LTC6433-15
Low Frequency to 1.4GHz
50Ω Gain Block IF Amplifier
Features
Description
Low Frequency to 1.4GHz Bandwidth
nn 100kHz to 1GHz Flat Gain from a Single Demo Circuit
nn Low Frequency Cutoff Is User Defined
nn 15.9dB Power Gain
nn 52dBm OIP3 at 1MHz
nn 47dBm OIP3 at 150MHz
nn NF = 3.22dB at 150MHz
nn 1nV/√Hz Total Input Noise Density at 150MHz
nn S11 < –10dB Up to 1.2GHz
nn S22 < –10dB Up to 1.0GHz
nn > 2V
P-P Linear Output Swing
nn P1dB =19.2dBm
nn DC Power = 475mW
nn 50Ω Single-Ended Operation
nn Insensitive to V
CC Variation
nn A-Grade 100% OIP3 Tested at 150MHz
nn Input/Output Internally Matched to 50Ω
nn Single 5V Supply
nn Unconditionally Stable
The LTC®6433-15 is a gain-block amplifier with excellent
linearity at frequencies below 100kHz to beyond 1000MHz
and with low associated output noise.
nn
Applications
Single-Ended IF Amplifier
ADC Driver
nn CATV
nn Test Equipment
nn
nn
The unique combination of high linearity, low noise and
low power dissipation makes this an ideal candidate for
many signal-chain applications. The LTC6433-15 is easy
to use, requiring a minimum of external components. It is
internally input/output matched to 50Ω and it draws only
95mA from a single 5V supply.
The LTC6433-15 operates over a wide bandwidth. A single
demonstration circuit offers flat gain from 100kHz to 1GHz.
While this device is not capable of DC coupled operation,
users can define the low frequency cut-off by appropriate
choice of external components.
On-chip bias and temperature compensation maintain
performance over environmental changes.
The LTC6433-15 uses a high performance SiGe BiCMOS
process for excellent repeatability compared with similar
GaAs amplifiers. All A-grade LTC6433-15 devices are tested
and guaranteed for OIP3 at 150MHz. The LTC6433-15 is
housed in a 4mm × 4mm 24-lead QFN package with an
exposed pad for thermal management and low inductance.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Typical Application
Single-Ended IF Amplifier
OIP3 and Gain vs Frequency
55
5V
RSOURCE
50Ω
1µF
FDBK
LTC6433-15
NFILT
RF
CHOKE,
470µH
50
1µF
RLOAD
50Ω
643315 TA01a
20
45
15
40
10
35
DC2168A DEMO BOARD
VCC = 5V, T = 25°C
POUT = 2dBm/TONE
ZIN = ZOUT = 50Ω
30
0.1
1
10
100
FREQUENCY (MHz)
GAIN (dB)
1µF
1µF
OIP3 (dBm)
VCC = 5V
25
OIP3
GAIN
5
0
1000
643315 TA01b
643315f
For more information www.linear.com/LTC6433-15
1
LTC6433-15
Absolute Maximum Ratings
Pin Configuration
(Note 1)
Total Supply Voltage (VCC to GND)...........................5.5V
Amplifier Output Current (OUT)............................ 115mA
RF Input Power, Continuous, 50Ω (Note 2)..........15dBm
RF Input Power, 100µs Pulse, 50Ω (Note 2).........20dBm
Operating Case Temperature
Range (TCASE)...........................................–40°C to 85°C
Storage Temperature Range................... –65°C to 150°C
Junction Temperature (TJ)..................................... 150°C
FDBK
DNC
DNC
VCC
GND
IN
TOP VIEW
24 23 22 21 20 19
DNC 1
18 OUT
DNC 2
17 GND
DNC 3
16 DNC
25
GND
DNC 4
15 T_DIODE
13 DNC
DNC
DNC
9 10 11 12
DNC
8
VCC
7
DNC
14 DNC
NFILT 6
GND
DNC 5
UF PACKAGE
24-LEAD (4mm × 4mm) PLASTIC QFN
TJMAX = 150°C, θJC = 44°C/W
EXPOSED PAD (PIN 25) IS GND, MUST BE SOLDERED TO PCB
Order Information
http://www.linear.com/product/LTC6433-15#orderinfo
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC6433AIUF-15#PBF
LTC6433AIUF-15#TRPBF
43315
24-Lead (4mm × 4mm) Plastic QFN
–40°C to 85°C
LTC6433BIUF-15#PBF
LTC6433BIUF-15#TRPBF
43315
24-Lead (4mm × 4mm) Plastic QFN
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
DC
Electrical Characteristics
The
l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C, VCC = 5V, ZSOURCE = ZLOAD = 50Ω. Typical measured DC electrical
performance using Test Circuit A.
SYMBOL PARAMETER
VS
Operating Supply Range
IS,TOT
Total Supply Current
IS,OUT
ICC,OUT
Total Supply Current to OUT Pin
Current to VCC Pin
VDIODE
Temperature Diode Voltage
TC
Diode Temperature Coefficient
2
CONDITIONS
MIN
TYP
MAX
UNITS
4.75
5.0
5.25
V
75
67
95
l
106
112
mA
mA
62
55
82
l
92
95
mA
mA
12
12.5
13
l
16
17.5
mA
mA
All VCC Pins Plus OUT
Current to OUT
Either VCC Pin May Be Used
T_Diode Current = 1mA
0.85
V
1.4
mV/°C
643315f
For more information www.linear.com/LTC6433-15
LTC6433-15
AC
Electrical Characteristics A = 25°C (Note 3), VCC = 5V, ZSOURCE = ZLOAD = 50Ω, unless otherwise
T
noted. Measurements are performed using Test Circuit A, measuring from 50Ω SMA to 50Ω SMA without de-embedding (Note 4).
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Small Signal
BW
–3dB Bandwidth
De-Embedded to Package (Low Frequency is
User Defined)
2000
MHz
S11
Input Return Loss, 100kHz to 1700MHz
De-Embedded to Package
–10
dB
S21
Forward Power Gain, 100kHz to 300MHz
De-Embedded to Package
15.8
dB
S12
Reverse Isolation, 100kHz to 3000MHz
De-Embedded to Package
–19
dB
S22
Output Return Loss, 100kHz to 1000MHz
De-Embedded to Package
–10
dB
Frequency = 100kHz
S21
Power Gain
De-Embedded to Package
16.0
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
47.8
46.0
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–91.6
–88.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–65.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–70.0
dBc
P1dB
Output 1dB Compression Point
19.2
dBm
NF
Noise Figure
De-Embedded to Package
6.67
dB
Frequency = 1MHz
S21
Power Gain
De-Embedded to Package
16.0
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
52.0
49.0
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–100
–94.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–73.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–81.0
dBc
P1dB
Output 1dB Compression Point
19.1
dBm
NF
Noise Figure
De-Embedded to Package
3.93
dB
Frequency = 10MHz
S21
Power Gain
De-Embedded to Package
15.9
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 8MHz A-Grade
B-Grade
47.6
45.5
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 8MHz A-Grade
B-Grade
–91.2
–87.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–54.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–77.0
dBc
P1dB
Output 1dB Compression Point
19.3
dBm
NF
Noise Figure
3.65
dB
De-Embedded to Package
643315f
For more information www.linear.com/LTC6433-15
3
LTC6433-15
AC
Electrical Characteristics A = 25°C (Note 3), VCC = 5V, ZSOURCE = ZLOAD = 50Ω, unless otherwise
T
noted. Measurements are performed using Test Circuit A, measuring from 50Ω SMA to 50Ω SMA without de-embedding (Note 4).
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Frequency = 50MHz
S21
Power Gain
De-Embedded to Package
15.9
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
48.0
46.0
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–92.0
–88.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–56.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–84.0
dBc
19.3
dBm
De-Embedded to Package
2.92
dB
P1dB
Output 1dB Compression Point
NF
Noise Figure
Frequency = 100MHz
S21
Power Gain
De-Embedded to Package
15.9
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
47.5
45.5
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–91.0
–87.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–55.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–80.0
dBc
19.2
dBm
De-Embedded to Package
3.10
dB
P1dB
Output 1dB Compression Point
NF
Noise Figure
Frequency = 150MHz
S21
Power Gain
De-Embedded to Package
l
14.5
14.25
15.9
16.5
16.75
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
43.0
47.2
45.0
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–82.0
–90.4
–86.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–54.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–78.0
dBc
P1dB
Output 1dB Compression Point
19.2
dBm
NF
Noise Figure
De-Embedded to Package
en
Noise Density
Input Referred
3.22
1
dB
nV/√Hz
Frequency = 240MHz
S21
Power Gain
De-Embedded to Package
15.9
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
43.1
42.0
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–82.2
–80.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–53.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–73.0
dBc
P1dB
Output 1dB Compression Point
19.1
dBm
NF
Noise Figure
3.44
dB
4
De-Embedded to Package
643315f
For more information www.linear.com/LTC6433-15
LTC6433-15
AC
Electrical Characteristics A = 25°C (Note 3), VCC = 5V, ZSOURCE = ZLOAD = 50Ω, unless otherwise
T
noted. Measurements are performed using Test Circuit A, measuring from 50Ω SMA to 50Ω SMA without de-embedding (Note 4).
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Frequency = 300MHz
S21
Power Gain
De-Embedded to Package
15.8
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
41.5
40.0
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–79.0
–76.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–51.9
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–72.0
dBc
19.0
dBm
De-Embedded to Package
3.61
dB
P1dB
Output 1dB Compression Point
NF
Noise Figure
Frequency = 500MHz
S21
Power Gain
De-Embedded to Package
15.5
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
38.4
37.0
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–72.8
–70.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–51.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–70.0
dBc
18.9
dBm
De-Embedded to Package
3.93
dB
P1dB
Output 1dB Compression Point
NF
Noise Figure
Frequency = 800MHz
S21
Power Gain
De-Embedded to Package
15.0
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
34.9
33.5
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–65.8
–63.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–47.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–59.5
dBc
18.0
dBm
De-Embedded to Package
4.40
dB
P1dB
Output 1dB Compression Point
NF
Noise Figure
Frequency = 1000MHz
S21
Power Gain
De-Embedded to Package
14.5
dB
OIP3
Output Third-Order Intercept Point
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
33.3
32.0
dBm
dBm
IM3
Third-Order Intermodulation
POUT = 2dBm/Tone, Δf = 1MHz A-Grade
B-Grade
–62.6
–60.0
dBc
dBc
HD2
Second Harmonic Distortion
POUT = 6dBm
–45.0
dBc
HD3
Third Harmonic Distortion
POUT = 6dBm
–57.0
dBc
17.3
dBm
De-Embedded to Package
4.83
dB
P1dB
Output 1dB Compression Point
NF
Noise Figure
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may
cause permanent damage to the device. Exposure to any Absolute Maximum
Rating condition for extended periods may affect device reliability and lifetime.
Note 2: Guaranteed by design and characterization. This parameter is not tested.
Note 3: The LTC6433-15 is guaranteed functional over the case operating
temperature range of –40°C to 85°C.
Note 4: Small-signal parameters S and noise are de-embedded to the package
pins, while large-signal parameters are measured directly from the circuit.
643315f
For more information www.linear.com/LTC6433-15
5
LTC6433-15
Typical
Performance Characteristics A = 25°C, VCC = 5V, ZSOURCE = ZLOAD = 50Ω, unless
T
otherwise noted. S parameter measurements are performed using 1µF feedback capacitor.
K Factor vs Frequency Over
Temperature
20
0
S11
S21
S12
S22
8
–10
–20
16
TCASE = 100°C
TCASE = 85°C
TCASE = 50°C
TCASE = 25°C
TCASE = 0°C
TCASE = –20°C
TCASE = –40°C
9
K FACTOR (UNITLESS)
MAGNITUDE (dB)
10
10
Noise Figure vs Frequency
Over Temperature
7
6
12
5
4
3
1
10
100
FREQUENCY (MHz)
0
0.1
1000 5000
1
10
100
FREQUENCY (MHz)
1000
643315 G01
643315 G03
10
8
6
10
100
FREQUENCY (MHz)
1000
0
0.1
5000
TCASE = 100°C
TCASE = 85°C
TCASE = 50°C
TCASE = 25°C
TCASE = 0°C
TCASE = –20°C
TCASE = –40°C
1
10
100
FREQUENCY (MHz)
643315 G04
–10
MAGNITUDE (dB)
MAGNITUDE (dB)
–5
–15
–20
5000
S22 vs Frequency Over Temperature
0
TCASE = 100°C
TCASE = 85°C
TCASE = 50°C
TCASE = 25°C
TCASE = 0°C
TCASE = –20°C
TCASE = –40°C
1000
643315 G05
S12 vs Frequency Over Temperature
–10
1000
12
2
–5
100
14
4
–25
0
1
10
FREQUENCY (MHz)
16
–20
1
0.1
18
–15
–30
0.1
0
.01
S21 vs Frequency Over Temperature
MAGNITUDE (dB)
MAGNITUDE (dB)
–10
5000
20
TCASE = 100°C
TCASE = 85°C
TCASE = 50°C
TCASE = 25°C
TCASE = 0°C
TCASE = –20°C
TCASE = –40°C
–5
6
643315 G02
S11 vs Frequency Over Temperature
0
8
2
1
–40
0.1
10
4
2
–30
TCASE = 100°C
TCASE = 85°C
TCASE = 25°C
TCASE = 0°C
TCASE = –20°C
TCASE = –40°C
14
NOISE FIGURE (dB)
S Parameters vs Frequency
–15
–20
TCASE = 100°C
TCASE = 85°C
TCASE = 50°C
TCASE = 25°C
TCASE = 0°C
TCASE = –20°C
TCASE = –40°C
–25
–30
–35
–40
–25
–45
–30
0.1
1
10
100
FREQUENCY (MHz)
1000
5000
–50
0.1
1
643315 G06
6
10
100
FREQUENCY (MHz)
1000
5000
643315 G07
643315f
For more information www.linear.com/LTC6433-15
LTC6433-15
Typical
Performance Characteristics
A-Grade
TA = 25°C, VCC = 5V, ZSOURCE = ZLOAD = 50Ω, unless otherwise noted. Measurements are performed using Test Circuit A, measuring
from 50Ω SMA to 50Ω SMA without de-embedding (Note 4).
OIP3 vs RF Output Power Over
OIP3 vs Frequency
OIP3 vs Voltage Over Frequency
Frequency
VCC = 5V, T = 25°C
POUT = 2dBm/TONE
fSPACE = 1MHz
ZIN = ZOUT = 50Ω
OIP3 (dBm)
45
40
55
50
50
45
45
40
40
35
30
100kHz
1MHz
10MHz
100MHz
400MHz
1GHz
25
35
20
1
10
100
FREQUENCY (MHz)
643315 G08
55
OIP3 vs Tone Spacing
Over Frequency
55
50
50
45
45
40
40
30
25
20
15
0.001
100kHz
1MHz
10MHz
100MHz
400MHz
1GHz
0.01
8
0.1
1
TONE SPACING (MHz)
10
70
100kHz
1MHz
10MHz
100MHz
400MHz
1GHz
4
4.25 4.50 4.75 5 5.25 5.50 5.75
VOLTAGE (V)
VCC = 5V, T = 25°C
POUT = 2dBm/TONE
fSPACE = 1MHz
ZIN = ZOUT = 50Ω
6
643315 G10
OIP3 vs Frequency Over
Case Temperature
35
30
25
VCC = 5V, T = 25°C
POUT = 2dBm/TONE
ZIN = ZOUT = 50Ω
15
10
643315 G09
VCC = 5V, T = 25°C
POUT = 2dBm/TONE
fSPACE = 1MHz
ZIN = ZOUT = 50Ω
35
30
20
15
–10 –8 –6 –4 –2 0 2 4 6
RF POWER OUT (dBm/TONE)
1000 5000
35
25
OIP3 (dBm)
30
0.1
OIP3 (dBm)
OIP3 (dBm)
50
55
OIP3 (dBm)
55
20
15
0.1
TCASE = 100°C
TCASE = 85°C
TCASE = 25°C
TCASE = 0°C
TCASE = –20°C
TCASE = –40°C
643315 G11
1.0
VCC = 5V
POUT = 2dBm/TONE
ZIN = ZOUT = 50Ω
10
100
FREQUENCY (MHz)
1000
643315 G12
643315f
For more information www.linear.com/LTC6433-15
7
LTC6433-15
T
Typical
Performance Characteristics A = 25°C, VCC = 5V, ZSOURCE = ZLOAD = 50Ω, unless
otherwise noted. Measurements are performed using Test Circuit A, measuring from 50Ω SMA to 50Ω SMA without de-embedding (Note 4).
–40
–40
VCC = 5V, T = 25°C
ZIN = ZOUT = 50Ω
–45
–55
–60
–65
–70
RF POUT = 6dBm
RF POUT = 8dBm
RF POUT = 10dBm
–75
–80
0.1
1
10
100
FREQUENCY (MHz)
–40
–55
–65
–70
–75
85
95
80
90
ITOTAL (mA)
10
100
FREQUENCY (MHz)
60
70
55
65
643315 G16
RF Power Out vs RF Power In
Over Frequency
VCC = 5V, T = 25°C
20 ZIN = ZOUT = 50Ω
16
14
14
13
GAIN (dB)
RF POUT (dBm)
18
6
4
2
0
–15 –12 –9 –6 –3 0 3 6
RF POWERIN (dBm)
8
9
12 15
643315 G19
10
9
85
80
75
65
–20
0
20
40
TCASE (C)
60
80
60
–15
100
VCC = 5V, T = 25°C
ZIN = ZOUT = 50Ω
–10
–5
0
5
RF POWERIN (dBm)
643315 G17
10
15
643315 G18
P1dB vs Frequency
21.0
VCC = 5V, T = 25°C
ZIN = ZOUT = 50Ω
T = 25°C
20.5 ZIN = ZOUT = 50Ω
20.0
19.5
12
11
ITOTAL vs Input Power
70
15
FREQ = 100kHz
FREQ = 1MHz
FREQ = 10MHz
FREQ = 100MHz
FREQ = 400MHz
FREQ = 1GHz
1000
90
16
10
10
100
FREQUENCY (MHz)
95
Gain vs RF Power In
Over Frequency
22
8
VCC = 5V
60
–40
6
100
80
75
12
1
643315 G15
ITOTAL vs TCASE
85
65
4.25 4.50 4.75 5 5.25 5.50 5.75
VCC (Volts)
–90
0.1
1000
P1dB (dBm)
ITOTAL (mA)
105
100
4
–75
–85
90
50
–70
–80
ITOTAL (mA)
TCASE = 25°C
70
–65
–85
110
75
–60
643315 G14
ITOTAL vs VCC
95
–55
–80
643315 G13
100
RF POUT = 6dBm
RF POUT = 8dBm
RF POUT = 10dBm
–50
–60
1
VCC = 5V, T = 25°C
ZIN = ZOUT = 50Ω
–45
RF POUT = 6dBm
RF POUT = 8dBm
RF POUT = 10dBm
–90
0.1
1000
4th Harmonic vs Frequency Over
RF Power Out
VCC = 5V, T = 25°C
ZIN = ZOUT = 50Ω
–50
–50
3RD HARMONIC (dBc)
2ND HARMONIC (dBc)
–45
3rd Harmonic vs Frequency Over
RF Power Out
4TH HARMONIC (dBc)
2nd Harmonic vs Frequency Over
RF Power Out
FREQ = 100kHz
FREQ = 1MHz
FREQ = 10MHz
FREQ = 100MHz
FREQ = 400MHz
FREQ = 1GHz
8
–15 –12 –9 –6 –3 0 3 6
RF POWERIN (dBm)
19.0
18.5
18.0
17.5
17.0
16.5
9
12 15
643315 G20
16.0
0.1
VCC = 4.5V
VCC = 5.0V
VCC = 5.5V
1
10
100
FREQUENCY (MHz)
1000
643315 G21
643315f
For more information www.linear.com/LTC6433-15
LTC6433-15
Pin Functions
GND (Pins 8, 17, 23, Exposed Pad Pin 25): Ground. For
best RF performance, all ground pins should be connected
to the printed circuit board ground plane. The exposed pad
should have multiple via holes to an underlying ground
plane for low inductance and good thermal dissipation.
IN (Pin 24): Signal Input Pin. This pin has an internally
generated 2V DC bias. A DC blocking capacitor is required.
See the Applications Information section for specific
recommendations.
VCC (Pins 9, 22): Positive Power Supply. Either VCC pin
should be connected to the 5V supply. Bypass the VCC pin
with 1000pF and 0.1µF capacitors. The 1000pF capacitor
should be physically close to the package. Pins 9 and 22
are internally connected within the package
NFILT (Pins 6): Noise Filter Capacitor. A capacitor to GND
is required to reduce low frequency noise.
FDBK (Pin 19): A feedback capacitor is required between
OUT (Pin 18) and the FDBK pin to ensure good matching
and gain flatness at low frequencies.
OUT (Pin 18): Amplifier Output Pin. A choke inductor is
necessary to provide power from the 5V supply and to
provide RF isolation. For best performance select a choke
with low DC loss and high self-resonant frequency (SRF).
A DC blocking capacitor is also required. See the Applications Information section for specific recommendations.
DNC (Pins 1 to 5, 7, 10 to 14, 16, 20, 21): Do Not Connect.
Do not connect these pins; allow them to float. Failure to
float these pins may impair operation of the LTC6433-15.
T_DIODE (Pin 15): Optional Diode. The T_DIODE can be forward-biased to ground with 1mA of current. The measured
voltage will be an indicator of chip temperature.
Block Diagram
VCC
9, 22
BIAS AND TEMPERATURE
COMPENSATION
24
FDBK
IN
OUT
15dB
GAIN
T_DIODE
NFILT
19
18
15
GND
8, 17, 23, 25 (EXPOSED PAD)
6
643315 BD
643315f
For more information www.linear.com/LTC6433-15
9
LTC6433-15
Test Circuit A
OPTIONAL
INPUT STABILITY
NETWORK
INPUT
1µF
1000pF
1µF
10µF
VSUPPLY = 5V
1µF
1µF
IN
350Ω
GND VCC DNC DNC FDBK
DNC
OUT
DNC
GND
DNC
DNC
DNC
DNC
LTC6433-15
NFILT
1µF
470µH
250Ω
240nH
280Ω
1µF
OUTPUT
T_DIODE
DNC
DNC
DNC GND VCC DNC DNC DNC
643315 F01
Figure 1. Test Circuit A Evaluation Circuit
Operation
The LTC6433-15 is a highly linear, fixed-gain amplifier
that is configured to operate single ended. Its core signal
path consists of a single amplifier stage minimizing
stability issues. The input is a Darlington pair for high
input impedance and high current gain. Additional circuit
enhancements increase the output impedance and minimize
the effects of internal Miller capacitance.
10
The LTC6433-15 starts with a classic RF gain-block topology but adds additional enhancements to achieve dramatically improved linearity. Shunt and series feedback are
added to lower the input/output impedance and match them
simultaneously to the 50Ω source and load. Meanwhile,
an internal bias controller optimizes the internal operating
point for peak linearity over environmental changes. This
circuit architecture provides low noise, excellent RF power
handling capability and wide bandwidth—characteristics
that are desirable for IF signal chain applications.
643315f
For more information www.linear.com/LTC6433-15
LTC6433-15
Applications Information
The LTC6433-15 is a highly linear fixed-gain amplifier
designed for ease of use. Implementing an RF gain stage
is often a multistep project. Typically an RF designer must
choose a bias point and design a bias network. Next the
designer needs to address impedance matching with input
and output matching networks and, finally, add stability
networks to ensure stable operation in and out of band.
These tasks are handled internally within the LTC6433-15.
Table 1 lists target frequency bands and suggested corresponding inductor values.
The LTC6433-15 has an internal self-biasing network
which compensates for temperature variation and keeps
the device biased for optimal linearity. Therefore, input
and output DC blocking capacitors are required.
Both the input and output are internally impedance
matched to 50Ω. An RF choke is required at the output
to deliver DC current to the device. The RF choke acts as
a high impedance (isolation) to the DC supply which is
at RF ground. Thus, the internal LTC6433-15 impedance
matching is unaffected by the biasing network. The open
collector output topology can deliver much more power
than an amplifier whose collector is biased through a
resistor or active load.
Choosing the Right RF Choke
Not all choke inductors are created equal. Proper selection of a choke is critical to achieve high linearity and
wide bandwidth. At frequencies below 100MHz, a large
valued choke is required. It is always important to select
an inductor with low RLOSS, as this will drop the available
voltage to the device. Also look for an inductor with high
self-resonant frequency (SRF) as this will limit the upper
frequency where the choke is useful. Above the SRF, its
parasitic capacitance dominates and the choke impedance
will drop. For these reasons, wire wound inductors are
preferred, and multilayer ceramic chip inductors should be
avoided for an RF choke. Choke inductors with magnetic
cores should be used with caution as they can contribute
distortion products themselves. We have successfully
used power inductors as chokes but their evaluation at
RF frequencies is normally left to the end user. Please see
Table 1 for suggested RF chokes. Since the LTC6433-15
is capable of such wideband operation, a single choke
value will not result in optimized performance across its
full frequency band.
Table 1. Target Frequency Bands and Suggested Inductor Values
FREQUENCY BAND
INDUCTOR
VALUE
MODEL
NUMBER
100kHz to 500kHz
470µH
LPS5030
500kHz to 1MHz
220µH
LPS5030
1MHz to 10MHz
120µH
LPS5030
10MHz to 20MHz
12µH
LPS5030
20MHz to 100MHz
1500nH
0805LS
100MHz to 500MHz
560nH
0603LS
500MHz to 1000MHz
100nH
0603LS
1000MHz to 2000MHz
51nH
0603LS
MANUFACTURER
Coilcraft
www.coilcraft.com
DC Blocking Capacitor
The role of a DC blocking capacitor is straightforward:
block the path of DC current and allow a low series impedance path for the AC signal. Lower frequencies require a
higher value of DC blocking capacitance. Generally, 1µF
will suffice for operation down to 100kHz. Care must be
taken when using high capacitance density materials.
These high capacitance materials often have high voltage
coefficients. At low frequencies this voltage dependence
creates distortion products. Film caps and NPO caps
get physically large and expensive at large capacitance
values. High quality capacitors like the X8R series offer
high capacitance density and good voltage coefficients.
They are recommended for best linearity below 1 MHz.
RF Bypass Capacitor
RF bypass capacitors act to shunt AC signals to ground
with a low impedance path. It is best to place them as
close as possible to the DC power supply pins of the
device. Any extra distance translates into additional series
inductance which lowers the self-resonant frequency and
useful bandwidth of the bypass capacitor. The suggested
bypass capacitor network consists of multiple capacitors:
a low value 1000pF capacitor to handle high frequencies
in parallel with larger 0.1µF and 1µF capacitors to handle
lower frequencies. Use ceramic capacitors of an appropriate
physical size for each capacitance value (e.g., 0402 for the
1000pF, 0805 for the 0.1µF) to minimize the equivalent
series resistance (ESR) of the capacitor.
643315f
For more information www.linear.com/LTC6433-15
11
LTC6433-15
Applications Information
Low Frequency Stability
Most RF gain blocks suffer from low frequency instability. To avoid any stability issues, the LTC6433-15 has a
feedback network that lowers the gain and matches the
input and output impedances. This feedback network
contains a series capacitor, so if at some low frequency
the feedback fails, the gain increases and gross impedance
mismatches occur—indeed a recipe for instability. Luckily,
this situation is easily resolved with a parallel capacitor
and resistor network on the input, as seen in Figure 1. This
network provides resistive loss at low frequencies and is
bypassed by the parallel capacitor within the desired band
of operation. However, if the LTC6433-15 is preceded by
a low frequency termination, such as a choke, the input
stability network is NOT required.
Test Circuit
The test circuit shown in Figure 2 is designed to allow
evaluation of the LTC6433-15 with standard single-ended
50Ω test equipment. The circuit requires a minimum of
external components. Since the LTC6433-15 is a wideband
part, the evaluation test circuit is optimized for wideband
operation. Obviously, for narrowband applications, the
circuit can be further optimized. As mentioned earlier,
input and output DC blocking capacitors are required as
this device is internally biased for optimal operation. A
frequency appropriate choke and decoupling capacitors
are required to provide DC bias to the RF out node. A 5V
supply should also be applied to either of the VCC pins on
the device. A suggested parallel 1µF, 350Ω network has
been added to the input to ensure low frequency stability. The 1µF capacitance can be increased to improve low
frequency performance. However, the designer needs to
be sure that the impedance presented at low frequency
will not create instability.
12
A 1µF noise filter capacitor is required to reduce low
frequency noise.
Please note that a number of DNC pins are connected on
the demo board. These connections are not necessary for
normal circuit operation.
Exposed Pad and Ground Plane Considerations
As with any RF device, minimizing ground inductance is
critical. Care should be taken with board layouts using
these exposed pad packages. The maximum allowable
number of minimum diameter via holes should be placed
underneath the exposed pad and connect to as many
ground plane layers as possible. This will provide good
RF ground and low thermal impedance. Maximizing the
copper ground plane will also improve heat spreading and
lower inductance. It is a good idea to cover the via holes
with a solder mask on the backside of the PCB to prevent
the solder from wicking away from the critical PCB to the
exposed pad interface.
Wideband Output Network
The DC2168A demonstration circuit has flat gain, excellent
linearity and low noise from 100kHz to 1GHz. A key to
this wide bandwidth performance is the output network.
A single RF choke is replaced with a network that gives
good RF isolation from 100kHz to 1GHz. In this case,
we use a 240nH (0603) inductor in series with a 470µH
power inductor. The 240nH inductor provides isolation at
high frequencies, while the 470µH inductor provides RF
isolation at low frequencies. Resistors are shunted across
each inductor to flatten the loss over the desired 100kHz
to 1GHz band. Our resulting output network has minimal
RLOSS which allows operation with a single 5V supply.
643315f
For more information www.linear.com/LTC6433-15
5
4
3
2
1
REVISION HISTORY
1
1ST PROTOTYPE JOHN C.
LTC6433-15
ECO
__
REV
DESCRIPTION
APPROVED
DA
08-0
Applications Information
P21
C5 VCC
1000pF
Optional Stability Network
VCC
P20
C2
1uF 0805
C1
R6
250
0603
L2
240nH
R5
280
0603
C4
0.1uF
0603
C3
1000pF
0402
C16
1uF
0805
C19
10uF
0805
C15
20
FDBK
DNC
22
24
21
VCC
DNC
GND
19
OUT
GND
C17
18
P16
R3
OPT
DNC
DNC
J2
E1
T_DIODE
12
11
7
P7
DNC
DNC
VCC
OUT
1uF 0805
17
16
U1
PPT
15
LTC6433-15
DNC
T_DIODE
5
14
DNC
IDENT
6
13
NOISE FILTER
DNC
4
VCC
P5
C18
1uF
0805
DNC
9
P4
3
DNC
10
P3
2
GND
P2
1
8
P1
IN
0805
23
1uF 0805
R1
348
25
1uF 0805
GND
J1
NC
+IN
L1
470uH
VCC
P12
P10
1
P11
C14
1000pF
2
E2
Z1
CMZ5920B
VCC
4.75V-5.25V
E3
GND
Figure 2. DC2168A Demo Board Schematic
25
55
E: UNLESS OTHERWISE SPECIFIED
DNC PINS ON U1 ARE FOR LINEAR USE ONLY
CUSTOMER NOTICE
OIP3
GAIN
50
APPROVALS
OIP3 (dBm)
SIZE
N/A
DC2168A DEMO BOARD
=SCALE
5V, T==NONE
25°C DATE:
2
POUT = 2dBm/TONE
ZIN = ZOUT = 50Ω
THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
35 VCC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
4
3
30
0.1
643315 F03
1
15
TECHNOLOGY
GAIN (dB)
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;
45 TO
HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY
PCB DES.
AK
VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL
OCTAVES OF FLAT TITLE:
GAIN
APPLICATION. COMPONENT SUBSTITUTION AND PRINTED 13 APP
ENG. JOHN C.
CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT
PERFORMANCE OR RELIABILITY. CONTACT LINEAR
TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.
40
5
20
SCHEMATIC
1630 McCarthy Blvd.
Milpitas, CA 95035
Phone: (408)432-1900 www.linear
Fax: (408)434-0507
LTC Confidential-For Customer Use
50 OHM LOW FREQUENCY
GAIN BLOCK
10
IC NO.
LTC6433-15
DEMO CIRCUIT 2168A
5
Friday, May 20, 2016
10
100
FREQUENCY (MHz)
1
0
1000
643315 F04
Figure 4. DC2168A Gain and OIP3 vs Frequency
Figure 3. LTC6433-15 DC2168A Demo Board
643315f
For more information www.linear.com/LTC6433-15
13
SHEET 1
OF
LTC6433-15
S Parameters
5V, 95mA, Z = 50Ω, T = 25°C, De-Embedded to Package Pins with 1µF Capacitors for FDBK
FREQUENCY
(MHz)
S11
(Mag)
S11
(Ph)
S21
(Mag)
S21
(Ph)
S12
(Mag)
S12
(Ph)
S22
(Mag)
S22
(Ph)
GTU
(Max)
Stability
(K)
0.10
–21.17
–154.55
16.03
–178.41
–18.94
2.35
–29.13
144.63
16.07
1.05
0.13
–21.99
–161.40
16.04
–178.87
–19.00
1.42
–29.78
144.70
16.07
1.05
0.17
–22.17
–164.29
16.04
–179.08
–18.96
1.50
–29.93
150.01
16.07
1.05
0.22
–22.53
–168.19
16.04
–179.35
–18.97
1.53
–31.07
150.94
16.07
1.05
0.28
–22.44
–170.32
16.03
–179.66
–19.00
0.55
–31.75
151.77
16.06
1.05
0.36
–22.76
–174.13
16.02
–179.71
–18.92
0.74
–31.05
156.67
16.05
1.05
0.46
–22.71
–175.92
16.01
–179.92
–18.88
0.95
–32.09
158.81
16.04
1.05
0.60
–22.83
–176.07
16.00
179.94
–18.87
0.19
–32.59
150.96
16.03
1.05
0.77
–22.90
–177.62
16.00
179.89
–18.88
0.35
–32.60
165.65
16.03
1.05
0.99
–22.85
–179.20
15.98
179.83
–18.96
0.45
–33.27
173.04
16.01
1.05
1.28
–22.81
59.69
15.99
179.84
–18.90
–0.15
–33.35
165.78
16.01
1.05
1.66
–22.98
179.51
15.98
179.62
–18.84
0.06
–33.19
163.84
16.00
1.05
2.14
–23.04
179.30
15.96
179.69
–18.90
0.10
–34.38
165.49
15.99
1.05
2.76
–23.14
59.39
15.96
179.56
–18.93
0.17
–34.22
166.41
15.98
1.05
3.53
–23.13
179.63
15.96
179.44
–18.86
0.17
–34.35
171.91
15.98
1.05
4.56
–23.23
177.95
15.95
179.46
–18.89
–0.58
–35.02
–59.59
15.97
1.05
5.91
–23.22
179.18
15.95
179.26
–18.89
0.05
–36.06
59.25
15.97
1.05
7.64
–23.39
59.83
15.94
179.16
–18.84
–0.59
–34.48
178.68
15.96
1.05
9.82
–23.30
179.10
15.93
178.95
–18.88
–0.77
–35.63
–176.60
15.95
1.05
12.6
–23.37
–59.79
15.93
178.71
–18.86
–1.01
–35.95
–174.44
15.95
1.05
16.3
–23.33
–179.27
15.92
178.34
–18.87
–1.39
–35.75
–169.41
15.94
1.05
21.1
–23.36
–59.87
15.92
177.89
–18.87
–1.77
–35.56
–166.88
15.94
1.05
27.2
–23.31
–178.86
15.91
177.37
–18.86
–2.25
–36.36
–156.65
15.93
1.05
35.0
–23.36
–178.71
15.91
176.71
–18.88
–2.96
–35.39
–150.36
15.93
1.05
44.7
–23.37
60.22
15.91
175.81
–18.89
–3.73
–34.47
–147.63
15.93
1.05
58.1
–23.14
–178.81
15.91
174.63
–18.91
–4.77
–33.34
–137.94
15.93
1.05
75.3
–23.16
60.12
15.92
173.12
–18.92
–6.20
–31.32
–132.08
15.94
1.05
97.1
–23.15
58.97
15.93
171.06
–18.93
–7.79
–29.78
–129.06
15.96
1.05
124.7
–23.06
176.54
15.94
168.50
–18.93
–10.00
–28.36
–131.68
15.97
1.05
159.8
–23.05
175.44
15.96
165.17
–18.93
–12.70
–27.35
–136.57
15.99
1.05
207.5
–23.11
174.45
15.97
160.31
–18.92
–16.52
–26.45
–138.23
16.00
1.05
268.5
–23.27
173.39
15.91
154.08
–18.95
–21.56
–26.24
–140.47
15.94
1.05
346.3
–22.28
171.00
15.76
146.33
–19.01
–28.30
–26.83
–130.53
15.79
1.06
443.5
–22.24
167.12
15.56
137.71
–19.18
–36.31
–24.05
–105.26
15.60
1.08
570.8
–23.19
160.37
15.35
126.33
–19.44
–46.52
–19.01
–99.82
15.42
1.09
740.7
–24.51
163.54
15.09
111.18
–19.83
–59.90
–14.36
–108.76
15.26
1.11
958.6
–22.68
–171.11
14.64
91.27
–20.47
–77.09
–10.35
–124.40
15.09
1.12
1232.8
–17.01
–172.86
13.82
65.84
–21.53
–98.71
–6.96
–146.60
14.88
1.09
1579.5
–12.08
158.84
12.10
37.27
–23.30
–124.44
–4.40
–175.70
14.34
1.07
2000.1
–9.02
119.72
9.99
6.13
–26.19
–151.27
–3.05
150.16
13.55
1.25
14
643315f
For more information www.linear.com/LTC6433-15
LTC6433-15
Package Description
Please refer to http://www.linear.com/product/LTC6433-15#packaging for the most recent package drawings.
UF Package
24-Lead Plastic QFN (4mm × 4mm)
(Reference LTC DWG # 05-08-1697 Rev B)
0.70 ±0.05
4.50 ±0.05
2.45 ±0.05
3.10 ±0.05 (4 SIDES)
PACKAGE OUTLINE
0.25 ±0.05
0.50 BSC
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
4.00 ±0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
R = 0.115
TYP
0.75 ±0.05
PIN 1 NOTCH
R = 0.20 TYP OR
0.35 × 45° CHAMFER
23 24
PIN 1
TOP MARK
(NOTE 6)
0.40 ±0.10
1
2
2.45 ±0.10
(4-SIDES)
(UF24) QFN 0105 REV B
0.200 REF
0.00 – 0.05
0.25 ±0.05
0.50 BSC
NOTE:
1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
643315f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more
www.linear.com/LTC6433-15
tion that the interconnection
of itsinformation
circuits as described
herein will not infringe on existing patent rights.
15
LTC6433-15
Typical Application
5V
VCC = 5V
1µF
RSOURCE
50Ω
1µF
1µF
RF
CHOKE,
470µH
FDBK
LTC6433-15
1µF
NFILT
RLOAD
50Ω
643315 TA02
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
Fixed Gain IF Amplifiers/ADC Drivers
LTC6431-15/LTC6431-20
15dB/20dB Gain 50Ω Gain Block IF Amplifier—
Single Ended
OIP3 = 47dBm at 240MHz, 20MHz to 1700MHz Bandwidth,
3.3dB/2.60dB NF
LTC6430-15/LTC6430-20
15dB/20dB Gain Block IF Amplifier—Differential
OIP3 = 50dBm at 240MHz, 20MHz to 1700MHz Bandwidth,
3.3dB/2.60dB NF
LTC6417
1.6GHz Low Noise High Linearity Differential Buffer/
ADC Driver
OIP3 = 41dBm at 300MHz; Can Drive 50Ω Differential Output;
High Speed Voltage Clamping Protects Subsequent Circuitry
LTC6416
2GHz, 16-Bit Differential ADC Buffer
–72dBc IM2 at 300MHz 2VP-P Composite, IS = 42mA,
eN = 2.8nV/√Hz; A V = 0dB; 300MHz
LTC6410-6
1.4GHz Differential IF Amplifier with Configurable Input
Impedance
OIP3 = 36dBm at 70MHz; Flexible Interface-to-Mixer IF Port
LTC6400-8/LTC6400-14
1.8GHz Low Noise, Low Distortion Differential
ADC Drivers
–71dBc IM3 at 240MHz 2VP-P Composite, IS = 90mA,
A V = 8dB/ 14dB/ 20dB/ 26dB
Variable Gain IF Amplifiers/ADC Drivers
LTC6412
800MHz, 31dB Range Analog-Controlled VGA
OIP3 = 35dBm at 240MHz; Continuously Adjustable Gain Control
Baseband Differential Amplifiers
LTC6409
1.1nV Hz Single Supply Differential/ADC Driver
88SFDR at 100MHz, AC or DC Couple Inputs
LT6411
Low Power Differential ADC Driver/Dual Selectable
Gain Amplifier
–83dBc IM3 at 70MHz 2VP-P Composite; A V = 1, –1 or 2;
16mA; Excellent for Single-Ended to Differential Conversion
LTC6406
3GHz Rail-to-Rail Input Differential Amplifier/
ADC Driver
–65dBc IM3 at 50MHz 2VP-P Composite; Rail-to-Rail Inputs;
eN = 1.6nV/√Hz; 18mA
LTC6404-1/LTC6404-2
Low Noise Rail-to-Rail Output Differential Amplifier/
ADC Driver
16-Bit SNR, SFDR at 10MHz; Rail-to-Rail Outputs;
eN = 1.5nV/√Hz; LTC6404-1 Is Unity-Gain Stable,
LTC6404-2 Is Gain-of-Two Stable
LTC2107
16-Bit, 210Msps ADCs
98.0dBFS SFDR 80dBFs Noise Floor, 2.40VP-P or 1.60VP-P Input
LTC2259-16
16-Bit, 80Msps, 1.8V ADC
72.0 dBFS Noise Floor, SFDR > 82dB at 140MHz, 2.00VP-P Input
LTC2160/LTC2161/
LTC2162/LTC2163/
LTC2164/LTC2165
16-Bit, 25Msps/40Msps/65Msps/80Msps/105Msps/
105Msps, 1.8V ADCs
76.2 dBFS Noise Floor, SFDR > 84dB at 140MHz, 2.00VP-P Input
High Speed ADCs
LTC2150-14/LTC2151-14/ 14-Bit, 170Msps/210Msps/250Msps/310Msps, 1.8V ADCs
LTC2152-14/LTC2153-14
Single ADCs, >68dB SNR, >88dB SFDR, 1.32VP-P Input Range
LTC2208/LTC2209
74.0 dBFS Noise Floor, SFDR >89dB at 140MHz, 2.25VP-P Input
16
16-Bit, 130Msps/160Msps ADCs
643315f
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC6433-15
(408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com/LTC6433-15
LT 0616 • PRINTED IN USA
LINEAR TECHNOLOGY CORPORATION 2016
工商网监
湘ICP备2023018690号
