LTC6905
17MHz to 170MHz
Resistor Set SOT-23 Oscillator
FEATURES
DESCRIPTION
n
The LTC®6905 precision, programmable silicon oscillator is easy to use and occupies very little board space. It
requires only a single resistor to set the output frequency
from 17MHz to 170MHz with a typical frequency error of
0.5% or less.
n
n
n
n
n
n
n
n
n
n
The LTC6905 features a proprietary feedback loop that
linearizes the relationship between RSET and frequency,
eliminating the need for tables to calculate frequency. The
oscillator can be easily programmed using the simple
formula outlined below:
APPLICATIONS
n
n
n
n
The LTC6905 operates with a single 2.7V to 5.5V power
supply and provides a rail-to-rail, 50% duty cycle square
wave output. The CMOS output driver ensures fast rise/fall
times and rail-to-rail switching. Operation is simple: A
single resistor, RSET, between 10k to 25k is used to set
the frequency, and an internal three-state divider (DIV
input) allows for division of the master clock by 1, 2 or 4,
providing three frequencies for each RSET value.
High Frequency Precision Oscillator
High Speed Data Bus Clock
Fixed Crystal Oscillator Replacement
Ceramic Oscillator Replacement
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
ThinSOT is a trademark of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
Protected by U.S. Patents including 6614313, 6342817.
TYPICAL APPLICATION
fOSC
⎧1, DIV Pin = V +
⎛ 168.5MHz • 10kΩ
⎞ 1
⎪
=⎜
+ 1.5MHz⎟ • , N = ⎨2, DIV Pin = Open
⎝
⎠ N
RSET
⎪4, DIV Pin = GND
⎩
For higher accuracy, fixed frequency versions that
include an internal frequency-setting resistor, see the
LTC6905-XXX Series data sheet.
Typcial Distribution of Frequency Error, TA = 25°C
60
50
Basic Connection
V+ = 3V
RSET = 12k
DIV = 1
40
17.225MHz ≤ fOSC ≤ 170MHz
5V
1
0.1μF
10k ≤ RSET ≤ 25k
2
3
V+
OUT
LTC6905
5
5V
GND
SET
UNITS
n
One External Resistor Sets the Frequency
Fast Start-Up Time: 100μs Typical
Frequency Range: 17MHz to 170MHz
Frequency Error ±0.5% Typ 17MHz to 170MHz
(TA = 0°C to 70°C, Over All Settings)
±20ppm/°C Temperature Stability
Rise Time: 0.5ns, CL = 5pF
Timing Jitter: 7.2ps RMS at 170MHz
50% ±2.5% Duty Cycle
6mA Typical Supply Current, fOSC = 100MHz
CMOS Output Drives 500Ω Load (VS = 3V)
Operates from a Single 2.7V to 5.5V Supply
Low Profile (1mm) ThinSOT ™ Package
30
20
÷1
DIV
6905 TA01
4
÷2
OPEN
10
÷4
0
–0.5
–0.3
–0.1
0.1
% ERROR
0.3
0.5
6905 TA02
NOTE: RESISTOR, RSET, TOLERANCE WILL ADD
TO THE FREQUENCY ERROR
6905fd
1
LTC6905
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Note 1)
Supply Voltage (V+) to GND .........................– 0.3V to 6V
DIV to GND .................................... – 0.3V to (V+ + 0.3V)
SET to GND .................................... – 0.3V to (V+ + 0.3V)
Output Short-Circuit Duration (Note 6) ........... Indefinite
Operating Temperature Range (Note 7)
LTC6905C, I .........................................– 40°C to 85°C
LTC6905H ..........................................– 40°C to 125°C
LTC6905MP .......................................– 55°C to 125°C
Specified Temperature Range (Note 8)
LTC6905C ................................................ 0°C to 70°C
LTC6905I..............................................– 40°C to 85°C
LTC6905H ..........................................– 40°C to 125°C
LTC6905MP .......................................– 55°C to 125°C
Storage Temperature Range...................– 65°C to 150°C
Lead Temperature (Soldering, 10 sec) .................. 300°C
TOP VIEW
V+ 1
5 OUT
GND 2
SET 3
4 DIV
S5 PACKAGE
5-LEAD PLASTIC SOT-23
TJMAX = 125°C, θJA = 160°C/W
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL (MINI)
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
LTC6905CS5#TRMPBF
LTC6905CS5#TRPBF
LTBJC
5-Lead Plastic SOT-23
LTC6905IS5#TRMPBF
LTC6905IS5#TRPBF
LTBJC
5-Lead Plastic SOT-23
LTC6905HS5#TRMPBF
LTC6905HS5#TRPBF
LTBJC
5-Lead Plastic SOT-23
LTC6905MPS5#TRMPBF
LTC6905MPS5#TRPBF
LTDVW
5-Lead Plastic SOT-23
LEAD BASED FINISH
TAPE AND REEL (MINI)
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
LTC6905MPS5#TRM
LTC6905MPS5#TR
LTDVW
5-Lead Plastic SOT-23
TRM = 500 pieces. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on lead based finish parts.
TEMPERATURE RANGE
0°C to 70°C
–40°C to 85°C
–40°C to 125°C
–55°C to 125°C
TEMPERATURE RANGE
–55°C to 125°C
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
6905fd
2
LTC6905
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full specified
temperature range, otherwise specifications are at TA = 25°C or as noted. V+ = 2.7V to 5.5V, RL = 15k, CL = 5pF, Pin 4 = V+ unless
otherwise noted. All voltages are with respect to GND.
SYMBOL
Δf
PARAMETER
Frequency Accuracy (Notes 2, 9)
CONDITIONS
MIN
V+ = 2.7V, 17.225MHz < f < 170MHz
V+ = 5V, 17.225MHz < f < 170MHz
LTC6905CS5
V+ = 2.7V, 17.225MHz < f < 170MHz
V+ = 5V, 17.225MHz < f < 170MHz
LTC6905MPS5 (25°C ≤ T ≤ 125°C),
LTC6905HS5 (25°C ≤ T ≤ 125°C),
LTC6905IS5 (25°C ≤ T ≤ 85°C)
V+ = 2.7V, 17.225MHz < f < 170MHz
V+ = 5V, 17.225MHz < f < 170MHz
LTC6905MPS5 (–55°C < T < 125°C),
LTC6905HS5 (–40°C ≤ T ≤ 125°C),
LTC6905IS5 (–40°C ≤ T ≤ 85°C)
V+ = 2.7V, 17.225MHz < f < 170MHz
V+ = 5V, 17.225MHz < f < 170MHz
Δf
Frequency Accuracy (Notes 2, 9)
RSET
Frequency-Setting Resistor Range
TYP
MAX
UNITS
±0.5
±1.4
±2.2
%
%
±1.7
±2.5
%
%
±1.9
±2.9
%
%
±3.5
±3.5
%
%
25
kΩ
l
l
l
l
10
fMAX
Maximum Frequency
Pin 4 = V+, N = 1
fMIN
Minimum Frequency
Pin 4 = 0V, N = 4
Δf/ΔT
Freq Drift Over Temp (Note 2)
RSET = 10k
l
±20
ppm/°C
Freq Drift Over Supply (Notes 2, 9)
V+ = 2.7V to 5.5V, R
l
0.5
%/V
0.8
%
Δf/ΔV
SET = 10k
Peak-to-Peak Timing Jitter (Note 3)
Long-Term Stability of Output Frequency
IS
VIH
Operating Supply Range
Power Supply Current
MHz
MHz
300
Duty Cycle
V+
170
17.225
l
47.5
l
2.7
50
ppm/√kHr
52.5
%
5.5
V
RSET = 10k, N = 1, RL = ∞,
fOSC = 170MHz, CL = 5pF
V+ = 5.5V
V+ = 2.7V
l
l
14
7
20
12
mA
mA
RSET = 20k, N = 4, RL = ∞,
fOSC = 21.44MHz, CL = 5pF
V+ = 5.5V
V+ = 2.7V
l
l
5
3
7
5
mA
mA
High Level DIV Input Voltage
l
l
V+ – 0.15
V
VIL
Low Level DIV Input Voltage
IDIV
DIV Input Current (Note 4)
Pin 4 = V+
Pin 4 = 0V
–40
15
–11
VOH
High Level Output Voltage (Note 4)
V+ = 5.5V, Pin 4 = 0V
IOH = –1mA
IOH = –4mA
l
l
5.25
5.20
5.45
5.30
V
V
V+ = 2.7V, Pin 4 = 0V
IOH = –1mA
IOH = –4mA
l
l
2.5
2.4
2.6
2.4
V
V
V+ = 5.5V
V+ = 5.5V
l
0.2
V
40
μA
μA
6905fd
3
LTC6905
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full specified
temperature range, otherwise specifications are at TA = 25°C or as noted. V+ = 2.7V to 5.5V, RL = 15k, CL = 5pF, Pin 4 = V+ unless
otherwise noted. All voltages are with respect to GND.
SYMBOL
VOL
tr , tf
PARAMETER
CONDITIONS
Low Level Output Voltage (Note 4)
V+ = 5.5V, Pin 4 = 0V
MIN
IOL = 1mA
IOL = 4mA
V+ = 2.7V, Pin 4 = 0V
IOL = 1mA
IOL = 4mA
TYP
MAX
UNITS
l
l
0.05
0.2
0.25
0.3
V
V
l
l
0.1
0.4
0.3
0.5
V
V
OUT Rise/Fall Time (Note 5)
0.5
V+ = 5.5V
V+ = 2.7V
Voltage at RSET Pin
VSET
l
l
4.27
1.61
4.5
1.7
ns
4.73
1.79
V
V
Note 6: A heat sink may be required to keep the junction temperature
below the absolute maximum when the output is shorted indefinitely.
Note 7: The LTC6905C is guaranteed functional over the operating
temperature range.
Note 8: The LTC6905C is guaranteed to meet specified performance from
0°C to 70°C. The LTC6905C-XXX is designed, characterized and expected
to meet specified performance from –40°C to 85°C but is not tested or QA
sampled at these temperatures. The LTC6905I-XXX is guaranteed to meet
specified performance from –40°C to 85°C.
Note 9: The LTC6905 is optimized for the performance with a 3V power
supply voltage. Please consult LTC Marketing for parts optimized for 5V
operation.
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Frequency accuracy is defined as the deviation from the fOSC
equation. Accuracy is tested with DIV = V+, N = 1 and other divide ratios
are guaranteed by design.
Note 3: Jitter is the ratio of the peak-to-peak distribution of the period to
the mean of the period. This specification is based on characterization and
is not 100% tested.
Note 4: To conform with the Logic IC Standard convention, current out of
a pin is arbitrarily given as a negative value.
Note 5: Output rise and fall times are measured between the 10% and
90% power supply levels.
TYPICAL PERFORMANCE CHARACTERISTICS
Supply Current vs Frequency
5.5V
2.7V
16
14
÷1
12
10
÷2
8
÷1
÷4
6
÷2
4
÷4
1.20
0.20
0
–0.20
–0.40
–0.60
2
0
Frequency Error vs Supply Voltage
1.40
0.40
FREQUENCY ERROR (%)
SUPPLY CURRENT (mA)
Frequency Error vs RSET
0.60
FREQUENCY ERROR (%)
18
50
100
FREQUENCY (MHz)
150
200
6905 G01
10
0.80
0.60
0.40
0.20
0
–0.20
–0.80
0
1.00
12
14
16
18
RSET (kΩ)
20
22
24
6905 G02
–0.40
2.5
3
3.5
4
4.5
SUPPLY VOLTAGE (V)
5
5.5
6905 G03
6905fd
4
LTC6905
TYPICAL PERFORMANCE CHARACTERISTICS
ROUT vs V+
Jitter vs Frequency
45
0.8
40
35
30
25
20
15
10
÷4
÷2
PERCENTAGE ERROR (%)
1.00
PEAK-TO-PEAK JITTER (%)
OUTPUT RESISTANCE (Ω)
Frequency vs Temperature
1.0
1.20
÷1
0.80
0.60
0.40
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
0.20
5
–0.8
0
0
2.5
3
3.5
4
4.5
SUPPLY VOLTAGE (V)
5
5.5
0
20
40
60 80 100 120 140 160 180
FREQUENCY (MHz)
–1.0
–40 –20
0
20 40 60 80 100 120
TEMPERATURE (°C)
6905 G08
6905 G05
6905 G04
LTC6905 Output Operating at
170MHz, VS = 3V
LTC6905 Output Operating at
17.5MHz, VS = 3V
1V/DIV
1V/DIV
12.5ns/DIV
6905 G06
1ns/DIV
6905 G07
PIN FUNCTIONS
V+ (Pin 1): Voltage Supply (2.7V ≤ V+ ≤ 5.5V). This supply must be kept free from noise and ripple. It should be
bypassed directly to the GND (Pin 2) with a 0.1μF capacitor or higher.
GND (Pin 2): Ground. Should be tied to a ground plane
for best performance.
SET (Pin 3): Frequency-Setting Resistor Input. The value
of the resistor connected between this pin and V+ determines the oscillator frequency. The voltage on this pin is
held by the LTC6905 to approximately 1V below the V+
voltage. For best performance, use a precision metal film
resistor with a value between 10k and 25k and limit the
capacitance on this pin to less than 10pF.
DIV (Pin 4): Divider-Setting Input. This three-state input
selects among three divider settings, determining the value
of N in the frequency equation. Pin 4 should be tied to V+
for the ÷1 setting, the highest frequency range. Floating
Pin 4 divides the master oscillator by 2. Pin 4 should
be tied to GND for the ÷4 setting, the lowest frequency
range. To detect a floating DIV pin, the LTC6905 attempts
to pull the pin toward midsupply. This is realized with two
internal current sources, one tied to V+ and Pin 4 and the
other one tied to ground and Pin 4. Therefore, driving
the DIV pin high requires sourcing approximately 15μA.
Likewise, driving DIV low requires sinking 11μA. When
Pin 4 is floated, it should be bypassed by a 1nF capacitor
to ground or it should be surrounded by a ground shield
to prevent excessive coupling from other PCB traces.
OUT (Pin 5): Oscillator Output. This pin can drive 5kΩ
and/or 5pF loads. For larger loads, refer to the Applications
Information section.
6905fd
5
LTC6905
BLOCK DIAGRAM
1
VRES = 1V ±5%
(V+ – VSET)
V+
PROGRAMMABLE
DIVIDER
(÷1, 2 OR 4)
+
RSET
GAIN = 1
IRES
3
SET
–
fOSC =
fMO
N
OUT
5
MASTER OSCILLATOR
V+
DIVIDER
SELECT
15μA
+
–
2 GND
–
VBIAS
IRES
DIV
THREE-STATE
INPUT DETECT
+
4
15μA
GND
6905 BD
6905fd
6
LTC6905
THEORY OF OPERATION
A resistor RSET , connected between the V+ and SET pins,
“locks together” the voltage (V+ – VSET) and current, IRES,
variation. This provides the LTC6905’s high precision. The
master oscillation frequency reduces to:
168.5MHz • 10k Ω
fMO =
+ 1.5MHz
RSET
To extend the output frequency range, the master oscillator
signal is divided by 1, 2 or 4 before driving OUT (Pin 5).
The LTC6905 is optimized for use with resistors between
10k and 25k, corresponding to oscillator frequencies
between 17.225MHz and 170MHz. The divide-by value is
determined by the state of the DIV input (Pin 4). Tie DIV to
V+ or drive it to within 0.4V of V+ to select ÷1. This is the
highest frequency range, with the master output frequency
passed directly to OUT. The DIV pin may be floated or driven
to midsupply to select ÷2, the intermediate frequency
range. The lowest frequency range, ÷4, is selected by
tying DIV to GND or driving it below 0.5V. Figure 1 shows
the relationship between RSET , divider setting and output
frequency, including the overlapping frequencies.
30
25
÷4 ÷2
RSET (Ω)
As shown in the Block Diagram, the LTC6905’s master
oscillator is controlled by the ratio of the voltage between
the V+ and SET pins and the current entering the SET pin
(IRES). The voltage on the SET pin is forced to approximately 1V below V+ by the PMOS transistor and its gate
bias voltage.
÷1
20
15
10
5
10
110
60
160
OUTPUT FREQUENCY (MHz)
6905 F01
Figure 1. RSET vs Output Frequency
6905fd
7
LTC6905
APPLICATIONS INFORMATION
SELECTING THE DIVIDER SETTING AND RESISTOR
The LTC6905’s master oscillator has a frequency range
spanning 68.9MHz to 170MHz. A programmable divider
extends the frequency range from 17.225MHz to 170MHz.
Table 1 describes the recommended frequencies for each
divider setting. Note that the ranges overlap; at some frequencies there are two divider/resistor combinations that
result in the same frequency. Choosing a higher divider
setting will result in less jitter at the expense of slightly
higher supply current.
Table 1. Frequency Range vs Divider Setting
DIVIDER SETTING
FREQUENCY RANGE
÷1
⇒
DIV (Pin 4) = V+
68.9MHz to 170MHz
÷2
⇒
DIV (Pin 4) = Floating
34.45MHz to 85MHz
÷4
⇒
DIV (Pin 4) = GND
17.225MHz to 43MHz
After choosing the proper divider setting, determine the
correct frequency-setting resistor. Because of the linear
correspondence between oscillation period and resistance,
a simple equation relates resistance with frequency.
⎧1
168.5MHz ⎞
⎪
RSET
, N = ⎨2
⎟
OSC • N – 1.5MHz ⎠
⎪4
⎩
(RSETMIN = 10k, RSETMAX = 25k)
⎛
= 10k • ⎜
⎝f
Any resistor, RSET , tolerance adds to the inaccuracy of
the oscillator. fOSC.
START-UP TIME
The start-up time and settling time to within 1% of the
final frequency is typically 100μs.
to 90% of the rise or fall transition). If the total output rise
time plus fall time is arbitrarily specified to be equal to
or less than 20% of the oscillator’s period (1/fOSC), then
the maximum output CLOAD in picofarads (pF) should be
equal to or less than [45454/(ROUT • fOSC)] (ROUT in ohms
and fOSC in MHz).
Example: An LTC6905 is operating with a 3V power supply
and is set for a fOSC = 50MHz.
ROUT with V+ = 3V is 27Ω (using the ROUT vs V+ graph in
the Typical Performance Characteristics).
The maximum output CLOAD should be equal to or less
than [45454/(27 • 50)] = 33.6pF.
The lowest resistive load Pin 5 can drive can be calculated
using the minimum high level output voltage in the Electrical
Characteristics. With a V+ equal to 5.5V and 4mA output
current, the minimum high level output voltage is 5V and
the lowest resistive load Pin 5 can drive is 1.25k (5V/4mA).
With a V+ equal to 2.7V and 4mA output current, the
minimum high level output voltage is 1.9V and the lowest
resistive load Pin 5 can drive is 475Ω (1.9V/4mA).
FREQUENCY ACCURACY AND POWER SUPPLY NOISE
The frequency accuracy of the LTC6905 may be affected
when its power supply generates noise with frequency
contents equal to fMO/64 or its multiples (fMO is the
internal LTC6905 master oscillator frequency before the
divider and fMO/64 is the master oscillator control loop
frequency). If for example, the master oscillator frequency
is set equal to 80MHz and the LTC6905 is powered by a
switching regulator, then the oscillator frequency may
show an additional error if the switching frequency is
1.4MHz (80MHz/64).
MAXIMUM OUTPUT LOAD
The LTC6905 output (Pin 5) can drive a capacitive load
(CLOAD) of 5pF or more. Driving a CLOAD greater than 5pF
depends on the oscillator’s frequency (fOSC) and output
resistance (ROUT). The output rise time or fall time due to
ROUT and CLOAD is equal to 2.2 • ROUT • CLOAD (from 10%
JITTER AND POWER SUPPLY NOISE
If the LTC6905 is powered by a supply that has frequency
contents equal to the output frequency then the oscillators
jitter may increase. In addition, power supply ripple in
excess of 20mV at any frequency may increase jitter.
6905fd
8
LTC6905
APPLICATIONS INFORMATION
JITTER AND DIVIDE RATIO
At a given output frequency, a higher master oscillator
frequency and a higher divide ratio will result in lower
jitter and higher power supply dissipation. Indeterminate
jitter percentage will decrease by a factor of slightly less
than the square root of the divider ratio, while determinate
jitter will not be similarly attenuated. Please consult the
specification tables and Jitter vs Frequency graph showing
jitter at various divider ratios.
JITTER AND STRAY CAPACITANCE ON THE SET PIN
(PIN 3)
The stray capacitance on the SET pin (Pin 3) should be
limited to 10pF or less to avoid increased jitter or unstable
oscillation.
LTC6905 SUGGESTED CRITICAL COMPONENT LAYOUT
In order to provide the specified performance, it is required that the frequency setting resistor RSET and the
supply bypass capacitor be placed as close as possible
to the LTC6905. The following additional rules should be
followed for best performance:
1) The bypass capacitor must be placed as close as possible
to the LTC6905, and no vias should be placed between
the capacitor and the LTC6905. The bypass capacitor
must be on the same side of the circuit board as the
LTC6905.
2) The resistor RSET should be placed as close as possible
to the LTC6905, and the connection of RSET to VCC
should be closely shared with the bypass capacitor.
The resistor RSET may be placed on the opposite side
of the board from the LTC6905, directly underneath the
bypass capacitor.
3) If a ground plane is used, the connection of the LTC6905
to the ground plane should be as close as possible
to the LTC6905 GND pin and should be composed of
multiple, high current capacity vias.
R
C
LTC6905
6905 F02
Figure 2. LTC6905 Suggested Critical Component Layout
6905fd
9
LTC6905
APPLICATIONS INFORMATION
ALTERNATIVE METHODS OF SETTING THE OUTPUT
FREQUENCY OF THE LTC6905
The LTC6905 may be programmed by any method that
sources a current into the SET pin (Pin 3). The accuracy
of the programming is best with a simple resistor because
the LTC6905 takes into account both the voltage at the SET
pin and the current into the SET pin when generating the
output frequency. Since the voltage at the SET pin can
vary by as much as 5%, setting the frequency using a
current rather than a resistor will result in as much as 5%
additional inaccuracy in the output frequency.
V+
1
0.1μF
RSET
10k
OUT
V+
LTC6905
2
5
fOSC
69.8MHz TO 170MHz
GND
3
SET
ICNTRL
0μA TO 60μA
DIV
V+
N=1
4
6905 F03
Figure 3. Current Controlled Oscillator
Figure 3 shows a method to control the frequency of the
LTC6905 using a current source. RSET , in this case, sets a
maximum frequency according to the regular expression
for fOSC. The current source will subtract current from the
SET pin to lower the frequency.
Figure 4 shows a method for controlling the frequency
of the LTC6905 using a voltage source. In this case, RSET
sets a constant current into the SET pin, and RCNTRL will
subtract from this current in order to change the frequency.
Increasing VCNTRL will increase the output frequency.
⎤
⎡
⎤
⎡ V + – VSET
– ICNTRL ⎥
⎥
⎢ 168.5MHz • 10kΩ • ⎢
⎥
1⎢
⎥⎦
⎢⎣ RSET
+ 1.5MHz ⎥
fOSC = ⎢
N⎢
V + – VSET
⎥
⎥
⎢
⎦
⎣
ICNTRL Frequency ≤ 100kHz
Example (Figure 3): VSET = (V+ – 1V), RSET = 10k, N = 1
fOSC = [168.5MHz • (1 – 10kΩ • ICNTRL) + 1.5MHz
V+ = 3V
0.1μF
RSET
10k
RCNTRL
33.2k
+
–
1
2
3
OUT
V+
LTC6905
5
fOSC
69.8MHz TO 170MHz
GND
SET
DIV
4
V+
N=1
6905 F04
VCNTRL
0V TO 2V
Figure 4. Voltage Controlled Oscillator
⎤
⎡
⎡ V + – VSET VSET – VCNTRL ⎤
–
⎥
⎢ 168.5MHz • 10kΩ • ⎢
⎥
RCNTRL
⎥
1⎢
⎢⎣ RSET
⎥⎦
fOSC = ⎢
+ 1.5MHz ⎥
+
N⎢
V – VSET
⎥
⎢
⎥
⎦
⎣
VCNTRL Frequency ≤ 100kHz
Example (Figure 4): VSET = (V+ – 1V), RSET = 10k, RCNTRL = 33.2k,
N = 1, V+ = 3V
⎡
⎤
⎡ 1
2V – VCNTRL ⎤
fOSC = ⎢168.5MHz • 10kΩ • ⎢
–
+ 1.5MHz⎥
⎥
33.2kΩ ⎦
⎣ 10kΩ
⎣
⎦
6905fd
10
LTC6905
PACKAGE DESCRIPTION
S5 Package
5-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1635)
0.62
MAX
0.95
REF
2.90 BSC
(NOTE 4)
1.22 REF
1.4 MIN
3.85 MAX 2.62 REF
2.80 BSC
1.50 – 1.75
(NOTE 4)
PIN ONE
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.30 – 0.45 TYP
5 PLCS (NOTE 3)
0.95 BSC
0.80 – 0.90
0.20 BSC
0.01 – 0.10
1.00 MAX
DATUM ‘A’
0.30 – 0.50 REF
0.09 – 0.20
(NOTE 3)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. JEDEC PACKAGE REFERENCE IS MO-193
1.90 BSC
S5 TSOT-23 0302
6905fd
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LTC6905
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1799
1kHz to 33MHz ThinSOT Oscillator
Single Output, High Frequency Operation
LTC6900
1kHz to 20MHz ThinSOT Oscillator
Single Output Lower Power
LTC6902
Multiphase Oscillator with Spread Spectrum Modulation
LTC6903/LTC6904
1kHz to 68MHz Serial Port Programmable Oscillator
2-, 3- or 4-Phase Outputs
3-Wire or I2C™ Programmable
LTC6905-XXX Series
Fixed Frequency LTC6905
High Accuracy, No External Resistor
LTC6906
Micropower, 10kHz to 1MHz Resistor Set ThinSOT Oscillator
Ultralow Power, Resistor Sets Frequency
6905fd
12 Linear Technology Corporation
LT 0808 REV D • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2005
工商网监
湘ICP备2023018690号
