outputs from the DAC during this time. The LTC2607/
LTC2617/LTC2627 contain circuitry to reduce the poweron glitch; furthermore, the glitch amplitude can be made
arbitrarily small by reducing the ramp rate of the power
supply. For example, if the power supply is ramped to 5V
in 1ms, the analog outputs rise less than 10mV above
ground (typ) during power-on. See Power-On Reset Glitch
in the Typical Performance Characteristics section.
Power Supply Sequencing
The voltage at REF (Pin 9) should be kept within the range
–0.3V ≤ VREF ≤ VCC + 0.3V (see Absolute Maximum Ratings). Particular care should be taken to observe these
limits during power supply turn-on and turn-off sequences,
when the voltage at VCC (Pin 8) is in transition.
Transfer Function
The digital-to-analog transfer function is:
k
VOUT(IDEAL ) = N ( VREF − VREFLO ) + VREFLO
2
where k is the decimal equivalent of the binary DAC
input code, N is the resolution and VREF is the voltage at
REF (Pin 6).
Serial Digital Interface
The LTC2607/LTC2617/LTC2627 communicate with a
host using the standard 2-wire I2C interface. The Timing
Diagrams (Figures 1 and 2) show the timing relationship
of the signals on the bus. The two bus lines, SDA and
SCL, must be high when the bus is not in use. External
pull-up resistors or current sources are required on these
lines. The value of these pull-up resistors is dependent
on the power supply and can be obtained from the I2C
specifications. For an I2C bus operating in the fast mode,
an active pull-up will be necessary if the bus capacitance is
greater than 200pF. The VCC power should not be removed
from the LTC2607/LTC2617/LTC2627 when the I2C bus
is active to avoid loading the I2C bus lines through the
internal ESD protection diodes.
The LTC2607/LTC2617/LTC2627 are receive-only (slave)
devices. The master can write to the LTC2607/LTC2617/
LTC2627. The LTC2607/LTC2617/LTC2627 do not respond
to a read from the master.
The START (S) and STOP (P) Conditions
When the bus is not in use, both SCL and SDA must be
high. A bus master signals the beginning of a communication to a slave device by transmitting a START condition. A
START condition is generated by transitioning SDA from
high to low while SCL is high.
When the master has finished communicating with the
slave, it issues a STOP condition. A STOP condition is
generated by transitioning SDA from low to high while
SCL is high. The bus is then free for communication with
another I2C device.
Acknowledge
The Acknowledge signal is used for handshaking between
the master and the slave. An Acknowledge (active LOW)
generated by the slave lets the master know that the latest byte of information was received. The Acknowledge
related clock pulse is generated by the master. The master
releases the SDA line (HIGH) during the Acknowledge clock
pulse. The slave-receiver must pull down the SDA bus line
during the Acknowledge clock pulse so that it remains a
stable LOW during the HIGH period of this clock pulse.
The LTC2607/LTC2617/LTC2627 respond to a write by a
master in this manner. The LTC2607/LTC2617/LTC2627
do not acknowledge a read (retains SDA HIGH during the
period of the Acknowledge clock pulse).
Chip Address
The state of CA0, CA1 and CA2 decides the slave address
of the part. The pins CA0, CA1 and CA2 can be each set
to any one of three states: VCC, GND or float. This results
26071727fa
13
LTC2607/LTC2617/LTC2627
Operation
in 27 selectable addresses for the part. The slave address
assignments are shown in Table 1.
Table 1. Slave Address Map
CA2
CA1
CA0
SA6 SA5 SA4 SA3 SA2 SA1 SA0
GND
GND
GND
GND
GND
FLOAT
0
0
1
0
0
0
1
GND
GND
VCC
0
0
1
0
0
1
0
GND
FLOAT
GND
0
0
1
0
0
1
1
GND
FLOAT
FLOAT
0
1
0
0
0
0
0
GND
FLOAT
VCC
0
1
0
0
0
0
1
GND
VCC
GND
0
1
0
0
0
1
0
GND
VCC
FLOAT
0
1
0
0
0
1
1
0
0
1
0
0
0
0
GND
VCC
VCC
0
1
1
0
0
0
0
FLOAT
GND
GND
0
1
1
0
0
0
1
FLOAT
GND
FLOAT
0
1
1
0
0
1
0
FLOAT
GND
VCC
0
1
1
0
0
1
1
FLOAT
FLOAT
GND
1
0
0
0
0
0
0
FLOAT
FLOAT
FLOAT
1
0
0
0
0
0
1
FLOAT
FLOAT
VCC
1
0
0
0
0
1
0
FLOAT
VCC
GND
1
0
0
0
0
1
1
FLOAT
VCC
FLOAT
1
0
1
0
0
0
0
FLOAT
VCC
VCC
1
0
1
0
0
0
1
VCC
GND
GND
1
0
1
0
0
1
0
VCC
GND
FLOAT
1
0
1
0
0
1
1
VCC
GND
VCC
1
1
0
0
0
0
0
VCC
FLOAT
GND
1
1
0
0
0
0
1
VCC
FLOAT
FLOAT
1
1
0
0
0
1
0
VCC
FLOAT
VCC
1
1
0
0
0
1
1
VCC
VCC
GND
1
1
1
0
0
0
0
VCC
VCC
FLOAT
1
1
1
0
0
0
1
VCC
VCC
VCC
1
1
1
0
0
1
0
1
1
1
0
0
1
1
GLOBAL ADDRESS
In addition to the address selected by the address pins,
the parts also respond to a global address. This address
allows a common write to all LTC2607, LTC2617 and
LTC2627 parts to be accomplished with one 3-byte write
transaction on the I2C bus. The global address is a 7-bit
on-chip hardwired address and is not selectable by CA0,
CA1 and CA2.
The addresses corresponding to the states of CA0, CA1
and CA2 and the global address are shown in Table 1. The
maximum capacitive load allowed on the address pins
(CA0, CA1 and CA2) is 10pF, as these pins are driven during
address detection to determine if they are floating.
Write Word Protocol
The master initiates communication with the LTC2607/
LTC2617/LTC2627 with a START condition and a 7-bit slave
address followed by the Write bit (W) = 0. The LTC2607/
LTC2617/LTC2627 acknowledges by pulling the SDA pin
low at the 9th clock if the 7-bit slave address matches the
address of the parts (set by CA0, CA1 and CA2) or the
global address. The master then transmits three bytes of
data. The LTC2607/LTC2617/LTC2627 acknowledges each
byte of data by pulling the SDA line low at the 9th clock of
each data byte transmission. After receiving three complete
bytes of data, the LTC2607/LTC2617/LTC2627 executes the
command specified in the 24-bit input word.
If more than three data bytes are transmitted after a valid
7-bit slave address, the LTC2607/LTC2617/LTC2627 do not
acknowledge the extra bytes of data (SDA is high during
the 9th clock).
The format of the three data bytes is shown in Figure 3.
The first byte of the input word consists of the 4-bit command word C3-C0, and 4-bit DAC address A3-A0. The next
two bytes consist of the 16-bit data word. The 16-bit data
word consists of the 16-, 14- or 12-bit input code, MSB
to LSB, followed by 0, 2 or 4 don’t care bits (LTC2607,
LTC2617 and LTC2627 respectively). A typical LTC2607
write transaction is shown in Figure 4.
The command (C3-C0) and address (A3-A0) assignments
are shown in Table 2. The first four commands in the table
consist of write and update operations. A write operation
loads a 16-bit data word from the 32-bit shift register
into the input register of the selected DAC, n. An update
operation copies the data word from the input register to
the DAC register. Once copied into the DAC register, the
data word becomes the active 16-, 14- or 12-bit input
code, and is converted to an analog voltage at the DAC
output. The update operation also powers up the selected
DAC if it had been in power-down mode. The data path
and registers are shown in the Block Diagram.
26071727fa
14
LTC2607/LTC2617/LTC2627
Operation
Write Word Protocol for LTC2607/LTC2617/LTC1627
S
SLAVE ADDRESS
W
A
1ST DATA BYTE
A
2ND DATA BYTE
C2
C1 C0
A3
A2
3RD DATA BYTE
A
P
INPUT WORD
Input Word (LTC2607)
C3
A
A1
A0 D15 D14 D13 D12 D11 D10 D9
1ST DATA BYTE
2ND DATA BYTE
D8 D7 D6 D5
D4
D3
D2
D1 D0
3RD DATA BYTE
Input Word (LTC2617)
C3
C2
C1 C0
A3
A2
A1
A0 D13 D12 D11 D10 D9
1ST DATA BYTE
D8
D7
2ND DATA BYTE
D6 D5 D4 D3
D2
D1
D0
X
X
X
X
3RD DATA BYTE
Input Word (LTC2627)
C3
C2
C1 C0
A3
A2
A1
A0 D11 D10 D9
1ST DATA BYTE
D8
D7
D6
2ND DATA BYTE
D5
D4 D3 D2 D1
D0
X
X
3RD DATA BYTE
2607 F03
Figure 3
Table 2
COMMAND*
C3
C2
C1
C0
0
0
0
0
Write to Input Register
0
0
0
1
Update (Power Up) DAC Register
0
0
1
1
Write to and Update (Power Up)
0
1
0
0
Power Down
1
1
1
1
No Operation
ADDRESS*
A3
A2
A1
A0
0
0
0
0
DAC A
0
0
0
1
DAC B
1
1
1
1
All DACs
*Command and address codes not shown are reserved and should not be used.
Power-Down Mode
For power-constrained applications, the power-down mode
can be used to reduce the supply current whenever one or
both of the DAC outputs are not needed. When in powerdown, the buffer amplifiers, bias circuits and reference input
are disabled and draw essentially zero current. The DAC
outputs are put into a high impedance state, and the output
pins are passively pulled to VREFLO through 90k resistors.
Input-register and DAC-register contents are not disturbed
during power-down.
Either or both DAC channels can be put into power-down
mode by using command 0100b in combination with the
appropriate DAC address. The 16-bit data word is ignored.
The supply and reference currents are reduced by approximately 50% for each DAC powered down; the effective
resistance at REF (Pin 9) rises accordingly, becoming a
high-impedance input (typically > 1GΩ) when both DACs
are powered down.
Normal operation can be resumed by executing any
command which includes a DAC update, as shown in
Table 2 or performing an asychronous update (LDAC) as
described in the next section. The selected DAC is powered
up as its voltage output is updated. When a DAC in powereddown state is powered up and updated, normal settling
is delayed. If one of the two DACs is in a powered- down
state prior to the update command, the power up delay is
5µs. If on the other hand, both DACs are powered down,
the main bias generation circuit has been automatically
shut down in addition to the DAC amplifiers and reference
input and so the power up delay time is
12µs (for VCC = 5V) or 30µs (for VCC = 3V)
Asynchronous DAC Update Using LDAC
In addition to the update commands shown in Table 2, the
LDAC pin asynchronously updates the DAC registers with
the contents of the input registers. Asynchronous update
is disabled when the input word is being clocked into
the part.
26071727fa
15
LTC2607/LTC2617/LTC2627
Operation
If a complete input word has been written to the part, a low
on the LDAC pin causes the DAC registers to be updated
with the contents of the input registers.
If the input word is being written to the part, a low going
pulse on the LDAC pin before the completion of three bytes
of data powers up the DACs but does not cause the outputs
to be updated. If LDAC remains low after a complete input
word has been written to the part, then LDAC is recognized,
the command specified in the 24-bit word just transferred
is executed and the DAC outputs updated.
The DACs are powered up when LDAC is taken low, independent of any activity on the I2C bus.
If LDAC is low at the falling edge of the 9th clock of the
3rd byte of data, it inhibits any software power-down
command that was specified in the input word. LDAC is
disabled when tied high.
Voltage Output
Both of the two rail-to-rail amplifiers have guaranteed
load regulation when sourcing or sinking up to 15mA at
5V (7.5mA at 3V).
Load regulation is a measure of the amplifiers’ ability to
maintain the rated voltage accuracy over a wide range
of load conditions. The measured change in output voltage per milliampere of forced load current change is
expressed in LSB/mA.
DC output impedance is equivalent to load regulation, and
may be derived from it by simply calculating a change in
units from LSB/mA to Ohms. The amplifiers’ DC output
impedance is 0.035Ω when driving a load well away from
the rails.
When drawing a load current from either rail, the output
voltage headroom with respect to that rail is limited
by the 30Ω typical channel resistance of the output
devices; e.g., when sinking 1mA, the minimum output
voltage = 30Ω • 1mA = 30mV. See the graph Headroom
at Rails vs Output Current in the Typical Performance
Characteristics section.
The amplifiers are stable driving capacitive loads of up
to 1000pF.
Board Layout
The excellent load regulation performance is achieved in
part by separating the signal and power grounds as REFLO
and GND pins, respectively.
The PC Board should have separate areas for the analog
and digital sections of the circuit. This keeps the digital
signals away from the sensitive analog signals and facilitates the use of separate digital and analog ground planes
that have minimal interaction with each other.
Digital and analog ground planes should be joined at only
one point, establishing a system star ground. Ideally, the
analog ground plane should be located on the component
side of the board, and should be allowed to run under the
part to shield it from noise. Analog ground should be a
continuous and uninterrupted plane, except for necessary
lead pads and vias, with signal traces on another layer.
The GND pin functions as a return path for power supply
currents in the device and should be connected to analog
ground. Resistance from the GND pin to the analog power
supply return should be as low as possible. Resistance
here will add directly to the channel resistance of the output
device when sinking load current. When a zero scale DAC
output voltage of zero is required, the REFLO pin should
be connected to system star ground. Any shared trace
resistance between REFLO and GND pins is undesirable
since it adds to the effective DC output impedance (typically 0.035Ω) of the part.
Rail-to-Rail Output Considerations
In any rail-to-rail voltage output device, the output is limited
to voltages within the supply range.
Since the analog output of the device cannot go below
ground, it may limit for the lowest codes as shown in Figure
5b. Similarly, limiting can occur near full scale when the
REF pin is tied to VCC. If VREF = VCC and the DAC full-scale
error (FSE) is positive, the output for the highest codes
limits at VCC as shown in Figure 5c. No full-scale limiting
will occur if VREF is less than VCC – FSE.
Offset and linearity are defined and tested over the region
of the DAC transfer function where no output limiting
can occur.
26071727fa
16
X = DON’T CARE
3
4
SA3
0V
OUTPUT
VOLTAGE
SA4
SA3
5
6
SA1
SA1
7
SA0
SA0
1
C3
C3
2
C2
C2
3
C1
C1
4
C0
C0
5
A3
A3
COMMAND
6
A2
A2
7
A1
A1
8
A0
A0
9
ACK
1
D15
2
D14
3
D13
4
5
D11
MS DATA
D12
6
D10
7
D9
8
D8
9
ACK
1
D7
2
D6
3
D5
(b)
OUTPUT
VOLTAGE
0
(a)
32, 768
INPUT CODE
VREF = VCC
65, 535
INPUT CODE
(c)
4
5
D3
LS DATA
D4
VREF = VCC
Figure 4. Typical LTC2607 Input Waveform—Programming DAC Output for Full Scale
9
ACK
INPUT CODE
8
WR
6
D2
Figure 5. Effects of Rail-to-Rail Operation on a DAC Transfer Curve. (a) Overall Transfer Function (b) Effect
of Negative Offset for Codes Near Zero Scale (c) Effect of Positive Full-Scale Error for Codes Near Full Scale
SA2
SA2
SLAVE ADDRESS
SA4
NEGATIVE
OFFSET
2
1
SCL
VOUT
SA5
SA6
SA5
SDA
START
SA6
7
D1
9
ACK
2607 F05
OUTPUT
VOLTAGE
POSITIVE
FSE
8
D0
2607 F04
ZERO-SCALE
VOLTAGE
FULL-SCALE
VOLTAGE
STOP
LTC2607/LTC2617/LTC2627
Operation
26071727fa
17
LTC2607/LTC2617/LTC2627
Package Description
DE/UE Package
12-Lead Plastic DFN (4mm × 3mm)
(Reference LTC DWG # 05-08-1695 Rev D)
0.70 p0.05
3.60 p0.05
2.20 p0.05
3.30 p0.05
1.70 p 0.05
PACKAGE OUTLINE
0.25 p 0.05
0.50 BSC
2.50 REF
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
4.00 p0.10
(2 SIDES)
7
R = 0.115
TYP
0.40 p 0.10
12
R = 0.05
TYP
PIN 1
TOP MARK
(NOTE 6)
0.200 REF
3.30 p0.10
3.00 p0.10
(2 SIDES)
1.70 p 0.10
0.75 p0.05
6
0.25 p 0.05
1
PIN 1 NOTCH
R = 0.20 OR
0.35 s 45o
CHAMFER
(UE12/DE12) DFN 0806 REV D
0.50 BSC
2.50 REF
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE A VARIATION OF VERSION
(WGED) IN JEDEC PACKAGE OUTLINE M0-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
26071727fa
18
LTC2607/LTC2617/LTC2627
Revision History
REV
DATE
DESCRIPTION
A
1/10
Revised Features
PAGE NUMBER
1
Added Pin Configuration and Updated Order Information
2
Added Text to Serial Digital Interface Section
13
26071727fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LTC2607/LTC2617/LTC2627
Typical Application
Demo Circuit Schematic. Onboard 20-Bit ADC Measures Key Performance Parameters
5V
5V
VREF
1V TO 5V
3
LDAC
1
CA0
2
CA1
6
CA2
I2C BUS
8
6
VCC REF
VOUTB
LTC2607
7
100Ω
7.5k
0.1µF
2
FSSET
3
CH 1
DAC
OUTPUT B
4
100Ω
12
VOUTA
5 SCL
SDA
DAC
GND
REFLO
OUTPUT A
10, 13
1
VCC
9
SCK
8
SDO
7
CS
LTC2422
7.5k
4
CH 0
ZSSET GND
5
FO
SPI BUS
10
6
2607 TA01
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LTC1458/LTC1458L
Quad 12-Bit Rail-to-Rail Output DACs with Added Functionality
LTC1458: VCC = 4.5V to 5.5V, VOUT = 0V to 4.096V
LTC1458L: VCC = 2.7V to 5.5V, VOUT = 0V to 2.5V
LTC1654
Dual 14-Bit Rail-to-Rail VOUT DAC
Programmable Speed/Power, 3.5µs/750µA, 8µs/450µA
LTC1655/LTC1655L
Single 16-Bit VOUT DACs with Serial Interface in SO-8
VCC = 5V(3V), Low Power, Deglitched
LTC1657/LTC1657L
Parallel 5V/3V 16-Bit VOUT DACs
Low Power, Deglitched, Rail-to-Rail VOUT
LTC1660/LTC1665
Octal 10/8-Bit VOUT DACs in 16-Pin Narrow SSOP
VCC = 2.7V to 5.5V, Micropower, Rail-to-Rail Output
LTC1664
Quad 10-Bit VOUT DAC in 16-Pin Narrow SSOP
VCC = 2.7V to 5.5V, Micropower, Rail-to-Rail Output
LTC1821
Parallel 16-Bit Voltage Output DAC
Precision 16-Bit Settling in 2µs for 10V Step
LTC2600/LTC2610/
LTC2620
Octal 16-/14-/12-Bit VOUT DACs in 16-Lead SSOP
250µA per DAC, 2.5V to 5.5V Supply Range, Rail-to-Rail
Output, SPI Serial Interface
LTC2601/LTC2611/
LTC2621
Single 16-/14-/12-Bit VOUT DACs in 10-Lead DFN
300µA per DAC, 2.5V to 5.5V Supply Range, Rail-to-Rail
Output, SPI Serial Interface
LTC2602/LTC2612/
LTC2622
Dual 16-/14-/12-Bit VOUT DACs in 8-Lead MSOP
300µA per DAC, 2.5V to 5.5V Supply Range, Rail-to-Rail
Output, SPI Serial Interface
LTC2604/LTC2614/
LTC2624
Quad 16-/14-/12-Bit VOUT DACs in 16-Lead SSOP
250µA per DAC, 2.5V to 5.5V Supply Range, Rail-to-Rail
Output, SPI Serial Interface
LTC2605/LTC2615/
LTC2625
Octal 16-/14-/12-Bit VOUT DACs with I2C Interface
250µA per DAC, 2.7V to 5.5V Supply Range, Rail-to-Rail
Output, I2C Interface
LTC2606/LTC2616/
LTC2626
16-/14-/12-Bit VOUT DACs with I2C Interface
270µA per DAC, 2.7V to 5.5V Supply Range, Rail-to-Rail
Output, I2C Interface
LTC2609/LTC2619/
LTC2629
Quad 16-/14-/12-Bit VOUT DACs with I2C Interface
250µA Range per DAC, 2.7V to 5.5V Supply Range,
Rail-to-Rail Output with Separate VREF Pins for Each DAC
26071727fa
20 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
LT 0110 REV A • PRINTED IN USA
LINEAR TECHNOLOGY CORPORATION 2005